Search Results

Search found 10963 results on 439 pages for 'documentation generation'.

Page 345/439 | < Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >

• compile ntp without ssl

  - by Zulakis

  I need to deploy ntp to a very space-critical pxe-imaging-system. (Yes, each KB matters.) Footprint needs to be as small as possible, so I want to compile ntp without linking openssl. According to the manual this is should be possible: If available, the OpenSSL library from http://www.openssl.org is used to support public key cryptography. The library must be built and installed prior to building NTP. The procedures for doing that are included in the OpenSSL documentation. The library is found during the normal NTP configure phase and the interface routines compiled automatically. Only the libcrypto.a library file and openssl header files are needed. If the library is not available or disabled, this step is not required. I already tried out ./configure --without-openssl however, this didn't help. This is my ldd output: ldd ntpd/ntpd linux-gate.so.1 => (0xb7706000) libm.so.6 => /lib/i686/cmov/libm.so.6 (0xb76d5000) libcrypto.so.0.9.8 => /usr/lib/i686/cmov/libcrypto.so.0.9.8 (0xb7582000) librt.so.1 => /lib/i686/cmov/librt.so.1 (0xb7578000) libc.so.6 => /lib/i686/cmov/libc.so.6 (0xb741d000) /lib/ld-linux.so.2 (0xb7707000) libdl.so.2 => /lib/i686/cmov/libdl.so.2 (0xb7419000) libz.so.1 => /usr/lib/libz.so.1 (0xb7404000) libpthread.so.0 => /lib/i686/cmov/libpthread.so.0 (0xb73eb000) The system I am compiling on is 32-bit debian lenny using openssl 0.9.8g-15+lenny16. What is the correct configure option to compile ntp without openssl?

  Read the article

• Running HTTP and HTTPS connections for a single domain (say, www.example.com) through a Cisco ACE SS

  - by Paddu

  My web application config has a Cisco ACE load balancing across a server farm and I want to use the ACE as an SSL endpoint as well. To make this work, the network architect has come up with a design where all secure pages have to be served from secure.my-domain.com, while non-secure pages are served up from www.my-domain.com. The reason for this is apparently that the configuring the Cisco ACE to accept HTTPS requests on port 443 for a particular public IP prevents the simultaneous acceptance of HTTP requests on port 80 for the same IP. While I'm not a networking (or Cisco) expert, this seems to be intuitively wrong, as it would prevent any website using the Cisco ACE to serve pages on http://www.my-domain.com and https://www.my-domain.com simultaneously. In this situation, my questions are: Is this truly a limitation of the Cisco ACE when used as an SSL endpoint? If not, then can I assume that we can set up the ACE to accept connections for a particular IP on ports 80 and 443, and function as an SSL endpoint for the incoming requests on 443? Links to appropriate documentation most welcome here. Assuming the setup in the previous question, can I then redirect both sets of requests to the same server farm on the same port?

  Read the article

• AviSynth ChangeFPS: combining videos with different framerates

  - by Daniel Saner

  I have two video recordings of the same scene, but with different framerates, that I would like to combine using an AviSynth script. One video is recorded at 30fps, the other at 120fps. What I would like to do is to keep them temporally synchronised, meaning that for each frame of the 30fps video, the output should display 4 frames from the 120fps video. I would like the final output video to play at 30fps so that the duration is 4 times the original recordings. From AviSynth's documentation, it seems ChangeFPS is the function I'll need, since it removes and duplicates frames, while 'AssumeFPS' just changes the playback speed (and my plan is basically to quadruple every frame of the 30fps clip). However, the filter does not seem to do what it says. If I try: clip30 = AviSource("0326.avi").ChangeFPS(120) clip120 = AviSource("0326-120fps.avi") it doesn't affect the playback speed or frame count of the 30fps clip at all, but removes every fourth frame from the 120fps clip, which is not at all what I want. Unfortunately, appending .ChangeFPS(7.5) to the clip120 instead does not have the same inverse effect—in that case, it does exactly what's to be expected. Alternatively, if I try: clip30 = AviSource("0326.avi").AssumeFPS(7.5) clip120 = AviSource("0326-120fps.avi") there is no effect at all, both clips are played back at 30fps, meaning that only a quarter of the 120fps clip has been shown by the time the 30fps clip is over. So how can I combine these two clips in the manner I want? I was unable to find any other internal or external filters that would help me do that. It seems to me that if ChangeFPS did what the manual says, it would be the right one for the job.

  Read the article

• Cannot Install Phusion Passenger 3.0.13 with Nginx 1.2.1

  - by LightBe Corp

  I installed gem Passenger which installed 3.0.13. Then I executed passenger-install-nginx-module which is what the Nginx instructions on http://www.modrails.com said to do. It installs the latest stable version which is 1.2.1 according to the Nginx official wiki page. I said to install Nginx to /usr/local/nginx (which is the default if you go to the nginx wiki website). I get the following errors: Undefined symbols for architecture x86_64: "_pcre_free_study", referenced from: _ngx_pcre_free_studies in ngx_regex.o ld: symbol(s) not found for architecture x86_64 collect2: ld returned 1 exit status make[1]: *** [objs/nginx] Error 1 make: *** [build] Error 2 -------------------------------------------- It looks like something went wrong Please read our Users guide for troubleshooting tips: /Users/server1/.rvm/gems/[email protected]/gems/passenger-3.0.13/doc/Users guide Nginx.html If that doesn't help, please use our support facilities at: http://www.modrails.com/ We'll do our best to help you. I have done searches for several hours trying to find a resolution. I tried the Google Group for Phusion Passenger but did not find anything. I do not know if there is a mismatch in version numbers or not. The documentation says nothing about this error.

  Read the article

• Live Screencast under Linux

  - by OmnipotentEntity

  I was having some difficulty with running a Live Screencast under Linux. I've found jtvlc and tried using that, but whenever I use it the stream comes out either blank or lagged with extremely high latency. I have a fast internet connection and a fast computer, but am I perhaps taxing it too much? Any ideas on what I could possibly be doing wrong? # 1. Get an account on http://www.justin.tv/ # 2. Copy streaming key from: http://www.justin.tv/broadcast/adv_other # 2. Install VLC: http://www.videolan.org/vlc/ # 3. Get Win/Mac/Lin Stream Client: \ # http://apiwiki.justin.tv/mediawiki/index.php/Linux_Broadcasting_API # 4. Adjust the vlc parameters to your liking and run VLC like this #!/bin/bash cvlc screen:// --input-slave=pulse:// \ --screen-width 1920 \ --screen-height 1080 \ --screen-fps 5 \ -v input_stream \ --sout='#duplicate{ dst="transcode{ scale=1, venc=x264{ keyint=60 }, vcodec=h264, vb=600, acodec=mp4a, ab=32, channels=2, samplerate=22050 } :rtp{dst=127.0.0.1,port=1234,sdp=file:///tmp/vlc.sdp} "}' \ --sout-transcode-threads=4 & sleep 2 # 5. Run JTVLC to stream like this: ./jtvlc/jtvlc omnipotententity censored /tmp/vlc.sdp # Notes: #- If you want to see what you're about to stream add 'dst=display, ' # before 'dst="transcode[' # More about the VLC parameters: http://wiki.videolan.org/Documentation:Modules/screen

  Read the article

• How to use SSH Public Key with PuTTY to connect to a Linux machine

  - by ysap

  I am trying to set a public SSH key connection from a Windows 7 machine to a Red-Hat Linux machine. The ultimate purpose is to use pscp (PuTTY's version of scp) from the command terminal w/o the need to type password repetitively. Following PuTTY's documentation and other online sources, I used PuTTYgen to generate a key pair. I then copied the generated public key to a ~/.ssh/authorized_keys file on the Linux machine (as far as I can tell, it runs OpenSSH server). To check the connection, I run PuTTY and set the username and private key file in the appropriate places in its GUI. However, when trying to connect using PuTTY's SSH, the connection uses the preset username, but I get an error message of "Server refused our key" and a prompt for the password. I then tried to copy-paste the public key text from PuTTYgen's GUI to the authorized_keys file, but it did not work either. How should I set up a public key connection form Win 7 to Linux? How do I use this with pscp (rather than PuTTY's ssh)?

  Read the article

• Mechanism behind user forwarding in ScriptAliasMatch

  - by jolivier

  I am following this tutorial to setup gitolite and at some point the following ScriptAliasMatch is used: ScriptAliasMatch \ "(?x)^/(.*/(HEAD | \ info/refs | \ objects/(info/[^/]+ | \ [0-9a-f]{2}/[0-9a-f]{38} | \ pack/pack-[0-9a-f]{40}\.(pack|idx)) | \ git-(upload|receive)-pack))$" \ /var/www/bin/gitolite-suexec-wrapper.sh/$1 And the target script starts with USER=$1 So I am guessing this is used to forward the user name from apache to the suexec script (which indeed requires it). But I cannot see how this is done. The ScriptAliasMatch documentation makes me think that the /$1 will be replaced by the first matching group of the regexp before it. For me it captures from (?x)^/(.* to ))$ so there is nothing about a user here. My underlying problem is that USER is empty in my script so I get no authorizations in gitolite. I give my username to apache via a basic authentication: <Location /> # Crowd auth AuthType Basic AuthName "Git repositories" ... Require valid-user </Location> defined just under the previous ScriptAliasMatch. So I am really wondering how this is supposed to work and what part of the mechanism I missed so that I don't retrieve the user in my script.

  Read the article

• Apache inflate application/ with mod_filter

  - by BGT

  I need to prevent pdf objects from being gzipped. Really, this only needs to take place if the request is from the Mozilla browser (but since I can't get something as seemingly simple as no-gzip for application/pdf, I figure it's wiser to start there). From looking at the apache documentation on mod_filter, I've got the following: <Location /> FilterDeclare gzipDeflate CONTENT_SET FilterDeclare gzipInflate CONTENT_SET FilterProvider gzipDeflate deflate req=User-Agent $Mozilla/ FilterProvider gzipInflate inflate resp=Content-Type $application/ FilterChain +gzipDeflate +gzipInflate </Location> From my testing, the gzipDeflate filter is doing its job and all the pages without the Content-Type starting with application are being gzipped. But, the gzipInflate doesn't seem to be working at all. I've inspected the response in Firebug and verified that the Content-Type being sent down is application/pdf. I'll go ahead and ask a potentially stupid question though: The response's Content-Type header in its entirety read "application/pdf; charset=Windows-1252". Does that make any sort of difference or is $application/ presumably enough to catch that? Any help is greatly appreciated. One other point, the URL that returns the pdf object does not have the .pdf extension. The pdf itself is stored in an Oracle database as a blob and appended to the page when appropriate (all the urls in the system use the same baseline). This was part of an original inquiry by a helpful member at stackoverflow who pointed me towards mod_filter and suggested I post the question here.

  Read the article

• Applying ACLs to a Dovecot public namespace

  - by larsks

  I have a public namespace define in my dovecot (dovecot-2.0.9) configuration that looks like this: namespace { type = public separator = . prefix = news. location = maildir:/var/spool/news subscriptions = no } I would like to make all the mailboxes in this namespace read-only. I've got the following configuration for the ACL plugin: plugin { acl = vfile:/etc/dovecot/acls:cache_secs=300 } After perusing the documentation, it seemed as if I had a mailfolder /var/spool/news/.foo.bar that I could place the following into /var/spool/news/.foo.bar/dovecot-acl: anyone rl But that doesn't have any affect. I also tried creating a file /usr/local/etc/dovecot/acls/news.foo.bar with the same contents, but that didn't do anything, either. I've turned on mail debugging: mail_debug = yes But the log doesn't produce anything that appears to be relevant to ACL processing. I'm curious to know if anyone has gotten this to work correctly and if so if you could provide some configuration examples. Also, if there's any way to do this that doesn't involve per-mailbox configuration (.e.g, the ability to apply an ACL to news.* or something), that would be awesome. Getting the documented behavior for default ACLs working would be a step in the right direction.

  Read the article

• What is the recommended glusterFS configuration for a growing website?

  - by montana

  Hello, I have a website that is tracking towards 50 million hits per day average, and within the next 3 months should be over 100 million hits per day. We are trying to use GlusterFS v 3.0.0 (with latest patches as of 1-17-2010) Currently, we've just upgraded to a load balancer environment that has 3 physical hosts with 6 Xen-Server 5.5u1 VM's (2 on each host) to serve webpage traffic. Each machine has 6 Raid-6 local storage drives (7200RPM-SATA). The old machine we came from had 1 mirrored SAS 10k drive. We also set up glusterFS currently with 3 bricks, one on each host, and it is serving the 6 VM's as clients. In testing, everything seemed fine. However when we went to production, it seemed that there just wasn't enough I/O's available to serve traffic even upwards of 15mil hits. Weeks prior, our old server was able to handle traffic, maxed out, at 20mil. Is there any recommended configurations for such an application, or things to be aware of that isn't apparent with their documentation at gluster.org for a site our size?

  Read the article

• OpenVZ with bridged interfaces and VLAN

  - by Deimosfr

  Hi, I've got a problem with OpenVZ with bridged VLAN. Here is my configuration: +------+ +-------+ +-----------+ +---------+ br0 |VE101 | | | | OpenBSD |----->| Debian |------->| | | WAN |--->| Router | | OpenVZ | +------+ | | | Firewall |----->| br0 br1 | br1 +------+ +-------+ +-----------+ +---------+------->|VE102 | |br0 | | |VLAN br0.110 +------+ v +---------+ |VE103.110| +---------+ I can't make VLAN work on br0 (br0.110) and I would like to understand why. I don't have any switch so no problem with unmanageable switch. I've configured a VLAN interface on OpenBSD in /etc/hostname.vlan110: inet 192.168.110.254 255.255.255.0 NONE vlan 110 vlandev sis1 And it seems to be working fine. I've also adapted my PF configuration to work with VLAN but I don't see any incoming traffic. On my Debian Lenny, here is my interfaces configuration : # The loopback network interface auto lo iface lo inet loopback # br0 auto br0 iface br0 inet static address 192.168.100.1 netmask 255.255.255.0 gateway 192.168.100.254 network 192.168.100.0 broadcast 192.168.100.255 bridge_ports eth0 bridge_fd 9 bridge_hello 2 bridge_maxage 12 bridge_stp off # VLAN 110 auto br0.110 iface br0.110 inet static address 192.168.110.1 netmask 255.255.255.0 network 192.168.110.0 gateway 192.168.110.254 broadcast 192.168.110.255 pre-up vconfig add br0 110 post-down vconfig rem br0.110 It looks OK, but when I start my VE, here is the message: ... Configure veth devices: veth103.0 Adding interface veth103.0 to bridge br0.110 on CT0 for VE103 can't add veth103.0 to bridge br0.110: Operation not supported VE start in progress... So I've got one error here. I've followed this documentation http://wiki.openvz.org/VLAN but it doesn't work. I've certainly missed something but I don't know why. Someone could help me please? Thanks

  Read the article

• Multiple rack apps on nginx + passenger, one as root, the other not...config help

  - by cannikin

  So I've got two apps I want to run on a server. One app I would like to be the "default" app--that is, all URLs should be sent this app by default, except for a certain path, lets call it /foo: http://mydomain.com/ -> app1 http://mydomain.com/apples -> app1 http://mydomain.com/foo -> app2 My two rack apps are installed like so: /var /www /apps /app1 app.rb config.ru /public /app2 app.rb config.ru /public app1 -> apps/app1/public app2 -> apps/app2/public (app1 and app2 are symlinks to their respective apps' public directories). This is the Passenger setup for sub URIs described here: http://www.modrails.com/documentation/Users%20guide%20Nginx.html#deploying_rack_to_sub_uri With the following config I've got /foo going to app2: server { listen 80; server_name mydomain.com; root /var/www; passenger_enabled on; passenger_base_uri /app1; passenger_base_uri /app2; location /foo { rewrite ^.*$ /app2 last; } } Now, how do I get app1 to pick up everything else? I've tried the following (placed after the location /foo directive), but I get a 500 with an infinite internal redirect in error.log: location / { rewrite ^(.*)$ /app1$1 last; } I hoped that the last directive would prevent that infinite redirect, but I guess not. /foo gets the same error. Any ideas? Thanks!

  Read the article

• SharePoint 2010 Enterprise wiki - [New page] missing

  - by icelava

  I am trying to ramp up knowledge on SharePoint deployment and usage (never did before), due to a direction to use SharePoint 2010 as a repository platform (wiki format) for our customer's infrastructure documentation. In my test virtual server, a new site of Enterprise wiki template was setup. Went into Site Actions Manage Site Features to activate Wiki Page Home Page. The default sub-web then went from /Pages to /SitePages and looks like the default Team template. The odd thing is the Site Actions is missing the New Page option. My colleague does not understand why this is the case, as it ought to be there. The original /Pages sub-web does have the option. What conditions are in play that influences the appearance of that option? UPDATE Another phenomenon observed is in the Site Actions View All Site Content view, the wiki document libraries listed in the grid will have their hyperlink (e.g. "Site Pages") lead straight to the direct default page. It would not show its own table listing of pages under that document library, unlike the original Pages document library, which expectedly show up as a listing. I wonder if this hints to any problems.

  Read the article

• Difference between CurrentClockSpeed and MaxClockSpeed

  - by Ben

  Rationale this belongs on ServerFault rather than StackOverflow - I already have my program which gets the value, I am querying the value returned and what it means. I have an in-house program which audits our company PCs, and one of the things it checks is the speed of the processor. To do this, it queries the Win32_Processor WMI class and gets the value of CurrentClockSpeed. We were playing with the data today and found an anomaly with some of the speeds being reported incorrectly (for example, CurrentClockSpeed said 1.0GHz, whereas the CPU name said Intel(R) Core(TM)2 CPU T5600 @ 1.83GHz [Confirmed it is in fact 1.83GHz]). I did a bit of digging on the internet and found this blog post which might explain what is going on. My initial thought was that I could change the program to instead get the value for MaxClockSpeed instead of CurrentClockSpeed, but Microsoft's documentation doesn't clearly define what this will return. What I mean by that is will this return a value which is its actual maximum speed (say if it were overclocked) but which it would not normally be running at, or would it return what I expect, which is its maximum speed under normal (not overclocked) conditions?

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Accessing a shared folder in Windows Server 2008 R2.

  - by Triztian

  Hello all, seems my involvement with computers has grown and I've found my self in the need to access a shared folder on a server. I've read some documentation and managed to set up the folder as a share, for this I created a local group and for now just one local user that has access to the share, the folder is in the public user folder and it's permissions should be (and I believe they are) read/write. The problem is that I can't connect from a remote machine I mean I don't know how the way it should be accessed, the server has a public IP and we use it also as a host to our website I don't know if that affects it though, the folder will be used as the "keeper" for the QuickBooks company files and has the database server manager installed. I've tried setting up a VPN Connection to the but no success. The server has a domain name a "http://www.example.com" that redirects to our website, I am unsure if it could be accessed that way, also the share has a location displayed when I right-click properties Heres what I've tried Setting up a VPN Connection (Windows Vista and 7) Got to the point where I got asked for credential and entered the user I created (which is not an admin) but I got a "Connection fail error 800" I suppose this is because in the domain field I entered the servers workgroup. right-click add network connection (Windows 7) Went through the wizard until I reached the point of entering the location, tried many things, the name in the share's properties(\\SOMETHING\Share), the http://www.example.com , the IP address I'm quite unfamiliar with this, so I have my guesses: Since the group and user are local they do not have access to the folder. The firewall in the server is blocking my connection. Anyways, any help and guidence is truly appreciated.

  Read the article

• emacs ORG-mode "headless" export-as commands?

  - by Seamus

  When I use org-export-as-latex or org-export-as-html orgmode turns my buffer into a .tex file or .html file. But I don't want all the extra junk that it adds to the file: I want to handle the documentclass and everything myself and just \input the org mode generated file. (Or the analogous things for html with php). So if my org file just has: * Section - Stuff - Things I want the org mode command to output just \section{Section} \begin{itemize} \item Stuff \item Things \end{itemize} Without any of the extra \tableofcontents junk that ORG adds to it. I know I could define my own kind of #+LaTeX_CLASS that could add the packages I want and so on, but I don't want to do things that way (and that wouldn't remove the \maketitle or the spurious \vspace* that ORG insists on inserting. Is there a command to do this "headless" parsing and converting? I had a look but it's not obvious from the documentation. Presumably some low level ORG command is doing the parsing and converting I want, but I couldn't find what it was called from looking at the docs and C-h pages... This is not a question about HTML or LaTeX but about emacs ORG mode. So don't kick it off to some other site...

  Read the article

• setting up tracd behind mod_proxy?

  - by FilmJ

  I'm having trouble setting up mod_proxy and tracd. Seems almost all the search results for this problem take me to the built-in trac documentation page that mentions it as an option. I have several VirtualServers already running on the box in question, so running tracd on port 80 or 443 is not an option, but I do want to make my trac server accessible on this machine without exposing an additional port via the firewall. Making things even more complicated is that I have multiple trac repositories being served by the same instance of tracd, and so I want to set it up so: http://trac.abc.com is proxy'd to localhost:8000/projects/abcproject, and http://trac.def.com is proxy'd to localhost:8000/projects/defproject. Currently, the setup I have below results in 100% 403 errors. The server is running as www-data and the directory where all trac files are stored is owned by www-data, AND tracd (as show below) is running as www-data, so not sure where it's getting hung up. The relevant configuration on /var/apache2/sites-enabled/trac.abc.com: ProxyPass / http://localhost:8000/abcproject ProxyPassReverse / http://localhost:8000/abcproject The relevant configuration on /var/apache2/sites-enabled/trac.def.com: ProxyPass / http://localhost:8000/defproject ProxyPassReverse / http://localhost:8000/defproject The command used to instantiate tracd: tracd -a defproject,/var/www/vhosts/trac-common/users.htdigest,DEFProject -a abcproject,/var/www/vhosts/trac-common/users.htdigest,ABCProject -p 8000 -b localhost -e /var/www/vhosts/trac-common/projects If I access the site at http://localhost:8000/ everything works fine, but if I try to access via any of the proxy'd hosts I end up with 403 at every turn. I've used mod_proxy successfully as described above for other servers, such as couchdb, so maybe this has to do with the headers sent by tracd??

  Read the article

• Virtualization in Ubuntu 9.10

  - by Jeff Dege

  I have an existing Centos 5 installation. I would like to upgrade to Ubuntu. Thing is, I don't want to be down for as long as it will take to get my entire environment moved over - software installed, connectivity configured, etc. I'd like to take it one step at a time. But I don't really want to keep rebooting back and forth from the new OS to the old OS. That's what I did last time I upgraded to a new OS, and it got old real fast. So, since my new MB is virtualization-ready (AMD Phenom II 945 quad-core), I figured I could create a virtual machine, under the new OS installation, that ran the old OS installation. The problem is that the documentation I've been able to find has been pretty sparse. I've found a lot of possibilities, and little info on which would be capable of doing what I want. I have a new Ubuntu 9.10 installation, and a second disk containing the Centos 5 installation. And I don't know where to go next. Any help would be appreciated.

  Read the article

• Finding matching columns in excel

  - by fakaff

  I've never used excel before so I need the simplest solution available, and this is a work assignment due this week so I didn't have time read much of the documentation. Basically, I have two tables, A and B, and they are both thousands of rows long. Description of my task: right now (since I don't know better) I'm manually doing this: Go to row i in table B. Select entries in columns B(a, b, c) of that same row. Look for a row in table A where column A(b) matches row B(a). Paste the entries of columns B(a) of row i at the end of the row found in the last step. Repeat for row i + 1. Example: row B(cat, dog, mouse) matches A(mammal, cat, Mr. Whiskers). So I would paste B after A and have A(mammal, cat, Mr. Whiskers, cat, dog, mouse). Note: I am not joining tables. I am merely extending table A by pasting row A(b) if row A(b) matches row B(a). Also, sometimes entries are spelled slightly differently. Using wildcards to search for candidates would be of help. As the description should let on, this task is very tedious and inefficient if I don't know how to automate some operations (there are thousands of entries). Any quick tips as to how to be more productive is a big help.

  Read the article

• Can't access Port 80 from external

  - by dewacorp.alliances

  Hi there I have configuration like this: NETGEAR MODEM LINKSYS ROUTER SERVERS In the modem, I've setup as bridging and all the traffic is controlling by this ROUTER. Prior to this setup, I can access website from external (port 80) plus exchange servers (mail) and https. But now with this configuration, I can only send/receive using Exhcange servers and access OWA (Outlook web access using port 443) .... and no internal websites from outside. This is my config for LINKSYS ROUTER Application | Start | End | Protocol | IP Address Ms Exchange | 25 | 25 | Both (TCP/UDP) | 192.168.100.8 Internets | 80 | 80 | Both (TCP/UDP) | 192.168.100.11 SSL | 443 | 443 | Both (TCP/UDP) | 192.168.100.8 Exchange | 110 | 110 | Both (TCP/UDP) | 192.168.100.8 192.168.100.11 is a UBUNTU web server that running the apache which controlling the virtual name (extranet, cms, test) to redirect to the different servers. As you can see, the home internet is only allowing public IP address. Now I test this schenarion in internal network work nicely. For instance. If I type in extranet.XXX.local it goes to the right applicatios or if I try CMS.XXX.local again it goes to the right one. I also asked to ISP just in case if they are blocking the inbound port 80 for unknown reason. They said no. So I didn't understand why this happens. I suspect the configuration that I have between MODEM ROUTER but I counldn't work what it is. I don't have a documentation of previous settings and I don't know if there is a port that I need to open as well. I am appreciated your comment

  Read the article

• Changing PATH Environment Variable for all Users. (Ubuntu)

  - by Wally Glutton

  I recently compiled Ruby Enterprise Edition (REE) on an Ubuntu 8.04 server. I would like to update my PATH to ensure this new version of Ruby (found in /opt/ruby_ee/bin) supersedes the older version in /usr/local/bin. (I still want the old version around, though.) I would like these PATH changes to affect all users and crontabs. Attempted Solution #1: The REE documentation recommends placing the REE bin folder at the beginning of the global PATH in /etc/environment. I altered the PATH in this file to read: PATH="/opt/ruby_ee/bin:/usr/local/sbin:/usr/local/bin:/usr/sbin:/usr/bin:/sbin:/bin:/usr/games" This did not affect my PATH at all. Attempted Solution #2: Next I followed these instructions and updated the PATH setting in /etc/login.defs and /etc/crontab. (I did not change /etc/sudoers.) This didn't affect my PATH either, even after logging out and rebooting the server. Other information: I seem to be having the same problem described here. I'm testing using the commands "echo $PATH" and "ruby -v". My shell is bash. My .bashrc doesn't override my PATH. Yes, I have heard of the Ruby Version Manager project. ;)

  Read the article

• Problems installing Windows service via Group Policy in a domain

  - by CraneStyle

  I'm reasonably new to Group Policy administration and I'm trying to deploy an MSI installer via Active Directory to install a service. In reality, I'm a software developer trying to test how my service will be installed in a domain environment. My test environment: Server 2003 Domain Controller About 10 machines (between XP SP3, and server 2008) all joined to my domain. No real other setup, or active directory configuration has been done apart from things like getting DNS right. I suspect that I may be missing a step in Group Policy that says I need to grant an explicit permission somewhere, but I have no idea where that might be or what it will say. What I've done: I followed the documentation from Microsoft in How to Deploy Software via Group Policy, so I believe all those steps are correct (I used the UNC path, verified NTFS permissions, I have verified the computers and users are members of groups that are assigned to receive the policy etc). If I deploy the software via the Computer Configuration, when I reboot the target machine I get the following: When the computer starts up it logs Event ID 108, and says "Failed to apply changes to software installation settings. Software changes could not be applied. A previous log entry with details should exist. The error was: An operations error occurred." There are no previous log entries to check, which is weird because if it ever actually tried to invoke the windows installer it should log any sort of failure of my application's installer. If I open a command prompt and manually run: msiexec /qb /i \\[host]\[share]\installer.msi It installs the service just fine. If I deploy the software via the User Configuration, when I log that user in the Event Log says that software changes were applied successfully, but my service isn't installed. However, when deployed via the User configuration even though it's not installed when I go to Control Panel - Add/Remove Programs and click on Add New Programs my service installer is being advertised and I can install/remove it from there. (this does not happen when it's assigned to computers) Hopefully that wall of text was enough information to get me going, thanks all for the help.

  Read the article

• Redirect 301 fails with a path as destination

  - by Martijn Heemels

  I'm using a large number of Redirect 301's which are suddenly failing on a new webserver. We're in pre-production tests on the new webserver, prior to migrating the sites, but some sites are failing with 500 Internal Server Error. The content, both databases and files, are mirrored from the old to the new server, so we can test if all sites work properly. I traced this problem to mod_alias' Redirect statement, which is used from .htaccess to redirect visitors and search engines from old content to new pages. Apparently the Apache server requires the destination to be a full url, including protocol and hostname. Redirect 301 /directory/ /target/ # Not Valid Redirect 301 /main.html / # Not Valid Redirect 301 /directory/ http://www.example.com/target/ # Valid Redirect 301 /main.html http://www.example.com/ # Valid This contradicts the Apache documentation for Apache 2.2, which states: The new URL should be an absolute URL beginning with a scheme and hostname, but a URL-path beginning with a slash may also be used, in which case the scheme and hostname of the current server will be added. Of course I verified that we're using Apache 2.2 on both the old and the new server. The old server is a Gentoo box with Apache 2.2.11, while the new one is a RHEL 5 box with Apache 2.2.3. The workaround would be to change all paths to full URL's, or to convert the statements to mod_rewrite rules, but I'd prefer the documented behaviour. What are your experiences?

  Read the article

• Exchange 2010 Hub Transport Role Fails - Registry Keys Missing?

  - by DKNUCKLES

  I've inherited an attempted Exchange 2010 implementation from a colleague that apparently failed. I've almost managed to bring it back from the dead, but the Hub Transport role fails to install with the following error [10/06/2012 02:30:44.0119] [2] Beginning processing Set-LocalPermissions -Feature:'Bridgehead' [10/06/2012 02:30:44.0166] [2] [ERROR] Unexpected Error [10/06/2012 02:30:44.0166] [2] [ERROR] The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0182] [2] Ending processing Set-LocalPermissions [10/06/2012 02:30:44.0182] [1] The following 1 error(s) occurred during task execution: [10/06/2012 02:30:44.0182] [1] 0. ErrorRecord: The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0182] [1] 0. ErrorRecord: System.ArgumentException: The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.GetTargetRegistryKey(XmlNode targetNode) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.ChangePermissions[TTarget,TSecurity,TAccessRule,TRights](XmlNode targetNode, Dictionary`2 rightsDictionary, GetTarget`1 getTarget, GetOrginalPermissionsOnTarget`2 getOrginalPermissionsOnTarget, SetPermissionsOnTarget`2 setPermissionsOnTarget, CreateAccessRule`2 createAccessRule, AddAccessRule`2 addAccessRule, RemoveAccessRuleAll`1 removeAccessRuleAll) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetPermissionsOnCurrentLevel[TTarget,TSecurity,TAccessRule,TRights](XmlNode permissionSetNode, String targetType, Dictionary`2 rightsDictionary, GetTarget`1 getTarget, GetOrginalPermissionsOnTarget`2 getOrginalPermissionsOnTarget, SetPermissionsOnTarget`2 setPermissionsOnTarget, CreateAccessRule`2 createAccessRule, AddAccessRule`2 addAccessRule, RemoveAccessRuleAll`1 removeAccessRuleAll) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetPermissionsOnCurrentLevel(XmlNode permissionSetNode) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.SetFeaturePermissions(String feature) at Microsoft.Exchange.Management.Deployment.SetLocalPermissions.InternalProcessRecord() [10/06/2012 02:30:44.0197] [1] [ERROR] The following error was generated when "$error.Clear(); Set-LocalPermissions -Feature:"Bridgehead" " was run: "The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE".". [10/06/2012 02:30:44.0197] [1] [ERROR] The registry key "SOFTWARE\Microsoft\ExchangeServer\v14\Transport" does not exist under "HKEY_LOCAL_MACHINE". [10/06/2012 02:30:44.0197] [1] [ERROR-REFERENCE] Id=BridgeheadLocalPermissionsComponent___2e2dbc2a97cb4429bc2074edc50bedbd Component=EXCHANGE14:\Current\Release\Shared\Datacenter\Setup [10/06/2012 02:30:44.0197] [1] Setup is stopping now because of one or more critical errors. [10/06/2012 02:30:44.0197] [1] Finished executing component tasks. [10/06/2012 02:30:44.0244] [1] Ending processing Install-BridgeheadRole I've been unable to find any documentation on how to resolve this issue. Any help would be appreciated.

  Read the article

< Previous Page | 341 342 343 344 345 346 347 348 349 350 351 352  | Next Page >