Search Results

Search found 30486 results on 1220 pages for 'network level auth'.

Page 330/1220 | < Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >

  • [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

    - by Beco
    I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

    Read the article

  • URL Rewrite – Protocol (http/https) in the Action

    - by OWScott
    IIS URL Rewrite supports server variables for pretty much every part of the URL and http header. However, there is one commonly used server variable that isn’t readily available.  That’s the protocol—HTTP or HTTPS. You can easily check if a page request uses HTTP or HTTPS, but that only works in the conditions part of the rule.  There isn’t a variable available to dynamically set the protocol in the action part of the rule.  What I wish is that there would be a variable like {HTTP_PROTOCOL} which would have a value of ‘HTTP’ or ‘HTTPS’.  There is a server variable called {HTTPS}, but the values of ‘on’ and ‘off’ aren’t practical in the action.  You can also use {SERVER_PORT} or {SERVER_PORT_SECURE}, but again, they aren’t useful in the action. Let me illustrate.  The following rule will redirect traffic for http(s)://localtest.me/ to http://www.localtest.me/. <rule name="Redirect to www"> <match url="(.*)" /> <conditions> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> </conditions> <action type="Redirect" url="http://www.localtest.me/{R:1}" /> </rule> The problem is that it forces the request to HTTP even if the original request was for HTTPS. Interestingly enough, I planned to blog about this topic this week when I noticed in my twitter feed yesterday that Jeff Graves, a former colleague of mine, just wrote an excellent blog post about this very topic.  He beat me to the punch by just a couple days.  However, I figured I would still write my blog post on this topic.  While his solution is a excellent one, I personally handle this another way most of the time.  Plus, it’s a commonly asked question that isn’t documented well enough on the web yet, so having another article on the web won’t hurt. I can think of four different ways to handle this, and depending on your situation you may lean towards any of the four.  Don’t let the choices overwhelm you though.  Let’s keep it simple, Option 1 is what I use most of the time, Option 2 is what Jeff proposed and is the safest option, and Option 3 and Option 4 need only be considered if you have a more unique situation.  All four options will work for most situations. Option 1 – CACHE_URL, single rule There is a server variable that has the protocol in it; {CACHE_URL}.  This server variable contains the entire URL string (e.g. http://www.localtest.me:80/info.aspx?id=5)  All we need to do is extract the HTTP or HTTPS and we’ll be set. This tends to be my preferred way to handle this situation. Indeed, Jeff did briefly mention this in his blog post: … you could use a condition on the CACHE_URL variable and a back reference in the rewritten URL. The problem there is that you then need to match all of the conditions which could be a problem if your rule depends on a logical “or” match for conditions. Thus the problem.  If you have multiple conditions set to “Match Any” rather than “Match All” then this option won’t work.  However, I find that 95% of all rules that I write use “Match All” and therefore, being the lazy administrator that I am I like this simple solution that only requires adding a single condition to a rule.  The caveat is that if you use “Match Any” then you must consider one of the next two options. Enough with the preamble.  Here’s how it works.  Add a condition that checks for {CACHE_URL} with a pattern of “^(.+)://” like so: How you have a back-reference to the part before the ://, which is our treasured HTTP or HTTPS.  In URL Rewrite 2.0 or greater you can check the “Track capture groups across conditions”, make that condition the first condition, and you have yourself a back-reference of {C:1}. The “Redirect to www” example with support for maintaining the protocol, will become: <rule name="Redirect to www" stopProcessing="true"> <match url="(.*)" /> <conditions trackAllCaptures="true"> <add input="{CACHE_URL}" pattern="^(.+)://" /> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> </conditions> <action type="Redirect" url="{C:1}://www.localtest.me/{R:1}" /> </rule> It’s not as easy as it would be if Microsoft gave us a built-in {HTTP_PROTOCOL} variable, but it’s pretty close. I also like this option since I often create rule examples for other people and this type of rule is portable since it’s self-contained within a single rule. Option 2 – Using a Rewrite Map For a safer rule that works for both “Match Any” and “Match All” situations, you can use the Rewrite Map solution that Jeff proposed.  It’s a perfectly good solution with the only drawback being the ever so slight extra effort to set it up since you need to create a rewrite map before you create the rule.  In other words, if you choose to use this as your sole method of handling the protocol, you’ll be safe. After you create a Rewrite Map called MapProtocol, you can use “{MapProtocol:{HTTPS}}” for the protocol within any rule action.  Following is an example using a Rewrite Map. <rewrite> <rules> <rule name="Redirect to www" stopProcessing="true"> <match url="(.*)" /> <conditions trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> </conditions> <action type="Redirect" url="{MapProtocol:{HTTPS}}://www.localtest.me/{R:1}" /> </rule> </rules> <rewriteMaps> <rewriteMap name="MapProtocol"> <add key="on" value="https" /> <add key="off" value="http" /> </rewriteMap> </rewriteMaps> </rewrite> Option 3 – CACHE_URL, Multi-rule If you have many rules that will use the protocol, you can create your own server variable which can be used in subsequent rules. This option is no easier to set up than Option 2 above, but you can use it if you prefer the easier to remember syntax of {HTTP_PROTOCOL} vs. {MapProtocol:{HTTPS}}. The potential issue with this rule is that if you don’t have access to the server level (e.g. in a shared environment) then you cannot set server variables without permission. First, create a rule and place it at the top of the set of rules.  You can create this at the server, site or subfolder level.  However, if you create it at the site or subfolder level then the HTTP_PROTOCOL server variable needs to be approved at the server level.  This can be achieved in IIS Manager by navigating to URL Rewrite at the server level, clicking on “View Server Variables” from the Actions pane, and added HTTP_PROTOCOL. If you create the rule at the server level then this step is not necessary.  Following is an example of the first rule to create the HTTP_PROTOCOL and then a rule that uses it.  The Create HTTP_PROTOCOL rule only needs to be created once on the server. <rule name="Create HTTP_PROTOCOL"> <match url=".*" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{CACHE_URL}" pattern="^(.+)://" /> </conditions> <serverVariables> <set name="HTTP_PROTOCOL" value="{C:1}" /> </serverVariables> <action type="None" /> </rule>   <rule name="Redirect to www" stopProcessing="true"> <match url="(.*)" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> </conditions> <action type="Redirect" url="{HTTP_PROTOCOL}://www.localtest.me/{R:1}" /> </rule> Option 4 – Multi-rule Just to be complete I’ll include an example of how to achieve the same thing with multiple rules. I don’t see any reason to use it over the previous examples, but I’ll include an example anyway.  Note that it will only work with the “Match All” setting for the conditions. <rule name="Redirect to www - http" stopProcessing="true"> <match url="(.*)" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> <add input="{HTTPS}" pattern="off" /> </conditions> <action type="Redirect" url="http://www.localtest.me/{R:1}" /> </rule> <rule name="Redirect to www - https" stopProcessing="true"> <match url="(.*)" /> <conditions logicalGrouping="MatchAll" trackAllCaptures="false"> <add input="{HTTP_HOST}" pattern="^localtest\.me$" /> <add input="{HTTPS}" pattern="on" /> </conditions> <action type="Redirect" url="https://www.localtest.me/{R:1}" /> </rule> Conclusion Above are four working examples of methods to call the protocol (HTTP or HTTPS) from the action of a URL Rewrite rule.  You can use whichever method you most prefer.  I’ve listed them in the order that I favor them, although I could see some people preferring Option 2 as their first choice.  In any of the cases, hopefully you can use this as a reference for when you need to use the protocol in the rule’s action when writing your URL Rewrite rules. Further information: Viewing all Server Variable for a site. URL Parts available to URL Rewrite Rules Further URL Rewrite articles

    Read the article

  • Selling Federal Enterprise Architecture (EA)

    - by TedMcLaughlan
    Selling Federal Enterprise Architecture A taxonomy of subject areas, from which to develop a prioritized marketing and communications plan to evangelize EA activities within and among US Federal Government organizations and constituents. Any and all feedback is appreciated, particularly in developing and extending this discussion as a tool for use – more information and details are also available. "Selling" the discipline of Enterprise Architecture (EA) in the Federal Government (particularly in non-DoD agencies) is difficult, notwithstanding the general availability and use of the Federal Enterprise Architecture Framework (FEAF) for some time now, and the relatively mature use of the reference models in the OMB Capital Planning and Investment (CPIC) cycles. EA in the Federal Government also tends to be a very esoteric and hard to decipher conversation – early apologies to those who agree to continue reading this somewhat lengthy article. Alignment to the FEAF and OMB compliance mandates is long underway across the Federal Departments and Agencies (and visible via tools like PortfolioStat and ITDashboard.gov – but there is still a gap between the top-down compliance directives and enablement programs, and the bottom-up awareness and effective use of EA for either IT investment management or actual mission effectiveness. "EA isn't getting deep enough penetration into programs, components, sub-agencies, etc.", verified a panelist at the most recent EA Government Conference in DC. Newer guidance from OMB may be especially difficult to handle, where bottom-up input can't be accurately aligned, analyzed and reported via standardized EA discipline at the Agency level – for example in addressing the new (for FY13) Exhibit 53D "Agency IT Reductions and Reinvestments" and the information required for "Cloud Computing Alternatives Evaluation" (supporting the new Exhibit 53C, "Agency Cloud Computing Portfolio"). Therefore, EA must be "sold" directly to the communities that matter, from a coordinated, proactive messaging perspective that takes BOTH the Program-level value drivers AND the broader Agency mission and IT maturity context into consideration. Selling EA means persuading others to take additional time and possibly assign additional resources, for a mix of direct and indirect benefits – many of which aren't likely to be realized in the short-term. This means there's probably little current, allocated budget to work with; ergo the challenge of trying to sell an "unfunded mandate". Also, the concept of "Enterprise" in large Departments like Homeland Security tends to cross all kinds of organizational boundaries – as Richard Spires recently indicated by commenting that "...organizational boundaries still trump functional similarities. Most people understand what we're trying to do internally, and at a high level they get it. The problem, of course, is when you get down to them and their system and the fact that you're going to be touching them...there's always that fear factor," Spires said. It is quite clear to the Federal IT Investment community that for EA to meet its objective, understandable, relevant value must be measured and reported using a repeatable method – as described by GAO's recent report "Enterprise Architecture Value Needs To Be Measured and Reported". What's not clear is the method or guidance to sell this value. In fact, the current GAO "Framework for Assessing and Improving Enterprise Architecture Management (Version 2.0)", a.k.a. the "EAMMF", does not include words like "sell", "persuade", "market", etc., except in reference ("within Core Element 19: Organization business owner and CXO representatives are actively engaged in architecture development") to a brief section in the CIO Council's 2001 "Practical Guide to Federal Enterprise Architecture", entitled "3.3.1. Develop an EA Marketing Strategy and Communications Plan." Furthermore, Core Element 19 of the EAMMF is advised to be applied in "Stage 3: Developing Initial EA Versions". This kind of EA sales campaign truly should start much earlier in the maturity progress, i.e. in Stages 0 or 1. So, what are the understandable, relevant benefits (or value) to sell, that can find an agreeable, participatory audience, and can pave the way towards success of a longer-term, funded set of EA mechanisms that can be methodically measured and reported? Pragmatic benefits from a useful EA that can help overcome the fear of change? And how should they be sold? Following is a brief taxonomy (it's a taxonomy, to help organize SME support) of benefit-related subjects that might make the most sense, in creating the messages and organizing an initial "engagement plan" for evangelizing EA "from within". An EA "Sales Taxonomy" of sorts. We're not boiling the ocean here; the subjects that are included are ones that currently appear to be urgently relevant to the current Federal IT Investment landscape. Note that successful dialogue in these topics is directly usable as input or guidance for actually developing early-stage, "Fit-for-Purpose" (a DoDAF term) Enterprise Architecture artifacts, as prescribed by common methods found in most EA methodologies, including FEAF, TOGAF, DoDAF and our own Oracle Enterprise Architecture Framework (OEAF). The taxonomy below is organized by (1) Target Community, (2) Benefit or Value, and (3) EA Program Facet - as in: "Let's talk to (1: Community Member) about how and why (3: EA Facet) the EA program can help with (2: Benefit/Value)". Once the initial discussion targets and subjects are approved (that can be measured and reported), a "marketing and communications plan" can be created. A working example follows the Taxonomy. Enterprise Architecture Sales Taxonomy Draft, Summary Version 1. Community 1.1. Budgeted Programs or Portfolios Communities of Purpose (CoPR) 1.1.1. Program/System Owners (Senior Execs) Creating or Executing Acquisition Plans 1.1.2. Program/System Owners Facing Strategic Change 1.1.2.1. Mandated 1.1.2.2. Expected/Anticipated 1.1.3. Program Managers - Creating Employee Performance Plans 1.1.4. CO/COTRs – Creating Contractor Performance Plans, or evaluating Value Engineering Change Proposals (VECP) 1.2. Governance & Communications Communities of Practice (CoP) 1.2.1. Policy Owners 1.2.1.1. OCFO 1.2.1.1.1. Budget/Procurement Office 1.2.1.1.2. Strategic Planning 1.2.1.2. OCIO 1.2.1.2.1. IT Management 1.2.1.2.2. IT Operations 1.2.1.2.3. Information Assurance (Cyber Security) 1.2.1.2.4. IT Innovation 1.2.1.3. Information-Sharing/ Process Collaboration (i.e. policies and procedures regarding Partners, Agreements) 1.2.2. Governing IT Council/SME Peers (i.e. an "Architects Council") 1.2.2.1. Enterprise Architects (assumes others exist; also assumes EA participants aren't buried solely within the CIO shop) 1.2.2.2. Domain, Enclave, Segment Architects – i.e. the right affinity group for a "shared services" EA structure (per the EAMMF), which may be classified as Federated, Segmented, Service-Oriented, or Extended 1.2.2.3. External Oversight/Constraints 1.2.2.3.1. GAO/OIG & Legal 1.2.2.3.2. Industry Standards 1.2.2.3.3. Official public notification, response 1.2.3. Mission Constituents Participant & Analyst Community of Interest (CoI) 1.2.3.1. Mission Operators/Users 1.2.3.2. Public Constituents 1.2.3.3. Industry Advisory Groups, Stakeholders 1.2.3.4. Media 2. Benefit/Value (Note the actual benefits may not be discretely attributable to EA alone; EA is a very collaborative, cross-cutting discipline.) 2.1. Program Costs – EA enables sound decisions regarding... 2.1.1. Cost Avoidance – a TCO theme 2.1.2. Sequencing – alignment of capability delivery 2.1.3. Budget Instability – a Federal reality 2.2. Investment Capital – EA illuminates new investment resources via... 2.2.1. Value Engineering – contractor-driven cost savings on existing budgets, direct or collateral 2.2.2. Reuse – reuse of investments between programs can result in savings, chargeback models; avoiding duplication 2.2.3. License Refactoring – IT license & support models may not reflect actual or intended usage 2.3. Contextual Knowledge – EA enables informed decisions by revealing... 2.3.1. Common Operating Picture (COP) – i.e. cross-program impacts and synergy, relative to context 2.3.2. Expertise & Skill – who truly should be involved in architectural decisions, both business and IT 2.3.3. Influence – the impact of politics and relationships can be examined 2.3.4. Disruptive Technologies – new technologies may reduce costs or mitigate risk in unanticipated ways 2.3.5. What-If Scenarios – can become much more refined, current, verifiable; basis for Target Architectures 2.4. Mission Performance – EA enables beneficial decision results regarding... 2.4.1. IT Performance and Optimization – towards 100% effective, available resource utilization 2.4.2. IT Stability – towards 100%, real-time uptime 2.4.3. Agility – responding to rapid changes in mission 2.4.4. Outcomes –measures of mission success, KPIs – vs. only "Outputs" 2.4.5. Constraints – appropriate response to constraints 2.4.6. Personnel Performance – better line-of-sight through performance plans to mission outcome 2.5. Mission Risk Mitigation – EA mitigates decision risks in terms of... 2.5.1. Compliance – all the right boxes are checked 2.5.2. Dependencies –cross-agency, segment, government 2.5.3. Transparency – risks, impact and resource utilization are illuminated quickly, comprehensively 2.5.4. Threats and Vulnerabilities – current, realistic awareness and profiles 2.5.5. Consequences – realization of risk can be mapped as a series of consequences, from earlier decisions or new decisions required for current issues 2.5.5.1. Unanticipated – illuminating signals of future or non-symmetric risk; helping to "future-proof" 2.5.5.2. Anticipated – discovering the level of impact that matters 3. EA Program Facet (What parts of the EA can and should be communicated, using business or mission terms?) 3.1. Architecture Models – the visual tools to be created and used 3.1.1. Operating Architecture – the Business Operating Model/Architecture elements of the EA truly drive all other elements, plus expose communication channels 3.1.2. Use Of – how can the EA models be used, and how are they populated, from a reasonable, pragmatic yet compliant perspective? What are the core/minimal models required? What's the relationship of these models, with existing system models? 3.1.3. Scope – what level of granularity within the models, and what level of abstraction across the models, is likely to be most effective and useful? 3.2. Traceability – the maturity, status, completeness of the tools 3.2.1. Status – what in fact is the degree of maturity across the integrated EA model and other relevant governance models, and who may already be benefiting from it? 3.2.2. Visibility – how does the EA visibly and effectively prove IT investment performance goals are being reached, with positive mission outcome? 3.3. Governance – what's the interaction, participation method; how are the tools used? 3.3.1. Contributions – how is the EA program informed, accept submissions, collect data? Who are the experts? 3.3.2. Review – how is the EA validated, against what criteria?  Taxonomy Usage Example:   1. To speak with: a. ...a particular set of System Owners Facing Strategic Change, via mandate (like the "Cloud First" mandate); about... b. ...how the EA program's visible and easily accessible Infrastructure Reference Model (i.e. "IRM" or "TRM"), if updated more completely with current system data, can... c. ...help shed light on ways to mitigate risks and avoid future costs associated with NOT leveraging potentially-available shared services across the enterprise... 2. ....the following Marketing & Communications (Sales) Plan can be constructed: a. Create an easy-to-read "Consequence Model" that illustrates how adoption of a cloud capability (like elastic operational storage) can enable rapid and durable compliance with the mandate – using EA traceability. Traceability might be from the IRM to the ARM (that identifies reusable services invoking the elastic storage), and then to the PRM with performance measures (such as % utilization of purchased storage allocation) included in the OMB Exhibits; and b. Schedule a meeting with the Program Owners, timed during their Acquisition Strategy meetings in response to the mandate, to use the "Consequence Model" for advising them to organize a rapid and relevant RFI solicitation for this cloud capability (regarding alternatives for sourcing elastic operational storage); and c. Schedule a series of short "Discovery" meetings with the system architecture leads (as agreed by the Program Owners), to further populate/validate the "As-Is" models and frame the "To Be" models (via scenarios), to better inform the RFI, obtain the best feedback from the vendor community, and provide potential value for and avoid impact to all other programs and systems. --end example -- Note that communications with the intended audience should take a page out of the standard "Search Engine Optimization" (SEO) playbook, using keywords and phrases relating to "value" and "outcome" vs. "compliance" and "output". Searches in email boxes, internal and external search engines for phrases like "cost avoidance strategies", "mission performance metrics" and "innovation funding" should yield messages and content from the EA team. This targeted, informed, practical sales approach should result in additional buy-in and participation, additional EA information contribution and model validation, development of more SMEs and quick "proof points" (with real-life testing) to bolster the case for EA. The proof point here is a successful, timely procurement that satisfies not only the external mandate and external oversight review, but also meets internal EA compliance/conformance goals and therefore is more transparently useful across the community. In short, if sold effectively, the EA will perform and be recognized. EA won’t therefore be used only for compliance, but also (according to a validated, stated purpose) to directly influence decisions and outcomes. The opinions, views and analysis expressed in this document are those of the author and do not necessarily reflect the views of Oracle.

    Read the article

  • How to synchronize cuda threads when they are in the same loop and we need to synchronize them to ex

    - by Vickey
    Hi all, I have written a code and Now I want to implement this on cuda GPU but I'm new to synchronization so please help me with this, It's little urgent to me. Below I'm presenting the code and I want to that LOOP1 to be executed by all threads (heance I want to this portion to take advantage of cuda and the remaining portion (the portion other from the LOOP1) is to be executed by only a single thread. do{ point_set = master_Q[(*num_mas) - 1].q; List* temp = point_set; List* pa = point_set; if(master_Q[num_mas[0] - 1].max) max_level = (int) (ceilf(il2 * log(master_Q[num_mas[0] - 1].max))); *num_mas = (*num_mas) - 1; while(point_set){ List* insert_ele = temp; while(temp){ insert_ele = temp; if((insert_ele->dist[insert_ele->dist_index-1] <= pow(2, max_level-1)) || (top_level == max_level)){ if(point_set == temp){ point_set = temp->next; pa = temp->next; } else{ pa->next = temp->next; } temp = NULL; List* new_point_set = point_set; float maximum_dist = 0; if(parent->p_index != insert_ele->point_index){ List* tmp = new_point_set; float *b = &(data[(insert_ele->point_index)*point_len]); **LOOP 1:** while(tmp){ float *c = &(data[(tmp->point_index)*point_len]); float sum = 0.; for(int j = 0; j < point_len; j+=2){ float d1 = b[j] - c[j]; float d2 = b[j+1] - c[j+1]; d1 *= d1; d2 *= d2; sum = sum + d1 + d2; } tmp->dist[tmp->dist_index] = sqrt(sum); if(maximum_dist < tmp->dist[tmp->dist_index]) maximum_dist = tmp->dist[tmp->dist_index]; tmp->dist_index = tmp->dist_index+1; tmp = tmp->next; } max_distance = maximum_dist; } while(new_point_set || insert_ele){ List* far, *par, *tmp, *tmp_new; far = NULL; tmp = new_point_set; tmp_new = NULL; float level_dist = pow(2, max_level-1); float maxdist = 0, maxp = 0; while(tmp){ if(tmp->dist[(tmp->dist_index)-1] > level_dist){ if(maxdist < tmp->dist[tmp->dist_index-1]) maxdist = tmp->dist[tmp->dist_index-1]; if(tmp == new_point_set){ new_point_set = tmp->next; par = tmp->next; } else{ par->next = tmp->next; } if(far == NULL){ far = tmp; tmp_new = far; } else{ tmp_new->next = tmp; tmp_new = tmp; } if(parent->p_index != insert_ele->point_index) tmp->dist_index = tmp->dist_index - 1; tmp = tmp->next; tmp_new->next = NULL; } else{ par = tmp; if(maxp < tmp->dist[(tmp->dist_index)-1]) maxp = tmp->dist[(tmp->dist_index)-1]; tmp = tmp->next; } } if(0 == maxp){ tmp = new_point_set; aloc_mem[*tree_index].p_index = insert_ele->point_index; aloc_mem[*tree_index].no_child = 0; aloc_mem[*tree_index].level = max_level--; parent->children_index[parent->no_child++] = *tree_index; parent = &(aloc_mem[*tree_index]); tree_index[0] = tree_index[0]+1; while(tmp){ aloc_mem[*tree_index].p_index = tmp->point_index; aloc_mem[(*tree_index)].no_child = 0; aloc_mem[(*tree_index)].level = master_Q[(*cur_count_Q)-1].level; parent->children_index[parent->no_child] = *tree_index; parent->no_child = parent->no_child + 1; (*tree_index)++; tmp = tmp->next; } cur_count_Q[0] = cur_count_Q[0]-1; new_point_set = NULL; } master_Q[*num_mas].q = far; master_Q[*num_mas].parent = parent; master_Q[*num_mas].valid = true; master_Q[*num_mas].max = maxdist; master_Q[*num_mas].level = max_level; num_mas[0] = num_mas[0]+1; if(0 != maxp){ aloc_mem[*tree_index].p_index = insert_ele->point_index; aloc_mem[*tree_index].no_child = 0; aloc_mem[*tree_index].level = max_level; parent->children_index[parent->no_child++] = *tree_index; parent = &(aloc_mem[*tree_index]); tree_index[0] = tree_index[0]+1; if(maxp){ int new_level = ((int) (ceilf(il2 * log(maxp)))) +1; if (new_level < (max_level-1)) max_level = new_level; else max_level--; } else max_level--; } if( 0 == maxp ) insert_ele = NULL; } } else{ if(NULL == temp->next){ master_Q[*num_mas].q = point_set; master_Q[*num_mas].parent = parent; master_Q[*num_mas].valid = true; master_Q[*num_mas].level = max_level; num_mas[0] = num_mas[0]+1; } pa = temp; temp = temp->next; } } if((*num_mas) > 1){ List *temp2 = master_Q[(*num_mas)-1].q; while(temp2){ List* temp3 = master_Q[(*num_mas)-2].q; master_Q[(*num_mas)-2].q = temp2; if((master_Q[(*num_mas)-1].parent)->p_index != (master_Q[(*num_mas)-2].parent)->p_index){ temp2->dist_index = temp2->dist_index - 1; } temp2 = temp2->next; master_Q[(*num_mas)-2].q->next = temp3; } num_mas[0] = num_mas[0]-1; } point_set = master_Q[(*num_mas)-1].q; temp = point_set; pa = point_set; parent = master_Q[(*num_mas)-1].parent; max_level = master_Q[(*num_mas)-1].level; if(master_Q[(*num_mas)-1].max) if( max_level > ((int) (ceilf(il2 * log(master_Q[(*num_mas)-1].max)))) +1) max_level = ((int) (ceilf(il2 * log(master_Q[(*num_mas)-1].max)))) +1; num_mas[0] = num_mas[0]-1; } }while(*num_mas > 0);

    Read the article

  • can't install psycopg2 in my env on mac os x lion

    - by Alexander Ovchinnikov
    I tried install psycopg2 via pip in my virtual env, but got this error: ld: library not found for -lpq (full log here: http://pastebin.com/XdmGyJ4u ) I tried install postgres 9.1 from .dmg and via port, (gksks)iMac-Alexander:~ lorddaedra$ locate libpq /Developer/SDKs/MacOSX10.7.sdk/usr/include/libpq /Developer/SDKs/MacOSX10.7.sdk/usr/include/libpq/libpq-fs.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/libpq-events.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/libpq-fe.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/internal/libpq /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/internal/libpq/pqcomm.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/internal/libpq-int.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/auth.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/be-fsstubs.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/crypt.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/hba.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/ip.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/libpq-be.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/libpq-fs.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/libpq.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/md5.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/pqcomm.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/pqformat.h /Developer/SDKs/MacOSX10.7.sdk/usr/include/postgresql/server/libpq/pqsignal.h /Developer/SDKs/MacOSX10.7.sdk/usr/lib/libpq.5.3.dylib /Developer/SDKs/MacOSX10.7.sdk/usr/lib/libpq.5.dylib /Developer/SDKs/MacOSX10.7.sdk/usr/lib/libpq.a /Developer/SDKs/MacOSX10.7.sdk/usr/lib/libpq.dylib /Library/PostgreSQL/9.1/doc/postgresql/html/install-windows-libpq.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-async.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-build.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-cancel.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-connect.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-control.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-copy.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-envars.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-events.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-example.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-exec.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-fastpath.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-ldap.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-misc.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-notice-processing.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-notify.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-pgpass.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-pgservice.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-ssl.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-status.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq-threading.html /Library/PostgreSQL/9.1/doc/postgresql/html/libpq.html /Library/PostgreSQL/9.1/include/libpq /Library/PostgreSQL/9.1/include/libpq/libpq-fs.h /Library/PostgreSQL/9.1/include/libpq-events.h /Library/PostgreSQL/9.1/include/libpq-fe.h /Library/PostgreSQL/9.1/include/postgresql/internal/libpq /Library/PostgreSQL/9.1/include/postgresql/internal/libpq/pqcomm.h /Library/PostgreSQL/9.1/include/postgresql/internal/libpq-int.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq /Library/PostgreSQL/9.1/include/postgresql/server/libpq/auth.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/be-fsstubs.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/crypt.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/hba.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/ip.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/libpq-be.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/libpq-fs.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/libpq.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/md5.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/pqcomm.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/pqformat.h /Library/PostgreSQL/9.1/include/postgresql/server/libpq/pqsignal.h /Library/PostgreSQL/9.1/lib/libpq.5.4.dylib /Library/PostgreSQL/9.1/lib/libpq.5.dylib /Library/PostgreSQL/9.1/lib/libpq.a /Library/PostgreSQL/9.1/lib/libpq.dylib /Library/PostgreSQL/9.1/lib/postgresql/libpqwalreceiver.so /Library/PostgreSQL/9.1/pgAdmin3.app/Contents/Frameworks/libpq.5.dylib /Library/PostgreSQL/psqlODBC/lib/libpq.5.4.dylib /Library/PostgreSQL/psqlODBC/lib/libpq.5.dylib /Library/PostgreSQL/psqlODBC/lib/libpq.dylib /Library/WebServer/Documents/postgresql/html/install-windows-libpq.html /Library/WebServer/Documents/postgresql/html/libpq-async.html /Library/WebServer/Documents/postgresql/html/libpq-build.html /Library/WebServer/Documents/postgresql/html/libpq-cancel.html /Library/WebServer/Documents/postgresql/html/libpq-connect.html /Library/WebServer/Documents/postgresql/html/libpq-control.html /Library/WebServer/Documents/postgresql/html/libpq-copy.html /Library/WebServer/Documents/postgresql/html/libpq-envars.html /Library/WebServer/Documents/postgresql/html/libpq-events.html /Library/WebServer/Documents/postgresql/html/libpq-example.html /Library/WebServer/Documents/postgresql/html/libpq-exec.html /Library/WebServer/Documents/postgresql/html/libpq-fastpath.html /Library/WebServer/Documents/postgresql/html/libpq-ldap.html /Library/WebServer/Documents/postgresql/html/libpq-misc.html /Library/WebServer/Documents/postgresql/html/libpq-notice-processing.html /Library/WebServer/Documents/postgresql/html/libpq-notify.html /Library/WebServer/Documents/postgresql/html/libpq-pgpass.html /Library/WebServer/Documents/postgresql/html/libpq-pgservice.html /Library/WebServer/Documents/postgresql/html/libpq-ssl.html /Library/WebServer/Documents/postgresql/html/libpq-status.html /Library/WebServer/Documents/postgresql/html/libpq-threading.html /Library/WebServer/Documents/postgresql/html/libpq.html /opt/local/include/postgresql90/internal/libpq /opt/local/include/postgresql90/internal/libpq/pqcomm.h /opt/local/include/postgresql90/internal/libpq-int.h /opt/local/include/postgresql90/libpq /opt/local/include/postgresql90/libpq/libpq-fs.h /opt/local/include/postgresql90/libpq-events.h /opt/local/include/postgresql90/libpq-fe.h /opt/local/include/postgresql90/server/libpq /opt/local/include/postgresql90/server/libpq/auth.h /opt/local/include/postgresql90/server/libpq/be-fsstubs.h /opt/local/include/postgresql90/server/libpq/crypt.h /opt/local/include/postgresql90/server/libpq/hba.h /opt/local/include/postgresql90/server/libpq/ip.h /opt/local/include/postgresql90/server/libpq/libpq-be.h /opt/local/include/postgresql90/server/libpq/libpq-fs.h /opt/local/include/postgresql90/server/libpq/libpq.h /opt/local/include/postgresql90/server/libpq/md5.h /opt/local/include/postgresql90/server/libpq/pqcomm.h /opt/local/include/postgresql90/server/libpq/pqformat.h /opt/local/include/postgresql90/server/libpq/pqsignal.h /opt/local/lib/postgresql90/libpq.5.3.dylib /opt/local/lib/postgresql90/libpq.5.dylib /opt/local/lib/postgresql90/libpq.a /opt/local/lib/postgresql90/libpq.dylib /opt/local/lib/postgresql90/libpqwalreceiver.so /opt/local/var/macports/sources/rsync.macports.org/release/tarballs/ports/databases/libpqxx /opt/local/var/macports/sources/rsync.macports.org/release/tarballs/ports/databases/libpqxx/Portfile /opt/local/var/macports/sources/rsync.macports.org/release/tarballs/ports/databases/libpqxx26 /opt/local/var/macports/sources/rsync.macports.org/release/tarballs/ports/databases/libpqxx26/Portfile /usr/include/libpq /usr/include/libpq/libpq-fs.h /usr/include/libpq-events.h /usr/include/libpq-fe.h /usr/include/postgresql/internal/libpq /usr/include/postgresql/internal/libpq/pqcomm.h /usr/include/postgresql/internal/libpq-int.h /usr/include/postgresql/server/libpq /usr/include/postgresql/server/libpq/auth.h /usr/include/postgresql/server/libpq/be-fsstubs.h /usr/include/postgresql/server/libpq/crypt.h /usr/include/postgresql/server/libpq/hba.h /usr/include/postgresql/server/libpq/ip.h /usr/include/postgresql/server/libpq/libpq-be.h /usr/include/postgresql/server/libpq/libpq-fs.h /usr/include/postgresql/server/libpq/libpq.h /usr/include/postgresql/server/libpq/md5.h /usr/include/postgresql/server/libpq/pqcomm.h /usr/include/postgresql/server/libpq/pqformat.h /usr/include/postgresql/server/libpq/pqsignal.h /usr/lib/libpq.5.3.dylib /usr/lib/libpq.5.dylib /usr/lib/libpq.a /usr/lib/libpq.dylib How to tell pip to use this lib in /Library/PostgreSQL/9.1/lib/ (or may be in /usr/lib)? or may be install this lib again in my env (i try keep my env isolated from mac as possible)

    Read the article

  • Yum update not working on CentOS 6.2 minimal install

    - by Owen
    Note: This is my first question on the stack exchange network so please give mercy and provide guidance where needed. I have installed a CentOS 6.2 KVM guest and I am having problem getting yum to work. This is my first time working with CentOS so I feel that it's a setting somewhere that I am missing but cannot find using google. Here are my steps; Downloaded CentOS-6.2-x86_64-minimal.iso, booted, and went through default steps (only questions asked where keyboard, timezone, root password and use entire hdd) Restarted, logged in, pinged google.com to no avail Set the following settings; vi /etc/resolv.conf nameserver 8.8.8.8 nameserver 8.8.4.4 vi /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE="eth0" HWADDR="52:54:00:42:1B:4A" #NM_CONTROLLED="yes" BOOTPROTO=none ONBOOT="yes" NETMASK=255.255.255.0 IPADDR=192.168.122.151 TYPE=Ethernet vi /etc/sysconfig/network NETWORKING=yes NETWORKING_IPV6=no HOSTNAME=server3.example.com GATEWAY=192.168.122.1 I can now ping google.com ping google.com PING google.com (173.194.70.139) 56(84) bytes of data. 64 bytes from fa-in-f139.1e100.net (173.194.70.139): icmp_seq=1 ttl=50 time=5.88 ms 64 bytes from fa-in-f139.1e100.net (173.194.70.139): icmp_seq=2 ttl=50 time=5.77 ms But I cannot 'yum update' yum update Loaded plugins: fastestmirror, presto Loading mirror speeds from cached hostfile Could not retrieve mirrorlist http://mirrorlist.centos.org/?release=6&arch=x86_64&repo=os error was 14: PYCURL ERROR 7 - "Failed to connect to 2a01:c0:2:4:216:3eff:fe0d:266d: Network is unreachable" Error: Cannot find a valid baseurl for repo: base My KVM guest is also NAT'd incase it's of concern.

    Read the article

  • "The system time has changed" events after waking from sleep

    - by Damir Arh
    Sometimes when my computer running Windows 7 wakes up from sleep, it has to adjust the time. When this happens the following system event is logged: <Event xmlns='http://schemas.microsoft.com/win/2004/08/events/event'> <System> <Provider Name='Microsoft-Windows-Kernel-General' Guid='{A68CA8B7-004F-D7B6-A698-07E2DE0F1F5D}'/> <EventID>1</EventID> <Version>0</Version> <Level>4</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8000000000000010</Keywords> <TimeCreated SystemTime='2010-03-06T19:09:57.500000000Z'/> <EventRecordID>10672</EventRecordID> <Correlation/> <Execution ProcessID='4' ThreadID='56'/> <Channel>System</Channel> <Computer>GAME</Computer> <Security/> </System> <EventData> <Data Name='NewTime'>2010-03-06T19:09:57.500000000Z</Data> <Data Name='OldTime'>2010-03-06T17:34:32.870117200Z</Data> </EventData> <RenderingInfo Culture='sl-SI'> <Message>The system time has changed to ?2010?-?03?-?06T19:09:57.500000000Z from ?2010?-?03?-?06T17:34:32.870117200Z.</Message> <Level>Information</Level> <Task></Task> <Opcode>Info</Opcode> <Channel>System</Channel> <Provider>Microsoft-Windows-Kernel-General</Provider> <Keywords> <Keyword>Time</Keyword> </Keywords> </RenderingInfo> </Event> When this happens (I noticed it twice until now) the old time always corresponds to the time when computer entered sleep. The problem is that if Windows Media Center is scheduled for recording during this time, it just skips it as if the computer was turned off. I never had this problem running Windows Vista on the same machine. Any ideas what could be causing this problem and how to solve it are welcome.

    Read the article

  • How best to troubleshoot a WIA issue through an IIS7 reverse proxy.

    - by CptSkippy
    I've got an Intranet site that uses Windows Authentication and is accessed through an IIS 7 Reverse Proxy. Using FireFox, Safari or Chrome it works fine. I'm prompted for credentials, I supply them and away I go. In IE 7/8 I get prompted for credentials but they're rejected and I eventually get a 401 not authorized error. The application server is configured for Windows Auth only and rejects basic authentication. I would be surprised if the front end proxy would accept Basic Auth so my suspicion is that it's a trust issue with my browser and IE isn't relaying the credentials however our IS Team has IE so locked down I'm unable to alter trust levels or even view the settings. How should I go about troubleshooting this problem? I'm at a loss and they've yet to respond to my support ticket.

    Read the article

  • Event ID: 861 - The Windows Firewall has detected an application listening for incoming traffic

    - by Chris Marisic
    Firstly, my machines aren't compromised any person suggesting such will be DV'd. The security logs on some of my networks client machines (all Windows Xp Sp3) get filled with these useless error messages. Security Failure Audit Detailed Tracking Event ID: 861 User: NT AUTHORITY\NETWORK SERVICE The Windows Firewall has detected an application listening for incoming traffic. Name: - Path: C:\WINDOWS\system32\svchost.exe Process identifier: 976 User account: NETWORK SERVICE User domain: NT AUTHORITY Service: Yes RPC server: No IP version: IPv4 IP protocol: UDP Port number: 55035 Allowed: No User notified: No It's always on various random ports of UDP so setting up a port exception isn't really an option. It's always from svchost or lsass both of which are running services from DLLs. One of the most offending processes seems to the be DnsCache. I have in my global policy under AT < Network < Network Connection < Widnows Firewall < Domain Profile (I haven't changed any standard profile options do both need configured? To allow remote administration and desktop exceptions and have a custom program exception list that has %SystemRoot%\system32\svchost.exe:*:enabled:svchost (Windows won't allow you to add this exception on a local machine but it let me have it on here in the global policy it just doesn't seem to do anything) %SystemRoot%\system32\lsass.exe:*enabled:lsass (I think this one ended all of my LSASS messages) %SystemRoot%\system32\dnsrslvr.dll:*:enabled:dnscache (I tried adding the dll itself to the exception list, this didn't seem to do anything) Is there really any other options left other than disabling the Windows Firewall entirely, disabling auditing entirely or just changing the event viewer to just auto overwrite when needed? I'd much rather fix the problem and get rid of these entries ever being created instead of just trying to cover up the problem.

    Read the article

  • Likewise DomainJoin hangs on Finishing krb5.conf configuration

    - by dreay
    Hello, I have a problem when joining a CentOS release 5.4 (Final) x64 machine to the domain after running domainjoin-cli --loglevel info --log . join domain.local password I obtain the following, which seems to hang on "20100428112821:INFO:Finishing krb5.conf configuration" 20100428112817:INFO:Domainjoin invoked with the join command (remaining arguments will be printed later): 20100428112817:INFO: [/opt/likewise/bin/domainjoin-cli] 20100428112817:INFO: [--loglevel] 20100428112817:INFO: [info] 20100428112817:INFO: [--log] 20100428112817:INFO: [/tmp/join_1.log] 20100428112817:INFO: [join] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwsmd] 20100428112817:INFO:Daemon [/etc/init.d/lwsmd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwsmd] 20100428112817:INFO:Daemon [/etc/init.d/lwsmd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwregd] 20100428112817:INFO:Daemon [/etc/init.d/lwregd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwregd] 20100428112817:INFO:Daemon [/etc/init.d/lwregd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/netlogond] 20100428112817:INFO:Daemon [/etc/init.d/netlogond]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/netlogond] 20100428112817:INFO:Daemon [/etc/init.d/netlogond]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwiod] 20100428112817:INFO:Daemon [/etc/init.d/lwiod]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lwiod] 20100428112817:INFO:Daemon [/etc/init.d/lwiod]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/dcerpcd] 20100428112817:INFO:Daemon [/etc/init.d/dcerpcd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/dcerpcd] 20100428112817:INFO:Daemon [/etc/init.d/dcerpcd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/eventlogd] 20100428112817:INFO:Daemon [/etc/init.d/eventlogd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/eventlogd] 20100428112817:INFO:Daemon [/etc/init.d/eventlogd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lsassd] 20100428112817:INFO:Daemon [/etc/init.d/lsassd]: status [0] 20100428112817:INFO:Checking status of daemon [/etc/init.d/lsassd] 20100428112817:INFO:Daemon [/etc/init.d/lsassd]: status [0] 20100428112817:INFO:Domainjoin invoked with 2 arg(s) to the join command: 20100428112817:INFO: [domain.local] 20100428112817:INFO: [default.user] 20100428112817:INFO:Adding ops (fqdn ops.domain.local) to /etc/hosts ip 192.168.246.5, removing ops, ops.domain.local, ops, ops.domain.local 20100428112817:INFO:Reading krb5 file /tmp/likewisetmpPkpAn5/etc/krb5.conf 20100428112817:INFO:Reading krb5 file /tmp/likewisetmpb6dkNX/etc/krb5.conf 20100428112817:INFO:Reading nsswitch file /etc/nsswitch.conf 20100428112817:INFO:Reading pam configuration 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/config-util.rpmnew 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/config-util 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/runuser-l 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/sshd 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/other 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/smtp.postfix 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/su-l 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-switch-mail-nox 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/kshell 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/authconfig 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/ekshell 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/run_init 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/screen 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/eject 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-auth.rpmnew 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-config-network-cmd 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-auth-ac 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/kbdrate 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/smtp.sendmail 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/chsh 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/setup 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-switch-mail 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/ksu 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/login 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/sudo-i 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/smtp 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/runuser 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/chfn 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/ppp 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/gssftp 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/remote 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/reboot 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/newrole 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/pm-powersave 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-auth 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/halt 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/other.rpmnew 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/atd 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/passwd 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/authconfig-tui 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/pm-hibernate 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/su 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/system-config-network 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/neat 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/pm-suspend-hybrid 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/crond 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/sudo 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/pm-suspend 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.d/poweroff 20100428112817:INFO:Reading pam file /tmp/likewisetmptrO2dQ/etc/pam.conf 20100428112817:INFO:File /tmp/likewisetmptrO2dQ/etc/pam.conf does not exist 20100428112817:INFO:Found config file /etc/ssh/sshd_config 20100428112817:INFO:Found binary /usr/sbin/sshd 20100428112817:INFO:Reading ssh file /etc/ssh/sshd_config 20100428112817:INFO:Found open sshd version 4.3.-1p2 20100428112817:INFO:Testing option ChallengeResponseAuthentication 20100428112817:INFO:Option ChallengeResponseAuthentication supported 20100428112817:INFO:Testing option UsePAM 20100428112817:INFO:Option UsePAM supported 20100428112817:INFO:Testing option PAMAuthenticationViaKBDInt 20100428112817:INFO:Option PAMAuthenticationViaKBDInt not supported 20100428112817:INFO:Testing option KbdInteractiveAuthentication 20100428112817:INFO:Option KbdInteractiveAuthentication supported 20100428112817:INFO:Testing option GSSAPIAuthentication 20100428112817:INFO:Option GSSAPIAuthentication supported 20100428112817:INFO:Testing option GSSAPICleanupCredentials 20100428112817:INFO:Option GSSAPICleanupCredentials supported 20100428112817:INFO:Found config file /etc/ssh/ssh_config 20100428112817:INFO:Found binary /usr/bin/ssh 20100428112817:INFO:Reading ssh file /etc/ssh/ssh_config 20100428112817:INFO:Testing option GSSAPIAuthentication 20100428112817:INFO:Option GSSAPIAuthentication supported 20100428112817:INFO:Testing option GSSAPIDelegateCredentials 20100428112817:INFO:Option GSSAPIDelegateCredentials supported 20100428112821:INFO:Running module join 20100428112821:INFO:Starting krb5.conf configuration (enabling) 20100428112821:INFO:Reading krb5 file /tmp/likewisetmpvgqQmT/etc/krb5.conf 20100428112821:WARNING:Short domain name not specified. Defaulting to 'betgenius' 20100428112821:INFO:Failed to run lwinet ads trusts. This is expected if not yet joined to the domain 20100428112821:INFO:Failed to run lwiinfo --details -m. This is expected if the auth daemon is not running 20100428112821:INFO:Writing krb5 file /tmp/likewisetmpvgqQmT/etc/krb5.conf 20100428112821:INFO:File /tmp/likewisetmpvgqQmT/etc/krb5.conf modified 20100428112821:INFO:Finishing krb5.conf configuration Has anyone seen this error before? and know of the fix?

    Read the article

  • BAT file will not run from Task Scheduler but will from Command Line

    - by wtaylor
    I'm trying to run a BAT script from Task Scheduler in Windows 2008 R2 and it runs for 3 seconds and then stops. It says it successfully completes but I know it doesn't. I can run this script from the command line directly, and it runs just fine. The bat file I'm running actually deletes files older than 7 days using "forfiles" then I'm mapping a network drive, moving the files across the network using robocopy, and then closing the network connection. I have taken the network and copy options out of the file and it still does the same thing. Here is how my file looks: rem This will delete the files from BBLEARN_stats forfiles -p "E:\BB_Maintenance_Data\DB_Backups\BBLEARN_stats" -m *.* -d -17 -c "cmd /c del @file" rem This will delete the files from BBLEARN_cms_doc forfiles -p "E:\BB_Maintenance_Data\DB_Backups\BBLEARN_cms_doc" -m *.* -d -14 -c "cmd /c del @path" rem This will delete the files from BBLEARN_admin forfiles -p "E:\BB_Maintenance_Data\DB_Backups\BBLEARN_admin" -m *.* -d -10 -c "cmd /c del @path" rem This will delete the files from BBLEARN_cms forfiles -p "E:\BB_Maintenance_Data\DB_Backups\BBLEARN_cms" -m *.* -d -10 -c "cmd /c del @path" rem This will delete the files from attendance_bb forfiles -p "E:\BB_Maintenance_Data\DB_Backups\attendance_bb" -m *.* -d -10 -c "cmd /c del @path" rem This will delete the files from BBLearn forfiles -p "E:\BB_Maintenance_Data\DB_Backups\BBLEARN" -m *.* -d -18 -c "cmd /c del @path" rem This will delete the files from Logs forfiles -p "E:\BB_Maintenance_Data\logs" -m *.* -d -10 -c "cmd /c del @path" NET USE Z: \\10.20.102.225\coursebackups\BB_DB_Backups /user:cie oly2008 ROBOCOPY E:\BB_Maintenance_Data Z: /e /XO /FFT /PURGE /NP /LOG:BB_DB_Backups.txt openfiles /disconnect /id * NET USE Z: /delete /y This is happening on 2 servers when trying to run commands from inside a BAT file. The other server is giving an error if (0xFFFFFFFF) but that file is running a CALL C:\dir\dir\file.bat -options and I've used commands like that before in Server 2003. Here is the file for this file: call C:\blackboard\apps\content-exchange\bin\batch_ImportExport.bat -f backup_batch_file.txt -l 1 -t archive NET USE Z: \\10.20.102.225\coursebackups\BB_Course_Backups /user:cie oly2008 ROBOCOPY E:\ Z: /move /e /LOG+:BB_Move_Course_Backups.txt openfiles /disconnect /id * NET USE Z: /delete /y Any help would be GREAT. Thanks

    Read the article

  • Exchange 2007 Owa (OnlineVersion) can not authenticate

    - by DingosBarn
    Exchange Authentication dll: https://red002.mail.emea.microsoftonline.com/owa/auth/owaauth.dll sending style is: request.Method = "POST"; request.ContentType = "application/x-www-form-urlencoded"; And sending following message destination=https://red002.mail.emea.microsoftonline.com/owa/[email protected]/?ae=Folder&t=IPF.Appointment&[email protected]&password=xxxx I'm getting this error: The remote server returned an error: (400) Bad Request. If I use the path in a webbrowser it is accesable. It is not a bad request indeed. The server is Exchange server 2007 and replaced the path for owa. But it can not auth the path?

    Read the article

  • Exchange 2003: Fresh install, couple noob questions.

    - by Eli
    Hi All, Thanks for reading! I have a small network set up for a local office here, and have a fresh install of Exchange 2003 on our sole-server PDC. The network uses one domain, call it ourdomain.net, which is DNSed locally, but not DNSed for the actual domain, so ourdomain.net works from within the network, but from outside, it's just pointed to some domain parking. I have a completely different domain, call it emaildomain.com, which is currently setup for our website and email, which is hosted with a standard hosting company. We've been using a combination of Thunderbird and Outlook (with local .pst files) for email. I've been asked to setup Exchange to work with our email, but am not familiar with it. The install seems to have gone just fine. The question is: How do I get email from a domain outside our network to work with the exchange server? Do I need to move the email for that domain to point to our local server (I so hope not!), or can I just set exchange so somehow slurp mail from the existing mailboxes on our host for that domain's mail? Or are there better ideas I don't know to ask for? Any help very appreciated - thanks!

    Read the article

  • No internet connection using Edimax routers

    - by idan315
    I have two computers connected to a router, connected to my ADSL modem by PPPoE. One of those computrs use Windows XP, the other uses Windows 7. The computer using Windows 7 keeps getting limited or no connectivity, and I can't use it to connect to the internet. Connecting the computer to the modem without the router 'in the way' worked, and I was able to use the internet - which led me to believe that the problem is with my router. However, I have changed my router, and the problem persists. I am really lost on how to approach this problem. Possible leads: when I view the network information, I see that my computer is connected to 'Multiple Networks'. One of those is "Network 4" (probably my router), and the other is Unidentified network. I don't know how to make the "Unidentified Network" disappear, or why is it even there in the first place. When I try using "ipconfig", I have two default gateway IPs. The first is 0.0.0.0, and the second is the IP of my router (192.168.2.1). The first router was Edimax BR-6204Wg. The second one I've tried connecting is BR-6424n. Any ideas?

    Read the article

  • Per client DNS server assignment using Pfsense

    - by Trix
    I have a network where pfsense is the gateway. There are two sets of clients that I want. One where there will be some restrictions to the network (example, IM being blocked) and one network where there are no restrictions. One easy way I thought about doing this was assigning the different domains different DNS servers. One set could use OpenDNS, the other could use Google's Public DNS. The set with OpenDNS would have the filter options on (using OpenDNS' dashboard, I can check block IM .... so I do not manually need to block login.oscar.aol.com, meebo.com, gmail chat ....etc). So the problem is the DHCP server looks like it will only assign a single set of DNS servers to clients. Is there a way to set a per client assignment? Is there a better way to obtain what I want to obtain. This is just a small home network. I do not need anything fancy, but I do need this functionality in one way or another.

    Read the article

  • Finding cause of TCP retransmission within a LAN

    - by Surreal
    Hello denizens of Server Fault I have an irritating problem with a LAN of about 100 computers, 2 Windows domain servers, and 12 VoIP phones. Since their installation around a year ago, every week or so, we notice a VoIP phone resetting itself - occasionally in the middle of a call. Simultaneously there are often signs of temporary loss of connection on computers: freezes in explorer while accessing network shares, errors in our administration software due to loss of connection to the database server. I have been doing some Wireshark monitoring on the connection between the VoIP PBX and the rest of the network. Wireshark picks up a clump of retransmitted TCP packets at the times when we record phone restarts. The Wireshark log shows about 2 clusters of retransmissions a day ranging from 5 packets to hundreds. Those in each cluster are mainly between the PBX and some set of the VoIP phones, but not always the same set. Often retransmissions at the same time are to phones connected to the same switch, but sometimes retransmissions occur together to phones at opposite ends of the network. There are usually some coincident retransmissions in passing TCP traffic, for example between client machines and the file servers. The spikes in retransmissions and phone resets do not correlate well with when the network is heavily loaded. They seem to occur slightly more during the day, but most in the evening, when traffic should be decreasing. They occur reasonably often late at night when most computers are turned off and traffic should be lowest. Do you have any ideas that might help diagnose the cause of problems like this? One thing I have not yet tried, but should have, is updating the firmware of all the switches.

    Read the article

  • VMWare Server Windows 2008 NAT Problem

    - by David
    At my new job our workstations run Windows Server 2008. However, for the specific task for which I've been hired, I need to set up a couple Linux VMs. So I grabbed the free VMWare Server and created an Ubuntu image and a Slackware image. (The former to more closely mimic the production server, the latter because I'm more familiar with it.) For desktop security purposes I need to use NAT for the network access (I would have preferred bridged, but I'm told that would go against some policy here and my whole workstation would be sandboxed from the switch). However, I can't seem to get it working right. I can ping out from the VMs to LAN addresses as well as internet addresses. I can resolve DNS names. However, attempts to use a web browser or perform any kind of higher-level interaction like that just time out. Googling around yesterday led me to various workarounds that were similar, but didn't solve my specific situation. (For example, Norton firewall blocking the connection on the host, or even the Windows firewall.) I also saw some forum posts where people said it's a known issue with VMWare and Windows Server 2008 (and Windows 7). So far I haven't been able to find a suggestion that gets me past this roadblock. I'm really not very familiar with managing a Windows Server 2008 box, so it's possible there's just some security setting somewhere that I need to modify. Does anybody have any suggestions on where I should look? UPDATE: I'm now looking at the "Network and Sharing Center" on the host workstation and it shows "VMWare Network Adapter VMnet8" (which is what I'm using) as an "Unidentified network" with "No Internet access." Looks like I can't modify ICS under the group policy. Any suggestions on how to allow this connection to have internet access?

    Read the article

  • Apache2 benchmarks - very poor performance

    - by andrzejp
    I have two servers on which I test the configuration of apache2. The first server: 4GB of RAM, AMD Athlon (tm) 64 X2 Dual Core Processor 5600 + Apache 2.2.3, mod_php, mpm prefork: Settings: Timeout 100 KeepAlive On MaxKeepAliveRequests 150 KeepAliveTimeout 4 <IfModule Mpm_prefork_module> StartServers 7 MinSpareServers 15 MaxSpareServers 30 MaxClients 250 MaxRequestsPerChild 2000 </ IfModule> Compiled in modules: core.c mod_log_config.c mod_logio.c prefork.c http_core.c mod_so.c Second server: 8GB of RAM, Intel (R) Core (TM) i7 CPU [email protected] Apache 2.2.9, **fcgid, mpm worker, suexec** PHP scripts are running via fcgi-wrapper Settings: Timeout 100 KeepAlive On MaxKeepAliveRequests 100 KeepAliveTimeout 4 <IfModule Mpm_worker_module> StartServers 10 MaxClients 200 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 1000 </ IfModule> Compiled in modules: core.c mod_log_config.c mod_logio.c worker.c http_core.c mod_so.c The following test results, which are very strange! New server (dynamic content - php via fcgid+suexec): Server Software: Apache/2.2.9 Server Hostname: XXXXXXXX Server Port: 80 Document Path: XXXXXXX Document Length: 179512 bytes Concurrency Level: 10 Time taken for tests: 0.26276 seconds Complete requests: 1000 Failed requests: 0 Total transferred: 179935000 bytes HTML transferred: 179512000 bytes Requests per second: 38.06 Transfer rate: 6847.88 kb/s received Connnection Times (ms) min avg max Connect: 2 4 54 Processing: 161 257 449 Total: 163 261 503 Old server (dynamic content - mod_php): Server Software: Apache/2.2.3 Server Hostname: XXXXXX Server Port: 80 Document Path: XXXXXX Document Length: 187537 bytes Concurrency Level: 10 Time taken for tests: 173.073 seconds Complete requests: 1000 Failed requests: 22 (Connect: 0, Length: 22, Exceptions: 0) Total transferred: 188003372 bytes HTML transferred: 187546372 bytes Requests per second: 5777.91 Transfer rate: 1086267.40 kb/s received Connnection Times (ms) min avg max Connect: 3 3 28 Processing: 298 1724 26615 Total: 301 1727 26643 Old server: Static content (jpg file) Server Software: Apache/2.2.3 Server Hostname: xxxxxxxxx Server Port: 80 Document Path: /images/top2.gif Document Length: 40486 bytes Concurrency Level: 100 Time taken for tests: 3.558 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 40864400 bytes HTML transferred: 40557482 bytes Requests per second: 281.09 [#/sec] (mean) Time per request: 355.753 [ms] (mean) Time per request: 3.558 [ms] (mean, across all concurrent requests) Transfer rate: 11217.51 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 3 11 4.5 12 23 Processing: 40 329 61.4 339 1009 Waiting: 6 282 55.2 293 737 Total: 43 340 63.0 351 1020 New server - static content (jpg file) Server Software: Apache/2.2.9 Server Hostname: XXXXX Server Port: 80 Document Path: /images/top2.gif Document Length: 40486 bytes Concurrency Level: 100 Time taken for tests: 3.571531 seconds Complete requests: 1000 Failed requests: 0 Write errors: 0 Total transferred: 41282792 bytes HTML transferred: 41030080 bytes Requests per second: 279.99 [#/sec] (mean) Time per request: 357.153 [ms] (mean) Time per request: 3.572 [ms] (mean, across all concurrent requests) Transfer rate: 11287.88 [Kbytes/sec] received Connection Times (ms) min mean[+/-sd] median max Connect: 2 63 24.8 66 119 Processing: 124 278 31.8 282 391 Waiting: 3 70 28.5 66 164 Total: 126 341 35.9 350 443 I noticed that in the apache error.log is a lot of entries: [notice] mod_fcgid: call /www/XXXXX/public_html/forum/index.php with wrapper /www/php-fcgi-scripts/XXXXXX/php-fcgi-starter What I have omitted, or do not understand? Such a difference in requests per second? Is it possible? What could be the cause?

    Read the article

  • DNAT to 127.0.0.1 with iptables / Destination access control for transparent SOCKS proxy

    - by cdauth
    I have a server running on my local network that acts as a router for the computers in my network. I want to achieve now that outgoing TCP requests to certain IP addresses are tunnelled through an SSH connection, without giving the people from my network the possibility to use that SSH tunnel to connect to arbitrary hosts. The approach I had in mind until now was to have an instance of redsocks listening on localhost and to redirect all outgoing requests to the IP addresses I want to divert to that redsocks instance. I added the following iptables rule: iptables -t nat -A PREROUTING -p tcp -d 1.2.3.4 -j DNAT --to-destination 127.0.0.1:12345 Apparently, the Linux kernel considers packets coming from a non-127.0.0.0/8 address to an 127.0.0.0/8 address as “Martian packets” and drops them. What worked, though, was to have redsocks listen on eth0 instead of lo and then have iptables DNAT the packets to the eth0 address instead (or using a REDIRECT rule). The problem about this is that then every computer on my network can use the redsocks instance to connect to every host on the internet, but I want to limit its usage to a certain set of IP addresses only. Is there any way to make iptables DNAT packets to 127.0.0.1? Otherwise, does anyone have an idea how I could achieve my goal without opening up the tunnel to everyone? Update: I have also tried to change the source of the packets, without any success: iptables -t nat -A POSTROUTING -p tcp -s 192.168.1.0/24 -d 1.2.3.4 -j SNAT --to-source 127.0.0.1 iptables -t nat -A POSTROUTING -p tcp -s 192.168.1.0/24 -d 127.0.0.1 -j SNAT --to-source 127.0.0.1

    Read the article

  • Using dnsmasq for accessing multiple nameservers assigned by DHCP

    - by Ash
    At my work desktop running openSUSE 11.4, I have a local network which gets its address, domain (work.site) and nameservers (10.100.1.1, 10.100.1.2) info through DHCP - which get written into /etc/resolv.conf I get to access the internet using the work network, and these 2 nameservers end up returning the entries for any public domain name lookups on the internet. I also have a private VPN that I end up connecting. The nameserver (10.111.1.1) and domain (private.site) are rarely bound to change for this network, but currently they're pushed by the openVPN client into networkmanager, and which also gets merged with the existing /etc/resolv.conf My resolv.conf ultimately ends up looking like this: search private.site work.site nameserver 127.0.0.1 nameserver 10.111.1.1 nameserver 10.100.1.1 As you can see the 2nd nameserver from my work network was pushed out because of the max 3 entry limitations. It is fine still, but would be a problem if that nameserver goes down for maintenance or something. So I found out that dnsmasq could help me here, and hence I setup dnsmasq just as a local DNS resolver without any DHCP support. So right now this is my /etc/dnsmasq.conf: resolv-file=/etc/resolv.conf server=/private.site/10.111.1.1 server=/1.111.10.in-addr.arpa/10.111.1.1 listen-address=127.0.0.1 bind-interfaces log-queries I've made dnsmasq get the list of nameservers from /etc/resolv.conf since NetworkManager seems to be updating this list correctly (for a max of 3 nameservers). I'm able to resolve the host names in both the networks correctly. So these are the questions I have: Is there a way I can make either NetworkManager or dhclient write out the list of nameservers somewhere else which I can make dnsmasq use as resolv-file ? How do I make dnsmasq use certain nameservers as the default for all queries ? Right now I notice that lookups for public domains on the internet are usually sent to both the nameservers - the one on work.site as well as private.site. It would be good if I can limit this only to work.site.

    Read the article

  • Windows Server 2008 DHCP with RRAS

    - by Guillermo Prandi
    I have a Windows Server 2008 R2 which is a member of a domain, but is placed in a remote location. The server is directly connected to Internet. Clients need to access a particular insecure TCP service in this server (ports 9730 and 9731). Since clients have dynamic IP addresses I cannot know in advance, I thought it would be nice to have them connected through a VPN in order to access the insecure service, but ONLY to access that service, like this: Client ------> VPN TUNNEL ------> (Insecure service at Server) | \----> (Normal internet access) I'd enable the insecure ports in the firewall only from VPN accesses. For this I configured RRAS in the server and gave it a static IP address range (172.19.1.2 through 172.19.1.254) to serve the clients. First I thought I could use DHCP to assign the addresses, but I cannot use DHCP in my LAN connection (not allowed by the hosting service). I tried configuring DHCP binding it to a Microsoft Loopback Adapter, but that's not supported as a DHCP source by RRAS. What I want to accomplish is to send specific DHCP options to the client (network mask, routing table, etc.). In particular: Prevent the client from having the server as default router (without changing the client's "use default gateway in remote network"). Have it as a route for the server's internal RRAS address only (172.19.1.1). Prevent the client from using a 255.255.0.0 mask for the 172.19.x.x network (a 255.255.255.0 mask would be better). Can I do that with RRAS only? How? Currently, the only solution I can think of is to use DHCP in the LAN adapter, but filter DHCP packets so they don't reach the provider's network. However, I'm not sure if that will work. Any suggestions are welcomed! Guille

    Read the article

  • LDAP over SSL/TLS working for everything but login on Ubuntu

    - by Oliver Nelson
    I have gotten OpenLDAP with SSL working on a test box with a signed certificate. I can use an LDAP tool on a Windows box to view the LDAP over SSL (port 636). But when I run dpkg-reconfigure ldap-auth-config to setup my local login to use ldaps, my login under a username in the directory doesn't work. If I change the config to use just plain ldap (port 389) it works just fine (I can login under a username in the directory). When its setup for ldaps I get Auth.log shows: Sep 5 13:48:27 boromir sshd[13453]: pam_ldap: ldap_simple_bind Can't contact LDAP server Sep 5 13:48:27 boromir sshd[13453]: pam_ldap: reconnecting to LDAP server... Sep 5 13:48:27 boromir sshd[13453]: pam_ldap: ldap_simple_bind Can't contact LDAP server I will provide whatever are needed. I'm not sure what else to include. Thanx for any insights... OLIVER

    Read the article

  • How can I calculate power consumption of my PC in Watt?

    - by Jitendra vyas
    How can I calculate power consumption of my PC in Watt, to prove my House owner ( I live on rent) , my PC doesn't consume much power? He blames me for Huge power bills even he too use Fridge, A.C. etc and his son watch the TV all the time. We both share one Power meter so for bill we pay 50%-50% but He is saying I use PC all the time even night i keep on for downloading. I just want to calculate power consumption of my PC then will calculate monthly expense of unit as per my City's per unit price for power. I've Windows: Microsoft Windows XP Professional 5.1.2600 Service Pack 3 Memory (RAM): 960 MB CPU Info: AMD Sempron(tm) Processor 2500+ CPU Speed: 1399.0 MHz Sound card: Vinyl AC'97 Audio (WAVE) Display Adapters: VIA/S3G UniChrome Pro IGP | NetMeeting driver | RDPDD Chained DD Monitors: 1 - 17inch LCD - LG Screen Resolution: 1280 X 768 - 32 bit Network: Network Present Network Adapters: Bluetooth Device (Personal Area Network) #2 | WAN (PPP/SLIP) Interface CD / DVD Drives: I: ELBY CLONEDRIVE COM Ports: COM1 | COM2 | COM7 | COM8 | COM9 | COM10 LPT Ports: LPT1 Mouse: 3 Button Wheel Mouse Present Hard Disks: C: 29.3GB | D: 29.3GB | E: 97.7GB | F: 97.7GB | G: 211.9GB USB Controllers: 5 host controllers. Firewire (1394): 1 host controllers. Manufacturer: Phoenix Technologies, LTD Product Make: MS-7142 AC Power Status: OnLine BIOS Info: AT/AT COMPATIBLE | 01/18/06 | VIAK8M - 42302e31 Motherboard: MICRO-STAR INTERNATIONAL CO., LTD MS-7142 Modem: ZTE USB Modem FFFE CDMA #2

    Read the article

  • "The system time has changed" avents after waking from sleep

    - by Damir Arh
    Sometimes when my computer running Windows 7 wakes up from sleep, it has to adjust the time. When this happens the following system event is logged: <Event xmlns='http://schemas.microsoft.com/win/2004/08/events/event'> <System> <Provider Name='Microsoft-Windows-Kernel-General' Guid='{A68CA8B7-004F-D7B6-A698-07E2DE0F1F5D}'/> <EventID>1</EventID> <Version>0</Version> <Level>4</Level> <Task>0</Task> <Opcode>0</Opcode> <Keywords>0x8000000000000010</Keywords> <TimeCreated SystemTime='2010-03-06T19:09:57.500000000Z'/> <EventRecordID>10672</EventRecordID> <Correlation/> <Execution ProcessID='4' ThreadID='56'/> <Channel>System</Channel> <Computer>GAME</Computer> <Security/> </System> <EventData> <Data Name='NewTime'>2010-03-06T19:09:57.500000000Z</Data> <Data Name='OldTime'>2010-03-06T17:34:32.870117200Z</Data> </EventData> <RenderingInfo Culture='sl-SI'> <Message>The system time has changed to ?2010?-?03?-?06T19:09:57.500000000Z from ?2010?-?03?-?06T17:34:32.870117200Z.</Message> <Level>Information</Level> <Task></Task> <Opcode>Info</Opcode> <Channel>System</Channel> <Provider>Microsoft-Windows-Kernel-General</Provider> <Keywords> <Keyword>Time</Keyword> </Keywords> </RenderingInfo> </Event> When this happens (I noticed it twice until now) the old time always corresponds to the time when computer entered sleep. The problem is that if Windows Media Center is scheduled for recording during this time, it just skips it as if the computer was turned off. I never had this problem running Windows Vista on the same machine. Any ideas what could be causing this problem and how to solve it are welcome.

    Read the article

  • How do I fix this Windows 7 wireless connectivity issue?

    - by Charles Randall
    I have a laptop with an Intel Wireless Centrino 6300 module. Recently, the machine has stopped properly connecting to my wireless router. It will get stuck in a loop of connecting, then disconnecting and reconnecting. While connected, it will simply say "No Internet Access." Running inSSIDer 2.0, it shows my network jumping around between two channels -- I know this isn't the case, because I've set my router to sit on one single channel. My MacBook Pro, Boxee Box, PS3, and Xbox 360 all connect fine to the wireless and have no problems at all. I know it's not the wireless module, as I bought a second one recently assuming the first had died -- but I get the same behavior with both. Sometimes, I can fix the issue temporarily by deleting the network (Using the Manage Wireless Networks page), and then re-adding it (via standard wireless methods). Then it will work for a few days. But inevitably the problem comes back, and now the laptop simply won't connect to the wireless at all, even if I take steps that usually work. Since I've ruled out the hardware, and it's unlikely some kind of interference issue (because I would expect to see it on any multitude of other devices), I would think at this point that it's a problem with Windows itself. One thing that might be a hint, even though I delete the network, when I add it again, it's always listed as "Wireless Network Connection 2" even though there isn't another in the list.

    Read the article

< Previous Page | 326 327 328 329 330 331 332 333 334 335 336 337  | Next Page >