Search Results

Search found 24646 results on 986 pages for 'linux vserver'.

Page 346/986 | < Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >

• Ubuntu Device-mapper seems to be invincible!

  - by Andrew Bolster

  I'm working on a hopefully unrelated question question and I've got to a strange situation. First: I know very little about the very low level hardware kernal storage driver magix, so I'm hoping a) someone can help and b) someone can explain it to me better. I've been trying a dozen different configurations of my 2x500GB SATA drives over the past few hours involving switching between ACHI/IDE/RAID in my bios; After each attempt I've reset the bios option, booted into a live CD, deleting partitions and rewriting partition tables left on the drives. Now, however, I've been sitting with a /dev/mapper/nvidia_XXXXXXX1 that seems to be impossible to kill! its the only 'partition' that i see in the Ubuntu install (but I can see the others in parted) but it is only the size of one of the drives, and I know I did not set any RAID levels other than RAID0. Anyone have any ideas how I can kill this and get back to just two independent IDE drives? Or can anyone convince me of a reason to go the AHCI route? Many thanks in advance.

  Read the article

• xorg DPMS off: keep VT from turning screen back on

  - by Metiu

  I have an embedded board with a small UPS. When AC power goes down, I need to turn off all power hungry devices in order to have a clean shutdown. First thing I do, is set DPMS to force powerdown, then go through the usual SIGTERM/SIGKILL/umount sequence. I have an Intel i915 Display adapter connected to an LVDS LCD panel. Unfortunately, when Xorg dies, Xserver or the VT code turn the LCD panel back on. I even tried working around it by directly poking the panel enable register in the Display chip, so that X doesn't know about it, but the panel goes back on when the VT comes back. Is there any "legal" way of keeping the display off? Thank you

  Read the article

• chown is not changing symbolic link

  - by rizidoro

  I'm trying to change the user/group of a symbolic link with the command: $ chown -h myuser:mygroup mysymbolic/ But it's not changing. I'm logged in as root. The current user/group is set to root:root. What went wrong?

  Read the article

• virtual disk image - file or partition

  - by tylerl

  I'm looking at the differences between using a file versus a partition to store a virtual disk image in VM use. The common knowledge is that partition-based images are faster than file-based images because of a decreased overhead. It makes sense, but I've never seen any actual numbers. My own testing bears out a different result. When I benchmark a direct-to-partition virtual disk, then format that same partition with ext4, create a virtual disk image stored on that ext4 filesystem, and then benchmark that, I see no speedup at all for the direct-to-partition virtual disk. Instead on some systems the file-based image is even faster (possibly due to host OS caching or something like that). This test was repeated many times on many systems, with fairly consistent results. So perhaps throwing out the performance justification, is it still considered better to use a partition rather than a virtual disk image? Is there some other reason why direct partition access is better than image files? Or perhaps is there some reason to go the other way around? Perhaps an advantage in one of the virtual disk file formats that you don't get with raw partition images?

  Read the article

• Open mysql only to localhost and a particular address

  - by Rodrigo Asensio

  My config: ubuntu server 9 and msyql 5 my.cnf = bind-address = 0.0.0.0 my iptables script = iptables -A INPUT -i eth0 -s 99.88.77.66 -p tcp --destination-port 3306 -j ACCEPT I can connect from any place to mysql, not only that IP. I made a iptables-save , /etc/init.d/netwokring restart... but I still can connect from any IP, any clue ?

  Read the article

• Why does the Java VM process eat up more RAM then specified in -Xmx parameter?

  - by evilpenguin

  I have multiple servers running CentOS 5.4 and only one application running on Java VM. I've configured the Java VM with the following arguments: java -Xmx4500M -server -XX:+UseConcMarkSweepGC -XX:+CMSIncrementalMode -XX:NewSize=1024m -Djava.net.preferIPv4Stack=true -Dcom.sun.management.jmxremote=true The machines I'm running the VM on has 6 GB RAM and no other applications running. After a while, the java process starts to hit the swap space really hard, I get this info out of the top command: 7658 root 25 0 11.7g 3.9g 4796 S 39.4 67.3 543:54.17 java On the other hand, if I connect via JConsole, it reports the Java VM has 2.6 GB used, 4.6 GB commited and 4.6 Gb max. java -version returns: java version "1.6.0_17" Java(TM) SE Runtime Environment (build 1.6.0_17-b04) Java HotSpot(TM) 64-Bit Server VM (build 14.3-b01, mixed mode) Why is the Java VM expanding so much past it's allocated heap size? And where does that memory go, if it's not reported in JConsole?

  Read the article

• virtualisation with kvm: export services from guest to the host

  - by ascobol

  Hello, I would like to export some services from the guest os to the host os, via kvm, and by the same way learn some things about networking. I have tried the following commands: In the host (kubuntu 10.4): $ sudo tunctl -u ascobol Set 'tap0' persistent and owned by uid 2401 $ sudo ifconfig tap0 192.168.2.1 netmask 255.255.255.0 broadcast 192.168.2.255 The ifconfig command returns: $ /sbin/ifconfig tap0 Link encap:Ethernet HWaddr 3e:4e:e3:cc:bc:92 inet addr:192.168.2.1 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::3c4e:e3ff:fecc:bc92/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:17 overruns:0 carrier:0 collisions:0 txqueuelen:500 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Then I run the virtual machine (ubuntu server 10.4): $ sudo kvm -hda ubuntuserver104.qcow2 -net nic -net tap,name=tap0,script=no (I'm using sudo because without it fails with the following message:) warning: could not configure /dev/net/tun: no virtual network emulation With sudo the virtual machine boots, I just get this message: pci_add_option_rom: failed to find romfile "pxe-rtl8139.bin" In the virtual machine: $ ifconfig eth0 192.168.2.2 netmask 255.255.255.0 broadcast 192.168.2.255 Now if I run: $ ssh 192.168.2.2 I just get a No route to host What is wrong with this setup ? Thanks !

  Read the article

• E: Internal Error, Could not perform immediate configuration (2) on libattr1 ? in Ubuntu

  - by user32178

  Hi, I am working with Ubuntu latest version. While installing via apt-get install i tried to abort that by pressing Ctrl+Z. It terminate successfully ;). But next time when i tried to use apt-get, i got some error "lock" and "temporally unavailable" something like that and **I unfortunately i delete the /var/lib/dkpg folder.** after that i cant install anything from apt-get, getting an error. E: Internal Error, Could not perform immediate configuration (2) on libattr1 so how can i solve this issue?

  Read the article

• E: Internal Error, Could not perform immediate configuration (2) on libattr1 ? in Ubuntu

  - by user6679

  Hi, I am working with Ubuntu latest version. While installing via apt-get install i tried to abort that by pressing Ctrl+Z. It terminate successfully ;). But next time when i tried to use apt-get, i got some error "lock" and "temporally unavailable" something like that and **I unfortunately i delete the /var/lib/dkpg folder.** after that i cant install anything from apt-get, getting an error. E: Internal Error, Could not perform immediate configuration (2) on libattr1 so how can i solve this issue?

  Read the article

• probems using ssh from cron

  - by Travis

  I am attempting to automate a script that executes commands on remote machines via ssh. I have public key authentication setup between the machines using ssh-agent. The script runs fine when executed from the command prompt. I suspect my problem is that cron isn't starting the ssh-agent due to it's minimalist environment. Here is the output when I add the -v flag to ssh: debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: gssapi-with-mic debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: Next authentication method: publickey debug1: Offering public key: /home/<user>/.ssh/id_rsa debug1: Server accepts key: pkalg ssh-rsa blen 149 debug1: PEM_read_PrivateKey failed debug1: read PEM private key done: type <unknown> debug1: Trying private key: /home/<user>/.ssh/id_dsa debug1: Next authentication method: password debug1: Authentications that can continue: publickey,gssapi-with-mic,password Permission denied, please try again. debug1: Authentications that can continue: publickey,gssapi-with-mic,password Permission denied, please try again. debug1: Authentications that can continue: publickey,gssapi-with-mic,password debug1: No more authentication methods to try. Permission denied (publickey,gssapi-with-mic,password). How can I make this work? Thanks!

  Read the article

• Server not sending a SYN/ACK packet in response to a SYN packet

  - by jeff

  Using iptraf, tcpdump and wireshark I can see a SYN packet coming in but only the ACK FLAG is set in reply packet. I'm running Debian 5 with kernel 2.6.36 I've turned off window_scaling and tcp_timestamps, tcp_tw_recycle and tcp_tw_reuse: cat /etc/sysctl.conf net.ipv4.tcp_tw_recycle = 0 net.ipv4.tcp_tw_reuse = 0 net.ipv4.tcp_window_scaling = 0 net.ipv4.tcp_timestamps = 0 I've attached an image of the wireshark output. http://imgur.com/pECG0.png Output to netstat netstat -natu | grep '72.23.130.104' tcp 0 0 97.107.134.212:18000 72.23.130.104:42905 SYN_RECV I've been doing everything possible to find a solution and have yet to figure out the problem, so any help/suggestions are much appreciated. UPDATE 1: I've set tcp_syncookies = 0 and noticed I am now replying with 1 SYN+ACK for every 50 SYN requests. The host trying to connect is sending a SYN request about once every second. PCAP FILE

  Read the article

• How To Perform Distributed Website Monitoring?

  - by cballou

  I would like to know how sites like the following perform distributed website monitoring (from multiple checkpoints/countries). pingdom.com, site24x7.com, uptrends.com, siteuptime.com, etc, etc. To be exact, what process would occur in checking if a given domain name went down? If the server finds that the site is down, what is the next step? Would it make a REST API request to a separate server to run the same test and report the results? I have a few theories, including: utilizing host(s) from different countries utilizing proxies from different countries I'm looking for the most proper or correct way to handle this, which can include the usage of servers from multiple countries/hosts.

  Read the article

• How can I fix puppet refusing to start and asking for "master.pp"?

  - by cwd

  I'm using the very latest version of puppet and have been following the Apress "Pro Puppet" guide step by step. I have installed puppet sudo aptitude install ruby libshadow-ruby1.8 sudo aptitude install puppet puppetmaster facter I have edited /etc/puppet/puppet.conf to include certname [master] certname=puppet.mydomain.com I have edited /etc/hosts and added the following line 127.0.0.1 puppet.mydomain.com puppet I have set the hostname of the server echo "puppet.mydomain.com" > /etc/hostname hostname -F /etc/hostname And then I try and run puppet from the command line. puppet master --verbose --no-daemonize And puppet gives me this error: Could not parse for environment production: Could not find file /master.pp I'm running all commands with sudo and the last line of the error message always says that it can't find master.pp and the path before it is to my current working directory. What am I doing wrong? I should also mention that I don't have a DNS record set up for puppet.mydomain.com - I saw some online documentation mentioning this might be a problem - however I was fairly sure that the hosts file would let me get around that.

  Read the article

• Why won't dhclient use the static IP I'm telling it to request?

  - by mike

  Here's my /etc/dhcp3/dhclient.conf: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, netbios-name-servers, netbios-scope, interface-mtu; timeout 60; reject 192.168.1.27; alias { interface "eth0"; fixed-address 192.168.1.222; } lease { interface "eth0"; fixed-address 192.168.1.222; option subnet-mask 255.255.255.0; option broadcast-address 255.255.255.255; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; } When I run "dhclient eth0", I get this: There is already a pid file /var/run/dhclient.pid with pid 6511 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:1c:25:97:82:20 Sending on LPF/eth0/00:1c:25:97:82:20 Sending on Socket/fallback DHCPREQUEST of 192.168.1.27 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.27 from 192.168.1.254 bound to 192.168.1.27 -- renewal in 1468 seconds. I used strace to make sure that dhclient really is reading that conf file. Why isn't it paying attention to my "reject 192.168.1.27" and "fixed-address 192.168.1.222" lines?

  Read the article

• Optimal file system type and mount options for an rsnapshot dedicated drive

  - by Nimmy Lebby

  We have an external USB 2 drive that we are using as a backup drive for our configuration. We use rsnapshot for the backups. It uses a few standard commands for managing snapshots: rm -rf: deletes expired snapshots mv: moves older snapshots down a slot cp -al: duplicates last snapshot to new slot rsync -a --delete --numeric-ids --relative: synchronizes new snapshot As you could see by the log below, the majority of the time is spent on the rm -rf and the cp -al steps: [25/Dec/2010:14:00:02] rsnapshot hourly: started [25/Dec/2010:14:00:02] echo 21012 > /var/run/rsnapshot.pid [25/Dec/2010:14:00:02] rm -rf /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.4/ /mnt/extdrive/snapshots/hourly.5/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.3/ /mnt/extdrive/snapshots/hourly.4/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.2/ /mnt/extdrive/snapshots/hourly.3/ [25/Dec/2010:14:15:48] mv /mnt/extdrive/snapshots/hourly.1/ /mnt/extdrive/snapshots/hourly.2/ [25/Dec/2010:14:15:48] cp -al /mnt/extdrive/snapshots/hourly.0 /mnt/extdrive/snapshots/hourly.1 [25/Dec/2010:14:23:32] rsync -a --delete --numeric-ids --relative /etc /mnt/extdrive/snapshots/hourly.0/sm4/ [25/Dec/2010:14:23:52] touch /mnt/extdrive/snapshots/hourly.0/ [25/Dec/2010:14:23:52] rm -f /var/run/rsnapshot.pid [25/Dec/2010:14:23:52] rsnapshot hourly: completed successfully My questions: I'm currently using ext4 for the filesystem. Maybe this is not the best choice from those available in Red Hat. Anyone have any recommendations that would speed up the process? The partition's mount options are sync,dirsync 1 2. Is there a way to optimize this since it's solely used for rsnapshot? Of course, reasoning would be greatly appreciated.

  Read the article

• File system concepts (df command)

  - by mkab

  I'm finding it difficult to understand some stuffs about the df command. Suppose I type df and I have the following output Filesystem 1k-blocks Used Avail Capacity Mounted on /dev/da0s1 some number some number number percentage /win /dev/da0s2 some number some number number percentage /win/home /dev/da0s3a some number some number number percentage / devfs some number some number number percentage /dev /dev/da0s3g some number some number number percentage /local /dev/da0s3h some number some number -number 102% /reste /dev/da0s3d some number some number number percentage /tmp /dev/da1s3f some number some number number percentage /usr /dev/da1s3e some number some number number percentage /var /dev/da1s1a some number some number number percentage /public Are the answers to the following questions correct? How many physical drives do I have? Ans: 2. da0s1 and da1s1 How many physical partitions on each disk? Ans: 8 for da0s1 and 1 for da1s1 How many BSD partition on each physical partition Ans: Impossible to determine. We have to use the -T to determine its type How is it possible for the file system /dev/da0s3h filled at 102%? And where is this overflowed data written?Ans: I have no idea for this one Thanks.

  Read the article

• How to change permission of my centos if I don't have the root password?

  - by Ali

  I've setup server on mac using virtualbox and my server is centos. but the guy who did it for me he forgot the root password that he setup at the beginning and what happen now is my website have a lot of problem due to the permission issues. So what can I do in order to retrive the password or even to change my permission without using root? The group for my website is apache and I believe I'm not in the same group.

  Read the article

• unable to run OpenOffice from text mode

  - by dilip

  I have installed OpenOffice in Redhat5 in text mode. When I tried to start OpenOffice using the command: sudo /usr/lib/openoffice/program/soffice "-accept=socket,host=localhost,port=8100; urp;StarOffice.ServiceManager " -nologo -headless -nofirststartwizard: " It shows the error saying javaldx: Could not find a Java Runtime Environment! So I installed jre in my system, and then I did not get any error but OpenOffice does not start. Also I checked the process regarding OpenOffice, but I haven's seen any process related to that. Can any one help me to fix this issue?

  Read the article

• LXC container can only access host via bridge

  - by vitaut

  I have an LXC container with i686 Ubuntu 12.04 running on a x86_64 Ubuntu 12.04 host. I've set up a bridge using instructions here. However the ping from the container only goes through to the host and not to other machines on the local network. Similarly only the host and not the other machines see the container OS. The host's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback iface eth0 inet manual auto br0 iface br0 inet dhcp bridge_ports eth0 bridge_fd 0 bridge_maxwait 0 The container's /etc/network/interfaces file looks as follows: auto lo iface lo inet loopback auto eth0 iface eth0 inet dhcp And here's the relevant part of the container's config: lxc.network.type=veth lxc.network.link=br0 lxc.network.flags=up Any ideas what I'm doing wrong? Additional info: The output of iptables-save on host: $ sudo iptables-save # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *filter :INPUT ACCEPT [6854:721708] :FORWARD ACCEPT [4067:538895] :OUTPUT ACCEPT [4967:522405] COMMIT # Completed on Sat Oct 26 06:06:48 2013 # Generated by iptables-save v1.4.12 on Sat Oct 26 06:06:48 2013 *nat :PREROUTING ACCEPT [82235:21547307] :INPUT ACCEPT [16:1070] :OUTPUT ACCEPT [9386:583359] :POSTROUTING ACCEPT [14693:1291952] -A POSTROUTING -s 10.0.3.0/24 ! -d 10.0.3.0/24 -j MASQUERADE COMMIT # Completed on Sat Oct 26 06:06:48 2013 The output of brctl show on host: $ brctl show bridge name bridge id STP enabled interfaces br0 8000.080027409684 no eth0 vethBkwWyV The output of ifconfig br0 on host: $ ifconfig br0 br0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet addr:192.168.1.11 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:232863 errors:0 dropped:0 overruns:0 frame:0 TX packets:59518 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:34437354 (34.4 MB) TX bytes:198492871 (198.4 MB) The output of ifconfig eth0 on host: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 08:00:27:40:96:84 inet6 addr: fe80::a00:27ff:fe40:9684/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:299419 errors:0 dropped:0 overruns:0 frame:0 TX packets:203569 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:59077446 (59.0 MB) TX bytes:372056540 (372.0 MB) The output of ifconfig eth0 on container: $ ifconfig eth0 eth0 Link encap:Ethernet HWaddr 00:16:3e:74:08:2b inet addr:192.168.1.12 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::216:3eff:fe74:82b/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:81 errors:0 dropped:0 overruns:0 frame:0 TX packets:113 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8506 (8.5 KB) TX bytes:9021 (9.0 KB)

  Read the article

• Help creating image from LVM

  - by jackhab

  I need to duplicate CentOS hard drive image for multiple stations. The HD has the following layout: Disk /dev/sdb: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 250GB 250GB primary lvm I saved /dev/sdb1 to file with fsarchiver but for sdb2 I get: /fsarchiver savefs an2.fsa /dev/sdb2 oper_save.c#1006,filesystem_mount_partition(): can't detect and mount filesystem of partition [/dev/sdb2], cannot continue. removed an2.fsa Although fsarchiver probe simple correctly detects sdb2 as LVM2_member. Is fsarchiver correct tool for this job? What's wrong? I'm on Ubuntu 9.1 with fsarchiver 0.6.8 and lvm tools installed. Thanks.

  Read the article

• Help creating image from LVM

  - by jackhab

  I need to duplicate CentOS hard drive image for multiple stations. The HD has the following layout: Disk /dev/sdb: 250GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 32.3kB 107MB 107MB primary ext3 boot 2 107MB 250GB 250GB primary lvm I saved /dev/sdb1 to file with fsarchiver but for sdb2 I get: /fsarchiver savefs an2.fsa /dev/sdb2 oper_save.c#1006,filesystem_mount_partition(): can't detect and mount filesystem of partition [/dev/sdb2], cannot continue. removed an2.fsa Although fsarchiver probe simple correctly detects sdb2 as LVM2_member. Is fsarchiver correct tool for this job? What's wrong? I'm on Ubuntu 9.1 with fsarchiver 0.6.8 and lvm tools installed. Thanks.

  Read the article

• OpenAFS on Fedora/CentOS

  - by Michael Pliskin

  I am trying to see if OpenAFS fits my needs as a distributed filesystem and is a bit stuck. There are docs but they're all quite hard to understand, so asking for some expert advice here. My questions: which version to install? I need windows client support so I need 1.5 - right? But it is not stable.. Or is it? And don't see any pre-built rpms for it, so compiling from sources? tried to compile and it worked but it created a non-"mp" kernel module while my kernel needs an mp one - how to workaround that? do I really need a new fresh partition to start with or I can re-use an existing one and just make it available via afp? any nice HOWTOs around?

  Read the article

• bash script with permanent ssh connection

  - by samuelf

  Hi, I use a bash script which runs /usr/bin/ssh -f -N -T -L8888:127.0.0.1:3306 [email protected] However, when I run the bash script, it waits.. I see the connection coming up but the script doesn't exit.. it's like it's waiting for the SSH process to finish, because when I manually kill it the bash script finishes as well. Any ideas how to resolve this? UPDATE: I have croned this script.. and the cron process is the one that becomes a zombie.. the actual scripts runs just fine, sorry about that, with ps -auxf I get: root 597 0.0 0.7 2372 912 ? Ss Jul12 0:00 cron root 2595 0.0 0.8 2552 1064 ? S 02:09 0:00 \_ CRON 1001 2597 0.0 0.0 0 0 ? Zs 02:09 0:00 \_ [sh] <defunct> 1001 2603 0.0 0.0 0 0 ? Z 02:09 0:00 \_ [cron] <defunct> and when I kill the ssh the defuncts disappear.. why would they become defunct?

  Read the article

• avoid check of list of known hosts

  - by shantanuo

  I get the following prompt everytime I try to connect a server using SSH. I type "yes", but is there a way to aovid this? The authenticity of host '111.222.333.444 (111.222.333.444)' can't be established. RSA key fingerprint is f3:cf:58:ae:71:0b:c8:04:6f:34:a3:b2:e4:1e:0c:8b. Are you sure you want to continue connecting (yes/no)?

  Read the article

• Can I recover a nano process from a previous terminal?

  - by davidparks21

  My system crashed while I was in a nano session with unsaved changes. When I log back in via SSH I see the nano process still running when I do a ps. davidparks21@devdb1:/opt/frugg_batch$ ps -ef | grep nano 1001 31714 29481 0 18:32 pts/0 00:00:00 nano frugg_batch_processing 1001 31905 31759 0 19:16 pts/1 00:00:00 grep --color=auto nano davidparks21@devdb1:/opt/frugg_batch$ Is there a way I can bring the nano process back under my control in the new terminal? Or any way to force it to save remotely (from my new terminal)?

  Read the article

< Previous Page | 342 343 344 345 346 347 348 349 350 351 352 353  | Next Page >