Search Results

Search found 9332 results on 374 pages for 'an original alias'.

Page 33/374 | < Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >

• How to connect SAN from CentOS through two iSCSI Targets

  - by garconcn

  I had asked the similar question before. This time I want to use subnet for two iSCSI Targets, hence I start a new question. I have an old Promise VTrak M500i SAN Server. It comes with 2 iSCSI ports. I want to connect to two LUNs on the SAN server through two separate Targets from CentOS 5.7 64bits server. My network setup is as follows: CentOS server: Management network - 192.168.1.1 Storage network 1 - 192.168.5.2 Storage network 2 - 192.168.6.2 Promise SAN server: Management network - 192.168.1.2 iSCSI Port 1 - 192.168.5.1 iSCSI Port 2 - 192.168.6.1 I have two Logical Drives on this SAN and they are mapped as follows: Index Initiator Name LUN Mapping 0 iqn.2011-11:backup (LD0,0) 1 iqn.2011-11:template (LD1,1) Basically, I want the traffic to iqn.2011-11:backup LUN 0 through 192.168.5.1 network the traffic to iqn.2011-11:template LUN 1 through 192.168.6.1 network I don't use MPIO, just want to separate the traffic to avoid traffic jam. How do I achieve this? I am new to SAN stuff, please explain as much detail as you can. Thank you. The following are what I am doing now. After mapping the LUN to my pre-defined Initiators, the CentOS server can discover both Targets. [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.5.1 192.168.5.1:3260,1 iscsi-1 192.168.6.1:3260,2 iscsi-1 [root@centos ~]# iscsiadm -m discovery -t sendtargets -p 192.168.6.1 192.168.6.1:3260,2 iscsi-1 192.168.5.1:3260,1 iscsi-1 [root@centos ~]# /etc/init.d/iscsi start iscsid is stopped Starting iSCSI daemon: [ OK ] [ OK ] Setting up iSCSI targets: Logging in to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] Logging in to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] Login to [iface: default, target: iscsi-1, portal: 192.168.6.1,3260] successful. Login to [iface: default, target: iscsi-1, portal: 192.168.5.1,3260] successful. [ OK ] [root@centos ~]# iscsiadm -m session tcp: [1] 192.168.6.1:3260,2 iscsi-1 tcp: [2] 192.168.5.1:3260,1 iscsi-1 When I check the LUN mapping on the SAN server for the two Logical Drives, both LUNs are connected through Port0-192.168.5.2 with the Initiator defined in CentOS. Assigned Initiator List: Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.centos centos.mydomain.com Port1-192.168.5.2 1 I assume the following is what I want: Initiator Name Alias IP Address LUN iqn.2011-11.backup centos.mydomain.com Port0-192.168.5.2 0 Initiator Name Alias IP Address LUN iqn.2011-11.template centos.mydomain.com Port0-192.168.6.2 1

  Read the article

• virsh XML interface allocation

  - by Kaushik Koneru

  I am trying to launch VM using a XML. This VM will be having 5 interfaces each connected to certain bridge. Issue here is allocation of these interfaces is random. My XML <interface type='bridge'> <mac address='52:54:00:9f:14:b3'/> <source bridge='br0'/> <target dev='vnet1'/> <model type='e1000'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:b4'/> <source bridge='br1'/> <target dev='vnet2'/> <model type='e1000'/> <alias name='net1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x10' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:b5'/> <source bridge='br2'/> <target dev='vnet2'/> <model type='e1000'/> <alias name='net3'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x12' function='0x0'/> </interface> <interface type='bridge'> <mac address='52:54:00:9f:14:c4'/> <source bridge='br3'/> <target dev='vnet3'/> <model type='e1000'/> <alias name='net4'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x18' function='0x0'/> </interface> Allocation of interfaces are random mean e th6 will be connected to br3 ; eth7 -- br4 eth8 -- br2 eth9 -- br0. Is there any way to make it static?? At the same time is there anyway of assigning IP Address to these eth interfaces through XML file itself??

  Read the article

• Website occasionally unavailable - DNS problem

  - by Kamil

  Hi, I have a problem with my website. I have webmin and virualmin. I have one domain as alias, and this alias sometimes is unavailable for several minutes. It's probably DNS problem because chrome shows 105 (net::ERR_NAME_NOT_RESOLVED). How can I troubleshoot this problem?

  Read the article

• How can I set automatically update the title in an xterm running screen?

  - by Nathan Fellman

  This is a bit of a followup to this question. I have the following in my .cshrc: alias res_t 'xtset -t %h:%d "(%u:%g)" %e' # reset titlebar res_t # reset title right now alias precmd res_t And this works fine! However, when I run screen I see that the title doesn't get updated with the current directory. How can I make screen update the xterm title? Note: I am working in tcsh.

  Read the article

• iPod Nano 5th gen Album Artwork

  - by Wesley Caretto

  I am an album artwork fan. I just got all of these brand new alternate artwork covers for my albums and singles. Eventually, i got bored of them, and i wanted the original ones back. So i got on iTunes, and changed the original album covers to the primary covers. I synced my ipod, but it still showed the new covers on it, not the originals. I figured a temporary way to fix it, by deleting the new covers i got, making the originals the default. There has to be an easier way, though. p.s. this also works in vice-versa. I will add the new covers, but before i exit, i change the primary cover to the original. When i change it back to the new one, my iPod will still only show the original Thanks for helping!

  Read the article

• Checking the configuration of two systems to determine changes

  - by None

  We are standing up a replicant data center at work and need to ensure that the new data center is configured (nearly) identically to the original. The new data center will be differently addressed and named than the original and will have differing user accounts, but all the COTS, patches, and configurations should be the same. We would normally ghost the original servers and install those images onto the new machines, however, we have a few problematic pieces of COTS that require we install them outside of an image due to how they capture the setup of the network during their installation and maintain it within their configuration information (in some cases storing it in various databases). We have tried multiple times and this piece of COTS cannot be captured within a ghost image unless the destination machine will have an identical network setup (all the same IPs, hostnames, user accounts, etc across the entire network) as the original. In truth, it is the setup of these special COTS that I want to audit the most because they are difficult to install and configure in the first place. In light of the fact that we can’t simply ghost, I’m trying to find a reasonable manner to audit the new data center and check to see if it is setup like the original (some sort of system wide configuration audit or integrity check). I’m considering using something like Tripwire for Servers to capture the configuration on the source machines and then run an audit on the destination machines. I understand that it will still show some differences due to the minor config changes, but I’m hoping that it will eliminate the majority of the work. Here are some of the constraints I’m working under: Data center is comprised of multiple Windows and Linux machines of differing versions (about 20 total) I absolutely cannot ghost or snap any other type of image of these machines … at least not in their final configuration I want to audit the final configuration to ensure all of the COTS, patches, configurations, etc are installed and setup properly (as compared to the original data center) I would rather not install any additional tools on these machines … I’d much rather run it from a standalone machine or off a DVD Price of tools is important but not an impossible burden, however, getting a solution soon is important (I can’t take the time to roll my own tools to do this) For the COTS that stores the network information, I don’t know all of the places it stores the network information … so it would be unlikely I could find a way in the near future to adjust its setup after the installation has occurred Anyone have any thoughts or alternate approaches? Can anyone recommend tools that would be usable for system wide configuration audits?

  Read the article

• Web application/ site service (like Google App Engine) for PHP/ MySQL and Postgres

  - by Simon

  I would like to find a service similar to Google App Engine for PHP/ MySQL/ Postgres sites/ applications. We host two different types of site. i). PHP/ Mysql/ Zend Framework <VirtualHost *:80> DocumentRoot "/home/websites/website.com/public" ServerName website.com # This should be omitted in the production environment SetEnv APPLICATION_ENV development <Directory "/home/websites/website.com/public"> Options Indexes MultiViews FollowSymLinks AllowOverride All Order allow,deny Allow from all RewriteEngine On RewriteCond %{REQUEST_FILENAME} -s [OR] RewriteCond %{REQUEST_FILENAME} -l [OR] RewriteCond %{REQUEST_FILENAME} -d RewriteRule ^.*$ - [NC,L] RewriteRule ^.*$ index.php [NC,L] </Directory> </VirtualHost> ii). Matrix CMS - PHP/ Postgres + loads of pear classes <VirtualHost *:80> ServerName server.example.com DocumentRoot /home/websites/mysource_matrix/core/web Options -Indexes FollowSymLinks <Directory /home/websites/mysource_matrix> Order deny,allow Deny from all </Directory> <DirectoryMatch "^/home/websites/mysource_matrix/(core/(web|lib)|data/public|fudge)"> Order allow,deny Allow from all </DirectoryMatch> <DirectoryMatch "^/home/websites/mysource_matrix/data/public/assets"> php_flag engine off </DirectoryMatch> <FilesMatch "\.inc$"> Order allow,deny Deny from all </FilesMatch> <LocationMatch "/(CVS|\.FFV)/"> Order allow,deny Deny from all </LocationMatch> Alias /__fudge /home/websites/mysource_matrix/fudge Alias /__data /home/websites/mysource_matrix/data/public Alias /__lib /home/websites/mysource_matrix/core/lib Alias / /home/websites/mysource_matrix/core/web/index.php/ </VirtualHost> My key requirements are: I don't want to worry/ know/ care about the server/ infrastructure Secure/ up to date software/ os Good monitoring Automatic scalability SLA I apologise for the length of the question. In short all I want to do is i). create vhost, ii). create db iii). install app/ site iv). relax. Thanks. Edit: I include the Matrix vhost because that is the only complication that I cannot really do via a .htaccess file.

  Read the article

• Piping Mail with Exim: Only Works Locally

  - by John

  Whenever I send an email to my catchall alias via SSH (i.e., locally), Exim successfully pipes the e-mail to a PHP script, as I told it to do. However, when I try to send an e-mail to my catchall alias via my e-mail client (i.e., remotely), Exim won't pipe the e-mail. Any ideas?

  Read the article

• HP Server Automation - agent misreporting hostname

  - by warren

  I've been using HP Server Automation for some time, but have noticed an interesting issue I'm hoping the SF community has seen / knows a workaround to. When the management agent on Solaris or RHEL (only platforms I've noticed it on) reports the hostname of the managed server, it does not return the value of hostname, it returns the first alias to that entry in /etc/hosts. Any ideas on how to get around that? Other than editing /etc/hosts so the alias is at the end of the line instead of the front?

  Read the article

• Win 7 Home Premium 64 bit running Cobian Backup 11 (Gravity)

  - by Andrew

  I'm really enjoying Cobian 11, but am fairly new to it. My question is this. I back up a pretty large folder on a regular basis. I started off by doing a Full backup, and have followed that monthly using differential backups. I was told that, to restore my computer after a crash, I need to copy back the original full backup AND copy back the latest differential over the full. That's fine. However, over the months there are quite a few large differential backups dated between the original Full one and the latest differential one. To free space on my backup HD, can I every now and then delete the differential backups that lie between the original Full and the latest differential, and just leave the original Full and the latest differential backup on the HD?

  Read the article

• What Triggers a syncronization between Exchange 2007 Mail Store and Edge Servers?

  - by BillN

  We are using Exchange 2007 for our mail. In our configuration, we need to add an alias to each users mailbox. When we do, the Edge server, another Exchange 2007 box, will reject the alias with a User Unknown error until the next morning. I seem to recall that in Exchange 2003, you could force an update from the Management console, but I can not find a way in 2007. It is obvious that a sync job is scheduled to run each night, but I cannot find it.

  Read the article

• What is good usage scenario for Rackspace Cloud Files CDN (powered by AKAMAI) [closed]

  - by Andrew Smith

  I have just setup my website as static page via Rackspace CDN / Akamai. www.example.co.uk is an alias for d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com. d9771e6f24423091aebc-345678991111238fabcdef6114258d0e1.r61.cf3.rackcdn.com is an alias for a61.rackcdn.com. a61.rackcdn.com is an alias for a61.rackcdn.com.mdc.edgesuite.net. a61.rackcdn.com.mdc.edgesuite.net is an alias for a63.dscg10.akamai.net. a63.dscg10.akamai.net has address 63.166.98.41 a63.dscg10.akamai.net has address 63.166.98.40 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ecb9 a63.dscg10.akamai.net has IPv6 address 2001:428:4c02::cda8:ed09 The HTTP header: HTTP/1.0 200 OK Last-Modified: Fri, 19 Oct 2012 23:27:41 GMT ETag: fdf9e14b77def799e09e8ce815a521da X-Timestamp: 1350689261.23382 Content-Type: text/html X-Trans-Id: tx457979be3bd746c2b4e5403a1189cdbc Cache-Control: public, max-age=900 Expires: Sat, 27 Oct 2012 22:18:56 GMT Date: Sat, 27 Oct 2012 22:03:56 GMT Content-Length: 7124 Connection: keep-alive I am wondering, if it's really the fastest solution to power the website? By investigating it thru http://www.just-ping.com/ it seems, that from many places the ping is very high, and during quick investigation I found that they use GeoIP to resolve addresses based on WHOIS, which is not accurate and because of that from many places the ping is above 300ms (for example, if ISP is in balgladore and request is routed to bangladore even if it's 300ms, for period of 1 month), while by just using Amazon Web Services and Route 53 Anycast DNS servers and only 4 EC2 instances it seems that for example India is always below 100ms, while using Akamai it goes above 300ms in some cases, and this is because Route 53 is using BGP. By quickly checking the Akamai, it seems that they are not getting feedback from the traffic - the high ping stays constant even if I keep downloading large files and videos, which is opposite to what they say on their website. They state, that they optimize the performance by taking feedback from the requests, while it seems they just use GeoIP with per City resolution (which are mostly big cities). Because of this, AWS with Route 53 / Anycast DNS seems to be much more reliable, as well EdgeCast which is using BGP, but I dont know how much does it cost to deploy static website. Actually, I dont know if EdgeCast is not a lie, because from isolated places there are many errors - so their performance is at the cost of quality of delivery, because of BGP switching the routes during transfer of large files. So I was wondering, what is really Akamai good for, because they dont seem to pose any strength in any field in what I do understand now, except they offer some software based WAF on their website, but what I really care about is the core distribiution, so the question is? Is really Akamai good for Videos? For static websites? ??? I found so far AWS most usable with most consistent ping and stable transfers.

  Read the article

• How can I automatically update the title in an xterm running screen?

  - by Nathan Fellman

  This is a bit of a followup to this question. I'm working in tcsh within GNU screen in an xterm. I have the following in my .cshrc: alias res_t 'xtset -t %h:%d "(%u:%g)" %e' # reset titlebar res_t # reset title right now alias precmd res_t And this works fine! However, when I run screen I see that the title doesn't get updated with the current directory. How can I make screen update the xterm title?

  Read the article

• bash aliases equivalent for powershell?

  - by Santosh Kumar

  By default my Windows PowerShell starts in C:\Users\Santosh, my XAMPP installation is in D:\ so the htdocs folder is located at D:\xampp\htdocs. If I have to edit something in htdocs folder then I have to type full cd D:\xampp\htdocs\ (autocompletion is not so kind) then edit that file. If this PowerShell were a Bash I would do this in .bash_aliases file: alias htdocs='cd D:\xampp\htdocs' Is it possible to maintain Bash aliases like file and alias any command in PowerShell?

  Read the article

• Accidentally broke/remapped git command line command

  - by Kevin Teh

  I think I accidentally remapped my git command to automatically include the subcommand credential-osxkeychain on the command line while trying to install a git credential-helper. When I enter $git it now displays Usage: git credential-osxkeychain <get|store|erase> How can I fix it? Entering $alias returns alias rvm-restart='rvm_reload_flag=1 source '\''/Users/teh/.rvm/scripts/rvm'\''' Entering $which git returns /usr/bin/git I think the problem may have began when I entered a command to move git-credential-osxkeychain into /usr/bin/git instead of /usr/bin/

  Read the article

• Configure bash_profile for one single terminal emulator

  - by Hugo

  I'm using a new terminal emulator. Terminology is the E17 default terminal, and it have a great command, $ tyls with is a "graphical" $ ls I want to create an alias just for this terminal, because the command "tyls" don't make sense to konsole, rxvt or other terminals. I'm thinking in some kind of "if" in ~/.bash_profile to test if I'm on terminology and then run the following command: alias ls="tyls" But how can I test if I'm in terminology but not xterm? Can someone help me? Thanks!

  Read the article

• How do I restore to a delta file (disk) on Vmware ESXi

  - by Oscar

  Using VMware Server ESXi (freebie version) I have a Virtual Machine (win 2k3 r2 server). When I first provisioned it I took a snapshot of it. I recently tried to clone the primary drive using my standard hardware-based method to grow a windows disk. (using knoppix, clone drive to a new drive, make it bootable, then I intended to extend the partition via diskpart from within windows). This process failed; I tried setting the cloned drive (via the vmware gui) to replace the original drive, boot and be done. This didn't work out so well. The machine never booted. I checked the boot order, the disk location and all the basics I usually do. As a failsafe, I then tried changing all the settings back so the machine would boot to the original drive and I could figure out (as I eventually did) a better way of growing the disk. However when I powered on the machine with the original drive, it reverted back to that initial snapshot I created; It lost all the changes since. I looked in the file system and found a few files, I think the keyfile here is one named "delta" and I'm assuming that's the disk I want, but I can't find a way to have the Virtual Machine actually use that drive/file. It isn't available to add when I go to add an existing drive. Do I need to somehow commit that delta to the original drive and then boot from it again? Can you point me in the right direction? I've since discovered the proper way of growing drives using "vmkfstools" but I need to get back to the original state of the machine to try this out. Any help would be greatly appreciated.

  Read the article

• How to prevent stretching, blurring and pixelating of embedded logos in VirtualDub?

  - by NoCanDo

  Howdy, take a look at this please http://www.youtube.com/watch?v=te-HVN8y_QE&hd=1 . Notice the embedded "logo" in the upper left corner? How blurry and pixelated it is? This is the original image: http://i.imagehost.org/0148/movie_watermark.png ! The stretching, blurring, pixelating etc. most likely comes from resizing the original video from 1920x1200 to 1280x720 and encoding it with h.264. Can anyone tell me how I can prevent the blurring, unsharpening and pixelating and retain their original quality? How do I exclude the logo from the whole encoding process and just slap it there in its original format and form?

  Read the article

• ~/.profile does not run on startup

  - by pocoa

  I want to run some scripts at system startup, so in ~/.profile file, I've added: WORKSPACE="~/Development/workspace" alias workspace="cd $WORKSPACE" So I want this "workspace" alias to be available after the startup. Maybe it's not the right place to define these variables.

  Read the article

• Are these three brand new sticks of RAM really dead?

  - by David Brown

  I'm working on a Dell Dimension 4700 desktop for a friend. It came with 512MB of DDR2 RAM (two sticks of 256MB). One morning, it started blue screening on startup with no helpful error messages. It refused to boot into any form of Windows installation, including Safe Mode, original recovery disk, and my custom Windows PE disk. It did boot into the Ultimate Boot CD, so I ran memtest86, which reported errors everywhere. I removed one stick of RAM and the system booted up just fine. I moved the remaining stick into each slot and the system continued to operate normally, so I came to the conclusion that the stick that I removed was dead. I ordered an exact replacement, along with 2 more sticks of 256MB DDR2 (again, exactly the same as the original), bringing the total system memory to 1GB. Upon installing the three brand new sticks, the system blue screened again, this time stating that win32k.sys attempted to write to read-only memory. I inserted my custom Windows PE disk in order to get a better look at the memory dump with BlueScreenView, but it refused to boot and produced another blue screen, but without an error message. I removed each new stick one-by-one, restarting each time. It continued to blue screen until I was left with only the original stick. I then tried inserting the new sticks in various different orders, but this only produced more blue screens. I reinserted all three sticks (along with the original) and ran memtest86 again, which reported errors all over the place. So, now I'm right back where I started. I don't think it could be the slots themselves, because I can plug the original stick into any slot and it works just fine. System setup reports each stick correctly and shows the total as 1GB, however. It just seems strange to me that all three brand new sticks of RAM could be dead on arrival. Is there something I missed? Or should I just go ahead and RMA them?

  Read the article

• How do I specify Windows file paths in nginx

  - by Vasil

  I'm using the official windows version of nginx. I want to specify the windows equivalent of this configuration location /static/ { alias /home/user/staticfiles/; } How do I specify windows file paths in the alias directive? Is this even possible?

  Read the article

• Serving protected files using Nginx's X-Accel-Redirect header

  - by andybak

  I'm trying to serve protected files using this directive in my nginx.conf: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/secure/; } I'm passing in paths in the form: "/myfile.doc" and the file's path would be: /home/ldr/webapps/nginx/app/secure/myfile.doc I just get 404's when I access "http: //myserver/secure/myfile.doc" (space inserted after http to stop ServerFault converting it to a link) I've tried taking the trailing / off the location directive and that makes no difference. Two questions: How do I fix it! How can I debug problems like this myself? How can I get Nginx to report which path it's looking for? error.log shows nothing and access.log just tells me which url is being requested - this is the bit I already know! It's no fun trying things randomly without any feedback. Here's my entire nginx.conf: daemon off; worker_processes 2; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server { listen 21534; server_name my.server.com; client_max_body_size 5m; location /media/ { alias /home/ldr/webapps/nginx/app/media/; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; fastcgi_pass unix:/home/ldr/webapps/nginx/app/myproject/django.sock; fastcgi_pass_header Authorization; fastcgi_hide_header X-Accel-Redirect; fastcgi_hide_header X-Sendfile; fastcgi_intercept_errors off; include fastcgi_params; } location /secure { internal; alias /home/ldr/webapps/nginx/app/secure/; } } } EDIT: I'm trying some of the suggestions here So I've tried: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/; } both with and without the trailing slash on location. I've also tried moving this block before the "location /" directive. The page I linked to has ^~ after 'location' giving: location ^~ /secure/ { ...etc... Not sure what that signifies but it didn't work either!

  Read the article

• XDCAM HD 422 frame setting

  - by sebastian

  I have a question that you can hopefully answer me. I am trying to write a ffmpeg script that transcodes my clips in XDCAM HD 422 1080p24, and it works fine as long as the original file has 24 fps, but is there a way that I can set an option which says "even if the original file has 25 fps I will transcode it in 24 fps". I have tried it, like I said it works fine as long as the original clip has 24 frames, but as soon as the original clip has another framerate, he can not convert it to 24 frames. I have tried using -r 24 which normally settles the framerate, but here it doesn't work. I am using the -vtag xd5c

  Read the article

• PC won't boot, even into bios

  - by divided

  Here's the deal: I cleaned a hard drive of some viruses (externally) and put it back into the original pc. This hard drive will boot in any other pc except the original pc. When I try other hard drives in the original pc, they are able to boot. The drive has Windows XP. What is the problem? How can I get this hard drive to work properly? The original hard drive works in other PCs. The PC boots with other hard drives acting as the master. If I boot with no hard drive, I still can't get into the BIOS These are all IDE hard drives The PC doesn't beep, it just boots into a black screen with a cursor blinking in the upper left of the screen

  Read the article

• Javascript autotab function not working on iPad or iPhone [migrated]

  - by freddy6

  I have this this piece of html code: <form name="postcode" method="post" onsubmit="return OnSubmitForm();"> <input class="postcode" maxlength="1" size="1" name="c" onKeyup="autotab(this, document.postcode.o)" /> <input class="postcode" maxlength="1" size="1" name="o" onKeyup="autotab(this, document.postcode.d)" /> <input class="postcode" maxlength="1" size="1" name="d" onKeyup="autotab(this, document.postcode.e)" /> <input class="postcode" maxlength="1" size="1" name="e" /> <br /> </form> which uses this javascript: <script> /* Auto tabbing script- By JavaScriptKit.com http://www.javascriptkit.com This credit MUST stay intact for use */ function autotab(original,destination){ if (original.getAttribute&&original.value.length==original.getAttribute("maxlength")) destination.focus() } </script><script src="http://ajax.googleapis.com/ajax/libs/jquery/1.4/jquery.min.js" type="text/javascript"></script> <script src="js/scripts.js" type="text/javascript"></script> <script type="text/javascript"> function OnSubmitForm() { if(document.postcode.operation[0].checked == true) { document.postcode.action ="plans.php"; } else if(document.postcode.operation[1].checked == true) { document.postcode.action ="plans_gas.php"; } else if(document.postcode.operation[2].checked == true) { document.postcode.action ="plans_duel.php"; } return true; } </script> As soon a you enter in one character into one of the text boxes it automatically tabs across the the next text box. This works fine on a pc or mac and on safari and also in all other browsers. But when viewing the webpage on an iPad or iPhone (using safari) the auto tabbing function does not work. Any ideas on how to make the auto tab work on these mobile devices?

  Read the article

< Previous Page | 29 30 31 32 33 34 35 36 37 38 39 40  | Next Page >