Search Results

Search found 15651 results on 627 pages for 'setup'.

Page 340/627 | < Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >

• Is there a way to submit a batch of commands to a Cisco router and have them execute from the router?

  - by atroon

  I need to change the configuration of a remote (6 hours' drive) client's Cisco 871 (IOS 12.4.15T) from my location because of some new internet service at his location. To be more precise, I need to change the default route, ip address of the outside interface (Fa4) and disable the PPPoE setup there. Unfortunately, doing any of this will (obviously) break the connection to the router. I do not have an out-of-band management modem set up (I know, I know). Is there any way to enter the commands I need to have run and have them execute one after the other, from a file on flash:? I have never tried anything like that before. Essentially a DOS-style batch file is exactly what I need. Nothing like it seems to be out there except using kron to execute CLI commands, but that is specified here as only taking EXEC commands, not configuration ones. Is there hope, or do I travel?

  Read the article

• Can make the proxy settings invisible when I share my internet connection via wifi?

  - by Neil

  This is probably a long shot... I have an HTC Desire and frustratingly found out after I got it that it doesn't support network proxy settings. We have a wireless network at my office that uses a proxy. My desktop at work runs ubuntu. I was wondering if the following set up would work: Plug a USB Wireless adapter into the desktop that has a working internet connection using the proxy. Setup the wireless adapter as an ad-hoc network Share the internet connection over the ad-hoc network. Make it so that the use of the proxy is invisible to users of the shared network connection. Connect the Android phone to the ad-hoc wireless network and utilise the internet connection. My question is this: Is this possible or should I give up now and not even try? I think I can handle steps 1, 2, 3 and 5. I just have no idea if step 4 even makes sense, let alone is possible. Thanks

  Read the article

• Plesk 9 - Client panel access via client domain, not server host name

  - by Ben

  I've setup a Plesk 9 vps recently. The plesk admin is accessible at, say, http://superawesomedomain.com:8443. I'm setting up a couple of client domains on the server. I'd like clients to be able to access plesk via a similar url, but instead it would be something like http://inferiorclientdomain.com:8443. This works ok in a sense, but it always redirect the request for inferiorclientdomain.com:8443 to superawesomedomain.com:8443. I'd like the control panel access url to remain on inferiorclientdomain.com. Is that possible? EDIT: System Info. Plesk 9.5.2 on CentOS 5 (Build 95100504.12)

  Read the article

• Windows 7 Default Gateway problem

  - by Matt

  I have a strange problem (or at least seems strange to me) the below are IP configurations for two laptops on my home network which consists of a main router 192.168.11.1 and a connected wireless router (i know this can cause problems but has always worked until I got the win7 machine) at 192.168.11.2 with DHCP disabled. Laptop 1 - Win XP IP: Dynamically assigned by main router default gateway: 192.168.11.1 (main router) This machine gets perfect connectivity. Laptop 2 - Win7 IP: dynamically assigned by main router Default Gateway: 192.168.11.2 THIS IS THE PROBLEM... I cannot seem to get this machine to default to the main router for the gateway UNLESS I go to a static configuration which I would rather not do since I regularly go between my home and public networks. Why is my Win7 machine not finding the main gateway the same way that the other laptop is? I believe that the rest of my setup is fine as it has always worked and it works perfectly when set as static ip and gateway. Please help! Thanks

  Read the article

• What emulator / VM software can I use to create a Win32-portable Linux Guest?

  - by Jotham

  Hi, I want to create a portable VM setup so that I can boot a Linux install regardless of which Windows XP / Windows 7 host machine I am on. I was looking at Qemu but it doesn't appear to have a relatively safe win32 build. Other things like VirtualBox require complete install on the host OS for performance reasons. I'm not so concerned about performance, I just want to run a few curses based applications. My ideal end goal would be a a memory stick of some size with a VM/Emulator I can boot on most WinXP/Windows 7 machines and access my own curses based applications (probably archlinux or debian). Any help would be appreciated. Regards,

  Read the article

• Joomla Secondary Users

  - by Gaz_Edge

  Background I have a joomla based application. My customers sign up and they register as a user on the site. My customers (primary customers) then have their own space on the site that they can then setup their own customers (secondary customer). Question/Problem The problem I am having is that I need to tag each secondary customer to a primary customer. I thought about just creating a new component and having a separate table that includes all the secondary customers. The problem is that I then lose out on all the authentication, session handling and login/logout that the core joomla _users component offers. I then thought about just having all the users in the core _users table and add the primary customer associated with each secondary customer to a field in a profile plugin. This would work for the most part, but this means that primary customers cannot create a secondary customer with a user name that already exists in the _users table. I didn't think this would be an issue, but several of my primary customers (currently only test users) have been confused by the site telling them a username is not available, since they can only see the names of their own secondary customers. Any ideas on some architectural changes I could make to solve this?

  Read the article

• Configuring Linux Network

  - by Reiler

  Hi I'm working on some software, that runs on a Centos 5.xx installation. I'ts not allowed for our customers to log in to Linux, everything is done from Windows applications, developed by us. So we have build a frontend for the user to configure network setup: Static/DHCP, ip-address, gateway, DNS, Hostname. Right now I let the user enter the information in the Windows app, and then write it on the Linux server like this: Write to /etc/resolv.conf: Nameserver Write to /etc/sysconfig/network: Gateway and Hostname Write to /etc/sysconfig/network-scripts/ifcfg-eth0: Ipaddress, Netmask, Bootproto(DHCP or Static) I also (after some time) found out that I was unable to send mail, unless I wrote in /etc/hosts: 127.0.0.1 Hostname All this seems to work, but is there a better/easier way to do this? Also, I read the network configuration nearly the same way, but if I use DHCP, I miss som information, for instance the Ip-address. I know that I can get some information from the commandline (ifconfig), but I dont get for instance Hostname, Gateway and DNS. Is there a commandline tool that will display this?

  Read the article

• Configure Postfix to use external MX servers for delivery of local mail if user is unknown

  - by mr.b

  I have a following setup: linux box with postfix configured to be responsible for example.com domain domain's MX servers are configured so that mail sent to example.com is sent to google mail servers several user accounts on linux machine exist (same machine also hosts example.com site) When someone from the outside attempts to send mail to address ending with @example.com, it gets routed to google mail (and there handled appropriately). When linux machine tries to send mail to outside world, mail is delivered correctly, as reverse dns and spf records are configured correctly, so linux machine is valid mail sender for example.com domain (along with google mail servers). However, here's the problem. When php application (hosted at linux box) tries to send mail to [email protected] (and someuser doesn't exist on linux box), it fails, since it doesn't even consult google mail servers, but postfix smtp locally concludes that "someuser" is unknown. So, the question is: how do I tell postfix to relay mails sent to @example.com domain to google mail servers (so, to servers specified in MX records), IF and only if a mailbox is not found locally.

  Read the article

• Wireless card not found on Ubuntu

  - by idealflip

  Hello all, I'm trying to setup Ubuntu on an old PC. I ran the following command, lspci, in order to get info on the wireless card installed. 00:0a.0 Ethernet controller: Marvell Technology Group Ltd. 88w8335 [Libertas] 802.11b/g Wireless (rev 03) Does anyone know where I can get drivers for this card/chip? And also, how to install (I'm rather new to linux). Also, I'm sure the card is working because I just formatted over xp, and everything was working well. Thanks in advanced!

  Read the article

• stunnel: SSL-to-SSL? (for smtp/imap)

  - by nonot1

  Hello, How can I configure stunnel to accpet SSL connections, and connect then to an SSL port on a different server? Here is my setup: Our ISP's server, "Mail Server", supports smtp/imap over SSL. (Not starttls. Just over ssl.) But, I have a bunch of client machines that will only trust a specific, internal, root certificate. Thus, they can not connect to "Mail Server". For these client machines, I'd like to make a dedicated "Mail Tunnel" host that uses stunnel to listen with an in-house signed SSL certificate, and just forward data to "Mail Server" using a 2nd SSL connection. Can this be done? What would be the specific steps for Ubuntu Server 10.10? (I'm not too familiar with persistent service configuration.) Thank you

  Read the article

• "Always available offline" option missing on one network drive in Windows 7

  - by Rynardt

  My network setup at home has 2 network storage devices on the network. The one is for media content on a Popcorn Hour A-110 and the other is a D-Link DNS-320 in RAID 1 configuration for business files. When I access these network drives and right click a folder the following context menu appears for the A-110 device, but not for the D-link. I have tested this in both Windows 7 32bit and Windows Vista 64bit. In both instances the "Always available offline" option is only available for the A-110 storage device, and not for the D-link. How do I get this option for the D-link? Any advice or ideas are welcome.

  Read the article

• How to install Ubuntu 12.04.1 in EFI mode with Encrypted LVM?

  - by g0lem

  I'm trying to properly install Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with the alternate install CD ".iso" on a lenovo Thinkpad X220. Default Hard Disk (with a pre-installed version of Windows 7) has been replaced with a brand new SSD. The UEFI BIOS of the lenovo Thinkpad X220 is set to "UEFI Boot only" & "USB UEFI BIOS Support" is enabled (I'm using an external USB DVD reader to perform Ubuntu installation). The BIOS is a Phoenix SecureCore Tiano, BIOS version is 8DET56WW (1.26). The attempts below are made with the UEFI BIOS settings described above. Here's what I've tried so far: Boot on a live GParted CD Create a GPT partition table Create a FAT32 partition for UEFI System, set the partition to "EF00" type ("boot" flag) Leave remaining space unformated Boot on Ubuntu 12.04.1 LTS 64-bit PC (AMD64) with alternate CD: Perform the install with network updates enabled Use manual partitioning FAT32 partition created with GParted is used as "EFI System partition" Remaining space is set to be used as "Physical volume for LVM" Then "Configure encrypted volumes" using the previous "Physical volume for LVM" as the encrypted container, passphrase is setup. "Configure the Logical Volume Manager" creating a volume Group using the encrypted container /dev/mapper/sda2_crypt Creation of the Logical Volumes "Create logical volume", choosing the previously created volume Group Assign a mount point and file system to the Logical volumes : LV-root for / LV-var for /var LV-usr for /usr LV-usr-local for /usr/local LV-swap for swap LV-home for /home NOTE: /tmp would be in RAM only using TMPFS Bootloader step: neither my ESP partition (/dev/sda1, /dev/sda or MBR) seems to be the right place for GRUB, I get the following message (X suffix is for demonstration only): unable to install grub in /dev/sdaX Executing 'grub-install /dev/sdaX' failed This is a fatal error. Finish installation without the Bootloader & Reboot The system doesn't start, there's no EFI/GRUB menu at startup. What are the steps to perform a clean and working installation of Ubuntu 12.04.1 Precise Pangolin, 64bit version in U(EFI) mode using the encrypted LUKS + LVM scheme described above?

  Read the article

• Installing Office 2010 through group policy without an msi

  - by Ri Caragol

  I have been breaking my head for several days now trying to install Microsoft office 2010 through group policy. Unfortunately Microsoft decided it would be fun to release office without an MSI and so I either Need to create an msi for it or Need to install it through a logon script that would run the setup.exe from a network location. Any advise would be greatlly appreciated. I tried to create a script but even though I double click it and it runs properly, it does not seem to kick in when users log in or when the machine is turned on. Also is there an easy way to create an msi?

  Read the article

• Installing linux mint in one partition

  - by sha404

  So, I have a disk with a MBR setup(image below). I've managed to have 50 GB unallocated space for intalling Linux Mint 14. And I want to keep the current windows OS too(but don't want the Mint inside windows). Now I've seen in some tutorials that Linux Mint needs several partitions for bootloader, swap, & home. I don't like to have so many partitions & maybe MBR stuff won't let me create more than one now. So, is it possible to install Linux Mint in one partition only? If it is really impossible than what's the minimum number? & how can I accomplish that? Thanks in advance.

  Read the article

• CentOS 6 - YUM Local Repo - Ensure consistent package distribution

  - by Mike Purcell

  I've read a few guides outlining how to setup a local YUM repo, but none of them explicitly stated an answer to my question; If I set up a local YUM repo, does that mean that any CentOS servers which pull from said repo will never be "ahead" of the local YUM repo? I want to ensure a consistent package distribution across all my servers. Right now, when I do a yum update, even on a daily basis, the servers can be out of alignment. For example if I run YUM update on my dev server in the morning, then run YUM update on one of my production servers in the afternoon, the production server may have picked up a new version of a package that the dev server did not pick up, due to the time window between the update commands. Rather, I'd prefer that I run yum update from my dev server which has access to remote upstream yum repos, then let it sit for 2 weeks, after which I run yum update on my production servers against the local repo on my dev server.

  Read the article

• SMTP IP - Bad reputation, how do I work around?

  - by Louis van Tonder

  I recently had a spamming incident and got listed on a blacklist. I have rectified the issue, removed from the blacklist, but my IP reputation is now classified as a high volume sender. What is the best way to rectify this? I have an additional IP address. I am thinking configure my server to make outbound SMTP connections using the other IP. My questions are: How long does it take for my reputation to stabilize again? How do I configure my server/mailserver to use a specified outbound IP? Setup: Server 2008 Web hMailserver 2 IPs configured on one NIC Cloud based server Your urgent help would be greatly appreciated. Cheers

  Read the article

• Using VirtualBox/VMWare to deploy software to multi sites ?

  - by Sim

  Hi all, I'm currently evaluating the feasibility of using VirtualBox (or VMWare) to deploy the follow project to 10 sites Windows XP MSSQL 2005 Express Edition with Advanced Services JBoss to run 1 in-house software that mostly query master data (customers/products) and feed to other software Why I want to do this ? Because the IT staffs in my 10 sites are not capable enough and the steps taken to setup those "in-house project" are also complicated What are the cons I can forsee ? Need extra power to run that virtualbox instance The IT staffs won't be much knowledgeable 'bout how to install the stuffs Cost (license for VirtualBox in commercial environment as well as extra OS license) I really seek your inputs on the pro/con of this approach, or any links that I can read further Thanks a lot

  Read the article

• Play system sounds from one computer through another computer's speakers?

  - by kevinconner

  I have a Mac and a Windows PC at work. I use both at the same time with Synergy and SynergyKM, which is a great setup for me. The Mac has built-in speakers and the PC has a sound card, but no speakers. I don't want to get speakers for use at work; instead I'd rather just have all sounds from both computers play through the Mac's speakers. Is there some sort of audio service I can run on each computer to accomplish that? I would want: System alert sounds, like you configure in the Control Panel Sounds from videos in a web browser, including from Flash

  Read the article

• Srvany Starts but Application doesn't

  - by mharran

  I used Instsrv and Srvany as to create a service on W2008; the Srvany service starts okay but the application does not start. The application is TeamSpeak 3 btw. I don't think it's an issue with my W2008 setup as I have a previous version of the application set up the exact same way and running perfectly. Also, I have no problem manually starting the application even when I copy and paste into the 'Run' box the path used for the application by Srvany. I looked at Events but nothing there except notification that the service has entered the running state, didn't really expect any errors as the service has started even though the application hasn't. Any suggestions on what could be the problem?

  Read the article

• Port numbers in Visual Studio projects and IIS

  - by aspdotnetuser

  I have a few questions about localhost and port numbers as this is an area where I do not have a lot of knowledge, and because I recently had to work with setting up Visual Studio projects and IIS and there are things I'm not clear on. I have the following questions on the things I find confusing. I thought it made more sense to include them all in one question instead of making separate questions. I have noticed a random port number is generated with projects I have worked on in the past, but I recently saw a project where the port number was fixed. What is the purpose of having a fixed/default localhost port number? i.e is it particularly useful on projects that have many programmers working on the project? If a solution contains multiple projects (for example, WCF services, Domain, MVC/Web pages), is it possible to setup a different localhost port for each of them? If so, what is the benefit of this? If a solution contains multiple projects and has different localhost urls/port numbers, must there be a corresponding website (and application pool) for each project in IIS? Or just for the project that contains the actual web pages?

  Read the article

• Removing partition to install OS?

  - by Shane

  So i have a computer that has 2 hard drives and i installed Ubuntu server on it. I used LVM to connect the two. So i tried to put windows back on it but it failed because it said it couldn't position the drive and then when i booted again the OS couldn't be found. So i booted it with the Ubuntu setup disc but now when it goes to partition it says that the position can not be modified because its already in use. I am asking if there is a way i can just remove everything and start fresh?

  Read the article

• Unable to install Android for Windows 7 because JDK is not found

  - by user1294663

  I have JDK SE7u4 installed in windows 7. I tried to install Android on Windows 7 using the installer_r18-windows.exe but no avail. The setup window showed the message saying that the Java SE JDK not found and ERROR: Failed to find Java version for C:\Windows\System32\java.exe The system cannot found the file specified. If you believe you have a JDK installed and it was not properly recognized, simply set an environment variable JAVA_HOME to point to it I right clicked on Computer Properties Advanced System Settings Environment variables. I created a NEW system variable called JAVA_HOME and set the value as C:\Program Files\Java\jdk1.7.0_04\bin or C:\Windows\System32\java.exe. I ran the installer again — the same error message still appeared.

  Read the article

• Google Apps for Business on a separate infrastructure?

  - by dustin

  Does anyone know if Google Apps for Business edition hosts the apps (gmail, calendar, etc.) on a physically separate infrastructure than the Standard (free) infrastructure? We've been growing increasingly annoyed with the lost/severely delayed email messages, downtime, etc. of Google Apps (standard) over time, and we are wondering if moving to the paid version would bring any benefits. Specifically, if the Business edition is not in some way on a different physical infrastructure, and we are in essence paying for a few small perks but still run on the usual standard/free setup, then we would probably have the same (or just as many) issues with the Business version. I've emailed Google's sales team responsible for GApps, but haven't heard anything back in 4 days, which already doesn't speak well for the service. So, anyone have any insight into this? Thanks in advance for any and all help :)

  Read the article

• Setting up Tornado with Nginx on Ubuntu 10.04 for production use

  - by DjangoRocks

  Hi all, I understand that there's an nginx configuration file at http://www.friendfeed.com But i don't really know how to set up Tornada for production use on Ubuntu 10.04 with Nginx. Here's my situation and assumptions: 1) Assuming my Tornado project is set up as such: project/ src/ static/ templates/ project.py And I have installed Tornado by downloading the repositary from Github and than sudo python setup.py install 2) I've installed Nginx and started it based on the instructions here : http://library.linode.com/web-servers/nginx/installation/ubuntu-10.04-lucid My questions are: Where does my nginx configuration file go ? Within the src/ folder? After configuring Nginx, how do I start my Tornado project?

  Read the article

• WDS - Clients receive Error: PXE-E53: No boot filename received

  - by Ninja2k

  I have setup WDS on Windows 2008 server in a Vmware box so I can practise setting up WDS,the server has DNS and DHCP as well as AD, the boot image is confirmed as working but when my clients try to boot up it does not work. I have checked the following: Clients can ping the WDS server. The WDS service is started Boot images for X86 and X64 are deployed. HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\WDSServer\Providers\WDSPXE UseDhcpPorts has been set to 0 My clients just receive Error: PXE-E53: No boot filename received. Any idea what could be wrong?

  Read the article

< Previous Page | 336 337 338 339 340 341 342 343 344 345 346 347  | Next Page >