Search Results

Search found 111524 results on 4461 pages for 'user mode linux'.

Page 313/4461 | < Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >

  • Postfix server to receive emails for anyonymous user

    - by sachitad
    I have a postfix server configured with imap. Only the recipient with the user account in the system is accepted. For example: rcpt to: test@localhost will yield the following error: 550 5.1.1 <test@localhost>: Recipient address rejected: User unknown in local recipient table What I want to achieve is setup virtual maps which accepts email to all the users (even if the user doesn't accept in the system) then forward all those emails to a specific user mailbox. Is something like this, possible?

    Read the article

  • Can Gitosis enforce correct user name/email?

    - by koumes21
    Gitosis is able to authenticate users based on public/private key pair. It is able to find out which user is currently committing. However, the user name and email is taken from the client's Git configuration ('git config user.name' etc.), which can be set to arbitrary values. Is there any way to associate user names and emails with their public keys and then make Gitosis uses these names and emails as the name and email of the committer?

    Read the article

  • How to create a local user with the same name as a likewise domain user?

    - by JamesRyan
    I need to create a local user with the same name as a domain user under CentOS with Likewise installed. When I use Useradd it says user exists, because a domain user with the same name exists. It is a service account for backup and does not work using a domain account. On machines where the local account was added before likewise was installed it works fine. Is there a way to temporarily disable this check?

    Read the article

  • ec2-user password for running sudo -H -u

    - by bool.dev
    I have to run this command to initialize gitosis: sudo -H -u git gitosis-init < /home/ec2-user/id_rsa.pub But that asks me for a password for ec2-user: $ sudo -H -u git gitosis-init < id_rsa.pub [sudo] password for ec2-user: I do not have a password as i use the default .pem key file to login. I know i can probably login as the git user and do this, but is there any other way? Update: Using Linux AMI 12.09 (micro-instance), in region us-east-1 (N. Virginia)

    Read the article

  • Can't recover hard drive

    - by BreezyChick89
    My drive got corrupt after a thunderstorm. It used to be 1 partition of 2.5tb but now it shows 2 partitions. It's weird because 300gig free space is about how much it had before corrupting, but it was part of the first partition. I tried $ sudo resize2fs -f /dev/sdb1 Resizing the filesystem on /dev/sdb1 to 536870911 (4k) blocks. resize2fs: Can't read an block bitmap while trying to resize /dev/sdb1 Please run 'e2fsck -fy /dev/sdb1' to fix the filesystem after the aborted resize operation. sudo e2fsck -f /dev/sdb1 e2fsck 1.42 (29-Nov-2011) The filesystem size (according to the superblock) is 610471680 blocks The physical size of the device is 536870911 blocks Either the superblock or the partition table is likely to be corrupt! Abort? n .... Error reading block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes Force rewrite<y>? yes Error writing block 537395215 (Invalid argument) while reading inode and block bitmaps. Ignore error<y>? yes ... A lot of these. I can't use e2fsck -y because the first question aborts if I say "y". If I put a weight on the 'y' key it fails because none of the errors were really fixed. I asked this question before and tried using gparted but gparted fails because the first thing it does is: e2fsck -f -y -v /dev/sdb1 giving the same error. The disk status says healthy. There are no bad blocks. This is very frustrating because I can see the data in testdisk and it looks like it's all there. I already bought another 2.5tb drive and made a clone using dd. The next step if I can't fix this is to wipe that drive and just move the data with testdisk, but it seems certain folders will copy infinitely until the drive is full because of symlinks or errors so it's also a difficult option. sudo fdisk -l Disk /dev/sdb: 2500.5 GB, 2500495958016 bytes 255 heads, 63 sectors/track, 304001 cylinders, total 4883781168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0x0005da5e Device Boot Start End Blocks Id System /dev/sdb1 * 2048 4294969342 2147483647+ 83 Linux sudo badblocks -b 4096 -n -o badfile /dev/sdb 610471680 536870911 badfile is empty I also tried changing the superblock with "fsck -b" but all of them are the same.

    Read the article

  • how can I parse and group/do stats on user agent strings?

    - by user151841
    I have a database that has the various user-agent strings of visitors to our site. I'd like to do a 'survey' of them to see what browsers our users are using, so that I can know what features I can use in future development. Is there a tool to parse and run statistics on user-agent strings, or a bunch of strings like this? Ideally, I'd like to see a hierarchical grouping of the stats. For instance: Opera/9.80 (Windows Mobile; WCE; Opera Mobi/WMD-50301; U; en) Presto/2.4.13 Version/10.00 Opera/9.80 (J2ME/MIDP; Opera Mini/4.2.14912/1280; U; en) Presto/2.2.0 Opera/9.80 (J2ME/MIDP; Opera Mini/4.2.13918/812; U; en) Presto/2.2.0 Opera/9.64 (Macintosh; Intel Mac OS X; U; en) Presto/2.1.1 Opera/9.60 (J2ME/MIDP; Opera Mini/4.2.13918/786; U; en) Presto/2.2.0 Opera/9.60 (J2ME/MIDP; Opera Mini/4.0.10992/432; U; en) Presto/2.2.0 I'd like to see 6 entries for Opera, broken down into 3 for 9.80, 1 for 9.64 and 2 for 9.60, and so forth for all browsers. Other dimensions, such as OS, would cross the boundaries of the browser version hierarchy, but it might be nice to see also.

    Read the article

  • Is it possible to have WAMP run httpd.exe as user [myself] instead of local SYSTEM?

    - by Olivier H
    Hello! I run a django application over apache with mod_wsgi, using WAMP. A certain URL allows me to stream the content of image files, the paths of which are stored in database. The files can be located whether on local machine or under network drive (\my\network\folder). With the development server (manage.py runserver), I have no trouble at all reading and streaming the files. With WAMP, and with network drive files, I get a IOError : obviously because the httpd instance does not have read permission on said drive. In the task manager, I see that httpd.exe is run by SYSTEM. I would like to tell WAMP to run the server as [myself] as I have read and write permissions on the shared folder. (eventually, the production server should be run by a 'www-admin' user having the permissions) Mapping the network shared folder on a drive letter (Z: for instance) does not solve this at all. The User/Group directives in httpd.conf do not seem to have any kind of influence on Apache's behaviour. I've also regedited : I tried to duplicate the HKLM[...]\wampapache registry key under HK_CURRENT_USER\ and rename the original key, but then the new key does not seem to be found when I cmd this > httpd.exe -n wampapache -k start or when I run WAMP. I've run out of ideas :) Has anybody ever had the same issue?

    Read the article

  • nginx problem accessing virtual hosts

    - by Sc0rian
    I am setting up nginx as a reverse proxy. The server runs on directadmin and lamp stack. I have nginx running on port 81. I can access all my sites (including virtual ips) on the port 81. However when I forward the traffic from port 80 to 81, the virtual ips have a message saying "Apache is running normally". Server IPs are fine, and I can still access virtual IP's on 81. [root@~]# netstat -an | grep LISTEN | egrep ":80|:81" tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <virtual ip>:81 0.0.0.0:* LISTEN tcp 0 0 <serverip>:81 0.0.0.0:* LISTEN tcp 0 0 :::80 :::* LISTEN apache 24090 0.6 1.3 29252 13612 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24092 0.9 2.1 39584 22056 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24096 0.2 1.9 35892 20256 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24120 0.3 1.7 35752 17840 ? S 18:34 0:00 /usr/sbin/httpd -k start -DSSL apache 24495 0.0 1.4 30892 14756 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24496 1.0 2.1 39892 22164 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24516 1.5 3.6 55496 38040 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24519 0.1 1.2 28996 13224 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24521 2.7 4.0 58244 41984 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24522 0.0 1.2 29124 12672 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24524 0.0 1.1 28740 12364 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24535 1.1 1.7 36008 17876 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24536 0.0 1.1 28592 12084 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24537 0.0 1.1 28592 12112 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24539 0.0 0.0 0 0 ? Z 18:35 0:00 [httpd] <defunct> apache 24540 0.0 1.1 28592 11540 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL apache 24541 0.0 1.1 28592 11548 ? S 18:35 0:00 /usr/sbin/httpd -k start -DSSL root 24548 0.0 0.0 4132 752 pts/0 R+ 18:35 0:00 egrep apache|nginx root 28238 0.0 0.0 19576 284 ? Ss May29 0:00 nginx: master process /usr/local/nginx/sbin/nginx -c /usr/local/nginx/conf/nginx.conf apache 28239 0.0 0.0 19888 804 ? S May29 0:00 nginx: worker process apache 28240 0.0 0.0 19888 548 ? S May29 0:00 nginx: worker process apache 28241 0.0 0.0 19736 484 ? S May29 0:00 nginx: cache manager process here is my nginx conf: cat /usr/local/nginx/conf/nginx.conf user apache apache; worker_processes 2; # Set it according to what your CPU have. 4 Cores = 4 worker_rlimit_nofile 8192; pid /var/run/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] ' '"$request" $status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; server_tokens off; access_log /var/log/nginx_access.log main; error_log /var/log/nginx_error.log debug; server_names_hash_bucket_size 64; sendfile on; tcp_nopush on; tcp_nodelay off; keepalive_timeout 30; gzip on; gzip_comp_level 9; gzip_proxied any; proxy_buffering on; proxy_cache_path /usr/local/nginx/proxy_temp levels=1:2 keys_zone=one:15m inactive=7d max_size=1000m; proxy_buffer_size 16k; proxy_buffers 100 8k; proxy_connect_timeout 60; proxy_send_timeout 60; proxy_read_timeout 60; server { listen <server ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <server host name> _; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<server ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } location /nginx_status { stub_status on; access_log off; allow 127.0.0.1; deny all; } } include /usr/local/nginx/vhosts/*.conf; } here is my vhost conf: # cat /usr/local/nginx/vhosts/1.conf server { listen <virt ip>:81 default rcvbuf=8192 sndbuf=16384 backlog=32000; # Real IP here server_name <virt domain name>.com ; # "_" is for handle all hosts that are not described by server_name charset off; access_log /var/log/nginx_host_general.access.log main; location / { proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_pass http://<virt ip>; # Real IP here client_max_body_size 16m; client_body_buffer_size 128k; proxy_buffering on; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 120; proxy_buffer_size 16k; proxy_buffers 32 32k; proxy_busy_buffers_size 64k; proxy_temp_file_write_size 64k; } }

    Read the article

  • Enabling DNS for IPv6 infrastructure

    After successful automatic distribution of IPv6 address information via DHCPv6 in your local network it might be time to start offering some more services. Usually, we would use host names in order to communicate with other machines instead of their bare IPv6 addresses. During the following paragraphs we are going to enable our own DNS name server with IPv6 address resolving. This is the third article in a series on IPv6 configuration: Configure IPv6 on your Linux system DHCPv6: Provide IPv6 information in your local network Enabling DNS for IPv6 infrastructure Accessing your web server via IPv6 Piece of advice: This is based on my findings on the internet while reading other people's helpful articles and going through a couple of man-pages on my local system. What's your name and your IPv6 address? $ sudo service bind9 status * bind9 is running If the service is not recognised, you have to install it first on your system. This is done very easy and quickly like so: $ sudo apt-get install bind9 Once again, there is no specialised package for IPv6. Just the regular application is good to go. But of course, it is necessary to enable IPv6 binding in the options. Let's fire up a text editor and modify the configuration file. $ sudo nano /etc/bind/named.conf.optionsacl iosnet {        127.0.0.1;        192.168.1.0/24;        ::1/128;        2001:db8:bad:a55::/64;};listen-on { iosnet; };listen-on-v6 { any; };allow-query { iosnet; };allow-transfer { iosnet; }; Most important directive is the listen-on-v6. This will enable your named to bind to your IPv6 addresses specified on your system. Easiest is to specify any as value, and named will bind to all available IPv6 addresses during start. More details and explanations are found in the man-pages of named.conf. Save the file and restart the named service. As usual, check your log files and correct your configuration in case of any logged error messages. Using the netstat command you can validate whether the service is running and to which IP and IPv6 addresses it is bound to, like so: $ sudo service bind9 restart $ sudo netstat -lnptu | grep "named\W*$"tcp        0      0 192.168.1.2:53        0.0.0.0:*               LISTEN      1734/named      tcp        0      0 127.0.0.1:53          0.0.0.0:*               LISTEN      1734/named      tcp6       0      0 :::53                 :::*                    LISTEN      1734/named      udp        0      0 192.168.1.2:53        0.0.0.0:*                           1734/named      udp        0      0 127.0.0.1:53          0.0.0.0:*                           1734/named      udp6       0      0 :::53                 :::*                                1734/named   Sweet! Okay, now it's about time to resolve host names and their assigned IPv6 addresses using our own DNS name server. $ host -t aaaa www.6bone.net 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: www.6bone.net is an alias for 6bone.net.6bone.net has IPv6 address 2001:5c0:1000:10::2 Alright, our newly configured BIND named is fully operational. Eventually, you might be more familiar with the dig command. Here is the same kind of IPv6 host name resolve but it will provide more details about that particular host as well as the domain in general. $ dig @2001:db8:bad:a55::2 www.6bone.net. AAAA More details on the Berkeley Internet Name Domain (bind) daemon and IPv6 are available in Chapter 22.1 of Peter Bieringer's HOWTO on IPv6. Setting up your own DNS zone Now, that we have an operational named in place, it's about time to implement and configure our own host names and IPv6 address resolving. The general approach is to create your own zone database below the bind folder and to add AAAA records for your hosts. In order to achieve this, we have to define the zone first in the configuration file named.conf.local. $ sudo nano /etc/bind/named.conf.local //// Do any local configuration here//zone "ios.mu" {        type master;        file "/etc/bind/zones/db.ios.mu";}; Here we specify the location of our zone database file. Next, we are going to create it and add our host names, our IP and our IPv6 addresses. $ sudo nano /etc/bind/zones/db.ios.mu $ORIGIN .$TTL 259200     ; 3 daysios.mu                  IN SOA  ios.mu. hostmaster.ios.mu. (                                2014031101 ; serial                                28800      ; refresh (8 hours)                                7200       ; retry (2 hours)                                604800     ; expire (1 week)                                86400      ; minimum (1 day)                                )                        NS      server.ios.mu.$ORIGIN ios.mu.server                  A       192.168.1.2server                  AAAA    2001:db8:bad:a55::2client1                 A       192.168.1.3client1                 AAAA    2001:db8:bad:a55::3client2                 A       192.168.1.4client2                 AAAA    2001:db8:bad:a55::4 With a couple of machines in place, it's time to reload that new configuration. Note: Each time you are going to change your zone databases you have to modify the serial information, too. Named loads the plain text zone definitions and converts them into an internal, indexed binary format to improve lookup performance. If you forget to change your serial then named will not use the new records from the text file but the indexed ones. Or you have to flush the index and force a reload of the zone. This can be done easily by either restarting the named: $ sudo service bind9 restart or by reloading the configuration file using the name server control utility - rndc: $ sudo rndc reconfig Check your log files for any error messages and whether the new zone database has been accepted. Next, we are going to resolve a host name trying to get its IPv6 address like so: $ host -t aaaa server.ios.mu. 2001:db8:bad:a55::2Using domain server:Name: 2001:db8:bad:a55::2Address: 2001:db8:bad:a55::2#53Aliases: server.ios.mu has IPv6 address 2001:db8:bad:a55::2 Looks good. Alternatively, you could have just ping'd the system as well using the ping6 command instead of the regular ping: $ ping6 serverPING server(2001:db8:bad:a55::2) 56 data bytes64 bytes from 2001:db8:bad:a55::2: icmp_seq=1 ttl=64 time=0.615 ms64 bytes from 2001:db8:bad:a55::2: icmp_seq=2 ttl=64 time=0.407 ms^C--- ios1 ping statistics ---2 packets transmitted, 2 received, 0% packet loss, time 1001msrtt min/avg/max/mdev = 0.407/0.511/0.615/0.104 ms That also looks promising to me. How about your configuration? Next, it might be interesting to extend the range of available services on the network. One essential service would be to have web sites at hand.

    Read the article

  • Switching to landscape mode in Android Emulator

    - by Cody
    This is probably a pretty easy to answer question, but I can't find the solution myself after a couple hours of searching the documentation and Google. I set the orientation of my Android app to landscape in the AndroidManifest.xml file: android:screenOrientation="landscape" However, when I run the app in the simulator, it appears sideways and in portrait mode. How can I switch the emulator to landscape mode on a mac? It's running the 1.6 SDK. Thanks!

    Read the article

  • emacs hexl-mode insert or delete a byte

    - by Oleg Pavliv
    How can I insert or delete a byte in hexl-mode? Suppose I have a 3-byte file "123" which is displayed as "3132 33" in hexl-mode. How can I add a byte to get "1234"? How can I remove a byte to get "12"? Using C-M-x and similar shortcuts I can replace a byte, but I want to insert and delete.

    Read the article

  • nhibernate says 'mapping exception was unhandled' no persister for: MyNH.Domain.User

    - by mrblah
    Hi, I am using nHibernate and fluent. I created a User.cs: public class User { public virtual int Id { get; set; } public virtual string Username { get; set; } public virtual string Password { get; set; } public virtual string Email { get; set; } public virtual DateTime DateCreated { get; set; } public virtual DateTime DateModified { get; set; } } Then in my mappinds folder: public class UserMapping : ClassMap<User> { public UserMapping() { WithTable("ay_users"); Not.LazyLoad(); Id(x => x.Id).GeneratedBy.Identity(); Map(x => x.Username).Not.Nullable().WithLengthOf(256); Map(x => x.Password).Not.Nullable().WithLengthOf(256); Map(x => x.Email).Not.Nullable().WithLengthOf(100); Map(x => x.DateCreated).Not.Nullable(); Map(x => x.DateModified).Not.Nullable(); } } Using the repository pattern for the nhibernate blog: public class UserRepository : Repository<User> { } public class Repository<T> : IRepository<T> { public ISession Session { get { return SessionProvider.GetSession(); } } public T GetById(int id) { return Session.Get<T>(id); } public ICollection<T> FindAll() { return Session.CreateCriteria(typeof(T)).List<T>(); } public void Add(T product) { Session.Save(product); } public void Remove(T product) { Session.Delete(product); } } public interface IRepository<T> { T GetById(int id); ICollection<T> FindAll(); void Add(T entity); void Remove(T entity); } public class SessionProvider { private static Configuration configuration; private static ISessionFactory sessionFactory; public static Configuration Configuration { get { if (configuration == null) { configuration = new Configuration(); configuration.Configure(); configuration.AddAssembly(typeof(User).Assembly); } return configuration; } } public static ISessionFactory SessionFactory { get { if (sessionFactory == null) sessionFactory = Configuration.BuildSessionFactory(); return sessionFactory; } } private SessionProvider() { } public static ISession GetSession() { return SessionFactory.OpenSession(); } } My config: <?xml version="1.0" encoding="utf-8" ?> <hibernate-configuration xmlns="urn:nhibernate-configuration-2.2"> <session-factory> <property name="connection.provider">NHibernate.Connection.DriverConnectionProvider</property> <property name="dialect">NHibernate.Dialect.MsSql2005Dialect</property> <property name="connection.driver_class">NHibernate.Driver.SqlClientDriver</property> <property name="connection.connection_string">Server=.\SqlExpress;Initial Catalog=TestNH;User Id=dev;Password=123</property> <property name="show_sql">true</property> </session-factory> </hibernate-configuration> I created a console application to test the output: static void Main(string[] args) { Console.WriteLine("starting..."); UserRepository users = new UserRepository(); User user = users.GetById(1); Console.WriteLine("user is null: " + (null == user)); if(null != user) Console.WriteLine("User: " + user.Username); Console.WriteLine("ending..."); Console.ReadLine(); } Error: nhibernate says 'mapping exception was unhandled' no persister for: MyNH.Domain.User What could be the issue, I did do the mapping?

    Read the article

  • How to find the filename of a script being run when it is executed from a symlink on linux

    - by Phil Boltt
    Hi, If I have a python script that is executed via a symlink, is there a way that I can find the path to the script rather than the symlink? I've tried using the methods suggested in this question, but they always return the path to the symlink, not the script. For example, when this is saved as my "/usr/home/philboltt/scripts/test.py" : #!/usr/bin/python import sys print sys.argv[0] print __file__ and I then create this symlink ln -s /usr/home/philboltt/scripts/test.py /usr/home/philboltt/test and execute the script using /usr/home/philboltt/test I get the following output: /usr/home/philboltt/test /usr/home/philboltt/test Thanks! Phil

    Read the article

  • proftpd, dynamic IP, and filezilla: port troubles

    - by Yami
    The basic setup: Two computers, one running proftpd, one attempting to connect via filezilla. Both linux (xubuntu on the server, kubuntu on the client). Both are at the moment behind a router on a residential (read: dynamic IP) connection; the client is a laptop I plan to take away from the home network, so I'll need this to work externally. I have my router set up to allow specific ports forwarded to each machine and, where possible, have plugged in those numbers into proftpd (via gadmin, double-checking the config file) and filezilla. Attempting to connect via active mode using the internal IP works: Status: Connecting to 192.168.1.139:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 192,168,1,52,153,140 Response: 200 PORT command successful Command: LIST Response: 150 Opening ASCII mode data connection for file list Response: 226 Transfer complete Status: Directory listing successful Attempting to connect via the domain name, however, leads to issues; in active mode, the PORT is the last command to be received according to the server's logs, and in passive mode, it's the PASV command. This leads me to believe I'm being redirected to a bad port? Active Sample: Status: Resolving address of <url> Status: Connecting to <ip:port> Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER <redacted> Response: 331 Password required for <redacted> Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PORT 174,111,127,27,153,139 Response: 200 PORT command successful Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing Passive sample: Status: Resolving address of ftp.bonsaiwebdesigns.com Status: Connecting to 174.111.127.27:8085... Status: Connection established, waiting for welcome message... Response: 220 Crossroads FTP Command: USER yamikuronue Response: 331 Password required for yamikuronue Command: PASS ******* Response: 230 Anonymous access granted, restrictions apply Command: OPTS UTF8 ON Response: 200 UTF8 set to on Status: Connected Status: Retrieving directory listing... Command: PWD Response: 257 "/" is the current directory Command: TYPE I Response: 200 Type set to I Command: PASV Response: 227 Entering Passive Mode (64,95,64,197,101,88). Command: LIST Error: Connection timed out Error: Failed to retrieve directory listing In both cases, the log file ends at "PORT" or "PASV" - there's no record of ever receiving a "LIST" command. Just above that I can see the attempt to connect actively via the internal IP, which does indeed include a LIST command. My config file includes "PassivePorts 20001-26999", which are the port forwards I set up for the ftp server, and "Port 8085", which is also forwarded to the same machine. I also have a MasqueradeAddress set up to prevent it from reporting its internal IP, which was an earlier issue I had. I think what I'm asking is, is there another setting someplace I have to change to get this setup to work?

    Read the article

  • jQuery ajax in ASP.NET with customErrors mode="On"

    - by Adrian Magdas
    Hi, any idea how to retrieve the original exception thrown on server side when doing ajax calls with jQuery and using customErrors mode="On" in web.config. If mode="Off" I can take the error using this function: error: function(xhr, status, error) { var error = JSON.parse(xhr.responseText); alert(error.Message); } Thanks, Adrian

    Read the article

  • Exception handling problem in release mode

    - by lama-power
    I have application with this code: Module Startup <STAThread()> _ Public Sub Main() Try Application.EnableVisualStyles() Application.SetCompatibleTextRenderingDefault(False) InitApp() Dim login As New LoginForm() Dim main As New MainForm() Application.Run(login) If login.DialogResult = DialogResult.OK Then ActUser = login.LoggedUser main.ShowDialog() End If DisposeApp() Catch ex As Exception ErrMsg(ex, "Error!", ErrorLogger.ErrMsgType.CriticalError) End End Try End Sub End Module in debug mode everithing is OK. But in release mode when somewhere in application exception occurs my global catch in Main method doesn`t catch exception. What is the problem please?

    Read the article

  • Refactoring a custom User model to user UserProfile: Should I create a custom UserManager or add use

    - by BryanWheelock
    I have been refactoring an app that had customized the standard User model from django.contrib.auth.models by creating a UserProfile and defining it with AUTH_PROFILE_MODULE. The problem is the attributes in UserProfile are used throughout the project to determine the User sees. I had been creating tests and putting in this type of statement repeatedly: user = User.objects.get(pk=1) user_profile = user.get_profile() if user_profile.karma > 10: do_some_stuff() This is tedious and I'm now wondering if I'm violating the DRY principle. Would it make more sense to create a custom UserManager that automatically loads the UserProfile data when the user is requested. I could even iterate over the UserProfile attributes and append them to the User model. This would save me having to update all the references to the custom model attributes that litter the code. Of course, I'd have to reverse to process for to allow the User and UserProfile models to be updated correctly. Which approach is more Django-esque?

    Read the article

  • why gcc 4.x default reserve 8 bytes for stack on linux when calling a method?

    - by nikcname
    as a beginner of asm, I am checking gcc -S generated asm code to learn. why gcc 4.x default reserve 8 bytes for stack when calling a method? func18 is the empty function with no return no param no local var defined. I can't figure out why 8 bytes is reserved here (neither any forum/site mention for the reason, ppl seems take it for granted) is it for the %ebp just push? or return type?! many thx! .globl _func18 _func18: pushl %ebp movl %esp, %ebp subl $8, %esp .text

    Read the article

  • why gcc 4.x default reserve 8 bytes for stack on linux when calling a method?

    - by nikcname
    as a beginner of asm, I am checking gcc -S generated asm code to learn. why gcc 4.x default reserve 8 bytes for stack when calling a method? func18 is the empty function with no return no param no local var defined. I can't figure out why 8 bytes is reserved here (neither any forum/site mention for the reason, ppl seems take it for granted) is it for the %ebp just push? or return type?! many thx! .globl _func18 _func18: pushl %ebp movl %esp, %ebp subl $8, %esp .text

    Read the article

  • How to execute with /bin/false shell

    - by Amar
    I am trying to setup per-user fastcgi scripts that will run each on a different port and with a different user. Here is example of my script: #!/bin/bash BIND=127.0.0.1:9001 USER=user PHP_FCGI_CHILDREN=2 PHP_FCGI_MAX_REQUESTS=10000 etc... However, if I add user with /bin/false (which I want, since this is about to be something like shared hosting and I don't want users to have shell access), the script is run under 1001, 1002 'user' which, as my Google searches showed, might be a security hole. My question is: Is it possible to allow user(s) to execute shell scripts but disable them so they cannot log in via SSH?

    Read the article

< Previous Page | 309 310 311 312 313 314 315 316 317 318 319 320  | Next Page >