Search Results

Search found 11231 results on 450 pages for 'bad alloc'.

Page 346/450 | < Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >

• Postfix does not work after setting server hostname from plesk

  - by Michael

  I have recently set my server hostname from localhost.localdomain to xx.mydomain.com from the plesk control panel. However after doing this change postfix has stopped working, I tried restarting and regenerating the config files but to no avail. I am not familiar with postfix but I believe there is a setting to be changed in main.cf. Here are the relevant errors I receive: postfix/postfix-script: starting the Postfix mail system postfix/master: daemon started -- version 2.8.4, configuration /etc/postfix postfix/cleanup: fatal: host/service localhost/12768 not found: Name or service not known postfix/pickup: warning: maildrop/E5559996219: error writing 4FA2C996217: queue file write error postfix/master: warning: process /usr/libexec/postfix/cleanup pid 15334 exit status 1 postfix/master: warning: /usr/libexec/postfix/cleanup: bad command startup -- throttling Any ideas? EDIT Setting it back to localhost.localdomain makes it work again. The only references to localhost/12768 I can find in main.cf are: smtpd_milters = inet:localhost:12768 non_smtpd_milters = inet:localhost:12768 Should something be changed here? These two lines stay the same when I change the hostname. EDIT If I comment out the two mail filter lines (the ones shown above) and restart, postfix works with the new hostname. However this is obviously not the ideal solution...

  Read the article

• Why do I get a DegradedArray event with mdadm

  - by azera

  Hello Just so we're clear on what's happening: I bought 4 new sata 2 drives, with the intent of using them in a raid5 all drive are fully recognised by both my bios and my linux box (gentoo) I created a raid5 array, fiddled a bit with it to understand how it works, how to monitor ect At some point, this triggered a degradedarray event, even though the array is brand new. I tried to stopping the array and recreating a new array with the same drive but the new array starts degraded too. here is what I used to create it mdadm --create -l5 -n4 /dev/md/md0-r5 /dev/sdb /dev/sdd /dev/sde /dev/sdf here are the output from my /proc/mdstat and mdadm --detail --scan **mdstat** Personalities : [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md127 : active raid5 sdf[4] sde[2] sdd[1] sdb[0] 4395415488 blocks level 5, 64k chunk, algorithm 2 [4/3] [UUU_] [>....................] recovery = 2.8% (41689732/1465138496) finish=890.3min speed=26645K/sec unused devices: <none> **detail** ARRAY /dev/md/md0-r5 metadata=0.90 spares=1 UUID=453e2833:81f22a74:64188b84:66721085 As such I have a couple questions: does a raid5 array always start in degraded mode at first ? why does sdf have the number 4 between bracket instead of 3, why does it see a spare disk and why is the 4th drive marked with _ instead of U ? (bad configuration ?) How can I recreate the array from scratch, do i have to format each drive on its own before recreating it ? Thanks for any help, I'm not sure about what I should do at the moment

  Read the article

• Computer locking up, looking for bootable hardware diagnostic tool.

  - by Carl Menke

  Well today I helped my friend build a computer. All went pretty well until we got to installing Win7. Thing is, we thought, it was crashing constantly. I adjusted pretty much every setting in the BIOS and removed as much hardware as possible to try and prevent a crash. No dice. So far I've tried running an Ubuntu live cd without the harddrive installed. Nope, crashed on boot. And then I just tried Microsoft's ram utility disk and it eventually locked up on that (the ram passed though). So it seems to me like it's either the CPU (AMD PhenomII x3) or the motherboard that could be bad, but I don't know how to test them individually for problems. I thought it could be a overheating issue, but the BIOS reports that the CPU temp is fine idling around 34C. Any advice or diagnostic disk that could help me out? TL;DR: Computer locks up frequently during use (cannot even boot/install an operating system), memory is fine, probably CPU or Mobo, BIOS says CPU temps are fine. What should I try?

  Read the article

• Windows 7: Setting up backup to an external hard drive on another computer on the network

  - by seansand

  I have an external hard drive connected to a Windows 7 (Home Edition) computer. I have another computer (with Windows 7 Ultimate), and I want to have the Windows 7 Ultimate back up to the same external hard drive, without having to disconnect and move the external hard drive from the Home Edition PC. When I get to the "Set up backup" dialog within Windows 7, it asks me where to save the backup. I select "Save on a network". However, when I enter "\\computername\harddrivename" under Browse, the "OK" button remains grayed out. The button remains grayed out unless I also enter a Username and Password under "Network credentials". However, the account I have on the other computer doesn't have a password for it. To un-gray out the button I must enter a fake password, allowing me to click "OK", but then obviously I get a "bad password" error. Does anyone know how to get around this problem? (Seems kind of ridiculous.) I made sure that the security settings with the external hard drive on the other computer are full access to Everyone, so permissions is not the problem. I also thought about using Homegroup instead of the regular security settings, but there is no obvious way to go about it that way, either.

  Read the article

• Abysmal transfer speeds on gigabit network

  - by Vegard Larsen

  I am having trouble getting my Gigabit network to work properly between my desktop computer and my Windows Home Server. When copying files to my server (connected through my switch), I am seeing file transfer speeds of below 10MB/s, sometimes even below 1MB/s. The machine configurations are: Desktop Intel Core 2 Quad Q6600 Windows 7 Ultimate x64 2x WD Green 1TB drives in striped RAID 4GB RAM AB9 QuadGT motherboard Realtek RTL8810SC network adapter Windows Home Server AMD Athlon 64 X2 4GB RAM 6x WD Green 1,5TB drives in storage pool Gigabyte GA-MA78GM-S2H motherboard Realtek 8111C network adapter Switch dLink Green DGS-1008D 8-port Both machines report being connected at 1Gbps. The switch lights up with green lights for those two ports, indicating 1Gbps. When connecting the machines through the switch, I am seeing insanely low speeds from WHS to the desktop measured with iperf: 10Kbits/sec (WHS is running iperf -c, desktop is iperf -s). Using iperf the other way (WHS is iperf -s, desktop iperf -c) speeds are also bad (~20Mbits/sec). Connecting the machines directly with a patch cable, I see much higher speeds when connecting from desktop to WHS (~300 Mbits/sec), but still around 10Kbits/sec when connecting from WHS to the desktop. File transfer speeds are also much quicker (both directions). Log from desktop for iperf connection from WHS (through switch): C:\temp>iperf -s ------------------------------------------------------------ Server listening on TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [248] local 192.168.1.32 port 5001 connected with 192.168.1.20 port 3227 [ ID] Interval Transfer Bandwidth [248] 0.0-18.5 sec 24.0 KBytes 10.6 Kbits/sec Log from desktop for iperf connection to WHS (through switch): C:\temp>iperf -c 192.168.1.20 ------------------------------------------------------------ Client connecting to 192.168.1.20, TCP port 5001 TCP window size: 8.00 KByte (default) ------------------------------------------------------------ [148] local 192.168.1.32 port 57012 connected with 192.168.1.20 port 5001 [ ID] Interval Transfer Bandwidth [148] 0.0-10.3 sec 28.5 MBytes 23.3 Mbits/sec What is going on here? Unfortunately I don't have any other gigabit-capable devices to try with.

  Read the article

• VMWare Workstation Linux Host performance tuning

  - by Hoghweed

  I need to improve my linux hosted vmware workstation for using multiple virtual machines at the same time. I feel very stupid I lost a great blog post link which I found last month (and I'm not able to find it again..) so I try to ask here if anyone can help me: This is my host (laptop): 16GB DDR3 Ram HDD Hybrid 750GB 7200 (8GB SSD Cache) Mint 15 x64 Kernel 3.9.7 swappiness set to 10 The above are the important things about the host. So, My need is the ability to run 2 or 3 VMs at the same time. The lack of performance is about the disk, The last time from that blog post I lost, I setup /tmp to be mounted ad a memory partition and in my previous installation that was good, now I'm not able to find a good solution to tweak the things. I think with 16GB o RAM there will be no problems to run multiple VMs, but whe they start to swap or use the /tmp things going bad (guest cursor going too fast after a freeze, guest freeze and so on) Anyone can help me to fit a good host tweak and configuration to get better performance? Thanks in advance

  Read the article

• Copy from CDROM is very slow in Ubuntu

  - by ???

  I'm using the command to copy CDROM image: # dd if=/dev/sr0 of=./maverick.iso But it's very slow, at about 350k bytes/sec. I've searched the google, and try the command # hdparm -vi /dev/sr0 /dev/sr0: HDIO_DRIVE_CMD(identify) failed: Bad address IO_support = 1 (32-bit) readonly = 0 (off) readahead = 256 (on) HDIO_GETGEO failed: Inappropriate ioctl for device Model=DVD-ROM UJDA775, FwRev=DA03, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=unknown, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4 DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2 AdvancedPM=no Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3: ATA/ATAPI-1,2,3,4,5 * signifies the current active mode Seems like DMA is already on. And a device test gives: # hdparm -t /dev/sr0 /dev/sr0: Timing buffered disk reads: 2 MB in 6.58 seconds = 311.10 kB/sec # sudo hdparm -tT /dev/sr0 /dev/sr0: Timing cached reads: 2 MB in 2.69 seconds = 760.96 kB/sec Timing buffered disk reads: m 4 MB in 5.19 seconds = 789.09 kB/sec The CD-ROM device and disc should be okay because I can copy it very fast in Windows, using UltraISO utility. So I guess there is something not configured right in Ubuntu, is it?

  Read the article

• Remote Desktop to Server 2008 fails from one particular Win7 client

  - by Jesse McGrew

  I have a VPS running Windows Web Server 2008 R2. I'm able to connect using Remote Desktop from my home PC (Windows 7), personal laptop (Windows 7), and work laptop (Windows XP). However, I cannot connect from my work PC (Windows 7). I receive the error "The logon attempt failed" in the RDP client, and the server event log shows "An account failed to log on" with this explanation: Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: username Account Domain: hostname Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc0000064 Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: JESSE-PC Source Network Address: - Source Port: - Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 I can connect from the offending work PC if I start up Windows XP Mode and use the RDP client inside that. The server is part of a domain but my account is local, so I'm logging in using a username of the form hostname\username. None of the clients are part of a domain. The server uses a self-signed certificate, and connecting from home I get a warning about that, but connecting from work I just get the logon error.

  Read the article

• Hard Drive benchmark values show write very very slow

  - by John

  I recently started to have issues with my laptop being very slow. I ran a hard drive benchmarking tool (by ATTO) that showed that the write speed was very very slow on my boot drive. I ran the same benchmark on my usb drive and it was 650 times faster than my boot drive when it came to writing. Reading is very fast/normal on both. I swapped out an identical drive and ran the same benchmark. This time the drive showed proper write speed. Thinking that I had a hard drive going bad I cloned the old one onto the new one. I managed to clone the problem too. Anyone have any ideas on what in WinXP SP3 might be causing the write issues? I am on a corporate network and we have commercial anti-virus software installed. (AVG I think) I regularly run defraggler and have about 40 gig free on a 100 gig drive. The machine has 4 gigs of memory. Any ideas? TIA J

  Read the article

• Group Policy Software Installs Too Silent on Windows 7

  - by jonblock

  I'm trying to migrate a Windows XP deployment process to Windows 7. The process has been surprisingly smooth, after figuring out how to bring up a base system. We rely heavily on Group Policy software installation, which in XP can mean long periods on any given morning sitting around watching the machine install new updates. At least the typical Windows Installer message shows the user that something is indeed happening. As far as I can tell, Windows 7 retains the startup installation process (good), but eliminates the on-screen message to indicate what's happening (bad). All a user will see, possibly for a half-hour or more if they haven't restarted for a while, is the electric hamster wheel and the words "Please wait...". I forsee a significant increase in support calls... If you're familiar with msiexec.exe parameters, XP behaves like /qb-, and 7 behaves like /qn. I want the /qb- behavior back. Is there a way to re-enable the Windows Installer notices for Group Policy startup installations?

  Read the article

• SMTP error goes directly to Badmail directory after Queue

  - by Sergio López

  This is the error I got in the .BDR Unable to deliver this message because the follow error was encountered: "This message is a delivery status notification that cannot be delivered.". The specific error code was 0xC00402C7. The message sender was <. The message was intended for the following recipients. [email protected] This is the .bad file I got in the badmail error, Can anyone help me ? I´m getting this error from every mail I try to deliver from several php apps and other apps, the relay is only for 2 ip adresses 127.0.0.1 and the server ip, I telnet the smtp and it seems to work fine the mail go to the queue folder... Im stucked From: postmaster@ALRSERVER02 To: [email protected] Date: Mon, 22 Aug 2011 18:39:38 -0500 MIME-Version: 1.0 Content-Type: multipart/report; report-type=delivery-status; boundary="9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02" X-DSNContext: 7ce717b1 - 1378 - 00000002 - C00402CF Message-ID: Subject: Delivery Status Notification (Failure) This is a MIME-formatted message. Portions of this message may be unreadable without a MIME-capable mail program. --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: text/plain; charset=unicode-1-1-utf-7 This is an automatically generated Delivery Status Notification. Delivery to the following recipients failed. [email protected] --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/delivery-status Reporting-MTA: dns;ALRSERVER02 Received-From-MTA: dns;ALRSERVER02 Arrival-Date: Mon, 22 Aug 2011 18:39:38 -0500 Final-Recipient: rfc822;[email protected] Action: failed Status: 5.3.5 --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02 Content-Type: message/rfc822 Received: from ALRSERVER02 ([74.3.161.94]) by ALRSERVER02 with Microsoft SMTPSVC(7.0.6002.18264); Mon, 22 Aug 2011 18:39:38 -0500 Subject: =?utf-8?Q?[MantisBT]_Reinicializaci=C3=B3n_de_Contrase=C3=B1a?= To: [email protected] X-PHP-Originating-Script: 0:class.phpmailer.php Date: Mon, 22 Aug 2011 17:39:38 -0600 Return-Path: [email protected] From: Alr Tracker Message-ID: X-Priority: 3 X-Mailer: PHPMailer 5.1 (phpmailer.sourceforge.net) MIME-Version: 1.0 Content-Transfer-Encoding: 8bit Content-Type: text/plain; charset="utf-8" X-OriginalArrivalTime: 22 Aug 2011 23:39:38.0020 (UTC) FILETIME=[C182E640:01CC6124] Si solicitó este cambio, visite la siguiente URL para cambiar su contraseña: Usuario: slopez Dirección IP remota: 189.191.159.86 NO RESPONDA A ESTE MENSAJE --9B095B5ADSN=_01CC61236DC6DEED00000001ALRSERVER02--

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Windows XP corrupts registry every several hours

  - by Ilya Kazakevich

  There is a Dell XPS 400 with Windows Media Center installer. It is installed on RAID (Intel Matrix Storage) which is built-in chipset south bridge. Raid has two 150 Gb WDC drivers connected as mirror. All drivers and updates are installed( sp3 and so on). A week ago PC changed its video mode to 256 colors (like VESA mode) and after several moments I got BSOD: c000021a: 0xc0000005 Doctor watson did not create dump although it is installed as default debugger. After reboot it said that config file is missing or corrupted. So, I boot to recovery console and found that registry file (config) is so small. I've replaced it with one from recovery point and windows booted sucessfully. But after about 3 hrs -- it has crashed again in the same wat! I look in event viewer: is said that Explorer.exe failed to open \global??\DLIAFS. I look in winobj, and found that it is a device. I made "deny from everyone" for this device ACL, and after several hours my windows crashed. I restored registry, boot again and there was no error about DLIAFS. I did full chkdsk and it did not found anything bad. But I found event about error paging to \Harddrive1\D. I do not have pagefile there, but I thought I should check my disk again. Unfortunatelly I cannt use smart tools for RAID, but I downloaded latest software from Intel (it can do the same things like RAID bios can but from windows). It verified my disks, found some errors, fix them, than I rebooted. And it crashed again. I am lost. What (except kernel debugging) could be done here? Thanks

  Read the article

• Blinking power button

  - by Mike Ramsey

  A friend asked me to look at his Gateway DX4640 desktop. When he presses the power button, power goes to the mobo (NVIDIA nForce 630i MCP73PV, GeForce 7100 chipset) and the CPU fan starts spinning. The power button slowely blinks on and off (blue) and the screen briefly says no signal and then goes black. And nothing else; no post code beeps. My initial two conjectures were: 1. Vista was stuck in sleep/hibernation mode, or 2. A power off had left the mobo in a bad state. The fix for both is to: a) Unplug the AC power cord b) hold the power button for 30 second to fully discharge the mobo It didn't help. I left the system unplugged from AC power for an hour. No change. I am out of ideas. Has anybody seen anything like this before? What does a blinking blue power button mean? How can I get more data points to guide trouble shooting? --Thank you, --Mike

  Read the article

• PHP crashing during oAuth scripts

  - by FunkyChicken

  I just installed Nginx 1.2.4 and PHP 5.4.0 (from svn) (php fpm). CentOs 5.8 64 The problem I have is that PHP crashes the moment I run any social oAuth scripts. I have tried to log into Facebook, Twitter and Google with various scripts that I know work on my other servers. When I load the scripts I get a 502 error from Nginx. And I find these errors in the log: in php-fpm log: WARNING: [pool www] child 23821 exited on signal 11 (SIGSEGV) after 1132.862984 seconds from start in nginx log: ERROR: recv() failed (104: Connection reset by peer) while reading response header from upstream From what I can see, it goes wrong when PHP tries to make a request to any of the oAuth servers. https://github.com/mahmudahsan/PHP-SDK-3.0---Graph-API-base-Facebook-Connect-Tutorial-Source for example is one of the scripts that works perfectly on my other machines, but causes PHP to crash. I found: http://stackoverflow.com/questions/3616191/nginx-php-fpm-502-bad-gateway which seems to be a similar problem, but I cannot find a way to solve it. +++ UPDATE +++ Now I have been doing some debugging in 1 of the scripts that is playing up. If you go to line 808 http://pastebin.com/gSnzRtXb it runs the curl_exec() command. When that is ran, it crashes. If i echo'test';exit; just above that line, it echo's correctly, if i do it below that line, php crashes. Which means it's that line 808 which causes the crash. So I made a very simple script to do some testing: http://pastebin.com/Rshnyhcm which also uses curl_exec, but that runs just fine. So I started to dig deeper into that query from the facebook script to see what values the $opts array contains from line 806. Output of that array is: http://pastebin.com/Cq9ffd3R What the problem is, I still have no clue :(

  Read the article

• CloudFlare dashboards empty, or performance issues

  - by Katafalkas

  I wanted to test CloudFlare performance so I set my image gallery domain on it and started testing. I have added PageRules for caching. And chose the Security: Essentially Off. I checked NS check tools and they say that my domain name is propagated with CloudFlare. For testing purpose I created a link that loads 200 images from that server, and was using loads.in website to determine how much it is faster. After trying few regions, I noticed that there were no improvement in loading speed. So I looked up the dashboards, and it was empty. I am not sure if I am doing something wrong, or made some error in my setup, or it takes few days to start caching or working properly, but at the moment - after a day of testing - dashboards are empty. Also the NS check tools sais that all name servers are propagated to CloudFlare and working fine. So I assume I got a bad performance because it is simply not working. I sent a letter to CloudFlare support team, but did not get any straight answer. So essentially my question is: Anyone has any experience with CloudFlare ? How long does it take for it to start caching static content to CDN ? Or there is simply something I am doing wrong ?

  Read the article

• Clipboard bug in Wordpad in Windows 7 (accidentally pasting large file into application)

  - by frenchglen

  In Win7, I use Wordpad, and I really like it. For my needs it's lean and fast, yet has the formatting functionalities I'm after when working on my TXT/RTF files on a daily basis. I don't intend to change text editors. There's a really bad bug which has ALWAYS plagued me. If you have a large file contained in the clipboard, like a 238MB FLAC file, and you accidentally paste it into Wordpad for whatever reason - it hangs the application for a VERY long time (like 2 hours, it depends on how big the file is, because it tries to 'handle' it). You either have to close the application and lose any unsaved changes, or go do something else until the item has finished pasting into Wordpad (it actually eventually drops the file's icon in wordpad just like how it appears in Windows Explorer). It's a Windows bug, a Wordpad bug. Is there some solution for this? Or is the problem fixed in Windows 8 (if anyone can tell me)? .....I'm not going to try out Win8 myself, merely to answer this question - that's what I'm asking it on SuperUSer for! I'm really hoping it's one of those little-yet-big things that they've fixed in Win8 (like removing the 255-character file path limit in Explorer, which is awesome). Thank you for your help, if you have Win8 handy and can test this. :)

  Read the article

• Cyrus: In practical terms, how do end users administer their shared mailboxes?

  - by Nick

  Let's say we have four customer service reps: Billy, Bob, Joe, and Tom. Tom is the department manager. There's a shared Customer Service mailbox on the Cyrus server that they all have access to. Tom, as the manager also has administrative privileges for the shared mailbox. They decide they want to create sub-folders a certain way, and Tom creates them. They're all running Thunderbird, so Tom right-clicks the main folder and chooses "New Subfolder". Now Tom has the Subfolders he needs and the other sales reps have... nothing! Because Cyrus created the Subfolders giving Tom "Full Access" permissions, and everyone else gets no access. So how does Tom give the other reps in his department access to the new folders? As far as Cyrus is concerned, Tom has permission to grant others access to his new mailboxes- But as far as I can tell, there's no option in Thunderbird for granting mailbox permissions. An IT staff member should not have to receive a support request every time someone wants to add a Subfolder to a shared mailbox. That's why we make certain users into mailbox admins in the first place! But asking (non-technical) users to SSH into an IMAP server to run cyradm seems like a bad idea too. Certainly someone has found a solution for this dilemma. Perhaps a Thunderbird extension for setting Cyrus permissions? Or something like umask that forces subfolders to have identical permissions to their parents on creation? And related, what about Sieve configuration? Is there anyway that can be done from the client machine too? Thanks, Nick

  Read the article

• Forcing a particular SSL protocol for an nginx proxying server

  - by vitch

  I am developing an application against a remote https web service. While developing I need to proxy requests from my local development server (running nginx on ubuntu) to the remote https web server. Here is the relevant nginx config: server { server_name project.dev; listen 443; ssl on; ssl_certificate /etc/nginx/ssl/server.crt; ssl_certificate_key /etc/nginx/ssl/server.key; location / { proxy_pass https://remote.server.com; proxy_set_header Host remote.server.com; proxy_redirect off; } } The problem is that the remote HTTPS server can only accept connections over SSLv3 as can be seen from the following openssl calls. Not working: $ openssl s_client -connect remote.server.com:443 CONNECTED(00000003) 139849073899168:error:140790E5:SSL routines:SSL23_WRITE:ssl handshake failure:s23_lib.c:177: --- no peer certificate available --- No client certificate CA names sent --- SSL handshake has read 0 bytes and written 226 bytes --- New, (NONE), Cipher is (NONE) Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE --- Working: $ openssl s_client -connect remote.server.com:443 -ssl3 CONNECTED(00000003) <snip> --- SSL handshake has read 1562 bytes and written 359 bytes --- New, TLSv1/SSLv3, Cipher is RC4-SHA Server public key is 1024 bit Secure Renegotiation IS NOT supported Compression: NONE Expansion: NONE SSL-Session: Protocol : SSLv3 Cipher : RC4-SHA <snip> With the current setup my nginx proxy gives a 502 Bad Gateway when I connect to it in a browser. Enabling debug in the error log I can see the message: [info] 1451#0: *16 peer closed connection in SSL handshake while SSL handshaking to upstream. I tried adding ssl_protocols SSLv3; to the nginx configuration but that didn't help. Does anyone know how I can set this up to work correctly?

  Read the article

• Finding ALL currently used IP addresses of Website

  - by Patrick R

  What steps would you take to discover all (or close to all) IP addresses that are currently used by a website? How would you be as exhaustive as possible without calling a website admin and asking for the list of IP addresses? ;) nslookup works but will vary based on dns server queried. whois is another good tool. Dig, not bad. Let's use Facebook for example. I'm blocking that site for the majority our our company's users, but some are approved for "research". I can not easily use OpenDNS because we all appear to come from the same request IP address. I could change that but don't want to add more vlans than I already have. I also could use block something like regex facebook1 "facebook\.com" (I'm running a cisco firewall) but that's pretty easy to sidestep. All that being said, I'm asking about specifically about finding ip addresses for a domain and not for other methods that I can block a domain name.

  Read the article

• YUM error. Is this a cert error

  - by Julia Roberts

  Nov 13 13:38:57 host abrt: detected unhandled Python exception in '/usr/bin/yum' Nov 13 13:38:57 host abrtd: New client connected Nov 13 13:38:57 host abrt-server[3508]: Saved Python crash dump of pid 3151 to /var/spool/abrt/pyhook-2012-11-13-13:38:57-3151 Nov 13 13:38:57 host abrtd: Directory 'pyhook-2012-11-13-13:38:57-3151' creation detected Nov 13 13:38:57 host abrtd: Can't load public GPG key /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-beta Nov 13 13:38:57 host abrtd: Can't load public GPG key /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-legacy-former Nov 13 13:38:57 host abrtd: Can't load public GPG key /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-legacy-release Nov 13 13:38:57 host abrtd: Can't load public GPG key /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-legacy-rhx Nov 13 13:38:57 host abrtd: Can't load public GPG key /etc/pki/rpm-gpg/RPM-GPG-KEY-redhat-release Nov 13 13:38:57 host abrtd: Package 'yum' isn't signed with proper key Nov 13 13:38:57 host abrtd: 'post-create' on '/var/spool/abrt/pyhook-2012-11-13-13:38:57-3151' exited with 1 Nov 13 13:38:57 host abrtd: Corrupted or bad directory /var/spool/abrt/pyhook-2012-11-13-13:38:57-3151, deleting There is also nothing in the crash dump file. Ideas? yum update Loaded plugins: fastestmirror, rhnplugin, security An error has occurred: Internal Server Error See /var/log/up2date for more information Is yum broken

  Read the article

• System recognizes admin password on the Welcome screen but not when elevating

  - by Lee C.

  I set up Windows 7 with a couple of standard accounts, and an administrator account (called Odin). I can log in to Odin just fine from the Welcome screen. While logged into Odin I can do anything that requires administrator privileges without a password: just hit Yes in the User Account Control dialog. If I am logged into one of the other accounts and I do something that requires elevation (e.g. most installers, and some control panel functionality), then Windows presents me with a User Account Control dialog asking "Do you want to allow the following program to make changes to this computer? To continue, type an administrator password, and then click Yes." The account shown in this dialog is Odin, so I enter Odin's password. But Windows redisplays the dialog with the message "Logon failure: unknown user name or bad password." This always happens, and has done so for many months, probably since I first got the computer. Why does Odin's password work from the Welcome screen, but not when elevating? Please note that I am not asking how to recover Odin's password. I remember the password I originally set for Odin, and it works as it should from the Welcome screen, but is not recognized when elevating. The password has no funny characters, just letters and digits. Thanks!

  Read the article

• Desktop bigger than screen

  - by alex

  I am using MSI U115 11" netbook (OS: Windows XP Home, graphics card: Intel Graphics Media Accelerator 500) and today after I switched it on, desktop was bigger than screen. To be exact: screen resolution was set to the lowest possible and I could move mouse outside of screen (but only below - left, right and up worked normally, mouse could not exceed screen boundaries). I changed resolution back to normal, but the problem with desktop being bigger than screen remained (as before, only lower part - cannot see task bar, etc. When I hit windows button on keyboard, only upper part of menu start is visible). What I already tried was changing all kind of graphics and screen settings - none of them helped. I also tried to restore the system to few days before, but it didn't help neither. What can I do to make the desktop look "normally"? EDIT: Some additional info regarding screen: Sorry it's in polish - but let me explain. There are two screens I can choose (Monitor domyslny means default screen), but the second one (the default one) is not available. After I choose it and click apply number 1. is used (and as you can see it has only two resolutions available. There are more in the second one - but without 1024x600 though). The two ticked and grayed out options here are Use this screen as the main one and Enlarge Windows desktop to match this monitor's size. Too bad I cannot change them. When I choose the second screen, the first box is unchecked and grayed out. The second box is available to be changed but it doesn't matter anyway as after applying changes it reverts to the first screen anyway. EDIT: Intel Graphics Media Control Panel screenshot.

  Read the article

• PHP-FPM issue on LEMP Stack and WordPress

  - by jw60660

  I'm very much a NGINX and Server Admin beginner. I used this tutorial to install NGINX / PHP / mySQL / WordPress: C3M Digital Tutorial In this tutorial the backend php-cgi setup is configured using fastcgi. php5-fpm was installed during this tutorial: apt-get install nginx-full php5-fpm php5 php5-mysql php5-apc php5-mysql php5-xsl php5-xmlrpc php5-sqlite php5-snmp php5-curl After reading that the NGINX configuration on the WordPress codec was more secure than most tutorials, I decided to use the codex configuration: WordPress NGINX configuration in Codex The Codex configuration uses php-fpm for backend php-cgi. When opening the browser I got a 502 Bad Gateway error. The error log was: "2012/06/10 21:18:27 [crit] 14009#0: *4 connect() to unix:/tmp/php-fpm.sock failed (2: No such file or directory) while connecting to upstream, client: 12.3.456.789, server: mywebsite.com, request: "GET / HTTP/1.1", upstream: "fastcgi://unix:/tmp/php-fpm.sock:", hos t: "mywebsite.com"" In the main NGINX configuration file supplied by the codex I noticed the line starting "server unix:" in the upstream php block which point to the empty directory: # Upstream to abstract backend connection(s) for PHP. upstream php { server unix:/tmp/php-fpm.sock; # server 127.0.0.1:9000; } I checked the folder at /tmp and it was empty. Seems I missed configuring php-fpm to play with NGINX. Can someone point me in the right direction? Much appreciated!

  Read the article

• Recovering a damaged microSDHC

  - by djechelon

  I just bought from eBay a Kingston 32GB microSDHC that was advertised as defective. The seller said that there could be formatting problems or with transfer of large files. Unfortunately, when I got it, it was a total mess. My Nikon camera doesn't read it at all (OK, maybe it doesn't support 32GB) My Linux laptop doesn't mount it: can't read superblock The same laptop refuses to mkfs.msdos because it failed whilst writing reserved sector The same laptop, under Windows, doesn't read nor format the card HTC HD2 mounts the MMC, allows me to write via USB, but is unable to open the just written files OK, folks, now you would say I would have to go through Paypal complaint... that's not that easy. I consciously bought a half-price card that was known to show some defects, and Paypal complaints take time. Obviously, I can't accept somebody sold me a completely use-less computer decoration. So I'll keep it as last option. My question is Do you know a way, under either Linux or Windows, to thoroughly scan, test and possibly repair memory cards, even if I have to lose some percentage of space because of bad sectors? If I can keep at least half of the card intact it would certainly be fine. I used to do broken sector marking with hard disks in the past. I almost forgot: MONSTR:/home/djechelon # fsck /dev/mmcblk0p1 fsck from util-linux-ng 2.17.2 dosfsck 3.0.9, 31 Jan 2010, FAT32, LFN Read 512 bytes at 0:Input/output error

  Read the article

< Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >