Search Results

Search found 17847 results on 714 pages for 'virtual disk'.

Page 339/714 | < Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >

• Intell SSD + Win 7 after crash can not repair, can not re install

  - by Ori

  I have Lenovo w520, after i bought it i took away old hhd (no longer with me) and replaced it with intel ssd, it worked perfectly for 1 year or so, today my system fr0ze and after waiting for some time i didi hard reset - it wasn't able to boot anymore at all, i do not see any messages from windows ever, it only loads Intel boot utility that suggests to pick one of 3 devices to boot, it has my hdd there but nothing happens. /I dont have recovery tools from lenovo since i moved to another country, i got win 7 cd from a friend (came with his laptop) abd if in bios i have AHCI - it doesnt see my ssd, if compatible mode - it sees it but format not available, partition creation gives b\me 8007045 error. I tried diskpart, in compatible mode it sees my disk but doesnt do recover or clean all, also win 7 disk tools dont do anything if i try to do boot fix... I am ok with erasing it but i seem not to be able too, i jus tneed the machine to wpork asap, all my files are on external drives so i dont care about formatting. please help! I am given a very old machine by a friend so i am able to browse internet... it is under XP...

  Read the article

• Master File Table Corrupt, any way to save data?

  - by domen

  hi. I've used search, but none of the results match my problem so I didn't have to ask separate question. I've Installed Windows 7 RTM recently and since then partitions located on one of my HDDs have gone "crazy". They used to "freeze" and didn't open in explorer for some time (minute or two, usually), sometimes all partitions of the drive wouldn't show until reboot and finally, one of those partitions started showing "disk structure is corrupted and unreadable" warning, it appeared in Disk Management window as RAW and chkdsk showed "mft corrupt". There were no important data on the partition and I didn't have enough time to analyze the problem at the moment, so I just reformatted it and ran antivirus scan on system. After that problem settled for some time, but yesterday the problematic HDD vanished again from the system. After reboot chkdsk identified mft of four partitions corrupt and now they are all in same conditions as the above mentioned one. But the difference is that the files stored in them are extremely important. and just for info: I upgraded from Win7 build 7077, but had some performance issues, so I reformatted system drive and installed fresh Win7 RTM on it. I've downloaded TestDisk and it shows all the partitions marked as NTFS (not RAW) and my knowledge of the program wasn't sufficient to obtain any other info from it :-) and the images that could help describe the problem (sorry, I'm not allowed to post images and more than one hyperlink): http:// img22.imageshack.us/img22/5909/chkdskz.jpg http:// img198.imageshack.us/img198/5576/computeray.jpg I'm interested, is there a way to let me restore the MFT or just access files so I can backup them before reformatting the drive. Thanks for your time. :) P.S. my reformatted drive is showing no problems, could there be a problem with windows 7 itself? I googled, but with no results.

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• Server slowdown

  - by Clinton Bosch

  I have a GWT application running on Tomcat on a cloud linux(Ubuntu) server, recently I released a new version of the application and suddenly my server response times have gone from 500ms average to 15s average. I have run every monitoring tool I know. iostat says my disks are 0.03% utilised mysqltuner.pl says I am OK other see below top says my processor is 99% idle and load average: 0.20, 0.31, 0.33 memory usage is 50% (-/+ buffers/cache: 3997 3974) mysqltuner output [OK] Logged in using credentials from debian maintenance account. -------- General Statistics -------------------------------------------------- [--] Skipped version check for MySQLTuner script [OK] Currently running supported MySQL version 5.1.63-0ubuntu0.10.04.1-log [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +Archive -BDB -Federated +InnoDB -ISAM -NDBCluster [--] Data in MyISAM tables: 370M (Tables: 52) [--] Data in InnoDB tables: 697M (Tables: 1749) [!!] Total fragmented tables: 1754 -------- Security Recommendations ------------------------------------------- [OK] All database users have passwords assigned -------- Performance Metrics ------------------------------------------------- [--] Up for: 19h 25m 41s (1M q [28.122 qps], 1K conn, TX: 2B, RX: 1B) [--] Reads / Writes: 98% / 2% [--] Total buffers: 1.0G global + 2.7M per thread (500 max threads) [OK] Maximum possible memory usage: 2.4G (30% of installed RAM) [OK] Slow queries: 0% (1/1M) [OK] Highest usage of available connections: 34% (173/500) [OK] Key buffer size / total MyISAM indexes: 16.0M/279.0K [OK] Key buffer hit rate: 99.9% (50K cached / 40 reads) [OK] Query cache efficiency: 61.4% (844K cached / 1M selects) [!!] Query cache prunes per day: 553779 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 34K sorts) [OK] Temporary tables created on disk: 4% (4K on disk / 102K total) [OK] Thread cache hit rate: 84% (185 created / 1K connections) [!!] Table cache hit rate: 0% (256 open / 27K opened) [OK] Open file limit used: 0% (20/2K) [OK] Table locks acquired immediately: 100% (692K immediate / 692K locks) [OK] InnoDB data size / buffer pool: 697.2M/1.0G -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Enable the slow query log to troubleshoot bad queries Increase table_cache gradually to avoid file descriptor limits Variables to adjust: query_cache_size (> 16M) table_cache (> 256)

  Read the article

• Explorer.exe hangup during move large file into external drive

  - by PiotrK

  During move large files (700mb+) to external drive formated NTFS via USB 3.0 I've noticed strange things about explorer.exe (I am using Windows 7 up to date) Sometimes after move file the explorer get stuck (ie. it can happen after few files during move of several large files) - moving window freeze and I am unable to kill explorer (via taskmgr, or cmdline TASKKILL). In command line I've got something like this (taskmgr shows that explorer.exe is still running - I've got the same PID every time I try to kill it and no diagnostic message): C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. C:\Windows\system32TASKKILL /F /IM explorer.exe SUKCES: proces "explorer.exe" o identyfikatorze PID 6296 zostal zakonczony. If I try to run another explorer.exe process at this point, I got desktop icon and start bar back but I cannot open any explorer window After few minutes explorer.exe finally dies and I am able to rerun it without rebooting File that I moved have two copies - one local and one on the external drive (the original file wasn't delete after move); Both copies seems to contain the same data (same length and CRC info) If this happen during move of multiply files, only some files are moved and one of them have two copies (both locally and on the external drive) What can I do to fix those explorer hangs? Added: The same problem exist when copying files, it hangsup between large files Similar problem exist when I tried to use TotalCommander (x64): copying paused at 80% of one of files, TC didn't hung up (but clicking cancel in copying dialog box doesn't have any effect). During this pause I can't kill TotalCmd.exe just like Explorer.exe Added (2): This problem seems to disappear when I use 32 bit applications (like TotalCommander (x86) ), but I need to do more testing to be sure of this Added (3): There are several errors in event log, source: disk, id: 11, qualifiers: 49156, task: 0, level: 2, keywords: 0x80000000000000 (This may be important, and I forgot to mention this): Main disk is encrypted via Truecrypt (boot-in password)

  Read the article

• Reusing slot numbers in Linux software RAID arrays

  - by thkala

  When a hard disk drive in one of my Linux machines failed, I took the opportunity to migrate from RAID5 to a 6-disk software RAID6 array. At the time of the migration I did not have all 6 drives - more specifically the fourth and fifth (slots 3 and 4) drives were already in use in the originating array, so I created the RAID6 array with a couple of missing devices. I now need to add those drives in those empty slots. Using mdadm --add does result in a proper RAID6 configuration, with one glitch - the new drives are placed in new slots, which results in this /proc/mdstat snippet: ... md0 : active raid6 sde1[7] sdd1[6] sda1[0] sdf1[5] sdc1[2] sdb1[1] 25185536 blocks super 1.0 level 6, 64k chunk, algorithm 2 [6/6] [UUUUUU] ... mdadm -E verifies that the actual slot numbers in the device superblocks are correct, yet the numbers shown in /proc/mdstat are still weird. I would like to fix this glitch, both to satisfy my inner perfectionist and to avoid any potential sources of future confusion in a crisis. Is there a way to specify which slot a new device should occupy in a RAID array? UPDATE: I have verified that the slot number persists in the component device superblock. For the version 1.0 superblocks that I am using that would be the dev_number field as defined in include/linux/raid/md_p.h of the Linux kernel source. I am now considering direct modification of said field to change the slot number - I don't suppose there is some standard way to manipulate the RAID superblock?

  Read the article

• Connection between Asp.Net and Oracle 10g Express Edition

  - by l3gion

  Hello, I'm struggling to find a way to connect my Asp .Net + C# application with my Oracle 10g Express Edition. Here's my scenario, I'm at Mac OS and I have 2 Virtual machines, one for Win 7 (VS 2010 app) and another with a Parallels Virtual Appliance with Oracle 10g Express Edition 1.1. Which provider (Oledb, ODP.NET, etc..) should I use? How to make the connection to the server in C#? Right now I have this: <appSettings> <add key="conn" value="Data Source=10.211.55.11;Persist Security Info=True;User ID=l3gion;Password=l3gion;" /> </appSettings> And at the .cs file: SqlCommand cmd = new SqlCommand("insert_thing", new SqlConnection(ConfigurationManager.AppSettings["conn"])); cmd.CommandType = CommandType.StoredProcedure; *insert_thing is a stored procedure Using this I got this error: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) I've searched for some possible solutions. Tried some, including: firewall disabled, allow remote connection at oracle express edition using this cmd line ("EXEC DBMS_XDB.SETLISTENERLOCALACCESS(FALSE);").. The error persists. Can anyone guide me into the right direction? I'm a newbie with this type of things. Thank you for your patience. regards

  Read the article

• Fixing a corrupted Windows Server 2003 server

  - by Keith

  I have a Windows Server 2003 server that is being mainly used for some reporting done in SQL Server. Recently Windows has started complaining about being corrupted, we are getting an NTFS error 55: The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume1. The server is RAID 5 and I did have a disk die however the RAID never went degraded since I have a hotspare. I replaced the hot spare and I'm still having problems. When I run chkdsk I get tons of messages.. some are: Deleting corrupted attribute record (128, "") from file record segment 194746 Those go on for a while. Then it deletes some orphan files. Then it does Correcting error in index $I30 for file 132426 And that goes on for a while. Then I get tons of Recovering orphaned file RE1AB6~1.LOG into directory file 534959 I have seen a lot of errors relating to the SQL Server reporting services. What are my options at this point? I would prefer to fix the issue instead of building a new server but I don't know if I can at this point.

  Read the article

• Computer crashes if left unattended AND running uTorrent, what could be?

  - by DiegoDD

  I have a weird problem in which, if I leave my computer unattended, AND I leave uTorrent open, downloading/seeding, the computer simply crashes after about 20 / 30 minutes (don't know exactly since if I leave it, and come back later, it has already restarted or has a BSOD.) If I leave the computer alone for undefined time WITHOUT uTorrent, nothing happens, and if I am constantly using the computer while using uTorrent, no problem either (I could be using it all day with uT open and it doesn't crash). So what could it be that the combination of those cases makes the computer crash? I have already checked the power management so the computer never enters stand by mode, sleep, hibernate, etc. (the only thing I do is turn off the display). A first guess is that maybe one of my external hard drives DO sleep or enters in a "low power" mode or something if I don't use the PC. but since uT is running MAYBE tries to use that drive, and makes it crash. Could that be possible? How to know for sure if the external drive does that, and to prevent it from doing so. Any more ideas of what may be causing that? Specs: Windows 7 Pro, 64-bit, 2 GB RAM. Latest version of uTorrent (although it has been happening for a while now). UPDATE: i just found out that uTorrent has Disk cache options ( preferences - advanced - disk cache ). I have no idea if that may be causing problems with my external drive, hence causing the crash.

  Read the article

• Software raid 0 with six disks performance

  - by user134880

  I have some problems with disk performance. I have 6 x WD 500Gb RE4 disks. Each disk gives 135Mb/sec throughput. All measurements are made with hdparm with options "-tT" (I know that it is just synthetic test, but I need some start point to make measurements). I have controller with Sil3124 x 4 ports PCI Express 1x So... RAID0 on controller with 2 disks gives 200Mb/s - ok, pcie limit. RAID0 on motherboard with 2 disks gives 270Mb/s - niceeee :) RAID0 on contorller with 4 disks gives 200Mb/s - ok, pcie limit. RAID0 on controller with 4 disks + 1 disks on motherboard = 340Mb/s ... :( RAID0 on controller with 4 disks + 2 disks on motherboard = 300Mb/s .... why? Any ideas? Maybe need more cpu power? Now there is Pentium D Dual core 2.8Ghz, 4Gb RAM. It is dedicated box for storage.. no other activity.

  Read the article

• HP Laptop recognizes hard drive just long enough to install windows

  - by Joe

  I have an HP laptop, DV6500 (CTO). It refused to boot one day, so I ran some diagnostics (a friend lent me "Hirens Boot Disk", "UBCD" and "PC DR 6"). Everything passed, except for the hdd. I replaced the HDD with a used drive of unknown condition. Installed windows with no problems. Installed the wireless driver, tried to reboot ... no luck. So I went to Best Buy, bought a brand new Western Digital 320gb HDD. Put it in the machine, installed windows (vista home premium). Installed the wired networking driver. Tried to reboot. No luck. Put the first hdd back in the machine, reinstalled windows. Started to install some drivers, went to reboot, and the machine won't come back to life. Put the second hdd in the machine, rinse wash and repeat. I've replaced the memory, even though it passed diagnostics. Problem exists with both brand new memory, and old memory. The BIOS recognizes the hard drive. The computer freezes directly after the bios splash screen, and there is no hard drive activity light. I've tried two linux live distros (gentoo and ubuntu). Neither would run on this laptop, but will on a different HP laptop. UBCD and Hirens Boot Disk both ran, as did PC Doctor 6 which refuses to test anything (gets stuck at "enumerating hard disks"). Is there anything else I can try?

  Read the article

• Help with Ubuntu and Windows, separate HDs

  - by LuxuryMode

  Need some major help. Running a Dell XPS/Dimension 630i. It came with "SATA 2 RAID 0 With Dual 500GB Hard Drives." I have installed a new, third non-raided drive and installed Ubuntu on it. So now I have Windows on the original hard drive and Ubuntu Linux on the new HD. When I get to the boot menu where I can select an OS, if I select windows I get an error: "No such drive, no such disk." Also, strangely in the first place, in order to even get to the bootloader menu I have had to disable ALL ports under the RAID config. Unless I do this, I will just get to a never-ending blinking cursor. I have tried every conceivable CMOS config and nothing else works. Tried setting port 3 (the new HD w/ Ubuntu) to first hard disk boot priority. Tried disabling all other ports and enabling the Ubuntu HD port and vice versa. I have some pictures of boot up: first one is strange error i get after messing with CMOS to finally get ubuntu install to work. http://imgur.com/5sqJa then boot menu: http://imgur.com/TWtLq then error: http://imgur.com/TJ1mS. Also, please note that I can actually access all files from the raided Windows drive through Ubuntu.

  Read the article

• Data recovery from corrupt Ubuntu partition/directory (question about a previous answer)

  - by JoshMaurice

  I have an Ubuntu installation that won't boot anymore. I asked my previous question about it here: http://superuser.com/questions/15916/ubuntu-chkdsk-equivalent Bolotov replied: As I see from your previous question you can boot Windows so you could use dskprobe from Windows XP Service Pack 2 Support Tools to make sure that fs type is correct ... but it's already correct fs type 7 is NTFS. Message "The type of the filesystem is RAW. CHKDSK is not available for RAW drives." means that windows can't determine fs type for some reason. As we see fs type is correct. To run Chkdsk on your Windows partition you can install Windows Recovery Console, boot in recovery console and check your disk. After checking the disk you will gain access to you c:\ubuntu\disks. I think you can mount your linux partition (which is in file) as usual loop-back device: mount -o loop [path to your linux-loopback-partition] But you should mount windows patrition first. So now I'd like to know: Within the recovery console I will be issuing the commands "chkdsk -r" and then "mount -o loop [path to windows partition]" and then "mount -o loop c:\ubuntu\disks", correct? I do have a ("corrupt and unreadable") c:\ubuntu\disks directory so that appears to be the correct path to the linux partition; do you know the path to the windows partition? would that be just "c:\"?

  Read the article

• Some Apps don't start on Windows 8 Release Preview

  - by Exa

  I recently installed the Release Preview of Windows 8 in a virtual machine. Some apps do not work. When I open them (by clicking on their tile in the start screen) I see a splash screen and nothing else happens. Sometimes the app crashes after 30 seconds, sometimes it just keeps on loading. A good example is the "Map"-App from Windows 8 or the app "Cookbook" by Bewise. I installed Cookbook and when I had a look at the task manager I saw that it was the 32bit version running, but I have an x64 Windows 8... Could this be a problem? Shouldn't the Windows Store download the correct version? This is the setup of my virtual machine: Windows 8 Release Preview x64 Oracle VirtualBox 4 of 8 cores from host system 8 of 16 GB RAM from the host system 256 MB graphics memory guest additions installed resolution 1920 x 1080 Do you need further information? Unfortunately there is no error message... I just see the start screen of the app with its logo and it keeps loading, but nothing happens. Other Apps (like Mail, Video, Social, etc.) work fine.

  Read the article

• Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

  - by camelCase

  I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

  Read the article

• IIS6 site using integrated authentication (NTLM) fails when accessed with Win7 / IE8

  - by Ciove

  Hi, I'm having pretty similar problems as described in case 139099, but the fix there doesn't seem to work for me. Here's the details: Server: Win2003Srv R2 SP2 (stadalone, not a member of a domain). IIS6, TCP/443 (https). Anonymous access disabled. Integrated Windows authentication enabled. Local useraccouts Each useraccount has own virtual folder with change access and read access to site root. The 'adsutil NTAuthenticationProviders "NTLM"' -thing set to site root and useraccount's virtual folder. Client: Win7 Enterprise Member of a AD-Domain IE8 Allows three login attepts then fails. Using [webservername][username] in the logon window (Windows security) Logon using other browsers (Chrome and Firefox) works OK. The Web services log shows one 401.2 and two 401.1 events. The Security Event log shows two events, first is Fauilure Audit (680), The second event is Fauilure Audit (529) with these details: Logon Failure: Reason: Unknown user name or bad password User Name: [username] Domain: [webservername] Logon Type: 3 Logon Process: NtLmSsp Authentication Package: NTLM Workstation Name: [MyWorkstation] Caller User Name: - Caller Domain: - Caller Logon ID: - Caller Process ID: - Transited Services: - Source Network Address: [999.999.999.999] Source Port: 20089 Any ideas appreciated.

  Read the article

• Linux Software RAID1: How to boot after (physically) removing /dev/sda? (LVM, mdadm, Grub2)

  - by flight

  A server set up with Debian 6.0/squeeze. During the squeeze installation, I configured the two 500GB SATA disks (/dev/sda and /dev/sdb) as a RAID1 (managed with mdadm). The RAID keeps a 500 GB LVM volume group (vg0). In the volume group, there's a single logical volume (lv0). vg0-lv0 is formatted with extfs3 and mounted as root partition (no dedicated /boot partition). The system boots using GRUB2. In normal use, the systems boots fine. Also, when I tried and removed the second SATA drive (/dev/sdb) after a shutdown, the system came up without problem, and after reconnecting the drive, I was able to --re-add /dev/sdb1 to the RAID array. But: After removing the first SATA drive (/dev/sda), the system won't boot any more! A GRUB welcome message shows up for a second, then the system reboots. I tried to install GRUB2 manually on /dev/sdb ("grub-install /dev/sdb"), but that doesn't help. Appearently squeeze fails to set up GRUB2 to launch from the second disk when the first disk is removed, which seems to be quite an essential feature when running this kind of Software RAID1, isn't it? At the moment, I'm lost whether this is a problem with GRUB2, with LVM or with the RAID setup. Any hints?

  Read the article

• Is there a clean way to obtain exclusive access to a physical partition under Windows?

  - by zneak

  Hey guys, I'm trying, under Windows 7, to run a virtual machine with VMWare Player from an OS installed on a physical partition. However, when I boot the virtual machine, VMWare Player says that it couldn't access the physical drive for writing. This seems to be a generally acknowledged problem in the VMWare community, as Windows Vista introduced a compelling new security feature that makes it impossible to write to a raw drive without obtaining exclusive access to it first. I have googled the issue and found a few workarounds. However, the clean ones seem to only work on whole physical disks, and not on partitions. So I would be left with the dirty solution. In short, it meddles with the MBR to erase any trace of the partitions to use, makes Windows forget about them, then restores the MBR so we can launch the VM. I'm not sure I want to do that. Is there a way to let VMWare acquire exclusive access to the partition without requiring me to nuke it away? What I'd be looking for, I suppose, is a way to put just partitions offline instead of whole physical drives.

  Read the article

• Apache, logerror and logrotate: what is the best method?

  - by OlivierDofus

  Hi! Here's a vhost example of my sites: <VirtualHost *:80> DocumentRoot /datas/web/woog ServerName woog.com ServerAlias www.woog.com ErrorLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/error_log 86400" CustomLog "|/httpd-2.2.8/bin/rotatelogs /logs/woog/access_log 86400" combined DirectoryIndex index.php index.htm <Location /> Allow from All </Location> <Directory /*> Options FollowSymLinks AllowOverride Limit AuthConfig </Directory> </VirtualHost> I've got 12 sites running now. This gives something like: [Shake]:/sources/software/mod_log_rotate# ps x | grep rotate /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/error_log 86400 [snap (as many error_log as virtual hosts)] /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 /httpd-2.2.8/bin/rotatelogs /logs/[hidden siteweb]/access_log 86400 [snap (as many access_log as virtual hosts)] grep rotate [Shake]:/sources/software/mod_log_rotate# !!! I've been looking everywhere but I've only found mod_log_rotate. The "little" problem is that the author (very good C developper) explains: "Unfortunately Apache error logs are handled in such a way that we can't work the same log rotation magic on them. Like transfer logs they support piped logging though so you can still use rotatelogs for them. " So my question is: what would be the best way to handle multiple logs? If I just do a very classical log and I use the system's "logrotate" program couldn't this be a good deal? How would/do you deal with that? Thank you!

  Read the article

• I need a driver for my Cardbus USB 2.0 card

  - by Carl

  The picture and details of the card are here: http://www.ht-link.com/en/ProductView.asp?ID=106 The Windows drivers for this don't work right. I tried them on my previous laptop, and then installed the ones off their included CD. (Note that the systems requirements includes a CD-ROM drive...) I have a new laptop, and lost the CD. The website that lists the drivers is broken - the download links don't work. It is here: http://www.ht-link.com/en/DownView.asp?ID=10 I need the very first link - The Win XP drivers for the HT-112NEC. The company does not reply to my e-mails. I've tried searching Google for other sources for the driver (I didn't bother with those sites that want me to install driver detection software or create a log-in for their site). [Here's the problem I am getting using the drivers Windows XP SP3 installs: When I plug in my USB 2.0 hard-disk adapter, a USB Mass Storage Device entry is added in the Device Manager, but there is no entry under Disk Drives, and a drive letter is not assigned, so I can't access the driver. Like I said, this card didn't work without their special drivers on my other laptop, either.]

  Read the article

• Recommended Win2k8 Server software to fix my RAID-0 issue

  - by Jason Kealey

  I'm running an Asus P6T V2 Deluxe. It has six SATA ports and supports onboard RAID. I am using two of those ports for a RAID0 array of 1.5TB Seagate drives using the onboard RAID controller. One of them is giving me SMART warnings and I want to preemptively replace it. I pulled out two other 1.5TB drives from another computer and am ready to use one or both, if necessary. I can't run any SMART diagnostic software from within Windows because it only sees the hardware RAID-0 array, not each individual drive. The first thing I tried was a slow sector-by-sector copy using a free tool called EASEUS Disk Copy. Used the bootdisk, copied (took like 16 hours), unplugged the defective drive and plugged the new one in its place. The motherboard didn't recognize the new drive as being part of the known setup, so it did not want to boot. The second thing I tried was using other software (I forget the name) to copy the partition from within Windows. The first software failed because I had a server operating system. I found another software (I forget the name) which supported a server OS and did a partition copy onto the new drive. This seemed to work and the OS started to boot, but blue screened and started a reboot cycle. I'm assuming the software I was using was no good as it was trying to copy the boot disk while it was in use. I am looking for recommendations on what software to use to fix my problem without doing a re-install. Everything is backed up but my computer works fine and I'd like to avoid re-installation when possible. However, my system would be back up now if I had just started over on a second RAID array. :)

  Read the article

• What games work well on MacBook Pro (i7/GeForce GT 330M) within VMWare Fusion?

  - by webworm

  I have a 15" MacBook Pro (2.66 i7 with 8 GB RAM) with the GeForce GT 330M 512 MB graphics card. I use it primarily for development (Mac/Web/Windows) though I would like to play the occasional game with my son who uses a desktop PC system at home. I prefer to use VMWare Fusion for virtualization rather than BootCamp for a number of reasons. Heat/Fan issues with i7 under BootCamp Prefer to retain virtual machine as single file rather than dedicated partition (easier to move a nd backup) I have heard that Windows support of the GeForce GT 330 in BootCamp is not all that good. So that being said I was wondering what sort of games I would be able to play within the Fusion environment running Windows 7. I have 8 GB RAM and usually dedicate 4 GB to the virtual machine. I don't expect to be able to play the latest FPS games such as BattleField: Bad Company 2 or Call of Duty, rather I am looking at games such a Total War II, Civilizations IV, Supreme Commander, and other RTS type games. I should mention the native screen resolution of my MacBook Pro is 1680x1050, which is what I would be most likely running the VM at (fullscreen). Thank you for any advice.

  Read the article

• which virtualization technology is right for me?

  - by Chris

  I need a little help with this getting this sorted out. I want to setup a linux virtual server that I can use to run both sever and desktop systems. I want a linux system that is minimalist in nature as all the main os will be doing is acting as a hypervisor. The system I'm trying to setup will be running a file server, windows 7, ubuntu 10.04, windows xp and a firewall/gateway security system. All the client OS'es accessing and storing files on the file server. Also all network traffic will be routed through the gateway guest os. The file sever will need direct disk access while the other guests can run one disk images. All of this will be running on the same computer so I wont be romoting in to access the guests OS'es. Also if possible I would like to be able to use my triple head setup in the guest OS'es. I've looked at Xen, kvm and virtualbox but I don't know which is the best for me. I'm really debating between kvm and virtual box as kvm seem to support direct hardware access.

  Read the article

• P2V Wouldn't Boot, Rebuilt initrd, Need to Clean Up

  - by Mike Soule

  We have a CentOS 5.4 server (build 2.6.18-164.el5xen). We went to P2V this server so we can have redundancy, the physical only has one PSU. The P2V only completed 99% of the way, we have a VMWare ticket opened, but they marked the ticket as low priority. I was able to boot into a rescue disc of Red Hat 5.4 and rebuild the initrd with the help of this blog post. Now the only issue is the original server had a modified initrd, which was also from a different OS build and made by an outside provider. We do not have a document outlining modifications. My question is, is it at all possible to copy the initrd off of the physical server and replace it on the virtual and some how have the virtual machine boot? Thanks for any input. Edit: I copied the initrd img from the physical and it recreated the original issue. Here is a screen capture of the error. http://i.imgur.com/MqC73.jpg Edit2: echo Scanning logical volumes lvm vgscan --ignorelockingfailure echo Activating logical volumes lvm vgchange -ay --ignorelockingfailure VolGroup00 resume /dev/VolGroup00/LogVol01 echo Creating root device. mkrootdev -t ext3 -o defaults,ro /dev/VolGroup00/LogVol00 echo Mounting root filesystem. mount /sysroot

  Read the article

• Handling emails on a web server - Making sure the FQDN is set correctly based on the website sending the email

  - by webnoob

  I have a Windows 2008 Web Edition server hosting multiple websites using IIS 7.5. At the moment, all the emails are sent via the IIS6 SMTP service. The FQDN of the SMTP service is set to the computer name at the moment which isn't correct as it doesn't resolve to a valid DNS entry and is not RFC compliant. Some questions: Is there any way I can change the FQDN of the SMTP service based on the site sending the email? Would it be Ok to just setup mailserver.mydomain.com and use that as the FQDN for all the sites on multiple domains. Should I be using some other mail server software to handle this better? The reason I am asking is lots of emails are hitting spam folders because the settings are incorrect. I have access to the code that is running the websites so if something needs to be done there then that shouldn't be a problem. The sites are written using ASP.NET 2.0. EDIT: I have just found an option to create an SMTP virtual service. Would this be the way forward? Create a virtual server for each site? Thanks.

  Read the article

< Previous Page | 335 336 337 338 339 340 341 342 343 344 345 346  | Next Page >