Search Results

Search found 12038 results on 482 pages for 'controller actions'.

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

Page 318/482 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

  • FreeNas running on ESXi - sometimes gets very slugish.

    - by Luma
    Hello everyone, I have a ESXi server (dual quad core, 8GB of DDR3 ram, 6x 1TB WD Blacks running in RAid 5 on the PErc 6/i controller. I have a 64bit freenas VM running, on this VM I keep about 200Gigs of stuff that my windows machines access. every now and then the throughput of this VM just dies, for example right now it can't even handle streaming a song and when I tried to transfer a folder the speed goes from 10-400KB/s. Might I add at this point that the ESXi box has dual gigabit network cards plugged into a good solid gigabit switch and other linux and windows VM's are just fine I have seen speeds over 90MB/s (frequently) The server still has ram left over (plenty actually) and cpu is very low (500-1000mhz) any ideas what could cause this? thanks. Luc

    Read the article

  • CentOS - Add additional hard drive raid arrays on Dell Perc 5/i card

    - by Quanano
    We have a Dell Poweredge 2900 system with Dell Perc 5/i card and 4 SAS hard drives attached, with NTFS partitions on them. We installed CentOS on one raid array on this controller with a different controller and it is working fine. We are now trying to access the drives shown above and they are not being shown in /dev as sdb, etc. sda is the drive that we installed centos on and it has sda1, sda2, sda3, etc. The CDROM has been picked up as well. If I scan for scsi devices then the perc and adaptec controllers are both found. sg0 is the CDROM and sg2 is the centos installed, however I think sg1 is the other drive but I cannot see anyway to mount the partitions, as only the drive is listed in /dev. Thanks. EXTRA INFO fdisk -l: Disk /dev/sda: 72.7 GB, 72746008576 bytes 255 heads, 63 sectors/track, 8844 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x11e3119f Device Boot Start End Blocks Id System /dev/sda1 * 1 64 512000 83 Linux Partition 1 does not end on cylinder boundary. /dev/sda2 64 8845 70528000 8e Linux LVM Disk /dev/mapper/vg_lal2server-lv_root: 34.4 GB, 34431041536 bytes 255 heads, 63 sectors/track, 4186 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_root doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_swap: 21.1 GB, 21139292160 bytes 255 heads, 63 sectors/track, 2570 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_swap doesn't contain a valid partition table Disk /dev/mapper/vg_lal2server-lv_home: 16.6 GB, 16647192576 bytes 255 heads, 63 sectors/track, 2023 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00000000 Disk /dev/mapper/vg_lal2server-lv_home doesn't contain a valid partition table These are all from the install hdd not the additional hard drives modprobe a320raid FATAL: Module a320raid not found. lsscsi -v: [0:0:0:0] cd/dvd TSSTcorp CDRWDVD TS-H492C DE02 /dev/sr0 dir: /sys/bus/scsi/devices/0:0:0:0 [/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0] [4:0:10:0] enclosu DP BACKPLANE 1.05 - dir: /sys/bus/scsi/devices/4:0:10:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:0:10/4:0:10:0] [4:2:0:0] disk DELL PERC 5/i 1.03 /dev/sda dir: /sys/bus/scsi/devices/4:2:0:0 [/sys/devices/pci0000:00/0000:00:05.0/0000:01:00.0/0000:02:0e.0/host4/target4:2:0/4:2:0:0] . lsmod: Module Size Used by fuse 66285 0 des_generic 16604 0 ecb 2209 0 md4 3461 0 nls_utf8 1455 0 cifs 278370 0 autofs4 26888 4 ipt_REJECT 2383 0 ip6t_REJECT 4628 2 nf_conntrack_ipv6 8748 2 nf_defrag_ipv6 12182 1 nf_conntrack_ipv6 xt_state 1492 2 nf_conntrack 79453 2 nf_conntrack_ipv6,xt_state ip6table_filter 2889 1 ip6_tables 19458 1 ip6table_filter ipv6 322029 31 ip6t_REJECT,nf_conntrack_ipv6,nf_defrag_ipv6 bnx2 79618 0 ses 6859 0 enclosure 8395 1 ses dcdbas 9219 0 serio_raw 4818 0 sg 30124 0 iTCO_wdt 13662 0 iTCO_vendor_support 3088 1 iTCO_wdt i5000_edac 8867 0 edac_core 46773 3 i5000_edac i5k_amb 5105 0 shpchp 33482 0 ext4 364410 3 mbcache 8144 1 ext4 jbd2 88738 1 ext4 sd_mod 39488 3 crc_t10dif 1541 1 sd_mod sr_mod 16228 0 cdrom 39771 1 sr_mod megaraid_sas 77090 2 aic79xx 129492 0 scsi_transport_spi 26151 1 aic79xx pata_acpi 3701 0 ata_generic 3837 0 ata_piix 22846 0 radeon 1023359 1 ttm 70328 1 radeon drm_kms_helper 33236 1 radeon drm 230675 3 radeon,ttm,drm_kms_helper i2c_algo_bit 5762 1 radeon i2c_core 31276 4 radeon,drm_kms_helper,drm,i2c_algo_bit dm_mirror 14101 0 dm_region_hash 12170 1 dm_mirror dm_log 10122 2 dm_mirror,dm_region_hash dm_mod 81500 11 dm_mirror,dm_log blkid: /dev/sda1: UUID="bc4777d9-ae2c-4c58-96ea-cedb342b8338" TYPE="ext4" /dev/sda2: UUID="j2wRZr-Mlko-QWBR-BndC-V2uN-vdhO-iKCuYu" TYPE="LVM2_member" /dev/mapper/vg_lal2server-lv_root: UUID="9238208a-1daf-4c3c-aa9b-469f0387ebee" TYPE="ext4" /dev/mapper/vg_lal2server-lv_swap: UUID="dbefb39c-5871-4bc9-b767-1ef18f12bd3d" TYPE="swap" /dev/mapper/vg_lal2server-lv_home: UUID="ec698993-08b7-443e-84f0-9f9cb31c5da8" TYPE="ext4" dmesg shows: megaraid_sas: fw state:c0000000 megasas: fwstate:c0000000, dis_OCR=0 scsi2 : LSI SAS based MegaRAID driver scsi 2:0:0:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:1:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:2:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:3:0: Direct-Access SEAGATE ST3146855SS S527 PQ: 0 ANSI: 5 scsi 2:0:4:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:5:0: Direct-Access HITACHI HUS154545VLS300 D590 PQ: 0 ANSI: 5 scsi 2:0:8:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 scsi 2:0:9:0: Direct-Access FUJITSU MBA3073RC D305 PQ: 0 ANSI: 5 i.e. the 3 RAID Arrays Seagate Hitatchi and Fujitsu hard drives respectively. FURTHER UPDATE I have installed the megaraid storage manager console and connected to the server. It appears that the two CentOS installation hard drives are OK. The other 6 drives, one raid array of 4 and one raid array of 2 disks. The other drives are listed as (Foreign) Unconfigured Good.

    Read the article

  • HP DL380 G5 Predictive Drive Failure on a new drive

    - by CharlieJ
    Consolidated Error Report: Controller: Smart Array P400 in slot 3 Device: Physical Drive 1I:1:1 Message: Predictive failure. We have an HP DL380 G5 server with two 72GB 15k SAS drives configured in RAID1. A couple weeks ago, the server reported a drive failure on Drive 1. We replaced the drive with a brand new HDD -- same spares number. A few days ago, the server started reporting a predictive drive failure on the new drive, in the same bay. Is it likely the new drive is bad... or more likely we have a bay failure problem? This is a production server, so any advice would be appreciated. I have another spare drive, so I can hot swap it if this is a fluke and new drive is just bad. THANKS! CharlieJ

    Read the article

  • HP Proliant DL360 G5 + MSA50 RAID Setup recommendations

    - by JohnRB
    I am running a HP Proliant DL360 2 x 3GHz Xeon 16GB Ram P400 integrated RAID card with 6 x 73GB SAS HDDs running Ubuntu Server 14.04 CLI only. I recently got my hands on a MSA50 SAS Enclosure (10 x SAS HDD bays w/ SAS in/out interface) and wondering what you guys recommended as far as an addon raid controller for one of the pciex slots. I have both slots free Full and Half sizes. Any suggestions are greatly appreciated, I am an I.T. Consultant but have not used these particular units before so I was hoping to hear from someone who has. Thanks!

    Read the article

  • Laptop stopped recognizing USB hard drive

    - by vahokif
    Hi, My Packard Bell EasyNote TX86 laptop stopped recognizing my 1 TB Toshiba Store Art hard drive. It worked fine until now, and it still works on other computers. Other USB devices (including storage) work, and I've tried plugging it in every port, to no avail. When I plug it in it spins up, but Windows doesn't react at all (it's not in disk management), Linux doesn't write anything in dmesg and I can't see it in BIOS setup. I didn't use it at all today, apart from plugging it into a freshly-installed Windows 7 machine once (where it worked). What can I do? Which device is to blame here? EDIT: One more thing. I unplugged the drive while the laptop was hibernated. Google says this might be the problem and it might have something to do with resetting the USB Host Controller.

    Read the article

  • OpenVPN Configuration - Windows 7 client & debian server

    - by Guillaume
    I recently formatted my Windows 7 computer and lost my client's config files for OpenVPN. I recovered the certificates and default config that were left on the server but I haven't managed to make the whole thing work again. I assume the server's config and routing table are OK because it was working before (although quite some time ago). Would any of you experts be able to help? server.conf # Serveur TCP/666 mode server proto udp port 666 dev tun # Cles et certificats ca ca.crt cert server.crt key server.key dh dh1024.pem tls-auth ta.key 0 cipher AES-256-CBC # Reseau server 10.8.0.0 255.255.255.0 #push "redirect-gateway def1 bypass-dhcp" push "dhcp-option DNS 208.67.222.222" push "dhcp-option DNS 208.67.220.220" push "redirect-gateway def1" keepalive 10 120 # Securite user nobody group nogroup chroot /etc/openvpn/jail persist-key persist-tun comp-lzo # Log verb 3 mute 20 status openvpn-status.log log-append /var/log/openvpn.log client.conf # Client client dev tun proto udp remote *my server's ip address*:666 cipher AES-256-CBC # Cles ca ca.crt cert client1.crt key client1.key tls-auth ta.key 1 # Securite nobind persist-key persist-tun comp-lzo verb 3 Routing table on debian server when OpenVPN server is running: Destination Gateway Genmask Indic Metric Ref Use Iface 10.8.0.2 * 255.255.255.255 UH 0 0 0 tun0 10.8.0.0 10.8.0.2 255.255.255.0 UG 0 0 0 tun0 my server's ip * 255.255.255.0 U 0 0 0 eth0 default 72815.trg.dedic 0.0.0.0 UG 0 0 0 eth0 Routing table on Windows 7 client (OpenVPN not working) =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 =========================================================================== Persistent Routes: None IPv6 Route Table =========================================================================== Active Routes: [...] =========================================================================== Persistent Routes: None And when the link is established between my client and the server: The server's routing table stays the same. The client's becomes: =========================================================================== Interface List 19...00 f0 8a 1b 6e 5c ......TAP-Win32 Adapter V9 12...90 2e 34 33 84 7b ......Atheros AR8151 PCI-E Gigabit Ethernet Controller ( NDIS 6.20) 1...........................Software Loopback Interface 1 12...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter 13...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface 16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2 =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.11 20 0.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 10.8.0.1 255.255.255.255 10.8.0.5 10.8.0.6 30 10.8.0.4 255.255.255.252 On-link 10.8.0.6 286 10.8.0.6 255.255.255.255 On-link 10.8.0.6 286 10.8.0.7 255.255.255.255 On-link 10.8.0.6 286 my server's ip 255.255.255.255 192.168.1.1 192.168.1.11 20 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 128.0.0.0 128.0.0.0 10.8.0.5 10.8.0.6 30 192.168.1.0 255.255.255.0 On-link 192.168.1.11 276 192.168.1.11 255.255.255.255 On-link 192.168.1.11 276 192.168.1.255 255.255.255.255 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.1.11 276 224.0.0.0 240.0.0.0 On-link 10.8.0.6 286 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.1.11 276 255.255.255.255 255.255.255.255 On-link 10.8.0.6 286 =========================================================================== Persistent Routes: None What's working: Server and client do connect to each other, SSL certificates are OK. The client gets an IP (10.8.0.6) from the server OpenVPN client is started as an administrator. But: I cannot ping the other one on either side. 'Gateway' value is empty on client's side (in the adapter's "status" window). Client has got no internet access when the link is up. Ideal configuration: I only want the client to be able to use the server's Internet access and access its resources (MySQL server in particular). I do not need or want the server to access the client's local network. The client needs to be able to access it's local network, although all Internet traffic should be redirected to the VPN link. I spent a considerable amount of time on this but it's still not working, any help would be much appreciated. Thanks :)

    Read the article

  • Machine account authentication on Radius server

    - by O.Shevchenko
    My workstation is under Linux. I have an Active Directory domain controller + Radius server on Windows 2008. I can verify user account 'radius-01' using 'radtest' tool: $ radtest -t pap radius-01 password123 195.234.133.32 1812 password123 Sending Access-Request of id 98 to 195.234.73.2 port 1812 User-Name = "radius-01" User-Password = "password123" NAS-IP-Address = 127.0.1.1 NAS-Port = 1812 rad_recv: Access-Accept packet from host 195.234.133.32 port 1812, id=98, length=84 Framed-MTU = 1344 Framed-Protocol = PPP Service-Type = Framed-User Class = 0x537004f00000013700010200ac1c0... I have joined my Linux PC to Active Directory domain ARB-HRK using Samba: [root@shev-arb]# net ads testjoin Join is OK I can dump machine password: [root@shev-arb]# tdbdump /var/lib/samba/private/secrets.tdb { key(34) = "SECRETS/MACHINE_PASSWORD/ARB-HRK" data(15) = "yGgXJsquRnpT0g\00" } How can i authenticate my machine account on Radius server? Do anybody know any tools for this, like: radtest shev-arb$ yGgXJsquRnpT0g 195.234.133.32 1812 password123 (this command fails)

    Read the article

  • LUNS access issue in ESX4 Cluster server

    - by rmustafa
    HI, I've created volumes in equallogic in PS 6000 XV(having 2 member which is in 1 pool), checked & those volumes can be easily detected my ISCSI software in windows. But the problem with ESX , not able to see the assigned disk on ESX server, I can explain what I've done: 1.Created Cluster with enabled HA & DRS 2.Added 3 ESX4 HOST 3.Added VMkernel & configured in all 3 ESX4, enabled vmotion & FT on the same adapter. 4.went to iSCSI storage adapter properties, enabled iSCSI 5.Trying to discover the available storage with the controller IP on dynamic discovery, but not able to see the assigned storage Note: the same volume is accessed to windows that means there is no issue from storage , am I right ???? Note: I wanted to mount the same volume in all 3 ESX host. Please suggest .... Thanks & Regards, Rashid Mustafa

    Read the article

  • Unix domain socket firewall

    - by lagab
    Hello, everyone. I've got a problem with my debian server. Probably there is some vulnerable script at my web-serser, which is running from www-data user. I also have samba with winbind installed, and samba is joined to windows domain. So, probably this vulnerable script allows hacker to bruteforce out domain controller through winbind unix domain socket. Actually I have lots of such lines at netstat -a output: unix 3 [ ] STREAM CONNECTED 509027 /var/run/samba/winbindd_privileged/pipe And our DC logs contain lots of recorded authentication attems from root or guest accounts. How can I restrict my apaches access to winbind? I had an idea to use some kind of firewall for IPC sockets. Is it possible?

    Read the article

  • Wireless router not connection -> AP Not associated

    - by candido
    I can not connect to internet by wireless router after some months with ubuntu 10.04. I can connect with the same portable but with win OS. My SO is ubuntu 10.04 linux 2.6.32-41 arch SMP i686. The internet wireless network controller is Atheros AR9285 chipset (pci express) Kernel module ath9k I have tried a command line connection: $ sudo /etc/init.d/network-manager stop #stop gui network manager $ iwconfig wlan0 essid WLAN_3C key s:C001D20550B3C $ ifconfig Access Point: NOT-ASSOCIATED $dmesg ... AP 00:1a:2b:08:60:49 associated Is the SO has connected to router for booting long ( associated message), after boot and login why the connection to router is not possible by network-manager or command line (NOT associated message)? Thanks in advance

    Read the article

  • Need advice to choose correct wi-fi drivers for Dell Vostro 3560

    - by overdriven
    I'm having problems with my Dell notebook's Wi-Fi, it can't see some of the available access points, despite they are close and I used to be connected to them yesterday. Other notebooks and my phone can see them. I believe it's a driver issue, since after installing system I haven't downloaded any network drivers. I went to Dell's website to search for them but I have no idea which should I choose. For my Dell Vostro 3560 and system Windows 8.1 64bit these are available: Intel Smart Connect Technology Application APP_iSCT_W8.1_A00_Setup-TJW84_ZPE.exe (23 MB) Vostro-3560_Network_Application_TJW84_WN_4.2.40.2418_A00.EXE (29 MB) Dell Wireless 1704 WLAN 802.11b/g/n (2.4GHz), Bluetooth v4.0+HS Driver DW1704_W8.1_A00_Setup-K1HGN_ZPE.exe (239 MB) Network_Driver_K1HGN_WN_6.30.223.143_A00.EXE (247 MB) Dell Wireless1703 802.11 b/g/n, BT4.0 + HS Driver Dell Wireless1901 802.11a/b/g/n (2.4GHz and 5GHz), Bluetooth v4.0+HS Driver DW1703_DW1901_Win8.1_A00_Setup-7FPWR_ZPE.exe (265 MB) Network_Driver_7FPWR_WN_10.0.0.263_A00.EXE (272 MB) Realtek RTL8105E/RTL8111E Ethernet Controller Driver LOM_Realtek_W8.1_A00_Setup-0XCVW_ZPE.exe (6 MB) Network_Driver_0XCVW_WN_8.018.0621.2013_A00.EXE (12 MB) Intel® Centrino® Wireless-N 2230 Bluetooth Driver BT_Intel_W8.14_A00_Setup-XR83W_ZPE.exe (31 MB) Network_Application_XR83W_WN_3.1.1307.0362_A00.EXE (37 MB)

    Read the article

  • Windows Server 2008 R2 DNS Server not working?

    - by wolfvilleian
    I have a server running Windows Server 2008 R2 hosting a DNS server, exchange 2010 and is a domain controller. One computer on the network (and domain) can ping the server 25% of the time, also when I try to ping it's own hostname it also does not work. However another computer that is on the domain can ping it fine, and another computer on the network but not domain can ping fine as well. The computer that cannot ping the server is setup to use the DNS server running on the server only (secondary dns points to nothing) and it will resolve the hostname of the server to the external IP not internal when the other two computers correctly resolve the internal All 3 computers and server are connected directly into the same switch. Does anyone have any ideas on how to fix this? Thanks

    Read the article

  • b43 module loaded, but no interface showed up

    - by Eduardo Bezerra
    I'm using CentOS 6.3 x86_64 on a hardware with a BCM43224 chip for wi-fi. I installed the b43-fwcutter module and then run modprobe b43, with no error messages. However, no new network interface showed up, and the return of iwconfig is: lo no wireless extensions. eth0 no wireless extensions. lspci -nn | grep 43224 returns: 03:00.0 Network controller [0280]: Broadcom Corporation BCM43224 802.11a/b/g/n [14e4:4353] (rev 01) and uname -a: Linux localhost.localdomain 2.6.32-279.14.1.el6.x86_64 #1 SMP Tue Nov 6 23:43:09 UTC 2012 x86_64 x86_64 x86_64 GNU/Linux Any ideas of how to make the wireless device work?

    Read the article

  • Setting up Kerberos SSO in Windows 2008 network

    - by Arturs Licis
    We recently introduced Kerberos (SPNEGO) Single Sign-on in our web-portal, and tested it on a Windows network with Windows 2003 domain controller. Now, trying to test it on Windows 2008 R2 controlled network, SSO just doesn't work due to defective tokens. Up to the moment I was pretty sure that there's something wrong about environment and that were NTLM tokens. We double checked IE settings etc, but nothing helped. Then we checked the following settings for both users (logged on a client test-machine, and the one used as a Service Principal): This account supports Kerberos AES 128 bit encryption. This account supports Kerberos AES 256 bit encryption. .. and error message changed to ' GSSException: Failure unspecified at GSS-API level (Mechanism level: Encryption type AES256CTS mode with HMAC SHA1-96 is not supported/enabled) It makes me think that Internet Explorer receives Kerberos tokens at all times, and there's just some configuration missing, or it was ktpass.exe to be incorrectly executed. Here's how ktpass.exe was invoked: C:ktpass /out portal1.keytab /mapuser USER /princ HTTP/[email protected] /pass *

    Read the article

  • How to fix: mac keyboard ignores "first" key pressed

    - by lexu
    UPDATE 2012.03.19: the MBP described in this post is now broken and recycled (logic board fried). The replacement doesn't manifest the same problems. I tend to believe the problem originated in the keyboard firmware of the old MBP. Every now and then, usually after I haven't pressed a key in some time, sometimes minutes, sometimes seconds, my MBP will "swallow" the the first key I press ... say I'm logging into "superuser.com" .. I start typing my username and the textbox will show "exu" instead of "lexu" This is driving me nuts! My guess is the keyboard or it's controller goes to sleep and fails to wake up propperly ... What can I do about this? PS: I've already installed "MacBook, MacBook Pro Keyboard Firmware Update 1.0"

    Read the article

  • Cannot authenticate a domain user with SQL Server 2008

    - by Sambo
    I'm new to setting up Domains so I might be missing something simple here... I've installed SQL Server 2008 on a Windows Server 2008 R2 box and I have another WS2008 R2 box acting as the domain controller. I've joined the SQL server to the domain and it seems to be behaving itself fine. I can ping the DC by name and IP address. I created a domain user 'SPSQLAdmin' that I want to use for database access with SharePoint but I can't seem to log on to SQL with this user. SQL complains, saying that the user belongs to an untrusted domain. I've configured the DC to delegate control for any service to the SQL Server but it doesn't improve the situation. What should I try next? Thanks in advance.

    Read the article

  • MDADM RAID5 array showing as CLEAN FAULTY

    - by Dean Reilly
    A drive dropped out of my raid 5 array yesterday. It looks like the reason was due to a bad controller so I switched it out and attempted to re-add the drive but mdadm claimed it couldn't do it. So I zerod the superblock and just added the drive normally and left it to resync. When I came to check on the array this morning I was unable to mount it at all and it's now showing as CLEAN FAULTY with two drives missing. The two missing drives are listed as spare and faulty spare. Is there anything I can do in this situation or is the array gone?

    Read the article

  • IE does not send NTLM domain

    - by Buddy Casino
    Hi! I have a problem with NTLM single-sign-on with IE8. We've got multiple domain controllers and users from multiple domains that we try to authenticate to a web application via NTLMv1 passthru. Somehow IE fails to send the user's domain in the NTLM Type 1 message. This has the effect that the webapp can not match users properly to their domain controllers, resulting in failed logon attempts, because a user from domain X tries to authenticate to domain controller Y. This problem does not occur with Firefox, as it always sends the correct domain header. So: how do I get IE to send the domain in the NTLM header? Grateful for any help, Michael

    Read the article

  • Windows 8, NVIDIA graphics recognition fails

    - by Roy Grubb
    I just installed Windows 8 Pro OEM 64-bit (clean install) and it won't properly recognize my graphics adapter. When I installed Win8, it automatically installed the BasicDisplay.sys driver dated 6/21/2006. 6.2.9200.16384 (win8_rtm.120725-1247). Hardware - Mobo:MSi G41M-P33 Combo CPU:Intel CoreDuo 6600 Graphics:NVIDIA GeForce 9400GT *OS* - Windows 8 Pro 64-bit OEM The graphics adapter worked fine in Windows XP. The PC is a generic box, bought locally and its mobo failed recently, so I replaced it with the G41M. Microsoft wouldn't let me re-activate Windows XP with a different mobo, so I installed Win8, which appears to work except as described next. Win8 only partially recognizes the graphics adapter and won't allow NVIDIA latest driver installer to see that it's an NVIDIA card. As a result, OpenGL doesn't work, and this is needed by the software I most use. Other than that the graphics look OK. When I say 'partially recognizes', I mean that via the Control Panel, I can see that the adapter is described as NVIDIA, but the driver remains stuck at Microsoft Basic Display Adapter no matter what I try, including "Update driver..." in adapter properties. Display Screen Resolution Advanced Settings Adapter shows: Adapter Type: Microsoft Basic Display Adapter Chip Type: NVIDIA DAC Type: NVIDIA Corporation Bios Information: G27 Board - p381n17 Don't know what this means ... no mention of 9400GT Total Available Graphics Memory: 256 MB Dedicated Video Memory: 0 MB In fact the adapter has 512MB on-board video memory. System Video Memory: 0 MB Shared System Memory: 256 MB And Control Panel Device Manager Display adapters just shows Microsoft Basic Display Adapter. No other graphics adapter, and no unknown device or yellow question mark. What I have tried so far: 1. Cleared CMOS and reset. Updated BIOS and all mobo drivers as follows: 1st I used Driver Reviver to see if any driver updates were required. It found some but I didn't use that to get the drivers. Then I switched to MSi's own mobo driver utility Live Update 5. This also showed the board needed to update several so I used it to fetch the new drivers. After that it showed that everything was up to date and I checked with Driver Reviver again, which also reported no drivers now needed updating. Rebooted. Went to the NVIDIA site to get the latest graphics adapter driver. Their auto-detect "Option 2: Automatically find drivers for my NVIDIA products" said "The NVIDIA Smart Scan was unable to evaluate your system hardware. Please use Option 1 to manually find drivers for your NVIDIA products." So I downloaded 310.70-desktop-win8-win7-winvista-64bit-international-whql.exe, which lists 9400 GT under supported products, but when I run it, it says: "NVIDIA Installer cannot continue This graphics driver could not find compatible graphics hardware." Connected the display to the on-board Intel graphics (G41 Intel Express), removed the NVIDIA card and rebooted, changed to internal graphics in CMOS. Again it installs the MS Basic Display Adapter, and can't properly run my s/w that needs OpenGL. It runs on other machines with Intel Express graphics (WinXP and 7) Shut down and pulled out the power cord. Held start button to discharge all capacitors. Removed and re-inserted NVIDIA adapter in PCI-E slot and made sure properly seated. Connected the monitor to the card, screwed plug to socket. Reconnected power cord. Started and checked in BIOS that Primary Graphics Adapter was set to PCI-E. Started Windows. Uninstalled MS Basic Display Adapter in Device Manager. Screen blanks briefly, reappears. No Graphics adapter entry was then visible in Device Manager. Restarted PC. MS Basic Display Adapter Visible again in Device Manager. Clicked in Device Manager View Show hidden devices. No other graphics adapter appears, no unknown devices. Rebooted. Tried Scan for Hardware changes. None detected. Tried right-click on MS Basic Display Adapter Properties Driver Update Driver... Search automatically. It replied that it had determined driver was up to date. I checked that there were no graphic driver-related entries in Programs and Features that I could delete (none). Searched for any other drivers with nvidia in their name and deleted them, just keeping the 306.97 installer exe file. Did a Windows Update. Ran GPU-Z which shows (main items): Microsoft Basic Display Adapter GPU G72 BIOS 5.72.22.76.88 Device ID 10DE - 01D5 DDR2 Bus Width 32 Bit Memory size 64MB Driver Version nvlddmkm 6.2.9200.16384 (ForceWare 0.00) / Win8 64 NVIDIA SLI Unknown in the drop-down at the foot, "Microsoft Basic Display Adapter" is the only option If I swap hard disks in that machine to one with a Ubuntu 10.4 installation (originally installed on the same PC), lspci shows "VGA compatible controller as NVIDIA Corporation Device 01d5 (rev a1) (prog-if 00 [VGA controller])" and "kernel driver in use: nvidia" I'm out of ideas for new things to try and would be really grateful of suggestions. Thanks!

    Read the article

  • Wireless card not found on Ubuntu

    - by idealflip
    Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

    Read the article

  • Ubuntu on an XPS 14 Ultrabook with mSATA cache and 500GB HD - how to partition for dual boot?

    - by JDS
    I am getting an XPS 14 ( http://www.dell.com/us/p/xps-14-l421x/pd ) and I want to dual-boot Windows and Ubuntu. This thing has a 500GB standard HD and a 32GB mSATA that can be used as cache. Does anyone know how this thing is partitioned? Is the OS installed on the mSATA drive and data is on the big HD? Is there a BIOS controller or maybe even a Windows driver that makes the mSATA drive and 500GB HD appear contiguous? I get the impression that something makes the mSATA be used invisibly as cache, but I can't find any technical documentation how that works. My primary concern here is wrt dual-booting Ubuntu. I want to know if I need to partition the mSATA separately, or the big HD, or just partition the "magic" contiguous disk space that appears available to the OS.

    Read the article

  • ubuntu12.04 hangs at checking battery state

    - by crystalbass17
    My 12.04 system hangs at "Checking battery state". At this stage, no commands work eg: ctrl+alt+f1, alt+f5. I ran recovery mode, I ran the command sudo mount -o remount, rw sudo dpkg-reconfigure gdm and gdm was the only one installed so I didn't get a GUI screen. I have an integrated graphics card "Intel Corporation Mobile 4 chipset Integrated Graphics Controller (rev 07)". So I cannot install nvidia drivers as everyone else suggests. I have gone through several similar questions but everyone suggests reconfiguring gdm or reinstalling graphic drivers. I did sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get upgrade to get the latest x-swat drivers. The system still hung at the same line. The other option is to reinstall ubuntu, which is out of the question, since we have a very specific install for our project where the settings are very hard to duplicate. Suggestions/Comments welcome.

    Read the article

  • Why my AD domain doesn't work on my laptop

    - by Frederick Marcoux
    I have installed Windows Server 2008 R2 on a virtual machine with a bridged network card and installed Active Directory. I configured it and when I try to connect my laptop to the domain name, in this case, creationsmicroweb.ca (doesn't exist, don't try, for local only), I can't get connected. My laptop just doesn't see it. I don't know why! There's a resume of my config: Domain Name: creationsmicroweb.ca Forest: new, principal domain controller IP: Fixed (192.168.1.100) DNS Name: none (just for local, I ignored them) NETBIOS name: MICROWEB If someone as found why, please help me! This is for my business that I'm starting and I can't find why it doesn't work!

    Read the article

  • Multiple test Active Directory envirovments hand in hand with production domain controllers

    - by MadBoy
    What's the best approach of having multiple test environments next to production one? We have multiple programming teams that build solutions that use Active Directory very often. We have tried different approaches, starting with their own domain controllers (in same subnet), or additional OU's in our production AD that the team gets control over and can create/delete accounts within that one OU. We thought of possible 4 solutions: Setting up separate OU's in ou production env. Creating subdomains for our contoso.com domain like test.contoso.com, something.contoso.com and delegating control to the teams (would we need additional DC's or the two that we have already would be enough to hold this? Setting up additional test domain controler that has a trust to our main domain and all teams can use the test domain controler as they please. Setting up single domain controller for every team/project. We're taking in consideration amount of resources needed, security (for example having multiple domain controlers with multiple passwords may lead users to use simpler passwords) and overall best practices for this scenario.

    Read the article

  • ASUS K55VM Laptop unexpectedly shuts down

    - by Abhishek Sha
    I've read quite a few questions on SuperUser of people having laptop shutdown problems but mine is different. My laptop specs: Intel Core i7 3610QM (IvyBridge) NVIDIA GT630M 2GB and Intel GMA4000 8GB RAM Windows 7 64 Bit My laptop occasionally shuts down when playing FarCry 3. It's around 5 months old. I've played games like Crysis and it never shuts down unexpectedly. Since I experienced this shut down recently, I decided for GPU-Z to log the temperatures. The final log value at the time of shutdown were thus: GPU Core Clock [MHz] - 797.3 GPU Memory Clock [MHz] - 896.8 GPU Temperature [°C] - 89.0 GPU Load [%] - 99 Memory Controller Load [%] - 36 Video Engine Load [%] - 0 Memory Usage (Dedicated) [MB] - 535 Memory Usage (Dynamic) [MB] - 53 VDDC [V] - 1.0620 My drivers are up-to-date and I didn't encounter any BSODs at the time of shut down. It simply turns off.

    Read the article

facebook twitter digg google delicious technorati stumbleupon myspace wordpress linkedin gmail igoogle windows live tumblr viadeo yahoo buzz yahoo mail yahoo bookmarks favorites email print

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >