Search Results

Search found 26179 results on 1048 pages for 'linux from scratch'.

Page 314/1048 | < Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >

  • ltsp-built-client error

    - by sat
    I am facing some issues while building a thin client using the ltsp-build-client, it says an error. Error is: I: Retrieving Release E: Failed getting release file file://root/ISO/ubuntu-12.04.1-desktop-i386.iso/dists/squeeze/Release error: LTSP client installation ended abnormally My Command is: ltsp-build-client --mirror file://root/ISO/ubuntu-12.04.1-desktop-i386.iso --security-mirror none --accept-unsigned-packages I am referring this URL http://wiki.debian.org/LTSP/Howto. How to solve this error?

    Read the article

  • Slapd service won't start, unable to open pid file

    - by Foezjie
    I'm trying to set up a test LDAP-server for some developers but I'm running into some trouble. service slapd start errors so I run /usr/sbin/slapd -d 1 and this gives me the following error at the end: unable to open pid file "/var/run/ldap/slapd.pid": 13 (Permission denied) slapd destroy: freeing system resources. slapd stopped. The rights for /var/run/ldap are as follows: root@pec:/var/run/ldap# ls -ld drwxr-xr-x 2 openldap openldap 60 2012-07-04 20:45 So I don't get why there is still a permission denied. Syslog gives the following when running slapd: Jul 4 21:00:27 pec slapd[13758]: @(#) $OpenLDAP: slapd 2.4.21 (Dec 19 2011 15:40:04) $#012#011buildd@allspice:/build/buildd/openldap-2.4.21/debian/build/servers/slapd Jul 4 21:00:27 pec kernel: [8147247.203100] type=1503 audit(1341428427.953:64): operation="truncate" pid=13758 parent=20433 profile="/usr/sbin/slapd" requested_mask="::w" denied_mask="::w" fsuid=0 ouid=119 name="/var/run/ldap/slapd.pid" Can anyone point me in the right direction?

    Read the article

  • Virtual bridged networking with VLAN, could not ping

    - by v.yegy
    I require a virtual network with VLAN be build between two virtual hosts - which can be (lxc/ vbox -ubuntu or win xp). I tried with lxc and vbox with Ubuntu and was finding difficult to make it work without vlan, but was successful with vbox with xp. vbox-xp1 --- br1 ---------------- br2 ---- vbox-xp2 The config is: brctl addbr br1; brctl addbr br2 ifconfig br1 up; ifconfig br2 up stp br1 off; stp br2 off ip link add name br1-br2-l0 type veth peer name br1-br2-l1 sudo brctl addif br1 br1-br2-l0 sudo brctl addif br2 br1-br2-l1 vbox - xp 1 and 2 with network ; bridged and br1 and br2 respectively. The adapter is intel PRO/1000 MT Server and driver installed in guests. Configured IPs and two hosts pinged! VLAN config: ip link add link br1 name br1-2.5 type vlan id 5 brctl addif br2 br1-2.5 create vlan 5 in xp 1 and 2 and assign ip address Ping on with this config does not work. Wireshark trace on interface br1-br2-l1 / br1-2.5 shows that one ping results in ~240 ping packets and each growing by 4 bytes - first one being correct and 60, ping does not reach other host as I see mac is not learnt[arp -a]. -- if br1-2.5 is not configured, I see untagged packets in br1-br2-l1/0, but still not reaching other host as mac is not learnt. if br1-br2-l0/1 is made down, even if br1-2.5 is up, I count not see any packets. I tried with ebtables, but still could not make a correct config to work. -- If any one here are aware of any configuration, please let me know. I need to make a network of switches. Seems I have a very long way. Sorry for a very long question. Thanks and regards, vy

    Read the article

  • How can I still see the 'man' text after I quit man?

    - by Sol
    I typically use tcsh or bash and often want to use 'man' to review a command's options. Currently when I quit man or ctrl-C, the man text disappears and I see the scrollback buffer that was there before I performed the 'man' command. I would like to still see the 'man' text I was viewing as a reference while I'm typing the command at the command prompt without opening a second window, how can I do that?

    Read the article

  • List full timestamps of files in a tarball

    - by Mechanical snail
    I have a large tar archive and want to see the exact (nanosecond) timestamps that are stored for each file in the archive. In case it's relevant, the tarball is in POSIX-2001 format (tar --format=posix). tar --list --verbose displays the timestamps rounded off to the minute. For comparison, ls --full-time does what I want, but I'd rather not have to extract everything first because it's huge. For my purposes, command-line and GUI tools are both fine.

    Read the article

  • httpd dead but subsys locked

    - by McShark
    Hello, I modified today max_execution_time in php.ini, when I restarted the server, I get this error : Stopping httpd: [FAILED] Starting httpd: (98)Address already in use: make_sock: could not bind to address [::]:80 (98)Address already in use: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs I killed httpd proc : killall httpd, and started it fine, but the I can't open any web site on the server. service httpd status OUTPUT : httpd dead but subsys locked I removed httpd file from /var/lock/subsys/ :S Same problem. Please Help!

    Read the article

  • PXE boot -- kernel not found on TFTP server

    - by user70523
    I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

    Read the article

  • page allocation failure - am I running out of memory?

    - by mfriedman
    Lately I've noticing entries like this one in the kern.log of one of my servers: Feb 16 00:24:05 aramis kernel: swapper: page allocation failure. order:0, mode:0x20 This is what I'd like to know: What exactly does that message mean? Is my server running out of memory? The swap usage is quite low (less than 10%), and so far I haven't noticed any processes being killed because of lack of memory. Additional information: The server is a Xen instance (DomU) running Debian 6.0 It has 512 MB of RAM and a 512 MB swap partition CPU load inside the virtual machine shows an average of 0.25

    Read the article

  • alternative filesystems for SSD

    - by freedrull
    I am tired of watching fsck check my filesystem when my eeepc 901 shuts down abruptly due to a crash. I know that with a journaling filesystem, I won't have to wait for a check. However, I am well aware of the poor I/O performance of the SSD, so I can imagine using a journaling filesystem being even more frustrating, since there will be constant writes to the journal? I will buy a new laptop without such a crummy ssd someday but, is there anything I can do now, on the software side of things?

    Read the article

  • Network is going down once per day

    - by Charly
    Once per day the network on eth0 is going down and we need to do sudo ifdown eth0; sudo ifup eth0 to get the network up. Here is the syslog: Feb 11 12:48:01 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 12:52:35 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 12:56:23 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:00:28 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:04:29 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:09:16 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:13:53 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:18:16 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:22:25 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:26:52 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:30:44 www-tech-1 dhclient: DHCPREQUEST of address> on eth0 to 131.121.113.228 port 67 Feb 11 13:31:49 www-tech-1 dhclient: There is already a pid file /var/run/dhclient.eth0.pid with pid 3198 Feb 11 13:31:49 www-tech-1 dhclient: Listening on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:49 www-tech-1 dhclient: Sending on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:49 www-tech-1 dhclient: DHCPRELEASE on eth0 to 131.121.113.228 port 67 Feb 11 13:31:49 www-tech-1 dhclient: There is already a pid file /var/run/dhclient.eth0.pid with pid 134519072 Feb 11 13:31:50 www-tech-1 dhclient: Listening on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:50 www-tech-1 dhclient: Sending on LPF/eth0/00:e0:81:49:fc:e0 Feb 11 13:31:52 www-tech-1 dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 8 Feb 11 13:31:52 www-tech-1 dhclient: DHCPREQUEST of 131.121.14.17 on eth0 to 255.255.255.255 port 67 Feb 11 13:31:53 www-tech-1 kernel: [265383.991682] eth0: no IPv6 routers present Please check the last portion of this syslog. Can anybody help me?

    Read the article

  • Wicd not playing well with networks that utilize network access control

    - by Sion
    Starting a couple months ago (might be able to find exact date if necessary) my installation of Wicd stopped being able to see wireless networks that use NAC (Network Access Control) such as Aruba networks. But if I shut down Wicd and start NetworkManager I can connect to said networks and log in to them depending on what the NAC requires. This is the current wicd package installed: net-misc/wicd-1.7.1_pre20111210-r1 This is how I manipulate the network manager running: su -c'/etc/init.d/wicd stop; /etc/init.d/NetworkManager start' What would cause this specific of a problem to occur?

    Read the article

  • o2cb thinks ocfs2 cluster is still online, and refuses to shut down

    - by Kendall
    I have a handful of OpenSuSE 11.2 servers that utilize OCFS2 volumes. I've noticed that o2cb can't figure out when the OCFS2 cluster is actually mounted. For example, when I try to shutdown o2cb, after stopping OCSF2, o2cb refuses to shutdown because it thinks OCFS2 is still up! After stopping OCFS2 I try to stop o2cb... hamguy:/dev/disk/by-label # /etc/init.d/o2cb stop Stopping O2CB cluster ocfs2: Failed Unable to stop cluster as heartbeat region still active So I check the status... hamguy:/dev/disk/by-label # /etc/init.d/o2cb status Driver for "configfs": Loaded Filesystem "configfs": Mounted Stack glue driver: Loaded Stack plugin "o2cb": Loaded Driver for "ocfs2_dlmfs": Loaded Filesystem "ocfs2_dlmfs": Mounted Checking O2CB cluster ocfs2: Online Heartbeat dead threshold = 31 Network idle timeout: 30000 Network keepalive delay: 2000 Network reconnect delay: 2000 Checking O2CB heartbeat: Active And double check OCFS2... hamguy:/dev/disk/by-label # /etc/init.d/ocfs2 status Configured OCFS2 mountpoints: /u/conf /u/logs /u/backup /u/client /u/data /u/mdata OCFS2 is clearly down, while o2cb clearly thinks otherwise. The versions of OCFS2 and o2cb are... kendall@hamguy:~> rpm -qa |grep ocfs2 ocfs2console-1.4.1-25.6.x86_64 ocfs2-tools-o2cb-1.4.1-25.6.x86_64 ocfs2-tools-1.4.1-25.6.x86_64 kendall@hamguy:~> rpm -qa |grep o2cb ocfs2-tools-o2cb-1.4.1-25.6.x86_64 What causes this, and is there a way around it? If I try to reboot the machine, it will just sit there forever until your physically power cycle it. That obviously is a bit of a problem. Any insight is appreciated, thank you. Kendall

    Read the article

  • Debian Unstable + Postfix 2.6.5 + dkim-filter 2.8.2 issue

    - by kura
    I have Postfix installed on Debian Unstable, as the title states, the system is completely up-to-date, I have tried to get DKIM signatures working on outgoing mail using dkim-filter 2.8.2. I couldn't use the default Debian way of doing things with sockets, instead I used the Ubuntu way: SOCKET="inet:12345@localhost"` I have the following in my postfix/main.cf milter_default_action = accept milter_protocol = 6 smtpd_milters = inet:localhost:12345 non_smtpd_milters = inet:localhost:12345 All is fine except I get the following message I start DKIM in mail.log: dkim-filter[22029]: can't configure DKIM library; continuing And when it tries to sign mails I get the following error: postfix/cleanup[22042]: warning: milter inet:localhost:12345: can't read SMFIC_EOH reply packet header: Success And then dkim-filter daemon stops. I've looked through Google but found no actual way to fix this that works for me. I have this working fine on an Ubuntu server but would love to get it working on Debian too.

    Read the article

  • Sorting by date

    - by user62367
    Original: Jan 23 2011 10:42 SOMETHING 2007.12.20.avi Jun 26 2009 SOMETHING 2009.06.25.avi Feb 12 2010 SOMETHING 2010.02.11.avi Jan 29 2011 09:17 SOMETHING 2011.01.27.avi Feb 11 2011 20:06 SOMETHING 2011.02.10.avi Feb 27 2011 23:05 SOMETHING 2011.02.24.avi Output: Feb 27 2011 23:05 SOMETHING 2011.02.24.avi Feb 11 2011 20:06 SOMETHING 2011.02.10.avi Jan 29 2011 09:17 SOMETHING 2011.01.27.avi Jan 23 2011 10:42 SOMETHING 2007.12.20.avi Feb 12 2010 SOMETHING 2010.02.11.avi Jun 26 2009 SOMETHING 2009.06.25.avi How could I get the output where the newest file is at the top?

    Read the article

  • How to change MySQL data directory?

    - by Jonathan Frank
    I want to place my databases in another directory, so I can store them in an ESB (elastic block storage, just a fancy name for a virtualized harddisk) together with my web-apps and other persistent data. I have tried to walk through a tutorial at http://crashmag.net/change-the-default-mysql-data-directory-with-selinux-enabled. Everything seems fine until I type this command: # semanage fcontext -a -t mysqld_db_t "/srv/mysql(/.*)?" Then the command fails and tells me that mysqld_db_t is an invalid SELinux context even if the default MySQL data directory is labelled with this context. I am running Fedora 15 on Virtualbox (behaves like an ordinary x86-compatible box) and Amazon EC2 (based on Xen) so the tutorial should be compatible. It is also worth to mention that turning off SELinux globally or just for the MySQL process is not an option, because such a solution will decrease the security of the system if a hacker gains access to the system via the MySQL server. I have never seen this problem before I changed to the Redhat/Fedora architecture, so it could be a distribution specific issue. Any help is highly appreciated

    Read the article

  • Tomcat fails to start, no logs or error provided

    - by Alex Kuhl
    I have a Centos5 box running tomcat5 (a version before 5.5, there's no bin/version.sh script). When attempting to start tomcat, whether through init.d or service, I get the FAILED message with no other information provided. The date on catalina.out changes but it has no contents and is 0 bytes. logging.conf has not been edited and everything is marked as FINE detail. Has anyone experienced this and know of a solution? Or, failing that, how can I get some log/error info from tomcat to try to pinpoint the issue?

    Read the article

  • How do I automate OS installation on 500+ machines?

    - by Igor
    My company has to image a large amount of machines by the end of the year. Each of the machines will have hardware RAID 1 and running CentOS 6. What options do I have for automating the OS installation on these systems? I have a little mini desktop I can set up as an install server, and we can get a switch to create an installation network, but I'm not sure how to go about actually performing the automated installs.

    Read the article

  • Sendmail Sends but never Delivers

    - by Jeremy
    I have tried 10 different emails hosted at Google, Yahoo!, GoDaddy, and some that are privately hosted, and each time I get the following errors. I have blocked sensitive information, but you will be able to see the errors. Feb 16 17:06:50 xxxxx sendmail[31824]: o1GM6ovJ031824: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30054, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GM6oJo031825 Message accepted for delivery) Feb 16 16:54:19 xxxxx sendmail[31625]: o1GLsJPP031625: [email protected], ctladdr=www-data (33/33), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=30097, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (o1GLsJah031626 Message accepted for delivery) Feb 17 09:05:52 xxxxx sm-mta[10620]: o1H6Z3jM005734: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=07:30:49, xdelay=01:15:36, mailer=esmtp, pri=571331, relay=aspmx3.googlemail.com. [209.85.222.4], dsn=4.0.0, stat=Deferred: Connection timed out with aspmx3.googlemail.com. Feb 17 10:35:23 xxxxx sm-mta[12828]: o1HEZwn8011833: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=00:59:25, xdelay=00:12:36, mailer=esmtp, pri=300353, relay=aln-mailrelay.att.net. [12.102.252.75], dsn=4.0.0, stat=Deferred: Connection timed out with aln-mailrelay.att.net. If you take a look, they all send, but then (HOURS later) I get an error "stat=Deferred: Connection timed out with {server}". I'm at my wits end, because I use this same setup on each of my servers, and they all work.

    Read the article

  • Best MTA setup for home or laptop computers - not server

    - by thomasrutter
    Hello, What is a good MTA (e.g. Postfix or something else) setup for a home computer behind a NAT, or a laptop that connects to various different wifi networks? I've read a lot of Postfix tutorials on how to set it up this way or that, but they are usually geared towards computers that are servers ie they have a static IP have a domain name are always connected to the same network My requirements are, I guess: Ability to forward mail for "root" to another server of my choosing. No listening for incoming SMTP connections - outgoing only Ability to route outgoing mail via an external SMTP server with authentication (and perhaps encryption) If not Postfix, I need an MTA which can queue up mails in case it temporarily has no internet connection.

    Read the article

  • An XKB keyboard map that responds to the left and right shift key individually

    - by mbfisher
    First off, excuse my ignorance of X and XKB; I've been trying to hack together a solution in the hope of being able to achieve what I want without requiring a detailed grasp of it. I'm trying to create an XKB keyboard map on Ubuntu 12.04 that allows me to stipulate which of the two shift keys constitutes the Level2 modifier. Specifically, the 4 key should only produce a $ when the right shift is held, not the left. My reading so far: http://www.charvolant.org/~doug/xkb/html/node5.html http://people.uleth.ca/~daniel.odonnell/Blog/custom-keyboard-in-linuxx11 http://www.x.org/releases/X11R7.5/doc/input/XKB-Enhancing.html Lots of searching! I've attempted to define a custom type, and then refer to it explicitly in a symbols map: /usr/share/X11/xkb/types/mbfisher: default xkb_types "mbfisher" { type "RIGHT_SHIFT" { modifiers = None+Shift_R; map[None] = Level1; map[Shift_R] = Level2; }; } /usr/share/X11/xkb/symbols/mbfisher: default partial alphanumeric_keys xkb_symbols "basic" { name[Group1]= "mbfisher"; key <AE04> { type= "RIGHT_SHIFT", symbols[Group1]= [ 4, dollar ] }; }; I'm then selecting the map with the Ubuntu Keyboard Layout GUI. This obviously disables the alphanumeric keyboard apart from the 4 key, but the dollar sign can still be typed with either shift key. I'm conscious of writing a massive question with lots of useless information so I'll stop here; please ask for anything I've missed out. Any ideas?

    Read the article

  • How to (hardware) RAID 10 on Ubuntu 10.04 LTS with 4 drives and motherboard with RAID contoller

    - by lollercoaster
    I have 4 500GB hard drives. I set up a RAID 10 in BIOS, much like shown here: http://www.supermicro.com/manuals/other/RAID_SATA_ESB2.pdf Then I followed these instructions: http://www.unrest.ca/Knowledge-Base/configuring-mdadm-raid10-for-ubuntu-910 Basically I cannot get it to work. I go through the instructions when I get to the "partition" section of the install, creating 4 RAID 1's (2 partitions on each drive, one for primary and one for swap space), then combining to make a RAID 10. Unfortunately it still shows 2 partitions, one 500 GB and another being 36GB for some reason. Any ideas? I think best would be if anyone had found good instructions (step by step) for how to do this...I've been googling for hours and haven't found anything...

    Read the article

  • Password rules for yppasswd

    - by gstoynev
    Hello all, I have a NIS master-slave setup and I would like to improve the password rules/complexity for it. Seems like if I introduce new rules to the NIS Master they are applicable only from there. What I mean: I want minimal password length of 9 characters. On the NIS master if I run 'passwd' it obeys this requirement. If I run 'yppasswd' it just go to the default 6 characters. If I use 'chage -d 0 user1' to force a user to change a password, the user is prompted only when login on the NIS Master. The user's old password is still good to login at NIS clients. All machines are running Ubuntu 9.10 or 10.04. How I can strengthen yppasswd rules and make it warn users to change their passwords? Thank you all!

    Read the article

< Previous Page | 310 311 312 313 314 315 316 317 318 319 320 321  | Next Page >