Search Results

Search found 15661 results on 627 pages for 'protected mode'.

Page 349/627 | < Previous Page | 345 346 347 348 349 350 351 352 353 354 355 356  | Next Page >

• "Request not supported" in IPCONFIG (WinXP SP3)

  - by pablog

  In a customer PC (Windows XP SP3), suddenly the network went down: the network adapter appears with an error mark. I replaced the network card, but the new one does the same thing. When I enter IPCONFIG, XP shows this error (in standard and safe mode): Internal error occurred Request not supported Unable to query host name If I start the system with a boot cd the PC runs fine, so the problem seems to be in the XP installation. I tried: uninstalling and reinstalling the network card in the Device Manager disabling and reenabling the card netsh int ip reset netsh winsock reset catalog and a couple of "reset" programs (WinsockxpFix.exe, etc) with no luck. Is there any way to fix it without reinstalling XP? TIA, Pablo

  Read the article

• 802.11 Capture Frame

  - by ALi

  I am using wireshark in monitor mode to capture all the frame. I buffered all the QosData in order to calculate the biterate of each station on the network. I calculate the biterate but it is not an accurate value. what i need to know is when the station use the network alone and when it uses it with another station? i know if two station with different wifi card for exemple ( st1 802.11g 54 Mb/s, st2 802.11n 300 Mb/s) if st1 uses alone the line the biterate used is 28 MB/s and if st2 uses alone the network the bit rate increase to approximately 150Mb/s but if the two station use the network at the same time the st1 lost about 80% of its bit rate because of the st1 wifi card thx in advance

  Read the article

• Is span monitoring on Cisco ASA 5520 possible?

  - by Brent

  From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

  Read the article

• Carbonite Restore Error after Windows Update

  - by Rev

  I recently installed Windows 8 on my main machine, and I'm have an issue with Carbonite. I can't restore any files from my previous OS, only files that where backed up from the current OS. I can download them from the web service, but I can't restore them with the client. The error says "You don't have the necessary security permissions to restore this file." (The file on top was backed up from the new install, while the one on bottom was from the old install.) I'm also having another issue, where Carbonite doesn't think it's running in admin mode. I think it's probably related to this error. When I right click to restore a file, I can't choose a location to restore to. I contacted Carbonite, and they said it's a known issue that apparently happens when upgrade from XP to 7, but they wouldn't help me since I'm running a beta OS. Hopefully one of you fine folks will have an idea.

  Read the article

• VPN and Bonjour conflicting

  - by JW.

  Does anyone know why a VPN connection might interfere with Apple's Bonjour? I've noticed that my Mac and various iDevices have trouble finding each other on my local network, when I have VPN connections open. Things like Home Sharing and Wi-Fi Sync work some of the time, but sometimes fail to find the other device. The VPN connections are made using IPSecuritas, which is a GUI around raccoon. I have the local "endpoint mode" set to Host. Apple mentions that Home Sharing may conflict with VPNs, but they don't specify why, or how to fix it. I'm using a Mac with OS 10.7.3 and IPSecuritas to connect to the VPN, an iPhone, and an iPad.

  Read the article

• idle proccesses and high memory bad? uwsgi/django

  - by JimJimThe3rd

  I have a VPS with 256MB of ram. I'm running nginx, uwsgi and postgresql on Ubuntu 12.04 for a soon to be Django site. About 200MB of ram are being used despite the website not being active, the uwsgi processes seem to just be idling. Is this bad? I once heard that having a bunch of free memory isn't necessarily a good metric because it is possible that the memory in use can easily be freed up. I mean, it is possible that the server is storing commonly used "stuff" in case it is accessed but is more than happy to dump it if the ram is needed. But I'm really not sure, hence me asking this question. If it is bad I could set some of the application loading options for uwsgi like "cheap" or "idle" mode. Screenshot of my htop

  Read the article

• 1000 HZ linux kernel necessary if I have tickless and high resolution timer?

  - by Bob

  I am trying to improve performance on my server. I have a few processes that need low jitter (less than 10ms variance). I have a load average of 4 maximum on an i7-920 (4 physical cores, 8 with HT). There are about 10 processes ranging from 40% to 90% of a core user mode. System usage is 3% total. Total CPU usage is 80% max. Will setting the kernel from 100hz to 1000hz improve the jitter if tickless and high resolution timers are already set? This page seems to indicate it still does something. https://lkml.org/lkml/2009/4/28/401 How about changing from voluntary (PREEMPT_VOLUNTARY) to preemptible (PREEMPT)?

  Read the article

• How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

  - by user60813

  Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

  Read the article

• TIME column in TOP command for mysql

  - by michael

  When I run top on my database server I get that mysqld has been running for 4:00.51 and it continues to go up. I assume this means that one process with mysql has been running this long from other posts on here. Its not set to cumulative mode as best I can tell as the heading looks like it would change to CTIME if that be the case. What I'm wondering is if this is normal for a site that makes a lot of individual connections using PHP. I shouldn't have any long running processes that would hold on to a mysql connection for this long, only seconds at most. Am I incorrect to assume that this time relates to one connection/process running? I think usually I see it flash up and away on the TOP, not just stay there with this number increasing.

  Read the article

• Hybrid drive not booting faster than a normal HD

  - by Nigel Trotter

  I have used Windows 7 to create an image of my existing standard 160GB HD and copied this image back to a bigger 500GB Seagate hybrid drive. After copying the image to the hybrid I had to resize the partition, which was fine but after rebooting a few times to "teach" the hybrid, I have no increase in boot speed. It still takes 20-25 seconds to close down and then over a minute to start up. Is this something to do with the way the image lays itself on the drive indiscriminately? Do I need to load the OS on the drive from scratch to get the benefits? My PC with an i5 processor, is using AHCI mode.

  Read the article

• Where is the encfs volume key stored?

  - by Waldorf

  I am trying to use encfs in reverse mode. I understand that the passphase is used to encrypt a key which is then stored encrypted into the encfs6.xml file. What I do not understand is the following. Create en encrypted virtual fs of a folder by using passphrase A unmount this folder. Delete all contents including the encfs6.xml file If you then try to do the same with another passphrse I would expect that a new encfs6.xml would be created. However I get the following error message: "Error decoding volume key, password incorrect" So I wonder, what volume key is incorrect, I thought it was in the encfs6.xml file ?

  Read the article

• Is there a way to see what is typed or websites visted when a spouse is using google chrome in incognito ?

  - by Ken

  My spouse and I have 2 laptops both running windows 7 and I have 1 desktop running vista. I have reason to believe she is cheating and I want to watch her internet usage, She is always using google chrome in incognito mode. I have tried a few keyloggers but they never seem to be able to get the keystrokes when she is on google. I dont know if there is a way I can network them so they go thru my desktop then to the internet. We are using Brighthouse cable internet. any ideas would be great thank you

  Read the article

• Sysprep on Windows 7 for a non-windows admin?

  - by askvictor

  I'm needing to use sysprep to deploy some Windows 7 machines. I can't find any resources that explain this very easily. In particular, I've loaded all of the programs I want for the image onto a computer. If I want to use prepares this for cloning onto 200 other machines, what steps would I need to take? Or do I need to start again, creating the image using 'audit' mode? The machines I'm using come pre-configured from the manufacturer with a host of custom drivers that wouldn't be fun to re-install - I'd rather use their base image to build upon. Cheers, Victor

  Read the article

• fast opening and closing connection with a specific port

  - by michale

  We have a Main application named "Trevor" installed in 2008R2 machine named "TEAMER12" which is slow now. One more application named "TVS" also running in and found there were many connections per second occurring to port 5009. netstat tool mentions that some fast connection open/close seen for port 5009 So first it will be listening mode like shown below TCP 0.0.0.0:5009 TEAMER12:0 LISTENING then establishes connection like TCP 127.0.0.1:5009 TEAMER12:49519 ESTABLISHED TCP 127.0.0.1:5009 TEAMER12:60903 ESTABLISHED After that iwill become TIME_WAIT and i could see several entries like shown below TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT after that it will establish connection like TCP 127.0.0.1:60903 TEAMER12:5009 ESTABLISHED TCP 127.0.0.1:64181 TEAMER12:microsoft-ds ESTABLISHED again it will go several entries like TIME_WAIT TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT Finally it will establish like this TCP 172.26.127.40:139 TEAMER12:0 LISTENING TCP 172.26.127.42:139 TEAMER12:0 LISTENING TCP 172.26.127.42:5009 TEAMER12:64445 ESTABLISHED TCP 172.26.127.42:64445 TEAMER12:5009 ESTABLISHED Can any body tell me whats the reason behind why many connections per second occurring to port 5009 and why application slow?

  Read the article

• Redhat cluster Vs Pacemaker Vs Gluster Vs Sheepdog

  - by chandank

  Changing the entire question as earlier one was very confusing. I have been exploring different clustering system to run Virtual machines on two different machines on LAN with high availability. Currently I am already using DRBD resource on two different machines on Primary/Secondary mode. In case the primary fails I manually promote the secondary to Primary and start the VM. I also explored Gluster and looks good, however, I would rather prefer clustering over Gluster (user space FS). So if anyone has idea which one would be better from ease of use prospective please I would be interested in. Moreover, sheepdog project appears good, however, could not find much documentations/Howtos. I am using Centos 6.

  Read the article

• Multi-monitor setup: one widescreen monitor, one regular (4:3) monitor; is this usually possible?

  - by stakx

  I'm trying to find out whether it's generally possible to have a multi-monitor setup with both a widescreen monitor and a regular monitor (ie. one with a 4:3 picture ratio). I'd like to run them in Extended Desktop mode on a Windows Vista machine. The computer is a Dell notebook with an onboard Intel GMA 4500MHD graphics chipset. While I know that this notebook is capable of driving multiple monitors, I don't know if it is also able to drive monitors with varying resolutions. Does anyone know if differing screen resolutions is generally a problem?

  Read the article

• Rotate monitor to portrait on Windows Server 2003 with ATI card

  - by user10179

  Does anyone know if it is possible to rotate a monitor from landscape to portrait mode on Windows Server 2003 32-bit with an ATI video card? According to Dell's site, I should be able to rotate my Dell P2310H monitor by installing drivers from their website, but they don't have drivers for Windows Server 2003. I let Windows Update search for the driver (with the driver CD that came with the monitor in my drive) and it did install drivers, but I still don't see any options for rotating. Some people say that the ATI Catalyst Control Center allows for monitor rotation, but I've never been able to run that software on Windows Server 2003. A google search reports that others have the same problem. Has anyone successfully figured out how to rotate a monitor on Windows Server 2003 with an ATI card?

  Read the article

• SCO UNIX problem: "Cannot create /var/adm/utmp or /var/adm/utmpx"

  - by Maktouch

  Hey everyone, I have an old server that doesn't boot. I don't know the version of unix installed, but I see SCO UNIX. It stops with that error: UX:init: ERROR: Cannot create /var/adm/utmp or /var/adm/utmpx UX:init: ERROR: failed write of utmpx entry: " " UX:init: ERROR: failed write of utmpx entry: " " UX:init: INFO: SINGLE USER MODE After that message, it just stops. I cannot write or press anything. Even CTRL + ALT + DEL does not work. I cannot get into the system. I have tried booting with a DamnSmallLinux LiveCD but it does not recognize the file system on HDA. Is there a way to either log in as root or bypass this error? Thanks.

  Read the article

• How to share a VPN connection in a VMWare Guest VM with the Host

  - by Jonathan

  The need - This question is relevant for all of those who want to bypass their corporate's annoying VPN, and access their work/corporate network from their private computer, especially if the corporate VPN client software can't run on their private computer. Homework: this question is very similar to this one and this one, which aren't answered :( The challange - Can't run the corporate VPN client from the private computer, so converted the work laptop to a VMWare Virtual Machine. The VPN client is working fine inside the Guest VM, now we want to share it with the Host (the private computer) The specs: * The private computer (Host OS) is Mac OS X Lion 64bit * The corporate laptop (Guest VM) is WinXP 32bit, running in Bridged network mode * The VPN client on the Guest VM is is Checkpoint SecuRemote NGX R60 HFA03 * While the VPN is running in the Guest VM, the Host can still ping the Guest and vice versa

  Read the article

• What prevents Windows from entering standby?

  - by Arne

  Is there a tool or method to find out, what prevents Windows Vista 32 bit from entering the standby mode? My home pc is set to standby after a certain time of inactivity. But quite often it just stays awake and I have know idea why. I know of things that will keep it awake and already checked devices and network to no avail. I suspect there is some application or service that tells the os to stay active and I hope there is some tool to find the culprit.

  Read the article

• how to fix asyncmac.sys infection

  - by Jay

  AVG anti-virus tells me that there is a virus in my asyncmac.sys. I tried to overwrite it with a copy of asyncmac.sys from another computer (making sure that it was the same version of Windows XP, but I was still nervous that I was going to break something), but when I reboot, I get the same virus warning. If I try to delete the file Windows (or somebody) automatically and immediately puts it back. I get a blue-screen death if I try to boot in safe mode. I tried to do a system restore to before I had the virus, but it tells me that it can't restore because nothing has changed. Any suggestions on how to fix this?

  Read the article

• Getting Correct Edition of Office 2007 from Serial Key

  - by Lloyd Sparkes

  I have been asked by a Client to refresh one of their Machines. To do this i managed to get Windows XP Setup to run in Repair mode, and while in setup i ran a serial key grabber, which grabbed the key for Office 2007 The only thing is that the key grabber didnt tell me what edition of Office 2007 was installed. I have aqquired a number of ISO's for the different editions (Home & Student, Standard, Professional, Ultimate) but the key doesnt work in any of them. Is there a way to get the edition from the Serial Key, or is there a generic ISO that will install any edition depending on the Serial Key?

  Read the article

• can I force server to always use turboboost?

  - by javapowered

  I'm using HP DL360p Gen8 with 2 * Xeon E5-2640. I do not load CPU 100%, i load it only ~10% and so I guess turboboost is not activated. However I'm using my server for trading so I absolutely don't care about CPU loading but I always want to process my data asap. So I want server to operate using maximum 3 GHz. I.e. 90% of CPU time I don't have anything to process. 10% of CPU time I have data to process. But I need to process it ASAP. I need every single microsecond. So I want server to operate always at maximum "turboboosted" mode. Is it possible?

  Read the article

• Is it possible to use the MMM tool without virtual IP capability?

  - by Artem

  We are on a host (Serverbeach) that does not support Virtual/floating IPs until you reserve at least a half-rack, which is just a little more than we are willing to spend per month right now. We do have 2 machines in one of their datacenters, and I am using these 2 machines right now in the Master-Master in Active-Passive Mode just like done by MMM -- http://mysql-mmm.org/. I have just set them up and I managing them manually, with manual switch on the Web frontend to tell it to connect to the correct (active) master. Is there any way to use MMM without virtual IPs? Any other comments on this setup?

  Read the article

• How to type a small fraction in Word 2007 equation editor?

  - by Timwi

  In Word 2007’s equation editor, I can enter “1/2” and I will get a properly formatted fraction. However, there is another kind of fraction that uses a smaller font size. How do I type that one using the keyboard alone? I notice that if I switch to linear mode, I get a small box displayed: Using the clipboard, I find that this is the same box (U+25A1) that I also get if I type “\box”. Despite, typing “\box(1/2)” still turns into a normal-size fraction and not the small fraction. How do I type the small fraction?

  Read the article

< Previous Page | 345 346 347 348 349 350 351 352 353 354 355 356  | Next Page >