Search Results

Search found 36652 results on 1467 pages for 'linux device driver'.

Page 350/1467 | < Previous Page | 346 347 348 349 350 351 352 353 354 355 356 357  | Next Page >

• Cent OS ifcfg configuration for ranges of IP's with different netmask

  - by Aaron Schlegel

  I have 1 set of 30 public IP's with a netmask of 255.255.255.0 and another set of 30 IP's with a netmask of 255.255.255.128. Both sets of IP's also have different gateways. How can I virtually assign the IP's to the machine? I have tried creating ifcfg-eth0:0 ifcfg-eth0:1 ifcfg-eth0:X ect for each IP. Below is my ifcfg file with. I have this for each IP with the correct gateway IP and netmask for each of my 60 IP's. If I do ip addr show it does show all of the 60 addresses with the correct broadcast IP and netmask. However I can only use 30 of my IP's that are from the same netmask. Am I doing this correctly? If the IP's show up with ip addr show does that mean I have correctly assigned them to the machine virtually? I want to check before I blame my hosting company for not routing the IP's correctly. DEVICE="eth0:1" BOOTPROTO="static" DNS1="**.**.**.**" DNS2="**.**.**.**" GATEWAY="2**.**.***.126" HOSTNAME="localhost.localdomain" HWADDR="0*:19:**:**:**:**" IPADDR="2**.*.**.**" IPV6INIT="no" MTU="1500" NETMASK="255.255.255.128" NM_CONTROLLED="yes" ONBOOT="yes" TYPE="Ethernet" Also is there a better way to do this? I have used ifcfg-eth0:0-range1 before to assign a range of IP's from the same netmask. Is it possible to do this with ranges with different netmask? Thanks!

  Read the article

• Default route not on LAN

  - by jarmund

  I have a network that in principle looks like this: H1---\ /----Inet1 H2---->---GW1---< H3---/ \----GW2-----Inet2 H1 and H2 = Hosts that need access to internet with GW1 Inet1 = Internet link over 3G connection Inet2 = 5GHz link to Internet (not always up) GW1 = Works as a router, automatically picking the "best" connection between Inet1 and Inet2 (the latter via GW2). GW2 = 5GHz wifi router And here's the problem: H3 only needs internet access when Inet2 is up. What i was thinking of doing was a routing table that looks like this: route to GW2 via GW1 default route is via GW2 I first set the route to GW2 via GW1 without a problem. But when i try route add default gw 1.2.3.4 (1.2.3.4 being the IP of GW2), it complains "SIOCADDRT: No such device" Is the problem that the default gw i'm trying to set is not reachable directly? Is there a different approach that would allow me to achieve this? An alternative (and hypothetical) approach: Since H3 will be using a static IP, is it possible to do some magic with iptables on GW1 to forward any packets from H3 to GW3, thereby "tricking" H3 into using GW2 as its default router?

  Read the article

• ADSL with RFC 2684 Bridging

  - by Axel Isouard

  My new ADSL line is now enabled, I can finally use my Netgear DM111Pv2 to use to the Internet. My ISP has told me a big surprise : I don't need to use a login and a password to connect to the Internet, then I must use the RFC 2684 bridging mode. It works pretty fine on the ADSL modem's side, but I've spent one night trying to figure out how to connect to the Internet through this modem. I only have a Fonera 2.0n and a computer running Gentoo Linux. I've been trying to use the br2684ctl utility with brctl on my Gentoo, first I've configured my kernel in that way : CONFIG_PPP=y CONFIG_PPP_BSDCOMP=y CONFIG_PPP_DEFLATE=y # CONFIG_PPP_FILTER is not set CONFIG_PPP_MPPE=y # CONFIG_PPP_MULTILINK is not set CONFIG_PPPOATM=y CONFIG_PPPOE=y CONFIG_PPP_ASYNC=y CONFIG_PPP_SYNC_TTY=y [...] CONFIG_ATM=y CONFIG_ATM_CLIP=y CONFIG_ATM_CLIP_NO_ICMP=y CONFIG_ATM_LANE=y CONFIG_ATM_MPOA=y CONFIG_ATM_BR2684=y # CONFIG_ATM_BR2684_IPFILTER is not set And I still get these messages : cirus nais # br2684ctl -b -c 0 -e 0 -a 8.35 br2684ctl[8041]: Interface "nas0" created sucessfully br2684ctl[8041]: Communicating over ATM 0.8.35, encapsulation: LLC br2684ctl[8041]: Fatal: failed to connect on socket; No such device The brctl utility keeps telling me "Invalid argument" each time I try to add the nas0 interface into my bridge, I'm honestly hoping I'm doing wrong. I've been following this README carefully and this tutorial on setting up a PPPoE connection with Gentoo, but the PPPoE interface just tries to start, and nothing special related to PPP happens, I can't see the interface when I do ifconfig. So, I'm asking you if there's something huge I've been missing since the beginning ! Maybe I should wait to buy a new router fully supporting the RFC2684 bridging mode, but I'm more interested in setting up this mode on my Fonera 2.0n and even my Raspberry Pi !

  Read the article

• Getting a TTY in a Connectback Shell

  - by Asad R.

  I'm often asked by friends to help with small Linux problems, and more often than not I'm required to login to the remote system. Usually there are a lot of issues with making an account and logging in (sometimes the box is behind a NAT device, sometimes SSHD isn't installed, etc.) so I usually just ask them to make a connect-back shell using netcat (nc -e /bin/bash ). If they don't have netcat I can just ask them to grab a copy of a statically compiled binary which isn't that hard or time consuming to download and run. Though this works well enough for me to enter simple commands, I can't run any apps that require a tty (vi, for example) and can't use any job control functions. I managed to bypass this issue by running in.telnetd with a few arguments within the connect-back shell that would assign me a terminal and drop me to a shell. Unfortunately in.telnetd isn't usually installed by default on most systems. What's the easiest way to get a fully functional connect-back terminal shell without requiring any non-standard packages? (A small C program that does the job would be fine as well, I just can't seem to find much documentation on how a TTY is assigned/allocated. A solution that doesn't require me to plough through the source code for SSHD and TELNETD would be nice :))

  Read the article

• How to restrict zone transfers to specific authorized servers only

  - by JonoB

  I recently failed a PCI compliance scan because of the following: This DNS server allows unrestricted zone transfers. Attackers may be able to use this information to gain knowledge on the structure of your networks to aid in device discovery prior to an actual attack. And the suggested solution is as follows: Reconfigure this DNS server to restrict zone transfers to specific authorized servers only. I am running a dedicated Linux Centos server. My understanding is that I have to edit the /etc/named.conf file, which I have done and the the relevant part is as follows: options { acl "trusted" { 127.0.0.1; xxx.xxx.xxx.001; //this is one of the server's ip's xxx.xxx.xxx.002; //this is another server's ip }; allow-recursion { trusted; }; allow-notify { trusted; }; allow-transfer { trusted; }; }; I then restarted the named service /etc/rc.d/init.d/named restart and requested a re-scan, which failed again for the same reason. Am I missing something obvious here?

  Read the article

• Sharing disk volumes across OpenVZ guests to reduce Package Management Overhead

  - by andyortlieb

  Is it feasible to create a single "master" OpenVZ guest who would only be used for package management, and use something like mount --bind on several other OpenVZ guests sort of trick them into using the environment installed by the master guest? The point of this would be so that users can maintain their own containers, and yet stay in sync with the master development environment, so they'll always have the latest & greatest requirements without worrying too much about system administration. If they need to install their own packages, could put them in /opt, or /usr/local (or set a path to their home directory)? To rephrase, I would like several (developer's, for example) OpenVZ guests whose /bin, /usr (and so on...) actually refer to the same disk location as that of a master OpenVZ guest who can be started up to install and update common packages for the environment to be shared by all of this group of OpenVZ guests. For what it's worth, we're running Debian 6. Edit: I have tried mounting (bind, and readonly) /bin, /lib, /sbin, /usr in this fashion and it refuses to start the containers stating that files are already mounted or otherwise in use: Starting container ... vzquota : (error) Quota on syscall for id 1102: Device or resource busy vzquota : (error) Possible reasons: vzquota : (error) - Container's root is already mounted vzquota : (error) - there are opened files inside Container's private area vzquota : (error) - your current working directory is inside Container's vzquota : (error) private area vzquota : (error) Currently used file(s): /var/lib/vz/private/1102/sbin /var/lib/vz/private/1102/usr /var/lib/vz/private/1102/lib /var/lib/vz/private/1102/bin vzquota on failed [3] If I unmount these four volumes, and start the guest, and then mount them after the guest has started, the guest never sees them mounted.

  Read the article

• Windows won't sleep after booting from grub

  - by mkasberg

  I recently added a second hard drive to my computer and I am using it do dual-boot Linux (Ubuntu 12.04) with Windows 7. Both hard drives are SATA. I am using the default grub bootloader on my second hard drive. The windows drive is unmodified. To get to grub, I changed the hard disk boot priority in my BIOS (P35-DS3L) to boot from the second drive. The problem I'm having is that when I boot to Windows 7 (on sda) from grub (on sdb), Windows 7 will not go to sleep (from the start menu). The display shuts off momentarily as if its going to sleep, then comes back on and displays the switch-user screen. Powercfg -lastwake does not show anything. I am sure that this is related to booting from grub on sdb because when I change the hard disk boot priority in the BIOS to boot from my (unmodified) Windows hard disk, the computer goes to sleep fine. It occurred to me that installing grub on sda might solve the problem, but I'd rather not since I like to have my windows hard disk unmodified so that booting to it from the BIOS boots directly to windows. A possible work around is to use the BIOS as a bootloader, by pressing F8 to select the boot device. Still, I'd like to know why the problem is happening in the first place.

  Read the article

• Best option for storage clustering

  - by sam

  I'm working on an application that requires a large amount of storage space and I want to handle storage 'in-house' (Much cheaper than, say, S3) so we will have multiple servers (Initially 4) with large amounts of storage (6TB each). The storage will need to be very flexible and configurable, each piece of data should be replicated on at least 2 servers and must be easily readable/writable from ether an API of a UNIX device/file/folder like a normal drive, I don't mind which. We must also be able to easily offload content to our HTTP CDN (Edgecast), it doesn't need to have built in HTTP support but if it doesn't I'm going to have to write something to get the files onto HTTP so they can be pulled by the CDN. I've looked at a lot of solutions including Eucalyptus Walrus OpenStack Object Storage MogileFS and some others which I can't remember All the servers will be running RHEL 6, they have 4x1.5TB drives which will be RAID1'd into a single partition. All the servers have 1GB/s connections between them and 100MB/s connections to the internet with unlimited bandwidth. They have 2x2.66ghz processors. I understand there isn't a single, perfect answer but it would be nice to get some pointers.

  Read the article

• needing storage integrity (write/read) test - for BASH

  - by Mr. Bash

  In need of shell scripts / bash commands to verify data integrity of local harddrives, usb-drives, etc, ... Like the famous www.heise.de/download/h2testw; or something that is at least common within repositories. (h2testw writes a specific datastring over and over onto the medium, then reads it again to verify if it was written correctly and displays write/read time/speed.) please no dd if=/dev/random of=/dev/sdx bs=1k && dd if=/dev/sdx of=/dev/null bs=1k since it won't verify if everything was written correctly. It is only a test if read/write is successful to the device. So far, I'm not too happy with badblocks -w -v /dev/sdx1 either, since it seems rather slow and I don't know what it exactly writes, and if it considers wear-leveling on flash media. There is also a program named F3 http://oss.digirati.com.br/f3/ that needs to be compiled. Designed after h2testw, the concept sounds interesting, i'd just rather have it as a ready to go bash script.

  Read the article

• Is it possible to mount a disk image, created with dd, to a directory on a mounted external usb hdd?

  - by Keeper Hood

  I have an image of my home (/dev/sda3) partition, which I've created using the "dd" command. dd if=/dev/sda3 of=/path/to/disk.img I've deleted the home partition via gparted in order to enlarge my /dev/root partition. Then I've recreated the /dev/sda3 partition which is smaller in size then the one I've backed up to the image. I was wondering since I have a 2TB external HDD, could it be possible to mount my backed up image on the external HDD and then copy the files into the /home directory. Since the external HDD would be already in a "mounted state", I'm unsure whether this is a good idea, mounting on a mounted device. I'm running Slackware 13.37 (64bit). used ext4 on all the partitions. resized the root partition with gparted live cd. I've tried mount -t ext4 /path/to/disk.img /mng/image -o loop It gave me an fs error (wrong fs type, bad option, bad superblock on dev/loop/0) Then i did dmesg | tail which outputs: EXT4-fs (loop0) : bad geometry: block count 29009610 exceeds size of defice (1679229 blocks) I have no idea what to do, I want to restore my /home data from the image I've backed up.

  Read the article

• Debian software raid 1: boot from both disk

  - by bsreekanth

  I newly installed debian squeeze with software raid.The way I did was, as also given in this thread. I have 2 HDD with 500 GB each. For each of them, I created 3 partitions (/boot, / and swap) I selected the hard drive and created a new partition table I created a new partition that was 1GB. I then specified to use the partition as a Physical Volume for RAID. and used for /boot and enabled bootable. Created another partition, which is of 480 GB, and then specified to use the partition as a Physical Volume for RAID. and used for /. Created another partion and used for swap Then RAID configuration: Through Configure RAID menu - create MD device - (2 for the number of drives, 0 for spare devices) Next select the partitions you want to be members of /dev/MD0. I selected /dev/sda1 and /dev/sdb1 (for /boot) Next select the partitions you want to be members of /dev/MD1. I selected /dev/sda6 and /dev/sdb6 (for /) And no RAID for swap partitions 'Finish Partitioning and write changes to disk' -- Finish the rest of the install like normal Everything is ok now, except I am not sure how to test my raid config. When I pull the power of the HDD, it only boots from one disk. I read in some forum that I may have to install GRUB manually on the other. In Debian Squeeze, there is no grub command. Not sure how to make my software raid bootable from both disk. Also, please comment on my steps above. Anything unusual. I configured /boot partitions of both disks to be boot=yes. Not sure whether that is ok. Thanks, Bsr

  Read the article

• DBD::Advantage and 64-bit Perl - Always 6060

  - by WarheadsSE

  I realize that I am attempting to go beyond the "supported" behavior of the manf's released drivers for perl, after all they have only released it in package with x86 .so's. However, since I cannot use their package with x64 Perl on a RHEL 5.4 x86_64 box, and maintaining a seperate install of x86 perl just for this one package, I have made an attempt to get this puppy working thanks to released 64-bit .so's that accompany other driver packages for Advantage. What I have done to this point: download beta 10 DBI drivers, in 32 download beta 10 PHP extension (it contains 32 and x86_64) copy the required DLLs into the ads-lib location (eg /usr/local/ads/lib64) compile the Perl DBI driver with the path to the lib64's .so's Good compilation, good install, good use. The problem is that I always get : failed: [iAnywhere Solutions][Advantage SQL][ASA] Error 6060: Advantage Database Server not available on specified server. axServerConnect (SQL-HY000)(DBD: db_login/SQLConnect err=-1) Does anyone have any ideas? EDIT: fixed package name in post title

  Read the article

• Clock problem with FTDIchip FT2232 MPSSE mode

  - by Simi

  Hello, I'm trying to write/read to an extern device connected to a FTDIchip FT2232 MPSSE mode using SPI. I'm using the SPI function given by FTDI for Labview. I'm doing this: Open_Device - Init_Device - Write/Read - Close_Device The problem is that I don't have a clock signal on the scope when I try to read/write. Do you have a solution? Thanks

  Read the article

• tftpd-hpa service must be restarted before working after fresh boot

  - by Steve

  I'm running Ubuntu 12.04 inside a VirtualBox VM. I've installed tftpd-hpa so I can boot an embedded Linux device via tftp. My problem is that after a fresh boot of the VM, tftpd doesn't seem to work until I restart the service, after which is works great until the system is rebooted. The transcript below should explain the situation. EDIT: After the fresh boot, I execute netstat -a | grep tftp and find nothing. After restarting the service, the same command returns udp 0 0 *:tftp *:* (whitespace removed). I think this might be the key to the problem, I'm just not sure how to resolve it. I don't think it's related to this specific issue, but I had another problem with tftpd that was asked and answered in this question. steve@steve-VirtualBox:~$ cat /etc/default/tftpd-hpa # /etc/default/tftpd-hpa TFTP_USERNAME="tftp" TFTP_DIRECTORY="/var/lib/tftpboot" TFTP_ADDRESS="0.0.0.0:69" TFTP_OPTIONS="--secure" steve@steve-VirtualBox:~$ ls -l /var/lib/tftpboot total 8204 -rw-r--r-- 1 root root 34352 May 28 08:22 am335x-boneblack.dtb -rw-r--r-- 1 root root 33206 May 28 08:22 am335x-bone.dtb -rw-r--r-- 1 root root 41564 May 28 08:22 am335x-evm.dtb -rw-r--r-- 1 root root 38048 May 28 08:22 am335x-evmsk.dtb -rwxr-xr-x 1 root root 4117904 May 20 09:39 zImage -rw-r--r-- 1 root root 4117616 May 28 08:22 zImage-am335x-evm.bin steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Transfer timed out. tftp> quit steve@steve-VirtualBox:~$ sudo service tftpd-hpa restart [sudo] password for steve: tftpd-hpa stop/waiting tftpd-hpa start/running, process 2106 steve@steve-VirtualBox:~$ tftp localhost tftp> get zImage Received 4143798 bytes in 1.4 seconds tftp> quit steve@steve-VirtualBox:~$

  Read the article

• Openldap with ppolicy

  - by nitins

  We have working installation of OpenLDAP version 2.4 which is using shadowAccount attributes. I want to enable ppolicy overlays. I have gone through the steps provided at OpenLDAP and ppolicy howto. I have made the changes to slapd.conf and imported the password policy. On restart OpenLDAP is working fine and I can see the password policy when I do a ldapsearch. The user object looks like given below. # extended LDIF # # LDAPv3 # base <dc=xxxxx,dc=in> with scope subtree # filter: uid=testuser # requesting: ALL # # testuser, People, xxxxxx.in dn: uid=testuser,ou=People,dc=xxxxx,dc=in uid: testuser cn: testuser objectClass: account objectClass: posixAccount objectClass: top objectClass: shadowAccount shadowMax: 90 shadowWarning: 7 loginShell: /bin/bash uidNumber: 569 gidNumber: 1005 homeDirectory: /data/testuser userPassword:: xxxxxxxxxxxxx shadowLastChange: 15079 The password policy is given below. # default, policies, xxxxxx.in dn: cn=default,ou=policies,dc=xxxxxx,dc=in objectClass: top objectClass: device objectClass: pwdPolicy cn: default pwdAttribute: userPassword pwdMaxAge: 7776002 pwdExpireWarning: 432000 pwdInHistory: 0 pwdCheckQuality: 1 pwdMinLength: 8 pwdMaxFailure: 5 pwdLockout: TRUE pwdLockoutDuration: 900 pwdGraceAuthNLimit: 0 pwdFailureCountInterval: 0 pwdMustChange: TRUE pwdAllowUserChange: TRUE pwdSafeModify: FALSE I do not what should be done after this. How can the shadowAccount attributes be replaced with the password policy.

  Read the article

• Is it possible to stop the "Beep" device on all computers in a Windows network?

  - by sharptooth

  On Windows the default behavior it to make an annoying "beep" sound every time Windows things something notable happened. The result is that when someone send a company-wide email via the MS Exchange all computers around my cubicle beep one by one. This is annoying and makes no sense. Luckily beeping can be shut off. Someone has to: open the "Device Manager", select "View - Show hidden devices", find the "Beep" device in "Non-Pug and Play Devices" node, open its properties, go to the "Driver" tab, set "startup type" to "Disabled" and click "Stop". The "Beep" device will stop and no longer produce the useless sound. This solution however requires tracking every computer and then talking to its user which is not very convenient. Device Manager doesn't allow stopping a device on another computer. I'm looking for a solution that can be deployed by the administrators team. We have a domain and the administrators even install the programs company-wide automatically. Are there any means to stop the "Beep" device an all computers in the Windows network with some remote-administration features automatically?

  Read the article

• how to display IBitmapImage on CDC

  - by tommyk

  What is the best way to display IBitmapImage on a device context. I am using Windows CE 6.0. void CImaginingTestView::OnDraw(CDC* pDC) { CImaginingTestDoc* pDoc = GetDocument(); ASSERT_VALID(pDoc); IBitmapImage* pBitmapImage = pDoc->GetBitmapImage(); if (pBitmapImage) { // how to draw my bitmap on a pDC ?? } }

  Read the article

• How to stop RAID5 array while it is shown to be busy?

  - by RCola

  I have a raid5 array and need to stop it, but while trying to stop it getting error. # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sde1[3](F) sdc1[4](F) sdf1[2] sdd1[1] 2120320 blocks level 5, 32k chunk, algorithm 2 [3/2] [_UU] unused devices: <none> # mdadm --stop mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: No devices given. # mdadm --stop /dev/md0 mdadm: metadata format 00.90 unknown, ignored. mdadm: metadata format 00.90 unknown, ignored. mdadm: fail to stop array /dev/md0: Device or resource busy and # lsof | grep md0 md0_raid5 965 root cwd DIR 8,1 4096 2 / md0_raid5 965 root rtd DIR 8,1 4096 2 / md0_raid5 965 root txt unknown /proc/965/exe # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sde1[3](F) sdc1[4](F) sdf1[2] sdd1[1] 2120320 blocks level 5, 32k chunk, algorithm 2 [3/2] [_UU] # grep md0 /proc/mdstat md0 : active raid5 sde1[3](F) sdc1[4](F) sdf1[2] sdd1[1] # grep md0 /proc/partitions 9 0 2120320 md0 While booting, md1 is mounted ok but md0 failed for some unknown reason # dmesg | grep md[0-9] [ 4.399658] raid5: allocated 3179kB for md1 [ 4.400432] raid5: raid level 5 set md1 active with 3 out of 3 devices, algorithm 2 [ 4.400678] md1: detected capacity change from 0 to 2121793536 [ 4.403135] md1: unknown partition table [ 38.937932] Filesystem "md1": Disabling barriers, trial barrier write failed [ 38.941969] XFS mounting filesystem md1 [ 41.058808] Ending clean XFS mount for filesystem: md1 [ 46.325684] raid5: allocated 3179kB for md0 [ 46.327103] raid5: raid level 5 set md0 active with 2 out of 3 devices, algorithm 2 [ 46.330620] md0: detected capacity change from 0 to 2171207680 [ 46.335598] md0: unknown partition table [ 46.410195] md: recovery of RAID array md0 [ 117.970104] md: md0: recovery done. # cat /proc/mdstat Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md0 : active raid5 sde1[0] sdf1[2] sdd1[1] 2120320 blocks level 5, 32k chunk, algorithm 2 [3/3] [UUU] md1 : active raid5 sdc2[0] sdf2[2] sde2[3](S) sdd2[1] 2072064 blocks level 5, 128k chunk, algorithm 2 [3/3] [UUU]

  Read the article

• Bootable GRUB partition

  - by MA1

  I have a customized live fedora 12 USB which is working fine. What i want to do is to make a partition of my hard disk bootable so that my customized fedora can be run from hard disk. To accomplish this i did the following steps: Created a primary partition(/dev/sda2) and format it as ext3 and set it as active. Copy all the files in the live usb to /dev/sda2. Following are the live usb contents(all directories): a. boot b. EFI c. LiveOS d. syslinux Then i installed the GRUB in boot/grub Created the grub.conf in boot/grub Following are the contents of each directory in the USB: syslinux/ boot.cat isolinux.bin splash.jpg vesamenu.c32 initrd0.img ldlinux.sys syslinux.cfg vmlinuz0 LiveOS/ livecd-iso-to-disk osmin.img squashfs.img EFI/ boot/ boot.conf grub.conf boot.efi bootia32.conf bootia32.efi splash.jpg splash.xpm.gz vesamenu.c32 initrd0.img isolinux.bin isolinux.cfg vmlinuz0 boot/grub/ core GRUB files grub.conf olpc.fth Following are contents of grub.conf default=0 splashimage=/EFI/boot/splash.xpm.gz timeout 2 hiddenmenu title funLinux kernel /EFI/boot/vmlinuz0 root=live:LABEL=myFun rootfstype=auto ro liveimg quiet ssb.blacklist=1 selinux=0 vga=normal nomodeset rhgb initrd /EFI/boot/initrd0.img Now when i try to boot from the hard disk it shows the grub menu and fedora starting to load but during loading it said No root device found Boot has failed, sleeping forever So, where is the problem? what i am doing wrong?

  Read the article

• VNC failure on Xen

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Fresh Proxmox VE 2.1 installation with defaults can't be reached or pinged

  - by Damainman

  I am using the lastest Proxmox VE 2.1. My server has two NICS with a uplink only connected into eth0. My Server is a co-located server utilizing public IPv4 IPs. It is not behind a firewall or any system which monitors traffic. Via IPKVM I did a fresh install of Proxmox, I put in the correct IP, Mask, Gateway, and DNS information. The install went perfectly fine with no errors. Upon completion and rebooting the system: I am unable to reach the web GUI via the browser, it just times out. I am unable to ping the server. I am unable to ping outside to the Internet from within the server. Tried pinging out to 4.2.2.2 and yahoo.com I tried rebooting the server and restarting the network service. IFCONFIG shows my IP information under vmbro0 which also has the same MAC address as the eth0 device. eth0 only displays a IPv6 Scope:Link address, which I did not setup myself. This is my first time installing proxmox, but after searching for a few hours it doesn't seem like anyone else is having the same issue as me from a fresh install with just the defaults. So far the only thing I did was install it. Also, I know the network cable is good and the IP is good because I was running a Xen XCP server with the same network settings prior to wiping it to install proxmox. Some additional information: for pveversion -v (Installed proxmox-ve_2.1-f9b0f63a-26.iso) pve-manager: 2.1-1 (pve-manager/2.1/f9b0f63a) running kernel: 2.6.32-11-pve proxmox-ve-2.6.32: 2.0-66 netstat -nr (note: .136 is my network, and .137 is my gateway) Destination - Gateway - Genmask xxx.xxx.xxx.136 - 0.0.0.0 - 255.255.255.248 0.0.0.0 - xxx.xxx.xxx.137 - 0.0.0.0 /etc/network/interfaces auto lo iface lo inet loopback auto vmbr0 iface vmbr0 inet static address xxx.xxx.xxx.138 netmask 255.255.255.248 gateway xxx.xxx.xxx.137 bridge_ports eth0 bridge_stp off bridge_fd 0

  Read the article

• Ubuntu lucid, maverick high iowait

  - by netom

  I'm using Ubuntu, and I've got the same problem with Lucid and Maverick. From time to time, especially a few minutes after boot, the iowait goes between 50-100% and the box is unusable. Everything that tries to access the disk freezes. I have the following setup: Hard disk: Model Family: Western Digital Caviar Green family Device Model: WDC WD15EADS-00P8B0 Serial Number: WD-WMAVU0391287 Firmware Version: 01.00A01 User Capacity: 1.500.301.910.016 bytes I have a quad core Intel Core2 Q6600 processor, and 4G of memory. When the high iowait occurs, usually 4 processes are active: kdmflush (two procs) jbd2/dm-0-8 jbd2/db-1-8 and a few more starving user processes of course. I know this from top and iotop. Any suggestions about why this is happening? There are a lot of q/a-s about linux and high iowait, but none of them helped so far, I even tweaked the hard disk not to park the head in every 8 seconds (Load cycle count is 50334!!!!! :o ), but nothing. Problem persists. Thank you in advance.

  Read the article

• JBD: Spotted dirty metadata buffer

  - by Jake Mach

  Sep 25 22:19:38 host kernel: [7798806.146942] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 267). There's a risk of filesystem corruption in case of system crash. Sep 25 22:19:38 host kernel: [7798806.146956] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 1). There's a risk of filesystem corruption in case of system crash. Sep 25 22:19:38 host kernel: [7798806.146967] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 353). There's a risk of filesystem corruption in case of system crash. Sep 25 22:19:38 host kernel: [7798806.147121] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 353). There's a risk of filesystem corruption in case of system crash. Sep 25 22:19:38 host kernel: [7798806.147133] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 1). There's a risk of filesystem corruption in case of system crash. Sep 25 22:19:38 host kernel: [7798806.147143] JBD: Spotted dirty metadata buffer (dev = loop0, blocknr = 267). There's a risk of filesystem corruption in case of system crash. [7817859.850517] EXT4-fs error (device loop0): ext4_mb_generate_buddy: EXT4-fs: group 1: 28618 blocks in bitmap, 29028 in gd what does this mean? how did this happen?

  Read the article

• VNC on Xen failure

  - by BCable

  The following config works and creates a good VM in Xen: # Kernel Setup kernel = "/boot/vmlinuz-2.6.18.8-xenU" # Memory memory = "256" # Disk disk = [ "file:/opt/xen/domains/110/sda1.img,sda1,w", "file:/opt/xen/domains/110/swap.img,sda2,w" ] # container name name = "110" hostname = "boo" # Networking vif = ["type=ieomu, bridge=xenbr0"] # VNC vnc = 1 #vfb = [ 'type=vnc,vncdisplay=2,vnclisten=0.0.0.0,vncpasswd=110' ] # Behavior Settings root = "/dev/sda1" extra = "fastboot" But when I uncomment the VFB line, I get the following error after it hangs for at least 30 seconds: [root@customer 110]# xm create boo.cfg Using config file "./boo.cfg". Error: Device 0 (vkbd) could not be connected. Hotplug scripts not working. Any ideas? Part two of this question: Sometimes it actually works, and a port is opened. When this happens, nmap shows the VNC ports open and I can connect via the VNC client, but it just hangs at "Connection established." and no VNC display shows up. I've tried multiple VNC clients (TightVNC, TightVNC Java Console, RealVNC), but they all fail to connect. Does VNC through Xen require X to be started in order to function? I was under the impression that it would show the console screen, so I'm confused as to why all these issues are occurring. Thanks!

  Read the article

• Can Xen be configured to dedicate only one port of a dual-port NIC to a domU?

  - by jamieb

  I'm using CentOS 5.4 on my dom0 with a stock Xen kernel. I'm attempting to use the pciback module to hide some of the Ethernet ports from the host and reserve them for a domU I intend to use for a firewall (process described here). However, when I launch the domU, I get the following error message: Using config file "/etc/xen/firewall". Error: pci: improper device assignment specified: pci: 0000:01:04.0 must be co-assigned to the same guest with 0000:01:06.0, but it is not owned by pciback. lspci gives me the following output: 00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02) 00:02.0 VGA compatible controller: Intel Corporation 82945G/GZ Integrated Graphics Controller (rev 02) 00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01) 00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1) 00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01) 00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01) 01:04.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) From the sound of the error message, it seems like I also need to dedicate eth0 (PCI ID 01:04.0) to the domU. Am I correct? If not, what am I doing wrong? Thanks!

  Read the article

< Previous Page | 346 347 348 349 350 351 352 353 354 355 356 357  | Next Page >