Search Results

Search found 29554 results on 1183 pages for 'human computer interface'.

Page 320/1183 | < Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >

• Windows 7 - Wireless Signal Good - Internet Often Says Limited or No Activity

  - by Anthony Trilussa Pizzo

  Hi - I have a New Dell Studio XPS latop that I hooked up in early January of 2010. The Dell Studio XPS laptop is connected to my wireless router (Belkin Wireless N). The router was purchased in Februaru of 2010 because I thought my router was bad (A D-Link router). Comcast is my ISP. Everyday, at random times, the internet will have a good signal (according to the little Win 7 icon on the taskbar) but I will receive a message saying limited or no internet access and I cannot access the internet. I have the internet setup to automatically get an IP and I did the IPCONFIG release / renew but with no success. I even had a WiFi enabled Blackberry right next to my computer and whenever the computer loses an WiFi connection, so does the Blackberry. The router isnt't bad, because the old router did the same thing - giving me limited or no internet access while working sometimes. I also tried using two other laptops in same physical position as my Dell Studio XPS laptop and they have the same problem. I am going crazy trying to figure this out as I have called the Router Company (Belkin), my ISP (Comcast), and my computer maker (Dell). Can anyone offer some suggestions and I can try them as we work through this and maybe one of the suggestion will be right one. Thanks in advance for even reading my problem. I searched for a problem similar to mine on the internet, but I have not been able to keep a steady internet connection. (Side note - I used to have an IBM thinkpad laptop and D - Link router and for years that wireless connection worked FLAWLESSLY, with the same physical set up - the laptop in my bedroom, and the router in the basement.)

  Read the article

• Why is my cat5e cable not okay?

  - by torbengb

  My LAN cable seems to work (indicator LED lights up) but the computer can't find a connection. What's wrong? Setup: I had to run a network cable from a router in one room to a computer to another room, through a hole in the wall that was too small to pass the RJ-45 plug through. The plug was cut off and the cable passed through the wall. Then a new plug was crimped on using this detailed explanation. The connection didn't work because the (factory-made!) plug in the other end used a non-standard wire order. I crimped a new plug on again, using the exact same order of the factory-made plug. The LED indicator lights up on both ends, but the computer cannot find a connection. What can be wrong? How can I find out? I don't have a cable tester. By visually inspecting my new plug, I think it's good; the wire order matches the other end, and all wires are all the way inside the plug and reach the connector piece. I've used the cable before (with both factory-made ends) so i don't think that the cable itself has a defect.

  Read the article

• Partitioning External Hard Drive

  - by Srin

  Is there a way to partition a External Hard drive ? I have a WD 500GB external hard drive with USB interface

  Read the article

• Data Protection Manager System Protection Backups Failing

  - by TrueDuality

  I'm just starting to setup DPM 2010 in a test environment with a Domain Controller and a File Server. Everything seem to be working fairly well and I can get all of my backup jobs to succeed except for the "Computer\System Protection" backups. Both servers are running fully up to date 64 bit Windows Server 2008 R2 Enterprise with Service Pack 1. The error that is being provided is: DPM cannot create a backup because Windows Server Backup (WSB) on the protected computer encountered an error (WSB Event ID: 517, WSB Error Code: 0x8078001D). (ID 30229 Details: Internal error code: 0x809909FB) This Microsoft Knowledge Base article describes the issue perfectly and provides a hotfix. I downloaded the hotfix, moved it onto the affected server, attempt to run it and receive the following error: The update is not applicable to your computer. I've verified that I have indeed downloaded the 64 bit version. According to this thread the hotfix got rolled into Service Pack 1, yet I'm still experiencing the issue. Both machines do have the Windows Server Backup feature installed. Can anybody point me in the right direction? What am I missing?

  Read the article

• Routing based on source address in Windows Server 2008 R2

  - by rocku

  Hi, I'm implementing a direct routing load balanced solution using Windows Server 2008 R2 as back-end server. I've configured a loopback interface with the external IP address. This works, I am receiving packets with the external IP address and respond to them appropriately. However our infrastructure requires that traffic which is being load-balanced should go through a different gateway then any other traffic originating from the server, ie. updates etc. So basicly I need to route packets based on source address (external IP) to another gateway. The built-in Windows 'route' command allows routing based on destination address only. I've tried setting a default gateway on the loopback interface and mangled with weak/strong host send/receive parameters on the interfaces, however this didn't work. Is there any way around this, possibly using third party tools?

  Read the article

• Web based library management (FOSS) application

  - by pgb

  I'm looking for a FOSS web-based library management application. I want to manage the few books we have at our company, and I'm looking for applications that provide a simple web interface to: Add new books. Search for books. (Not Required) Place holds on books. My ideal would be something like Delicious Library, but web based and open source. I've looked at Koha (which I could not install), Emilda, which seems to be a dead project (last emails are from 2006 and I could not install it) and VuFind which looks awesome but doesn't provide (or I could not find) an interface to add new records to the library. Any suggestions?

  Read the article

• System hangs while rebooting on Debian...

  - by Usman

  Hi, I have Debian (Kernel 2.6.26-2-686) installed on two computers. On one of them it reboots quite finely but I am having following problem with rebooting Debian on my second computer. When i type reboot at the Linux prompt, following messages appear and system hangs up after saying "Restarting System": Broadcast message from root@myname (tty1) (Sun Jan 17 11:23:26 2010) The system is going down for reboot NOW! INIT: Switching to runlevel: 6 INIT: Sending processes the TERM signal Saving system clock Stopping enhanced syslog: rsyslogd. Asking all remaining processes to terminate...done. Deconfiguring network interfaces...done. Cleaning up ifupdown.... Deactivating swap...done. [ 31.789103] Restarting System. _ Normally when the sytem is busy "" sign blinks but "" at the last line above does not blink which shows, the system hanged up. I tried all keys but the screen is still frozen at the same point. The difference that I noted between my two computers is that I don't have ACPI support in the BIOS of the system which is giving me this error whereas the BIOS of my first computer do have ACPI support on which Debain do not give this restart-hanging problem. I have also disabled running the acpid script by running update-rc.d -f acpid remove but the problem still persists on the second computer. Any ideas to solve or get around this problem?

  Read the article

• Is this a common/bug on this PPPoE setting for Cisco ASA 5505?

  - by DCAlliances

  We have to change the way the firewall setup due to we've changed the internet provider. The way we setup we have ADSL modem and we have to do a full bridge mode and the firewall configuration has to change from Static IP to Use PPPoE option on Outside interface with PPPoE username and password, CHAP authentication, WAN IP and WAN subnet mask. [See the attachment] It's been working ok with the use of PPPoE option however the issue is that if we un-plug the power cable of the firewall. This "Outside" interface turned to blank - NO WAN IP, PPPoE username and password. So basically, we have to retype this information again. Is this common or a bug? Any ideas? Thanks

  Read the article

• Is my HDD dead forever?

  - by Roberto

  Yesterday I turned on my computer and it couldn't boot. I found out the hd (320GB SATA Seagate Momentus 7200.3 for notebook) was broken and it couldn't be recognized by the BIOS. I have another of the same hard drive, so I exchanged the boards. I found out that there is a problem on its board since my good hard drive didn't work. But the broken hard drive doesn't work with the good board as well: it can be recognized but when I insert a Windows Instalation DVD it says the hard drive is 0GB. I put it in a case and use it in another computer via USB, and but it doesn't show up in the "My Computer". I used a software to recover files called "GetDataBack for NTFS", it recognized the hard drive but with the wrong size (2TB). I try to make it read the hard drive but it got an I/O error reading sector. It tries to read, the hard drive spins up. So, since I'm using a good board on it, the problem seems to be internal. Is there anything someone could do to recover the files from it?

  Read the article

• Custom authentication method for GDM

  - by FMC

  I am trying to find a way of authenticating users on public computers through GDM, but I have a few things to be taken in account. The users do not have a login/password, they only thing they are given is a string. This string is unique and will allow us to identify them. You can see this string as a login without a password. The users must be present in a remote database The users must have the rights to login on the computer they are on at that time. A remote database would check if a booking on the computer had been set for that time by that user. Or if no booking had been made, allow to login. A default user id/home/gid has to be set to the user once logged in I have found ways to deal with most of those requirements, but not altogether. PAM looks nice to set up a custom way of checking if the user booked its computer. NSS MySQL looks nice to set up the environment. Would you know how to set up the environment by myself using a custom PAM module (using pam_python would be preferred)? Or any other method that could help me? Thanks in advance!

  Read the article

• Logitech webcam device only recognised by one software, without drivers

  - by Ben Franchuk

  A couple weeks ago I purchased a Logitech webcam at a garage sale; It did not come with any driver DVDs or anything like that. I plugged it in, turned on my computer, and continued work as usual. I did not at the time (and still have not) gotten any drivers for the device. Recently, though, I started up an audio software named as Cubase, only to find that it was picking up audio reads off of... something. I checked my sound card, and everything else plugged into my computer, but couldn't find where in the world this audio was being picked up from. There were no microphones listed in the device managers, and no "unknown devices" or whatever. Everything seemed as it always was. Running out of ideas, i blew an air-horn directly into the general area of the webcam, located directly in front of me. Sure enough, the audio peaked, indicating that the microphone was definitely in the webcam and that Cubase was somehow picking up this audio, even without drivers. The software lists the device as a "Universal USB Microphone". Adobe Audition, Soundbooth, and other audio applications cannot find the device either. Why is it that this one software (Cubase) can use this device without a driver, while every other piece of software on the computer can't? Not even the operating system can recognize it. Windows 7 Professional x64 bit

  Read the article

• Where are my Tomcat Logs?

  - by gav

  Hi All, I installed Tomcat6 on a Ubuntu 9.04 server using apt-get install tomcat6. I uploaded a WAR using the manager interface and tried to start the application but get a pretty generic error on the Web interface saying it couldn't be started. I am trying to find the logs to determine why my war won't start (I suspect low memory as i'm on a small VPS) but I don't know where they are. /var/lib/tomcat6/logs is empty. My Tomcat splash page reliably informs me of the following; Tomcat is installed with CATALINA_HOME in /usr/share/tomcat6 CATALINA_BASE in /var/lib/tomcat6, following the rules from /usr/share/doc/tomcat6-common/RUNNING.txt.gz. Thanks, Gav

  Read the article

• Open Garmin GPI files in Linux

  - by zero

  i have several files that are in the Garmin GPI format, from here, and want to access them in Linux. How can I do that? hello dear renan - well i found the solution - so thanks for your try to add some sense to the question. GEREAT work - and here we have the answer: i will Install gpsbabel to convert the stuff. The gpi.files are just xml files, You can - after converting with gpsbabel read them as a human being.

  Read the article

• Basic networking problem with Ubuntu 9.04 on Acer Extensa 5635Z laptop

  - by sapporo

  I just installed Ubuntu 9.04 on a brand new Acer Extensa 5635Z laptop, but ethernet networking does't work (wireless doesn't work either, but I'd be happy with ethernet for now). eth0 isn't listed in /etc/network/interfaces: $ cat /etc/network/interfaces auto lo iface lo inet loopback lshw does show the nic, but I can't make much sense out of the information: $ sudo lshw -class network -sanitize *-network DISABLED description: Wireless interface product: AR928X Wireless Network Adapter (PCI-Express) vendor: Atheros Communications Inc. physical id: 0 bus info: pci@0000:07:00.0 logical name: wmaster0 version: 01 serial: [REMOVED] width: 64 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list logical ethernet physical wireless configuration: broadcast=yes driver=ath9k latency=0 module=ath9k multicast=yes wireless=IEEE 802.11bgn *-network UNCLAIMED description: Ethernet controller product: Attansic Technology Corp. vendor: Attansic Technology Corp. physical id: 0 bus info: pci@0000:09:00.0 version: c0 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress vpd cap_list configuration: latency=0 *-network DISABLED description: Ethernet interface physical id: 1 logical name: pan0 serial: [REMOVED] capabilities: ethernet physical configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes Thanks for your help!

  Read the article

• Everyone can access my Windows 7 Homegroup file shares - Even Windows XP computers

  - by Adrian Grigore

  I have 3 computers in my network, two running Windows 7 and one running Windows XP. I've set up a homegroup on both Windows 7 computers. Also, all computers are in the same Workgroup. The problem is that one of the Windows 7 computers makes all shares accessible to the entire Workgroup instead of just sharing to the Homegroup as it should be. I created the file share in Windows 7 via right-click in the explorer, then click on "Share For" - "Homegroup (Read/Write)" (translated from German, so the actual wording may be different). Also, when I look at the file sharing properties of that folder, Windows Explorer informs me that Users must have a valid account and password for this Computer to access drive shares. Unfortunately this is not true. Being in the same Workgroup is enough to get access. Homegroup restrictions work as expected on my other Windows 7 computer. When trying to browse those shares from the XP computer, I get a dialog asking for a login and password. What might cause homegroup restrictions to fail and how can I fix this?

  Read the article

• LogMeIn Hamachi for Linux

  - by tlunter

  So far most of my work using LogMeIn Hamachi has been from either a Mac OS X or Windows system to Windows or a Linux Computer. Recently I purchased a mini computer and have been running Ubuntu Server on it, as my little server. I knew LogMeIn had a Linux client that is command line only, but I often do all my work via command line anyway, so that wasn't an issue. I added my user to the correct local file so that I could run the hamachi daemon without sudo, and was able to connect to LogMeIn's service. I decided to set up my Linux server as a git server as well, and set it up correctly. The thing is, the server is behind my schools firewall and I need to use hamachi to get around that. Since most of the time I was using either Mac or Windows, I never had an issue sshing onto any of my computers since LogMeIn is fully featured for these OSs. From Linux (Arch) though, it seems like the client cannot correctly route to the LogMeIn IPs. I know from Windows I can connect to the Linux computers, both of them. From Linux (Arch) though, I can't connect to my Mac, Windows, or Linux server. It keeps just dropping the connection. I was wondering if there was some configuration that I would need to make for this to work. I understand that it is most likely going to be a static configuration since I assume it has to do with the computer not understanding that 5.*.*.* actually refers to another IP:Port. Has anyone had any experience getting this to work?

  Read the article

• Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace

  - by Nick

  I have an laptop top hard drive I was trying to use to my new media computer. The case is small and can accommodate for 2 2.5" drives, no 3.5" drives. I had been using the hard drive as storage hard drive until now. When I go to install Windows on the hard drive first I'm prompted at the bios of: Hard Disk:S.M.A.R.T. Stas BAD, Back up and replace. And then again in the Windows Setup, informing me that the hard drive is bad. So I did a full format of the drive and tried again. Same error. So I took it out and hooked it back up to my other computer via an Sata usb adapter kit (maybe the cause?). The hard drive is recognized fine and when I scanned it for errors by going: right click -> properties -> tools -> error checking It returns that the hard drive is fine. I have tried 3 different SATA cables and multiple jumpers. When I plugged in my 1.5 tb 3.5" drive the computer that gives me the S.M.A.R.T. error on the 2.5" drive, recognizes it with no problems. Any ideas on why this is happening and how I can fix it?

  Read the article

• Routing traffic to another internal network

  - by Jason

  OK, so here is the scenario. I have 4 Locations connected with an MPLS. I have installed an ASA at the primary location which is 10.20.1.0. Traffic is fine internally and to the world, however... I can't route traffic over the MPLS to another network. It is being blocked by an implicit deny rule even though there is a rule to allow any to any less secure interface (it should be using the same interface in/out, right?). I have a static route for the network in and the ASA can ping it - Just not traffic on the internal network of the ASA. -Jason

  Read the article

• Linux Transparent Bridge for Network

  - by Blackninja543

  I am attempting to set up a semi-transparent bridge. I say semi because I want it to act as a transparent tap for all traffic moving through both sides of the bridge. What I also want is to have the "green zone" accessible to a web interface for the bridge that will display all results of the IDS and other network monitoring tools. My example would be as such: eth0 <--> bridge(br0) <--> eth1 The entire network would be on the same subset however anything coming from eth0 to eth1 would be accepted. The only time anything would be drop is if the eth0 attempted to access br0. If someone attempts to access the web interface on br0 through eth1 it will succeed. My biggest problem I feel is if I attempt to block anything from eth0 to br0 this will drop the bridge all together.

  Read the article

• Windows 2008 RRAS and PPPoE

  - by Massimo

  I'm trying to use Windows Server 2008's Routing and Remote Access Server to share an ADSL connection which uses PPPoE, but I'm having no luck. I can setup the connection as a broadband Internet connection in Windows, and it works. I can share it using Internet Connection sharing, and it works (but it's not what I need). I have installed and enabled the Routing and Remote Access Service and configured it for NAT with a demand-dial interface; I create the aforementioned interface using PPPoE with the exact same parameters used on the Windows connection; I connected it, and it seems to work: I can also see it gets its public IP address and DNS assigned correctly. But it just doesn't work. The server has no Internet connectivity at all, and PINGing anything on the Internet results in a cryptic "general error". Any help?

  Read the article

• Windows update stuck. Fixt it stuck. So is KB947821. What should I do?

  - by Jim Thio

  I installed a new computer. After I installed I update everything and let the computer runs for days. Then I don't know what my daughter do. The computer stop responding. Windows update no longer work. People said to run fix it. Fix it run and after that the problem still persist and it still doesn't work. The problem changes though. Before there is some error code. Now windows update simply "updating" never end. So I downloaded KB947821. It's been 3 hour and it's still installing. Looks like it hit firewall or something. i don't see windows update on firewall exception list. However, I've never heard that this is an issue. Firewall only protect against incoming transaction, not outgoing right? Or what am I missing. What should I do?

  Read the article

• OSX 10.6 Cisco IPSEC strange behavior

  - by tair

  I'm trying to connect to Cisco IPSEC VPN of my company over DSL Internet. I managed to successfully connect using Cisco VPN Client, now I'm trying to switch to OSX 10.6 native client, because of licensing issues. The problems is that the connection fails with a dialog box containing the message: The negotiation with the VPN server failed. Verify the server address and try reconnecting. I checked logs: Jun 29 13:10:39 racoon[4551]: Connecting. Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:10:39 racoon[4551]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:10:39 racoon[4551]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:10:39 racoon[4551]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:10:42 racoon[4551]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:10:42 racoon[4551]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:10:42 racoon[4551]: IKE Packet: receive success. (MODE-Config). Jun 29 13:10:42 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface setting (name: u92.168.54.147, subnet: 255.255.255.0, destination: 192.168.54.147). Jun 29 13:10:42 configd[19]: network configuration changed. Jun 29 13:10:42 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:42 named[62]: not listening on any interfaces Jun 29 13:10:58: --- last message repeated 1 time --- Jun 29 13:10:58 configd[19]: SCNCController: Disconnecting. (Connection tried to negotiate for, 16 seconds). Jun 29 13:10:58 racoon[4551]: IKE Packet: transmit success. (Information message). Jun 29 13:10:58 racoon[4551]: IKEv1 Information-Notice: transmit success. (Delete ISAKMP-SA). Jun 29 13:10:58 racoon[4551]: Disconnecting. (Connection tried to negotiate for, 19.113382 seconds). Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 vmnet-bridge[111]: Dynamic store changed Jun 29 13:10:58 named[62]: not listening on any interfaces Jun 29 13:10:58 configd[19]: network configuration changed. Then I opened Terminal, started pinging a server behind VPN, and tried to connect again. Now connection is OK! Logs this time: Jun 29 13:46:53 racoon[8136]: Connecting. Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 1). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 AUTH: success. (Initiator, Aggressive-Mode Message 2). Jun 29 13:46:53 racoon[8136]: IKE Packet: receive success. (Initiator, Aggressive-Mode message 2). Jun 29 13:46:53 racoon[8136]: IKEv1 Phase1 Initiator: success. (Initiator, Aggressive-Mode). Jun 29 13:46:53 racoon[8136]: IKE Packet: transmit success. (Initiator, Aggressive-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 XAUTH: success. (XAUTH Status is OK). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Mode-Config message). Jun 29 13:46:56 racoon[8136]: IKEv1 Config: retransmited. (Mode-Config retransmit). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (MODE-Config). Jun 29 13:46:56 configd[19]: event_callback: Address added. previous interface setting (name: en1, address: 192.168.1.107), current interface settinaddress: 192.168.54.149, subnet: 255.255.255.0, destination: 192.168.54.149). Jun 29 13:46:56 vmnet-bridge[111]: Dynamic store changed Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 configd[19]: network configuration changed. Jun 29 13:46:56 named[62]: not listening on any interfaces Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 1). Jun 29 13:46:56 racoon[8136]: IKE Packet: receive success. (Initiator, Quick-Mode message 2). Jun 29 13:46:56 racoon[8136]: IKE Packet: transmit success. (Initiator, Quick-Mode message 3). Jun 29 13:46:56 racoon[8136]: IKEv1 Phase2 Initiator: success. (Initiator, Quick-Mode). Jun 29 13:46:56 racoon[8136]: Connected. Jun 29 13:46:56 configd[19]: SCNCController: Connected. I tested it several times and it consistently behaves the same. What is the magic?

  Read the article

• How to get Windows 7 to automatically connect to an ad-hoc network?

  - by George Edison

  I have two machines - one is running Ubuntu 12.04 64-bit and the other is running Windows 7 Starter Edition (32-bit). The Ubuntu machine is connected to the Internet via the eth0 interface. That machine also has a wireless network interface (wlan0) that is currently functioning as an ad-hoc network. I can connect to the ad-hoc network just fine with the Windows machine but each time I wish to do so, I must manually initiate the connection and enter the password. Is there some way to instruct Windows to automatically connect to this network (an option I have for standard wireless networks but not ad-hoc networks)?

  Read the article

• Upgrading openSUSE 11.1 with Plesk Panel 9.3 to PHP 5.3

  - by Jonathan

  I'm running a VPS with openSUSE 11.1 (i586). On the VPS is Parallels Plesk Panel 9.3.0 installed. The current PHP-version is PHP 5.2.11. I want to upgrade PHP to PHP 5.3, but I can't find good instructions on how to do this. If I check for updates in Zypper, it says this is the latest release. In the Plesk Updates isn't an update either, both via the webbased interface and the command line interface. On Software.openSUSE.org I can find packages for PHP 5.3.1 in both the server:php/server_apache_openSUSE_11.1-repo and the server:php/openSUSE_11.1-repo (can't post the link because I'm a newbie here). But if I add one of those to Zypper, I still don't see an update. Is there here somebody who knows how to do this? And is it completely safe to update that way? I don't want to end up with a broken VPS... Thanks! Jonathan

  Read the article

• Flash alternative for iBook Mac?

  - by Hunter Dolan

  I have a old Apple iBook G4 that I decided to hook up to my main TV. I like the setup because I can surf the internet on my TV now. The only thing that I can't seem to do is watch Flash videos. Apparently Flash Player 10 doesn't play nice with the iBook's graphics card's GPU, leaving all the graphics processing to the CPU which is a disaster. Others suggested downgrading to Flash Player 9, I did that, and youtube worked fine, but Hulu (The main reason I wanted to hook it up to the TV in the first place) did not. Anyone know of a Flash alternative or a Flash 10 fix for the iBook? Or even a Hulu client that doesn't require Flash. Here are my iBook's Specs Model Name: iBook G4 <br> Model Identifier: PowerBook6,5 <br> Processor Name: PowerPC G4 (1.2) <br> Processor Speed: 1.2 GHz <br> Number Of CPUs: 1 <br> L2 Cache (per CPU): 512 KB <br> Memory: 512 MB <br> Bus Speed: 133 MHz <br> Boot ROM Version: 4.8.7f1 <br> Mac OS X Version: 10.5.8 <br> PS: Don't tell me that I need to buy a new computer. I know that I would have better results with a new computer but I don't want to buy a new computer just for Hulu.

  Read the article

< Previous Page | 316 317 318 319 320 321 322 323 324 325 326 327  | Next Page >