Search Results

Search found 2439 results on 98 pages for 'alex waters'.

Page 31/98 | < Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >

  • Windows 2003 SP1 terminal server printers Disappear after reboot - HP laserjet 4240

    - by Alex
    had working PCL6 laserjet 4240 driver. needed to downgrade to PCl5, tried but did not get clean install. tried again and it seemed to work (this is 2003 enterprise terminal server SP2) Have over 40 working laserjets (5, 4000, 4100 and 18 of the 4240) After normal nightly reboot the 18 4240 printers were 'gone'. Worked w/Microsoft who said bad HP driver issues - weird since they work on other terminal servers. downloaded latest version, etc. from HP site and can NOT get to work. As soon as I install, then do a Net Stop Spool and Net Start Spooler the printer is 'gone'. Current workaround is to use HP 4000 PCL5 drivers for all of these 4240 printers.

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Nginx: Loopback connection via PHP's getimage size crashes server (Magento's CMS)

    - by Alex
    We were able to trace down a problem that is crashing our NGINX server running Magento until the following point: Background info: Magento Backend has a CMS function with a WYSIWYG editor. This editor loads some pictures via a controller in magento (cms/directive). When we set the NGINX error_log level to info, we get the following lines (line break inserted for better readability): 2012/10/22 18:05:40 [info] 14105#0: *1 client closed prematurely connection, so upstream connection is closed too while sending request to upstream, client: XXXXXXXXX, server: test.local, request: "GET index.php/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL,,/ HTTP/1.1", upstream: "fastcgi://127.0.0.1:9024", host: "test.local" When checking the code in the debugger, the following call does never return (in ´Varien_Image_Adapter_Abstract::getMimeType()` # $this->_fileName is http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif` # $_SERVER['REQUEST_URI'] = http://test.local/admin/cms_wysiwyg/directive/___directive/BASEENCODEDIMAGEURL list($this->_imageSrcWidth, $this->_imageSrcHeight, $this->_fileType, ) = getimagesize($this->_fileName); The filename requests is an URL to the same server which is requesting the script a link to a static .gif that is not existing. Sample URL: http://test.local/skin/adminhtml/base/default/images/demo-image-not-existing.gif When the above line executed, any subsequent request to the NGNIX server does not respond any more. After waiting for around 10 minutes, the NGINX server starts answering requests again. I tried to reproduce the error with a simple test script that only calls getimagesize() with the given URL - but this not crash. It simple leads to an exception saying that the URL could not be loaded (which is fine as the URL is wrong)

    Read the article

  • How can I record system sounds (apps) in Audacity?

    - by Alex
    Or another similar program? All I want to do is record the sounds coming from say firefox, or any other app, for use as samples in music. I need to do this in both windows and linux (ubuntu 9.10). I have looked through the preferences of audacity but didn't find anything that let me select the system sound. Perhaps I overlooked it, because I was able to do this with earlier versions of audacity.

    Read the article

  • is there a way to have VIM do incremental search on text files?

    - by Alex
    Is there a way to have VIM do incremental search on text files? Vim already does incremental search within the currently open file. Examples of programs that demonstrate the type of search I'm trying to accomplish are Notational Velocity for MacOS, Resop for windows or SimpleNote for the web. These apps do an instant or incremental search in the files of a specific directory and make it easy/fast to narrow down the file you are looking for or create a new file. I use both but would rather live in one editor.(that being VIM) Is there some plug in that would do this?

    Read the article

  • Soft links between samba profile and profile.V2

    - by Alex Rose
    I am currently using a samba server to host windows sessions. For the moment, every machine runs windows XP, but in an upcoming hardware upgrade, I will have new Windows 7 machines installed. The problem is that the user directory changed from XP to 7 (for instance 'My Documents' became 'Documents'). To solve that, samba created a folder called profile.V2, which contains files and folders for Windows 7. Now I would like to link the two profiles folders ('profile' from windows XP, 'profile.V2' from windows 7) so that a user can logon from a XP or 7 machine and still have access to the same files. I tried to create softlinks between folder pairs ('Documents' -­­ 'My documents') and it seems to work. My question is : is it likely to create issues in the future?

    Read the article

  • Cannot resolve a single A Record from client machine

    - by Alex
    I set up a simple Bind server on my VPS and it is working properly. The problem occurs with my local windows machines, which are connected to internet through the home router. I created an A-record named 'dev' and it is invisible from my local network for some reason, though people from other locations can resolve dev.mydomain.com. Ironically, dev.mydomain.com cannot be resolved for myself only. If I add another A-record, say, 'gamma' then it becomes visible from my local windows machines instantly. So this is just for that particular 'dev' name. The only difference is that I had dev.mydomain.com server on another IP but that was a month ago; all nameservers have been changed since then. I tried to reboot my router and flushed dns cache on windows machines: no result. Thank you in advance.

    Read the article

  • Tuning MySQL to consume less memory

    - by Alex
    I have a VM which has 2GB Ram, (full specs) And I am setting up a site which has one table in particular with over a million records. There's little or no usage of this particular database (perhaps once or twice a day) but simply running mysql grinds the whole server to a halt. I've looked through the top results but nothing is really denting the CPU however the memory seems to be the issue. The site isnt even live of taking requests yet. the memory situation looks like this: # free -m total used free shared buffers cached Mem: 2006 1880 126 0 3 53 -/+ buffers/cache: 1823 183 Swap: 2047 345 1702 Are there any good pointers to tune mysql to stop hogging the system memory? Thanks very much EDIT: (requested by 8bit): http://tny.cz/b41a0b12

    Read the article

  • Forums that compell one to read? [closed]

    - by Alex
    I want to create a forum for a very specific, somewhat fight-club-like area of information. The participants need to be unique, not people I know. To be precise, it needs to be an entirely random set of participants. To do this I am going on the assumption that whatever a potential viewer sees when he visits this particular domain he will be COMPELLED to go further. He feels an intense urge within him to read more. I need forum software that will evoke this feeling regardless of the content. Minimal and aesthetically fluid and functional. It must have.. zen.. What are my options?

    Read the article

  • Windows 7 RDP Problem - connecting to external zone with computer names

    - by alex
    I recently installed Windows 7, all is well so far, apart from using RDP to access computers outside my domain. We use a datacenter, outside of our domain. I was using Windows Vista before (not sure if this is relevant) - I could RDP no problem to the machines (using their machine names - Web10 for example) I have changed my IP address to be the same as it was when i was using vista We use a draytek firewall - we use DMZ Host to map my IP to an external ip- which is allowed to access the datacenter I've disabled windows firewall When i try to connect in Remote Desktop client, using Web10, I can't connect, however, if I enter the actual IP address, i can. I have run out of ideas... any help is appreciated!

    Read the article

  • How to set local alias for a machine?

    - by Alex G.
    I would like to set an alias on my local PC for a network machine. I know that it can be done by adding an entry in the hosts file as long as the IP address of the machine is also specified. However, the problem is that IPs are dynamically assigned by a DHCP server so I don't know for sure the IP address. Is there a way to define just an alias based on the machine's network name? P.S.: I'm running Windows Server 2008 R2.

    Read the article

  • NAT via iptables and virtual interface

    - by Alex
    I'm trying to implement the following scenario: One VM-host, multiple guest VMs, each one gets its own IP-address (and domain). Our server has only one physical interface, so the intended use is to add virtual interfaces on eth0. To complicate our situation the provider uses port-security on their switches, so I can't run the guest interfaces in bridged mode, because then the switch detects a "spoofed" MAC-address and kills the interface (permanently, forcing me to call the support, which I'm sure will get them a little bit angry the third time ;) ). My first guess was to use iptables and NAT to forward all packages from one virtual interface to another one, but iptables doesn't seem to like virtual interfaces (at least I can't get it to work properly). So my second guess is to use the source IP of the packages to the public interface. Let's assume libvirt creates a virbr0-network with 192.168.100.0/24 and the guest uses 192.168.100.2 as IP-address. This is what I tried to use: iptables -t nat -I PREROUTING --src public_ip_on_eth0:0 -p tcp --dport 80 -j DNAT --to-destination 192.168.100.2:80 That doesn't give me the intended results either (accessing the server times out). Is there a way to do what I'm trying to do, or even to route all traffic to a certain IP on a virtual interface to the VM's device?

    Read the article

  • Lazy linux backup system?

    - by Alex
    Ok, so I want to say Time Machine, but that's note exactly what I'm looking for. I want to set up a system that will regularly (hourly?) back up the /home directory of our machine. time Machine style things are naturally preferable since they save space by only saving the changes, but honestly, this is important enough that I can suffer some waste. Any ideas?

    Read the article

  • Maximise network transfer speed of various applications

    - by Alex
    When using nc, scp, wget to transfer files between 2 machines on a dedicated 2Mbps link, I get speeds between 0.5 and 1 Mbps. However, when I use iperf -c 10.0.1.4 -t 20 -P 12 (for example) I can maximise the speed of the link (getting stable 2Mbps). Is there a way to make single stream transfers (such as those done by scp) to utilise all/most of the link? Some kind of tcp settings, or iptables...?

    Read the article

  • How do you do incremental search across multiple text files in VIM?

    - by Alex
    Is there a way to have VIM do incremental search on text files? Vim already does incremental search within the currently open file. Examples of programs that demonstrate the type of search I'm trying to accomplish are Notational Velocity for MacOS, Resop for windows or SimpleNote for the web. These apps do an instant or incremental search in the files of a specific directory and make it easy/fast to narrow down the file you are looking for or create a new file. I use both but would rather live in one editor.(that being VIM) Is there some plug in that would do this?

    Read the article

  • DNS caching server config problem

    - by Alex
    I have a Bind DNS caching-only server setup that is working. I am bringing up a new AD domain controller that will also be a DNS server for that AD but I don't want it responding to any DNS queries except those that are AD related. So, my goal is to leave this caching server as the primary DNS server for stations on the network and have it forward requests for the AD domain to the domain controller. My understanding is that I just need a forward zone for that domain pointing to the domain controller. However it does not seem to be working. So that leaves me to think that my caching server is not forwarding properly. For example, this AD is going to have a naming convention of hostname.mydomain.local. If I do an nslookup and specify the domain controller's IP address as the server, I can query addresses that exist in DNS on that server, such as dc1.mydomain.local. However, queries to my caching server times out (I get a response from the caching server if I query mydomain.local but none of the objects in that domain). Any suggestions? Here is my named.conf file: options { directory "/var/named"; listen-on { 192.168.0.14; 127.0.0.1; }; forwarders { ; ; }; forward first; }; zone "." in { type hint; file "db.cache"; }; zone "0.0.127.in-addr.arpa" in { type master; file "db.127.0.0"; }; //forward zone for mydomain.local zone "mydomain.local" { type forward; forwarders { 192.168.1.21; }; };

    Read the article

  • SQL Server - VMWare install - Utilize more RAM

    - by alex
    We have a SQL server machine - It’s a VMWare image (running on ESXi hardware etc..) It has windows 2008 x64 standard The SQL install is SQL 2008 standard The virtual machine has 12gb of RAM, and 4 virtual CPU The box is suffering from near 100% CPU a lot of the time I enabled the AWE- but SQL server only seems to use 3-4gb of RAM Is there a way of making it use more available ram more effectively? cache results for example..?

    Read the article

  • How to change the default terminal emulator on Windows (cmd)?

    - by alex
    Is it possible to change the default terminal emulator on Windows (7 and 8 in particular) from cmd to, for example, Console2 or ConEmu? In essence, I want all command line tools, whether launched by double clicking, from "Run" or by other processes to use the custom terminal. This is a trivial matter on Linux, is it even possible on Windows? It would be especially helpful if this could be done via a script.

    Read the article

  • Safe to disable compile options for Nginx (when used only as reverse proxy/cache)

    - by Alex
    I have read that I can do this to make a smaller footprint Nginx when used as static content cache/reverse proxy: --without-mail_pop3_module --without-mail_imap_module --without-mail_smtp_module What other options are safe to disable? SSI, FastCGI? Others? The only requirements for the reverse proxy is to be able to do https and gzip compression. Will disabling all the module really help with footprint and/or performance?

    Read the article

  • FTP Server upload and filesystem questions

    - by Alex
    I'm a photographer who mainly does event photography. A while ago I bought myself a Nikon WT-4 wireless transmitter, a small device which connects via USB to my Nikon D700 DSLR, and then establishes a WiFi connection to an existing WLAN. It can then upload any pictures I take via FTP to an FTP server somewhere in the network. On my laptop I then have a piece of software which will check a given folder on the disk regularly, this software is smart enough to look at the modified file timestamp, if this timestamp is less than 10 seconds ago, it will not attempt to import the folder and skip the file in this iteration of the import scan. The problem I've discovered seems to be inherent to the FTP protocol, as I have the same problem with Windows 7 built in IIS server, as I do with FileZilla FTP server. When the transmitter starts to upload a file, the FTP server will create a small 300-500 KB file with the correct filename on the disk, but then do nothing with the file until it has completely received the file via FTP. So it seems to create this small dummy file, and then buffer the remainder of the FTP upload until it's finished, and then dump the rest of the file into the dummy file making it the correct size. Problem is, these uploads take about 15-30 seconds depending on reception, but since the folder watch tool will already try to import any file older than 10 seconds, it will always try to import the small dummy files which obviously fails as they're not copmlete yet. Is there any way to 'disable' this behaviour? Ideally I would like my file only to show up once it's been completely uploaded. Or perhaps someone knows another FTP server application (it has to run on win7) which does not show this behaviour?

    Read the article

  • Serial Port ttyUSB0

    - by Alex
    I picked up a USB serial null modem cable, so that I can connect up to a headless linux box. As a quick test, I plugged the device into the usb null modem, and the other end I connected to a windows pc. I opened up a terminal on the windows side, with 115200 8N1. On the linux side I opened minicom with the same params. MY problem is that I can type one way from the pc and see the text on the linux minicom side. If I type on the linux side it doesnt show on the pc side. If I reverse the cable it reverses the process. I bet this is a simple issue but I haven't dealt with serial comms in ages. Thanks

    Read the article

< Previous Page | 27 28 29 30 31 32 33 34 35 36 37 38  | Next Page >