Search Results

Search found 19018 results on 761 pages for 'raw input'.

Page 311/761 | < Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >

  • DVI splitter not working as expected/confusion between DVI-D and -I

    - by Freakishly
    Hey guys, thanks for looking. I have an ATI FirePro™ V3700 in my desktop machine, and I have been running a dual-monitor setup quite effortlessly, thanks to the two DVI ports on the card. I came upon a third monitor, and wanted to extend my desktop to 3 screens, so I purchased a DVI splitter from Amazon. Now, I can only duplicate the second monitor onto the third, not extend it. I've tried all possible combinations of input to no avail. Here's the setup: The ATI FirePro™ V3700 has two Dual-Link DVI-I outputs The splitter splits a single Dual-Link DVI-I port into two Dual-Link DVI-I outputs Two of the monitors are NEC E222W, and the third monitor is a Dell 2001FP. Each monitor has one D-Sub and one Dual-Link DVI-D input. Cables going from the video card to the monitors are two Dual-Link DVI-D to the NECs and one Single-Link DVI-D to the Dell. Is the problem likely with the DVI-D/DVI-I mismatch? Or is it with the cable on the Dell that is only a Single-Link? The cables are easily replaceable, the monitors not so much. Thanks for your time, I really appreciate it. http://www.amd.com/us/products/workstation/graphics/ati-firepro-3d/v3700/Pages/v3700-specs.aspx http://www.amazon.com/Cables-Unlimited-DVI-D-Splitter-PCM-2260/product-reviews/B000H09RFM/ref=dp_top_cm_cr_acr_txt?ie=UTF8&showViewpoints=1 www dot newegg dot com/Product/Product.aspx?Item=N82E16824002495 accessories dot us dot dell dot com/sna/PopupProductDetail.aspx?cs=19&l=en&c=us&sku=320-1578 Apologies for the fudged links, I'm new here and they won't let me post more than two :P

    Read the article

  • Sorting IPv4 Addresses

    - by Kumba
    So I've run into a quandary on sorting IPv4 addresses, and didn't know if there was a set rule in some obscure networking document. Do I do a straight sort on the raw address only (such as converting the IP address to a 32bit number and then sorting), do I factor in the CIDR via some mathematical formula, do I sort via the CIDR only (as if I'm comparing the network size and not the addresses directly)? I.e., normal math, we'd do something like -1 < 0 < 1 to denote the order of precedence. Given say, 10.1.0.0/16, 172.16.0.0/12, 192.168.1.0/24, and 192.168.1.42, what would be the order of precedence?

    Read the article

  • OSX Mail.app send only plaintext but read as html

    - by bawkstoo
    I get email which seems properly plaintext formatted, but when I forward it out, the font size ends up being enormous and a few other formatting stupidities. So I tried the following: defaults write com.apple.mail PreferPlainText -bool TRUE And this works great, all outgoing email regardless of the text original is plaintext only, just the way I like it. But now for incoming email only the plaintext portions are available to read without going into View - Message - Raw Source (or something similar to that). Does anyone know how I can force only outgoing mail to include only plaintext, but continue to read incoming mail in the formatting it was intended?

    Read the article

  • Using awk to split text file every 10,000 lines

    - by Sneaky Wombat
    I have a large gzip'd text file. I'd like to something like: zcat BIGFILE.GZ | awk (snag 10,000 lines and redirect to...)|gzip -9 smallerPartFile.gz the awk part up there, I basically want it to take 10,000 lines and send it to gzip and then repeat until all lines in the original input file are consumed. I found a script that claims to do this, but when I run it on my files and then diff the original to the ones that were split and then merged, lines are missing. So, something is wrong with the awk part and I'm not sure what part is broken. Here's the code. Can someone tell me why this doesn't yield a file that can be split and merged and then diff'd to the original successfully? # Generate files part0.dat.gz, part1.dat.gz, etc. # restore with: zcat foo* | gzip -9 > restoredFoo.sql.gz (or something like that) prefix="foo" count=0 suffix=".sql" lines=10000 # Split every 10000 line. zcat /home/foo/foo.sql.gz | while true; do partname=${prefix}${count}${suffix} # Use awk to read the required number of lines from the input stream. awk -v lines=${lines} 'NR <= lines {print} NR == lines {exit}' >${partname} if [[ -s ${partname} ]]; then # Compress this part file. gzip -9 ${partname} (( ++count )) else # Last file generated is empty, delete it. rm -f ${partname} break fi done

    Read the article

  • How do you passthrough native SATA drives to a guest on ESXi?

    - by John
    I have ESXi 4.0 running on an Intel DX58S0 Mothboardboard with an Intel Core i7 930 processor. VT-d is also enabled. I have three drives in the system, drive 0 is used for ESXi. Drive 1 and 2 contain data from an older machine and show up under the "Storage Adapters" section in configuration. I would like to allow a guest machine to access the data on these drives (as nativly as possible). I have enabled passthrough of the motherboard's built in SATA controller (Intel/Marvell 88SE6121 ). This controller shows up in my guest OS, but the guest shows no drives aside from the normal virtual drive. I have tried a Linux guest and Windows7. I have also configured the host machine to try IDE/RAID/ACHI modes for the SATA controller. Any ideas how I can configure one of my guests to get at the raw data on these drives?

    Read the article

  • How to set a static route for an external IP address

    - by HorusKol
    Further to my earlier question about bridging different subnets - I now need to route requests for one particular IP address differently to all other traffic. I have the following routing in my iptables on our router: # Allow established connections, and those !not! coming from the public interface # eth0 = public interface # eth1 = private interface #1 (10.1.1.0/24) # eth2 = private interface #2 (129.2.2.0/25) iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i eth0 -j ACCEPT iptables -A FORWARD -i eth0 -o eth1 -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth0 -o eth2 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the private interfaces iptables -A FORWARD -i eth1 -o eth0 -j ACCEPT iptables -A FORWARD -i eth2 -o eth0 -j ACCEPT # Allow the two private connections to talk to each other iptables -A FORWARD -i eth1 -o eth2 -j ACCEPT iptables -A FORWARD -i eth2 -o eth1 -j ACCEPT # Masquerade (NAT) iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE # Don't forward any other traffic from the public to the private iptables -A FORWARD -i eth0 -o eth1 -j REJECT iptables -A FORWARD -i eth0 -o eth2 -j REJECT This configuration means that users will be forwarded through a modem/router with a public address - this is all well and good for most purposes, and in the main it doesn't matter that all computers are hidden behind the one public IP. However, some users need to be able to access a proxy at 192.111.222.111:8080 - and the proxy needs to identify this traffic as coming through a gateway at 129.2.2.126 - it won't respond otherwise. I tried adding a static route on our local gateway with: route add -host 192.111.222.111 gw 129.2.2.126 dev eth2 I can successfully ping 192.111.222.111 from the router. When I trace the route, it lists the 129.2.2.126 gateway, but I just get * on each of the following hops (I think this makes sense since this is just a web-proxy and requires authentication). When I try to ping this address from a host on the 129.2.2.0/25 network it fails. Should I do this in the iptables chain instead? How would I configure this routing?

    Read the article

  • Hyper-V and host-installed hardware devices: can guest VMs access?

    - by gravyface
    Have a couple of servers I'd like to setup as Hyper-V Servers, with a couple of Windows 2008 Standard VMs. On the host, we have a few hardware devices we'd like to be accessible to the guest; I'm not sure if these are supported via a raw "pass-thru" on Hyper-V (which I don't have alot of experience with) if the same drivers are installed on the guest. Hardware in question is a Brooktrout fax card, a SCSI adapter for the tape drive, and a 9-pin serial connected to one of the core firewalls for management.

    Read the article

  • Using keyboard disables touchpad left button for a second on Acer laptop in Windows 8.1

    - by Robert Kilar
    The problem is present in the whole system not only in games: desktop, chrome, games, everywhere. When I press any "input key" on a keyboard for example in desktop I can't select the file by left mouse button OR by tapping the touchpad for about one second(right button works immediately). Later on the LMB works well. There is NO delay, button is just deactivated for a second. In games that means that when I run I cannot shoot for example. When I switched LMB and RMB functions in windows control panel still the LMB is getting disabled and RMB works fine. By "input key" I mean letter or a number, keys like Alt, CapsLock, Ctrl does not affect touchpad. I do not remember that problem when I used Windows 7. USB mouse works like it should. The problem existed when I was using Elantech touchpad driver and after I uninstalled it and used Windows 8.1 generic driver. EDIT I installed the Elantech drivers and set values to 0 at every disable... key. But the problem is still present. EDIT 2 THE LAPTOP IS Acer V3-571G I have turned off disabling function in touchpad but it did not fix it. I know that touchpad is NOT broken down. Turned on the animated touchpad icon of elantech drivers and put it on the task bar(on a picture) When I type the letter and press the LMB the dynamic icon displays the click but it is ignored.

    Read the article

  • Bandwidth monitoring with iptables for non-router machine

    - by user1591276
    I came across this tutorial here that describes how to monitor bandwidth using iptables. I wanted to adapt it for a non-router machine, so I want to know how much data is going in/coming out and not passing through. Here are the rules I added: iptables -N ETH0_IN iptables -N ETH0_OUT iptables -I INPUT -i eth0 -j ETH0_IN iptables -I OUTPUT -o eth0 -j ETH0_OUT And here is a sample of the output: user@host:/tmp$ sudo iptables -x -vL -n Chain INPUT (policy ACCEPT 1549 packets, 225723 bytes) pkts bytes target prot opt in out source destination 199 54168 ETH0_IN all -- eth0 * 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 1417 packets, 178128 bytes) pkts bytes target prot opt in out source destination 201 19597 ETH0_OUT all -- * eth0 0.0.0.0/0 0.0.0.0/0 Chain ETH0_IN (1 references) pkts bytes target prot opt in out source destination Chain ETH0_OUT (1 references) pkts bytes target prot opt in out source destination As seen above, there are no packet and byte values for ETH0_IN and ETH0_OUT, which is not the same result in the tutorial I referenced. Is there a mistake that I made somewhere? Thanks for your time.

    Read the article

  • How to connect computers to a network printer behind a router?

    - by kokbira
    General question: How to connect computers to an IP printer behind a router? Particular question: How to connect C-1 and C-2 to PRI? What? Where? [ISP] | | -> IPs:200.X.X.X/other configs:DC | [R-1] | | -> IPs:10.1.X.X locked by MAC,M:255.0.0.0,G:10.1.0.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [PRI] IP:10.1.7.7 [R-2] IP: 10.1.0.1,MAC:A | | -> IPs:192.168.1.X,M:255.255.255.0,G:192.168.1.1 |¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯¯| | | [C-1] IP:192.168.1.2 [C-2] IP:192.168.1.3,MAC:A Glossary and details: ------------------------------------------------------------------------------------ - IP: IP. - IPs: Some IP range. - M: Mask. - G: Gateway. - MAC:A: A MAC address that I will not inform you :) - DC: Don't care. - ISP: Internet Service Provider (not so much details about it on that case). - R-1: A real router or some concatenated so IP range bellow that block is 10.1.X.X and above is ISP. The provided IPs are provided by MAC. As all available addresses are in use, you must clone an existing one to join with a new device (and to disconnect the cloned one). - PRI: An network printer (some people here call that IP printer). - R-2: A TP-LINK TL-WR340G, mine wireless router (since my computer does not have ethernet input, it is my ethernet-wifi adapter :), admin access, MAC address cloned from C-2 (MAC:A). I've to configure 10.0.1.1 and 10.0.1.2 as DNS addresses, other wise I cannot connect C-1 and C-2 to Internet. - C-1: My computer, a CCE XLE-425 (remember: no ethernet input), with Windows 7, admin access. - C-2: another computer with better configs than mine, MAC:A, Windows XP. Requirements: I want to print, to access Internet and to do it myself (no need to call network admin men in black people). Pay attention to MAC clones and DNS info.

    Read the article

  • Consume an XML Feed with PowerPoint 2010

    - by Matt Schweers
    Hi there. I'm looking for a way to consume an XML feed from a web-service directly into PowerPoint 2010. I found the LiveWeb plugin (http://skp.mvps.org/liveweb.htm) for PowerPoint that, while pretty cool, really only pulls in actual web content in a way that feels more like an iframe. Ideally, I would like to consume raw XML web service/feed with PowerPoint, parse it, and stylize the results. Is this possible? Even reading from a static XML file would be a good start.

    Read the article

  • Wireless Access Point stopped working

    - by Alex Pritchard
    I have a simple LAN set up at home using a Linksys WRT54GSV4 as my primary router and an Encore ENHWI-2AN3 as an access point. I connect the Encore to the Linksys by running a cable from one of the Linksys LAN ports into the Encore WAN input. I originally configured this using the Encore setup wizard, setting the device up in AP Router Mode. It detected the input network and worked about as expected, creating a second network that used my primary network to connect to the internet. It worked fine for about 2 weeks, then abruptly cut out today. I checked to make sure the network was still live through the cable going into the Encore (provides internet when connected to a laptop directly) and that devices are still able to connect to the network being broadcast by the Encore. When I try to rerun the connection wizard on the Encore, I receive the message "No Services found in WAN port." The WAN Settings is no longer retrieving a dynamic ip from the line. I tried providing a static IP, assigning an IP address within the subnet range of my primary router that wasn't being used and pointing the Default Gateway to the Linksys IP, but this did not work either. When I plug the cable into the WAN port, an internet light comes on that is not lit when a live network is not connected. I've tried doing a hard reset on the Encore (held down the rest button until the lights flashed, reconfigured from scratch), but the WAN settings are still not detected. Also tried powering off and on the modem, linksys, and encore. Any suggestions would be appreciated!

    Read the article

  • Hyper-V and host-installed hardware devices: can guest VMs access?

    - by gravyface
    Have a couple of servers I'd like to setup as Hyper-V Servers, with a couple of Windows 2008 Standard VMs. On the host, we have a few hardware devices we'd like to be accessible to the guest; I'm not sure if these are supported via a raw "pass-thru" on Hyper-V (which I don't have a lot of experience with) if the same drivers are installed on the guest. Hardware in question is a Brooktrout fax card, a SCSI adapter for the tape drive, and a 9-pin serial connected to one of the core firewalls for management.

    Read the article

  • Set Final Cut Express Sequence Options 4:3 to 960p (30fps)

    - by Maccaius
    Hi I have an project in FCE which was recorded in MPEG-4 video in 1280 x 960 (1,4MB/s) and whenever I import those mov files to FCE thez show just fine. but when i add the clips to the timeline (sequence) the quality is cropped - instead of HD i can onlz export the timeline with quicktime conversion and a resolution of 720 x 480. can anybody help me out and tell me how i can export the timeline in full HD quality (as the raw material itself is)? tried the quick setup and exporting as divx and AIC which doesnt reallz work. the actual video size is HD, but qualitz of the video is like SD...

    Read the article

  • What's a good tool for checking from my own machine that my server is up?

    - by chico
    I'm looking for a good tool (web site or not) that I can use to do a simple check whether my web server is accessible from outside LAN (it's serving in a non-standard port). To give some context, I've gone through this problem: can't access my ip from outside. Even the tools I've found are not really working. Currently to fetch the html I serve with the online bash tool I do: curl <my ip>:<my port> \ | sed 's/&/\&amp;/g; s/</\&lt;/g; s/>/\&gt;/g; s/"/\&quot;/g; s/'"'"'/\&#39;/g' I'm looking for a simple tool that can display the html properly, or just show raw text without resorting to sed html escaping and curl.

    Read the article

  • Lots of artifacts while streaming HD content with VLC 0.9.9 on CentOS

    - by Zsub
    I'm trying to stream (multicast) a x264 encoded file using VLC. This in itself succeeds, but the stream has a huge lot of artifacts. This seems to suggest that the data cannot be transported fast enough. If I check network usage, though, it's only using about 15 mbit. I have a similar SD stream which functions perfectly. I think I could improve stream performance by not streaming the raw data, but I cannot seem to get this working. It seems that on keyframes all artifacts are removed for a short while (less than a second). This is the command I use: vlc -vv hdtest.mkv --sout '#duplicate{dst=rtp{dst=ff02::1%eth1,mux=ts,port=5678,sap,group="Testgroup",name="TeststreamHD"}}' --loop Which is all one long line.

    Read the article

  • How can I combine 30,000 images into a timelapse movie?

    - by Swift
    I have taken 30,000 still images that I want to combine into a timelapse movie. I have tried QuickTime Pro, TimeLapse 3, and Windows Movie Maker, but with such a huge amount of images, each of the programs fail (I tried SUPER ©, but couldn't get it to work either...?). It seems that all of these programs crash after a few thousand pictures. The images I have are all in .JPG format, at a resolution of 1280x800, and I'm looking for a program that can put these images into a timelapse movie in some kind of lossless format (raw/uncompressed AVI would be fine) for further editing. Does anyone have any ideas, or has anyone tried anything like this with a similar number of pictures?

    Read the article

  • Install multiport module on iptables

    - by tarteauxfraises
    I'am trying to install "fail2ban" on Cubidebian, a Debian port for Cubieboard (A raspberry like board). The following rule failed due to "-m multiport --dports ssh" options (It works, when i run manually the command without multiple options). $ iptables -I INPUT -p tcp -m multiport --dports ssh -j fail2ban-ssh" iptables: No chain/target/match by that name. When i make a cat on "/proc/net/ip_tables_matches", i see that multiport module is not loaded: $ cat /proc/net/ip_tables_matches u32 time string statistic state owner pkttype mac limit helper connmark mark ah icmp socket socket quota2 policy length iprange ttl hashlimit ecn udplite udp tcp The result of iptables -L -n -v command : $ iptables -L -n -v Chain INPUT (policy ACCEPT 6 packets, 456 bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 3 packets, 396 bytes) pkts bytes target prot opt in out source destination Chain fail2ban-apache (0 references) pkts bytes target prot opt in out source destination 0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0 Chain fail2ban-ssh (0 references) pkts bytes target prot opt in out source destination 0 0 RETURN all -- * * 0.0.0.0/0 0.0.0.0/0 What can i do to compile or to enable the multiport module? Thanks in advance for your help

    Read the article

  • How can I can delete a project in Aperture, but not in Flickr?

    - by jchatard
    I have a Macbook Air as my only computer ; I store my shots on Flickr. The size of the SSD doesn't allow me to keep all my RAW files on my laptop. So I publish the photographs I like in their final state on Flickr with the built-in feature of Aperture. When I hit delete on a project (in Aperture) the message clearly indicates that all photos synched to any service like Facebook, Flickr or any other will be deleted. How can I can around this without the hacky way of unlinking Aperture from Flickr before deleting the project?

    Read the article

  • iptables logging not working?

    - by vps_newcomer
    OS: Ubuntu 10.04 Logging daemon: rsyslog For some reason i'm not getting any iptables logs, even thought i don't look through them very often i'd still like to get it working for the sake of it working XD Here is my /etc/ryslog.d/iptables.conf :msg, contains, "[IPTABLES]" -/var/log/iptables.log & ~ My iptables logging prefix is "[IPTABLES]" followed by whatever else (example [IPTABLES] Denied xyz) the /var/log/iptables.log file is being created, however its not getting any entries. I can see the logging entries in dmesg but not in syslog or messages. Whats going on? EDIT: My iptables logging rules: # logging limit LoggingLimit=5/min LoggingPrefix=IPTABLES # Logging chain iptables -N LOG_REJECT iptables -A LOG_REJECT -j LOG # join INPUT to LOG_REJECT iptables -A INPUT -j LOG_REJECT # logging iptables -A LOG_REJECT -p tcp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied TCP: " #--log-level 7 iptables -A LOG_REJECT -p udp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied UDP: " #--log-level 7 iptables -A LOG_REJECT -p icmp -m limit --limit $LoggingLimit -j LOG --log-prefix "$LoggingPrefix Denied ICMP: " #--log-level 7 Update: I found a thread that has the same symptoms as i do, apparently is a kernel bug. I am using a VPS so could anyone point me on how to upgrade my kernel or apply a workaround? I couldn't find a 2.6.34 kernel listed in apt-cache. Thread: http://www.linode.com/forums/viewtopic.php?t=5533

    Read the article

  • How can I combine 30,000 images into a timelapse movie?

    - by Swift
    I have taken 30,000 still images that I want to combine into a timelapse movie. I have tried QuickTime Pro, TimeLapse 3, and Windows Movie Maker, but with such a huge amount of images, each of the programs fail (I tried SUPER ©, but couldn't get it to work either...?). It seems that all of these programs crash after a few thousand pictures. The images I have are all in .JPG format, at a resolution of 1280x800, and I'm looking for a program that can put these images into a timelapse movie in some kind of lossless format (raw/uncompressed AVI would be fine) for further editing. Does anyone have any ideas, or has anyone tried anything like this with a similar number of pictures?

    Read the article

  • sql server uninstallation issue

    - by angel
    I'm unable to remove SQL Server 2008 sp1 completely from my system. I'm using windows 7 ultimate. Everytime I try uninstalling it i get the following error. How can I remove it? here is the log: Overall summary: Final result: Failed: see details below Exit code (Decimal): -2068643839 Exit facility code: 1203 Exit error code: 1 Exit message: Failed: see details below Start time: 2013-06-24 21:10:38 End time: 2013-06-24 21:21:17 Requested action: Uninstall Log with failure: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\sql_rs_Cpu64_1.log Exception help link: http://go.microsoft.com/fwlink?LinkId=20476&ProdName=Microsoft+SQL+Server&EvtSrc=setup.rll&EvtID=50000&ProdVer=10.0.1600.22 Machine Properties: Machine name: ABHI-PC Machine processor count: 4 OS version: Windows Vista OS service pack: Service Pack 1 OS region: United States OS language: English (United States) OS architecture: x64 Process architecture: 64 Bit OS clustered: No Product features discovered: Product Instance Instance ID Feature Language Edition Version Clustered Sql Server 2008 MSSQLSERVER MSRS10.MSSQLSERVER Reporting Services 1033 Enterprise Edition 10.0.1600.22 No Sql Server 2008 Management Tools - Basic 10.0.1600.22 No Package properties: Description: SQL Server Database Services 2008 SQLProductFamilyCode: {628F8F38-600E-493D-9946-F4178F20A8A9} ProductName: SQL2008 Type: RTM Version: 10 SPLevel: 0 Installation edition: ENTERPRISE User Input Settings: ACTION: Uninstall CONFIGURATIONFILE: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini FEATURES: RS,SSMS,SNAC_SDK,CE_RUNTIME,CE_TOOLS,SNAC HELP: False INDICATEPROGRESS: False INSTANCEID: INSTANCENAME: MSSQLSERVER MEDIASOURCE: QUIET: False QUIETSIMPLE: False X86: False Configuration file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\ConfigurationFile.ini Detailed results: Feature: SQL Client Connectivity Status: Skipped MSI status: Passed Configuration status: Passed Feature: SQL Client Connectivity SDK Status: Skipped MSI status: Passed Configuration status: Passed Feature: Reporting Services Status: Failed: see logs for details MSI status: Passed Configuration status: Failed: see details below Configuration error code: 0xFFD65603 Configuration error description: Input string was not in a correct format. Configuration log: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\Detail.txt Feature: SQL Compact Edition Tools Status: Passed MSI status: Passed Configuration status: Passed Feature: SQL Compact Edition Runtime Status: Skipped MSI status: Passed Configuration status: Passed Feature: Management Tools - Basic Status: Failed: see logs for details MSI status: Passed Configuration status: Passed Rules with failures: Global rules: There are no scenario-specific rules. Rules report file: C:\Program Files\Microsoft SQL Server\100\Setup Bootstrap\Log\20130624_210908\SystemConfigurationCheck_Report.htm

    Read the article

  • How can I check cells for number series?

    - by Stephen Younger
    I have a bit of a problem evaluating an excel cell. Example: M M M M M M M M M 1 2 3 4 5 6 7 8 9 2;5;7 1;9 3;5;7;9 I have a number of excel cells which contain numbers (months). In the first column I have a series of numbers. I want to use conditional formatting to color the corresponding cells in the right columns. If correctly colored I would get something like this: M M M M M M M M M 1 2 3 4 5 6 7 8 9 2;5;7 X X X 1;9 X X 3;5;7;9 X X X X The formula I have now is this: IF(ISNUMBER(FIND(L$22;$K23));$H23;"") but the problem is that cells are colored too which contain part of a number. If I enter 10;15 as input I get this: M M M M M M M M M M M M M M M 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 10;15 X X X X because 1 and 5 are found too. I only want column 10 and 15 to be marked. How can I change the formula or the input?

    Read the article

  • Windows Server 2008 R2 creating a multi-year client certificate using the IIS certsrv page while deploying SSTP VPN

    - by Warren P
    I am trying to follow instructions on Technet about deploying a Standard (non-enterprise) SSTP based VPN) that were originally written for Server 2008, but I am using Server 2008 R2, I have gotten as far as the part where it asks you to create a request a Server Authentication certificate. I have deployed IIS, and Active Directory Certificate Services, and chose "Standalone" and "Standard" (non-enterprise) Certificate Authority because I don't have an OID and don't think I should have to get one for a simple deployment of SSTP. The resulting certificates made by the Certification Authority "Issue" command, only have a 1 year period of validity, I want a multi-year certificate. At no point in this process is there any way to input this information unless it's through the Attributes text input area on the Advance Certificate Request page, which appears to be generated using an old ActiveX control, which means I can only do this using the workarounds in the article that I linked at the top, and only using Internet Explorer. Update:: It may be that this question is pointless since self-signed keys do not appear to work, when I try them, using Windows 8 as the VPN client. The problem is that the keys that are self-created by the technique shown here do not have any Certificate Revocation Server URLs and so you get an error "The revocation function was unable to check revocation", and the VPN connection fails.

    Read the article

  • How to recover the data from the crashed (external) hard disk drive (NTFS)?

    - by shveerab
    The 300 GB harddisk has 2 partitions,90 GB and 200 GB! I can see the drives in windows(XP) but unable to access them, the file system is shown as RAW, 0 used space and 0 free space!..chkdsk returns the error "unable to determine volume version and date. chkddsk aborted." Is the MBR corrupt? How do I restore it? TestDisk tool isn't recognizing the partitions and says invalid entry for heads/cylinder, 15 and should be 255 and suggests to change it..Should I go ahead and change it? Please advise!

    Read the article

< Previous Page | 307 308 309 310 311 312 313 314 315 316 317 318  | Next Page >