Search Results

Search found 10215 results on 409 pages for 'ram usage'.

Page 326/409 | < Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >

• Why does my PC successfully boot only when unplugged for more than a few minutes?

  - by philg

  I have an HP Pavilion Elite desktop computer, model HPE-490t. I like it because it didn’t cost too much, boots itself from an SSD, came with 16 GB of RAM, and has 6 CPU cores for editing video and camera RAW images. It has one behavioral quirk that I cannot explain, however. The recent power interruptions here in the Northeast got the machine into a state where it could not be restarted. It would power up for a second or two, shut down, and then power up again, never being able to get to the point of showing anything on the monitor. I unplugged it for about 10 seconds and plugged it back in. Same behavior (fails to boot). I unplugged it and walked away for an hour, then plugged it back in and it worked perfectly! I think something similar happened after installing a second hard disk drive into this machine. So the question is why does the computer behave differently depending on how long it has been unplugged? Where is energy stored that affects the machine’s ability to boot? Capacitors in the power supply? Battery on the motherboard (there is one for the clock, but that wouldn’t be exhausted by being unplugged for an hour, I don’t think)?

  Read the article

• AGP 4x slot running at 2x

  - by Wesley

  Hi all, Here are the specs of the machine related to this question: AMD Athlon XP 2400+ @ 2 GHz / 2x 512MB PC3200 DDR RAM / 3D Fuzion 128MB GeForce 6200 AGP / WD 160GB IDE HDD / FIC AM37 (mobo) / Codegen 350W PSU / Windows XP Pro SP3 So, for some odd reason, the GeForce 6200 that is in the AGP 4x slot is not running at 4x, but 2x. The card itself supports AGP 4x and even 8x. When I enter the BIOS, the options for the AGP slot only allow 2x as the max. Before, the max option for the AGP slot in the BIOS was 4x. (I do get the 4x option after I reset CMOS, but it does not stick after a restart.) I don't exactly know what the problem could be, but a few weeks ago, this machine's hard drive was reformatted and got a fresh install of XP. Also, I did install Rivatuner, but I never overclocked it at all. (I uninstalled it after thinking that it had done something.) Otherwise, I cannot figure out the cause of the problem. Does anybody have an idea why this is happening? (Would I have to do another reformat?) Thanks in advance. PS: the other options for the AGP slot are aperture size (which I tried changing, but it did nothing) and FastWrite (enabled by default).

  Read the article

• SharePoint 2010 Enterprise wiki - [New page] missing

  - by icelava

  I am trying to ramp up knowledge on SharePoint deployment and usage (never did before), due to a direction to use SharePoint 2010 as a repository platform (wiki format) for our customer's infrastructure documentation. In my test virtual server, a new site of Enterprise wiki template was setup. Went into Site Actions Manage Site Features to activate Wiki Page Home Page. The default sub-web then went from /Pages to /SitePages and looks like the default Team template. The odd thing is the Site Actions is missing the New Page option. My colleague does not understand why this is the case, as it ought to be there. The original /Pages sub-web does have the option. What conditions are in play that influences the appearance of that option? UPDATE Another phenomenon observed is in the Site Actions View All Site Content view, the wiki document libraries listed in the grid will have their hyperlink (e.g. "Site Pages") lead straight to the direct default page. It would not show its own table listing of pages under that document library, unlike the original Pages document library, which expectedly show up as a listing. I wonder if this hints to any problems.

  Read the article

• which grabber is good enough to get 1000fps?

  - by user261002

  I have two framegrabber with a fast camera (1800+ fps). can anybody who understand the hardware, explain to me which of the following grabbers can help me more to grab 1000fps ? here are the the features of the two grabbers : Inspecta-5 Full Camera Link® Version: · Support for line scan and area cameras. · Video data rate of up to 660 Mbytes/sec. · PCI – X bus interface for 64 Bit data width and 66 MHz clock frequency. · PCI bus interface for 32 Bit data width and 33 MHz clock frequency. · 2 Gigabyte Onboard Memory for fast video streams. · Four opt coupled input- output ports for external trigger and encoder signals. · 528 Mbytes/sec. maximum data rate on the PCI–X Bus. · SDK for Windows 2000/XP SILICONSOFTWARE V-Series Camera Link : “microEnable IV VD4-CL” · Camera Pixel Clock Support 85 MHz · Area Scan Cameras 32k * 64k max. image size · Line Scan Cameras 64k max. image width · Acquisition Buffer: 512 MB DDR-RAM · Sustainable Transfer Rate (max.) 850 MBytes/sec. · microEnable SDK for Windows XP/Vista/ 7/ Linux

  Read the article

• What are these CPU cache settings? Snoop Filter, ACL prefetch, HW prefetch

  - by eater

  I was in my BIOS setup turning on VT-x support today and saw these other settings. A little googling indicates that they each seem to turn on some sort of optimization to do with the CPU's L2 cache. They were all turned off by default. The processor in question is an Intel Xeon quad-core 3.4GHz (X5492). My OS is Linux 2.6.35.10-74.fc14.x86_64 #1 SMP Thu Dec 23 16:04:50 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux. I have 4GB of RAM if that matters. Here's what the BIOS manufacturer has to say: Snoop Filter Enabling the snoop filter typically improves performance by reducing snoop traffic on the frontside bus in dual processor configurations. Well I like the sound of improved performance. Why would the BIOS have this off by default? Or by dual processor do they not mean multi-core? Regardless, is there a downside if this is on? ACL Prefetch When enabled, the Adjacent Cache Line Prefetcher fetches both cache lines that comprise a cache line pair when it determines required data is not currently in its cache. When disabled, the processor will only fetch the cache line required by the processor. HW Prefetch Fetches an extra line of data into L2 from external memory. Both of these sound like optimizations that have some drawbacks. What are the reasons to turn them on? What are the reasons to leave them off. Why is the default off?

  Read the article

• Power issues Foxconn Barebones kit

  - by alpha1

  I have a Foxconn R20D2 bought about a year and a half ago. It ran fine for a while and then around last summer it started having power issues. I chalked it up to changes in electric current due to the overwhelmed grid when people turn on their AC units, but this problem has stayed for all year, shutting off randomly, shutting off when i turn on a vacuum and similar problems. Now that its summer again, the box basically sits there all day cycling itself, and now has gotten to the point it tried to boot and after 3 seconds, fails, shuts off and tried again. I know its power related, it runs opensuse linux and there are never any shutdown logs or anything of that sort. As the weather got hotter i noticed it happening more and more, and it most often happened in the morning, i presume as people woke up and turn on the AC. The power supply is a Chennel well technology co LTD model DSL-150. 150W max output. Its an intel atom dual core, with 2 sata drives, no CD/floppy etc, recently upgrades from 2 to 4gb of ram. It runs at 104 degrees Fahrenheit all the time almost. Any way i can test the power supply or anything else to try to fix it? Im a software guy, not hardware so im at a complete loss here, thanks for all assistance you can provide! EDIT: The switch on the back that says 230 or 115 is set to 230. If im in the USA, could that be causing the problems?

  Read the article

• Partitioning & Linux

  - by Zac

  Every tutorial on Linux-based partitioning schemes (or, just partitioning in general) will tell you that a PC can have either 4 primary partitions, or 3 primaries and 1 extended. They will all also tell you that Linux (in my case, Ubuntu) can be installed on either. It's also come to my attention that it is not too atypical for FHS directories, such as usr/, tmp/, etc/, home/ or var/ to be mounted separately on other partitions. Several questions I am unable to find the answers to, purely for my own edification: (1) By "PC", are we really talking about common PC disk types, like IDE or SATA? I guess I'm wondering why PC uses are limited to 4 primaries or 3 primaries + 1 extended (2) I'm choking on some basic OS concepts: it is said that a partition can be mounted by a file system or an OS. So I assume this means I can somehow instruct Ubuntu to mount to 1 partition, and then any part of, say, ReiserFS, to be mounted to another partition? How? (3)(a) What about creating swap partitions? Is there too much of a good thing with swap partitioning? If I have 4GB RAM over 320GB disk, what should my swap partition size be, and why? (3)(b) Are swap files the only way to create swap partitions? Wouldn't a Linux partitioning utility allow me to define a partition as being for virtual memory only? (4) Why are partitions limited to being "mounted" by just OSes and file systems? Why couldn't I write a program to take up its own, say, 512 MB partition, and then have it invoked or uses by an OS installed on another partition? Thanks for shedding any light here... not critical that I know this stuff, but it's got me thinking incessantly. And when I think incessantly, I...can't......sleep....

  Read the article

• How to run Fujitsu P27T-7 LED monitor in its not native resolution and have perfect fonts rendering

  - by Ilia Rostovtsev

  My problem is completely opposite to anything I could find as I need to run my monitor in its NOT native resolution and have perfect font rendering. I recently got myself Ultra HD 2560x1440 27 inch monitor (Fujitsu P27T-7 LED) and I have an issue with this. I would call it personal but I'm afraid it's not as few people already agreed with me. I do programming and the text on UHD is way to small for comfortable usage. I changed the resolution to regular Full HD (1920x1080), it became just right but the text is looking slightly blur now, in comparison to both its natural UHD resolution and/or to my old 23 inch NEC. I am pretty frustrated and not sure what to do and how to make fonts look just as sleek as they should? I can't work in UHD resolution (my vision is 100% perfect), simply if calculated, picture size with Ultra HD (2560x1440) on 27 inch is around 30% smaller than Full HD (1920x1080) on 23 inch. In order to have same font size, if compared with Full HD 23 inch, 27 inch Ultra HD monitor must be around 32 inches in size. If I set my new monitor to regular Full HD 1920x1080, then the fonts' size are just perfect but the quality is not as it's blurry? Could anyone please help me out with an advise of how to solve this problem? Spec: nVidia 560 Ti with DVI-D port on Fedora 20. EDIT 1: Changing fonts doesn't really help as everything else doesn't look the way it should. EDIT 2: The monitor is buzzing on 2560x1440 so badly in case there are lots of lines on the screen, like file listing. If I type ls /usr/bin it makes such nasty irritating sound. When resolution goes to 1920x1080 it's a bit better. Any idea why?

  Read the article

• creating a backup system with freenas

  - by masfenix

  We are currently in the process of opening a new accounting firm in the new year (actually moving from our previous location). I am looking for a cheap/free solution to back up our files (small, text files couple of kb). I was impressed with FreeNas and Windows Backup but I found out that Windows Backup only saves for a maximum of 2 years. The work machines will be running Windows 8 or Windows 7. There can be many work machines however we have only one to start with (ie, think of it as just one employee). I have an old core 2 duo with 2 gigs of ram that I can convert to a server if need be. I want the syncing to be done through LAN since the data is confidential and should never touch the outside world. So ideally, I would like the following scenario: A skydrive/dropbox like service to sync my client files over work machines and a central server. The "server" part should store history of files (i don't know how this will be done since the file will have the same name?). This isn't really necessary, but I can see it become useful. I am not familiar with RAID, so does any software RAID solution exist? I will most likely be buying 2 hard drives.

  Read the article

• Bad performance with Linux software RAID5 and LUKS encryption

  - by Philipp Wendler

  I have set up a Linux software RAID5 on three hard drives and want to encrypt it with cryptsetup/LUKS. My tests showed that the encryption leads to a massive performance decrease that I cannot explain. The RAID5 is able to write 187 MB/s [1] without encryption. With encryption on top of it, write speed is down to about 40 MB/s. The RAID has a chunk size of 512K and a write intent bitmap. I used -c aes-xts-plain -s 512 --align-payload=2048 as the parameters for cryptsetup luksFormat, so the payload should be aligned to 2048 blocks of 512 bytes (i.e., 1MB). cryptsetup luksDump shows a payload offset of 4096. So I think the alignment is correct and fits to the RAID chunk size. The CPU is not the bottleneck, as it has hardware support for AES (aesni_intel). If I write on another drive (an SSD with LVM) that is also encrypted, I do have a write speed of 150 MB/s. top shows that the CPU usage is indeed very low, only the RAID5 xor takes 14%. I also tried putting a filesystem (ext4) directly on the unencrypted RAID so see if the layering is problem. The filesystem decreases the performance a little bit as expected, but by far not that much (write speed varying, but 100 MB/s). Summary: Disks + RAID5: good Disks + RAID5 + ext4: good Disks + RAID5 + encryption: bad SSD + encryption + LVM + ext4: good The read performance is not affected by the encryption, it is 207 MB/s without and 205 MB/s with encryption (also showing that CPU power is not the problem). What can I do to improve the write performance of the encrypted RAID? [1] All speed measurements were done with several runs of dd if=/dev/zero of=DEV bs=100M count=100 (i.e., writing 10G in blocks of 100M). Edit: If this helps: I'm using Ubuntu 11.04 64bit with Linux 2.6.38. Edit2: The performance stays approximately the same if I pass a block size of 4KB, 1MB or 10MB to dd.

  Read the article

• keyboard intermittently stops working, even after reinstalling windows 7; possibly a Chrome issue?

  - by neverskipbreakfast

  My keyboard intermittently stops working. Sometimes a couple of keys will work, but usually none. Sometimes if I mash a couple of the ctrl+alt+windows type keys randomly for a bit, the keyboard will let me type one more letter before stopping again. Sometimes the keys will open a program menu, but usually not. I have even completely wiped my machine and reinstalled windows 7; the problem continues. Specs: Intel iMac (early 2006, 2.0GHz, 2MB RAM, 240GB HD) running ONLY Windows 7 Professional, 32-bit (NOT through boot camp) and using a USB keyboard (Saitek Eclipse II.) *Unplugging & reconnecting keyboard does NOT fix it. *Connecting a different keyboard does NOT fix it. That one won't work, either. *Drivers are up-to-date. Removing and reinstalling drivers does NOT fix it. *Restarting the computer does NOT fix it. In fact, when the Windows logon screen appears, they keyboard won't work, and neither will the icon to pull up the on-screen keyboard. Otherwise my mouse can click around just fine. I can only log onto a non-password protected account. *Generally, logging into as different Windows user fixes it. I can then log back on to my main user account and continue work for a few hours until it happens again. *Clearing my Chrome browsing data stopped the problem from recurring for a week or so. *I use Avira free antivirus software, and repeated scans turn up nothing fishy. *I have already REINSTALLED Windows 7 (not just a restore.) The problem returned after 2 days of use. The only thing I suspect is something in Google Chrome -- I used my google account to reload all my previous Chrome extensions, saved data, etc. (Chrome Extensions Installed: AdBlock, Better Google Tasks, DropBox, FB Photo Zoom, Google Mail Checker, StayFocusd.) Any ideas? Any at all?

  Read the article

• Hadoop initscript askes password

  - by Ramesh

  I have installed hadoop on my ubuntu 12.04 single node .I am trying to execute an init script to make the hadoop run on start up but it asks password every time i execute. #!/bin/sh ### BEGIN INIT INFO # Provides: hadoop services # Required-Start: $network # Required-Stop: $network # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Description: Hadoop services # Short-Description: Enable Hadoop services including hdfs ### END INIT INFO PATH=/usr/local/sbin:/usr/local/bin:/sbin:/bin:/usr/sbin:/usr/bin HADOOP_BIN=/home/naveen/softwares/hadoop-1.0.3/bin NAME=hadoop DESC=hadoop USER=naveen ROTATE_SUFFIX= test -x $HADOOP_BIN || exit 0 RETVAL=0 set -e cd / start_hadoop () { set +e su $USER -s /bin/sh -c $HADOOP_BIN/start-all.sh > /var/log/hadoop/startup_log case "$?" in 0) echo SUCCESS RETVAL=0 ;; 1) echo TIMEOUT - check /var/log/hadoop/startup_log RETVAL=1 ;; *) echo FAILED - check /var/log/hadoop/startup_log RETVAL=1 ;; esac set -e } stop_hadoop () { set +e if [ $RETVAL = 0 ] ; then su $USER -s /bin/sh -c $HADOOP_BIN/stop-all.sh > /var/log/hadoop/shutdown_log RETVAL=$? if [ $RETVAL != 0 ] ; then echo FAILED - check /var/log/hadoop/shutdown_log fi else echo No nodes running RETVAL=0 fi set -e } restart_hadoop() { stop_hadoop start_hadoop } case "$1" in start) echo -n "Starting $DESC: " start_hadoop echo "$NAME." ;; stop) echo -n "Stopping $DESC: " stop_hadoop echo "$NAME." ;; force-reload|restart) echo -n "Restarting $DESC: " restart_hadoop echo "$NAME." ;; *) echo "Usage: $0 {start|stop|restart|force-reload}" >&2 RETVAL=1 ;; esac exit $RETVAL Please tell me how to run hadoop without entering password.

  Read the article

• Vista won't boot. BSOD: Page fault in nonpaged area

  - by user31576

  Here's the story: I let Windows Update do the updates it wanted to do, then rebooted the computer. The updating process was taking time so I went away. When I came back, my computer was rebooting. It got as far as the Windows logo with the laoding bar. BSOD'd. Rebooted. And I'm stuck in this loop ever since. Looked up on the net, the "Page fault in nonpaged area" seems to be linked to faulty RAM or drivers. So I ran a memory test, it found no error. When I try in safe mode (with promt) I can see a list of drivers being loaded, then I get the same BSOD. I tried to repair using the Vista DVD, it says "nothing to repair". I tried to restore to a previous state, it says "no restore point found". So, my guess is, it's got something to do with the drivers. How can I identify the one causing the BSOD? If you have any other leads, What can I do? By the way, I'm writing from this very computer, running a linux distro I installed after the BSOD loop started. So i guess it's not an hardware issue. I have backed up important data, and will format and reinstall Windows if I must. But I'd like to avoid that. Thanks in advance for any help you can give me.

  Read the article

• Motherboard Dying? AHCI Drive Init and boot loop intermittent failure

  - by Adam Heath

  My computer is now intermittently failing to boot up. For the last couple of days, when I turn it on it hangs on "AHCI Drive Init...", and when powered off and on again, it booted up fine. Today, it did the same but failed in a few other ways too, seemingly at random: Hangs on "AHCI Drive Init..." Boot loop (after "AHCI Drive Init..." appears for a split second (no drives listed)) Black screen (after "AHCI Drive Init..." appears for a split second, a black screen with all fans still running) The interesting part is that the above is not affected by what drives are connected, or what to. I have tried both disks, each disk individually and no disks (along with trying the primary and secondary SATA controllers), none of this has any effect on what happens. After about 20+ attempts of different combinations, it suddenly decided it would boot up into Windows, and I hadn't touched anything for about 2 cycles. Motherboard: Gigabyte GA-870A-USB3 Processor: Amd Phoenom II x6 1090T RAM: 8GB Corsair 1600 Primary Disk: Plextor 128GB SSD Secondary Disk: Western Digital Black 1TB OS: Windows 8.1 Is this my motherboard dying? Or could something else be the cause? Thanks!

  Read the article

• DHCP Relay setup in ubuntu server

  - by jerichorivera

  I have a network appliance (QNO) that works as traffic load balancer and dhcp server. I would like to add a linux server in between the network appliance and the client computers. The linux server will be used to monitor bandwidth usage. My problem is I still want DHCP to be served by the network appliance so that load balancing will still work efficiently. We are afraid that if we setup the linux server as the DHCP server the network appliance will not be able to load balance the traffic if it only sees the linux server as a single client connecting to it. I've been searching all over for a tutorial on how to setup DHCP relay but have not found any. How do I setup DHCP relay on my linux server given there are two NICs attached to it, one connects the linux server to the network appliance and the other connects the linux server to the client computers. EDIT Router (DHCP) ---- [eth0] Linux Server (Relay agent) [eth1] ----- PC (network) Router IP is 192.168.0.100 eth0 is on DHCP eth1 is static 192.168.2.11 (if I need to change this I can) Tried to do dhcrelay -i eth1 192.168.0.100, but the PC was not getting any DHCP lease from the DHCP router. I might be missing something here.

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• Merely installing PHP5 causes my AWS Ubuntu server to die minutes later from a massive CPU spike

  - by Mark Amery

  I have an AWS server with Ubuntu 11.04 as the OS that is running an Apache2 webserver (incidentally Python-based and using Django). We recently needed to add support for php5 to let us use a third party PHP library (incidentally for serving minified versions of js and css files). However, for no reason any of us can discern, if we simply run sudo apt-get install php5 on the server, then the install appears to finish successfully but, without us taking any further action (including not yet running sudo apt-get install libapache2-mod-php5, which I think would be the next step for us if everything worked), or actually running any PHP scripts on the server, a few minutes later the server becomes impossible to connect to, and looking at the 'Monitoring' tab for the server in the EC2 Management Console reveals that a while after the installation, CPU usage spikes to 100% and stays there permanently (until we reboot the server from the AWS Console). After rebooting, the server also reliably dies within a few (between 0 and 10) minutes. We restored the server to a pre-PHP state from an AMI Image, observed that it was stable, and then tried installing PHP5 again and observed the server die in exactly the same way, so we're pretty much certain that installing PHP5 is what causes the symptoms. What on earth could be causing this behaviour, and how can we get PHP installed on the server without it dying?

  Read the article

• Server configration for our website [duplicate]

  - by Varun Varunesh

  This question already has an answer here: Can you help me with my capacity planning? 2 answers We are a start-up and 6 month back we have launched our beta version website. Now we are in a phase of building our website and web-services for the final product. This website will be based on PHP, Python, MySql database and with wamp server. Right now in the beta version we are using Azure VM for hosting, with configuration of 786MB RAM and Shared CPU. We have 200 avg users daily coming to our website. Now we are trying to increase the number of users from 200 to 1500 daily users. And I am thinking our server should have capability to handle at least 100 concurrent user. Also we have developed web-services for our mobile-apps. Which can also increase loads on the sever. So here are the question that takes me here, I am pretty much confused about whether to go with shared hosting or VM based hosting. If VM, then what configuration will be best for our requirement (as I discussed above) ? Currently our VM is a Windows based server and its very simple to manage, So other than cost factor why should I go for Linux based sever? What other factor should I keep in mind while choosing the server as per our requirement ?

  Read the article

• Performance tweaks and upgrades for VMWare Server 2

  - by sjohnston

  Our software department has a server running VMWare Server 2. We typically have 8-10 VMs running as test environments (Win XP and Server 08) for various versions of our software, and one VM that is used as a build server (Win XP). The host is running Server 2003 R2. It has 32GB RAM, 8 core Xeon 3.16GHz CPU, one disk for host OS and two raid disks for VMs. The majority of the time, this setup behaves very well and there are no complaints. Other times, the VMs can be very laggy. This is sometimes, but not always, correlated to heavy load on the build server. I'm a software developer, not an IT pro, but it seems to me that this machine should be beefy enough to handle this many VMs. Is this occasional performance hit likely just because we're hitting the limits of the hardware, or should I be looking for another culprit? From what I've read, I'm guessing if there's a bottleneck, it's probably disk I/O with all these VMs running off two disks (especially the build server). Would spreading the VMs over more disks, and/or switching to SSDs give us a significant performance boost? Other things I've read may increase performance: single virtual processor per VM removing/disabling unused virtual hardware preallocated disk space not using snapshots setting a reserved memory limit on the host and disabling VM memory swapping Can anyone confirm or deny if any of these improve performance? What other good tweaks have I missed?

  Read the article

• Move OS from RAID5 array to RAID 1 arrays

  - by Antoine

  I want to give a last boost to my old ProLiant ML350 G5 server which just needs to be reliable for a few more year only ! With a defined budget of about 1500$ (I do not have more), i plan to replace the CPU (+ adding a second one), the battery cache of my raid controller (E200i), double the RAM, and change all hard drives. I have 7 HDD (SAS 10krpm, 72Gb) + 1 spare in RAID5, and my system is all FULL (no empty tray, full disks). in my current RAID5 array, I have 2 partitions: - 1 OS partition, 20Gb - 1 data partition, 350 Gb I plan to replace these 8 disks with : - 2 x 300Gb SAS 15krpm in RAID 1 (= 1 partition for OS) - 2 x 2Tb SATA 7.2krpm in RAID 1 (= 1 partition for DATA) My biggest constraint is that I have only 01 day to upgrade my server. Therefore, I'm looking for cloning all my files (OS + data partition) to my new arrays, i.e : - the OS partition shall be cloned to the RAID1 "2x300Gb array" - the data partition shall be cloned to the RAID1 "2x2Tb array" My second problem is that I need to physically remove all the old hard drives before inserting the new ones. I'm running Windows Server 2003 R2, and even if MS support will expire soon, I cannot buy a new licence and spent time in configuration. Obviously, with 1500$, I cannot also buy a new server that I could start configuring from now ! Thought about ASR (NTBackup), but I have no floppy drive (and do not really want to invest in one !) Thought about a clonezilla clone, and read this interesting link : Windows Server 2003 - move C: partition to a new SAS disk , but i'm not so confident in using Clonezilla with RAID5. What should be the best option to quickly and easily (if possible!) "copy/paste" my OS (so no need to reinstall and reconfigure all) and DATA / programs / services, etc... ? Thanks for your comments

  Read the article

• How to handle files that don't need version control in mercurial

  - by richardh

  I am new to mercurial, and for the most part do LaTeX reports and statistical calculations in R using .csv and/or .sqlite files. Re LaTeX, all I really care is the .tex file. Re R, I don't need version control on the .csv or .sqlite files because they are static. When I do 'hg add' for a repo with a .csv and/or .sqlite file, I get a warning like: rev2.sqlite: up to 3070 MB of RAM may be required to manage this file (use 'hg revert rev2.sqlite' to cancel pending addition) So I revert and subsequently use adds like hg add -X *.sqlite. I guess I really have two questions: (1) Should I ignore these warnings? Because these large files are static, can I just add to the repo knowing that the diff files will always be empty and not worry about wasted resources? (2) If I should keep excluding these files from the repo, is there away that I can fix this option? I.E., add to my .hgrc file something that always appends an option like -I *.tex -I *.R to my 'hg add' commands? Thanks!

  Read the article

• Startup script for Red5 on Ubuntu 9.04

  - by user49249

  I am creating startup script for Red5 on Ubuntu. Red5 is installed in /opt/red5 Following is a working script on a CentOS Box on which Red5 is running [code] ==========Start init script ========== #!/bin/sh PROG=red5 RED5_HOME=/opt/red5/dist DAEMON=$RED5_HOME/$PROG.sh PIDFILE=/var/run/$PROG.pid # Source function library . /etc/rc.d/init.d/functions [ -r /etc/sysconfig/red5 ] && . /etc/sysconfig/red5 RETVAL=0 case "$1" in start) echo -n $"Starting $PROG: " cd $RED5_HOME $DAEMON >/dev/null 2>/dev/null & RETVAL=$? if [ $RETVAL -eq 0 ]; then echo $! > $PIDFILE touch /var/lock/subsys/$PROG fi [ $RETVAL -eq 0 ] && success $"$PROG startup" || failure $"$PROG startup" echo ;; stop) echo -n $"Shutting down $PROG: " killproc -p $PIDFILE RETVAL=$? echo [ $RETVAL -eq 0 ] && rm -f /var/lock/subsys/$PROG ;; restart) $0 stop $0 start ;; status) status $PROG -p $PIDFILE RETVAL=$? ;; *) echo $"Usage: $0 {start|stop|restart|status}" RETVAL=1 esac exit $RETVAL [/code] What do I need to replace for Ubuntu in the above script. My Red5 is in /opt/red5/ and to start it manually I always do /opt/red5/dist/red5.sh from Ubuntu As I did not find rc.d/functions on Ubuntu on my laptop also /etc/init.d/functions I did not existed. I would like to be able to use them with service as Red hat distributions do. I checked /lib/lsb/init-functions.

  Read the article

• Reducing both pagfile.sys and hiberfil.sys in Windows 7

  - by greenber

  I recently used Defraggler to consolidate my free space areas on my D: drive preparatory to using Disk Manager to break my drive into two areas, one as my "data area" for Windows 7 (normally on my C: drive) and to experiment around with Windows 8. The Defraggler program works so well I ran it on my C: drive and I ended up with a lot of free space both on my C: drive and my D: drive. I was very happy. And then I woke up the next day and I've got virtually no free space left, something like 8 MB on my C: drive and about 3 GB on my D: drive. I then ran Wintree (which gives a nifty graphical representation of disk usage) and found I had a large page file and a large hiberfil. So I temporarily turned off hibernate and reduced the page file size to 2000megabytes and then rebooted so that both would take effect. It had no effect on the C: drive or the D: drive. That makes no sense to me. What caused the free space on each drive to disappear, why doesn't the page file size being reduced and the hibernate file being turned off free up disk space to either the C: or the D: drive? Would it make sense to delete the two files in question and, if so, how do I go about doing that? Safe mode? Thanks. Ross

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

• Computer Won't Boot Properly, unless in safe mode?

  - by Mr_CryptoPrime

  I bought a computer today and booted it up, but when I did I only got a blank screen. I checked to make sure it wasn't the monitor by connecting it to my old computer...it worked. I then tried connecting my monitor to both DVI ports and found that the bottom one did work. However, now it just boots up and says "loading windows" and then when the login screen is suppose to come up the screen just goes blank and monitor says "no input, check cord" (or something like that). I tried reinstalling windows and then I was able to log on normally. I used the CD's and reinstalled all the drivers, then rebooted...now I am stuck right back where I started. I tried taking out the RAM and inserting into different slots, that didn't fix anything. I was able to boot up into windows using safe-mode. I suspected that my ATI Radeon 6950 was the issue and downloaded the drivers, but I can't install them on safe-mode. Someone said to install C++ distr. and I tried doing that to fix driver installation problem of "failed to load detection driver" but it wouldn't let me do that either. Please someone help me, I don't want to have to deal with the evil redtape of sending it back to get a replacement! My computer: -Content--text-_-"http://www.newegg.com/Product/Product.aspx?Item=N82E16883229236&nm_mc=TEMC-RMA-Approvel&cm_mmc=TEMC-RMA-Approvel--Content--text-_- Driver detection problem: http://www.hardwareheaven.com/hardwareheaven-tools-discussion/174912-failed-load-detection-driver-installation-error.html Driver download page: http://sites.amd.com/us/game/downloads/Pages/radeon_win7-64.aspx#1 I am using windows 7. Thanks again.

  Read the article

< Previous Page | 322 323 324 325 326 327 328 329 330 331 332 333  | Next Page >