Search Results

Search found 10169 results on 407 pages for 'port'.

Page 323/407 | < Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >

• How to write files in specific order?

  - by Bernie

  Okay, here's a weird problem -- My wife just bought a 2014 Nissan Altima. So, I took her iTunes library and converted the .m4a files to .mp3, since the car audio system only supports .mp3 and .wma. So far so good. Then I copied the files to a DOS FAT-32 formatted USB thumb drive, and connected the drive to the car's USB port, only to find all of the tracks were out of sequence. All tracks begin with a two digit numeric prefix, i.e., 01, 02, 03, etc. So you would think they would be in order. So I called Nissan Connect support and the rep told me that there is a known problem with reading files in the correct order. He said the files are read in the same order they are written. So, I manually copied a few albums with the tracks in a predetermined order, and sure enough he was correct. So I copied about 6 albums for testing, then changed to the top level directory and did a "find . music.txt". Then I passed this file to rsync like this: rsync -av --files-from=music.txt . ../Marys\ Music\ Sequenced/ The files looked like they were copied in order, but when I listed the files in order of modified time, they were in the same sequence as the original files: ../Marys Music Sequenced/Air Supply/Air Supply Greatest Hits ls -1rt 01 Lost In Love.mp3 04 Every Woman In The World.mp3 03 Chances.mp3 02 All Out Of Love.mp3 06 Here I Am (Just When I Thought I Was Over You).mp3 05 The One That You Love.mp3 08 I Want To Give It All.mp3 07 Sweet Dreams.mp3 11 Young Love.mp3 So the question is, how can I copy files listed in a file named music.txt, and copy them to a destination, and ensure the modification times are in the same sequence as the files are listed?

  Read the article

• award phoenix bios not recognizing my sata hdd.

  - by josh

  What am I doing wrong? I have a custom built comp with a Fatal1ty AA8XE mobo. It has 4 SATA ports and one IDE port. When i first got it, I had a really hard time putting in more than one hard drive. Right now i have one 120gb IDE HDD on master and my DVD+-RW on slave connected to the one IDE spot on the mobo. I ripped a bunch of movies and filled up my HDD, so I got a WD 80gb SATA drive. I plugged it into SATA1 and hooked up the power, turned on comp, went into bios. The only thing in any option in any of the menues in this crazy lookin bios is a thing that says "SATA mode". i put it on IDE, set it so PATA is primary, SATA is secondary. booted up my comp, nothin. Not recognizing the SATA. I went back into the bios and checked it all again. I saw that it says SATA2 and SATA4 are the secondaries so i put it on SATA2, booted, nothing, same with SATA4, same with SATA3, all same as SATA1. Bios and wt os are not recognizing the drive as being there at all. I even downloaded and printed the almost 100 page manual for the mobo, read the entire thing, and still can't figure it out. I know there are a lot of people out there smarter than me when it comes to computers. So please, somebody, anybody, please tell me something that I'm not seeing. Some setting somewhere that I didn't configure right. There is something, obviously, but I can't find it. As far as i can tell, everything is set perfectly fine for my 120gb to be the master and the SATA to be the slave. I don't know what I'm doing wrong but I'm seriously about to throw this computer out the window. thankyou in advance to whoever attempts to help.

  Read the article

• Word documents very slow to open over network, but fine when opened locally - on one machine

  - by Craig H

  Windows XP, Word 2003, patched. The issue is happening with several Word documents stored on a network drive. The Word documents are clearly a bit wonky (i.e. one is 675k, but if you copy everything but the last paragraph marker into a new document, the new document is only 30k). But that's only part of the problem. On one weird machine, and one machine only, it takes ~20 seconds to open these Word documents from the network drive. Copy the file to C: on that werid machine? Opens immediately. Go to other machines (that are very similar - same patch level, etc.) and open the same document from the network? Opens immediately. Delete normal.dot? 20 seconds. Login with a different user on the weird machine? 20 seconds. Plug wonky machine into a different network port? 20 seconds. So the problem appears to be hardware related (i.e. wonky internal NIC) or related to a setting that is not profile specific. Any ideas? "Scrubbing" all the documents isn't ideal for several reasons. This is driving me nuts because I swear I ran into this before many years ago and eventually figured it out. But I appear to have lost my notes.

  Read the article

• Chef: nested data bag data to template file returns "can't convert String into Integer"

  - by Dalho Park

  I'm creating simple test recipe with a template and data bag. What I'm trying to do is creating a config file from data bag that has simple nested information, but I receive error "can't convert String into Integer" Here are my setting file 1) recipe/default.rb data1 = data_bag_item( 'mytest', 'qa' )['test'] data2 = data_bag_item( 'mytest', 'qa' ) template "/opt/env/test.cfg" do source "test.erb" action :create_if_missing mode 0664 owner "root" group "root" variables({ :pepe1 = data1['part.name'], :pepe2 = data2['transport.tcp.ip2'] }) end 2)my data bag named "mytest" $knife data bag show mytest qa id: qa test: part.name: L12 transport.tcp.ip: 111.111.111.111 transport.tcp.port: 9199 transport.tcp.ip2: 222.222.222.222 3)template file test.erb part.name=<%= @pepe1 % transport.tcp.binding=<%= @pepe2 % Error reurns when I run chef-client on my server, [2013-06-24T19:50:38+00:00] DEBUG: filtered backtrace of compile error: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in []',/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:inblock in from_file',/var/chef/cache/cookbooks/config_test/recipes/default.rb:12:in from_file' [2013-06-24T19:50:38+00:00] DEBUG: filtered backtrace of compile error: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in[]',/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in block in from_file',/var/chef/cache/cookbooks/config_test/recipes/default.rb:12:infrom_file' [2013-06-24T19:50:38+00:00] DEBUG: backtrace entry for compile error: '/var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in `[]'' [2013-06-24T19:50:38+00:00] DEBUG: Line number of compile error: '19' Recipe Compile Error in /var/chef/cache/cookbooks/config_test/recipes/default.rb TypeError can't convert String into Integer Cookbook Trace: /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:in []' /var/chef/cache/cookbooks/config_test/recipes/default.rb:19:inblock in from_file' /var/chef/cache/cookbooks/config_test/recipes/default.rb:12:in `from_file' Relevant File Content: /var/chef/cache/cookbooks/config_test/recipes/default.rb: 12: template "/opt/env/test.cfg" do 13: source "test.erb" 14: action :create_if_missing 15: mode 0664 16: owner "root" 17: group "root" 18: variables({ 19 :pepe1 = data1['part.name'], 20: :pepe2 = data2['transport.tcp.ip2'] 21: }) 22: end 23: I tried many things and if I comment out "pepe1 = data1['part.name'],", then :pepe2 = data2['transport.tcp.ip2'] works fine. only nested data "part.name" cannot be set to @pepe1. Does anyone knows why I receive the errors? thanks,

  Read the article

• Looking for updated BIOS for '99 Gateway in order to format/recognize >127 GB HD

  - by Jeff

  I have a '99 Gateway that's apparently too old for even Gateway to acknowledge it exists. Want to use it as a media hub and put in a 320GB HD, but it will not format above 127GB even running Win XP SP3. Read somewhere that upgrading the BIOS may do the trick, but I can't find the correct BIOS, and GW has been no help. Hoping I can just upgrade the BIOS, which is 11 years old. Any help would be much appreciated! I don't know where to look, and searches have been fruitless. System info: OS Name Microsoft Windows XP Home Edition Version 5.1.2600 Service Pack 3 Build 2600 OS Manufacturer Microsoft Corporation System Name xxxx System Manufacturer Gateway System Model TABOR_II System Type X86-based PC Processor x86 Family 6 Model 7 Stepping 3 GenuineIntel ~596 Mhz BIOS Version/Date Intel Corp. 4W4SB0X0.15A.0015.P10, 9/28/1999 SMBIOS Version 2.1 BIOS info (from a free app I located): BIOS Type: Phoenix BIOS Date: September 28th 1999 BIOS ID: 4W4SB0X0.15A.0015.P10.9909281445-None BIOS OEM: 4W4SB0X0.15A.0015.P10 Chipset: Intel 440BX/ZX rev 3 SuperIO: SMC 70x or 80x rev 0 at port 0370 Manufacturer: Gateway Motherboard: WS440BX

  Read the article

• Error 720 on VPN (PPTP) attempt

  - by Andy Shulman

  When I attempt to connect to a server running XP x64 (so essentially Server 2003) using a PPTP connection, it fails with client-side error Registering your computer on the network... Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this configuration. and server-side error Event ID: 20050 The user WINSERV3\Andy connected to port VPN8-1 has been disconnected because no network protocols were successfully negotiated. I have configured the router to pass both TCP packets on 1723 and GRE packets. I have used Wireshark (filtering out ARP, UDP, and all TCP ports other than 1723) to observe the packets received by the server. Wireshark does not explicitly name any protocol GRE, but it does tell me the server sent and received TCP, PPTP, PPP LCP, PPP CHAP, PPP CBCP, and PPP IPCP. The connection seems to go wrong at packet 30, where the protocol is PPP LCP, with the payload of the packet being labeled "Protocol Reject". Obviously, this is going from server to client. This would seem to lead to the conclusion that there is something wrong with my client, which runs Windows 7 Ultimate x64. However, it is able to connect to my house's router, which runs the DD-WRT firmware and is thus a PPTP endpoint. I'm thoroughly at a loss. Please help!

  Read the article

• Migrate installation from one HDD to another?

  - by dougoftheabaci

  I have a server with a 64 GB SSD inside. It runs just fine, but occasionally there's a hiccup that causes it to nearly fill up. When that happens my server starts to lockup and generally misbehave. I'm looking to buy a bigger SSD (either 128 GB or 256 GB) but I'm a bit unsure of how best to make the transition. For a start, I don't have an external monitor. If I need one I'll have to borrow it from work. Most of the time I just SSH into the server from my iMac. The only solution I can think of would be to buy two FW800 2.5" cases, boot from the 64 GB SSD and clone it to the 128 GB SSD. Seem a bit excessive but it might be my best option. I do have more than one SATA port on my server, but they're all currently being use for storage drives. They don't mount by default, so I could unplug them and just have the two SSDs and do the whole thing via SSH. This is another option I'm considering. My main concern with either is how best to make sure everything goes across. I want a carbon copy of the first one onto the second. This is especially important because I have a ZFS volume (my storage) and I'm a bit unfamiliar with how to move everything across. I could just start fresh and reinstall everything on the SSD, but that seems like extra trouble I don't need. So any advice on how best to achieve my goals would be appreciated. Thanks! Server is running Ubuntu Server 12.04. The iMac has 10.8.1.

  Read the article

• How to configure Farsun USB barcode scanner to not auto-trigger

  - by David Grayson

  At my company we have several USB barcode scanners. I'm not sure exactly what model they are, but I think they are the FG9800 from Farsun because that's what they look like on the exterior. They came with a programming manual that is very similar to this document from the Farsun website. When I scan the "Output Firmware Version" barcode, my scanner types the following into the computer: Farsun V2.00 2011-01-01 Is it possible to configure these scanners so they only read barcodes in response to the trigger button being pressed? I don't want them to automatically read barcodes. Additionally, I want this setting to be remembered while the scanner is turned off. Since this scanner only has a USB port, the only way to configure it that I know of is to scan bar codes from the manual (or make your own). I have tried scanning the configuration bar codes for Single Scan (013300), Single Scan No Trigger (013301), and Laser/CCD Timeout - 5 Seconds (0134005) from this document. Sometimes (but not often) this puts the scanner in to the right mode, where it only scans when the button is pressed. Unfortunately, the scanner seems to always leave this mode when it is power cycled. I have also scanned the "Reset Configuration To Defaults" barcode (0B) many times. We have three different scanners like this and I have not been able to successfully configure any of them. If the things I want are not possible with these Farsun-based scanners, is there some other scanner we can use?

  Read the article

• Sshfs is not working..

  - by Devrim

  Hi, When I run sshpass -p 'mypass' sshfs 'root'@'68.19.40.16':/ '/dir' -o StrictHostKeyChecking=no,debug It successfully mounts but it runs on foreground. When I run without 'debug' parameter, it doesn't mount at all. Server is ubuntu 8.04 Any ideas why? UPDATE: When I run the command as ROOT it does mount. It doesn't work with other users. here is the output of an unsuccessful mount $ sshpass -p 'pass' sshfs 'root'@'68.1.1.1':/ '/s6' -o StrictHostKeyChecking=no,sshfs_debug,loglevel=debug debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for * debug1: Connecting to 68.1.1.1 [68.1.1.1] port 22. debug1: Connection established. debug1: identity file /var/www/vhosts/devrim.kodingen.com/.ssh/id_rsa type -1 debug1: identity file /var/www/vhosts/devrim.kodingen.com/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.1p1 Debian-5 debug1: match: OpenSSH_5.1p1 Debian-5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_4.7p1 Debian-8ubuntu1.2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY Warning: Permanently added '68.1.1.1' (RSA) to the list of known hosts. debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password debug1: Next authentication method: publickey debug1: Trying private key: /var/www/vhosts/devrim.kodingen.com/.ssh/id_rsa debug1: Trying private key: /var/www/vhosts/devrim.kodingen.com/.ssh/id_dsa debug1: Next authentication method: password debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_GB.UTF-8 debug1: Sending subsystem: sftp Server version: 3 debug1: channel 0: free: client-session, nchannels 1 debug1: fd 0 clearing O_NONBLOCK debug1: Killed by signal 1.

  Read the article

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• Short POST data in HTTP

  - by Matt

  We're hosting a customer's Debian Linux web server. It's running a PHP based web application. The server is sitting behind our firewall with it's own virtual interface and port 80 is forwarded internally to a machine sitting in the DMZ. The issue we're having is that when data is posted to the server it seems to be being cut short for some users. It's reproducable for some users on the same box. But the same user sending the same data on the same lan on another PC it works. The data gets cut to around 1140 bytes I'm told. Any idea why this might be happening? The customer is blaming our firewall, but then surely we'd have issues with other services. I'm suspecting it's a problem with the website itself. Suggestions on how to isolate the problem would be of help. Our firewall is Astaro. EDIT: A customer has set the ethernet frame size temporarily to 500bytes on the server. This made it work for now! I know some of the customers are using an internet provider that runs PPPoE

  Read the article

• Using Virtualbox Bridge Networking fails connection from Guest OS to Oracle XE running on Host

  - by Licheng

  I am trying to make a JDBC connection from a VirtualBox Ubuntu Guest OS to an Oracle XE database running o Host. However, the connection is refused. Here are the details of my environment: VirtualBox: 4.1.4 Host OS: Windows 7 Guest OS: Ubuntu server 11.4 Networking mode: Bridged network Oracle XE database running on Host Issue: WebLogic server runs on the Ubuntu virtualbox. It attempts to connect to an Oracle XE database running on the Host OS (windows 7) with listening port 1521. On the Guest OS (Ubuntu), I am able to ping the Host computer from the Guest OS. However, when I configured a JDBC data source on the WebLogic server on the Guest OS to connect to the Oracle XE, connection took a long time, and eventually I received an "IO Exception: The Network Adapter could not establish the connection". When I tried "telnet host-ip 1521", no connection was established. With Bridge networking, I can make bi-directional connections between the host and the guest OS (e.g. connection through ssh and ftp). Is there anything I missed in the setup of Bridge networking and the guest/host OS? Note that I was able to make the same connection within a normal networking environment (i.e. not using virtual box). I am not sure whether Bridge networking is a good option for the work described above. Should I use host-only networking mode? If so, any specific configurations I need to perform? I read through the Virtual box document on setting up the host-only network, however, it lacks of details. I followed the procedures described in the manual, and couldn't even connect to the host. Could some experts here enlighten me on this issue? Much appreciated. Licheng

  Read the article

• Unable to connect to EC2 instance after "reboot"

  - by KPL

  I am not able to connect to my m1.small instance after rebooting it. I have already associated the public IP with this instance. Upon checking the system log, this seems to be the issue: cloud-init-nonethttp://11.84: waiting 10 seconds for network device cloud-init-nonethttp://21.85: waiting 120 seconds for network device cloud-init-nonethttp://141.85: gave up waiting for a network device. Cloud-init v. 0.7.3 running 'init' at Sun, 18 May 2014 07:02:55 +0000. Up 142.54 seconds. ci-info: +++++++++++++++++++++++Net device info++++++++++++++++++++++++ ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | Device | Up | Address | Mask | Hw-Address | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: | lo | True | 127.0.0.1 | 255.0.0.0 | . | ci-info: | eth0 | False | . | . | 02:43:xx:xx:xx:xx | ci-info: +--------+-------+-----------+-----------+-------------------+ ci-info: !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Route info failed!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! A bunch of these follow the above message: 2014-05-18 07:02:56,178 - url_helper.pyWARNING: Calling http://169.254.169.254/2009-04-04/meta-data/instance-id failed 0/120s: request error [HTTPConnectionPool(host='169.254.169.254', port=80): Max retries exceeded with url: /2009-04-04/meta-data/instance-id (Caused by : Errno 101] Network is unreachable) This is obviously related to the network interface not being working correctly. I have tried this so far: Relaunch a new instance from the custom AMI (created from EBS) of the failing instance. The same error shows up in the logs. Attach a new network interface to the EC2 instance. The error still persists. eth1 shows up in the list but the "up" column is False.

  Read the article

• Cisco SG 300-28P PoE switch appears to have damaged my domain server's network IF

  - by cdonner

  I just replaced the old HP ProCurve switch with a new Cisco SG 300-28P managed switch. It has PoE on all ports. Everything works, except for my domain server that went offline and the network interface appears to be dead. Windows says the network cable is disconnected, and no lights blink on the switch. Tried different cables and different ports on the switch. The Cisco PoE ports are supposed to be auto-sensing, i.e. not to send power to a device that cannot handle it. Is this technique not 100% reliable? The server is a SHUTTLE XS35V2 with an onboard network chip, so it is probably fried. My questions: is this plausible? who's fault is it - Shuttle or Cisco (i.e. which support line should I try first)? UPDATE: I did go back and tried another switch between the server and the Cisco switch, and indeed, the connection came back to live. When everything is powered down and I start fresh, with the server connected to the Cisco switch, the port light will blink for a while and the connection status is "No Internet connection" at first until it goes off after about 20 seconds and the connection status changes to "Network cable disconnected". On the other switch it works. Clearly not a PoE issue now. I will start looking into the Cisco's onboard diagnostic functions, but so far I have not noticed anything unusual in the log.

  Read the article

• Bash Script - Traffic Shaping

  - by Craig-Aaron

  hey all, I was wondering if you could have a look at my script and help me add a few things to it, How do I get it to find how many active ethernet ports I have? and how do I filter more than 1 ethernet port How I get this to do a range of IP address? Once I have a few ethenet ports I need to add traffic control to each one #!/bin/bash # Name of the traffic control command. TC=/sbin/tc # The network interface we're planning on limiting bandwidth. IF=eth0 # Network card interface # Download limit (in mega bits) DNLD=10mbit # DOWNLOAD Limit # Upload limit (in mega bits) UPLD=1mbit # UPLOAD Limit # IP address range of the machine we are controlling IP=192.168.0.1 # Host IP # Filter options for limiting the intended interface. U32="$TC filter add dev $IF protocol ip parent 1:0 prio 1 u32" start() { # Hierarchical Token Bucket (HTB) to shape bandwidth $TC qdisc add dev $IF root handle 1: htb default 30 #Creates the root schedlar $TC class add dev $IF parent 1: classid 1:1 htb rate $DNLD #Creates a child schedlar to shape download $TC class add dev $IF parent 1: classid 1:2 htb rate $UPLD #Creates a child schedlar to shape upload $U32 match ip dst $IP/24 flowid 1:1 #Filter to match the interface, limit download speed $U32 match ip src $IP/24 flowid 1:2 #Filter to match the interface, limit upload speed } stop() { # Stop the bandwidth shaping. $TC qdisc del dev $IF root } restart() { # Self-explanatory. stop sleep 1 start } show() { # Display status of traffic control status. $TC -s qdisc ls dev $IF } case "$1" in start) echo -n "Starting bandwidth shaping: " start echo "done" ;; stop) echo -n "Stopping bandwidth shaping: " stop echo "done" ;; restart) echo -n "Restarting bandwidth shaping: " restart echo "done" ;; show) echo "Bandwidth shaping status for $IF:" show echo "" ;; *) pwd=$(pwd) echo "Usage: tc.bash {start|stop|restart|show}" ;; esac exit 0 thanks

  Read the article

• Gluster bricks are offline and errors in logs

  - by Roman Newaza

  I have substituted all the IP addresses with hostnames and renamed configs (IP to hostname) in /var/lib/glusterd by my shell script. After that I restarted Gluster Daemon and the volume. Then I checked if all the peers are connected: root@GlusterNode1a:~# gluster peer status Number of Peers: 3 Hostname: gluster-1b Uuid: 47f469e2-907a-4518-b6a4-f44878761fd2 State: Peer in Cluster (Connected) Hostname: gluster-2b Uuid: dc3a3ff7-9e30-44ac-9d15-00f9dab4d8b9 State: Peer in Cluster (Connected) Hostname: gluster-2a Uuid: 72405811-15a0-456b-86bb-1589058ff89b State: Peer in Cluster (Connected) I could see mounted volumes size change on all the nodes when I execute df command, so new data is coming. But recently I noticed error messages in app log: copy(/storage/152627/dat): failed to open stream: Structure needs cleaning readfile(/storage/1438227/dat): failed to open stream: Input/output error unlink(/storage/189457/23/dat): No such file or directory Finally, I have found out some bricks are offline: root@GlusterNode1a:~# gluster volume status Status of volume: storage Gluster process Port Online Pid ------------------------------------------------------------------------------ Brick gluster-1a:/storage/1a 24009 Y 1326 Brick gluster-1b:/storage/1b 24009 N N/A Brick gluster-2a:/storage/2a 24009 N N/A Brick gluster-2b:/storage/2b 24009 N N/A Brick gluster-1a:/storage/3a 24011 Y 1332 Brick gluster-1b:/storage/3b 24011 N N/A Brick gluster-2a:/storage/4a 24011 N N/A Brick gluster-2b:/storage/4b 24011 N N/A NFS Server on localhost 38467 Y 24670 Self-heal Daemon on localhost N/A Y 24676 NFS Server on gluster-2b 38467 Y 4339 Self-heal Daemon on gluster-2b N/A Y 4345 NFS Server on gluster-2a 38467 Y 1392 Self-heal Daemon on gluster-2a N/A Y 1402 NFS Server on gluster-1b 38467 Y 2435 Self-heal Daemon on gluster-1b N/A Y 2441 What can I do about that? I need to fix it. Note: CPU and Network usage of all the four nodes are about the same.

  Read the article

• SSH hangs without password prompt

  - by Wilco

  Just reinstalled OS X and for some reason I now cannot connect to a specific machine on my local network via SSH. I can SSH to other machines on the network without any problems, and other machines can SSH to the problematic one as well. I'm not sure where to start looking for problems - can anyone point me in the right direction? Here's a dump of a connection attempt: OpenSSH_5.1p1, OpenSSL 0.9.7l 28 Sep 2006 debug1: Reading configuration data /etc/ssh_config debug1: Connecting to 10.0.1.7 [10.0.1.7] port 22. debug1: Connection established. debug1: identity file /Users/nwilliams/.ssh/identity type -1 debug1: identity file /Users/nwilliams/.ssh/id_rsa type -1 debug1: identity file /Users/nwilliams/.ssh/id_dsa type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_4.5 debug1: match: OpenSSH_4.5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '10.0.1.7' is known and matches the RSA host key. debug1: Found key in /Users/nwilliams/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,gssapi-keyex,gssapi-with-mic,password,keyboard-interactive debug1: Next authentication method: gssapi-keyex debug1: No valid Key exchange context debug1: Next authentication method: gssapi-with-mic ... at this point it hangs for quite a while, and then resumes ... debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information Server not found in Kerberos database debug1: Unspecified GSS failure. Minor code may provide more information debug1: Next authentication method: publickey debug1: Trying private key: /Users/nwilliams/.ssh/identity debug1: Trying private key: /Users/nwilliams/.ssh/id_rsa debug1: Trying private key: /Users/nwilliams/.ssh/id_dsa debug1: Next authentication method: keyboard-interactive

  Read the article

• Java exception when the traffic grow up

  - by sahid

  I have an error with java/solr when the traffic grows up. It seems Solr tries to cast a java.lang.Object to a org.apache.solr.common.util.ConcurrentLRUCache$CacheEntry SEVERE: java.lang.ClassCastException: [Ljava.lang.Object; cannot be cast to [Lorg.apache.solr.common.util.ConcurrentLRUCache$CacheEntry; at org.apache.solr.common.util.ConcurrentLRUCache$PQueue.myInsertWithOverflow(ConcurrentLRUCache.java:377) at org.apache.solr.common.util.ConcurrentLRUCache.markAndSweep(ConcurrentLRUCache.java:329) at org.apache.solr.common.util.ConcurrentLRUCache.put(ConcurrentLRUCache.java:144) at org.apache.solr.search.FastLRUCache.put(FastLRUCache.java:131) at org.apache.solr.search.SolrIndexSearcher.getDocSet(SolrIndexSearcher.java:573) at org.apache.solr.search.SolrIndexSearcher.getDocSet(SolrIndexSearcher.java:641) at org.apache.solr.search.SolrIndexSearcher.getDocListNC(SolrIndexSearcher.java:1109) at org.apache.solr.search.SolrIndexSearcher.getDocListC(SolrIndexSearcher.java:1090) at org.apache.solr.search.SolrIndexSearcher.search(SolrIndexSearcher.java:337) at org.apache.solr.handler.component.QueryComponent.process(QueryComponent.java:431) at org.apache.solr.handler.component.SearchHandler.handleRequestBody(SearchHandler.java:231) at org.apache.solr.handler.RequestHandlerBase.handleRequest(RequestHandlerBase.java:129) at org.apache.solr.core.SolrCore.execute(SolrCore.java:1298) at org.apache.solr.servlet.SolrDispatchFilter.execute(SolrDispatchFilter.java:340) at org.apache.solr.servlet.SolrDispatchFilter.doFilter(SolrDispatchFilter.java:240) at org.apache.catalina.core.ApplicationFilterChain.internalDoFilter(ApplicationFilterChain.java:235) at org.apache.catalina.core.ApplicationFilterChain.doFilter(ApplicationFilterChain.java:206) at org.apache.catalina.core.StandardWrapperValve.invoke(StandardWrapperValve.java:233) at org.apache.catalina.core.StandardContextValve.invoke(StandardContextValve.java:191) at org.apache.catalina.authenticator.AuthenticatorBase.invoke(AuthenticatorBase.java:470) at org.apache.catalina.core.StandardHostValve.invoke(StandardHostValve.java:127) at org.apache.catalina.valves.ErrorReportValve.invoke(ErrorReportValve.java:102) at org.apache.catalina.core.StandardEngineValve.invoke(StandardEngineValve.java:109) at org.apache.catalina.connector.CoyoteAdapter.service(CoyoteAdapter.java:298) at org.apache.coyote.http11.Http11Processor.process(Http11Processor.java:857) at org.apache.coyote.http11.Http11Protocol$Http11ConnectionHandler.process(Http11Protocol.java:588) at org.apache.tomcat.util.net.JIoEndpoint$Worker.run(JIoEndpoint.java:489) at java.lang.Thread.run(Thread.java:636) This is my java configuration for tomcat JAVA_OPTS="-Djava.awt.headless=true -D64 -server -Xms4096M -Xmx4096M -XX:+UseConcMarkSweepGC -Dcom.sun.management.jmxremote -Dcom.sun.management.jmxremote.port=5400 -Dcom.sun.management.jmxremote.ss\ l=false -Dcom.sun.management.jmxremote.authenticate=false" Somebody know why these errors happen ?

  Read the article

• Chroot jail of Nginx and php

  - by sqren

  I'm hosting multiple websites on one VPS, and want to chroot each website, eg. /chroot/website1 /chroot/website2 I'm using makejail, which is a highlevel tool, for creating the jails, and copying the libraries and dependencies. Easy peasy. Each website will need nginx, php and mysql. For php I'm using php5-fpm which actually supports chroot by configuration, however I'm not using this (maybe I should?) My question is which approach of the following three is the better: 1) Every website will have its own seperated instance of nginx, php and mysql. The downside is, that each webserver + php has to listen to a different port. I also need a "master" nginx web server in front of them, reverse proxying to the chrooted servers behind it. Probably most secure, but also most advanced. 2) I don't make any chroot jails manually. I setup one nginx web server, that proxies php requests to php-fpm, on different ports. I can have multiple php-fpm configurations each with is own chroot'ed folder. This is quite managable - however only php will be chrooted. Not the actual webserver. Is this secure enough. Also, I tried this option out, and it seems I will need to use TCP instead of sockets for connecting to MySQL. 3) You tell me ;) I'm quite new to chroot jailing, so please correct me if I'm wrong in my assumptions. I've been reading all the tutorials I could find, however, I find the market for chroot guides very scarce. Any help or inputs much appreciated!

  Read the article

• How to configure a Router (TL-WR1043ND) to work in WDS mode?

  - by LanceBaynes

  I have a WRT160NL router (192.168.1.0/24 - OpenWrt 10.04) as AP. It's: - WAN port: connected to the ISP - WLAN: working as an AP, using 64 bit WEP/SSID: "MYWORKINGSSID", channel 5, using password: "MYPASSWORDHERE" - It's IP Address is: 192.168.1.1 Ok! It's working great! But: I have a TL-WR1043ND router that I want to configure as a "WDS". (My purpose is to extend the wireless range of the original WRT160NL.) Here is how I configure the TL-WR1043ND: 1) I enable WDS bridging. 2) In the "Survey" I select my already working network. 3) I set up the encryption (exact same like the already working one) 4) I choose channel 5 5) I type the SSID 6) I disable the DHCP server on it. After I reboot the router and connect to this router (TL-WR1043ND) over wireless I'm trying to ping google.com. From the ping I see that I can reach this router, that's ok, but it seems like that this router can't connect to the original one, the WRT160NL (so I don't get ping reply from Google). The encryption settings/password is good I checked it many-many-many times. what could be the problem? I'm thinking it could be a routing problem, but what should I add to the "Static Routing" menu? I tried to change the IP address of the TL-WR1043ND to: 192.168.1.2 So if this a routing issue then I should add a static routing rule that says: If destination: any then forward the packet to 192.168.1.1 p.s.: I updated the Firmware to the latest version. It's still the same. p.s.2: The HW version of the TL-WR1043ND is 1.8 p.s.3: Could that be the problem that I use different routers? (If I would buy.. another TL-WR1043ND and use it instead of the WRT160NL, and with normal Firmware, not OpenWrt, then it would work?? The "WDS" is different on different routers?) p.s.4: I will try to check the router logs@night - and paste it here! :\

  Read the article

• PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded

  - by Tiny

  I'm trying to upgrade php 5.4.14 from php 5.4.3 in wamp server 2.2e. I have downloaded php-5.4.14-Win32-VC9-x86 (thread safe). Extracted it under C:\wamp\bin\php. Copied wampserver.conf from C:\wamp\bin\php\php5.4.3 to C:\wamp\bin\php\php5.4.14. Renamed php.ini-development to phpForApache.ini. -The port number the wamp server has been changed in the http.conf file to 8087 from its default 80. This is mentioned here though it is about upgrading from php 5.3.5 to php 5.4.0. After this, Restarting of the wamp server and services all over again has all been done and those two versions appeared in the menu php-versions (which is opened when the icon of the server is clicked). But when I attempt to enable a library like php_mysql or php_mysqli, a warning message box appears. PHP Startup: Unable to load dynamic library 'C:"\php\php_mysql.dll' - The specified module could not be loaded. I have also tried to removing the semicolon before them in the php.ini file but to no avail. I'm running Microsoft Windows XP Professional Version 2002, service pack 3. Where might be the problem? EDIT: I have changed extension_dir from C:\php to c:\wamp\bin\php\php5.4.14\ext\ in php.ini as the answer below indicates and the library is now loaded correctly but it says, 1045 - Access denied for user 'root'@'localhost' (using password: YES) though the user name and the password are the same as they are in MySQL in the config.inc.php file under phpmyadmin. I have also tried to restart MySQL56 service from Control Panel-Services(Local) but it keeps giving the same error. Does someone know why this happens?

  Read the article

• Weird permission issue with POSIX ACLs, NFS v3 on Linux

  - by jon

  I have two Linux systems, both running Debian Squeeze. Versions of (I think) the stuff involved are: kernel: 2.6.32-5-xen-amd64 ii nfs-kernel-server 1:1.2.2-4squeeze2 support for NFS kernel server ii libnfsidmap2 0.23-2 An nfs idmapping library ii nfs-common 1:1.2.2-4squeeze2 NFS support files common to client and server ii portmap 6.0.0-2 RPC port mapper (The client doesn't have nfs-kernel-server involved.) I have a directory with ACLs: # file: dirname # owner: jon # group: foogroup # flags: -s- user::rwx user:www-data:rwx group::r-x group:foogroup:rwx mask::rwx other::r-x default:... There are two users, neither one of which owns the directory: uid=3001(jake) gid=3001(jake) groups=3001(jake),104(wheel),3999(foogroup) uid=3005(nic) gid=3005(nic) groups=3005(nic),3999(foogroup) The jake user can create files in the directory without issues. The nic user can't. All UIDs/GIDs are the same on the client and server. I've verified (packet sniffing) that the right uids/gids get sent via AUTH_UNIX are correct-- uid=gid=3005, auxiliary gids=3005,3999-- and that the server replies with NFS3ERR_ACCESS, which the kernel on the client maps to EACCES (Permission denied). Can anyone help me here?

  Read the article

• remote telnet and email

  - by Mustafa Ismail Mustafa

  This issue has been occupying my work for the last few days and I will be understating when I say its driven me up the blasted walls. Essentially, I can ping and tracert the domain jnrcs.org and the subdomains mail.jnrcs.org and mail.jordanredcrescent.org. All three mentioned point to ip address 212.38.147.97. About 4 days ago, when we registered the domain "jnrcs.org" suddenly all external connection to the mail server from outside was lost. Not just mail, but other http based port-forwarded or natted services (such as camera surveillance and pbx services). I tried good old telnet (I'm a linux user) and I get the following output: telnet> o mail.jnrcs.org 25 Trying 212.38.147.97... telnet: Unable to connect to remote host: No route to host telnet> Tracert gives me: traceroute to mail.jnrcs.org (212.38.147.97), 30 hops max, 60 byte packets 1 192.168.1.2 (192.168.1.2) 0.869 ms 0.944 ms * 2 * * * 3 * * * 4 * * * 5 * * * 6 * 212.38.128.118 (212.38.128.118) 33.875 ms 39.187 ms 7 * * * 8 * * * 9 * * * 10 * * * 11 * * 212.38.147.97 (212.38.147.97) 67.621 ms I am stumped. Other friends from all around the world can telnet no problem. What could have possibly happened to make telnet/smtp/pop/imap/http access stop? Please bear in mind I'm primarily a developer but I [am under the delusion] that I can carry my weight in IT administration :) TIA

  Read the article

• Installing SATA dvd burner on machine with no spare SATA ports/connectors

  - by Faheem Mitha

  Greetings. I have the following motherboard Tyan Thunder K8WE S2895A2NRF Motherboard - extended ATX - nForce Pro 2200/2050 - Socket 940 - UDMA133, Serial ATA-300 (RAID) - 2 x Gigabit Ethernet - FireWire - 6-1 channel audio This is part of a computer that was assembled in the winter of 2006/2007. The user manual says the following with regard to SATA Integrated SATAII Generation 1 Controllers (from NForce Professional 2200) Two integrated dual port SATA II controllers Four SATA connectors support up to four drives 3 Gb/s per direction per channel NvRAID v2.0 support Supports RAID 0, 1, 0+1 and JBOD. I just purchased a SATA DVD burner. Here is the page for the product http://www.amazon.ca/gp/product/B002QGDWLK/ The problem I am facing is that I already have 4 SATA drives installed. I don't want to remove any of them. However, I want the DVD burner above installed as well. The person I am consulting with here (Bombay, India) tells me that my four available SATA ports are filled, and that my only option is to install a SATA card into the one free PCI slot on the motherboard. However, he says that with this setup I will not be able to boot from the DVD drive. Are these statements correct, and what are my other options if any? Even it the statements in the last para are true, I suppose I could use one of the motherboard connectors/ports there are currently being used with the hard drives with the DVD drive, and use the "add-on" connector with one of the hard drives. Not all the 4 hard drives need to be bootable. BTW, despite having read through http://en.wikipedia.org/wiki/Serial_ATA#Cables.2C_connectors.2C_and_ports I am fuzzy on the differences between connectors, cables and ports. Thanks in advance.

  Read the article

• Can't connect to a Hyper-V VM from anywhere but the host OS

  - by Elbelcho

  I have an unusual situation on hand where I'm able to connect to a Hyper-V guest VM from the HOST, but not from anywhere but the host. The VM is running WIn2k8R2 and has IIS installed and Remote Desktop enabled. If I browse to the IP from the host OS, the IIS7 page displays. I can also RDP into the guest OS from the host as well as ping. From OFF the host, RDP, web and ping all fail. If I completely shut off the guest VM's firewall, ping will then start to respond, but all RDP and port 80 still don't. The physical host machine has 2 nics installed, but only one is plugged in. The one plugged in has a static IP. I have one Hyper-V virtual network and it's set to external. The guest VM has one NIC with a different static IP than the host, but both are on the same subnet. The host machine is joined to the domain, the guest VM is not. Any sugestions? Thanks so much for any help you may be able to provide!

  Read the article

< Previous Page | 319 320 321 322 323 324 325 326 327 328 329 330  | Next Page >