Search Results

Search found 10789 results on 432 pages for 'cpu upgrade'.

Page 347/432 | < Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >

• what can be causes of http server crash?

  - by mithunmo

  Hello , I am using WAMP server on Windows XP. Apache 2.2.11 MySQL 5.1.36 (INNODB engine) PHP 5.3.0 I observe that my WAMP server crashes in the following scenarios IF I use a Low end PC ( low processor speed and low RAM) After making some changes to httpd.conf file .For eg changing the Allow from IP address . But here it crashes only once and then it starts to work fine. Random crashes CRASH LOG szAppName : httpd.exe szAppVer : 2.2.11.0 szModName : php5ts.dll szModVer : 5.3.0.0 offset : 0000c309 C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\httpd.exe.mdmp C:\DOCUME~1\blrcom\LOCALS~1\Temp\WERc677.dir00\appcompat.txt My questions Does high CPU utilization/LOW RAM can also cause the HTTP server to crash ? excessive file reading as in every 10 seconds ? unlimited script execution time . I have set the maximum execution time in php script to 0 as my script has to execute for sometimes 2-3 days. Is there any way to avoid this ? Access to Database ? Should we use lock before reading and writing Can these be the reasons for random wamp server crashes ? OR is is some other programming error ? Please guide me . Regards, Mithun

  Read the article

• big speed difference on a network link with and without VPN tunnel

  - by xirtyllo

  Scenario: We have a network link between two offices. The link is provided by a third party company through a VLAN on their network, but to us it is totally transparent -as if we had a simple ethernet cable going from one location to the other-. We have one router at each side of the link, with 3 VPN tunnels in between the two. The test: When I test the speed of the network link with the routers in place, with one laptop directly connected to the router on each side, I consistently get ~30/35Mbps. But if I take out the routers and I test the link connecting the laptops directly to the ethernet cable at each side, I consistently get ~85/88Mbps. It's quite a big performance hit, and I would tend to think that the VPN tunnels are responsible for the slow down. Is it normal that this configuration (two routers with three VPN tunnels between them) takes away so much bandwidth? More info: The encryption algorithm used for the VPN tunnels is AES128. The routers model is Zyxel USG200 and Zyxel USG1000, and their CPU, memory, and storage use is well within normal limits. The nominal bandwidth of the network link is 100Mbps. The network link in question is supplied by a third party company (the building in between our two offices). Basically it passes through their network as a VLAN, but the VLAN is completely transparent to us (e.g. no configuration required on our side, just like one single cable from end to end). Unfortunately (or maybe fortunately) I cannot directly test different routers configurations as I'm not the person in charge of it.

  Read the article

• Problem recreating BCD on Windows 7 64bit - The requested system device cannot be found

  - by Domchi

  NVIDIA drivers upgrade crashed my Windows 7 installation, so I'm working to undo the damage. What I can do: I can boot Windows install from the USB drive, and I can boot the Hiren's Boot CD. Although automated Windows repair fails, I can get to command prompt when I boot Windows install from USB drive, and I can see my drive and all my data. What I cannot do: I cannot boot into Windows - I get this message: Windows failed to start. A recent hardwware or software change might be the cause. To fix the problem: 1.insert windos cd and run a repair your computer option. File: /boot/bcd Status: 0xc000000f Info: an error occured while attempting to read the boot configuration data. It seems that something is wrong with my /Boot/BCD, so I'm trying to recreate it from scratch. I've tried all the methods detailed here (including Windows repair which fails), and I'm left with the last one (near the bottom of that page). When I type the following command as in the tutorial: bcdedit.exe /import c:\boot\bcd.temp ...it fails with the following error: The store import operation has failed. The requested system device cannot be found. Many Google results say that I must use diskpart to set my partition active, however it's already set as active. Also, when I try this: bcdedit /enum It fails with similar message: The boot configuration data store could not be opened. The requested system device cannot be found. Does anyone know what does that error message mean, and what is the requested system device? I'd like to avoid having to reinstall Windows since all the files on disk seem to be fine.

  Read the article

• 16-bit MS-DOS Subsystem: csrss.exe

  - by Wesley

  Hi all, I just booted up my Samsung N120 netbook (with Windows XP Home SP3) and a dialog box came up with a command prompt window behind it. The dialog box is titled 16 bit MS-DOS Subsystem and the message is as follows: C:\DOCUME~1\SAMSUNG\csrss.exe The NTVDM CPU has encountered an illegal instruction. CS:0544 IP:0117 OP:63 00 64 00 34 Choose 'Close' to terminate the application. This only started on my most recent boot-up. One thing to note is that when I downloaded the Dropbox installer and opened it up, Panda Cloud Antivirus detected a suspicious file, which was csrss.exe and "neutralized it." However, an actual virus or trojan was not detected immediately before the file was detected and neutralized. Just under two weeks ago, a trojan and two viruses were detected for some odd reason. (I only went to website I knew and I do not torrent or browse adult sites.) Anyhow, the two viruses came up in temporary files and the trojan was "neutralized." Anyways, the main question is: How can I repair the csrss.exe file such that Windows XP starts up properly? A screenshot could be posted upon request. Thanks in advance!

  Read the article

• How to diagnose frequent segfaults

  - by Andreas Gohr

  My server is logging frequent segmentation faults to /var/log/kern.log in different tools. So far I've seen them in Perl, PHP and rsync. All installed software is up-to-date Debian packages. Here's an exerpt from the log file: Mar 2 01:07:54 gaz kernel: [ 5316.246303] imapsync[4533]: segfault at 8b ip 00007fb448c98fe6 sp 00007ffff571dd68 error 4 in libperl.so.5.10.1[7fb448bd7000+164000] Mar 2 01:17:42 gaz kernel: [ 5904.354307] php5-cgi[4441]: segfault at 2bb3dc8 ip 0000000002bb3dc8 sp 00007fffbeeaae48 error 15 Mar 2 02:54:05 gaz kernel: [11687.922316] php5-cgi[4495]: segfault at 2d7acf9 ip 0000000002d7acf9 sp 00007fff60c6eb18 error 15 Mar 2 10:50:08 gaz kernel: [40250.390322] BUG: unable to handle kernel paging request at 00000000024b03f0 Mar 2 10:50:08 gaz kernel: [40250.390341] IP: [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390353] PGD 208c71067 PUD 21c811067 PMD 209329067 PTE 8000000211c88067 Mar 2 10:50:08 gaz kernel: [40250.390365] Oops: 0011 [#1] SMP Mar 2 10:50:08 gaz kernel: [40250.390373] last sysfs file: /sys/devices/pci0000:00/0000:00:12.0/host4/target4:0:0/4:0:0:0/block/sdb/stat Mar 2 10:50:08 gaz kernel: [40250.390386] CPU 1 Mar 2 10:50:08 gaz kernel: [40250.390392] Modules linked in: cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_conservative xt_recent xt_tcpudp iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ ipv4 ip6table_filter ip6_tables xt_DSCP xt_TCPMSS ipt_LOG ipt_REJECT iptable_mangle iptable_filter xt_multiport xt_state xt_limit xt_conntrack nf_conntrack_ftp nf_conntrack ip_tables x_tables loop snd _hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm snd drm_kms_helper soundcore drm snd_page_alloc i2c_algo_bit shpchp i2c_piix4 edac_core pcspkr k8temp evdev edac_m ce_amd pci_hotplug i2c_core button ext3 jbd mbcache dm_mod powernow_k8 aacraid 3w_9xxx 3w_xxxx raid10 raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid1 raid0 md_mod sata_nv sata_sil sata_via sd_mod crc_t10dif ata_generic ahci pata_atiixp ohci_hcd libata r8169 mii thermal ehci_hcd processor thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan] Mar 2 10:50:08 gaz kernel: [40250.390566] Pid: 11482, comm: munin-limits Not tainted 2.6.32-5-amd64 #1 MS-7368 Mar 2 10:50:08 gaz kernel: [40250.390576] RIP: 0010:[<00000000024b03f0>] [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390586] RSP: 0018:ffff88021cc8dec0 EFLAGS: 00010286 Mar 2 10:50:08 gaz kernel: [40250.390593] RAX: 000000001ddc1000 RBX: 0000000000000010 RCX: ffffffff810f9904 Mar 2 10:50:08 gaz kernel: [40250.390600] RDX: 0000000000000000 RSI: ffffea0007688200 RDI: 0000000000000286 Mar 2 10:50:08 gaz kernel: [40250.390608] RBP: 00000000ffffffea R08: 0000000000000025 R09: 7865542f30312e35 Mar 2 10:50:08 gaz kernel: [40250.390615] R10: 000000d01cc8ddf8 R11: 0000000000000246 R12: ffff88021cc8def8 Mar 2 10:50:08 gaz kernel: [40250.390622] R13: 0000000002295010 R14: 00000000022c9db0 R15: 0000000002488d78 Mar 2 10:50:08 gaz kernel: [40250.390630] FS: 00007f3b3c8b2700(0000) GS:ffff880008d00000(0000) knlGS:0000000000000000 Mar 2 10:50:08 gaz kernel: [40250.390641] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 2 10:50:08 gaz kernel: [40250.390648] CR2: 00000000024b03f0 CR3: 000000021c5d1000 CR4: 00000000000006e0 Mar 2 10:50:08 gaz kernel: [40250.390656] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Mar 2 10:50:08 gaz kernel: [40250.390663] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Mar 2 10:50:08 gaz kernel: [40250.390671] Process munin-limits (pid: 11482, threadinfo ffff88021cc8c000, task ffff88021bf59530) Mar 2 10:50:08 gaz kernel: [40250.390681] Stack: Mar 2 10:50:08 gaz kernel: [40250.390687] ffffffff810f1d4a ffff880208c63228 0000000000000000 00007fffc2dcecc0 Mar 2 10:50:08 gaz kernel: [40250.390697] <0> 00000000024ba2b0 0000000002295010 ffffffff810f1e3d 0000000000000004 Mar 2 10:50:08 gaz kernel: [40250.390712] <0> ffff88021bf59530 ffff88021c4edc00 ffffffff812fe0b6 ffff88021c4edc60 Mar 2 10:50:08 gaz kernel: [40250.390732] Call Trace: Mar 2 10:50:08 gaz kernel: [40250.390742] [<ffffffff810f1d4a>] ? vfs_fstatat+0x2c/0x57 Mar 2 10:50:08 gaz kernel: [40250.390750] [<ffffffff810f1e3d>] ? sys_newstat+0x11/0x30 Mar 2 10:50:08 gaz kernel: [40250.390760] [<ffffffff812fe0b6>] ? do_page_fault+0x2e0/0x2fc Mar 2 10:50:08 gaz kernel: [40250.390768] [<ffffffff812fbf55>] ? page_fault+0x25/0x30 Mar 2 10:50:08 gaz kernel: [40250.390777] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b Mar 2 10:50:08 gaz kernel: [40250.390783] Code: Bad RIP value. Mar 2 10:50:08 gaz kernel: [40250.390791] RIP [<00000000024b03f0>] 0x24b03f0 Mar 2 10:50:08 gaz kernel: [40250.390799] RSP <ffff88021cc8dec0> Mar 2 10:50:08 gaz kernel: [40250.390805] CR2: 00000000024b03f0 Mar 2 10:50:08 gaz kernel: [40250.391051] ---[ end trace 1cc1473b539c7f6e ]--- Mar 2 11:42:20 gaz kernel: [43382.242301] php5-cgi[10963]: segfault at d81160 ip 0000000000d81160 sp 00007fff3adcb058 error 15 Mar 2 21:51:14 gaz kernel: [79916.418302] php5-cgi[20089]: segfault at 1c59dc8 ip 0000000001c59dc8 sp 00007fff9b877fb8 error 15 Mar 3 03:45:01 gaz kernel: [101143.334305] munin-update[22519] general protection ip:7f516dce204c sp:7fff6049a978 error:0 in libperl.so.5.10.1[7f516dc7d000+164000] Mar 3 11:22:37 gaz kernel: [128599.570307] php5-cgi[22888]: segfault at 36485a8 ip 00000000036485a8 sp 00007fff2d56e1c8 error 15 Mar 4 08:32:17 gaz kernel: [204779.842304] php5-cgi[22090]: segfault at 18 ip 0000000000689e5e sp 00007fff677a6a48 error 6 in php5-cgi[400000+6f9000] Mar 4 10:01:02 gaz kernel: [210104.434706] rsync[22236] general protection ip:7f14a07137f9 sp:7fff88f940b8 error:0 in libc-2.11.2.so[7f14a069d000+158000] Mar 4 11:32:22 gaz kernel: [215584.262316] BUG: unable to handle kernel paging request at 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.262331] IP: [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262343] PGD 0 Mar 4 11:32:22 gaz kernel: [215584.262350] Oops: 0010 [#2] SMP Mar 4 11:32:22 gaz kernel: [215584.262359] last sysfs file: /sys/devices/pci0000:00/0000:00:12.0/host4/target4:0:0/4:0:0:0/block/sdb/stat Mar 4 11:32:22 gaz kernel: [215584.262371] CPU 1 Mar 4 11:32:22 gaz kernel: [215584.262378] Modules linked in: cpufreq_userspace cpufreq_stats cpufreq_powersave cpufreq_conservative xt_recent xt_tcpudp iptable_nat nf_nat nf_conntrack_ipv4 nf_defrag_ipv4 ip6table_filter ip6_tables xt_DSCP xt_TCPMSS ipt_LOG ipt_REJECT iptable_mangle iptable_filter xt_multiport xt_state xt_limit xt_conntrack nf_conntrack_ftp nf_conntrack ip_tables x_tables loop snd_hda_codec_atihdmi snd_hda_intel snd_hda_codec snd_hwdep snd_pcm radeon snd_timer ttm snd drm_kms_helper soundcore drm snd_page_alloc i2c_algo_bit shpchp i2c_piix4 edac_core pcspkr k8temp evdev edac_mce_amd pci_hotplug i2c_core button ext3 jbd mbcache dm_mod powernow_k8 aacraid 3w_9xxx 3w_xxxx raid10 raid456 async_raid6_recov async_pq raid6_pq async_xor xor async_memcpy async_tx raid1 raid0 md_mod sata_nv sata_sil sata_via sd_mod crc_t10dif ata_generic ahci pata_atiixp ohci_hcd libata r8169 mii thermal ehci_hcd processor thermal_sys scsi_mod usbcore nls_base [last unloaded: scsi_wait_scan] Mar 4 11:32:22 gaz kernel: [215584.262552] Pid: 1960, comm: proxymap Tainted: G D 2.6.32-5-amd64 #1 MS-7368 Mar 4 11:32:22 gaz kernel: [215584.262563] RIP: 0010:[<00000000ffffff9c>] [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262573] RSP: 0018:ffff880209257e00 EFLAGS: 00010212 Mar 4 11:32:22 gaz kernel: [215584.262580] RAX: ffff8801514eb780 RBX: ffffffff810efb2d RCX: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262590] RDX: 0000000000000020 RSI: 0000000000000001 RDI: ffff8801514eb780 Mar 4 11:32:22 gaz kernel: [215584.262600] RBP: 00000000ffffffe9 R08: 0000000000000000 R09: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262611] R10: ffff880209257e78 R11: ffffffff81152c7c R12: 0000000000000001 Mar 4 11:32:22 gaz kernel: [215584.262622] R13: 0000000000008001 R14: 0000000000000024 R15: 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.262633] FS: 00007fca4de35700(0000) GS:ffff880008d00000(0000) knlGS:0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262644] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 Mar 4 11:32:22 gaz kernel: [215584.262650] CR2: 00000000ffffff9c CR3: 00000001c9cbb000 CR4: 00000000000006e0 Mar 4 11:32:22 gaz kernel: [215584.262661] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 Mar 4 11:32:22 gaz kernel: [215584.262671] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 Mar 4 11:32:22 gaz kernel: [215584.262682] Process proxymap (pid: 1960, threadinfo ffff880209256000, task ffff88021c4b1c40) Mar 4 11:32:22 gaz kernel: [215584.262693] Stack: Mar 4 11:32:22 gaz kernel: [215584.262698] ffffffff810f8566 ffff880209257e78 ffff88021c7bf000 ffff88021c7bf0c8 Mar 4 11:32:22 gaz kernel: [215584.262709] <0> 0000800000000000 ffff88021fc0f000 ffff880209257e78 00000000fffffffe Mar 4 11:32:22 gaz kernel: [215584.262724] <0> ffffffff810e5881 ffff880209257f48 0000000000000286 ffff88021fc0f000 Mar 4 11:32:22 gaz kernel: [215584.262743] Call Trace: Mar 4 11:32:22 gaz kernel: [215584.262753] [<ffffffff810f8566>] ? do_filp_open+0xa7/0x94b Mar 4 11:32:22 gaz kernel: [215584.262763] [<ffffffff810e5881>] ? virt_to_head_page+0x9/0x2a Mar 4 11:32:22 gaz kernel: [215584.262771] [<ffffffff810f9904>] ? user_path_at+0x52/0x79 Mar 4 11:32:22 gaz kernel: [215584.262779] [<ffffffff810cfec1>] ? get_unmapped_area+0xd7/0x139 Mar 4 11:32:22 gaz kernel: [215584.262787] [<ffffffff811019d5>] ? alloc_fd+0x67/0x10c Mar 4 11:32:22 gaz kernel: [215584.262795] [<ffffffff810eceaf>] ? do_sys_open+0x55/0xfc Mar 4 11:32:22 gaz kernel: [215584.262804] [<ffffffff81010b42>] ? system_call_fastpath+0x16/0x1b Mar 4 11:32:22 gaz kernel: [215584.262811] Code: Bad RIP value. Mar 4 11:32:22 gaz kernel: [215584.262819] RIP [<00000000ffffff9c>] 0xffffff9c Mar 4 11:32:22 gaz kernel: [215584.262828] RSP <ffff880209257e00> Mar 4 11:32:22 gaz kernel: [215584.262833] CR2: 00000000ffffff9c Mar 4 11:32:22 gaz kernel: [215584.263077] ---[ end trace 1cc1473b539c7f6f ]--- As you can see there are segfaults, a general protection fault and a Kernel Oops. My first guess was that there's a Hardware problem of some sort and I asked my Hoster (it's a rented root server) to do a full hardwarecheck - they did, but couldn't find any problem. I don't know what and how they checked but their support team is usually quite good. I ran memtester and cpuburn myself and couldn't find any error either. Unfortunately I have no reliable way to reproduce these segfaults, they seem to be more or less random. On a hunch I disabled the firewall of the system and ran one of the programs that segfaulted regularily (imapsync) and it seemed to take longer to segfault than before, so the problem might be related to the network stack. Or could just be a random thing. Here are the kernel specs: # uname -a Linux gaz 2.6.32-5-amd64 #1 SMP Wed Jan 12 03:40:32 UTC 2011 x86_64 GNU/Linux # cat /etc/debian_version 6.0 # lsmod Module Size Used by cpufreq_userspace 1992 0 cpufreq_stats 2659 0 cpufreq_powersave 902 0 cpufreq_conservative 5162 0 xt_recent 5977 0 xt_tcpudp 2319 0 iptable_nat 4299 0 nf_nat 13388 1 iptable_nat nf_conntrack_ipv4 9833 3 iptable_nat,nf_nat nf_defrag_ipv4 1139 1 nf_conntrack_ipv4 ip6table_filter 2384 0 ip6_tables 15075 1 ip6table_filter xt_DSCP 1995 0 xt_TCPMSS 2919 0 ipt_LOG 4518 0 ipt_REJECT 1953 0 iptable_mangle 2817 0 iptable_filter 2258 0 xt_multiport 2267 0 xt_state 1303 0 xt_limit 1782 0 xt_conntrack 2407 0 nf_conntrack_ftp 5537 0 nf_conntrack 46535 6 iptable_nat,nf_nat,nf_conntrack_ipv4,xt_state,xt_conntrack,nf_conntrack_ftp ip_tables 13899 3 iptable_nat,iptable_mangle,iptable_filter x_tables 12845 13 xt_recent,xt_tcpudp,iptable_nat,ip6_tables,xt_DSCP,xt_TCPMSS,ipt_LOG,ipt_REJECT,xt_multiport,xt_state,xt_limit,xt_conntrack,ip_tables loop 11799 0 radeon 573996 0 ttm 39986 1 radeon drm_kms_helper 20065 1 radeon snd_hda_codec_atihdmi 2251 1 drm 142359 3 radeon,ttm,drm_kms_helper snd_hda_intel 20019 0 i2c_algo_bit 4225 1 radeon pcspkr 1699 0 i2c_piix4 8328 0 snd_hda_codec 54244 2 snd_hda_codec_atihdmi,snd_hda_intel i2c_core 15712 5 radeon,drm_kms_helper,drm,i2c_algo_bit,i2c_piix4 snd_hwdep 5380 1 snd_hda_codec snd_pcm 60503 2 snd_hda_intel,snd_hda_codec snd_timer 15582 1 snd_pcm snd 46446 5 snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer soundcore 4598 1 snd evdev 7352 3 snd_page_alloc 6249 2 snd_hda_intel,snd_pcm k8temp 3283 0 edac_core 29261 0 edac_mce_amd 6433 0 shpchp 26264 0 pci_hotplug 21203 1 shpchp button 4650 0 ext3 106518 2 jbd 37085 1 ext3 mbcache 5050 1 ext3 dm_mod 53754 0 powernow_k8 10978 1 aacraid 59779 0 3w_9xxx 28684 0 3w_xxxx 20569 0 raid10 17809 0 raid456 44500 0 async_raid6_recov 5170 1 raid456 async_pq 3479 2 raid456,async_raid6_recov raid6_pq 77179 2 async_raid6_recov,async_pq async_xor 2478 3 raid456,async_raid6_recov,async_pq xor 4380 1 async_xor async_memcpy 1198 2 raid456,async_raid6_recov async_tx 1734 5 raid456,async_raid6_recov,async_pq,async_xor,async_memcpy raid1 18431 3 raid0 5517 0 md_mod 73824 7 raid10,raid456,raid1,raid0 sata_nv 19166 0 sata_sil 7412 0 sata_via 7928 0 sd_mod 29889 8 crc_t10dif 1276 1 sd_mod ata_generic 3047 0 ahci 32374 6 r8169 29229 0 mii 3210 1 r8169 thermal 11674 0 pata_atiixp 3489 0 libata 133632 6 sata_nv,sata_sil,sata_via,ata_generic,ahci,pata_atiixp ohci_hcd 19212 0 ehci_hcd 31151 0 processor 29935 1 powernow_k8 thermal_sys 11942 2 thermal,processor scsi_mod 122149 5 aacraid,3w_9xxx,3w_xxxx,sd_mod,libata usbcore 122034 3 ohci_hcd,ehci_hcd nls_base 6377 1 usbcore # free total used free shared buffers cached Mem: 8166128 1228036 6938092 0 140412 782060 -/+ buffers/cache: 305564 7860564 Swap: 2102456 0 2102456 So, basically my questions are: How can I diagnose this further? Is there any data in the log above that could help me to isolate the troublemaker? Are there any known problems with the above hardware/software I overlooked when googling for it? Is there a way to prevent the kernel from autoloading modules (I probably don't need all these modules and one of them might be the culprit)

  Read the article

• ATI radeon graphics card and screen freeze problem

  - by Thomas

  recently i upgrade my machine with new hardware component. my mother board is Gigabyte, processor Intel i3 3.6 ghz, ram 4 gb, graphics card ATI radeon 4350 1 GB. my OS installed is windows XP. when i am trying to play call of duty black ops then screen gets freeze and when i try to play other game like medal of honour then suddenly game closed suddenly after 15 or 20 minutes. i am not being able to find out the problem. whether i have problem in RAM or Graphics card. i asked few hardware person and one of them told me that i should installed windows 7 rather than windows xp. is it true. please help me to understand the problem and also tell me what should i do to fix this problem. please discuss in detail. thanks in advance. Update: yes i already install lates driver for ATI radeon 4350 but still the problem persist. do i need to install windows 7 instead of win xp because my processor is intel i3.

  Read the article

• Help building maya render node spec

  - by Ak

  Hi there, I'm looking to build 4x Maya render slaves/nodes for a friend of mine when his project gets green lit. The project involves MentalRay and lots of glass. I'm unsure if the new i7's 9xx or 8xx with hyper threading will do any better than a core 2 quad of the same (or close enough) speed. Does hyper threading make a difference to Maya or is it more performance per core based? I'm sure he's prefer I'd build another render node than pay for a bleeding edge CPU that only adds fractionly more GHz. -- The rest of the spec so far: 4Gb - 8Gb ram 64 bit OS: Probably Windows 7 (I know Linux is free, but want to build something my friend can support himself as easily as he supports his own workstation) 1TB HDD to hold textures, Maya files and renders which will be copied to central storage later Mobo with on-board video, gigabit NIC 500 - 650 watt PSU Desktop case something like a: Cooler Master ATCS 840 The machines will sold afterwards if necessary. -- If anyone has had experience in Maya and has done any tests with the new CPUs vs. the older ones I'd really appreciate your input.

  Read the article

• Nagios plug-in check_snmp receives NO SNMP data from a CISCO Router

  - by Shehryar

  I have tried setting up Nagios on Ubuntu 10.10, successfully installed and can login to web interface, I am however stuck on configuring snmp or I am doing something wrong here, i have followed various sites / nagios wiki to setup configuration (cfg) files. When I check on the web interface, it gives the following error on one of my cisco router: Current Status: UNKNOWN (for 0d 2h 55m 56s) Status Information: SNMP problem - No data received from host CMD: /usr/bin/snmpget -t 1 -r 5 -m RFC1213-MIB -v 1 [authpriv] 192.168.1.1:161 ifOperStatus.1 On the command-line itself, when I type the following, it just sits there waiting and waiting : sudo /usr/local/nagios/libexec/check_snmp -H 192.168.1.1 -C Routers -o sysUpTime.0 When I type the following command : I get an OK /usr/bin/snmpget -v1 192.168.1.1:161 1.3.6.1.2.1.1.5.0 -c "Routers" I have configured SNMP properly on our cisco device as we can collect SNMP Data via two other monitoring tool (SolarWinds and Manage Engine), we are tempted towards Nagios as its opensource. Will be grateful if someone could assist in rectifying this situation and guide me with setting up nagios to monitor Cisco Routers, Switches and a Few Servers. We want to monitor Bandwidth, cpu utilization, uptime and other necessary counters. Will be grateful for your assistance Thanks for reading Shehryar

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Server and Network Lag

  - by DanSpd

  At my home I have a server and my computer. Server has Windows Server 2008 Standart 64 bit installed and then my computer has Windows 7 64 bit installed. My home router is DIR-615 My server has a game server installed on it and basically total open connections on server are around 700. Once its around 700 server and then whole home network lags really badly. My internet connection is good and only around 600kb/s is being used out of 2mb/s (real download/upload speeds). So far I assume that my router has a connection limit and with server + my computer connections it peaks at around 1k and lags everything. Another assumption server lag comes from connection limit. On the internet I have read that standart version of server has connection limit of 700 + 10 reserved. I do not rmember where I found that information but it was on microsoft website. So I have two options. First is to upgrade my router to Netgear FVS318G-100 and second is to change connections limit on server. Any advices? Thank you

  Read the article

• Automatically check for Security Updates on CentOS or Scientific Linux?

  - by Stefan Lasiewski

  We have machines running RedHat-based distros such as CentOS or Scientific Linux. We want the systems to automatically notify us if there are any known vulnerabilities to the installed packages. FreeBSD does this with the ports-mgmt/portaudit port. RedHat provides yum-plugin-security, which can check for vulnerabilities by their Bugzilla ID, CVE ID or advisory ID. In addition, Fedora recently started to support yum-plugin-security. I believe this was added in Fedora 16. Scientific Linux 6 did not support yum-plugin-security as of late 2011. It does ship with /etc/cron.daily/yum-autoupdate, which updates RPMs daily. I don't think this handles Security Updates only, however. CentOS does not support yum-plugin-security. I monitor the CentOS and Scientific Linux mailinglists for updates, but this is tedious and I want something which can be automated. For those of us who maintain CentOS and SL systems, are there any tools which can: Automatically (Progamatically, via cron) inform us if there are known vulnerabilities with my current RPMs. Optionally, automatically install the minimum upgrade required to address a security vulnerability, which would probably be yum update-minimal --security on the commandline? I have considered using yum-plugin-changelog to print out the changelog for each package, and then parse the output for certain strings. Are there any tools which do this already?

  Read the article

• How to verify PostgreSQL 9 has installed correctly on a CentOS server?

  - by A4J

  I'm trying to install the PG (postgres) gem on a CentoOS server, but it keeps saying Postgres is too old, even though I have upgraded it to 9.1.3 (as per the instructions here http://www.davidghedini.com/pg/entry/install_postgresql_9_on_centos). I am using CentOS 5.8 (and Ruby 1.9.3) Here is the error message: Building native extensions. This could take a while... ERROR: Error installing pg: ERROR: Failed to build gem native extension. /usr/local/bin/ruby extconf.rb checking for pg_config... yes Using config values from /usr/bin/pg_config checking for libpq-fe.h... yes checking for libpq/libpq-fs.h... yes checking for pg_config_manual.h... yes checking for PQconnectdb() in -lpq... yes checking for PQconnectionUsedPassword()... no Your PostgreSQL is too old. Either install an older version of this gem or upgrade your database. *** extconf.rb failed *** Could not create Makefile due to some reason, probably lack of necessary libraries and/or headers. Check the mkmf.log file for more details. You may need configuration options. psql --version confirms my version: psql (PostgreSQL) 9.1.3 I can confirm packages installed: Setting up Install Process Package postgresql91-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-devel-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-server-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-libs-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Package postgresql91-contrib-9.1.3-1PGDG.rhel5.x86_64 already installed and latest version Nothing to do Any ideas on how to troubleshoot this? Thanks in advance.

  Read the article

• process and memory issue on linux server

  - by zapping

  Need some assistance in analyzing apache and php process running on linux server. Its a 8-core intel processor with 4GB ram. When the website on it runs the top displays like this. PID USER PR NI VIRT RES SHR S %CPU %MEM TIME+ COMMAND 23459 username1 16 0 151m 27m 8388 S 11.3 0.7 0:11.71 php5 23730 username1 16 0 151m 28m 8388 S 11.3 0.7 0:03.87 php5 23458 username1 16 0 151m 28m 8388 S 3.0 0.7 0:19.20 php5 16202 mysql 15 0 459m 38m 4624 S 0.7 1.0 62:33.81 mysqld 24141 nobody 15 0 311m 5832 2304 S 0.3 0.1 0:00.03 httpd Why does the command say php5 when the website is accessed. Both apache and php was preconfigured so not sure whats done there. Tried setting up the same site and db on a different server but on it the process shows httpd always and not php5. The site uses mysql db. The problem is server load seems to go till about 5.x when the website was access by about 16users. When the free -m command was given the output shows total used free shared buffers cached Mem: 3941 3727 213 0 236 2734 -/+ buffers/cache: 756 3184 Swap: 4095 0 4095 Lots of memory seems to be in cache and free memory is less. Even when the website is not accessed that is leaving it very much idle for about 2days the free memory showed just 190. When the site is accessed the free memory seems to be go till 90mb then it increases to about 150mb. It always seems to remain just about 200mb. Is it somehow related to the server load showing 5.x. Will adding some more RAM resolve the load issue?

  Read the article

• fail2ban Error Gentoo

  - by Mark Davidson

  Hi All I've recently setup a new VPS running Gentoo (My first time using the distro so please forgive me is this is a really easy one) and as I've done with other servers installed fail2ban. Setting it up to block the host via iptables, on too many unsuccessful logins with ssh. However I'm getting a strange error that I can't quite solve. When I start fail2ban I get these lines in the error log 2009-11-13 18:02:01,290 fail2ban.jail : INFO Jail 'ssh-iptables' started 2009-11-13 18:02:01,480 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 If I try and force a ban these errors show up in the log and the host is not banned 2009-11-13 11:23:26,905 fail2ban.actions: WARNING [ssh-iptables] Ban XXX.XXX.XXX.XXX 2009-11-13 11:23:26,929 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:26,930 fail2ban.actions.action: ERROR Invariant check failed. Trying to restore a sane environment 2009-11-13 11:23:27,007 fail2ban.actions.action: ERROR iptables -N fail2ban-SSH iptables -A fail2ban-SSH -j RETURN iptables -I INPUT -p tcp --dport ssh -j fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: ERROR iptables -n -L INPUT | grep -q fail2ban-SSH returned 100 2009-11-13 11:23:27,016 fail2ban.actions.action: CRITICAL Unable to restore environment My versions are as follows Linux masked 2.6.18-xen-r12 #2 SMP Wed Mar 4 11:45:03 GMT 2009 x86_64 Intel(R) Xeon(R) CPU E5504 @ 2.00GHz GenuineIntel GNU/Linux net-analyzer/fail2ban-0.8.4 net-firewall/iptables-1.4.3.2 If anyone could shead some light on these errors that would be great, I did wonder if it was a problem with iptables or some kernel modules but I can block an IP if I do. iptables -I INPUT -s 25.55.55.55 -j DROP so makes me think its something a bit more unusual. Thanks a lot in advance

  Read the article

• Can reprepro accept a new version of a package into the repository?

  - by kai

  I have installed a package into my own debian package repository like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.8-0_all.deb my-package_0.8-0_all.deb: component guessed as 'main' Exporting indices... I have installed my package on a few machines using apt-get install. I have now added new features to my software and would like to add a new minor version of my package to the repository so that I may update my machines using apt-get upgrade. I try to do this like so: $ sudo reprepro -b /var/packages/ubuntu includedeb maverick my-package_0.9-0_all.deb my-package_0.9-0_all.deb: component guessed as 'main' Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|i386', as it has already '1.0-0'. Skipping inclusion of 'my-package' '1.0-0' in 'maverick|main|amd64', as it has already '1.0-0'. It looks like I need to tell reprepro that this is a new version of the same package but I have no idea how to do this. I have read the reprepro man page several times and searched on the net for a couple of hours but I have not found any answers. Am I missing something? Many thanks.

  Read the article

• Improving Performance of RDP Over LAN

  - by Jared Brown

  Architecture: A deployment of 6 new HP thin clients (Windows XP Embedded) with TCP/IP access to several new HP servers (Windows 2003 Server). Each thin client is connected over fiber optic to a Gigabit Cisco switch, which the servers are connected to. There are 10/100 Ethernet to fiber converter boxes on each end of the fiber cables. Problem: Noticeable lag over RDP while using the Unigraphics CAD package. 3D models take .5 to 1 second to respond to mouse actions. Other Details: Network throughput on each thin client's RDP session is 7288 kbps. RDP connection settings - color setting: 15k, all themes, etc. turned off. Local and remote system performance stats are well within norms (CPU, Memory, and Network). Question: Are there newer versions of terminal services or RDP I can use on my existing OSes? Are there compression algorithms, etc. that are well suited for a high-bandwidth LAN? Are there valid alternatives that will yield higher performance (i.e. UltraVNC with drivers installed)? Are there TCP/IP tuning options I can exploit?

  Read the article

• MySQL socket connections working, but not port connections

  - by Neil

  I installed MySQL community 5.1.45 on my Snow Leopard 10.6, using the pkg from their site. I had previously installed a MySQL binary from entropy.ch. In the previous installation, the connections were working fine before I upgrade to Snow Leopard. In Snow Leopard, both the installations are problematic. Using an app called Sequel Pro, if I connect with the socket operation, it connects properly. However, a standard connection with the same credentials doesn't work. From what I've understood, socket connections happen on the machine itself between processes, whereas normal connections occur over the network/ports, in this case a loopback to my machine, since the server and client are both on the same machine. My new CakePHP installation isn't being able to connect to the db with the root credentials I provided. Btw, I've been starting the MySQL server using the Preference Pane. When I tried running mysqld from terminal, it gave me: 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test 100323 1:54:37 [Warning] Can't create test file /usr/local/mysql-5.1.45-osx10.6-x86_64/data/mbp.lower-test mysqld: Can't change dir to '/usr/local/mysql-5.1.45-osx10.6-x86_64/data/' (Errcode: 13) 100323 1:54:37 [ERROR] Aborting 100323 1:54:37 [Note] mysqld: Shutdown complete mbp is the name of my machine. How do I fix this so that my webserver can connect to the mysql server?

  Read the article

• ZFS - destroying deduplicated zvol or data set stalls the server. How to recover?

  - by ewwhite

  I'm using Nexentastor on a secondary storage server running on an HP ProLiant DL180 G6 with 12 Midline (7200 RPM) SAS drives. The system has an E5620 CPU and 8GB RAM. There is no ZIL or L2ARC device. Last week, I created a 750GB sparse zvol with dedup and compression enabled to share via iSCSI to a VMWare ESX host. I then created a Windows 2008 file server image and copied ~300GB of user data to the VM. Once happy with the system, I moved the virtual machine to an NFS store on the same pool. Once up and running with my VMs on the NFS datastore, I decided to remove the original 750GB zvol. Doing so stalled the system. Access to the Nexenta web interface and NMC halted. I was eventually able to get to a raw shell. Most OS operations were fine, but the system was hanging on the zfs destroy -r vol1/filesystem command. Ugly. I found the following two OpenSolaris bugzilla entries and now understand that the machine will be bricked for an unknown period of time. It's been 14 hours, so I need a plan to be able to regain access to the server. http://bugs.opensolaris.org/bugdatabase/view_bug.do?bug_id=6924390 and http://bugs.opensolaris.org/bugdatabase/view_bug.do;jsessionid=593704962bcbe0743d82aa339988?bug_id=6924824 In the future, I'll probably take the advice given in one of the buzilla workarounds: Workaround Do not use dedupe, and do not attempt to destroy zvols that had dedupe enabled. Update: I had to force the system to power off. Upon reboot, the system stalls at Importing zfs filesystems. It's been that way for 2 hours now.

  Read the article

• Looking for updated BIOS for '99 Gateway in order to format/recognize >127 GB HD

  - by Jeff

  I have a '99 Gateway that's apparently too old for even Gateway to acknowledge it exists. Want to use it as a media hub and put in a 320GB HD, but it will not format above 127GB even running Win XP SP3. Read somewhere that upgrading the BIOS may do the trick, but I can't find the correct BIOS, and GW has been no help. Hoping I can just upgrade the BIOS, which is 11 years old. Any help would be much appreciated! I don't know where to look, and searches have been fruitless. System info: OS Name Microsoft Windows XP Home Edition Version 5.1.2600 Service Pack 3 Build 2600 OS Manufacturer Microsoft Corporation System Name xxxx System Manufacturer Gateway System Model TABOR_II System Type X86-based PC Processor x86 Family 6 Model 7 Stepping 3 GenuineIntel ~596 Mhz BIOS Version/Date Intel Corp. 4W4SB0X0.15A.0015.P10, 9/28/1999 SMBIOS Version 2.1 BIOS info (from a free app I located): BIOS Type: Phoenix BIOS Date: September 28th 1999 BIOS ID: 4W4SB0X0.15A.0015.P10.9909281445-None BIOS OEM: 4W4SB0X0.15A.0015.P10 Chipset: Intel 440BX/ZX rev 3 SuperIO: SMC 70x or 80x rev 0 at port 0370 Manufacturer: Gateway Motherboard: WS440BX

  Read the article

• TicTac Photo and Windows 7

  - by Ben

  Hello, My wife has been creating a tictac photo album. I had to upgrade to windows 7 as i had enough of Vista so i backed up the tic tac photo file and the photos to an external hard disk and performed a fresh install of win7. Now here is the problem. TicTacPhoto says it can find the photos in the album. The locations were as follows: Vista: C:\Users\Kelly\Pictures Win 7 C:\Users\Kelly\My Pictures When i try to create a Pictures folder under Kelly it popups a message about merging the two folders and simply moves the pictures to the My Pictures folder. Does anyone know a way to make a foler called pictures so i can eliminate the file path problem and then try again with tic tac photo support to get them to fix my file. My wife is going to kill me as its our wedding album and she has spent upwards of 30hrs designing it and me upgrading to win 7 means its all my fault. She does not understand file paths etc. Im going to try and open the album file in a text editor and see if i can see anything but thought i would ask here as well. Any help appreciated.

  Read the article

• ATI gpu (video accel, decode, encode, ATI Stream, DXVA)

  - by Shiki

  Okay its a long question title for sure. I'm looking for a new video card (yes,SU is not a page for that, but wait). I've been a loyal NVidia customer ever since, now using a 8600gts. Old but still somewhat good, its a bit slow though. I want an upgrade because 8600gts wont support better vdpau and new features. I checked out the prices and the documents, I would need a GTX260 card. Which costs ..well.. a lot. ATI performs much better for that price. (At least on every test it outperforms GTX260). However, as far as I know there is no gpu accel with ATI. The things you can use is DXVA only, no other method. Could you correct me out there? Will be there a gpu accel for ATI also? Or is there one available? (DXVA is not bad, but kinda slow compared to NVIdia's CUDA.) What about openCL? How does ATI support that? (I'm talking about the 5850 ATI card at the minute, I would buy that instead of the NVidia.)

  Read the article

• Python easy_install confused on Mac OS X

  - by slf

  environment info: $ echo $PATH /opt/local/bin:/opt/local/sbin:/sw/bin:/sw/sbin:/usr/bin:/bin:/usr/sbin:/sbin:/usr/local/bin:/usr/X11/bin:/usr/X11R6/bin:/opt/local/bin:/Developer/Platforms/iPhoneOS.platform/Developer/usr/bin:~/.utility_scripts $ which easy_install /usr/bin/easy_install specifically, let's try the simplejson module (I know it's the same thing as import json in 2.6, but that isn't the point) $ sudo easy_install simplejson Searching for simplejson Reading http://pypi.python.org/simple/simplejson/ Reading http://undefined.org/python/#simplejson Best match: simplejson 2.1.0 Downloading http://pypi.python.org/packages/source/s/simplejson/simplejson-2.1.0.tar.gz#md5=3ea565fd1216462162c6929b264cf365 Processing simplejson-2.1.0.tar.gz Running simplejson-2.1.0/setup.py -q bdist_egg --dist-dir /tmp/easy_install-Ojv_yS/simplejson-2.1.0/egg-dist-tmp-AypFWa The required version of setuptools (>=0.6c11) is not available, and can't be installed while this script is running. Please install a more recent version first, using 'easy_install -U setuptools'. (Currently using setuptools 0.6c9 (/System/Library/Frameworks/Python.framework/Versions/2.6/Extras/lib/python)) error: Setup script exited with 2 ok, so I'll update setuptools... $ sudo easy_install -U setuptools Searching for setuptools Reading http://pypi.python.org/simple/setuptools/ Best match: setuptools 0.6c11 Processing setuptools-0.6c11-py2.6.egg setuptools 0.6c11 is already the active version in easy-install.pth Installing easy_install script to /usr/local/bin Installing easy_install-2.6 script to /usr/local/bin Using /Library/Python/2.6/site-packages/setuptools-0.6c11-py2.6.egg Processing dependencies for setuptools Finished processing dependencies for setuptools I'm not going to speculate, but this could have been caused by any number of environment changes like the Leopard - Snow Leopard upgrade, MacPorts or Fink updates, or multiple Google App Engine updates.

  Read the article

• Poor NFS Performance: OpenFiler

  - by Safin09

  Good Day Everyone, I have an issue with OpenFiler, a Linux-based operating that converts a computer system into a SAN/NAS appliance. Here is the problem. In my environment we have two Netapp Storevault 500 appliances that I normally perform backups to a NFS share. There are two backup cronjobs that use ghettoVCB to backup two groups of VM's. One group is a pool of 3 VMs. This takes 13 mins to complete. A second job that backups a pool of 5 VMs to a 2nd Storevault appliance which takes 2 hours. We then installed Openfiler on a old server that has 2 core Xeon processors. There is a software RAID 5 process in place. When performing the same backups to a NFS Openfiler share, the first backup job, which takes 13 mins, takes around 4 hours. The second backup job, which takes 2 hours, takes almost 10 hours to complete. This is unacceptable!!!! Especially considering the strain placed on the host ESX Server. I assumed that because of the software RAID 5, the overhead on the CPU explained the long backup times. I then installed Openfiler on a 2nd server, an IBM x306 machine which has a P4 Intel processor. This time no software RAID or any RAID at all. A single 750GB hard drive that contained the OS and the rest of the disk uses to backup VMs to a NFS share. I performed the first backup job of the pool of 3 VMs. This time the backup job took 1 and 1/2 hours to complete instead of 13 mins!!!!!!!!!! Is Openfiler simply poor at being an NFS Server!!!!!!!!!!!!! Has anyone else had these issues with Openfiler?

  Read the article

• Running mod_php and suPHP same time

  - by BHare

  I recently went from Debian Lenny with 5.2.x and was able to use mod_php for any php files that were not located in /home/ and suPHP for all the php files that were located in /home/. I did this because I needed a default php.ini (given me all features of php) for my websites in /var/www/ and I didn't want to have to change the owner of all the .php files from root. I also had a default php.ini for all the /home/ php files without dangerous features. This was I had setup: <IfModule mod_suphp.c> <Directory /home/> AddType application/x-httpd-php .php .php3 .php4 .php5 suPHP_AddHandler application/x-httpd-php suPHP_Engine on suPHP_ConfigPath /home/shared/ </Directory> </IfModule> This was working perfect, but recently I upgraded to PHP to 5.3.5 from dotdeb (Lenny has no official php 5.3) . This had weird issues on lenny such as not display errors correctly and little tid bits. So I decided to upgrade from lenny to squeeze. Uninstalled php (along with it came suphp) and reinstalled with the new source. I now have 5.3.3-7 with Debian Squeeze but I cannot get mod_php and suPHP to run at the same time anymore. mod_php will always work and there are no errors in apache2 or suphp logs. If I disabled mod_php then suPHP will work. Is there thing I am doing wrong?

  Read the article

< Previous Page | 343 344 345 346 347 348 349 350 351 352 353 354  | Next Page >