Search Results

Search found 8018 results on 321 pages for 'active relation'.

Page 305/321 | < Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >

• fd partitions gone from 2 discs, md happy with it and resyncs. How to recover ?

  - by d0nd

  Hey gurus, need some help badly with this one. I run a server with a 6Tb md raid5 volume built over 7*1Tb disks. I've had to shut down the server lately and when it went back up, 2 out of the 7 disks used for the raid volume had lost its conf : dmesg : [ 10.184167] sda: sda1 sda2 sda3 // System disk [ 10.202072] sdb: sdb1 [ 10.210073] sdc: sdc1 [ 10.222073] sdd: sdd1 [ 10.229330] sde: sde1 [ 10.239449] sdf: sdf1 [ 11.099896] sdg: unknown partition table [ 11.255641] sdh: unknown partition table All 7 disks have same geometry and were configured alike : dmesg : Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect All 7 disks (sdb1, sdc1, sdd1, sde1, sdf1, sdg1, sdh1) were used in a md raid5 xfs volume. When booting, md, which was (obviously) out of sync kicked in and automatically started rebuilding over the 7 disks, including the two "faulty" ones; xfs tried to do some shenanigans as well: dmesg : [ 19.566941] md: md0 stopped. [ 19.817038] md: bind<sdc1> [ 19.817339] md: bind<sdd1> [ 19.817465] md: bind<sde1> [ 19.817739] md: bind<sdf1> [ 19.817917] md: bind<sdh> [ 19.818079] md: bind<sdg> [ 19.818198] md: bind<sdb1> [ 19.818248] md: md0: raid array is not clean -- starting background reconstruction [ 19.825259] raid5: device sdb1 operational as raid disk 0 [ 19.825261] raid5: device sdg operational as raid disk 6 [ 19.825262] raid5: device sdh operational as raid disk 5 [ 19.825264] raid5: device sdf1 operational as raid disk 4 [ 19.825265] raid5: device sde1 operational as raid disk 3 [ 19.825267] raid5: device sdd1 operational as raid disk 2 [ 19.825268] raid5: device sdc1 operational as raid disk 1 [ 19.825665] raid5: allocated 7334kB for md0 [ 19.825667] raid5: raid level 5 set md0 active with 7 out of 7 devices, algorithm 2 [ 19.825669] RAID5 conf printout: [ 19.825670] --- rd:7 wd:7 [ 19.825671] disk 0, o:1, dev:sdb1 [ 19.825672] disk 1, o:1, dev:sdc1 [ 19.825673] disk 2, o:1, dev:sdd1 [ 19.825675] disk 3, o:1, dev:sde1 [ 19.825676] disk 4, o:1, dev:sdf1 [ 19.825677] disk 5, o:1, dev:sdh [ 19.825679] disk 6, o:1, dev:sdg [ 19.899787] PM: Starting manual resume from disk [ 28.663228] Filesystem "md0": Disabling barriers, not supported by the underlying device [ 28.663228] XFS mounting filesystem md0 [ 28.884433] md: resync of RAID array md0 [ 28.884433] md: minimum _guaranteed_ speed: 1000 KB/sec/disk. [ 28.884433] md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for resync. [ 28.884433] md: using 128k window, over a total of 976759936 blocks. [ 29.025980] Starting XFS recovery on filesystem: md0 (logdev: internal) [ 32.680486] XFS: xlog_recover_process_data: bad clientid [ 32.680495] XFS: log mount/recovery failed: error 5 [ 32.682773] XFS: log mount failed I ran fdisk and flagged sdg1 and sdh1 as fd. I tried to reassemble the array but it didnt work: no matter what was in mdadm.conf, it still uses sdg and sdh instead of sdg1 and sdh1. I checked in /dev and I see no sdg1 and and sdh1, shich explains why it wont use it. I just don't know why those partitions are gone from /dev and how to readd those... blkid : /dev/sda1: LABEL="boot" UUID="519790ae-32fe-4c15-a7f6-f1bea8139409" TYPE="ext2" /dev/sda2: TYPE="swap" /dev/sda3: LABEL="root" UUID="91390d23-ed31-4af0-917e-e599457f6155" TYPE="ext3" /dev/sdb1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdc1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdd1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sde1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdf1: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdg: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" /dev/sdh: UUID="2802e68a-dd11-c519-e8af-0d8f4ed72889" TYPE="mdraid" fdisk -l : Disk /dev/sda: 40.0 GB, 40020664320 bytes 255 heads, 63 sectors/track, 4865 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8c878c87 Device Boot Start End Blocks Id System /dev/sda1 * 1 12 96358+ 83 Linux /dev/sda2 13 134 979965 82 Linux swap / Solaris /dev/sda3 135 4865 38001757+ 83 Linux Disk /dev/sdb: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x1e7481a5 Device Boot Start End Blocks Id System /dev/sdb1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdc: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xc9bdc1e9 Device Boot Start End Blocks Id System /dev/sdc1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdd: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xcc356c30 Device Boot Start End Blocks Id System /dev/sdd1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sde: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xe87f7a3d Device Boot Start End Blocks Id System /dev/sde1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdf: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xb17a2d22 Device Boot Start End Blocks Id System /dev/sdf1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdg: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0x8f3bce61 Device Boot Start End Blocks Id System /dev/sdg1 1 121601 976760001 fd Linux raid autodetect Disk /dev/sdh: 1000.2 GB, 1000204886016 bytes 255 heads, 63 sectors/track, 121601 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Disk identifier: 0xa98062ce Device Boot Start End Blocks Id System /dev/sdh1 1 121601 976760001 fd Linux raid autodetect I really dont know what happened nor how to recover from this mess. Needless to say the 5TB or so worth of data sitting on those disks are very valuable to me... Any idea any one? Did anybody ever experienced a similar situation or know how to recover from it ? Can someone help me? I'm really desperate... :x

  Read the article

• CISCO 2911 Router configuration

  - by bala

  Device cisco 2911 router configuration support is required please. I have exchange server 2010 configured and working without any errors the problem is in cisco router configuration when exchange server sends emails out the receives WAN IP not the public ip. I have configured RDNS lookups with our MX record IP addesses that match the FQDN but all our emails are rejected because it does not match with the public ip. Receiving mails problem is not an problem all mails are coming through. i am sure i am missing something on the router configuration that does not sends the public ip, can any one help me to solve this issue. Note; I've got 1 WAN IP & 8 Public IP from ISP . Find below the running configuration. Building configuration... Current configuration : 2734 bytes ! ! Last configuration change at 06:32:13 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 ! NVRAM config last updated at 06:32:14 UTC Tue Apr 3 2012 version 15.1 service timestamps debug datetime msec service timestamps log datetime msec service password-encryption ! hostname BSBG-LL ! boot-start-marker boot-end-marker ! ! enable secret 5 $x$xHrxxxxx5ox0 enable password 7 xx23xx5FxxE1xx044 ! no aaa new-model ! no ipv6 cef ip source-route ip cef ! ! ! ! ! ip flow-cache timeout active 1 ip domain name yourdomain.com ip name-server 213.42.20.20 ip name-server 195.229.241.222 multilink bundle-name authenticated ! ! crypto pki token default removal timeout 0 ! ! license udi pid CISCO2911/K9 ! ! username bsbg ! ! ! ! ! ! interface Embedded-Service-Engine0/0 no ip address shutdown ! interface GigabitEthernet0/0 ip address 192.168.0.9 255.255.255.0 ip flow ingress ip nat inside ip virtual-reassembly in duplex auto speed 100 no cdp enable ! interface GigabitEthernet0/1 ip address 213.42.xx.x2 255.255.255.252 ip nat outside ip virtual-reassembly in duplex auto speed auto no cdp enable ! interface GigabitEthernet0/2 no ip address shutdown duplex auto speed auto ! ip forward-protocol nd ! no ip http server no ip http secure-server ! ip nat inside source list 120 interface GigabitEthernet0/1 overload ip nat inside source static tcp 192.168.0.4 25 94.56.89.100 25 extendable ip nat inside source static tcp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static udp 192.168.0.4 53 94.56.89.100 53 extendable ip nat inside source static tcp 192.168.0.4 110 94.56.89.100 110 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.100 443 extendable ip nat inside source static tcp 192.168.0.4 587 94.56.89.100 587 extendable ip nat inside source static tcp 192.168.0.4 995 94.56.89.100 995 extendable ip nat inside source static tcp 192.168.0.4 3389 94.56.89.100 3389 extendable ip nat inside source static tcp 192.168.0.4 443 94.56.89.101 443 extendable ip nat inside source static tcp 192.168.0.12 80 94.56.89.102 80 extendable ip nat inside source static tcp 192.168.0.12 443 94.56.89.102 443 extendable ip nat inside source static tcp 192.168.0.12 3389 94.56.89.102 3389 extendable ip route 0.0.0.0 0.0.0.0 213.42.69.41 ! access-list 120 permit ip 192.168.0.0 0.0.0.255 any ! ! ! control-plane ! ! ! line con 0 exec-timeout 5 0 line aux 0 line 2 no activation-character no exec transport preferred none transport input all transport output pad telnet rlogin lapb-ta mop udptn v120 ssh stopbits 1 line vty 0 4 password 7 xx64xxD530D26086Dxx login transport input all ! scheduler allocate 20000 1000 end

  Read the article

• Passing a variable from Excel 2007 Custom Task Pane to Hosted PowerShell

  - by Uros Calakovic

  I am testing PowerShell hosting using C#. Here is a console application that works: using System; using System.Collections; using System.Collections.Generic; using System.Collections.ObjectModel; using System.Management.Automation; using System.Management.Automation.Runspaces; using Microsoft.Office.Interop.Excel; namespace ConsoleApplication3 { class Program { static void Main() { Application app = new Application(); app.Visible = true; app.Workbooks.Add(XlWBATemplate.xlWBATWorksheet); Runspace runspace = RunspaceFactory.CreateRunspace(); runspace.Open(); runspace.SessionStateProxy.SetVariable("Application", app); Pipeline pipeline = runspace.CreatePipeline("$Application"); Collection<PSObject> results = null; try { results = pipeline.Invoke(); foreach (PSObject pob in results) { Console.WriteLine(pob); } } catch (RuntimeException re) { Console.WriteLine(re.GetType().Name); Console.WriteLine(re.Message); } } } } I first create an Excel.Application instance and pass it to the hosted PowerShell instance as a varible named $Application. This works and I can use this variable as if Excel.Application was created from within PowerShell. I next created an Excel addin using VS 2008 and added a user control with two text boxes and a button to the addin (the user control appears as a custom task pane when Excel starts). The idea was this: when I click the button a hosted PowerShell instance is created and I can pass to it the current Excel.Application instance as a variable, just like in the first sample, so I can use this variable to automate Excel from PowerShell (one text box would be used for input and the other one for output. Here is the code: using System; using System.Windows.Forms; using System.Management.Automation; using System.Management.Automation.Runspaces; using System.Collections.ObjectModel; using Microsoft.Office.Interop.Excel; namespace POSHAddin { public partial class POSHControl : UserControl { public POSHControl() { InitializeComponent(); } private void btnRun_Click(object sender, EventArgs e) { txtOutput.Clear(); Microsoft.Office.Interop.Excel.Application app = Globals.ThisAddIn.Application; Runspace runspace = RunspaceFactory.CreateRunspace(); runspace.Open(); runspace.SessionStateProxy.SetVariable("Application", app); Pipeline pipeline = runspace.CreatePipeline( "$Application | Get-Member | Out-String"); app.ActiveCell.Value2 = "Test"; Collection<PSObject> results = null; try { results = pipeline.Invoke(); foreach (PSObject pob in results) { txtOutput.Text += pob.ToString() + "-"; } } catch (RuntimeException re) { txtOutput.Text += re.GetType().Name; txtOutput.Text += re.Message; } } } } The code is similar to the first sample, except that the current Excel.Application instance is available to the addin via Globals.ThisAddIn.Application (VSTO generated) and I can see that it is really a Microsoft.Office.Interop.Excel.Application instance because I can use things like app.ActiveCell.Value2 = "Test" (this actually puts the text into the active cell). But when I pass the Excel.Application instance to the PowerShell instance what gets there is an instance of System.__ComObject and I can't figure out how to cast it to Excel.Application. When I examine the variable from PowerShell using $Application | Get-Member this is the output I get in the second text box: TypeName: System.__ComObject Name MemberType Definition ---- ---------- ---------- CreateObjRef Method System.Runtime.Remoting.ObjRef CreateObj... Equals Method System.Boolean Equals(Object obj) GetHashCode Method System.Int32 GetHashCode() GetLifetimeService Method System.Object GetLifetimeService() GetType Method System.Type GetType() InitializeLifetimeService Method System.Object InitializeLifetimeService() ToString Method System.String ToString() My question is how can I pass an instance of Microsoft.Office.Interop.Excel.Application from a VSTO generated Excel 2007 addin to a hosted PowerShell instance, so I can manipulate it from PowerShell? (I have previously posted the question in the Microsoft C# forum without an answer)

  Read the article

• Rails routing to XML/JSON without views gone mad

  - by John Schulze

  I have a mystifying problem. In a very simple Ruby app i have three classes: Drivers, Jobs and Vehicles. All three classes only consist of Id and Name. All three classes have the same #index and #show methods and only render in JSON or XML (this is in fact true for all their CRUD methods, they are identical in everything but name). There are no views. For example: def index @drivers= Driver.all respond_to do |format| format.js { render :json => @drivers} format.xml { render :xml => @drivers} end end def show @driver = Driver.find(params[:id]) respond_to do |format| format.js { render :json => @driver} format.xml { render :xml => @driver} end end The models are similarly minimalistic and only contain: class Driver< ActiveRecord::Base validates_presence_of :name end In routes.rb I have: map.resources :drivers map.resources :jobs map.resources :vehicles map.connect ':controller/:action/:id' map.connect ':controller/:action/:id.:format' I can perform POST/create, GET/index and PUT/update on all three classes and GET/read used to work as well until I installed the "has many polymorphs" ActiveRecord plugin and added to environment.rb: require File.join(File.dirname(__FILE__), 'boot') require 'has_many_polymorphs' require 'active_support' Now for two of the three classes I cannot do a read any more. If i go to localhost:3000/drivers they all list nicely in XML but if i go to localhost:3000/drivers/3 I get an error: Processing DriversController#show (for 127.0.0.1 at 2009-06-11 20:34:03) [GET] Parameters: {"id"=>"3"} [4;36;1mDriver Load (0.0ms)[0m [0;1mSELECT * FROM "drivers" WHERE ("drivers"."id" = 3) [0m ActionView::MissingTemplate (Missing template drivers/show.erb in view path app/views): app/controllers/drivers_controller.rb:14:in `show' ...etc This is followed a by another unexpected error: Processing ApplicationController#show (for 127.0.0.1 at 2009-06-11 21:35:52)[GET] Parameters: {"id"=>"3"} NameError (uninitialized constant ApplicationController::AreaAccessDenied): ...etc What is going on here? Why does the same code work for one class but not the other two? Why is it trying to do a #view on the ApplicationController? I found that if I create a simple HTML view for each of the three classes these work fine. To each class I add: format.html # show.html.erb With this in place, going to localhost:3000/drivers/3 renders out the item in HTML and I get no errors in the log. But if attach .xml to the URL it again fails for two of the classes (with the same error message as before) while one will output XML as expected. Even stranger, on the two failing classes, when adding .js to the URL (to trigger JSON rendering) I get the HTML output instead! Is it possible this has something to do with the "has many polymorphs" plugin? I have heard of people having routing issues after installing it. Removing "has many polymorphs" and "active support" from environment.rb (and rebooting the sever) seems to make no difference whatsoever. Yet my problems started after it was installed. I've spent a number of hours on this problem now and am starting to get a little desperate, Google turns up virtually no information which makes me suspect I must have missed something elementary. Any enlightenment or hint gratefully received! JS

  Read the article

• Tomcat 7 on Ubuntu 12.04 with JRE 7 not starting

  - by Andreas Krueger

  I am running a virtual server in the web on Ubuntu 12.04 LTS / 32 Bit. After a clean install of JRE 7 and Tomcat 7, following the instructions on http://www.sysadminslife.com, I don't get Tomcat 7 up and running. > java -version java version "1.7.0_09" Java(TM) SE Runtime Environment (build 1.7.0_09-b05) Java HotSpot(TM) Client VM (build 23.5-b02, mixed mode) > /etc/init.d/tomcat start Starting Tomcat Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr/lib/jvm/java-7-oracle Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar:/usr/local/tomcat/bin/tomcat-juli.jar > telnet localhost 8080 Trying ::1... Trying 127.0.0.1... telnet: Unable to connect to remote host: Connection refused netstat sometimes shows a Java process, most of the times not. If it does, nothing works either. Does anyone have a solution or encountered similar situations? Here are the contents of catalina.out: 16.11.2012 18:36:39 org.apache.catalina.core.AprLifecycleListener init INFO: The APR based Apache Tomcat Native library which allows optimal performance in production environments was not found on the java.library.path: /usr/lib/jvm/java-6-oracle/lib/i386/client:/usr/lib/jvm/java-6-oracle/lib/i386:/usr/lib/jvm/java-6-oracle/../lib/i386:/usr/java/packages/lib/i386:/lib:/usr/lib 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["http-bio-8080"] 16.11.2012 18:36:40 org.apache.coyote.AbstractProtocol init INFO: Initializing ProtocolHandler ["ajp-bio-8009"] 16.11.2012 18:36:40 org.apache.catalina.startup.Catalina load INFO: Initialization processed in 1509 ms 16.11.2012 18:36:40 org.apache.catalina.core.StandardService startInternal INFO: Starting service Catalina 16.11.2012 18:36:40 org.apache.catalina.core.StandardEngine startInternal INFO: Starting Servlet Engine: Apache Tomcat/7.0.29 16.11.2012 18:36:40 org.apache.catalina.startup.HostConfig deployDirectory INFO: Deploying web application directory /usr/local/tomcat/webapps/manager Here come the results of ps -ef, iptables --list and netstat -plut: > ps -ef UID PID PPID C STIME TTY TIME CMD root 1 0 0 Nov16 ? 00:00:00 init root 2 1 0 Nov16 ? 00:00:00 [kthreadd/206616] root 3 2 0 Nov16 ? 00:00:00 [khelper/2066167] root 4 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 5 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 6 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 7 2 0 Nov16 ? 00:00:00 [rpciod/2066167/] root 8 2 0 Nov16 ? 00:00:00 [nfsiod/2066167] root 119 1 0 Nov16 ? 00:00:00 upstart-udev-bridge --daemon root 125 1 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 157 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 158 125 0 Nov16 ? 00:00:00 /sbin/udevd --daemon root 205 1 0 Nov16 ? 00:00:00 upstart-socket-bridge --daemon root 276 1 0 Nov16 ? 00:00:00 /usr/sbin/sshd -D root 335 1 0 Nov16 ? 00:00:00 /usr/sbin/xinetd -dontfork -pidfile /var/run/xinetd.pid -stayalive -inetd root 348 1 0 Nov16 ? 00:00:00 cron syslog 368 1 0 Nov16 ? 00:00:00 /sbin/syslogd -u syslog root 472 1 0 Nov16 ? 00:00:00 /usr/lib/postfix/master postfix 482 472 0 Nov16 ? 00:00:00 qmgr -l -t fifo -u root 520 1 0 Nov16 ? 00:00:04 /usr/sbin/apache2 -k start www-data 523 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 525 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start www-data 526 520 0 Nov16 ? 00:00:00 /usr/sbin/apache2 -k start tomcat 1074 1 0 Nov16 ? 00:01:08 /usr/lib/jvm/java-6-oracle/bin/java -Djava.util.logging.config.file=/usr/ postfix 1351 472 0 Nov16 ? 00:00:00 tlsmgr -l -t unix -u -c postfix 3413 472 0 17:00 ? 00:00:00 pickup -l -t fifo -u -c root 3457 276 0 17:31 ? 00:00:00 sshd: root@pts/0 root 3459 3457 0 17:31 pts/0 00:00:00 -bash root 3470 3459 0 17:31 pts/0 00:00:00 ps -ef > iptables --list Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt ACCEPT tcp -- anywhere anywhere tcp dpt:8005 ACCEPT tcp -- anywhere anywhere tcp dpt:http-alt Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination > netstat -plut Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 *:smtp *:* LISTEN 472/master tcp 0 0 *:3213 *:* LISTEN 276/sshd tcp6 0 0 [::]:smtp [::]:* LISTEN 472/master tcp6 0 0 [::]:8009 [::]:* LISTEN 1074/java tcp6 0 0 [::]:3213 [::]:* LISTEN 276/sshd tcp6 0 0 [::]:http-alt [::]:* LISTEN 1074/java tcp6 0 0 [::]:http [::]:* LISTEN 520/apache2

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• Forms bound to updateable ADO recordsets are not updateable when the source includes a JOIN

  - by Art

  I'm developing an application in Access 2007. It uses an .accdb front end connecting to an SQL Server 2005 backend. I use forms that are bound to ADO recordsets at runtime. For the sake of efficiency, the recordsets usually contain only one record, and are queried out on the server: Public Sub SetUpFormRecordset(cn As ADODB.Connection, rstIn As ADODB.Recordset, rstSource As String) Dim cmd As ADODB.Command Dim I As Long Set cmd = New ADODB.Command cn.Errors.Clear ' Recordsets based on command object Execute method are Read Only! With cmd Set .ActiveConnection = cn .CommandType = adCmdText .CommandText = rstSource End With With rstIn .CursorType = adOpenKeyset .LockType = adLockPessimistic 'Check the locktype after opening; optimistic locking is worthless on a bound End With ' form, and ADO might open optimistically without firing an error! rstIn.Open cmd, , adOpenKeyset, adLockPessimistic 'This should run the query on the server and return an updatable recordset With cn If .Errors.Count <> 0 Then For Each errADO In .Errors Call HandleADOErrors(.Errors(I)) I = I + 1 Next errADO End If End With End Sub rstSource (the string containg the TSQL on which the recordset is based) is assembled by the calling routine, in this case from the Open event of the form being bound: Private Sub Form_Open(Cancel As Integer) Dim rst As ADODB.Recordset Dim strSource As String, DefaultSource as String Dim lngID As Long lngID = Forms!MyParent.CurrentID strSource = "SELECT TOP (100) PERCENT dbo.Customers.CustomerID, dbo.Customers.LegacyID, dbo.Customers.Active, dbo.Customers.TypeID, dbo.Customers.Category, " & _ "dbo.Customers.Source, dbo.Customers.CustomerName, dbo.Customers.CustAddrID, dbo.Customers.Email, dbo.Customers.TaxExempt, dbo.Customers.SalesTaxCode, " & _ "dbo.Customers.SalesTax2Code, dbo.Customers.CreditLimit, dbo.Customers.CreationDate, dbo.Customers.FirstOrder, dbo.Customers.LastOrder, " & _ "dbo.Customers.nOrders, dbo.Customers.Concurrency, dbo.Customers.LegacyLN, dbo.Addresses.AddrType, dbo.Addresses.AddrLine1, dbo.Addresses.AddrLine2, " & _ "dbo.Addresses.City, dbo.Addresses.State, dbo.Addresses.Country, dbo.Addresses.PostalCode, dbo.Addresses.PhoneLandline, dbo.Addresses.Concurrency " & _ "FROM dbo.Customers INNER JOIN " & _ "dbo.Addresses ON dbo.Customers.CustAddrID = dbo.Addresses.AddrID " strSource = strSource & "WHERE dbo.Customers.CustomerID= " & lngID With Me 'Default is Set up for editing one record If Not Nz(.RecordSource, vbNullString) = vbNullString Then If .Dirty Then .Dirty = False 'Save any changes on the form .RecordSource = vbNullString End If If rst Is Nothing Then 'Might not be first time through DefaultSource = .RecordSource Else rst.Close Set rst = Nothing End If End With Set rst = New ADODB.Recordset Call setupformrecordset(dbconn, rst, strSource) 'dbconn is a global variable With Me Set .Recordset = rst End With End Sub The recordset that is returned from setupformrecordset is fully updateable, and its .Supports property shows this. It can be edited and updated in code. The entire form, however, is read only, even though it's .AllowEdits and .AllowAdditions properties are both true. Even the fields from the right hand side (the 'many' side) cannot be edited. Removing the INNER JOIN clause from the TSQL (restricting strSource to one table) makes the form fully editable. I've verified that the TSQL includes priimary key fields from both tables, and each table includes a timestamp field for concurrency. I tried changing the .CursorType and .CursorLocation properties of the recordset to no avail. What am I doing wrong?

  Read the article

• C++ MySQL++ Delete query statement brain killer question

  - by shauny

  Hello all, I'm relatively new to the MySQL++ connector in C++, and have an really annoying issue with it already! I've managed to get stored procedures working, however i'm having issues with the delete statements. I've looked high and low and have found no documentation with examples. First I thought maybe the code needs to free the query/connection results after calling the stored procedure, but of course MySQL++ doesn't have a free_result method... or does it? Anyways, here's what I've got: #include <iostream> #include <stdio.h> #include <queue> #include <deque> #include <sys/stat.h> #include <mysql++/mysql++.h> #include <boost/thread/thread.hpp> #include "RepositoryQueue.h" using namespace boost; using namespace mysqlpp; class RepositoryChecker { private: bool _isRunning; Connection _con; public: RepositoryChecker() { try { this->_con = Connection(false); this->_con.set_option(new MultiStatementsOption(true)); this->_con.set_option(new ReconnectOption(true)); this->_con.connect("**", "***", "***", "***"); this->ChangeRunningState(true); } catch(const Exception& e) { this->ChangeRunningState(false); } } /** * Thread method which runs and creates the repositories */ void CheckRepositoryQueues() { //while(this->IsRunning()) //{ std::queue<RepositoryQueue> queues = this->GetQueue(); if(queues.size() > 0) { while(!queues.empty()) { RepositoryQueue &q = queues.front(); char cmd[256]; sprintf(cmd, "svnadmin create /home/svn/%s/%s/%s", q.GetPublicStatus().c_str(), q.GetUsername().c_str(), q.GetRepositoryName().c_str()); if(this->DeleteQueuedRepository(q.GetQueueId())) { printf("query deleted?\n"); } printf("Repository created!\n"); queues.pop(); } } boost::this_thread::sleep(boost::posix_time::milliseconds(500)); //} } protected: /** * Gets the latest queue of repositories from the database * and returns them inside a cool queue defined with the * RepositoryQueue class. */ std::queue<RepositoryQueue> GetQueue() { std::queue<RepositoryQueue> queues; Query query = this->_con.query("CALL sp_GetRepositoryQueue();"); StoreQueryResult result = query.store(); RepositoryQueue rQ; if(result.num_rows() > 0) { for(unsigned int i = 0;i < result.num_rows(); ++i) { rQ = RepositoryQueue((unsigned int)result[i][0], (unsigned int)result[i][1], (String)result[i][2], (String)result[i][3], (String)result[i][4], (bool)result[i][5]); queues.push(rQ); } } return queues; } /** * Allows the thread to be shut off. */ void ChangeRunningState(bool isRunning) { this->_isRunning = isRunning; } /** * Returns the running value of the active thread. */ bool IsRunning() { return this->_isRunning; } /** * Deletes the repository from the mysql queue table. This is * only called once it has been created. */ bool DeleteQueuedRepository(unsigned int id) { char cmd[256]; sprintf(cmd, "DELETE FROM RepositoryQueue WHERE Id = %d LIMIT 1;", id); Query query = this->_con.query(cmd); return (query.exec()); } }; I've removed all the other methods as they're not needed... Basically it's the DeleteQueuedRepository method which isn't working, the GetQueue works fine. PS: This is on a Linux OS (Ubuntu server) Many thanks, Shaun

  Read the article

• Software: Launching League of Legends spectator mode from Command Line (Mac)

  - by Alex Popov

  Background: tl;dr at the end League of Legends has a spectator mode, in which you can watch someone else's game (essentially a replay) with a 3 minute delay. Popular LoL website OP.GG has figured out a clever way of hosting these spectator games on their own servers, thereby making them replayable, as opposed to only being available while the game is on (as Riot does it). If you request a replay from OP.GG, it sends a batch file which looks for where the League is situated and then the magic happens: @start "" "League of Legends.exe" "8394" "LoLLauncher.exe" "" "spectator fspectate.op.gg:4081 tjJbtRLQ/HMV7HuAxWV0XsXoRB4OmFBr 1391881421 NA1" This works fine on Windows. I'm trying to get it to work on Mac (which has an official client). First I tried running the same command by hand, (split for convenience) /Applications/ ... /LeagueOfLegends.app/ ... /LeagueofLegends 8393 LoLLauncher \ /Applications/ ... /LolClient spectator fspectate.op.gg:4081 tjJbtRLQ/HMV7HuAxWV0XsXoRB4OmFBr 1391881421 NA1 Running this, however, just starts the LoLLauncher, which closes all the active League processes. The exactly same thing happens if I just call /Applications/ ... /LeagueOfLegends.app/ ... /LeagueofLegends Next I tried seeing what actually happens when Spectator mode is initiated so I ran $ ps -axf | grep -i lol which showed UID PID PPID C STIME TTY TIME CMD 503 3085 1 0 Wed02pm ?? 0:00.00 (LolClient) 503 24607 1 0 9:19am ?? 0:00.98 /Applications/League of Legends.app/Contents/LOL/RADS/system/UserKernel.app/Contents/MacOS/UserKernel updateandrun lol_launcher LoLLauncher.app 503 24610 24607 0 9:19am ?? 1:08.76 /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_launcher/releases/0.0.0.122/deploy/LoLLauncher.app/Contents/MacOS/LoLLauncher 503 24611 24610 0 9:19am ?? 1:23.02 /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_air_client/releases/0.0.0.127/deploy/bin/LolClient -runtime .\ -nodebug META-INF\AIR\application.xml .\ -- 8393 503 24927 24610 0 9:44am ?? 0:03.37 /Applications/League of Legends.app/Contents/LoL/RADS/solutions/lol_game_client_sln/releases/0.0.0.117/deploy/LeagueOfLegends.app/Contents/MacOS/LeagueofLegends 8394 LoLLauncher /Applications/League of Legends.app/Contents/LoL/RADS/projects/lol_air_client/releases/0.0.0.127/deploy/bin/LolClient spectator 216.133.234.17:8088 Yn1oMX/n3LpXNebibzUa1i3Z+s2HV0ul 1400781241 NA1 Of Interest: there is (LolClient) which I cannot kill by it's PID. UserKernel updateandrun lol_launcher LoLLauncher.app is launched first. LoLLauncher is launched by the UserKernel (as we can see from the PPID) The very long command (PID: 24927) is how Spectator mode is launched, and is also launched by UserKernel. Spectator mode is launched in exactly the same way that the OP.GG .bat wanted to, with the only difference that Spectator mode connects to Riot instead of OP.GG's spectate server. I tried attaching GDB to the LolClient, but I couldn't get anything meaningful from it since it's an Adobe AIR application (and I've never used GDB with code other than mine own). Next I ran dtruss -a -b 100m -f -p $PID on everything I could think of: the LolClient, the LolLauncher and the UserKernel and skimmed the half a million lines produced. I found stuff like the GET request used to get the information of the game to spectate, but I could not see any launch of the equivalent of League of Legends.exe with spectator options. Finally, I ran lsof | grep -i lol to see if anything else was opened in the process, but didn't find anything that seemed appropriate. Open were UserKernel, LolLauncher, LolClient, Adobe AIR, LeagueofLegends and then Bugsplat, all of which are expected. None of this seemed especially relevant to figuring out how LeagueofLegends was opened into spectator mode. It obviously can be done, since Spectator mode is accessible from within the client. It seems likely that it can be done from the CLI, since Windows can do it and the clients are supposed to equals. Unless I'm missing something in the difference between how UNIX and Windows handle CLI application launches. My question is if there are any other things I can try to figure out how to launch Spectator mode myself. tl;dr: Trying to get into spectator mode from the CLI. It's possible on Windows (see first code block) but it just restarts League on Mac. What else can I try to find what call is made, and how to reproduce it? PS: Please let me know how I can improve this question or its formatting, I'd love to use StackOverflow/SuperUser, but as the guys said on the podcast this week (Ep. 59) it's very intimidating. Sorry for posting this on StackOverflow the first time :(

  Read the article

• UIView, UIScrollView and UITextFields problem calling Method

  - by Jeff Groby

  I have a view with several embedded UITextFields, this UIView is subordinated to a UIScrollView in IB. Each text field is supposed to invoke a method called updateText defined in the viewcontroller implementation file when the user is done editing the field. For some reason, the method updateText never gets invoked. Anyone have any ideas how to go about fixing this? The method fired off just fine when the UIScrollView was not present in the project but the keyboard would cover the text fields during input, which was annoying. Now my textfields move up above the keyboard when it appears, but won't fire off the method when done editing. Here is my implementation file: #import "MileMarkerViewController.h" @implementation MileMarkerViewController @synthesize scrollView,milemarkerLogDate,milemarkerDesc,milemarkerOdobeg,milemarkerOdoend,milemarkerBusiness,milemarkerPersonal,milemarker; - (id)initWithNibName:(NSString *)nibNameOrNil bundle:(NSBundle *)nibBundleOrNil { if (self = [super initWithNibName:nibNameOrNil bundle:nibBundleOrNil]) { // Initialization code } return self; } - (BOOL) textFieldShouldReturn: (UITextField*) theTextField { return [theTextField resignFirstResponder]; } - (void)viewDidLoad { [super viewDidLoad]; [[NSNotificationCenter defaultCenter] addObserver: self selector: @selector(keyboardWasShown:) name: UIKeyboardDidShowNotification object: nil]; [[NSNotificationCenter defaultCenter] addObserver: self selector: @selector(keyboardWasHidden:) name: UIKeyboardDidHideNotification object: nil]; keyboardShown = NO; // 1 [scrollView setContentSize: CGSizeMake( 320, 480)]; // 2 } - (void)keyboardWasShown:(NSNotification*)aNotification { if (keyboardShown) return; NSDictionary* info = [aNotification userInfo]; // Get the size of the keyboard. NSValue* aValue = [info objectForKey:UIKeyboardBoundsUserInfoKey]; CGSize keyboardSize = [aValue CGRectValue].size; // Resize the scroll view (which is the root view of the window) CGRect viewFrame = [scrollView frame]; viewFrame.size.height -= keyboardSize.height; scrollView.frame = viewFrame; // Scroll the active text field into view. CGRect textFieldRect = [activeField frame]; [scrollView scrollRectToVisible:textFieldRect animated:YES]; keyboardShown = YES; } - (void)keyboardWasHidden:(NSNotification*)aNotification { NSDictionary* info = [aNotification userInfo]; // Get the size of the keyboard. NSValue* aValue = [info objectForKey:UIKeyboardBoundsUserInfoKey]; CGSize keyboardSize = [aValue CGRectValue].size; // Reset the height of the scroll view to its original value CGRect viewFrame = [scrollView frame]; viewFrame.size.height += keyboardSize.height; [scrollView scrollRectToVisible:CGRectMake(0, 0, 1, 1) animated:YES]; scrollView.frame = viewFrame; keyboardShown = NO; } - (void)textFieldDidBeginEditing:(UITextField *)textField { activeField = textField; } - (void)textFieldDidEndEditing:(UITextField *)textField { activeField = nil; } - (IBAction)updateText:(id) sender { NSLog(@"You just entered: %@",self.milemarkerLogDate.text); self.milemarker.logdate = self.milemarkerLogDate.text; self.milemarker.desc = self.milemarkerDesc.text; self.milemarker.odobeg = self.milemarkerOdobeg.text; self.milemarker.odoend = self.milemarkerOdoend.text; self.milemarker.business = self.milemarkerBusiness.text; self.milemarker.personal = self.milemarkerPersonal.text; NSLog(@"Original textfield is set to: %@",self.milemarker.logdate); [self.milemarker updateText]; } - (void)didReceiveMemoryWarning { // Releases the view if it doesn't have a superview. [super didReceiveMemoryWarning]; // Release any cached data, images, etc that aren't in use. } - (void)dealloc { [super dealloc]; } @end

  Read the article

• JPA : Add and remove operations on lazily initialized collection behaviour ?

  - by Albert Kam

  Hello, im currently trying out JPA 2 and using Hibernate 3.6.x as the engine. I have an entity of ReceivingGood that contains a List of ReceivingGoodDetail, and has a bidirectional relation. Some related codes for each entity follows : ReceivingGood.java @OneToMany(mappedBy="receivingGood", targetEntity=ReceivingGoodDetail.class, fetch=FetchType.LAZY, cascade = CascadeType.ALL) private List<ReceivingGoodDetail> details = new ArrayList<ReceivingGoodDetail>(); public void addReceivingGoodDetail(ReceivingGoodDetail receivingGoodDetail) { receivingGoodDetail.setReceivingGood(this); } void internalAddReceivingGoodDetail(ReceivingGoodDetail receivingGoodDetail) { this.details.add(receivingGoodDetail); } public void removeReceivingGoodDetail(ReceivingGoodDetail receivingGoodDetail) { receivingGoodDetail.setReceivingGood(null); } void internalRemoveReceivingGoodDetail(ReceivingGoodDetail receivingGoodDetail) { this.details.remove(receivingGoodDetail); } @ManyToOne @JoinColumn(name = "receivinggood_id") private ReceivingGood receivingGood; ReceivingGoodDetail.java : public void setReceivingGood(ReceivingGood receivingGood) { if (this.receivingGood != null) { this.receivingGood.internalRemoveReceivingGoodDetail(this); } this.receivingGood = receivingGood; if (receivingGood != null) { receivingGood.internalAddReceivingGoodDetail(this); } } In my experiements with both of these entities, both adding the detail to the receivingGood's collection, and even removing the detail from the receivingGood's collection, will trigger a query to fill the collection before doing the add or remove. This assumption is based on my experiments that i will paste below. My concern is that : is it ok to do changes on only a little bit of records on the collection, and the engine has to query all of the details belonging to the collection ? What if the collection would have to be filled with 1000 records when i just want to edit a single record ? Here are my experiments with the output as the comment above each method : /* Hibernate: select receivingg0_.id as id9_14_, receivingg0_.creationDate as creation2_9_14_, ... too long Hibernate: select receivingg0_.id as id10_20_, receivingg0_.creationDate as creation2_10_20_, ... too long removing existing detail from lazy collection Hibernate: select details0_.receivinggood_id as receivi13_9_8_, details0_.id as id8_, details0_.id as id10_7_, details0_.creationDate as creation2_10_7_, details0_.modificationDate as modifica3_10_7_, details0_.usercreate_id as usercreate10_10_7_, details0_.usermodify_id as usermodify11_10_7_, details0_.version as version10_7_, details0_.buyQuantity as buyQuant5_10_7_, details0_.buyUnit as buyUnit10_7_, details0_.internalQuantity as internal7_10_7_, details0_.internalUnit as internal8_10_7_, details0_.product_id as product12_10_7_, details0_.receivinggood_id as receivi13_10_7_, details0_.supplierLotNumber as supplier9_10_7_, user1_.id as id2_0_, user1_.creationDate as creation2_2_0_, user1_.modificationDate as modifica3_2_0_, user1_.usercreate_id as usercreate6_2_0_, user1_.usermodify_id as usermodify7_2_0_, user1_.version as version2_0_, user1_.name as name2_0_, user2_.id as id2_1_, user2_.creationDate as creation2_2_1_, user2_.modificationDate as modifica3_2_1_, user2_.usercreate_id as usercreate6_2_1_, user2_.usermodify_id as usermodify7_2_1_, user2_.version as version2_1_, user2_.name as name2_1_, user3_.id as id2_2_, user3_.creationDate as creation2_2_2_, user3_.modificationDate as modifica3_2_2_, user3_.usercreate_id as usercreate6_2_2_, user3_.usermodify_id as usermodify7_2_2_, user3_.version as version2_2_, user3_.name as name2_2_, user4_.id as id2_3_, user4_.creationDate as creation2_2_3_, user4_.modificationDate as modifica3_2_3_, user4_.usercreate_id as usercreate6_2_3_, user4_.usermodify_id as usermodify7_2_3_, user4_.version as version2_3_, user4_.name as name2_3_, product5_.id as id0_4_, product5_.creationDate as creation2_0_4_, product5_.modificationDate as modifica3_0_4_, product5_.usercreate_id as usercreate7_0_4_, product5_.usermodify_id as usermodify8_0_4_, product5_.version as version0_4_, product5_.code as code0_4_, product5_.name as name0_4_, user6_.id as id2_5_, user6_.creationDate as creation2_2_5_, user6_.modificationDate as modifica3_2_5_, user6_.usercreate_id as usercreate6_2_5_, user6_.usermodify_id as usermodify7_2_5_, user6_.version as version2_5_, user6_.name as name2_5_, user7_.id as id2_6_, user7_.creationDate as creation2_2_6_, user7_.modificationDate as modifica3_2_6_, user7_.usercreate_id as usercreate6_2_6_, user7_.usermodify_id as usermodify7_2_6_, user7_.version as version2_6_, user7_.name as name2_6_ from ReceivingGoodDetail details0_ left outer join COMMON_USER user1_ on details0_.usercreate_id=user1_.id left outer join COMMON_USER user2_ on user1_.usercreate_id=user2_.id left outer join COMMON_USER user3_ on user2_.usermodify_id=user3_.id left outer join COMMON_USER user4_ on details0_.usermodify_id=user4_.id left outer join Product product5_ on details0_.product_id=product5_.id left outer join COMMON_USER user6_ on product5_.usercreate_id=user6_.id left outer join COMMON_USER user7_ on product5_.usermodify_id=user7_.id where details0_.receivinggood_id=? after removing try selecting the size : 4 after removing, now flushing Hibernate: update ReceivingGood set creationDate=?, modificationDate=?, usercreate_id=?, usermodify_id=?, version=?, purchaseorder_id=?, supplier_id=?, transactionDate=?, transactionNumber=?, transactionType=?, transactionYearMonth=?, warehouse_id=? where id=? and version=? Hibernate: update ReceivingGoodDetail set creationDate=?, modificationDate=?, usercreate_id=?, usermodify_id=?, version=?, buyQuantity=?, buyUnit=?, internalQuantity=?, internalUnit=?, product_id=?, receivinggood_id=?, supplierLotNumber=? where id=? and version=? detail size : 4 */ public void removeFromLazyCollection() { String headerId = "3b373f6a-9cd1-4c9c-9d46-240de37f6b0f"; ReceivingGood receivingGood = em.find(ReceivingGood.class, headerId); // get existing detail ReceivingGoodDetail detail = em.find(ReceivingGoodDetail.class, "323fb0e7-9bb2-48dc-bc07-5ff32f30e131"); detail.setInternalUnit("MCB"); System.out.println("removing existing detail from lazy collection"); receivingGood.removeReceivingGoodDetail(detail); System.out.println("after removing try selecting the size : " + receivingGood.getDetails().size()); System.out.println("after removing, now flushing"); em.flush(); System.out.println("detail size : " + receivingGood.getDetails().size()); } /* Hibernate: select receivingg0_.id as id9_14_, receivingg0_.creationDate as creation2_9_14_, ... too long Hibernate: select receivingg0_.id as id10_20_, receivingg0_.creationDate as creation2_10_20_, ... too long adding existing detail into lazy collection Hibernate: select details0_.receivinggood_id as receivi13_9_8_, details0_.id as id8_, details0_.id as id10_7_, details0_.creationDate as creation2_10_7_, details0_.modificationDate as modifica3_10_7_, details0_.usercreate_id as usercreate10_10_7_, details0_.usermodify_id as usermodify11_10_7_, details0_.version as version10_7_, details0_.buyQuantity as buyQuant5_10_7_, details0_.buyUnit as buyUnit10_7_, details0_.internalQuantity as internal7_10_7_, details0_.internalUnit as internal8_10_7_, details0_.product_id as product12_10_7_, details0_.receivinggood_id as receivi13_10_7_, details0_.supplierLotNumber as supplier9_10_7_, user1_.id as id2_0_, user1_.creationDate as creation2_2_0_, user1_.modificationDate as modifica3_2_0_, user1_.usercreate_id as usercreate6_2_0_, user1_.usermodify_id as usermodify7_2_0_, user1_.version as version2_0_, user1_.name as name2_0_, user2_.id as id2_1_, user2_.creationDate as creation2_2_1_, user2_.modificationDate as modifica3_2_1_, user2_.usercreate_id as usercreate6_2_1_, user2_.usermodify_id as usermodify7_2_1_, user2_.version as version2_1_, user2_.name as name2_1_, user3_.id as id2_2_, user3_.creationDate as creation2_2_2_, user3_.modificationDate as modifica3_2_2_, user3_.usercreate_id as usercreate6_2_2_, user3_.usermodify_id as usermodify7_2_2_, user3_.version as version2_2_, user3_.name as name2_2_, user4_.id as id2_3_, user4_.creationDate as creation2_2_3_, user4_.modificationDate as modifica3_2_3_, user4_.usercreate_id as usercreate6_2_3_, user4_.usermodify_id as usermodify7_2_3_, user4_.version as version2_3_, user4_.name as name2_3_, product5_.id as id0_4_, product5_.creationDate as creation2_0_4_, product5_.modificationDate as modifica3_0_4_, product5_.usercreate_id as usercreate7_0_4_, product5_.usermodify_id as usermodify8_0_4_, product5_.version as version0_4_, product5_.code as code0_4_, product5_.name as name0_4_, user6_.id as id2_5_, user6_.creationDate as creation2_2_5_, user6_.modificationDate as modifica3_2_5_, user6_.usercreate_id as usercreate6_2_5_, user6_.usermodify_id as usermodify7_2_5_, user6_.version as version2_5_, user6_.name as name2_5_, user7_.id as id2_6_, user7_.creationDate as creation2_2_6_, user7_.modificationDate as modifica3_2_6_, user7_.usercreate_id as usercreate6_2_6_, user7_.usermodify_id as usermodify7_2_6_, user7_.version as version2_6_, user7_.name as name2_6_ from ReceivingGoodDetail details0_ left outer join COMMON_USER user1_ on details0_.usercreate_id=user1_.id left outer join COMMON_USER user2_ on user1_.usercreate_id=user2_.id left outer join COMMON_USER user3_ on user2_.usermodify_id=user3_.id left outer join COMMON_USER user4_ on details0_.usermodify_id=user4_.id left outer join Product product5_ on details0_.product_id=product5_.id left outer join COMMON_USER user6_ on product5_.usercreate_id=user6_.id left outer join COMMON_USER user7_ on product5_.usermodify_id=user7_.id where details0_.receivinggood_id=? after adding try selecting the size : 5 after adding, now flushing Hibernate: update ReceivingGood set creationDate=?, modificationDate=?, usercreate_id=?, usermodify_id=?, version=?, purchaseorder_id=?, supplier_id=?, transactionDate=?, transactionNumber=?, transactionType=?, transactionYearMonth=?, warehouse_id=? where id=? and version=? detail size : 5 */ public void editLazyCollection() { String headerId = "3b373f6a-9cd1-4c9c-9d46-240de37f6b0f"; ReceivingGood receivingGood = em.find(ReceivingGood.class, headerId); // get existing detail ReceivingGoodDetail detail = em.find(ReceivingGoodDetail.class, "323fb0e7-9bb2-48dc-bc07-5ff32f30e131"); detail.setInternalUnit("MCB"); System.out.println("adding existing detail into lazy collection"); receivingGood.addReceivingGoodDetail(detail); System.out.println("after adding try selecting the size : " + receivingGood.getDetails().size()); System.out.println("after adding, now flushing"); em.flush(); System.out.println("detail size : " + receivingGood.getDetails().size()); } Please share your experience on this matter ! Thank you !

  Read the article

• SVN Server not responding

  - by Rob Forrest

  I've been bashing my head against a wall with this one all day and I would greatly appreciate a few more eyes on the problem at hand. We have an in-house SVN Server that contains all live and development code for our website. Our live server can connect to this and get updates from the repository. This was all working fine until we migrated the SVN Server from a physical machine to a vSphere VM. Now, for some reason that continues to fathom me, we can no longer connect to the SVN Server. The SVN Server runs CentOS 6.2, Apache and SVN 1.7.2. SELinux is well and trully disabled and the problem remains when iptables is stopped. Our production server does run an older version of CentOS and SVN but the same system worked previously so I don't think that this is the issue. Of note, if I have iptables enabled, using service iptables status, I can see a single packet coming in and being accepted but the production server simply hangs on any svn command. If I give up waiting and do a CTRL-C to break the process I get a "could not connect to server". To me it appears to be something to do with the SVN Server rejecting external connections but I have no idea how this would happen. Any thoughts on what I can try from here? Thanks, Rob Edit: Network topology Production server sits externally to our in-house SVN server. Our IPCop (?) firewall allows connections from it (and it alone) on port 80 and passes the connection to the SVN Server. The hardware is all pretty decent and I don't doubt that its doing its job correctly, especially as iptables is seeing the new connections. subversion.conf (in /etc/httpd/conf.d) LoadModule dav_svn_module modules/mod_dav_svn.so <Location /repos> DAV svn SVNPath /var/svn/repos <LimitExcept PROPFIND OPTIONS REPORT> AuthType Basic AuthName "SVN Server" AuthUserFile /var/svn/svn-auth Require valid-user </LimitExcept> </Location> ifconfig eth0 Link encap:Ethernet HWaddr 00:0C:29:5F:C8:3A inet addr:172.16.0.14 Bcast:172.16.0.255 Mask:255.255.255.0 inet6 addr: fe80::20c:29ff:fe5f:c83a/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:32317 errors:0 dropped:0 overruns:0 frame:0 TX packets:632 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:2544036 (2.4 MiB) TX bytes:143207 (139.8 KiB) netstat -lntp Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN 1484/mysqld tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN 1135/rpcbind tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN 1351/sshd tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN 1230/cupsd tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN 1575/master tcp 0 0 0.0.0.0:58401 0.0.0.0:* LISTEN 1153/rpc.statd tcp 0 0 0.0.0.0:5672 0.0.0.0:* LISTEN 1626/qpidd tcp 0 0 :::139 :::* LISTEN 1678/smbd tcp 0 0 :::111 :::* LISTEN 1135/rpcbind tcp 0 0 :::80 :::* LISTEN 1615/httpd tcp 0 0 :::22 :::* LISTEN 1351/sshd tcp 0 0 ::1:631 :::* LISTEN 1230/cupsd tcp 0 0 ::1:25 :::* LISTEN 1575/master tcp 0 0 :::445 :::* LISTEN 1678/smbd tcp 0 0 :::56799 :::* LISTEN 1153/rpc.statd iptables --list -v -n (when iptables is stopped) Chain INPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination iptables --list -v -n (when iptables is running, after one attempted svn connection) Chain INPUT (policy ACCEPT 68 packets, 6561 bytes) pkts bytes target prot opt in out source destination 19 1304 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 0 0 ACCEPT icmp -- * * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 1 60 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 0 0 ACCEPT udp -- * * 0.0.0.0/0 0.0.0.0/0 state NEW udp dpt:80 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 17 packets, 1612 bytes) pkts bytes target prot opt in out source destination tcpdump 17:08:18.455114 IP 'production server'.43255 > 'svn server'.local.http: Flags [S], seq 3200354543, win 5840, options [mss 1380,sackOK,TS val 2011458346 ecr 0,nop,wscale 7], length 0 17:08:18.455169 IP 'svn server'.local.http > 'production server'.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 816478 ecr 2011449346,nop,wscale 7], length 0 17:08:19.655317 IP 'svn server'.local.http > 'production server'k.43255: Flags [S.], seq 629885453, ack 3200354544, win 14480, options [mss 1460,sackOK,TS val 817679 ecr 2011449346,nop,wscale 7], length 0

  Read the article

• How to find an entry-level job after you already have a graduate degree?

  - by Uri

  Note: I asked this question in early 2009. A couple of months later, I found a great job. I've previously updated this question with some tips for whoever ends up in a similar situation, and now cleaned it up a little for the benefit of the fresh batch of graduates. Original post: In my early 20s I abandoned a great C++ development career path in a major company to go to graduate school and get a research masters (3 years). I did another year in industrial research, and then moved to the US to attend graduate school again, getting another masters and a Ph.D in software engineering from a top school (another 6 years down the drain). I was coding the whole way throughout my degrees (core Java and Eclipse plug-ins) and working on research related to software engineering (usability of APIs). I ended up graduating the year of the recession, with a son on the way and the prospects of no healthcare. Academic jobs and industrial research jobs are quite scarce. Initially, I was naive, thinking that with my background, I could easily find a coding job. Big mistake. It turns out that I'm in a complicated position. Entry level positions are usually offered to college undergraduates. I attended my school's career fairs, but you could immediately see signs of Ph.D. aversion and overqualification issues. Some of the recruiters I spoke with explicitly told me that they wanted 20 year olds with clean slates, and some were looking for interns since they are in various forms of hiring freezes. I managed to get a couple of interviews from these career fairs and through recruiters. However, since I've been out of school for a long time and programming primarily in Java, I am also no longer proficient in C/C++ and the usual range of college-level interview questions that everyone uses. I had no problems with this when I was 19 and interviewing for my first job since a lot of what you do in C is manipulate pointers and I was coding C++ for fun and for school. Later I was routinely doing pointer manipulation on the job, and during my first masters taught college courses with data structures and C++. But even though I remember many properties of C++ well, it's been close to ten years since I regularly used C++ and pointers. As a Java developer I rarely had to work at this level, but experience in OOD and in writing good maintainable code is meaningless for C++ interviews. Reading books as a refresh and looking at sample code did not do the trick. I also looked at mid-to-senior level Java positions, but most of them focused on J2EE APIs rather than on core Java and required a certain number of years in industrial positions. Coding research tools and prior C++ experience doesn't count. So that sends me back to entry-level jobs that are posted through job-boards, and these are not common (mostly they are Monster junk), and small companies are even less likely to answer a Ph.D. compared to the giants who participate in top-10 career fairs. Even worse, in many companies initial screening is done by HR folks who really don't want to deal with anything anomalous like a Ph.D. Any tips on how I should approach this intractable position? For example, what should I write in cover letters? Note that while immigration is not an issue for me, I cannot go freelance as I need the benefits (and in particular group health insurance). During my studies I had no time to contribute to open-source projects or maintain a popular blog, so even if I invested in that now there would be no immediate benefit. Updates: In the two months after posting this I received several offers to work as a core Java developer in the financial industry and accepted one from a firm where I am working to this day. For those who find themselves in similar situations, here are my tips: Give up on trying to find an entry level positions. You can't undo time. Accept the fact that there is Ph.D. discrimination in the job market (some might say rightfully so). It is legal to discriminate based on education. No point fighting it. The most important tip is to focus on the language you are comfortable with. The sad truth about programming in a particular language is that it is not like riding a bike. If you haven't used a language in the last few years, and can't actually apply it routinely (not just as a refresher) before you start your search, it is going to be very difficult to do well in an interview. Now that I'm interviewing others, I routinely see it in folks with a mixed C++/Java background. We maintain "a shadow" of the old language but end up with a weird mix that makes it hard to interview on either. Entry-level folks are at an advantage here since they usually have one language. Memory can help you do great in a screening interview, but without recent day-to-day experience, code tests will be difficult. Despite the supposed relation, core Java programming and J2EE programming are two different things with different skillsets. If you come from academia, you likely have very little J2EE experience and may find it hard to get accepted for a J2EE job. J2EE jobs seem to have a larger list of acronyms in their requirements. In addition, from interviewing J2EE developers it seems that for many there is a focus on mastering specific APIs and architectures, whereas core Java development tends to be secondary. In the same way that I can no longer manipulate pointers well, a J2EE developer may have difficulties doing low level Java manipulation. This puts you at a relative advantage in competing for core Java jobs! If you are able to work for startups (in terms of family life and stability) or migrate to startup-rich areas such as the west coast, you can find many exciting opportunities where advanced degrees are a benefit. I've since been approached by several startups, although I had to decline. Work through a recruiter if possible. They have direct contacts with the hiring parties, allowing you to "stand out". It is better to get a clear yes/no confirmation from a recruiter on whether a company might be interested in interviewing you, than it is to send your resume and hope that someone will ever see it. Recruiters are also a great way of bypassing HR. However, also beware of recruiters. They have a vested interest and will go to various shady practices and pressure tactics. To find a good recruiter, talk to a friend who declined a job offer he got through a recruiter. A good recruiter, to me, is measured in how they handle that. Interview for the jobs that require your core strength. If you're rusty or entirely unfamiliar with a technology around which the job revolves, you're probably not a good match. Yes, you probably have the talent to master them, but most companies would want "instant gratification". I got my offers from companies that wanted core Java developer. I didn't do well on places that wanted advance C++ because I am too rusty and not up to date on recent libraries. I also didn't hear from companies that wanted lots of J2EE experience, and that's ok. Finding companies that want core Java without web is harder, but exists in specific industries (e.g., finance, defense). This requires a lot more legwork in terms of search, but these jobs do exist. There are different interview styles. Some companies focus on puzzles, some companies focus on algorithms, and some companies focus on design and coding skills. I had the most success in places where the questions were the most related to the function I would have been performing. Pick companies accordingly as well.

  Read the article

• Help with this code.

  - by karthick6891

  Heading ##Hey guys i need help with this code.The short version is,i have to do match the follwing by using drag and drop in jquery and later i need to show a message whether it is right or wrong. var output = "Wrong"; var old_item ; var new_item ; var newObjArray=[]; $(function() { var $gallery = $('.gallery'), $trash = $('.trash'); $('div',$gallery).draggable({ revert: 'invalid', containment: 'document', helper: 'clone', cursor: 'move', }); // let the trash be droppable, accepting the gallery items $trash.droppable({ //accept: '#gallery div', //activeClass: 'ui-state-highlight', tolerance: 'touch', drop: function(ev, ui) { new_item = ui.draggable; $(this).droppable("option","activeClass",'.ui-state-highlight'); if(contains(newObjArray,ui.draggable)) { newObjArray.pop(ui.draggable); } newObjArray.push(ui.draggable); deleteImage(ui.draggable,$(this)); } }); // let the gallery be droppable as well, accepting items from the trash $gallery.droppable({ //accept: '#trash li', activeClass: 'custom-state-active', drop: function(ev, ui) { recycleImage(ui.draggable); } }); // image deletion function function deleteImage($item,element) { var $list; $item.fadeOut(10,function() { if($(".ui-widget-content", element).length <1){ old_item = $item; $list = $('<div class="gallery ui-helper-reset"/>').appendTo(element); //$('ul',$trash).length ? $('ul',$trash) : $('<ul class="gallery ui-helper-reset"/>').appendTo($trash); $item.appendTo($list).fadeIn(10); } else{ recycleImage($(".ui-widget-content",element)); $list = $('<div class="gallery ui-helper-reset"/>').appendTo(element); $item.appendTo($list).fadeIn(10); old_item = $item; } }); } //check for given answer // image recycle function function recycleImage($item) { $item.fadeOut(10,function() { $item.find("img").end().appendTo($gallery).fadeIn(10); }); } // image preview function, demonstrating the ui.dialog used as a modal window }); function checkOrder(){ if(newObjArray==null){ } else if(newObjArray!=null){ if(newObjArray[0].attr("id")=="5"&& newObjArray[1].attr("id")=="1" && newObjArray[2].attr("id")=="3" && newObjArray[3].attr("id")=="2" && newObjArray[4].attr("id")=="4"){ parent.parent.increaseCorrectA(); } else{ parent.parent.increaseWrongA(); } } } function contains(a, obj) { var i = a.length; while (i--) { if (a[i] === obj) { return true; } } return false; } I am calling the function checkOrder() from the html page after the matching of items is over.What happens here is i have just stored the user responses on the draggable over droppable in an array,based on it's position.It is a bad practice cause,i am saying whether it's right or wrong through its position in the array.The only thing i can do is get the draggable's id present in the droppable.But i dont know how to get that inside the function checkOrder().Any ideas please?

  Read the article

• MVC SiteMap - when different nodes point to same action SiteMap.CurrentNode does not map to the correct route

  - by awrigley

  Setup: I am using ASP.NET MVC 4, with mvcSiteMapProvider to manage my menus. I have a custom menu builder that evaluates whether a node is on the current branch (ie, if the SiteMap.CurrentNode is either the CurrentNode or the CurrentNode is nested under it). The code is included below, but essentially checks the url of each node and compares it with the url of the currentnode, up through the currentnodes "family tree". The CurrentBranch is used by my custom menu builder to add a class that highlights menu items on the CurrentBranch. The Problem: My custom menu works fine, but I have found that the mvcSiteMapProvider does not seem to evaluate the url of the CurrentNode in a consistent manner: When two nodes point to the same action and are distinguished only by a parameter of the action, SiteMap.CurrentNode does not seem to use the correct route (it ignores the distinguishing parameter and defaults to the first route that that maps to the action defined in the node). Example of the Problem: In an app I have Members. A Member has a MemberStatus field that can be "Unprocessed", "Active" or "Inactive". To change the MemberStatus, I have a ProcessMemberController in an Area called Admin. The processing is done using the Process action on the ProcessMemberController. My mvcSiteMap has two nodes that BOTH map to the Process action. The only difference between them is the alternate parameter (such are my client's domain semantics), that in one case has a value of "Processed" and in the other "Unprocessed": Nodes: <mvcSiteMapNode title="Process" area="Admin" controller="ProcessMembers" action="Process" alternate="Unprocessed" /> <mvcSiteMapNode title="Change Status" area="Admin" controller="ProcessMembers" action="Process" alternate="Processed" /> Routes: The corresponding routes to these two nodes are (again, the only thing that distinguishes them is the value of the alternate parameter): context.MapRoute( "Process_New_Members", "Admin/Unprocessed/Process/{MemberId}", new { controller = "ProcessMembers", action = "Process", alternate="Unprocessed", MemberId = UrlParameter.Optional } ); context.MapRoute( "Change_Status_Old_Members", "Admin/Members/Status/Change/{MemberId}", new { controller = "ProcessMembers", action = "Process", alternate="Processed", MemberId = UrlParameter.Optional } ); What works: The Html.ActionLink helper uses the routes and produces the urls I expect: @Html.ActionLink("Process", MVC.Admin.ProcessMembers.Process(item.MemberId, "Unprocessed") // Output (alternate="Unprocessed" and item.MemberId = 12): Admin/Unprocessed/Process/12 @Html.ActionLink("Status", MVC.Admin.ProcessMembers.Process(item.MemberId, "Processed") // Output (alternate="Processed" and item.MemberId = 23): Admin/Members/Status/Change/23 In both cases the output is correct and as I expect. What doesn't work: Let's say my request involves the second option, ie, /Admin/Members/Status/Change/47, corresponding to alternate = "Processed" and a MemberId of 47. Debugging my static CurrentBranch property (see below), I find that SiteMap.CurrentNode shows: PreviousSibling: null Provider: {MvcSiteMapProvider.DefaultSiteMapProvider} ReadOnly: false ResourceKey: "" Roles: Count = 0 RootNode: {Home} Title: "Process" Url: "/Admin/Unprocessed/Process/47" Ie, for a request url of /Admin/Members/Status/Change/47, SiteMap.CurrentNode.Url evaluates to /Admin/Unprocessed/Process/47. Ie, it is ignorning the alternate parameter and using the wrong route. CurrentBranch Static Property: /// <summary> /// ReadOnly. Gets the Branch of the Site Map that holds the SiteMap.CurrentNode /// </summary> public static List<SiteMapNode> CurrentBranch { get { List<SiteMapNode> currentBranch = null; if (currentBranch == null) { SiteMapNode cn = SiteMap.CurrentNode; SiteMapNode n = cn; List<SiteMapNode> ln = new List<SiteMapNode>(); if (cn != null) { while (n != null && n.Url != SiteMap.RootNode.Url) { // I don't need to check for n.ParentNode == null // because cn != null && n != SiteMap.RootNode ln.Add(n); n = n.ParentNode; } // the while loop excludes the root node, so add it here // I could add n, that should now be equal to SiteMap.RootNode, but this is clearer ln.Add(SiteMap.RootNode); // The nodes were added in reverse order, from the CurrentNode up, so reverse them. ln.Reverse(); } currentBranch = ln; } return currentBranch; } } The Question: What am I doing wrong? The routes are interpreted by Html.ActionLlink as I expect, but are not evaluated by SiteMap.CurrentNode as I expect. In other words, in evaluating my routes, SiteMap.CurrentNode ignores the distinguishing alternate parameter.

  Read the article

• Why is my mdadm raid-1 recovery so slow?

  - by dimmer

  On a system I'm running Ubuntu 10.04. My raid-1 restore started out fast but quickly became ridiculously slow (at this rate the restore will take 150 days!): dimmer@paimon:~$ cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid1 sdc1[2] sdb1[1] 1953513408 blocks [2/1] [_U] [====>................] recovery = 24.4% (477497344/1953513408) finish=217368.0min speed=113K/sec unused devices: <none> Eventhough I have set the kernel variables to reasonably quick values: dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_min 1000000 dimmer@paimon:~$ cat /proc/sys/dev/raid/speed_limit_max 100000000 I am using 2 2.0TB Western Digital Hard Disks, WDC WD20EARS-00M and WDC WD20EARS-00J. I believe they have been partitioned such that their sectors are aligned. dimmer@paimon:/sys$ sudo parted /dev/sdb GNU Parted 2.2 Using /dev/sdb Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00M (scsi) Disk /dev/sdb: 2000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 (parted) unit s (parted) p Number Start End Size File system Name Flags 1 2048s 3907028991s 3907026944s ext4 (parted) q dimmer@paimon:/sys$ sudo parted /dev/sdc GNU Parted 2.2 Using /dev/sdc Welcome to GNU Parted! Type 'help' to view a list of commands. (parted) p Model: ATA WDC WD20EARS-00J (scsi) Disk /dev/sdc: 2000GB Sector size (logical/physical): 512B/4096B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 2000GB 2000GB ext4 I am beginning to think that I have a hardware problem, otherwise I can't imagine why the mdadm restore should be so slow. I have done a benchmark on /dev/sdc using Ubuntu's disk utility GUI app, and the results looked normal so I know that sdc has the capability to write faster than this. I also had the same problem on a similar WD drive that I RMAd because of bad sectors. I suppose it's possible they sent me a replacement with bad sectors too, although there are no SMART values showing them yet. Any ideas? Thanks. As requested, output of top sorted by cpu usage (notice there is ~0 cpu usage). iowait is also zero which seems strange: top - 11:35:13 up 2 days, 9:40, 3 users, load average: 2.87, 2.58, 2.30 Tasks: 142 total, 1 running, 141 sleeping, 0 stopped, 0 zombie Cpu(s): 0.0%us, 0.2%sy, 0.0%ni, 99.8%id, 0.0%wa, 0.0%hi, 0.0%si, 0.0%st Mem: 3096304k total, 1482164k used, 1614140k free, 617672k buffers Swap: 1526132k total, 0k used, 1526132k free, 535416k cached PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 45 root 20 0 0 0 0 S 0 0.0 2:17.02 scsi_eh_0 1 root 20 0 2808 1752 1204 S 0 0.1 0:00.46 init 2 root 20 0 0 0 0 S 0 0.0 0:00.00 kthreadd 3 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/0 4 root 20 0 0 0 0 S 0 0.0 0:00.17 ksoftirqd/0 5 root RT 0 0 0 0 S 0 0.0 0:00.00 watchdog/0 6 root RT 0 0 0 0 S 0 0.0 0:00.02 migration/1 ... dmesg errors, definitely looking like hardware: [202884.000157] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [202884.007015] ata5.00: failed command: FLUSH CACHE EXT [202884.013728] ata5.00: cmd ea/00:00:00:00:00/00:00:00:00:00/a0 tag 0 [202884.013730] res 40/00:00:ff:59:2e/00:00:35:00:00/e0 Emask 0x4 (timeout) [202884.033667] ata5.00: status: { DRDY } [202884.040329] ata5: hard resetting link [202889.400050] ata5: link is slow to respond, please be patient (ready=0) [202894.048087] ata5: COMRESET failed (errno=-16) [202894.054663] ata5: hard resetting link [202899.412049] ata5: link is slow to respond, please be patient (ready=0) [202904.060107] ata5: COMRESET failed (errno=-16) [202904.066646] ata5: hard resetting link [202905.840056] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [202905.849178] ata5.00: configured for UDMA/133 [202905.849188] ata5: EH complete [203899.000292] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [203899.007096] ata5.00: failed command: IDENTIFY DEVICE [203899.013841] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [203899.013843] res 40/00:00:ff:f9:f6/00:00:38:00:00/e0 Emask 0x4 (timeout) [203899.041232] ata5.00: status: { DRDY } [203899.048133] ata5: hard resetting link [203899.816134] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [203899.826062] ata5.00: configured for UDMA/133 [203899.826079] ata5: EH complete [204375.000200] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204375.007421] ata5.00: failed command: IDENTIFY DEVICE [204375.014799] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204375.014800] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204375.044374] ata5.00: status: { DRDY } [204375.051842] ata5: hard resetting link [204380.408049] ata5: link is slow to respond, please be patient (ready=0) [204384.440076] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204384.449938] ata5.00: configured for UDMA/133 [204384.449955] ata5: EH complete [204395.988135] ata5.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen [204395.988140] ata5.00: failed command: IDENTIFY DEVICE [204395.988147] ata5.00: cmd ec/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in [204395.988149] res 40/00:00:ff:0c:0f/00:00:39:00:00/e0 Emask 0x4 (timeout) [204395.988151] ata5.00: status: { DRDY } [204395.988156] ata5: hard resetting link [204399.320075] ata5: SATA link up 3.0 Gbps (SStatus 123 SControl 300) [204399.330487] ata5.00: configured for UDMA/133 [204399.330503] ata5: EH complete

  Read the article

• Mysql - Help me alter this search query involving multiple joins and conditions to get the desired r

  - by sandeepan-nath

  About the system - We are following tags based search. Tutors create packs - tag relations for tutors stored in tutors_tag_relations and those for packs stored in learning_packs_tag_relations. All tags are stored in tags table. The system has 6 tables - tutors, Users (linked to tutor_details), learning_packs, learning_packs_tag_relations, tutors_tag_relations and tags Please run the following fresh queries to setup the system :- CREATE TABLE IF NOT EXISTS learning_packs_tag_relations ( id_tag int(10) unsigned NOT NULL DEFAULT '0', id_tutor int(10) DEFAULT NULL, id_lp int(10) unsigned DEFAULT NULL, KEY Learning_Packs_Tag_Relations_FKIndex1 (id_tag), KEY id_lp (id_lp), KEY id_tag (id_tag) ) ENGINE=InnoDB DEFAULT CHARSET=latin1; CREATE TABLE IF NOT EXISTS learning_packs ( id_lp int(10) unsigned NOT NULL AUTO_INCREMENT, id_status int(10) unsigned NOT NULL DEFAULT '2', id_author int(10) unsigned NOT NULL DEFAULT '0', name varchar(255) NOT NULL DEFAULT '', PRIMARY KEY (id_lp) ) ENGINE=InnoDB DEFAULT CHARSET=utf8 AUTO_INCREMENT=21 ; CREATE TABLE IF NOT EXISTS tutors_tag_relations ( id_tag int(10) unsigned NOT NULL DEFAULT '0', id_tutor int(10) DEFAULT NULL, KEY Tutors_Tag_Relations (id_tag), KEY id_tutor (id_tutor), KEY id_tag (id_tag) ) ENGINE=InnoDB DEFAULT CHARSET=latin1; CREATE TABLE IF NOT EXISTS users ( id_user int(10) unsigned NOT NULL AUTO_INCREMENT, name varchar(100) NOT NULL DEFAULT '', surname varchar(155) NOT NULL DEFAULT '', PRIMARY KEY (id_user) ) ENGINE=InnoDB DEFAULT CHARSET=utf8 AUTO_INCREMENT=52 ; CREATE TABLE IF NOT EXISTS tutor_details ( id_tutor int(10) NOT NULL AUTO_INCREMENT, id_user int(10) NOT NULL, PRIMARY KEY (id_tutor) ) ENGINE=InnoDB DEFAULT CHARSET=latin1 AUTO_INCREMENT=60 ; CREATE TABLE IF NOT EXISTS tags ( id_tag int(10) unsigned NOT NULL AUTO_INCREMENT, tag varchar(255) DEFAULT NULL, PRIMARY KEY (id_tag), UNIQUE KEY tag (tag) ) ENGINE=InnoDB DEFAULT CHARSET=latin1 AUTO_INCREMENT=5 ; ALTER TABLE learning_packs_tag_relations ADD CONSTRAINT Learning_Packs_Tag_Relations_ibfk_1 FOREIGN KEY (id_tag) REFERENCES tags (id_tag) ON DELETE NO ACTION ON UPDATE NO ACTION; ALTER TABLE learning_packs ADD CONSTRAINT Learning_Packs_ibfk_2 FOREIGN KEY (id_author) REFERENCES users (id_user) ON DELETE NO ACTION ON UPDATE NO ACTION; ALTER TABLE tutors_tag_relations ADD CONSTRAINT Tutors_Tag_Relations_ibfk_1 FOREIGN KEY (id_tag) REFERENCES tags (id_tag) ON DELETE NO ACTION ON UPDATE NO ACTION; INSERT INTO test.users ( id_user , name , surname ) VALUES ( NULL , 'Vivian', 'Richards' ), ( NULL , 'Sachin', 'Tendulkar' ); INSERT INTO test.users ( id_user , name , surname ) VALUES ( NULL , 'Don', 'Bradman' ); INSERT INTO test.tutor_details ( id_tutor , id_user ) VALUES ( NULL , '52' ), ( NULL , '53' ); INSERT INTO test.tutor_details ( id_tutor , id_user ) VALUES ( NULL , '54' ); INSERT INTO test.tags ( id_tag , tag ) VALUES ( 1 , 'Vivian' ), ( 2 , 'Richards' ); INSERT INTO test.tags (id_tag, tag) VALUES (3, 'Sachin'), (4, 'Tendulkar'); INSERT INTO test.tags (id_tag, tag) VALUES (5, 'Don'), (6, 'Bradman'); INSERT INTO test.learning_packs (id_lp, id_status, id_author, name) VALUES ('1', '1', '52', 'Cricket 1'), ('2', '2', '52', 'Cricket 2'); INSERT INTO test.tags (id_tag, tag) VALUES ('7', 'Cricket'), ('8', '1'); INSERT INTO test.tags (id_tag, tag) VALUES ('9', '2'); INSERT INTO test.learning_packs_tag_relations (id_tag, id_tutor, id_lp) VALUES ('7', '52', '1'), ('8', '52', '1'); INSERT INTO test.learning_packs_tag_relations (id_tag, id_tutor, id_lp) VALUES ('7', '52', '2'), ('9', '52', '2'); =================================================================================== Requirement Now I want to search learning_packs, with the same AND logic. Help me modify the following query so that searching pack name or tutor's name, surname results all active packs (either directly those packs or packs created by those tutors). ================================================================================== select lp.* from Learning_Packs AS lp LEFT JOIN Learning_Packs_Tag_Relations AS lptagrels ON lp.id_lp = lptagrels.id_lp LEFT JOIN Tutors_Tag_Relations as ttagrels ON lp.id_author = ttagrels.id_tutor LEFT JOIN Tutor_Details AS td ON ttagrels.id_tutor = td.id_tutor LEFT JOIN Users as u on td.id_user = u.id_user JOIN Tags as t on (t.id_tag = lptagrels.id_tag) or (t.id_tag = ttagrels.id_tag) where lp.id_status = 1 AND ( t.tag LIKE "%Vivian%" OR t.tag LIKE "%Richards%" ) group by lp.id_lp HAVING count(lp.id_lp) 1 limit 0,20 As you can see, searching "Cricket 1" returns that pack but searching Vivian Richards does not return the same pack. Please help

  Read the article

• Blogger issue with custom background images on Chrome and Safari

  - by hdx

  This is weird, the site in question is blog.andrebatista.info and it is a hosted at blogger.com. I'm trying to make the blogger template look the same as the one in my main website, www.andrebatista.info. For some reason if I go directly to the blog address Chrome and Safari fail to display all of my background images... all of them. However if I first go to www.andrebatista.info first and then go to the blog it renders just fine ?¿ The way I'm customizing it is by adding a link to my main site's stylesheet at the very end of the head tag on the blogger template. That stylesheet is displayed below: *{ margin:0; padding:0; border:0; } html,body { background:#064169 url(http://www.andrebatista.info/images/main_gradient_slice.jpg) repeat-x; font-family: Arial, "MS Trebuchet", sans-serif; font-size:18px; } #main_wrapper{ margin: 0 auto; width:1024px; } #header{ background: url(http://www.andrebatista.info/images/header.jpg); height:133px; border:none; margin:0; } #menu_wrapper{ background: url(http://www.andrebatista.info/images/menu.jpg); height:34px; overflow:hidden; } #menu_wrapper .menu_item{ color:white; float: left; border: 1 px solid red; height: 34px; padding-top:10px; text-align:center; width:100px; } #menu_wrapper .first{ padding-left:240px; float:left; width:100px; } #menu_wrapper .active,#menu_wrapper .menu_item:hover{ background-color:white; color:Teal; cursor: pointer; } #content_area_wrapper{ background: url(http://www.andrebatista.info/images/body_bg_slice.jpg) repeat-y; } #content_area{ min-height:524px; background: url(http://www.andrebatista.info/images/main_content_top.jpg) repeat-x; } #main_banner{ background: url(http://www.andrebatista.info/images/main_banner.jpg) no-repeat center center; width:662px; height:338px; margin: 0 auto; } #main_banner div{ color:white; padding-left:47px; padding-right:164px; padding-top:105px; } #text_area{ overflow:hidden; width:662px; margin:0 auto; padding:14px; } #contentList{ padding:0 20px 20px 20px; } #text_area .left{ width:50%; float:left; } #text_area .left{ width:50%; float:right; } #footer2{ background: url(http://www.andrebatista.info/images/footer.jpg); height:62px; } #footer{ background: url(http://www.andrebatista.info/images/footer.jpg); height:62px; } Any ideas on what I could be missing?

  Read the article

• Perl: Deleting multiple re-occuring lines where a certain criteria is met

  - by george-lule

  Dear all, I have data that looks like below, the actual file is thousands of lines long. Event_time Cease_time Object_of_reference -------------------------- -------------------------- ---------------------------------------------------------------------------------- Apr 5 2010 5:54PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSJN1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=LUGALAMBO_900 Apr 5 2010 5:55PM Apr 5 2010 6:43PM SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSJN1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=LUGALAMBO_900 Apr 5 2010 5:58PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA Apr 5 2010 5:58PM Apr 5 2010 6:01PM SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA Apr 5 2010 6:01PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA Apr 5 2010 6:03PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSJN1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=KAPKWAI_900 Apr 5 2010 6:03PM Apr 5 2010 6:04PM SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSJN1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=KAPKWAI_900 Apr 5 2010 6:04PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSJN1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=KAPKWAI_900 Apr 5 2010 6:03PM Apr 5 2010 6:03PM SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA Apr 5 2010 6:03PM NULL SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA Apr 5 2010 6:03PM Apr 5 2010 7:01PM SubNetwork=ONRM_RootMo,SubNetwork=AXE,ManagedElement=BSCC1,BssFunction= BSS_ManagedFunction,BtsSiteMgr=BULAGA As you can see, each file has a header which describes what the various fields stand for(event start time, event cease time, affected element). The header is followed by a number of dashes. My issue is that, in the data, you see a number of entries where the cease time is NULL i.e event is still active. All such entries must go i.e for each element where the alarm cease time is NULL, the start time, the cease time(in this case NULL) and the actual element must be deleted from the file. In the remaining data, all the text starting from word SubNetwork upto BtsSiteMgr= must also go. Along with the headers and the dashes. Final output should look like below: Apr 5 2010 5:55PM Apr 5 2010 6:43PM LUGALAMBO_900 Apr 5 2010 5:58PM Apr 5 2010 6:01PM BULAGA Apr 5 2010 6:03PM Apr 5 2010 6:04PM KAPKWAI_900 Apr 5 2010 6:03PM Apr 5 2010 6:03PM BULAGA Apr 5 2010 6:03PM Apr 5 2010 7:01PM BULAGA Below is a Perl script that I have written. It has taken care of the headers, the dashes, the NULL entries but I have failed to delete the lines following the NULL entries so as to produce the above output. #!/usr/bin/perl use strict; use warnings; $^I=".bak" #Backup the file before messing it up. open (DATAIN,"<george_perl.txt")|| die("can't open datafile: $!"); # Read in the data open (DATAOUT,">gen_results.txt")|| die("can't open datafile: $!"); #Prepare for the writing while (<DATAIN>) { s/Event_time//g; s/Cease_time//g; s/Object_of_reference//g; s/\-//g; #Preceding 4 statements are for cleaning out the headers my $theline=$_; if ($theline =~ /NULL/){ next; next if $theline =~ /SubN/; } else{ print DATAOUT $theline; } } close DATAIN; close DATAOUT; Kindly help point out any modifications I need to make on the script to make it produce the necessary output. Will be very glad for your help Kind regards George.

  Read the article

• Rendering a Long Document on iPad

  - by benjismith

  I'm implementing a document viewer with highlighting/annotation capabilities for a custom document format on iPad. The documents are kind of long (100 to 200 pages, if printed on paper) and I've had a hard time finding the right approach. Here are the requirments: 1) Basic rich-text styling: control of left/right margins. Control of font name, size, foreground/background color, and line spacing. Bold, italics, underline, etc. 2) Selection and highlighting of arbitrary text regions (not limited to paragraph boundaries, like in Safari/UIWebView). 3) Customization of the Cut/Copy/Paste popup (what is that thing called anyhow? UIActionBar?) This is one of the essential requirements of the app. My first implementation was based on UIWebView. I just rendered the document as HTML with CSS for text styling. But I couldn't get the kind of text selection behavior I wanted (across paragraph boundaries) and the UIActionBar can't be customized from within UIWebView. So I started working on a javascript approach, faking the device text-selection behavior using JQuery to trap touch events and dynamically modifying the DOM to change the background color of selected regions of text. I built a fake UIActionBar control as a hidden DIV, positioning it and unhiding it whenever there was an active selection region. Not too shabby. The main problem is that it's SLOOOOOOOW. Scrolling through the document is nice and quick, but dynamically changing the DOM is not very snappy. Plus, I couldn't figure out how to recreate the magnifier loupe, so my fake text-selection GUI doesn't look quite the same as the native implementation. Also, I haven't yet implemented the communication bridge between the javascript layer and the objective-c layer (where the rest of the app lives), but it was shaping up to be a huge hassle. So I've been looking at CoreText, but there are precious few examples on the web. I spent a little time with this simple little demo: http://github.com/jonasschnelli/I7CoreTextExample/ It shows how to use CoreText to draw an NSAttributedText string into a UIView. But it has its own problems: It doesn't implement text-selection behavior, and it doesn't present a UIActionBar, so I don't have any idea how to make that happen. And, more importantly, it tries to draw the entire document all at once, with significant performance degradations for long documents. My documents can have thousands of paragraphs, and less than 1% of the document is ever on screen at a time. On the plus side, these documents already contain precise formatting information. I know the exact page-position of every line of text, so I don't need a layout engine. Does anyone know how to implement this sort of view using CoreText? I understand that a full-fledged implementation is overkill for a question like this, but I'm looking for a good CoreText example with a few basic requirements: 1) Precise layout & formatting control (using the formatting metrics and text styles I've already calculated). 2) Arbitrary selection of text. 3) Customization of the UIActionBar. 4) Efficient recycling of resources for off-screen objects. I'd be happy to implement my own recycling when text elements scroll off-screen, but wouldn't that require re-implementing UIScrollView? I'm brand-new to iPhone development, and still getting used to Objective-C, but I've been working in other languages (Java, C#, flex/actionscript, etc) for more than ten years, so I feel confident in my ability to get the work done, if only I had a better feel for the iPhone SDK and the common coding patterns for stuff like this. Is it just me, or does the SDK documentation really suck? Anyhow, thanks for your help!

  Read the article

• My server app works strangely. What could be the reason(s)?

  - by Poni

  Hi! I've written a server app (two parts actually; proxy server and a game server) using C++ (board game). It uses IOCP as the sockets interface. For that app I've also written a "client simulator" (hereafter "client") app that spawns many client connections, where each of them plays, in very high speed, getting the CPU to be 100% utilized. So, that's how it goes in terms of topology: Game server - holds the game state. Real players do not connect it directly but through the proxy server. When a player joins a game, the proxy actually asks for it on behalf of that player, and the game server spawns a "player instance" for that player, and from now on, every notification between the game server and the player is being passed through the proxy. Proxy server - holds TCP connections with the real players. Players communicate with the game server through it only. Client simulator - connects to the proxy only. When running the server (again, it's actually two server apps) & client locally it all works just fine. I'm talking about 40k+ player instances in which all of them are active in a game. On the other hand, when running the server remotely with, say, 1000 clients who play things getting strange. For example, I run it as said above. Then with Task Manager I kill the client simulator app ("End Process Tree"). Then it seems like the buffer of the remote server got modified by another thread, or in other words, a memory corruption has been occurred. The server crashes because it got an unknown message id (it's a custom protocol where each message has it's own unique number). To make things clear, here is how I run the apps: PC1 - game server and clients simulator (because the clients will connect the proxy). PC2 - proxy server. The strangest thing is this: Only the remote side gets "corrupted". Remote in terms that it's not the PC I use to code the app (VC++ 2008). Let's call the PC I use to code the apps "PC1". Now for example, if this time I ran the game server on PC1 (it means that proxy server on PC2 and clients simulator on PC1), then the proxy server crashes with an "unknown message id" error. Another variation is when I run the proxy server on PC1 (again, the dev machine), the game server and the clients simulator on PC2, then the game server on PC2 gets crashed. As for the IOCP config: The servers' internal connections use the default receive/send buffer sizes. Tried even with setting them to 1MB, but no luck. I have three PCs in total; 2 x Vista 64bit <<-- one of those is the dev machine. The other is connected through WiFi. 1 x WinXP 32bit They're all connected in a "full duplex" manner. What could be the reason? Tried about everything; Stack tracing, recording some actions (like read/write logging).. I want to stress that only the PC I'm not using to code the apps crashes (actually the server app "role" which is running on it - sometimes the game server and sometimes the proxy server). At first I thought that maybe the wireless PC has problems (it's wireless..) but: TCP has it's own mechanisms to make sure the packet is delivered properly. Also, a crash also happens when trying it with the two PCs that are physically connected (Vista vs. XP). Another option is that the Windows DLLs versions might have problems, but then again, one of the tests is Vista vs. Vista, and the other is Vista vs. XP. Any idea?

  Read the article

• Unnecessary Java context switches

  - by Paul Morrison

  I have a network of Java Threads (Flow-Based Programming) communicating via fixed-capacity channels - running under WindowsXP. What we expected, based on our experience with "green" threads (non-preemptive), would be that threads would switch context less often (thus reducing CPU time) if the channels were made bigger. However, we found that increasing channel size does not make any difference to the run time. What seems to be happening is that Java decides to switch threads even though channels aren't full or empty (i.e. even though a thread doesn't have to suspend), which costs CPU time for no apparent advantage. Also changing Thread priorities doesn't make any observable difference. My question is whether there is some way of persuading Java not to make unnecessary context switches, but hold off switching until it is really necessary to switch threads - is there some way of changing Java's dispatching logic? Or is it reacting to something I didn't pay attention to?! Or are there other asynchronism mechanisms, e.g. Thread factories, Runnable(s), maybe even daemons (!). The answer appears to be non-obvious, as so far none of my correspondents has come up with an answer (including most recently two CS profs). Or maybe I'm missing something that's so obvious that people can't imagine my not knowing it... I've added the send and receive code here - not very elegant, but it seems to work...;-) In case you are wondering, I thought the goLock logic in 'send' might be causing the problem, but removing it temporarily didn't make any difference. I have added the code for send and receive... public synchronized Packet receive() { if (isDrained()) { return null; } while (isEmpty()) { try { wait(); } catch (InterruptedException e) { close(); return null; } if (isDrained()) { return null; } } if (isDrained()) { return null; } if (isFull()) { notifyAll(); // notify other components waiting to send } Packet packet = array[receivePtr]; array[receivePtr] = null; receivePtr = (receivePtr + 1) % array.length; //notifyAll(); // only needed if it was full usedSlots--; packet.setOwner(receiver); if (null == packet.getContent()) { traceFuncs("Received null packet"); } else { traceFuncs("Received: " + packet.toString()); } return packet; } synchronized boolean send(final Packet packet, final OutputPort op) { sender = op.sender; if (isClosed()) { return false; } while (isFull()) { try { wait(); } catch (InterruptedException e) { indicateOneSenderClosed(); return false; } sender = op.sender; } if (isClosed()) { return false; } try { receiver.goLock.lockInterruptibly(); } catch (InterruptedException ex) { return false; } try { packet.clearOwner(); array[sendPtr] = packet; sendPtr = (sendPtr + 1) % array.length; usedSlots++; // move this to here if (receiver.getStatus() == StatusValues.DORMANT || receiver.getStatus() == StatusValues.NOT_STARTED) { receiver.activate(); // start or wake up if necessary } else { notifyAll(); // notify receiver // other components waiting to send to this connection may also get // notified, // but this is handled by while statement } sender = null; Component.network.active = true; } finally { receiver.goLock.unlock(); } return true; }

  Read the article

• Perl not closing TCP sockets if clients are no longer connected?

  - by LM

  The purpose of the application is to listen for a specific UDP multicast and then to forward the data to any TCP clients connected to the server. The code works fine, but I have a problem with the sockets not closing after the TCP clients disconnects. A socketsniffer utility shows the the sockets remain open and all the UDP data continues to be forwarded to the clients. The problem I believe is with the "if ($write-connected())" block as it always return true, even if the TCP client is no longer connected. I use standard Windows Telnet to connect to the server and to see the data. When I close telnet, the TCP socket is suppose to close on the server. Any reason why connected() show the connections as active even if they are not? Also, what alternative should I use then? Code: #!/usr/bin/perl use IO::Socket::Multicast; use IO::Socket; use IO::Select; my $tcp_port = "4550"; my $tcp_socket = IO::Socket::INET->new( Listen => SOMAXCONN, LocalAddr => '0.0.0.0', LocalPort => $tcp_port, Proto => 'tcp', ReuseAddr => 1, ); use Socket qw(IPPROTO_TCP TCP_NODELAY); setsockopt( $tcp_socket, IPPROTO_TCP, TCP_NODELAY, 1); use constant GROUP => '239.2.0.81'; use constant PORT => '6550'; my $udp_socket= IO::Socket::Multicast->new(Proto=>'udp',LocalPort=>PORT); $udp_socket->mcast_add(GROUP) || die "Couldn't set group: $!\n"; my $read_select = IO::Select->new(); my $write_select = IO::Select->new(); $read_select->add($tcp_socket); $read_select->add($udp_socket); ## Loop forever, reading data from the UDP socket and writing it to the ## TCP socket(s). while (1) { ## No timeout specified (see docs for IO::Select). This will block until a TCP ## client connects or we have data. my @read = $read_select->can_read(); foreach my $read (@read) { if ($read == $tcp_socket) { ## Handle connect from TCP client. Note that UDP connections are ## stateless (no accept necessary)... my $new_tcp = $read->accept(); $write_select->add($new_tcp); } elsif ($read == $udp_socket) { ## Handle data received from UDP socket... my $recv_buffer; $udp_socket->recv($recv_buffer, 1024, undef); ## Write the data read from UDP out to the TCP client(s). Again, no ## timeout. This will block until a TCP socket is writable. my @write = $write_select->can_write(); foreach my $write (@write) { ## Make sure the socket is still connected before writing. if ($write->connected()) { $write->send($recv_buffer); } else { $write_select->remove($write); close $write; } } } } }

  Read the article

• Different setter behavior between DbContext and ObjectContext

  - by Paul

  (This is using EntityFramework 4.2 CTP) I haven't found any references to this on the web yet, although it's likely I'm using the wrong terminology while searching. There's also a very likely scenario where this is 100% expected behavior, just looking for confirmation and would rather not dig through the tt template (still new to this). Assuming I have a class with a boolean field called Active and I have one row that already has this value set to true. I have code that executes to set said field to True regardless of it's existing value. If I use DbContext to update the value to True no update is made. If I use ObjectContext to update the value an update is made regardless of the existing value. This is happening in the exact same EDMX, all I did was change the code generation template from DbContext to EntityObject. Update: Ok, found the confirmation I was looking for...consider this a dupe...next time I'll do MOAR SEARCHING! Entity Framework: Cancel a property change if no change in value ** Update 2: ** Problem: the default tt template wraps the "if (this != value)" in the setter with "if (iskey), so only primarykey fields receive this logic. Solution: it's not the most graceful thing, but I removed this check...we'll see how it pans out in real usage. I included the entire tt template, my changes are denoted with "**"... //////// //////// Write SimpleType Properties. //////// private void WriteSimpleTypeProperty(EdmProperty simpleProperty, CodeGenerationTools code) { MetadataTools ef = new MetadataTools(this); #> /// <summary> /// <#=SummaryComment(simpleProperty)#> /// </summary><#=LongDescriptionCommentElement(simpleProperty, 1)#> [EdmScalarPropertyAttribute(EntityKeyProperty= <#=code.CreateLiteral(ef.IsKey(simpleProperty))#>, IsNullable=<#=code.CreateLiteral(ef.IsNullable(simpleProperty))#>)] [DataMemberAttribute()] <#=code.SpaceAfter(NewModifier(simpleProperty))#><#=Accessibility.ForProperty(simpleProperty)#> <#=MultiSchemaEscape(simpleProperty.TypeUsage, code)#> <#=code.Escape(simpleProperty)#> { <#=code.SpaceAfter(Accessibility.ForGetter(simpleProperty))#>get { <#+ if (ef.ClrType(simpleProperty.TypeUsage) == typeof(byte[])) { #> return StructuralObject.GetValidValue(<#=code.FieldName(simpleProperty)#>); <#+ } else { #> return <#=code.FieldName(simpleProperty)#>; <#+ } #> } <#=code.SpaceAfter(Accessibility.ForSetter((simpleProperty)))#>set { <#+ **//if (ef.IsKey(simpleProperty)) **//{ if (ef.ClrType(simpleProperty.TypeUsage) == typeof(byte[])) { #> if (!StructuralObject.BinaryEquals(<#=code.FieldName(simpleProperty)#>, value)) <#+ } else { #> if (<#=code.FieldName(simpleProperty)#> != value) <#+ } #> { <#+ PushIndent(CodeRegion.GetIndent(1)); **//} #> <#=ChangingMethodName(simpleProperty)#>(value); ReportPropertyChanging("<#=simpleProperty.Name#>"); <#=code.FieldName(simpleProperty)#> = <#=CastToEnumType(simpleProperty.TypeUsage, code)#>StructuralObject.SetValidValue(<#=CastToUnderlyingType(simpleProperty.TypeUsage, code)#>value<#=OptionalNullableParameterForSetValidValue(simpleProperty, code)#>, "<#=simpleProperty.Name#>"); ReportPropertyChanged("<#=simpleProperty.Name#>"); <#=ChangedMethodName(simpleProperty)#>(); <#+ //if (ef.IsKey(simpleProperty)) //{ PopIndent(); #> } <#+ //} #> } }

  Read the article

• How do I get my snapshots in Nexus to appear in the m2eclipse dependency search?

  - by Brabster

  Hi, I've been working through the Nexus guide this weekend and I've got everything set up, to the point that I can publish a snapshot to my local nexus install. I can't seem to work out how to get m2eclipse to see the snapshot and offer it as an option in the Add Dependencies search panel. How do I do that? Thanks! In case it's of any use, my settings.xml is as follows: <settings xmlns="http://maven.apache.org/SETTINGS/1.0.0" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance" xsi:schemaLocation="http://maven.apache.org/SETTINGS/1.0.0 http://maven.apache.org/xsd/settings-1.0.0.xsd"> <localRepository /> <interactiveMode /> <usePluginRegistry /> <offline /> <pluginGroups /> <servers> <server> <id>localSnap</id> <username>deployment</username> <password>*****</password> </server> </servers> <mirrors> <mirror> <!--This sends everything else to /public --> <id>nexus</id> <mirrorOf>*</mirrorOf> <url>http://localhost:8080/nexus/content/groups/public</url> </mirror> </mirrors> <profiles> <profile> <id>nexus</id> <!--Enable snapshots for the built in central repo to direct --> <!--all requests to nexus via the mirror --> <repositories> <repository> <id>central</id> <url>http://central</url> <releases> <enabled>true</enabled> </releases> <snapshots> <enabled>true</enabled> </snapshots> </repository> </repositories> <pluginRepositories> <pluginRepository> <id>central</id> <url>http://central</url> <releases> <enabled>true</enabled> </releases> <snapshots> <enabled>true</enabled> </snapshots> </pluginRepository> </pluginRepositories> </profile> </profiles> <activeProfiles> <!--make the profile active all the time --> <activeProfile>nexus</activeProfile> </activeProfiles> </settings>

  Read the article

< Previous Page | 301 302 303 304 305 306 307 308 309 310 311 312  | Next Page >