Search Results

Search found 9889 results on 396 pages for 'pointer speed'.

Page 308/396 | < Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• Minecraft server hosting hardware specifications [on hold]

  - by Andrew Wright

  I am planning on purchasing a server to rent off Minecraft game servers, largely to friends. I am planning on purchasing a 128GB RAM server to save on colocation costs (as I am likely to need more than 32GB and would have to rent 2U of space...) I am hoping for some advice about the processing power needed to deal with this level of RAM. The servers will be run in a shared environment on linux in a VM to make backups easier. The server I have in mind is dual CPU. I have been considering at the low end dual Xeon E5-2609V2 Quad-Core 2.5Ghz, and at the high end dual Xeon E5-2650V2 Eight-Core 2.6Ghz. The difference between these is 6.4 GT/s and 8 GT/s and £3000 for the lower spec server, £4300 for the higher spec. I was hoping I could get advice about whether it is worth paying for the extra/higher speed processor or if I would be wasting my money? Thank you for any help - I appreciate that this is not directly related to professional system administration.

  Read the article

• Windows XP VM on VMWare ESXi 4.1 "pausing" / blocked occasionally

  - by FelixD

  We have an issue with Windows XP SP3 VMs on VMWare ESXi 4.1.0 (the free version): They sometimes seem to "pause" for several minutes. This happens rarely (maybe once a month per VM, at least noticed only that often), but still is an issue for us. It happens for three different but similar VMs on three pretty different hosts (different hardware). I have the feeling that the "pausing" is not actually the CPU blocking, but probably the harddisks, but not 100% sure. The servers have one IDE disk (C:) and one SCSI (D:) and it might be either of the two. I have seen scheduled tasks simply not starting for up to 9 minutes and then running normally again with normal speed. They were totally blocked. This is not a load issue, the VMWare hosts have average load and the VMs in question already have reserved CPU resources plus high priorities for CPU and disk. The Windows boxes run mainly MySQL, Tomcat, FileZilla server, Cygwin stuff, Java + R applications, VMWare client, Elusiva Terminal Server pro, Nagios client. Not sure if this might be related with any of that software (e.g. Elusiva). Trying to debug this, there was nothing visible in Windows Event log, other logs in C:\Windows, VMWare events etc. Unfortunately the vmware.log file ends with "Log throttled". We found that we ran into 2 VMWare bugs there: The VMWare client writes lots on bogus messages in the vmware.log, which we now disabled (log level error setting) plus the bug that VMWare does not unthrottle the log (at least so far despite VM reboots). I know there is not much guidance and that may also be the reason why I so far didn't find anything related on the web or on ServerFault, but maybe some of this rings a bell with someone? Or please direct me to what more info to post. I hope that the vmware.logs get unthrottled eventually (can't easily restart the hosts at the moment). Thanks for any input!

  Read the article

• 5 year old server upgrade

  - by rizzo0917

  I am looking to upgrade a server for a web app. Currently the application is running very sluggish. We've made some adjustments to mysql (that's another issue in itself) and made some adjustments so that heaviest quires get run on a copy of the database on another server was have as a backup, however this will not last that much longer and we are looking to upgrade. Currently the servers CPUs are (4) Intel(R) XEON(TM) CPU 2.00GHz, with 1 gig of ram. The database is 442.5 MiB, with about 1,743,808 records. There are two parts of the program, the one, side a, inserts and updates most of the data. Side b, reads the data and does some minor updates. Currently our biggest day for side a are 800 users (of 40,000 users all year) imputing the system. And our Side b is currently unknown, however we have a total of 1000 clients. The system is most likely going to cap out at 5000 side b clients, with about a year 300,000 side a users. The current database is 5 years old, so we can most likely expect the database to grow pretty rapidly, possibly double each year (which we can most likely archive older records if it comes to that). So with that being said, should we get a server for each side of the app, side a being the master, side b being the slave, any updates made on side b are router to side a. So the question is should i get 2 of these or 1. 2 x Intel Nehalem Xeon E5520 2.26Ghz (8 Cores) 12GB DDRIII Memory 500GB SATAII HDD 100Mbps Port Speed And Naturally I would need to have a redundant backup so it could potentially be 4 of them.

  Read the article

• GA-P55A-UD4 SYSFAN 2 problem....

  - by Vit

  Hi, I have some strange problems with the mobo in title. I have two fans connected to SYSFAN 1 and 2. Both are the same temp regulated Arctic Cooling F12. They are regulated thru temp sensor which is in different cable from fan. It connects to the 3 pin. So, I connected them to SYSFAN 1 and 2 MB ports. The problem is, when PC starts, the fan connected to SYSFAN 1 spins nice and is reporting speed to BIOS. But second fan connected to SYSFAN 2 starts to spin, than stops. I tried to warm the sensor with no help. Also, in BIOS I found no feature about SYSFAN 2 mode or something. I tried the fan itself by connecting it to PWR fan connector and it works fine. But obviously I want it to operate in SYSFAN 2. Please if you have any advice, help. Thanks.

  Read the article

• Touchpad scroll slow and jumpy

  - by IR

  I have a laptop with a synaptics touchpad running on win7 x64. When i use the scrolling region of the touchpad in some applications, for example in Visual Studio 2008, Notepad and Windows Media Player 12, the scroll is very slow. If i pull the edge of the touchpad slowly the program will scroll one row at a time(regardless of the number of lines-settings in the mouse configuration). If i pull the edge quickly though, the program will instantly jump like 20 rows making it way too fast. In some applications, like Firefox, the scrolling work as expected. Changing the scrollspeed-setting for the touchpad does not help. If you make it slower it doesn't do the 20-row jump but then it's horribly slow and if you try to make it faster it will do the jumps all the time. I have tried both synaptics generic drivers and the "special" drivers that HP provides but they both have the same problem (except that the generic one can't adjust the scrolling speed, even though that didn't help anyway). With windows generic drivers the scrolling region doesn't even work. Other mice i've tried with scrollwheel work as they should do.

  Read the article

• How can I change the default program installation directory in Windows 7?

  - by Max

  Windows 7 is installed on my C drive, which is quite small. I am very tired of instructing new programs to put their files on my larger D drive during installation; I would like to change the default drive. This article says that you can use a registry hack, but I am giving Microsoft the benefit of the doubt and naively assuming that a configuration option exists somewhere. It's 2010... do I really have to hack my registry to make a simple tweak like this? Also, there's a ServerFault question that explains how to move the "Users" directory and create a symlink, which could also work. However, at the moment I have some apps in C:\Program Files, some apps in C:\Program Files (x86), and some apps in the corresponding folders on D:\, so it would be a hassle. Also, my small OS boot drive is a 10k RPM WD Raptor, and I feel like that probably gives a speed boost to apps installed on it that need to read & write to their directories a bunch. I wonder if it actually matters.

  Read the article

• 2.6.9 Kernel on virtual server (non upgradable) - any expected problems?

  - by chris_l

  Hi, I'm considering to rent a virtual server (for me personally). The product I'm currently looking at offers IMO fair pricing, very good hardware etc. The only problem is, that I won't be able to do an upgrade to a newer kernel than 2.6.9 (running Debian Etch). Also, I can't install my own kernel modules. (The server runs with Virtuozzo, so as far as I understand it, it just does some chroot instead of a real virtualization (?)) I want to run GlassFish, Postgres, Subversion, Trac and maybe some other things on it. It will also have to employ a firewall, and provide OpenSSL for https. Ideally, it would also be able to do AIO (asynchronous IO), which could speed up some server I/O. Should I expect problems with that old kernel version, in conjunction with the software I want to install (I'd like to use current versions of the software)? One thing I already found out, is that you can't do everything with iptables, since some kernel modules are missing/things are not build into the kernel. GlassFish v3 appears to run fine at first glance. I was able to test the server for a few hours. Installing my whole setup wasn't feasible in that time, but what I can say is, that it's amazingly fast for an entry-level vserver, especially hard disk and network performance (averaging at ca. 400MBit/s). So if the kernel won't be a problem, I'd really like to take it. Thanks, Chris PS Exact kernel version: 2.6.9-023stab051.3-smp

  Read the article

• Exchange 2013 really slow outside of localhost

  - by ItsJustJP

  We've got a 12 core xeon, 24GB of ram 2012 server. We've recently migrated from exchange 2010 (which was on another server) to exchange 2013 which resides on our new 12 core server. Accessing the OWA on the exchange server is fine; it's very quick and responsive however accessing it via any other computer connect to the domain via a 1 gpbs connection and it'll take 10-15 seconds to load. Also running slow is public calenders that people in my place need to access, again taking 10-15 seconds to access and can sometimes cause outlook to not respond. Further to that we have phones that connect via the internet (of course) to the exchange so people can get work emails when they are out of the office. Guess what, this is also running slow. I've have search for many solutions and have tried changing outlook authentication methods but there is no change in speed. The old exchange 2010 server no longer exists but there was no problem before the migration. Has anyone got any suggestions? Thanks :) Must also mention that server 2012 that exchange 2013 is installed on is also the DC. Update: It would appear that any connection via https is slow. It took more than 15 mins for an outlook client to download 50MB of emails (outlook anywhere).

  Read the article

• Faster caching method

  - by pataroulis

  I have a service that provides HTML code which at some point it is not updated anymore. The code is always generated dynamically from a database with 10 million entries so each HTML code page rendering searches there for say 60 or 70 of those entries and then renders the page. So, for those expired pages, I want to use a caching system which will be VERY simple (like just enter a record with the rendered HTML and (if I need) remove it). I tried to do it file-based but the search for the existence of a file and then passing it through php to actually render it , seems like too much for what I want to do. I was thinking of doing it on mysql with a table with MEDIUMBLOBs (each page is around 100k). It would hold about 150000 such records (for now, at least). My question is: Would it be faster to let mysql do the lookup of the file and the passing to php or is the file-based approach faster? The lookup code for the file based version looks like this: $page = @file_get_contents(getCacheFilename($pageId)); if($page!=NULL) { echo $page; } else { renderAndCachePage($pageId); } which does one lookup whether it finds the file or not. The mysql table would just have an ID (the page id) and the blob entry. The disk of the system is a simple SATA raid 1 , the mysql daemon can grab up to 2.5GB of memory (i have a proxy running too, eating the rest of the 16GB of the machine. ) In general the disk is quite busy already. My not using PEAR cache, is because I think (please feel free to correct me on this) it adds overhead I do not need because the page rendering code is called about 2M times per day and I wouldn't want to go through the whole code each time (and yes, I have eaccelerator to cache the code too). Any pointer to what direction I should go, would be greatly welcome. Thanks!

  Read the article

• Windows 7 misses keystrokes from internal keyboard after hibernation (on Acer Aspire 5820)

  - by ron

  I face a very strange symptom on my Acer Aspire laptop (with the factory default Win7 install and divers. Windows update running). After waking the computer from hibernation, it is a pain to type, since on average 5-10 keypresses are missing per 100 presses, using the laptop's keyboard. Steps to reproduce: 1) Power off 2) Power on, wait for system to become usable 3) Open notepad, for 5 times do hit 10x the same character. This gives a similar pattern of 50 chars total: xxxxxxxxxxyyyyyyyyyyaaaaaaaaaassssssssssdddddddddd 4) Optionally repeat. Everything is fine this far. 5) Hibernate. 6) Power on and resume. 7) Repeat steps 3)-4). This time approximately 3-5 character will be missing from each 50 characters. What I ruled out: putting to Sleep or just Locking and resuming from there does not cause problem battery / AC usage does not matter net connection does not matter running processes seem to be the same before and after hibernation key press speed doesn't really matter. For the test I use a nominal 3-5 strokes/second beat. plugging in an external USB keyboard works fine, but the built-in one still misbehaves What could be the problem? How could I diagnose if the keypresses arrive in, but get swallowed at some point? (maybe some nasty keyboard handler hook misbehaves?). Update: It seems that pushing the PowerSmart button and toggling to power saving state fixes the problem. Also, toggling it again back to the original state keeps it fixed. So this may be a fine workaround, but is not a conforming solution.

  Read the article

• Is a modem required to be programmed when using with an internet provider?

  - by Tim

  I wonder if a modem is required to be programmed when using with an internet provider? If yes, what is the purpose of programming a modem? Do both a DSL and a cable ISP both require a modem to be used in an individual home? For example, I have a Motorola modem SURFboard Model:SB5101, Customer S/N: xxx S/N? xxx HFC MAC ID: xxx USB CPE MAC ID: xxx a coil of cable and a splitter from Comcast High-Speed internet Self-Installation Kit, which were bought 5 years ago, when I purchased Comcast internet service from its retailer www.comcastoffers.com. With them, I was hoping to reduce the amount of fee by avoiding to ask Comcast people to come over to install. But I remember at that time Comcast sent its technician here, dismissed my idea of self-installation, saying they needed to use their own modem and charging me a hefty fee, and so my equipments have never been used. I haven't been using Comcast for a long time. I wonder if my modem, cable and splitter (brand new, never used) are still good to use with an internet provider such as Comcast? If needed, we can ignore their policy and just consider the technology side? Or they are not good to use and I must throw them away like trash? Thanks and regards!

  Read the article

• Compiz and Desktop Effects on Netbook with External Monitor

  - by Nerdfest

  I have an Acer Aspire One AO150 and am having trouble plugging in an external monitor under Ubuntu 9.10. There were no problems under 9.04. If I plug in an external monitor once the machine is already up, then bring up the 'display' application to activate it, it basically hangs. There are no problem under these circumstances if I have desktop effects turned off. I've seen a few mentions of this problem on the Ubuntu forums, but never a solid solution. Any ideas? A few more details after a question below. The machine does not respond to its keyboard commands to switch to an external monitor, nor does it respond to Ctrl-Alt-F1, etc to switch out of X. The pointer is visible on the monitors (at the edge of each) and is frozen as a 'busy' cursor, but with no animation. The kernel does respond to SysReq commands (REISUB). In the latest attempt I had the external monitor active earlier, then removed it and activated desktop effects. Upon plugging in the eternal monitor then bringing up the display application, it hangs.

  Read the article

• Windows 7 misses keystrokes from internal keyboard after hibernation (on Acer Aspire 5820)

  - by ron

  I face a very strange symptom on my Acer Aspire laptop (with the factory default Win7 install and divers. Windows update running). After waking the computer from hibernation, it is a pain to type, since on average 5-10 keypresses are missing per 100 presses, using the laptop's keyboard. Steps to reproduce: 1) Power off 2) Power on, wait for system to become usable 3) Open notepad, for 5 times do hit 10x the same character. This gives a similar pattern of 50 chars total: xxxxxxxxxxyyyyyyyyyyaaaaaaaaaassssssssssdddddddddd 4) Optionally repeat. Everything is fine this far. 5) Hibernate. 6) Power on and resume. 7) Repeat steps 3)-4). This time approximately 3-5 character will be missing from each 50 characters. What I ruled out: putting to Sleep or just Locking and resuming from there does not cause problem battery / AC usage does not matter net connection does not matter running processes seem to be the same before and after hibernation key press speed doesn't really matter. For the test I use a nominal 3-5 strokes/second beat. plugging in an external USB keyboard works fine, but the built-in one still misbehaves What could be the problem? How could I diagnose if the keypresses arrive in, but get swallowed at some point? (maybe some nasty keyboard handler hook misbehaves?). Update: It seems that pushing the PowerSmart button and toggling to power saving state fixes the problem. Also, toggling it again back to the original state keeps it fixed. So this may be a fine workaround, but is not a conforming solution.

  Read the article

• Notepad++ FTP best solution

  - by yoda

  Hi, I use Notepad++ for more than 2 years now, and there's only 1 thing that it needs for me to be perfect: a actually-working-ftp-plugin. It has an ftp plugin, written by someone that meanwhile left the project (by meanwhile I mean a long time ago), and since then nobody had courage to improve it. The problem is that it does't handle connections very well. Sometimes it lost connection with the server and literally "blocks", others don't save the files properly, other only load half of the ftp files, etc etc .. My question is: Is there a way to use ftp and notepad++ (without using its build-in ftp or a ftp client like filezilla)? I've tried using NetDrive, but it gets stuck sometimes (makes the editor crash), and everytime the temporary file is refreshed by windows / NetDrive, it will load the new file without asking and skip the pointer to the end of the file (very very very annoying). In case you know how to make the built-in notepad++ ftp plugin work at 100%, I'd be much more happy! I'd like to have some feedback from you guys :) (I'm using Windows Vista) Thanks in advance!

  Read the article

• How many iptables block rules is too many

  - by mhost

  We have a server with a Quad-Core AMD Opteron Processor 2378. It acts as our firewall for several servers. I've been asked to block all IPs from China. In a separate network, we have some small VPS machines (256MB and 512MB). I've been asked to block china on those VPS's as well. I've looked online and found lists which requires 4500 block rules. My question is will putting in all 4500 rules be a problem? I know iptables can handle far more rules than that, what I am concerned about is since these are blocks that I don't want to have access to any port, I need to put these rules before any allow. This means all legitimate traffic needs to be compared to all those rules before getting through. Will the traffic be noticeably slower after implementing this? Will those small VPS's be able to handle processing that many rules for every new packet (I'll put an established allow before the blocks)? My question is not How many rules can iptables support?, its about the effect that these rules will have on load and speed. Thanks.

  Read the article

• Which Cardbus/PCMCIA -> USB card works with external hard drive?

  - by Carl

  I have an HT-Link Cardbus/PCMCIA USB 2.0 2-port card (NEC / 32-bit). My external hard drive w/USB adapter won't work with it, and it will work plugged directly into a USB port on a different laptop. (My USB ports got fried.) I got the card off E-Bay. My MP3 player works plugged into that card. The drivers for the card say "Known limitations: High Speed Isochronus, USB Composite Devices." (No other details provided.) I don't know if the hard drive adapter is "isochronous" or "composite." I've read there are problems with too little power being supplied to the drive. The cable to the drive has two USB plugs on one end, and it doesn't make any difference if I plug both of them into the Cardbus card. What card should I get? I see many different brands on E-Bay. I need one that supplies sufficient power for an external hard drive, and doesn't have any "known limitations" in the way.

  Read the article

• Online FTP or file sharing service [on hold]

  - by Frede

  We need to share large files with clients, e.g. clients upload a large file, we modify it and later make it available for download. Up until now we've used FTP but this has a number of drawbacks. A lot of management of files and setting up accounts etc. We are therefore considering online alternatives. Requirements: Cheap, 8-) Easy to use, ideally just requiring a web browser, but also possible for power users to connect e.g. via FTPS/SFTP No registration requried for users to upload/download files. We ourselves of course need to be able to login an view uploaded files and upload new files. No per user fee High bandwidth. As files may be GBs in size both upload and download speed cannot be too slow Secure. Encryption during upload/download. No way for users to access uploaded files. Once a user has uploaded a file they (or anyone else besides us) should be able to access the file. To download files users get a link with a password. Ideally the link expires after a set time. No software installation We do NOT need any sync features, backup, versioning etc. Just a quick, easy, secure way for us to share files with our clients. Services like JustCloud, DriveHQ etc seems bloated and "too much" for what we need. What other alternatives exist? Thanks!

  Read the article

• Can't connect to wi-fi hotspot in Ubuntu 11.10

  - by ht3t

  I'm new to Ubuntu. I'm having a wireless network problem in Ubuntu 11.10. I made a hotspot using Connectify from a computer which is running Windows 7. I can access it in Windows 7 but not in Ubuntu 11.10. Every time I access it,I get a message "disconnected". I'm using msi fx 400 notebook with Intel Centrino wireless -N 1000 wireless card. Ubuntu version is 11.10 with KDE desktop. $ sudo lshw -c network [sudo] password for ht3t: *-network description: Wireless interface product: Centrino Wireless-N 1000 vendor: Intel Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: wlan0 version: 00 serial: 00:26:c7:56:b8:f0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=iwlagn driverversion=3.0.0-12-generic firmware=39.31.5.1 build 35138 latency=0 link=no multicast=yes wireless=IEEE 802.11bgn resources: irq:44 memory:e7400000-e7401fff *-network description: Ethernet interface product: RTL8111/8168B PCI Express Gigabit Ethernet controller vendor: Realtek Semiconductor Co., Ltd. physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 06 serial: 40:61:86:b6:b1:a2 size: 100Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix vpd bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=r8169 driverversion=2.3LK-NAPI duplex=full firmware=rtl_nic/rtl8168e-2.fw IP=192.168.21.107 latency=0 link=yes multicast=yes port=MII speed=100Mbit/s resources: irq:41 ioport:9000(size=256) memory:e6004000-e6004fff memory:e6000000-e6003fff I can't do anything without internet connection. How can I fix this?

  Read the article

• AT&T Upload Filtering?

  - by xpda

  Using an AT&T DSL, I cannot ftp upload or ftp download a few files of a large 1500 set. The problem is the file name. I can change a few characters of the file name, and they upload fine. I can change the filenames from upper to lower case and they upload fine. If I change back to the original filename, it will not upload again. When it doesn't upload, it starts, transfers about 5% of a 5-10 meg file, and then times out. I have uploaded one of the files under a different name, changed the name back to the original, and it will not download via ftp. It will download onto a browser, and it will ftp download just fine with a different name. It just will not download with ftp. I have reproduced this uploading to three different servers on 1and1 and Amazon EC2. When I try it on a non-AT&T ISP client, it works OK. Here is a file that did not upload until I had renamed it. (I have changed it back to the original name): "http://xpda.com/nautnew/11302 STOVER POINT TO PORT BROWNSVILLE SIDE A.png" This problem is unrelated to connection, speed, and file content. Only things I can see that makes a difference are the file name and ATT DSL. Does ATT have some kind of ftp file filtering? Is there anything else that could cause this behavior?

  Read the article

• Auto-focus xdvi after running viewdvi in Emacs with AUCTeX.

  - by D Connors

  I've been using emacs with AUCTeX mode to edit my latex documents for a few days now, but there's something that's really bugging me. As it should be, whenever I do C-c C-c RET it compiles the file, and if repeat the command it views the output in xdvi. It's also set to the mini-mode TeX-source-specials-mode, so instead of opening a new window in xdvi it only reloads the window that's already open, brings it to the front, and sends me to wherever the pointer was in emacs (forward search). Now here's the problem: Even though the xdvi window is brought to the front, it's not focused. Instead, the emacs windows stays with focus (and that's where any keyboard input goes). And I keep forgetting about that, which leads me to accidentally editing the source file while trying to navigate in xdvi. Not to mention I'm forced to alt-tab in order to focus xdvi, and alt-tab twice if I just want to get back to emacs. Is there a way around this problem? I just want xdvi to be focused whenever I run the view command from emacs.

  Read the article

• Monitor programs accessing my keyboard?

  - by Anti Earth

  As of a few days ago, my computer is behaving 'erratically'. When I am typing, my pointer will randomly move to another place in the text and start typing a semi-random string of characters. ("gvyfn" is common; It has typed this about 8 times whilst I composed all the text above) It often highlights part of or all the text and overwrites it. It sometimes goes into loops of pressing Control-alt-delete down, bringing up Windows 7 menu thing. It sometimes even messes with mouseclicks; they have unexpected results, like requesting admin priveledges from applications, instead of switching to their window. I believe this is because it is holding a alt-function key down. This behaviour happens periodically, in waves. It might subside for an hour, then continue to haunt me. I believe it to be a virus or malicious program. My anti-virus (Symantec) and multiply MS rootkit removers could not find anything suspicious. I've noticed that sometimes it re-maps keys, and types gibberish when I press certain keys (though no pattern is evident). I believe a malicious program has installed a keyhook on my computer. I'm wondering... - Is there a way to let me view which programs are emulating keystrokes? - Is there a way to view what keyboard hooks are installed? (I'm also at liberty to try any other techniques to remove this blasted thing. It is easily the most fustrating computer problem I've encountered). Thanks!

  Read the article

• MacMini transmit rate stuck at 11, every other device can connect at full 54Mbit/s?

  - by chum of chance

  I have a MacMini circa 2007 that's getting very low transmit rates via wifi, 8-11. I have other devices that are getting full 54, including a MacBook Air. With everything else off, the MacMini doesn't want to seem to go any faster. Since it has been previously connected to ethernet its entire life, I was wondering if there were some settings I can change to speed up the connection. Option-clicking the network icon gives this read out: PHY Mode: 802.11g Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -73 Transmit Rate: 11 My new MacBook Air has the following readout: PHY Mode: 802.11n Channel: 1 (2.4 Ghz) Security: WPA2 Personal RSSI: -66 Transmit Rate: 79 Both have full bars and the wireless router is in the same room to eliminate any obstructions from the equation. Could the MacMini be connecting at an older protocol, like 802.11b and be reporting erroneously that it is connected at 802.11g? This would explain why I haven't seen a transmit rate above 11. Any further trouble shooting I can try before buying a new USB 802.11n device? The WiFi router is a DLink DIR-615. I can see other devices, and none, even the other g connected devices, are getting below 30-40 MBit/s. What's going on here?

  Read the article

• Matched or unmatched drives for RAID arrays?

  - by Will

  Looking around there is conflciting information on this, with some strongly suggesting one or the other. From my understanding the issue with matched drives is that the wear on both drives is more or less the same, so the potential for the second drive failing with or very soon after the first is pretty high. People also claim matched drives give substianatally higher performance however assuming the unmatched drives are more or less the same (eg 2, 1 TB STATA II 7200rpm drives with 32MB cache), would the minor differences between say a Seagate and a Western Digital one (say one has a 128MB/s read rate, and the other a 150MB/s read rate, as well as I guess various other minor differences) actually cause any notable performance loss, ie potentialy worse than two matched 128MB/s drives, or does RAID not really care and give you essentially an optimal solution (eg upto 278MB/s total read speed for RAID 0 and 1) and similar for other RAID with more "unmatched" drives (5 and 1+0 come to mind as possibilities)? Also I couldnt find much info on how this is different on different RAID setups, eg RAID 0 or RAID 1, software or hardware RAID, etc. I'm assuming such things have an effect, and thats it's not all the same for RAID in general?

  Read the article

• Some Portions of Computer Running Slow (Specifically Graphics)

  - by Mike Gates

  I noticed that a few things are running slow today on my Windows 7 laptop. Specifically, they are: Opening and closing windows takes several seconds for the animation to complete. Windows media player opens fine, but the movies are very laggy MMORPG's, such as RuneScape, are extremely laggy When waking my computer from sleep mode, after entering my password, my desktop takes about 3 seconds to fade in Other than those, everything runs at a normal speed. Things I've done that maybe contributed to this problem: Changed the graphics processor (by plugging in/unplugging the charger) [however, no matter how I change the graphics, I'm still getting this lagginess] Installed AdBlock, a Firefox addon [I recently removed it, and I'm still experiencing this problem] Went into Advanced System Settings, Clicked Settings, and unchecked a few visual things (such as the animation for opening and closing windows) [sure, this got rid of the opening/closing windows lag, but I like that little animation - plus that leaves all the other lag problems I'm experiencing] So, does anyone have any ideas/fixes? If so, please respond. Thank you. Some Other Information: I'm on a HP Pavillion dv7 laptop, 4285 Entertainment PC, with: intel CORE i5 inside, ATI Mobility Radeon Premium Graphics, Microsoft DirectX11 Opening and closing of windows: Defined as opening a program (i.e. Firefox) or closing it by hitting the X in the upper-right hand corner. Lately, the animation for opening and closing windows (which is simply either growing from the icon from the taskbar to fill the screen, or shrinking from the screen down towards the icon on the toolbar.) This problem also occurs for minimizing/maximizing windows. Very laggy movies: defined as .avi movie files saved to My Documents which skips several frames per second and seemingly slows down the movie as a whole Extremely laggy games: I tried RuneScape today, and movement in the game was at least 10x slower than it ever has been, even when playing on the lowest detail/graphics Desktop taking 3 seconds to fade in after sleep: in this scenario, I had no other programs running visibly. The computer generally fades to black from the password screen to the desktop in about 1 second, normally. However, it is now taking 3 or more seconds.

  Read the article

< Previous Page | 304 305 306 307 308 309 310 311 312 313 314 315  | Next Page >