Search Results

Search found 24865 results on 995 pages for 'default route'.

Page 318/995 | < Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >

• How do I setup routing for 2 companies with different Internet connections on the same LAN?

  - by Clint Miller

  Here's the setup: 2 companies (A & B) share office space and a LAN. A 2nd ISP is brought in and company A wants it's own Internet connection (ISP A) and company B wants it's own Internet connection (ISP B). VLANs are deployed internally to separate the 2 company's networks (company A: VLAN 1, company B: VLAN 2, shared VOIP: VLAN 3). With separate VLANs it's simple enough to use separate DHCP servers (or separate scopes on the same server) to assign the default gateway to each company's gateway for their Internet connection. Static routes can be created on each gateway to point traffic destined for the other company's VLAN or the voice VLAN so that all nodes are reachable as expected. However, I think this is a form of asymmetrical routing, right? (The path from node A1 to node B1 is not the same as the path back from node B1 to node A1). Can I setup policy-based routing to correct this? In that case, can I assign the same default gateway to every device on all VLANs and create a routing policy on a L3 switch to look at the source address and forward traffic to the appropriate next hop? In that case, I want the routing logic to go like this: If the destination address is known, forward the traffic (traffic destined for a different VLAN). If the destination address is unknown, forward the traffic to ISP A's gateway if the source address is on VLAN A; or forward the traffic to ISP B's gateway if the source address is VLAN B. Am I thinking about this problem in the correct way? Is there another way to solve this problem that I am overlooking?

  Read the article

• Is there any viable alternative to using a linux/unix/BSD firewall/router/vpn?

  - by ObligatoryMoniker

  I am trying to purchase something to replace our Vyatta router that is running in a virtual machine on Hyper V (having the whole network go down when the host has to reboot is not convenient and I am getting the sense that this configuration may not be stable). Most posts on this topic suggest using Linux/OpenBSD/FreeBSD/etc with some recommendations to use appliances from vendors for specific purposes like firewall and VPN. We are a windows shop and it has been a stretch for us to make use of Vyatta but since it was free and straightforward to use we decided to use it. Now we need something that is easier for our team to (re)deploy and manage. I would rather purchase something windows based or an appliance that can do all of the following things: DHCP server (reservations, specified gateway, dns, etc) Static Routes that route traffic across three interfaces Easily Reproducible (Powershell script, Puppet, Chef, etc) Intuitive interface (Decent web interface would be fine but I don't want them to have to go to CLI) Does any one have any recommendations on what I should be looking at that might meet our needs?

  Read the article

• Mounting a VirtualBox shared folder on boot with fstab in OpenSuse 11.3

  - by ccook

  I have followed the steps found here, however, the share is not mounted on boot. The share will mount if i run 'mount -a' after booting. Why would the share not mount on boot? 1 - Set up a Virtual Machine and install OpenSUSE 11.2 2 - Create a shared folder on host (HostFolder) 3 - Setup the shared folder in Virtualbox Via the Virtual Machine details or via Devices Shared Folders... 4 - Install dependencies for running the Virtualbox installer You need to install the right development kernelpackage for your machinetype (use 'zypper search -i kernel' to see what's installed) sudo zypper install make gcc kernel-source kernel-hosttype/default-devel 5 - Run the Virtual Machine and go to Devices Guest Additions This mounts an iso image in your OpenSUSE guest. 6 - Open a root terminal and run cd /usr/src/linux make oldconfig && make prepare && make scripts && make dep cp ../linux-obj/$HOSTTYPE/default/Module.symvers . make prepare A commenter on previously mentioned thread says this step is unnecessary but it doesn't work without on my system. I suggest trying step 7 first and returning to step 6 if that fails. * 7 - Run ./VirtualboxLinux yourhosttype .run from the mounted iso image. 8 - Create shared folder in OpenSUSE (GuestFolder) 9 - Test with sudo mount -t vboxsf HostFolder /home/user/GuestFolder It works? Great! Let's set up the system so it automounts for your regular useraccount instead of root-only access. 10 - Add this line to /etc/fstab HostFolder /home/user/GuestFolder vboxsf defaults,uid=1000,gid=1000 0 0 11 - It works for me but if it still doesn't automount after a reboot; sudo mount -a

  Read the article

• How can I restore Outlook 2007 from a PST file without having to import everything?

  - by schnapple

  I recently upgraded to Windows 7 and went the "format from scratch" route. I backed up my C:\ drive to the free space on my D:\ drive. So now I have Outlook 2007 reinstalled and I have my .pst files and so forth from the previous installation. If memory serves the answer on getting all those emails back into Outlook again is "create a new .pst file for the account and then reimport everything". What I'd like to do is be able to just put the .pst file where it's supposed to go and then have Outlook 2007 just "remember" everything. But I'm pretty sure this doesn't work. Is there a way to restore Outlook from a pst file without having to re-import everything?

  Read the article

• Disappearing Arial on 2 Macs

  - by drewk

  I noticed that Safari started rendering common web pages in a funny manner on two different Macs that I have. One is a Macbook Pro and the other a Mac Pro desktop. Yahoo and Google would appear all excessively bold or all italic and not at all look right or acceptable. The computers are all running OS X 10.6.3 "Snow Leopard" Turns out that "Arial.TTF" and "Arial Bold.ttf" got deleted somehow on these two computers. I restored Arial through Font Book and got my web mojo back. So questions: 1) Anyone seen "arial" strangely randomly disappear? The only thing in common is these are the only two computers out of eight on site that recently got Adobe CS 5 installed. Has anyone had CS 5 delete arial? 2) When I restored arial with font book, it goes into User fonts rather than the All fonts. Can I use Font Book to restore a font in /System/Library/Fonts or do I need to do that manually? 3) I located THIS article on the web regarding OS X fonts. Essentially, Snow Leopard did away with the older .dfont format and replaced with open True Type. There is a minimum font list, but Arial is not among them. Arial is installed by MS Office. 4) Why are web sites affected by Arial being missing anyway? If I look at the HTML source for Yahoo for example, "arial" is specified by name only in an ad. Yahoo itself does not specify a font name. In my Safari preferences, I have Times and Courier specified as the default font which is the default for Safari when installed. How does a missing Arial screw things up anyway? Thanks in advance.

  Read the article

• nginx: how do I add new site/server_name in nginx?

  - by Neo

  I'm just starting to explore Nginx on my Ubuntu 10.04. I installed Nginx and I'm able to get the "Welcome to Nginx" page on localhost. However I'm not able to add a new server_name, even when I make the changes in site-available/default file. Tried reloading/restarting Nginx, but nothing works. One interesting observation. "http://mycomputername" in browser works. So somehow there is a command like 'server_name $hostname' somewhere over-riding my rule. File: sites-available/mine.enpass server { listen 80; server_name mine.enpass ; access_log /var/log/nginx/localhost.access.log; location / { root /var/www/nginx-default; index index.html index.htm; } } File: nginx.confg user www-data; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_comp_level 2; gzip_proxied any; gzip_types text/plain text/css application/x-javascript text/xml application/xml application/xml+rss text/javascript; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; }

  Read the article

• Traffic shaping on Linux with HTB: weird results

  - by DADGAD

  I'm trying to have some simple bandwidth throttling set up on a Linux server and I'm running into what seems to be very weird stuff despite a seemingly trivial config. I want to shape traffic coming to a specific client IP (10.41.240.240) to a hard maximum of 75Kbit/s. Here's how I set up the shaping: # tc qdisc add dev eth1 root handle 1: htb default 1 r2q 1 # tc class add dev eth1 parent 1: classid 1:1 htb rate 75Kbit # tc class add dev eth1 parent 1:1 classid 1:10 htb rate 75kbit # tc filter add dev eth1 parent 1:0 protocol ip prio 1 u32 match ip dst 10.41.240.240 flowid 1:10 To test, I start a file download over HTTP from the said client machine and measure the resulting speed by looking at Kb/s in Firefox. Now, the behaviour is rather puzzling: the DL starts at about 10Kbyte/s and proceeds to pick up speed until it stabilizes at about 75Kbytes/s (Kilobytes, not Kilobits as configured!). Then, If I start several parallel downloads of that very same file, each download stabilizes at about 45Kbytes/s; the combined speed of those downloads thus greatly exceeds the configured maximum. Here's what I get when probing tc for debug info [root@kup-gw-02 /]# tc -s qdisc show dev eth1 qdisc htb 1: r2q 1 default 1 direct_packets_stat 1 Sent 17475717 bytes 1334 pkt (dropped 0, overlimits 2782 requeues 0) rate 0bit 0pps backlog 0b 12p requeues 0 [root@kup-gw-02 /]# tc -s class show dev eth1 class htb 1:1 root rate 75000bit ceil 75000bit burst 1608b cburst 1608b Sent 14369397 bytes 1124 pkt (dropped 0, overlimits 0 requeues 0) rate 577896bit 5pps backlog 0b 0p requeues 0 lended: 1 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 class htb 1:10 parent 1:1 prio 0 **rate 75000bit ceil 75000bit** burst 1608b cburst 1608b Sent 14529077 bytes 1134 pkt (dropped 0, overlimits 0 requeues 0) **rate 589888bit** 5pps backlog 0b 11p requeues 0 lended: 1123 borrowed: 0 giants: 1938 tokens: -205561 ctokens: -205561 What I can't for the life of me understand is this: how come I get a "rate 589888bit 5pps" with a config of "rate 75000bit ceil 75000bit"? Why does the effective rate get so much higher than the configured rate? What am I doing wrong? Why is it behaving the way it is? Please help, I'm stumped. Thanks guys.

  Read the article

• What's the best way to run Drupal and Django sites behind the same Varnish server?

  - by Alexis Bellido

  I have a high traffic website running with Drupal and Apache, five web servers behind a Varnish server load balancing. Let's say this site is example.com. I'm using five backends and a director like this in my default.vcl: director balancer round-robin { { .backend = web1; } { .backend = web2; } { .backend = web3; } { .backend = web4; } { .backend = web5; } } Now I'm working on a new Django project that will be a new section of this site running on example.com/new-section. After checking the documentation I found I can do something like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.backend = newbackend; } else { set req.backend = default; } } That is, using a different backend for a subdirectory /new-section under the same domain. My question is, how do I make something like this work with my director and load balancing setup? I'm probably going to run two or more web servers (backends) with my new Django project, each one with a mix of Gunicorn, Nginx, and a few Python packages, and would like to put all of those in their own Varnish director to load balance. Is it possible to do use the above approach to decide which director to use?, like this: sub vcl_recv { if (req.url ~ "^/new-section/") { set req.director = newdirector; } else { set req.director = balancer; } } All suggestions welcome. Thanks!

  Read the article

• CentOS Latency High Troubleshooting

  - by Sarah Weinberger

  I have two CentOS servers connected via a 10 Gb fiber optic cable with a network emulator connected between them. All three units sit on a desk in the lab. There is also a regular 1 Gbit Ethernet cable connected to each of the machines, which provide internet connectivity. When I set the latency to something roughly below 30 ms, all is fine. When the latency gets to 70ms and above, and definitely 130ms, the network layer suspends. For instance, if I set the latency (delay) to 70ms, then launching TeamViewer (or any other application that uses network connectivity) never happens or does not work. There is no timeout message, simply no response. I have to lower to latency back down to zero to see any response and have the box start working. What is the problem and how would I go about fixing it? It seems to me some sort of setting in Linux causes one of the CentOS networking drivers to sit in an infinite loop or something. eth0 is the connection to the internet, all settings are default eth2 is the 10 Gbit fiber optic connection to the other computer with the MTU set to 9600 with all other parameters at default values.

  Read the article

• Ubuntu 10.04 RGBA(Transparent theme) bug

  - by Nrew

  I tried to follow this tutorial frome ghacks.net. But I end up with a bug. Everytime I try to change the desktop background or the theme. It opens up lots of folders. And then close it back again. So I cannot do anything when I try to change the background or the theme to the default. Here is the tutorial And I can't even shutdown my machine now, please help. EDIT I tried executing these commands in the terminal sudo add-apt-repository ppa:erik-b-andersen/rgba-gtk sudo apt-get update && sudo apt-get upgrade sudo apt-get install gnome-color-chooser gtk2-module-rgba sudo apt-get install murrine-themes And it installed gnome color changer. It works, and the windows became transparent, but I can't change to the default theme and I can't put a background Here's the screenshot, when I try to change something in the preferences: Its just okay if I can't change the theme, but it won't let me change the background either. Or maybe the background is changed but its transparent just like the other windows. You can see that in the taskbar(or whatever its called in Ubuntu). Its full. What can I do to atleast make the background visible.

  Read the article

• iperf max udp multicast performance peaking at 10Mbit/s?

  - by Tom Frey

  I'm trying to test UDP multicast throughput via iperf but it seems like it's not sending more than 10Mbit/s from my dev machine: C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [156] local 192.168.1.99 port 49693 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [156] 0.0- 1.0 sec 1.22 MBytes 10.2 Mbits/sec [156] 1.0- 2.0 sec 1.14 MBytes 9.57 Mbits/sec [156] 2.0- 3.0 sec 1.14 MBytes 9.55 Mbits/sec [156] 3.0- 4.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 4.0- 5.0 sec 1.14 MBytes 9.56 Mbits/sec [156] 5.0- 6.0 sec 1.15 MBytes 9.62 Mbits/sec [156] 6.0- 7.0 sec 1.14 MBytes 9.53 Mbits/sec When I run it on another server, I'm getting ~80Mbit/s which is quite a bit better but still not anywhere near the 1Gbps limits that I should be getting? C:\> iperf -c 224.0.166.111 -u -T 1 -t 100 -i 1 -b 1000000000 ------------------------------------------------------------ Client connecting to 224.0.166.111, UDP port 5001 Sending 1470 byte datagrams Setting multicast TTL to 1 UDP buffer size: 8.00 KByte (default) ------------------------------------------------------------ [180] local 10.0.101.102 port 51559 connected with 224.0.166.111 port 5001 [ ID] Interval Transfer Bandwidth [180] 0.0- 1.0 sec 8.60 MBytes 72.1 Mbits/sec [180] 1.0- 2.0 sec 8.73 MBytes 73.2 Mbits/sec [180] 2.0- 3.0 sec 8.76 MBytes 73.5 Mbits/sec [180] 3.0- 4.0 sec 9.58 MBytes 80.3 Mbits/sec [180] 4.0- 5.0 sec 9.95 MBytes 83.4 Mbits/sec [180] 5.0- 6.0 sec 10.5 MBytes 87.9 Mbits/sec [180] 6.0- 7.0 sec 10.9 MBytes 91.1 Mbits/sec [180] 7.0- 8.0 sec 11.2 MBytes 94.0 Mbits/sec Anybody has any idea why this is not achieving close to link limits (1Gbps)? Thanks, Tom

  Read the article

• VPN, routing, specified application

  - by Adrian

  Details: eth0 = current internet port pptp1 = VPN connection, if I connect to my provider, he give me an IP address, which is accessible from the internet. This is what I need. I want to connect through this IP back to my PC. I want to keep my primary internet connection (eth0) on my PC for all traffic, but route traffic to VPN for specified application/or port, to access application/port from the IP, which I given from the pptp provider. Huhh? Difficult but, it is possible? If yes, how? Incoming port will be always: 33340 Outgoing port can be change, but usually it is 33330

  Read the article

• Plesk: Spamassassin ignores emails to redirected accounts

  - by Mat

  When I set up email redirects within Plesk 9.5, Spamassassin ignores all emails sent to the redirected address and only scans emails that are sent directly to the address which has a mailbox. Steps to reproduce Set up two mail accounts: [email protected] as a proper email account with a mailbox and [email protected] with all emails redirected to [email protected]. (It doesn't make a difference, if [email protected] has a mailbox enabled or not.) [email protected] -> [email protected] Set up the spam filter on both accounts. I set mine to delete spam right away, but you can just keep the default ("mark as spam"). Now, when you send an emails to [email protected], it will have Spamassassins tags in the email header, but when you send emails to [email protected], they will end up in the same mailbox but will have no spamassassin tags in the emails header and they will not be scanned. Other notes I am using Plesk 9.5.4 on Ubuntu 8.04 LTS with the default Qmail. I've observed this bug since Plesk 8, but I can't stand it any more and would appreciate any hack or fix.

  Read the article

• HOW TO save Contacts from iPhone to Computer?

  - by goodm

  Step 1: Download [b]Tansee iPhone Transfer Contact[/b] free trial version [url="http://softseeking.com/prodail.aspx?proid=47"]here[/url],then install the software (skip if done yet). u can download at:[url="http://www.softseeking.com/prodail.aspx?proid=47"]http://www.softseeking.com/prodail.aspx?proid=47[/url] Step 2: Connect iPhone to your computer. Step 3: Run Tansee iPhone Transfer Contact , your contacts on iPhone memory will display as shown in your iPhone screen automatically as fig 1. Click on single name, all his or her information will display as fig 2 shown. Step 4-a: In fig 1 situation, you can click button "Copy" to copy all contacts from your iPhone to your computer , then select options: 1: Choose File Type: backup to TXT file, ANTC file or CSV file; 2: Choose File Path: You can change the backup path if you do not use default path. 3: Advanced Option: if you choose ANTC format in step 1, you can add a password to protect the file. Note: We do not know the password, so please do remember it. Click OK Button to finish the Copy. See fig 3. Note: You can only copy the first 5 contacts with trail version.[/SIZE] [/SIZE] [size=3][size=3]Step 4-b: In fig 2 situation, click button "Copy Contact From who" to copy contact of a single person, select options: 1: Choose File Type: Backup contacts to TXT file, and CSV file in single contact transfer; 2: Choose File Path: You can change the backup path if you do not use default path; 3: Advanced Option: Disabled in single contact transfer. Click OK Button to finish the Copy. See fig 4. Note: You can only copy the first 5 contacts in trail version.[/size] [/size]

  Read the article

• How to cache authentication in Linux using PAM/Kerberos authentication (for CVS)?

  - by Calonthar

  We have several Linux servers that authenticate Linux user passwords on our Windows Active Directory Server using PAM and Kerberos 5. The Linux distro we use is CentOS 6. On one system, we have several Version Control Systems like CVS and Subversion, both of which authenticate users throug PAM, such that users can use their normal Unix resp. Windows AD accounts. Since we started using Kerberos for password authentication, we experienced that CVS on a client machine is often much slower in establishing a connection. CVS authenticates the user on every request (eg. cvs diff, log, update...). Is is possible to cache the credentials that kerberos uses, sucht that is does not need to ask the Windows AD server every time a user executes a cvs action? Our PAM config /etc/pam.d/system-auth looks like the following: auth required pam_env.so auth sufficient pam_unix.so nullok try_first_pass auth requisite pam_succeed_if.so uid >= 500 quiet auth sufficient pam_krb5.so use_first_pass auth required pam_deny.so account required pam_unix.so broken_shadow account sufficient pam_succeed_if.so uid < 500 quiet account [default=bad success=ok user_unknown=ignore] pam_krb5.so account required pam_permit.so password requisite pam_cracklib.so try_first_pass retry=3 password sufficient pam_unix.so md5 shadow nullok try_first_pass use_authtok password sufficient pam_krb5.so use_authtok password required pam_deny.so session optional pam_keyinit.so revoke session required pam_limits.so session [success=1 default=ignore] pam_succeed_if.so service in crond quiet use_uid session required pam_unix.so session optional pam_krb5.so

  Read the article

• How to Load Balance 2 Internet Connections on a Windows 7 machine?

  - by Jimmy Chandra

  It's sort of related to this particular question, but that one is on Mac. I am looking for similar solution on Windows 7. I have 2 network connections: (Connection A) Wireless terminal connecting to ISP A (3G / EVDO internet provider) (Connection B) Broadband wired connection connecting to ISP B (Cable internet provider) Both has access to the internet. When I try connecting to a website and checking the networking tab on my Task Manager, I only see the network traffic being routed to only Connection A. Is there a way to make the computer to utilize both network (in a sense using all the bandwidth available from both the Cable ISP and the 3G / EVDO ISP) at the same time? If so, what do I need to do to set this up ... on Windows 7? Here is a bit more info on my network connections (ipconfig /all): PPP adapter Wireless Terminal: IPv4: aa.bb.ccc.ddd(preferred) Subnet mask: 255.255.255.255 Default Gateway: 0.0.0.0 DNS: aa.ee.f.ggg aa.ee.f.hhh Primary Wins: jjj.ii.k.l Secondary Wins: jjj.ii.k.m Ethernet adapter LAN: IPv4: 192.168.1.100 (connected to a router by wired that itself connect to a cable modem) subnet mask: 255.255.255.0 Default gateway: 192.168.1.1 (the wireless router) DHCP: 192.168.1.1 (the wireless router) DNS: xxx.yy.zz.ww rr.sss.t.uuu For my own privacy, I don't believe the actual number matters, the patterns are representative of the ip numbering scheme...

  Read the article

• Unattended Kickstart Install

  - by Eric

  I've looked around quite a bit and have seen similar setup and questions, but none seem to work for me. I'm using the following command to create a custom ISO: /usr/bin/livecd-creator --config=/usr/share/livecd-tools/test.ks --fslabel=TestAppliance --cache=/var/cache/live This works great and it creates the ISO with all of the packages and configs I want on it. My issue is that I want the install to be unattended. However, every time I start the CD, it asks for all of the info such as keyboard, time zone, root password, etc. These are my basic settings I have in my kickstart script prior to the packages section. cdrom install autopart autostep xconfig --startxonboot rootpw testpassword lang en_US.UTF-8 keyboard us timezone --utc America/New_York auth --useshadow --enablemd5 selinux --disabled services --enabled=iptables,rsyslog,sshd,ntpd,NetworkManager,network --disabled=sendmail,cups,firstboot,ip6tables clearpart --all So after looking around, I was told that I need to modify my isolinux.cfg file to either do "ks=http://X.X.X.X/location/to/test.ks" or "ks=cdrom:/test.ks". I've tried both methods and it still forces me to go through the install process. When I tail the apache logs on the server, I see that the ISO never even tries to get the file. Below are the exact syntax I'm trying on my isolinux.cfg file. label http menu label HTTP kernel vmlinuz0 append initrd=initrd0.img ks=http://192.168.56.101/files/test.ks ksdevice=eth0 label localks menu label LocalKS kernel vmlinuz0 append initrd=initrd0.img ks=cdrom:/test.ks label install0 menu label Install kernel vmlinuz0 append initrd=initrd0.img root=live:CDLABEL=PerimeterAppliance rootfstype=auto ro liveimg liveinst noswap rd_NO_LUKS rd_NO_MD rd_NO_DM menu default EOF_boot_menu The first 2 give me a "dracut: fatal: no or empty root=" error until I give it a root= option and then it just skips the kickstart completely. The last one is my default option that works fine, but just requires a lot of user input. Any help would be greatly appreciated.

  Read the article

• how to connect public web server to internal LAN

  - by DefSol

  I have a VPS which is my public web server for all my clients. It's running server 2008 and I would like to have it connect via secure connection to my internal LAN. I would like this to be a route so access is bi-derectional. Have read about Server & Domain isolation, but am concerned this may prevent public views to the webs sites on the server. I currently have a PPTP tunnel, but I'm wanting better security (IPSec or SSL etc) and it's not given my bi derectional access. (In fact my backups aren't copying accross but this could be an acl issue) The goal is to provide easy/automated backups of data & sql db's to my internal LAN, as well as a means to provision new sites & db's from a workflow occuring internally. Internal lan is windows based with ISA 2006 at the perimeter. Thanks

  Read the article

• Windows 7 starter will not shutdown or logoff

  - by richzilla

  Hi all, Im having some problems with a friends netbook (a dell mini 10). It will not shutdown or logoff via the usual route. Whenever the shutdown/logoff button is clicked, it will briefly freeze (maybe for only a second) and then do nothing. Ive tried shutting down manually via the command line using shutdown /p but all to no avail, it just defaults back to flashing cursor in the command prompt. There doesnt seem to be any mention of a similar problem on google so i was wondering if anyone else had any ideas. Thanks oh and its runnning windows 7 starter.

  Read the article

• Wired and wireless conections: force Windows to connect to laptop through Ethernet?

  - by danielkza

  I have a desktop connected to the internet and to my home network through Wi-Fi, and a latptop connected to said desktop through an Ethernet cable. But Windows seems to only reach the laptop through Wi-Fi: I want to transfer files through the wired connection instead. Setting up Internet Connectin Sharing and disconnecting the laptop from Wi-Fi altogether doesn't seem like the most elegant solution to me. I also thought about going to the hosts file and setting up the IP address manually, but that would make the laptop completely unavailable if it's not wired, which happens quite often unfortunately. Is there any way for me to tell Windows to use the wired connection for a particular host if possible, and fallback to any other route it finds otherwise?

  Read the article

• Trying to test Domain Collapsing / Consoldiation validity for SEO purposes

  - by Roy Rico

  At work, we're trying to determine the effectiveness of domain collapsing for SEO purposes. Our current structure is to have multiple web apps served from different servers, such as PUBLIC URLS - directly accessed by users www1.somecompany.com/webapp1 www2.somecompany.com/webapp2 www3.somecompany.com/webapp3 I'm proposing to put an Apache proxy in front of these applications that will mask the different domains and route the requests to proper server PUBLIC URL--------routed/forwarded to-----PRIVATE URL www.somecompany.com/webapp1 <-----> www1.somecompany.com/webapp1 www.somecompany.com/webapp2 <-----> www2.somecompany.com/webapp2 www.somecompany.com/webapp3 <-----> www3.somecompany.com/webapp3 In terms of SEO/page rank value, does this help?

  Read the article

• squid configuration change to accept http request on LAN

  - by Ratan Kumar

  installed squid + dansguardian to block adult content on my linux (ubuntu 12.10) . everything worked fine. it has blocked as expected . now the problem is i am also running an apache server for my LAN . ( kind of website ) but when accessing it via 192.168.0.1 , it says squid has blocked the connection , this is the exact error The following error was encountered while trying to retrieve the URL: http: //192.168.0.16/ Connection to 192.168.0.16 failed. The system returned: (113) No route to host The remote host or network may be down. Please try the request again. Your cache administrator is webmaster. before configuring the squid it was working fine . what changes in the squid.conf i have to make . i tried acl Safe_ports 80 allow_all Safe_ports ( i want to know how i can configure it again to listen HTTP request from LAN )

  Read the article

• OpenBSD ftp-proxy behind NAT itself

  - by Manuel Faux

  Is it possible to change the PASV IP ftp-proxy of OpenBSD sends to clients, without changing the listen address of redirection control (-b <address>)? I have the following setup: FTP client --> 1:1 NAT router --> OpenBSD router --> FTP server The 1:1 NAT router has a NAT rule to forward everything to the OpenBSD router, the OpenBSD router runs the ftp-proxy -R <FTP server IP>. When the FTP client sends the PASV command, the proxy answers with the Entering Passive Mode (227) message with his own source IP on the interface to the 1:1 NAT router (obviously). Since the 1:1 NAT router is not protocol aware, it forwards this message and the client receives the message with the PASV IP of the OpenBSD router, which it does not have a route to. Is there a way, that I can tell ftp-proxy to send the Entering Passive Mode message with a different source IP?

  Read the article

• haproxy access list using path_dir having issues with firefox

  - by user11243

  I'm trying to route all requests containing a path directory of /socket.io/ to a separate port with HAProxy. Here is my config file: global maxconn 4096 # Total Max Connections. This is dependent on ulimit nbproc 2 defaults mode http frontend all 0.0.0.0:80 timeout client 86400000 default_backend web_servers acl is_stream path_dir socket.io use_backend stream_servers if is_stream backend web_servers balance roundrobin option forwardfor # This sets X-Forwarded-For timeout server 30000 timeout connect 4000 server web1 127.0.0.1:4000 weight 1 maxconn 1024 check backend stream_servers balance roundrobin option forwardfor # This sets X-Forwarded-For timeout queue 5000 timeout server 86400000 timeout connect 86400000 server stream1 127.0.0.1:5100 weight 1 maxconn 1024 check URL paths with a /socket.io/ get correctly directed to port 5100 in chrome and safari. However not for firefox. I'm running Haproxy locally on my mac for dev, not sure if it has anything to do with it. I'm using haproxy 1.4.8 and Firefox 3.6.15. I've tried clearing cache on firefox and it didn't help, so I'm thinking there's something wrong with the way HAProxy parses through the Firefox request headers.

  Read the article

• Ruby on Rails cannot find Initializer?

  - by Ryan M.

  Hello, I am trying to deploy an app to a fresh Ubuntu 10 installation using Passenger 2.2.15, Rails 2.3.5, Ruby 1.8.7, and Apache 2.2.14. However, even with a default rails app (sudo rails defaultapp), I am receiving the following error: "no such file to load -- initializer". I'm not sure which files you might need copies of in order to diagnose this problem, so I'll copy a few here and hope that it will help. Thanks for any help you can provide. -RM /etc/apache2/sites-available/default <VirtualHost *:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/appname/public <Directory /> Options FollowSymLinks AllowOverride None </Directory> <Directory /var/www/> Options Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all </Directory> ScriptAlias /cgi-bin/ /usr/lib/cgi-bin/ <Directory "/usr/lib/cgi-bin"> AllowOverride None Options +ExecCGI -MultiViews +SymLinksIfOwnerMatch Order allow,deny Allow from all </Directory> ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined Alias /doc/ "/usr/share/doc/" <Directory "/usr/share/doc/"> Options Indexes MultiViews FollowSymLinks AllowOverride None Order deny,allow Deny from all Allow from 127.0.0.0/255.0.0.0 ::1/128 </Directory> </VirtualHost> /etc/apache2/mods-available/passenger.conf <IfModule passenger_module> PassengerRoot /usr/lib/ruby/gems/1.8/gems/passenger-2.2.15 PassengerRuby /usr/bin/ruby1.8 </IfModule> /etc/apache2/mods-available/passenger.load LoadModule passenger_module /usr/lib/ruby/gems/1.8/gems/passenger-2.2.15/ext/apache2/mod_passenger.so

  Read the article

< Previous Page | 314 315 316 317 318 319 320 321 322 323 324 325  | Next Page >