Search Results

Search found 12952 results on 519 pages for 'model'.

Page 321/519 | < Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >

• Asus z53 laptop overheating problem

  - by Tiberiu Hajas

  hi all, wondering if anyone encountered overheating of asus laptop ? especially the z53 model ? usually the right side of the laptop and vent in the upper corner is blowing hot air when under even minimal load, the CPU temperature can easily get to 65-70C and GPU is even above 80C. I'm using NHC (notebook health control) to set to a higher conservatory power consumption but that helps only a bit, anyone opened up the case ? wondering is require a dust clean ...etc ? I still have some warranty on it. thanks

  Read the article

• small light laptop with docking station that has a PCI(e) slot

  - by laramichaels

  Hi everyone, I am looking for a new laptop/netbook and I have two simple requirements: must be small (10-12in screen) and light (<=3-3.5pounds); must work with a dock into which I can put a PCI or PCI Express card. Basically, I have no performance requirements. Discontinued or low-end are fine. All I want is something easy to carry that when at work I can use a PCI/PCI Express card with to do multi-head. Eg, if an Acer Aspire 1410 fitted the second requirement I would by one in a blink. The only solution with which I am acquainted are Thinkpads that can go into the Thinkpad Advanced Dock. Do other laptop (or netbook brands) also offer the possibility of using Although this is not a "requirement" per se, I would rather hear about options that would not involve buying the latest-greatest-+$2k model... : ) Thank you for any advice! ~lara

  Read the article

• unknown monitor in lenova laptop

  - by kumar

  I have set of two lenova laptops in which Fedora core 13 is installed. In one machine, the monitor is detected properly such that It is possible to connect another monitor. But In another laptop, monitor is shown as unknown monitor. I tried to fix it by reinstalling xorg-x11-drv-intel.i686. But the problem remains same(unknown monitor). it is not possible to connect another monitor with this setting. Laptop model: G460. Graphics card: Intel Graphics Media accelerator HD. Thanks!

  Read the article

• Why does iChat Server keep connecting to proxy.eu.jabber.org?

  - by Tom Hamming

  I have OS X Server 10.6.5 running on a new Mac Mini (server model), serving several functions among which is iChat Server (iChat and Pidgin on Windows as clients). In the iChat log in Server Admin, I kept seeing entries about connecting to proxy.eu.jabber.org. It's for our office network and I wasn't excited about external access to it, so I disabled server-to-server XMPP federation and now the connections just time out. But why is it doing that in the first place? Sample log entry: (datetime) (servername)jabberd/resolver[portnum]: [xmpp-server._tcp.proxy.eu.jabber.org resolved to 208.68.163.220:5269 (300 seconds to live) then: sending dialback auth request for route '(full server hostname)/proxy.eu.jabber.org' A couple minutes later, it comes back with: dialback for outgoing route '(full server hostname)/proxy.eu.jabber.org' timed out

  Read the article

• Laptop windows 7 power settings - screen display goes black after 1 minute

  - by Puneet Dudeja

  My laptop windows 7 power settings are not working since last week, i have tried using "Dim display after 5 hours" and "Dim Never" also, but my screen goes black after 1 minute. Any resolutions ? My laptop model is : Compaq Pressario CQ62 Graphics Card Information: Name Intel(R) HD Graphics PNP Device ID PCI\VEN_8086&DEV_0046&SUBSYS_1425103C&REV_02\3&11583659&0&10 Adapter Type Intel(R) HD Graphics (Core i3), Intel Corporation compatible Adapter Description Intel(R) HD Graphics Adapter RAM 1.21 GB (1,303,306,240 bytes) Installed Drivers igdumd64.dll,igd10umd64.dll,igdumdx32,igd10umd32 Driver Version 8.15.10.2119 INF File oem17.inf (iILKM0 section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1366 x 768 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xD03FFFFF Memory Address 0xC0000000-0xCFFFFFFF I/O Port 0x00004050-0x00004057 IRQ Channel IRQ 4294967294 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\igdkmd64.sys (8.15.10.2119, 9.85 MB (10,326,784 bytes), 4/21/2010 6:18 PM) I am not able to solve my problem from any of the answers till now. The screen still goes dark and password screen appears after 1 minute of idle time.

  Read the article

• Is a larger hard drive with the same cache, rpm, and bus type faster?

  - by Joel Coehoorn

  I recently heard that, all else being equal, larger hard are faster than smaller. It has to do with more bits passing under the read head as the drive spins - since a large drive packs the bits more tightly, the same amount of spin/time presents more data to the read head. I had not heard this before, and was inclined to believe the the read heads expected bits at a specific rate and would instead stagger data, so that the two drives would be the same speed. I now find myself looking at purchasing one of two computer models for the school where I work. One model has an 80GB drive, the other a 400GB (for ~$13 more). The size of the drive is immaterial, since users will keep their files on a file server where they can be backed up. But if the 400GB drive will really deliver a performance boost to the hard drive, the extra money is probably worth it. Thoughts?

  Read the article

• How to erase a SSD to restore factory performance in Linux?

  - by Andy B

  Due to big performance issues with an mdraid-1 array I'd like to pull down from the array one of the devices (Samsung 840 Pro), erase it to restore factory performance and re-add it to the array. The reason I want to do this to one of the SSDs is because the poor performance seems to be related to one specific SSD out of the two (although they are the same brand, model and firmware ver). But how do I erase a SSD from Linux? I mention that hdparm indicates that both drives are frozen at this time. Maybe because they are part of an md array? Thanks in advance!

  Read the article

• How to increase signal/range of your Wi-Fi antenna-less repeater/booster over the network?

  - by kenorb

  I've BT Home Hub in the upper flat (2-3 walls behind) and I'm using WPS Wireless-N Wifi Range Router Repeater Extender in my flat where I'm using my laptop. These are antenna-less devices. Are there any life-hack tricks to increase signal/range of my repeater without buying the new more powerful repeater? I've tried already to move my repeater closer to the ceiling or putting the aluminium foil underneath, but it didn't help. Are there any methods, specific plates or materials which can boost the signal? Specification: Model: WN518W2 Frequency range: 2.4-2.4835GHz Wireless transmit power: 14 ~17 dBm (Typical) Wireless Signal Rates With Automatic Fallback: 11n: Up to 300Mbps(dynamic), 11g: Up to 54Mbps(dynamic), 11b: Up to 11Mbps(dynamic) Modulation Technology: DBPSK, DQPSK, CCK, OFDM, 16-QAM, 64-QAM Receiver Sensitivity: 300M: -68dBm@10% PER / 150M: -68dBm@10% PER / 108M: -68dBm@10% PER / 54M: -68dBm@10% PER / 11M: -85dBm@8% PER / 6M: -88dBm@10% PER / 1M: -90dBm@8% PER Product dimensions: 11 * 6 * 7cm

  Read the article

• What are the specifications on the RAM inside my computer?

  - by Faken

  I have a Dell Dimension 9200 that I bought 4 years ago. I want to find out the exact specifications (manufacturer, speed, timings, etc.). Is there a way to get this specific info without having to open up the PC (it's buried in and under a bunch of furniture, I'd perfer not to have to dig it out). All I know about it right now is that it is 4 1GB sticks of DDR2 RAM at 667 Mhz. It is the standard RAM that shipped with the computer 4 years ago (from Dell). Does anyone know what the specifications are of the RAM that Dell used in this particular model of computer 4 years ago? Note: I've done my research before coming here. CPU-Z, EVEREST, and AIDA32 all have been unable to give me any more information other than 4 x 1GB @ 667Mhz. I can't find any specifications in the Dell online manuals either (at least not as specific as I want). Thanks -Faken

  Read the article

• Linksys router with multiple external IP's

  - by Adrian Mester

  In an office I've got a network connection with 5 external IPs and a Linksys router (I'm not 100% percent sure of the model). I need 4 of those 5 IPs to be routed to a server, and the fifth to be shared between the other computers at the office. This can probably be done using a switch in front of the router. Connect the server and the router to the switch, and let the router handle the rest of the network. Is there a way to configure the router to route the 4 IPs to the server, and create an internal network the the other computers at the same time?

  Read the article

• GUID Partition Table & Linux

  - by Zac

  (1) Is it true that the new GUID Partition Table scheme allows a user to partition a drive however he/she like, outside of the traditional MBR "4 primaries or 3 primaries + 1 extension" paradigm? If so, are there any limitations to the GPT? If my assumption is wrong, what are its advantages over the MBR model? (2) I'm getting a new laptop this week and will be installing Ubuntu (and, more generally, Linux) for the first time ever. Does Ubunutu come pre-configured with MBR as a default? If so, how do I get Ubuntu w/ GPT? If not, how do I specify GPT over MBR? Thanks!

  Read the article

• Why would a machine ruin three "power supply"s?

  - by Moshe

  A client of mine has an XP era eMachines. The power supply has died and been replaced 3 times. I've discharged the motherboard and checked the surge protector. In the middle of a scan with ComboFix, the machine died. It powers on and hangs before the BIOS and shows a solid yellow light. I believe the model # is T5062 or something like that. Aside from a bad outlet, what would cause the PSU to die a few times?

  Read the article

• external HDD with SATA & USB interface?

  - by Greg

  Anyone know of an external HDD that would have (in addition to USB) a SATA (eSATA) port/cable? i.e. Brand/Model. Preferably one of the name brands so I have a better change of finding it here or locally if possible. Background - In one location I want to use it is I would like to increase the performance by cabling it directly to the PC SATA port, HOWEVER I don't want to have to open up the PC to do this each time. I was thinking of running a SATA cable out through the PC case so I just plug it directly into the external HDD in question. Perhaps it should be also externally powered too so I don't need to run a power cable out from the PC power supply.

  Read the article

• Visio 2010 Reverse Engineer Oracle

  - by digitall

  I have used Visio 2007 in the past to reverse engineer Oracle databases to get a flow scheme. I believe all Office 2007 products were x86 as well which is where I suspect my issue currently lies. I have since upgraded to Visio 2010 x64 and when I go to reverse engineer something from Oracle it shows up under Installed Visio Drivers but I can't seem to create a data source using it. My assumption here is it is because Oracle doesn't play nicely with x64 and with Visio being compiled as x64 I don't even get the option to use it. Has anyone done this with Visio 2010 x64 and Oracle yet? Or are there other tools you would recommend to reverse engineer and get a model such as the one generated by Visio?

  Read the article

• Why does iChat Server keep connecting to proxy.eu.jabber.org?

  - by Tom Hamming

  I have OS X Server 10.6.5 running on a new Mac Mini (server model), serving several functions among which is iChat Server (iChat and Pidgin on Windows as clients). In the iChat log in Server Admin, I kept seeing entries about connecting to proxy.eu.jabber.org. It's for our office network and I wasn't excited about external access to it, so I disabled server-to-server XMPP federation and now the connections just time out. But why is it doing that in the first place? Sample log entry: (datetime) (servername)jabberd/resolver[portnum]: [xmpp-server._tcp.proxy.eu.jabber.org resolved to 208.68.163.220:5269 (300 seconds to live) then: sending dialback auth request for route '(full server hostname)/proxy.eu.jabber.org' A couple minutes later, it comes back with: dialback for outgoing route '(full server hostname)/proxy.eu.jabber.org' timed out

  Read the article

• Time values not saving in Airport Base Station MAC Timed Access List

  - by Boiler Bill

  I have an airport base station model A1354. I am attempting to setup MAC Timed Access so a laptop can only connect between 5:00AM and 11:00pm through the Airport Utility version 5.5.2 (552.11). My AEBS is running firmware version 7.5.2 When I try to enter the time values by double clicking over the time and entering 05:00 AM and 11:00PM the time values don't stay as soon as it looses focus. Instead they become what is in the following screenshot, and the laptop looses connectivity as soon as I update the base station. I also tried entering the values in military time with the same result. Any base station power users out there that know how I can get the time values to "stick"?

  Read the article

• infiniband network between 3 servers

  - by grumpf

  Let's say I have 3 different servers, each one with an infiniband card. Each card has 2 different ports. (I don't know about the model yet) Is it possible to create 3 different networks and to allow the 3 servers to communicate with each other without any problems? (and any spof). I guess I just have to setup the /etc/hosts correctly. I really don't know about infiniband, so please help me :) Thanks in advance. EDIT: Point is to NOT USE a switch!

  Read the article

• What is the best way to create RAID 1?

  - by user3125731

  I'm looking for a way to create the RAID 1 array without losing my data on CentOS. Here's my situation: I've got a web server running on CentOS. There is one VG partition with few LV volumes. I bought a second HDD (the same model and size as the first one) and I want to create the RAID 1 configuration. I can't just shut down this server for more than an hour because my clients will be disappointed. I need to do this as quickly as possible with minimal risk of data loss.

  Read the article

• Need help. HDD Failed

  - by jiewmeng

  i have a seagate 3.5" 500GB SATA2 HDD that i put in a USB case (vantec) that failed recently. symptoms: at first, it started except that attempts made to browse certain folders resulted in "Data Error (Cyclic Redundancy Check)". then when i tried restarting the hdd, then i got a RAW partition, and windows 7 said i need to format it. i also tried using a desktop to connect to the HDD directly using SATA, windows 7 stuck at "starting windows" for abt half hour b4 i gave up on it. in the BIOS, it seems to detect the HDD model correctly, something like STA3500xxx something like that i also tried using TestDisk as suggested by jaclaz on MSFN and it did not find any partitions what could i do now?

  Read the article

• Calculating IOPS for a single HDD - what am I doing wrong?

  - by red888

  So I know there is no standardized way of calculating IOPS for a HDD, but from everything I have read it appears one of the most accurate formulas is the following: IOP/ms = + {rotational latency} + ({block size} / {data transfer rate}) Which is IOs per millisecond or what the book I've been reading calls "Disk Service Time". Also rotational latency is calculated as half of one rotation in milliseconds. This was taken from the EMC book "Information Storage and Management" -arguably a pretty reliable source right\wrong? Putting this formula into practice consider this Seagate data sheet. I am going to calculate IOPS for the ST3000DM001 model for a block size of 4kb: Seek Average (Write) = 9.5 -I'll measuring IOPS for writes Spindle speed = 7200rpm Average Data Rate = 156MB/s So my variables are: Seek Time = 9.5ms Rotational latency = (.5 / (7200rpm / 60)) = 0.004s = 4ms Data Rate = 156MB/s = (0.156MB/ms / 0.004MB) = 39 9.5ms + 4ms + 39 = IO/ms 52.5 1 / (52.5 * 0.001) = 19 IOPS 19 IOPS for this drive clearly is not right so what am I doing wrong?

  Read the article

• Giving a scanner-printer-combo a zoom function when copying ?

  - by ldigas

  You know how everytime you go to a photocopying shop, photocopiers always have a neat zoom function (it can take whatever you give it, and zoom it in/out, so your copy comes out smaller or larger). I got one of those neat 3-in-one printer machines. It has a copy button on it, but it also has some software that comes with it (Epson SX115 to be exact is the model). Apart from going into some photo manipulation application, is there some way (software) to give it that feature. So, in short, I need something that can scan a page, scale it to let's say, a quarter of its size, and then print it out ? Anyone knows of anything like that ?

  Read the article

• Properly configuring Linux keyboard on my laptop

  - by antoniocs

  Hey! I have a ps/2 keyboard connected to an Acer Aspire 1694 WLMI via a ps/2 to usb converter. The laptop is running Ubuntu 9.04. The keyboard is a HP model number: SK-250C. I have configured in the 'Keyboard Preferences' the layout to HP SK-250x Multimedia Keyboard. The big problem is when I press certain keys (like for example the arrow keys) I get the 'Save Screenshot' dialog. This is really getting annoying, sometimes I am tying to write an address in browser and just want to go back a few letters and can't. There are other keys that trigger the dialog also (windows key, insert key, home key, page up and page down key, delete key, end key) All works fine If I use the laptop keyboard, but I really want to use the HP keyboard. EDIT: I was testing this and it seems that if I have the 'Num Lock' key turned off the keys work properly. Strange but true!!

  Read the article

• Debian no lib32asound2-plugins=1.0.25

  - by erai

  I compiled git wine 1.5.6 and the sound is not working correctly. winecfg gives a message: ALSA lib ../../pulse/pcm_pulse.c:995:(_snd_pcm_pulse_open) Unknown field handle_underrun err:winediag:AUDDRV_GetAudioEndpoint PulseAudio "default" -22 without handle_underrun. Audio may hang. Please upgrade to alsa_plugins >= 1.0.24 err:ole:CoInitializeEx Attempt to change threading model of this apartment from multi-threaded to apartment threaded But on wheezy there is no package lib32asound2-plugins 1.0.25 So, how do I build and package alsa-plugins to install to lib32? Or how do I use automake's configure to compile a 32bit lib on a 64 bit system. All I Need now is the libavcodec-dev for 32bit, but I don't understand. What is the 32bit libavcodec-dev package for amd64 debian?

  Read the article

• My D-Link Router is only allowing one connection

  - by Blaze

  My Router (Model: DI-624) is only allowing one wireless connection to one laptop. The other laptop is stuck hanging at connecting to the Internet I have the SSID set as "Pedro-Home" and is using a WPA PSK secured password. I have set the router using "Blaze-PC" while wired. Both Laptops critically need the Internet. > Dynamic DHCP Client List > > Host Name IP Address MAC > Address Expired Time > Blaze-PC 192.168.0.100 70-f1-a1-ff-39-a8 Apr/21/2011 17:49:14 > pedro 192.168.0.105 00-26-82-c8-47-25 Apr/21/2011 17:50:05 <<This computer isn't connecting.

  Read the article

• How would one run a task sequence within a task sequence in SCCM 2012 SP1

  - by BigHomie

  A Shining Example: Inside all of my task sequences I have a group that installs driver packages conditionally based on computer model: And of course, this list does nothing but grow. The fact that it grows isn't a big deal, what is a big deal is that every time it changes I have to manually copy and paste those changes across every task sequence I have, which of course leaves huge room for human error. The same goes for other groups of tasks that are common across task sequences. Looking for a solution where I could centrally manage these tasks, be it link other task sequences to a group within another task sequence, or create a separate task sequence and link to that. I came across a solution by John Marcum (SCCM MVP) that mentioned this ability, but this was a while ago and I can't find the link to it anymore to see if it's even still being updated/maintained, but I'm looking for more of a free solution, or even using Powershell or the ConfigMgr SDK is fine with me, I'm no stranger to either. Update Getting close: http://msdn.microsoft.com/en-us/library/jj217869.aspx

  Read the article

< Previous Page | 317 318 319 320 321 322 323 324 325 326 327 328  | Next Page >