Search Results

Search found 11365 results on 455 pages for 'authorization basic'.

Page 337/455 | < Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

• Configure linux machine as bridge/switch and end device

  - by leemes

  At my home, I have two desktop PCs in two rooms. The router / DSL modem is in one of these rooms. Now I want to configure a home server (having 2 LAN ports, running 24/7) in the corridor between the two rooms, using only one LAN cable at each door. This gives me the following physical configuration: (door) (door) .----/-/----. .-----/-/----------._ FritzBox | | | .----´´ DSL Router PC1 Server | PC2 As just said, the server has 2 network interfaces and is running Ubuntu. What I need now is a network configuration which enables both the server and PC1 to connect to the router. I think the server needs to serve as a bridge or switch. Currently, all computers are configured having static IP addresses. If I'm understanding it correctly, a bridge / switch doesn't have its own IP address, but as the server needs to be configured as an own end device, it needs to have one. My first question is, do I have to configure both interfaces separately, giving both the same static IP address? My next question is, how do I bridge the two physical networks into one? I have basic understanding (but am always confused again and again) of bridges and switches, but I don't know how to configure it in software. I only know that it's possible to do so :) The third question is: Is it possible to configure this in a way that network packets from/to PC1 to/from the router only go through hardware or only consume low CPU in the server? Can you help me? Thanks in advance!

  Read the article

• Google Drive terminates without error on startup

  - by Iszi

  I've used Google Drive for awhile now, but it won't start up after installing on my latest system re-build. I'm still using the same OS, hardware, and basic software load (antivirus, firewall, etc.) that I have for years during which I had not previously had problems with Drive. OS: Windows 7 Ultimate x64 Google Drive Version: 1.12.5329.1887 Now, whenever I try to run Google Drive, it just spawns two instances of the executable which die shortly after. No error messages are posted to the desktop, and nothing indicating any problem is written to the Event Log. After some research, I've yet to find anyone having the same problem who's found an answer. I did find out how to run Google Drive in diagnostic mode, using the --vv parameter at the command line. After that, I opened up the sync log and got this: 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 OS: Windows/6.1.7601-SP1 2013-10-31 17:11:24,039 INFO pid=3664 1892:MainThread logging:1600 Google Drive (build 1.12.5329.1887) 2013-10-31 17:11:24,039 DEBUG pid=3664 1892:MainThread logging:1608 DEBUGGING DUMP is ON. 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 ERROR, UNEXPECTED EXCEPTION 2013-10-31 17:11:24,051 ERROR pid=3664 1892:MainThread logging:1575 [Error 5] Access is denied Traceback (most recent call last): File "<string>", line 232, in Main File "<string>", line 118, in RegisterCustomFileTypes File "P:\p\agents\hpal4.eem\recipes\353983091\base\b\drb\googleclient\apps\webdrive_sync\windows\build\pyi.win32\main\outPYZ1.pyz/windows.registry", line 62, in GetValue WindowsError: [Error 5] Access is denied 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Crash reporting disabled. Ignoring report. 2013-10-31 17:11:24,052 INFO pid=3664 1892:MainThread logging:1600 Exiting with error code: 0 I'm running on an account with Administrator-level permissions, and have even tried using "Run As Administrator" on the EXE. I'm not sure why it's looking for a P:\ drive, as no such volume has ever been mounted on this system. What should I do to try to further troubleshoot, and resolve, this issue?

  Read the article

• Can I share my cable internet connection through my ADSL wireless router?

  - by Roaders

  Hi All Over the xmas period I am at my in-laws. They have Virgin Broadband (cable) and have a basic modem / router that is plugged directly into their computer using an ethernet cable. My wife and I arrived with 5 PCs! (ok, one is a gift and won't be used) 4 of which are laptops so I would like to be able to use their internet connection. At the moment I am working so have plugged the ethernet cable into my work laptop. Rebooting the router meant that my work laptop now has internet. I have my ADSL Netgear router which is wireless. I tried plugging it in between the router and the PC but I didn't seem to be able to share the internet connection wirelessly. The original PC still had internet despite ony being connected to my router but my wireless laptop didn't have a connection. My old cable router had an internet ethernet port on the back that the modem plugged into. My ADSL router doesn't, it has a phone connection socket. Is there a way of doing what I want with the equipment I have? Thanks

  Read the article

• Aging SBS needs updates / Thoughts for one-off, off-line complete backup?

  - by tcv

  Hey guys, So, we checked out the status of an SBS 2003 at one of our more recent, spend-averse clients and found it to be woefully out-of-date. Scary out of date. I think it's running IE2. Ok, maybe not that far back. Anyway, I was thinking that I could use some kind of disk-imaging software to image the four IDE drives within and, in the event the server gets some kind of Update Induced Indigestion, I could completely restore. Usually my go-to software for this is Acronis, but my client will likely balk at a $500 price tag for a one-off backup with their server product. I had thought we could use the boot media from, say, Backup & Recovery 10 to take an off-line image of all the drives. According to their CHAT tech support, however, it will not work. I pressed for the technical reasons and they said they'd email me. They haven't emailed me. They still might. This server is running SBS 2003, pre sp2. It's got four IDE disks. One is a Basic disk, which contains the O/S. The others are bound as a dynamic disk. You might ask: "Don't they already have backup software?" They do! Backup Exec, a very low-end version that won't even do VSS. I don't know much about BE, but it seems to me that if the worst were to happen, it would mean building a new server O/S, installing BE (if the media is available), then restoring. Would it even work? I can take the system down for hours to do a backup and my goal here is a pretty dead-simple restore if the worst happens. Any and all suggestions are exciting. m

  Read the article

• MS Excel and Access - which is better for reports?

  - by Nat

  Where I work, staff have just started to use a basic table in excel (1 october) to record sales which has about 10 columns (name, client, renewed, discount, paid etc). I record the data (total sold etc) every hour and email it to the manager. Each staff has the their own file on the network which they use constantly for that day (eg. John 08-10.xlsx; John 09-10.xlsx etc) and have been told to save the file after they complete a row with client data. I can see the file (in read only mode) to update the report but I am sure there must be a way of doing an autoupdate of their worksheets in real time. I can link worksheets and workbooks to my main workbook but manually. Does anyone have suggestions on have to do this on Excel? Or would Access allow me to make a report which shows the sales total for that hour without the staff closing the file or constantly clicking save every few minutes? We use office 2010. thanks

  Read the article

• Php5-fpm Crash if much visitors

  - by chillah

  I decided to change my OP to Nginx from Litespeed because i read much about the low resource that Nginx would cost. Im running a Wordpress site with 500 users online My www.conf in "/etc/php5/fpm/pool.d" pm.max_children = 200 pm.start_servers = 20 pm.min_spare_servers = 20 pm.max_spare_servers = 60 ;pm.process_idle_timeout = 10s; ;pm.max_requests = 1000 Since i changed that config to higher requests and more children the Site needs longer till it shows me a White blank page. If i restart the php5-fpm prozess then, the site is running fine again. The CPU usage is at 5% if the php5-fpm is crashed and if its running its about 20 to 90%! Heres my Nginx.conf: user www-data; worker_processes 2; pid /var/run/nginx.pid; events { worker_connections 3048; # multi_accept on; } http { ## # Basic Settings ## sendfile on; tcp_nopush on; tcp_nodelay on; keepalive_timeout 65; types_hash_max_size 2048; # server_tokens off; I already tried changing the settings, tryed all variants but nothing worked. The Mashine: Dualcore 4gb ram

  Read the article

• How to secure an Internet-facing Elastic Search implementation in a shared hosting environment?

  - by casperOne

  (Originally asked on StackOverflow, and recommended that I move it here) I've been going over the documentation for Elastic Search and I'm a big fan and I'd like to use it to handle the search for my ASP.NET MVC app. That introduces a few interesting twists, however. If the ASP.NET MVC application was on a dedicated machine, it would be simple to spool up an instance of Elastic Search and use the TCP Transport to connect locally. However, I'm not on a dedicated machine for the ASP.NET MVC application, nor does it look like I'll move to one anytime soon. That leaves hosting Elastic Search on another machine (in the *NIX world) and I would probably go with shared hosting there. One of the biggest things lacking from Elastic Search, however, is the fact that it doesn't support HTTPS and basic authentication out of the box. If it did, then this question wouldn't exist; I'd simply host it somewhere and make sure to have an incredibly secure password and HTTPS enabled (possibly with a self-signed certificate). But that's not the case. That given, what is a good way to expose Elastic Search over the Internet in a secure way? Note, I'm looking for something that hopefully, will not require writing code to provide shims for the methods that I want (in other words, writing forwarders).

  Read the article

• Ubuntu 8.04 wont reboot from script

  - by Littlejon

  I have a script that is run to backup a server via Rsync, after that script is run I want the server to reboot. My script is run as root from the Crontab at 3am in the morning. #!/bin/bash HOST="email" RSYNC_OPTS="-a -v -v --progress --stats --delete" RSYNC_DEST="10.0.0.10::$HOST" BACKUP_LIST="/etc /home /root" TIMESTAMP="/timestamp-bkup-start.chk" TIMESTAMP2="/timestamp-bkup-stop.chk" touch $TIMESTAMP rsync $RSYNC_OPTS $TIMESTAMP $RSYNC_DEST for BACKUP_ITEM in $BACKUP_LIST; do rsync $RSYNC_OPTS $BACKUP_ITEM $RSYNC_DEST done /etc/init.d/zimbra stop sleep 60s rsync $RSYNC_OPTS /opt $RSYNC_DEST touch $TIMESTAMP2 rsync $RSYNC_OPTS $TIMESTAMP2 $RSYNC_DEST echo `date +%Y%m%d%H%M` >> /var/log/reset reboot # $# shows number of args passed # $1 to access first variable #if [ $# -eq 1 ]; then # if [ $1 = "withreboot" ]; then # echo "rebooting..."; # echo `date +%Y%m%d%H%M` >> /var/log/reset # /sbin/reboot # fi #fi I have tried using init 6 rather then reboot. I have tried /sbin/reboot. I also have another basic script that just echos to the reset log and runs reboot without issue. It is just with the script above the server wont restart. If anyone has any theories that would be great as I have run out of idea. Thanks, Jon

  Read the article

• Computer freezing while watching Flash videos from net

  - by t3st

  I have a Windows 7 home basic, while watching videos from net (within 5 minutes) computer starts to freeze and shows 100 percent CPU usage. I first thought it's a browser issue but watching videos from different browsers also has the same issue. My system runs the latest Firefox browser and all my plugins (including Flash) is up-to-date. After this when I shutdown/restart the computer it will go to the login window with out any problem. From there when I tried to log in to any account, the system starts to freeze and again I have to start and run Windows in safe mode (which doesn't show any problem). I read it in an article to do these steps CMD->sfc/scannow chkdsk after that only my system works normally, even now I can't watch any videos on the net otherwise it starts freezing( I can watch downloaded videos in computer without a problem) and have to do the whole process once more (which takes a lot of time). while running sfc/scannow its showed results that some of the files are corrupted and it could not be repaired. Can this be the cause for freezing of my computer while running Flash videos? or is it a hardware related problem? What different steps do I have to take to correct those corrupt files? System restore works only some times.

  Read the article

• Windows 2008 R2 file share - any way to "lock it down" outside of a 3rd party app?

  - by TheCleaner

  I have a 3rd party app that "makes a call" to write files to a file share on our network using the currently logged in credentials of the Windows domain user. Meaning the 3rd party app doesn't pass the apps credentials but simply issues a behind the scenes copy command to take a source file specified and copy/move it to the destination "repository" on the file share. The basic premise is that it keeps revisions/approvals for Document Control (think svn/git I guess, similar to this question: Lock down Windows folder to only be updatable by SVN). This all works fine...but here's my issue: I need a way to lock down the file share from being accessed/modified outside of using the 3rd party app (meaning prevent explorer/word/excel/etc from getting to that share). I know I can do the following: make the share a hidden share ($) - this definitely helps. Most users would have zero clue on how to get to such a share. Solves probably 95% of my issue. go one step further and set the "Hidden" attribute on the folders in the hidden share - this would go a little further in that even if a user knows the path to the hidden share like \\server\hidden$ they still won't see folders in that share without changing their explorer options to "show hidden files/folder Any other ideas on how I can lock this down? The users still need modify rights to this share/folders since the 3rd party app relies on their Windows permissions to that location when copying the files into it. I can't really use 3rd party tools to password protect the folder/share without causing the 3rd party app functions to fail.

  Read the article

• Why did you start with Linux ? And why did you continue using it ?

  - by Stefano Borini

  I'd like to know the reasons that moved you towards Linux. Personally, I started because we had to use a Digital for the Fortran 77 exercises during my first year at the university. Linux was installed on many university computers, and I got interested in it. I always liked to code (on the C64) in basic and assembler, but I knew nothing about other languages. I soon discovered a chat engine called NUTS, and the idea of becoming proficient in C appealed me, so I started hacking the code. To do so, I needed a Unix at home, so I bought a Slackware 3.4 and installed it on my Pentium 166. I then continued using it for many years, reason being that I had pleasure in learning new things and the openness of information about the internals. It was a great learning platform. I then moved to osx because I enjoy the power of Unix with the beauty and efficiency of its interface. I am interested in your answer because I believe that the panorama has changed somehow. Although I still guess to find many "hackers" interested in Linux for the sake of knowledge, I also believe that there are other reasons (work, friends, bought a netbook).

  Read the article

• Find routers IP address on the other side

  - by corsiKa

  Here's the basic setup of my network In this diagram: 1: The internet c: cable 2: Wireless router w: wireless connection 3: A win7 box with internet connection sharing enabled 4: A wireless router, but I'm only using its LAN capabilities to connect box 5 to the internet. 5: A win7 box, the computer I'm using to make this post. So its internet works just fine. Now if I'm on box 5, and I ping 192.168.1.1, I hit 4. If I'm on box 3 and I ping 192.168.1.1, I hit 2. Now obviously box 3 does not think 4's IP address is 192.168.1.1, or I wouldn't be able to connect to the internet. Okay, now that you know as much as I do about my network, here's my question: If I was on box 3, how would I determine the IP address of 4? Basically I'm running a webserver on box 5 and want to access this webserver on box 3 and other boxes. So that's the end goal. If there's other information there that can help, I'd appreciate it. Thanks!

  Read the article

• Can Dovecot IMAP automatically create Maildir folders for new (virtual) users?

  - by user233441

  everyone. I am learning to set up a dovecot home IMAP server using a virtual Ubuntu 12.04 machine. My intention is eventually to have a home server that uses POP3 to take email from several addresses and remove them from my ISP's servers, while making them accessible through a home IMAP server (this is similar to the setup described at https://help.ubuntu.com/community/POP3Aggregator, which explains how to set up the system with dovecot version 1, and is thus outdated). I intend to use the ISP's server directly when sending messages, and to BCC all sent messages to myself. I've completed the basic set up of the test server: getmail uses POP3 to fetch messages from two test email accounts, and successfully delivers them to the respective Maildir-style new folders on the virtual machine. Dovecot then successfully sees these messages. I have two questions: 1) I had to set up new, cur, and tmp folders for both of the test accounts manually to get this setup to work. Is there a way to get dovecot to create these Maildir folders automatically when I create a new virtual user account (e.g., when I add a user and password combination to my dovecot password file), or is it expected that I write a bash script to automate that task? 2) I would welcome any comments you have on how this approach could be improved as I learn to set it up. My motivations with this approach are 1) to enable archiving/storing emails from several hosting providers that impose a cap on server storage, and 2) to give me somewhat greater control over email storage without requiring that I set up and administrate a mail server from scratch (which I'm not yet prepared to do) (this follows the recommendations at https://ssd.eff.org/tech/email). Thank you!

  Read the article

• Microsoft Mouse and Keyboard Center - Slow response for App-specific shortcuts

  - by Darrel Hoffman

  So a few months ago, I bought a new MS mouse, and was surprised that they'd discontinued Intellipoint in favor of this Microsoft Mouse and Keyboard Center. It seems to have the same functionality underneath all the bloat, but there's a very serious drawback - when I set up application-specific functions for the extra buttons on the mouse, they work, but sometimes with a very long delay, like up to a minute or more. For example, I often set up the left side button as an "Undo" in various programs for convenience. But sometimes, when I try to use that Undo button, nothing happens, so I'm forced to use the standard Ctrl-Z or whatever. But then, a minute or so later, it suddenly remembers that I hit that button a while back, and calls the Undo unexpectedly on something entirely different. It's infuriating. No modern computer function should be this slow. It's not the software or the computer itself, because doing an Undo via Ctrl-Z or the menu still works instantly. It's very definitely a side-effect of delayed response to the mouse button. Usually after it delays the first time, it'll work quickly after that, but if you haven't used a given shortcut in several minutes, it "forgets" again and you get another inexplicably long delay. Intellipoint never had this problem, but it's not supported any more, and not compatible with the newer mice. Has anyone else noticed slow-downs with MS M&K C and app-specific shortcuts? Any ideas how to get around this? I use these shortcuts extensively in my workflow and it's just entirely unacceptable to have such a long delay in what should be a pretty basic feature.

  Read the article

• What's a good solution for file-tagging in linux?

  - by julien

  I've been looking for a way to tag my files and search/filter them based on those tags. Here are my (updated) requirements : any file readable by the user can be tagged freely a user can search for files matching one or several tags files can be moved around without losing the previously associated tags the system could be backed up easily no dependencies on any desktop environment if any gui is involved, there must be a cli fallback I've been hoping for some basic filesystem & coreutils hackery to handle this, but I haven' thought about this hard enough yet. Meanwhile I'll review beagle and metatracker, which have been mentionned here, and see how they perform. Ok so beagle has huge gnome dependencies, and tracker is okish, but still has some dependencies I don't like... Been doing some more research, and the way to go could very well be extended file attributes. That's a native solution for most recent filesystems, but they aren't very well supported yet (most coreutils destroys them by default, cp for example needs the -a flag to preserve them). Would like to hear some thoughts on using them while I try my hand at some hacks myself, eventhough this might warrant a new question.

  Read the article

• What's the best way to get a stored POP3 password out of Outlook 2007?

  - by Tom Morris

  If you have a password for a POP3 account in Outlook 2007 (Windows 7 Home Premium) and you then forget the password, how do you retrieve it? I tried copy-and-paste. No go. I downloaded Mail PassView, but upon installing it, AVG said it was malware, so I removed it. I eventually found the account details by opening up RegEdit, and found it in HKCU\Software\Microsoft\Windows NT\CurrentVersion\Windows Messaging Subsystem\Profiles\Outlook\ (...) but it was encoded in REG_BINARY. I Googled around and found various Visual Basic routines for decoding it but being a Unix dork I had absolutely no idea what to do with said scripts. By this point, I gave up and managed to get hold of the password by another means (it was written down on a piece of paper in the briefcase of the owner of the account - I know, it makes the inner sysadmin rage). I also attempted to write a simple POP3 server in Python and then get Outlook to log on to it, but that didn't really work out (it was about 4am at that point). For future reference, is there an easy and sensible way of doing this? Is Mail PassView actually evil spyware or was AVG just giving me a false positive? (Any chance of Windows 8 having something like OS X's Keychain?)

  Read the article

• Resize a RAID 1 volume on OSX Snow Leopard - how? (Note: software raid)

  - by Emmel

  I've scoured the Internet in search of an answer to this question, and as usual with OSX-related topics, I often don't find any deep-dive technical explanations sufficient enough to feel confident doing dangerous things. Here is my question: I have a Mac Pro, running OSX 10.6.2. I have, as my main root/boot disk, a RAID 1 volume called "Mirror1". Mirror1 is comprised of two 1 TB disks. Mirror1, however, is fixed at 640 GB. That's because, I originally took a 640GB disk, bought a terabyte disk, mirrored it (using diskutil appleraid enable...), when it synced I removed the 640GB and replaced it with a second 1 TB disk, and synced again. Voila! A single 640 GB replaced by two 1 TB disks in a mirror.. Actually, no. There's still something missing from the equation: Mirror1 needs to be expanded from 640GB to 1 TB to match the partition sizes on each of those disks. How do I do this? Perhaps the diskutil output will help: -> diskutil list /dev/disk0 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk0 1: EFI 209.7 MB disk0s1 2: Apple_RAID 999.9 GB disk0s2 3: Apple_Boot Boot OSX 134.2 MB disk0s3 /dev/disk1 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *1.0 TB disk1 1: EFI 209.7 MB disk1s1 2: Apple_RAID 999.9 GB disk1s2 3: Apple_Boot Boot OSX 134.2 MB disk1s3 /dev/disk2 #: TYPE NAME SIZE IDENTIFIER 0: GUID_partition_scheme *640.1 GB disk2 1: EFI 209.7 MB disk2s1 2: Apple_HFS Mac Disk 2 536.7 GB disk2s2 3: Microsoft Basic Data BOOTCAMP 103.1 GB disk2s3 /dev/disk3 #: TYPE NAME SIZE IDENTIFIER 0: Apple_HFS Mirror1 *639.8 GB disk3 -> diskutil appleraid list AppleRAID sets (1 found) =============================================================================== Name: Macintosh HD Unique ID: 1953F864-B474-4EB6-8E69-41834EBD0247 Type: Mirror Status: Online Size: 639.8 GB (639791038464 Bytes) Rebuild: manual Device Node: disk3 ------------------------------------------------------------------------------- # Device Node UUID Status ------------------------------------------------------------------------------- 0 disk1s2 25109BAE-5697-40EA-B612-0217851444F7 Online 1 disk0s2 11B83AB0-8148-4DB6-8761-DEF08C855F8D Online =============================================================================== Thanks in advance.

  Read the article

• Loadbalancing with nginx and tomcat

  - by London

  Hello this should be fairly easy to answer for any system admin, the problem is that I'm not server admin but I have to complete this task, I'm very close but still not managing to do it. Here is what I mean, I have two tomcat instance running on machine1 and machine2. People usually access those by visiting urls : http://machine1:8080/appName http://machine2:9090/appName The problem is when I setup nginx with domain name i.e domain.com, nginx sends requests to http://machine1:8080/ and http://machine2:9090/ instead of http://machine1:8080/ and http://machine2:9090/appName Here is my configuration (very basic as it can be noted) : upstream backend { server machine1:8080; server machine2:9090; } server { listen 80; server_name www.mydomain.com mydomain.com; location / { # needed to forward user's IP address to rails proxy_set_header X-Real-IP $remote_addr; # needed for HTTPS proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header Host $http_host; proxy_redirect off; proxy_max_temp_file_size 0; proxy_pass http://backend; } #end location } #end server What changes must I do to do the following : - when user visits mydomain.com - transfer him to either machine1:8080/appName or machine2:9090 Thank you

  Read the article

• How to create an GUI that communicate with the USB Devices using win32 programming [migrated]

  - by VINAYAK

  I am doing my Project using win 32 programming.I am just learning about win32 programming and able to create an UI.I want to communicate with an USB Device with that UI.SO,How can i go for that?Is there any predefined functions will be there are we need to create the function for communicating with the OS and get the devices List and got the details about them. My purpose is to , 1.Creating an UI that tells about the Basic information about the device(We want to send a control request to the device to get the descriptors). 2.For that first of all i want to communicate with the OS for device attachment.That will lead to get the information about the device and Enumeration takes place and then only i request the device information through descriptors by using standard Requests. 3.And also i want to create the driver for my device.That will also need to achieve for communicating with OS(Windows). So,can anyone help me about this?How can i achieve this or approach this? Note: I am at the entry level now so anyone give response will be in a detailed format like step by step process would be appreciable.

  Read the article

• How to "drag and drop" folders or multiple HTML files into a browser and have them open in multiple tabs

  - by PoorLuzer

  I save pages that I browse on the net and find interesting into a folder called C:\PageSaves Later, during the commute, I open these pages to see what they are and move them into a neatly categorized folder tree. For example, Perl related pages goto C:\Pages\Perl, MySQL related pages goto C:\Pages\MySQL and so on. I was wondering if there is any way I could open any number of HTML files on disc / inside a folder (C:\PageSaves in my case) into Mozilla/FF/K-Meleon etc For example, I would like to just "drag and drop" the folder C:\PageSaves into FireFox and have it open all the .html pages in the folder in a separate tab Right now, if I "drag and drop" multiple HTML files, it just opens the last file in the selection. Have a set of toolbar buttons, basically, a (the) plugin that should allow me to nuke the page (if I don't want to keep the page anymore) from disc or move the file (and its corresponding folder) into a predefined / new folder I am familiar with coding full blown FireFox plugins, so even if something very basic/almost similar exists, I can take it forward. Hints/clues/other methods of achieving the same result are all welcome!

  Read the article

• VPS Memory Exchausted Even With Light Settings

  - by user101570

  Linux noob here. I have a 256MB VPS on Ubuntu 11.04 server and when I run "free -m" the result shows all memory being used (including the second line re: buffers/cache). I found this very strange, considering I only have 5 Apache processes running each chewing up about 20MB each. MYSQL is taking up 30MB. To my knowledge, and according to "top", I have no other memory hogs operating. Settings that may be relevant: PHP memory_limit = 32M MYSQL key_buffer = 16M Prefork MPM Maxclients = 10 So when I reviewed these settings, I naturally thought maxclients was too high, so I tried switching it to 5. Now not only does my memory still show as being 100% used, my website loads much, much slower, despite not getting any traffic aside from mine at the moment. I don't understand this. I thought a single Apache process handles all requests from a client received within the "KeepAliveTimeout" window, which I've set to 2 seconds. With my initial config. of 10 maxclients, my page load times are around .3ms, so a single process should handle that no problem, correct? So next I went to an extreme level of 1 for maxclients. My memory is still at 100% usage and my site loads painfully slow. I'm a noob at a complete loss here. According to the many tutorials I've read on basic server setup, I should be good to go. Help! Please! Edit: total used free shared buffers cached Mem: 256 256 0 0 0 0 -/+ buffers/cache: 256 0 Swap: 0 0 0

  Read the article

• Configuring two nearby WLANs: should I use the same ssid?

  - by Rory

  I'm configuring a home network for basic internet use (ie don't really need connectivity between workstations on the network). My brick walls mean a single wireless router doesn't provide good coverage throughout the house, so I have purchased two powerline adapters and now have the incoming modem/wireless router at one end of the house plugged into a powerline adapter, and at the other end of the house the other powerline adapter plugged into another wireless router. Currently the two wireless networks have different ssids. (The powerline adapters only do power-Ethernet; they're not wireless access points themselves.) This works well, except when I move between rooms and would ideally like my devices (iPad, phones, laptops) to switch from the weak to the strong signal. Sometimes there's enough signal that they hold on to the weak connects instead of switching to the strong one. Should I name the two networks the same ssid, and if so what is the actual effect? Do the signals get confused, is the bandwidth affected, will this help my devices seamlessly move from one to the other, or is the ssid just a cosmetic thing that actually doesn't have any impact on this situation? Are there any other settings that I should configure to make my setup optimal?

  Read the article

• Server side url scanner for malware, spyware , viruses and protect my visitors

  - by Vangel

  I have a forum/groups site that contains a lot of external URLs, sometimes direct download links. I want to protect my visitors from possible attacks from malware sites as they are mot likely to click on these links. CUrrently I implement DBL (spamhaus) but thats not enough. I want to run a background task to check the outgoing links first. I have looked at similar questions in StackOverflow (wrongly posted there) and here but fail to find a question same as mine or a good answer. People have suggested ClamAV , I don't believe it can detect Web hosted malware sites and its has a lot of missed detection. I have looked at google safe browsing service ( http://code.google.com/apis/safebrowsing/developers_guide_v2.html very complicated to implement or maintain plus midway I get lost :S ) I can go for commercial solution, anything to protect the visitors and my site brand. But I would like to hear the opinion of server admins and if anyone has implemented such a service. My Server is basic CentOS LAMP stack. thank you very much in advance.

  Read the article

• Why is only one Excel spreadsheet crippled, but others are fine?

  - by Dallas

  I have an inherited spreadsheet that I really don't want to rebuild at the moment. It's a simple small workbook that is small (< 200 rows that don't even reach to AA) and does nothing more than calculate some totals within the same worksheets. No macros, no external data sources, nothing beyond basic formatting of dates, numbers and strings. I see importing data from CSV/text has created many many workbook connections over time, but even if I delete them all (there were hundreds) it makes no difference in performance. Even clicking to simply change focus from cell to cell takes 10+ seconds, adorned by the spinning cursor and (Not Responding) appending to the title bar and the application locking up. The program seems to "recover" every time, but efficiency of editing this file is obviously seriously handicapped. All other files seem fine in Excel, and other programs have no apparent performance issues. I see Excel is chewing up CPU but I'm not sure how to narrow down what process or service is "clashing" with Excel. I tried the same file on other computers and performance is fine. If I turn off all start-up services and run only Excel, performance is restored... until I start using other programs and then it bogs down again. At this point, I would entertain almost any idea, theory or suggestion that helps pinpoint, solve or work around the issue.

  Read the article

< Previous Page | 333 334 335 336 337 338 339 340 341 342 343 344  | Next Page >