Search Results

Search found 13880 results on 556 pages for 'explicit interface'.

Page 333/556 | < Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >

• Why can't I access the WebUI of my DNS-323 NAS after a firmware upgrade?

  - by anonymous2

  Hi Everyone, I just bought a D-Link DNS-323 NAS Enclosure, and have run into a problem. I read that the firmware that had shipped with (1.07) did not support 2TB drives, so I downloaded firmware 1.08. Turned on the device for thwe first time and went straight to the WebUI (everything looked/worked fine) Proceeded with the firmware update, completed successfully. Rebooted and I cannot access the WebUI. I can see the NAS connected via my router interface I can also ping the ip adress assigned, but I cannot access the WebUI or find it via D-Link easy search software. I have tried the factory reset button, but that does not seem to be doing anything, the square blue light just keeps flashing from the moment the unit is powered on, whether I press the reset button or not, and the symptoms remain the same... PS. I did/do not have any drives installed yet. Please help?

  Read the article

• Installed Windows 7 without formatting disk? Possible?

  - by ile

  I've just installed Win7 but I'm little confused. When booting from XP cd, there is an option to format hard drive. After choosing which partition to format, format process takes usually not less than hour (depends on size of partition), but when I clicked on Format when in Windows 7 installation interface, I received some message (I cant remember what was it, but it was not any error message or something like that) and that was it. After that I choose to install Windows 7 and installation began. "Expanding Windows Files" was the longest process of installation. Was that the part when the hard drive was formatted? I don't understand what happened? Is it possible that my hard drive was not formatted but still installation was successful?

  Read the article

• Xorg fails to start under Ubuntu

  - by den-javamaniac

  I'm running desktop Ubuntu 9.10 on my Dell laptop. Previously it was Ubuntu 9.04. After some period of time (lets say 3-4 months) my X fails to start automatically after some restart calls. If that takes place my network manager applet doesn't start either (after I do startx). Can any one point out what I'm missing/what's the problem? EDDITED I get a perfect server boot meaning there's no Xorg started. Command line interface is all I get starting from login and further.

  Read the article

• Xorg fails to start under Ubuntu

  - by den-javamaniac

  I'm running desktop Ubuntu 9.10 on my Dell laptop. Previously it was Ubuntu 9.04. After some period of time (lets say 3-4 months) my X fails to start automatically after some restart calls. If that takes place my network manager applet doesn't start either (after I do startx). Can any one point out what I'm missing/what's the problem? EDDITED I get a perfect server boot meaning there's no Xorg started. Command line interface is all I get starting from login and further.

  Read the article

• forward same port but for two different IPs (cisco)

  - by Colin

  Hi! I have a cisco running IOS 12.0(25) responding to two different IPs addresses: IP_A and IP_B. Behind this router I also have two different servers: server_A and server_B. What I want is to forward port 22 to both servers, so: IP_A, port22 -> server_A, port22 IP_B, port22 -> server_B, port22 ATM this only works for one of them (server_A), this is my config: interface Ethernet0/0 description Internet ip address IP_A 255.255.255.0 ip address IP_B 255.255.255.0 secondary no ip directed-broadcast ip nat outside no ip mroute-cache no cdp enable ip nat pool pool_A IP_A IP_A netmask 255.255.255.0 ip nat pool pool_B IP_B IP_B netmask 255.255.255.0 ip nat inside source list A pool pool_A overload ip nat inside source list B pool pool_B overload ip nat inside source static tcp server_B 22 IP_B 22 extendable ip nat inside source static tcp server_A 22 IP_A 22 extendable access-list A permit server_A access-list B permit server_B

  Read the article

• cannot using internet in VMWare

  - by user66247

  I am using VMware Workstation version 7 on Ubuntu 10.10. I installed Windows XP service pack 3 for guest os. Within VMWare, I am using bridge connection that I assigned static IP address to be able to ping host IP address but I cannot ping default router gateway. I also tried to command "/etc/init.d/vmware start" on terminal. All tasks are able to start successfully except "VM communication interface socket family" I am not sure that how to setup network for my VMWare by using wireless. Thanks in advance.

  Read the article

• Facing difficulty with migrating from wordpress to Drupal

  - by rakibtg

  One of my blog was build of Wordpress but now i want to use Drupal as the CMS of my Blog. To do so I have deleted all the Wordpress files from my server and the Database and MySQL user which are associated with wordpress blog and uploaded the Drupal files in my server directory where the wordpress files were. But, when i have opened the blog it shows the Wordpress blog! though its been deleted and their should be the Drupal Installation interface. So, i have re-checked my server directories and database, there is not wordpress files and wp database all are deleted, there is only the drupal files, but when i go to the blog to install drupal there is still the Wordpress blog, I have checked the blog in many web browsers and there is not cache memory problem. My hosting server is linux based. can't understand what to do? Any idea? Thanks

  Read the article

• Safe to use high port numbers? (re: obscuring web services)

  - by sofakng

  I have a small home network and I'm trying to balance the need for security versus convenience. The safest way to secure internal web servers is to only connect using VPNs but this seems overkill to protect a DVRs remote web interface (for example). As a compromise, would it be better to use very large ports numbers? (eg. five digits up to 65531) I've read that port scanners typically only scan the first 10,000 ports so using very high port numbers is a bit more secure. Is this true? Are there better ways to protect web servers? (ie. web guis for applications)

  Read the article

• How feasible is it to setup a FreeNAS to be more like a full install of FreeBSD

  - by mmccoo

  So I've been playing with FreeNAS over the last week, finally trying to get my act together and store my important files properly. I'm finding myself wanting to install and compile additional packages. pkg_add has been great for some things, but it appears that my install is rather crippled. make is missing. I installed gmake and linked make to that. math.h is missing as is sys/cdefs.h I thought these are part of any core unix/linux system? cc is missing though I've installed gcc45. I'm used to having just gcc. Sure I can create a link, but I'm not sure this is the proper thing to do. perl installed fine, but I can't add stuff with cpan. This is how I discovered 1,2, and 3. So my question is this: do I just need to bite the bullet and install a full FreeBSD? The web interface to FreeNAS is kinda nice

  Read the article

• Route gaming data over wireless and everything else through LAN?

  - by Alex

  I have two internet connections available to me. One is via LAN.. not a great ping, but fast downloads. The other is via USB wireless adapter.. good ping, but slow downloads. I want to connect to both of them simultaneously. I want to be able to specify which data or application will use the wireless connection and route everything else through the lan connection. Is this possible, and how would I do it? Windows 7 x64 is my operating system. Here is the data from route print: http://pastebin.com/vsjQRpSM I'm still unsure of how to use this to make all of my data go through the nvidia lan interface, even after reading route /? Also, if I'm able to achieve that, will it override the ForceBindIP?

  Read the article

• Safe to use high port numbers? (re: obscuring web services)

  - by sofakng

  I have a small home network and I'm trying to balance the need for security versus convenience. The safest way to secure internal web servers is to only connect using VPNs but this seems overkill to protect a DVRs remote web interface (for example). As a compromise, would it be better to use very large ports numbers? (eg. five digits up to 65531) I've read that port scanners typically only scan the first 10,000 ports so using very high port numbers is a bit more secure. Is this true? Are there better ways to protect web servers? (ie. web guis for applications)

  Read the article

• Linux clients for Exchange (email and) calendar

  - by jplindstrom

  At $work, the official email solution is Outlook on Windows, connected to an Exchange server. That's problematic for people with Linux on their desktop machine. The Exchange server supports IMAP, and e-mail works fairly well using the usual suspects, e.g. Thunderbird. It also provides the web mail interface, which is fairly crap unless you use IE. (Any other favorite e-mail clients?) The biggest problem is the Outlook Calendar. I still have found no viable Linux client that can replace it. Any recommendations?

  Read the article

• Mail.app slow to include new messages

  - by Chris Tompsett

  With Leopard I was able to link to the University's Exchange 2003 server with and IMAP connection and mail out directly vie the SMTP client. With Snow Leopard I attempted to update to a full Exchange service (Exchange 2007). Almost all has worked OK (ical, address, etc.) except that new mail posted to my email account, which is visible using a 'web' interface to Exchange remains invisible for some random number of hours. Those who are running the Exchange server have no interest in discussing the problem. Has anyone else had a similar experience?

  Read the article

• Port forwarding using IP Tables

  - by Darider

  I have a server with a LAN facing address of 192.168.5.100 (eth0) and another LAN facing address of 192.168.6.6 (eth1). On this server I have a Virtualbox instance of fedora running an apache webserver (on port 8080) with a bridged interface to eth1 on the host server with address of 192.168.6.7 Users on the 192.168.6.x network can access the Webserver on the Vbox instance (192.168.6.7) with no problems. My question is what kind of iptables entries or commands should be made/executed so as to allow for users on the 192.168.5.x network to access the webserver on the vbox instance. (I'm hoping their url can be something like: http://192.168.5.100:8080)

  Read the article

• Cisco 1760 T1 Setup

  - by Joseph

  My 1760 has a WIC1-T1 card in Slot 0 and the slot 0 "OK" light is lit. When the router boots it shows that it sees the T1 card. I would like to configure my T1. I received the following details from my ISP: * Removed IP's IP Version: IPv4 Router Interface: edge1.mia1 -- t1-2/1/0:2:13 -- Switch Port: Vlan: WAN Network: 4.59.?.?/30 Level3 Side: 4.59.?.? Customer Side: 4.59.?.? Cust. LAN IPs: 4.59.?.?/27 The problem is that it is not listed under interfaces. I am a noob with IOS, please let me know if you need more details. Thanks.

  Read the article

• How to backup data from linux servers to linux server (incremental + snapshot)?

  - by wag2639

  We have a handful of hosted servers running RHEL4 and RHEL5 and would like to backup some key folders (I'm thinking /var /srv and /etc) to a local server we have in house. The local server is running Ubuntu 9.10 Server edition. I'm looking for a free (preferably OSS) way to grab (or push) incremental backups to my local server and once a month or so, make a new snapshot for incremental updates in between snapshots. Also, while I'm comfortable with using a command line, others may need to use the system in the future, and I would like some kind of graphical or web interface to browse the backup repository. Suggestions?

  Read the article

• How to backup data from linux servers to linux server (incremental + snapshot)?

  - by wag2639

  We have a handful of hosted servers running RHEL4 and RHEL5 and would like to backup some key folders (I'm thinking /var /srv and /etc) to a local server we have in house. The local server is running Ubuntu 9.10 Server edition. I'm looking for a free (preferably OSS) way to grab (or push) incremental backups to my local server and once a month or so, make a new snapshot for incremental updates in between snapshots. Also, while I'm comfortable with using a command line, others may need to use the system in the future, and I would like some kind of graphical or web interface to browse the backup repository. Suggestions?

  Read the article

• Combine VPN bandwith over two or more WAN connections? Load balancing?

  - by mistrfu

  Imagine you only have DSL with 5mbps Down and 2mbps Up. Is it possible to have 10 of these for example and combine them in a way that would increase the upstrean bandwidth to one server? In my head it works like this: intranet with one gateway/router router connected to multi wan load ballancer on each ballancer wan port router with vpn clinet set up, tunneling to a server ?some? software on the server in cloud joining all these connection into one interface again I would need this mostly for big uploads to a server, downlink to the office is not that important at all. Does it even make sense? I drew an image to clarify.

  Read the article

• What are the methods of separating network spaces in a LAN?

  - by dash17291

  Please detail me the methods. My thoughts: put the servers in separate (sub)networks the servers are forced to go through the firewall but no NAT is required assign more IP addresses to the internal interface of the server choosing gateway addresses from the clients and servers IP address ranges split DNS Netfilter/{iptables, ipset} could be heavily involved, I'm talking about Linux servers. See for example: Destination NAT Onto the Same Network from internal clients Please do not explain what is NAT or DNS. This is a theoretical question, but my poor English knowledge prevent me to describe it in a fancy fashion.

  Read the article

• Change ip route metric

  - by notphunny

  I'm constantly switching between eth0 and wlan0 interface on my archlinux because I often change OpenWrt fw images on my second router (which isn't connected anywhere). So I have problem with my routes when I'm connected to my wlan and want to connect with Ethernet to my router. Both routers are on 192.168.1.1/24 and after connecting to my Ethernet profile eth0 route becomes default one (which is ok for the time), because of smaller metric I guess. So I'm interested, how can I change routes metric so my applications can be connected to the internet (through out wlan)? Maybe there is solution not to use Default Gateway on Ethernet profile, however I still want to know how to change metric. Or default route if there are more then one.

  Read the article

• How to secure a new server OS installation

  - by Pat R Ellery

  I bought (and just received) a new 1u dell poweredge 860 (got it on ebay for $35). I finished installing Ubuntu Server (Ubuntu Server 12.04.3 LTS), install apache/mariadb/memcache/php5 works great but I am scared about security. so far I am the only one using the server but eventually more people (friends, friends of friends) will use this server, use ssh etc... I want to know what can I do to secure all the information and not get hacked, both from the web or ssh or ddos and any other attack possible. Does Ubuntu Server does it for you right away? or I have to fix it my self? Thank you EDIT: I installed (so far): All dev tools ssh server LAMP I didn't install: Graphical interface

  Read the article

• Connecting to a 2.5" laptop drive using USB

  - by user27449

  So I swapped my MBP hard drive with a SSD drive, and I want to connect to my old hard drive. I bought a nextstar 3 external 2.5" drive enclosure that has a USB 2.0 interface. I watched an online video of an older version of the enclosure, and in the video they had a ATA cable to connect to the drive. My enclosure didn't come with anything like that, and there doesn't seem to be a way to connect to my drive (my old drive is a seagate 500gb momentus 7200 RPM). My laptop is about 2 years old now (MBP 17"). The drive doesnt' have pins to connect, it has a wide plug type connector, and a USB connector also (I was able to directly plugin the USB cable to the drive, but didn't connect it to my computer, was just testing thigns out). Is it safe for me to directly connect the cable that came with the enclosure to the drive, and then connect the other end to my computer? Does this single cable provide power and data transfer?

  Read the article

• How to attach multiple ipv6 ips to eth1 on debian

  - by Noodles

  I've just got a new server with native ipv6. I want to attach multiple ipv6 ips to eth1, but the only way I can see to do so is to attach them individually: i.e. address 2607:f0d0:xxxx:xxxx::2 address 2607:f0d0:xxxx:xxxx::3 address 2607:f0d0:xxxx:xxxx::4 Is it possible to bind whole subnets of ipv6 to a single network interface on debian? My server host tells me I have 18,446,744,073,709,551,616 ipv6 addresses for that server, surely it gets to be a nightmare to manage if they all have to bound individually (plus ifconfig would look messy). Does anyone have a solution?

  Read the article

• Unable to connect to vrde virtualbox VM remotely

  - by b1ackjosh

  So I've remotely created my first headless using ssh. Now I'm attempting to connect to this VM using RDP so I can install Ubuntu Server, but I cannot get connected at all. When starting the VM everything appears fine: $ vboxheadless -s WebTesting Oracle VM VirtualBox Headless Interface 4.0.16 (C) 2008-2012 Oracle Corporation All rights reserved. VRDE server is listening on port 4455. And showvminfo shows: VRDE: enabled (Address 0.0.0.0, Ports 4455, MultiConn: off, ReuseSingleConn: off, Authentication type: null) However I'm still prompted with the "enter your credentials" screen every time I attempt to connect. From reading the documentation null shouldn't prompt me with this screen at all... Any help with this is greatly appreciated. P.S. I am using ssh tunneling in putty to tunnel in to my network.

  Read the article

• Can I set up two NICs bridged together and still SSH into the bridging machine?

  - by squinlan

  I have a ubuntu box setup with two NICs. I can bridge them together just fine, but I haven't been able to setup a way to SSH into the box once the connections are bridged together. Here's my /etc/network/interfaces: auto lo iface lo inet loopback auto eth1 iface eth1 inet manual auto eth0 iface eth0 inet manual auto br0 iface br0 inet static address 192.168.33.213 netmask 255.255.255.0 gateway 192.168.33.1 bridge_ports eth0 eth1 bridge_stp off bridge_fd 0 bridge_maxwait 0 This works just fine for bridging, but I'm not able to SSH into the box. I tried setting up another interface on one of the NICs: auto eth0:1 iface eth0:1 inet static address 192.168.33.215 netmask 255.255.255.0 gateway 192.168.33.1 But this really didn't help. Is it possible to ssh into a machine that has all of its NICs bridged? If it is, how?

  Read the article

< Previous Page | 329 330 331 332 333 334 335 336 337 338 339 340  | Next Page >