Search Results

Search found 15137 results on 606 pages for 'global state'.

Page 351/606 | < Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358 | Next Page >

New CAT5 cable run is unstable - bad jacks? Bad cable?

- by BeemerGuy

This is a little project I'm doing at home. I wanted to wire two rooms together (basically, the router is one room, and the switch is in the second room). So I ran a CAT5 between the two rooms, and wired an RJ45 jack in each room. I then hooked up the two jacks with two CAT5 cable to run it through the cable tester, and all 8 wires seem good. Now, when I connect the switch and the router, the connection is unstable -- I ping the router and it barely holds on for two pings before it disconnects, and stays in that unstable state. Just to make sure the router and the switch are ok, I connected them with long wire between the two rooms and the connection is absolutely stable, and pings continuously. What could be the cause for the unstable connection? Especially that it pings a few times, so there IS a connection. But why is it unstable? And how come the cable tester says it's ok, but it's unstable?

Read the article
puppet master REST API returns 403 when running under passenger works when master runs from command line

- by Anadi Misra

I am using the standard auth.conf provided in puppet install for the puppet master which is running through passenger under Nginx. However for most of the catalog, files and certitifcate request I get a 403 response. ### Authenticated paths - these apply only when the client ### has a valid certificate and is thus authenticated # allow nodes to retrieve their own catalog path ~ ^/catalog/([^/]+)$ method find allow $1 # allow nodes to retrieve their own node definition path ~ ^/node/([^/]+)$ method find allow $1 # allow all nodes to access the certificates services path ~ ^/certificate_revocation_list/ca method find allow * # allow all nodes to store their reports path /report method save allow * # unconditionally allow access to all file services # which means in practice that fileserver.conf will # still be used path /file allow * ### Unauthenticated ACL, for clients for which the current master doesn't ### have a valid certificate; we allow authenticated users, too, because ### there isn't a great harm in letting that request through. # allow access to the master CA path /certificate/ca auth any method find allow * path /certificate/ auth any method find allow * path /certificate_request auth any method find, save allow * path /facts auth any method find, search allow * # this one is not stricly necessary, but it has the merit # of showing the default policy, which is deny everything else path / auth any Puppet master however does not seems to be following this as I get this error on client [amisr1@blramisr195602 ~]$ sudo puppet agent --no-daemonize --verbose --server bangvmpllda02.XXXXX.com [sudo] password for amisr1: Starting Puppet client version 3.0.1 Warning: Unable to fetch my node definition, but the agent run will continue: Warning: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /certificate_revocation_list/ca [find] at :110 Info: Retrieving plugin Error: /File[/var/lib/puppet/lib]: Failed to generate additional resources using 'eval_generate: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [search] at :110 Error: /File[/var/lib/puppet/lib]: Could not evaluate: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [find] at :110 Could not retrieve file metadata for puppet://devops.XXXXX.com/plugins: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /file_metadata/plugins [find] at :110 Error: Could not retrieve catalog from remote server: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /catalog/blramisr195602.XXXXX.com [find] at :110 Using cached catalog Error: Could not retrieve catalog; skipping run Error: Could not send report: Error 403 on SERVER: Forbidden request: XX.XXX.XX.XX(XX.XXX.XX.XX) access to /report/blramisr195602.XXXXX.com [save] at :110 and the server logs show XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/certificate_revocation_list/ca? HTTP/1.1" 403 102 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/file_metadatas/plugins?links=manage&recurse=true&&ignore=---+%0A++-+%22.svn%22%0A++-+CVS%0A++-+%22.git%22&checksum_type=md5 HTTP/1.1" 403 95 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:52 +0530] "GET /production/file_metadata/plugins? HTTP/1.1" 403 93 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:53 +0530] "POST /production/catalog/blramisr195602.XXXXX.com HTTP/1.1" 403 106 "-" "Ruby" XX.XXX.XX.XX - - [10/Dec/2012:14:46:53 +0530] "PUT /production/report/blramisr195602.XXXXX.com HTTP/1.1" 403 105 "-" "Ruby" thefile server conf file is as follows (and goin by what they say on puppet site, It is better to regulate access in auth.conf for reaching file server and then allow file server to server all) [files] path /apps/puppet/files allow * [private] path /apps/puppet/private/%H allow * [modules] allow * I am using server and client version 3 Nginx has been compiled using the following options nginx version: nginx/1.3.9 built by gcc 4.4.6 20120305 (Red Hat 4.4.6-4) (GCC) TLS SNI support enabled configure arguments: --prefix=/apps/nginx --conf-path=/apps/nginx/nginx.conf --pid-path=/apps/nginx/run/nginx.pid --error-log-path=/apps/nginx/logs/error.log --http-log-path=/apps/nginx/logs/access.log --with-http_ssl_module --with-http_gzip_static_module --add-module=/usr/lib/ruby/gems/1.8/gems/passenger-3.0.18/ext/nginx --add-module=/apps/Downloads/nginx/nginx-auth-ldap-master/ and the standard nginx puppet master conf server { ssl on; listen 8140 ssl; server_name _; passenger_enabled on; passenger_set_cgi_param HTTP_X_CLIENT_DN $ssl_client_s_dn; passenger_set_cgi_param HTTP_X_CLIENT_VERIFY $ssl_client_verify; passenger_min_instances 5; access_log logs/puppet_access.log; error_log logs/puppet_error.log; root /apps/nginx/html/rack/public; ssl_certificate /var/lib/puppet/ssl/certs/bangvmpllda02.XXXXXX.com.pem; ssl_certificate_key /var/lib/puppet/ssl/private_keys/bangvmpllda02.XXXXXX.com.pem; ssl_crl /var/lib/puppet/ssl/ca/ca_crl.pem; ssl_client_certificate /var/lib/puppet/ssl/certs/ca.pem; ssl_ciphers SSLv2:-LOW:-EXPORT:RC4+RSA; ssl_prefer_server_ciphers on; ssl_verify_client optional; ssl_verify_depth 1; ssl_session_cache shared:SSL:128m; ssl_session_timeout 5m; } Puppet is picking up the correct settings from the files mentioned because config print command points to /etc/puppet [amisr1@bangvmpllDA02 puppet]$ sudo puppet config print | grep conf async_storeconfigs = false authconfig = /etc/puppet/namespaceauth.conf autosign = /etc/puppet/autosign.conf catalog_cache_terminus = store_configs confdir = /etc/puppet config = /etc/puppet/puppet.conf config_file_name = puppet.conf config_version = "" configprint = all configtimeout = 120 dblocation = /var/lib/puppet/state/clientconfigs.sqlite3 deviceconfig = /etc/puppet/device.conf fileserverconfig = /etc/puppet/fileserver.conf genconfig = false hiera_config = /etc/puppet/hiera.yaml localconfig = /var/lib/puppet/state/localconfig name = config rest_authconfig = /etc/puppet/auth.conf storeconfigs = true storeconfigs_backend = puppetdb tagmap = /etc/puppet/tagmail.conf thin_storeconfigs = false I checked the firewall rules on this VM; 80, 443, 8140, 3000 are allowed. Do I still have to tweak any specifics to auth.conf for getting this to work?

Read the article
cassandra node discovery

- by eQuiNoX__

I just set up a 3 node system with ip addresses "192.168.0.101", "192.168.0.102", "192.168.0.103". I have set the seeds value on the configuration of all three machines as seeds: "192.168.0.101,192.168.0.102,192.168.0.103" However, on running nodetool on any of them, only the 103 machine gets discovered. node101:/opt/cassandra/apache-cassandra-0.8.5/bin# ./nodetool ring -h 192.168.0.101 Address DC Rack Status State Load Owns Token 192.168.0.103 datacenter1 rack1 Up Normal 151.96 KB 100.00% 38174485210079977599903748344879358256 Could someone tell me where the problem lies?

Read the article
Reversing an lvreduce of LVM to original size

- by praspa

On a RHEL system that uses LVM 2 with 4K blocks. Have been successful in reducing the LV, but trying to get steps to reverse the operation so that the LV returns to its original size. Using these steps to reduce the LV by 1GB, # umount /foo # e2fsk -f /dev/mylvm/foo # resize2fs /dev/mylvm/foo <Current LV Block count - 1GB/4K> # lvreduce --size <Current # GB - 1GB> /dev/mylvm/foo Then to reverse the reduction # lvextend --size <Original #GB> /dev/mylvm/foo # resize2fs /dev/mylvm/foo The reversal gets close to the orignal size. A 'df -h' reports that it seems to be about ~ 0.1GB shy of the original size. Using these utilities, is there a better procedure to shrink and grow the LV so that the original state can be recovered effectively?

Read the article
How to change Chrome default search engine from regional one to google.com without loosing search suggestion

- by Karsus Ren

I want to use google.com instead of google.com.hk as my default search engine in Chrome. I tried to use custom search engine, but they all break search suggestions, not even something like https://encrypted.google.com/search?q=%s&{google:RLZ}{google:acceptedSuggestion} {google:originalQueryForSuggestion}{google:assistedQueryStats} {google:searchFieldtrialParameter}sourceid=chrome&ie={inputEncoding} which include parameters like acceptedSuggestion that seems to imply seach suggestions being enabled. But no, search suggestions still don't work. In addition. some websites suggest editing Local State file under Chrome's setting folder. I already tried that, and it didn't work at all. So, is there any way to use google.com as default search engine without breaking search suggestions?

Read the article
Debian server doesn't free memory after backup

- by stan31337

I have production server that is running Debian 6.0.6 Squeeze #uname -a Linux debsrv 2.6.32-5-xen-amd64 #1 SMP Sun Sep 23 13:49:30 UTC 2012 x86_64 GNU/Linux Every day cron executes backup script as root: #crontab -e 0 5 * * * /root/sites_backup.sh > /dev/null 2>&1 #nano /root/sites_backup.sh #!/bin/bash str=`date +%Y-%m-%d-%H-%M-%S` tar pzcf /home/backups/sites/mysite-$str.tar.gz /var/sites/mysite/public_html/www mysqldump -u mysite -pmypass mysite | gzip -9 > /home/backups/sites/mysite-$str.sql.gz cd /home/backups/sites/ sha512sum mysite-$str* > /home/backups/sites/mysite-$str.tar.gz.DIGESTS cd ~ Everything works perfectly, but I notice that Munin's memory graph shows increase of cache and buffers after backup. Then I just download backup files and delete them. After deletion Munin's memory graph returns cache and buffers to the state that was before backup. Here's Munin graph: Unfortunately I don't have enough rep to add image here. So here's a link:

Read the article
delete key on linux does not work

- by Gauthier Fleutot

Hi! My delete key does not work in ubuntu, it does nothing. I understand that this is a common problem, but I could solve it with the information I found elsewhere. I ran xev. Pressing the 'a' key gives: KeyRelease event, serial 30, synthetic NO, window 0x2c00001, root 0x1a6, subw 0x0, time 7255643, (-113,-107), root:(425,300), state 0x2010, keycode 38 (keysym 0x61, a), same_screen YES, XLookupString gives 1 bytes: (61) "a" XFilterEvent returns: False Pressing 'Delete' gives: FocusOut event, serial 30, synthetic NO, window 0x2c00001, mode NotifyGrab, detail NotifyAncestor FocusIn event, serial 30, synthetic NO, window 0x2c00001, mode NotifyUngrab, detail NotifyAncestor KeymapNotify event, serial 30, synthetic NO, window 0x0, keys: 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 From there I don't know what to do. Help?

Read the article
Can't deploy an ejb bean on jboss

- by leo

I am try to deploy a jar to an jboss server. It works on my environment. But when I deployed the same jar on another server, i kept getting an error saying that the persistence unit is already registered. There is no other bean using the same name and the same persistence unit name. I tried to restart the server and remove the tmp, work, data directory but still get the same error. here is my error: ObjectName: jboss.j2ee:service=EJB3,module=wess_jpa.jar State: FAILED Reason: java.lang.RuntimeException: javax.management.InstanceAlreadyExistsException: persistence.units:unitName=dses_wess already registered. This is almost identical to this issue in jboss forum but there is no solution: http://www.jboss.org/index.html?module=bb&op=viewtopic&p=4211687#4211687

Read the article
Operation System Clone from a Motherboard to Another

- by Devian

Lately we had an idea with my Family of building a Super Computer from Scratch. So while we were planning on building our setup, one idea came to my head that it seems possible but i want also your opinions. Lets say that we have 2 ATX Motherboards and 1 MicroATX. Motherboard Setup: 1x ASUS Rampage Extreme Black Edition 1x Intel Core i7 4960x 4x GTX Titan 8x 8GB 1866 Ram Motherboard Setup: 1x SuperMicro X9DRG-QF 2x Intel Xeon E7-8890V2 1x nVIDIA QUADRO K6000 4x nVIDIA Tesla K40 128 GB 1866 Ram And imagine a Solid State Drive with a Switch connected to both of the MotherBoards Can i edit & copy all the data of The first motherboard's RAM to The Other's to be able to continue operating my current Operation System after switching the SSD to the Second Motherboard, from the Second MotherBoard and vice versa? Les say my "Switch Application" modifies everything the Kernel needs to believe nothing happend and continuing its operation from the same point the first motherboard stopped. (Changes on the Device List, CPU Cores, Drivers... etc)

Read the article
Linux: find thin server running on port 80 and kill it

- by Andrew

On my Linux server I ran: sudo thin start -p 80 -d Now I'd like to restart the sever. The trouble is, I can't seem to get the old process to kill it. I tried: netstat -anp But what I see on port 80 is this: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - So, it didn't give me a PID to kill... I tried pgrep -l thin but that gave me nothing. Meanwhile pgrep -l ruby gives me like 6 processes running. I don't really understand why multiple ruby threads would be running, or which one I need to kill... How do I kill / restart the thin daemon?

Read the article
Unable to call through asterisk

- by sk

I want to create a voip service. I have installed asterisk-1.4 on a dedicated remotely hosted debian lenny distro. I made a sip.conf and extensions.conf so as to place a call between two sip phones(i am using xlite 3.0) installed in some other Windows PC. Whenever i switch this phones the asterisk console shows that Registration from '"1000"<sip:[email protected]>' failed for '122.168.10.254' - Peer is not supposed to register Where xx.xx.xx.xx is the server's IP. i.e my sip phones are unable to register with the asterisk server. Please help me to place call between two sip phones #sip show peers Name/username Host Dyn Nat ACL Port Status 2000 (Unspecified) D 0 Unmonitored 1000 (Unspecified) D 0 Unmonitored 2 sip peers [Monitored: 0 online, 0 offline Unmonitored: 0 online, 2 offline] # sip show registry Host Username Refresh State Reg.Time # sip show channels Peer User/ANR Call ID Seq (Tx/Rx) Format Hold Last Message 0 active SIP channels

Read the article
Good Free Backup Tool - with provisos

- by vaccano

I have seen some Backup Questions around. But they are not quite what I am looking for. I would like to have a back up of my entire hard drive (to an external drive). I would like it to be the kind that has a base backup then just backs up the changes since the last backup. I would like it to be able to have a fully restorable image of my hard drive (not just key files). Lastly I would like it to be free (or super cheap). (The above requirements are important, but I will have to drop them if they up the price as my boss will not pay for them.) I have a Solid State Hard Drive 250 GB backing up to a 1TB external hard drive using Windows XP.

Read the article
CentOS Client - Unable to Establish iSCSI connection with multiple interfaces on the initiator

- by slashdot

So after upgrading to CentOS 6.2, I am seemingly no longer able to login into my iSCSI targets. I have multiple interfaces on different subnets on the system, and I first thought that it had to do with the fact that I may not be binding correct interfaces, which seems to be the case when looking at netstat, as this is clearly wrong: [root]? netstat -na|grep .90 tcp 0 1 10.10.100.60:42354 10.10.8.90:3260 SYN_SENT tcp 0 1 10.10.100.60:40777 10.10.9.90:3260 SYN_SENT I then went ahead and disabled all but one interface, and so as a result netstat appears to be correct, but the issue with login remains. I am positive that the target never sees a packet, because I see nothing by SYN_SENT. I know the problem is on my client, because the target is servicing multiple systems, none of which are CentOS 6.2. At this point I am pretty confident that some things changed between CentOS 6.0/6.1 and 6.2. So, if anyone have any thoughts, or ran into this, I would very much like to hear your thoughts. [root]? iscsiadm --mode node --targetname iqn.2011-12.dom.homer:01:lab-centos-servers-00001 --portal 10.10.8.90:3260,2 --interface=sw-iscsi-0 --login Logging in to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260] (multiple) iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals [root]? netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.10.8.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2.7 10.10.9.0 0.0.0.0 255.255.255.0 U 0 0 0 eth3.7 10.10.100.0 0.0.0.0 255.255.252.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2.7 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth3.7 0.0.0.0 10.10.100.1 0.0.0.0 UG 0 0 0 eth0 Output of ip addr show for the two interfaces involved: [root]? for i in 2.7 3.7; do ip addr show eth$i; done 6: eth2.7@eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:8d brd ff:ff:ff:ff:ff:ff inet 10.10.8.60/24 brd 10.10.8.255 scope global eth2.7 inet6 fe80::20c:29ff:fe94:5b8d/64 scope link valid_lft forever preferred_lft forever 7: eth3.7@eth3: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP link/ether 00:0c:29:94:5b:97 brd ff:ff:ff:ff:ff:ff inet 10.10.9.60/24 brd 10.10.9.255 scope global eth3.7 inet6 fe80::20c:29ff:fe94:5b97/64 scope link valid_lft forever preferred_lft forever Update 01/06/2012: This issue is getting even more interesting by the day it seems. I went a few weeks back and grabbed a snapshot of this system from before upgrading to 6.2. I spun up a new system from the snapshot, and reconfigured interface info and host keys, as well as iSCSI initiator and iscsi interface info to match new MACs. Changed nothing else. Then, I attempted to connect to my targets, and no issues at all. I cannot say that this was unexpected. I then went ahead and compared sysctl settings from both systems and there were differences after the upgrade, but nothing seemingly relevant to iSCSI or IP that could contribute to this. I also noticed that by default now two sessions per connection were enabled after the upgrade, but I changed it back to 1 session in /etc/iscsi/iscsid.conf. On the problematic system we can see that source interface is seemingly wrong, but even when I disable the 10.10.100 interface, problems persist. So, while this may be relevant, I could not validate it for certain. Needless to say, further research is necessary. Something is clearly different between releases. Working system is on 6.1, and non-working is 6.2. ::Working System:: tcp 0 0 10.10.8.210:39566 10.10.8.90:3260 ESTABLISHED tcp 0 0 10.10.9.210:46518 10.10.9.90:3260 ESTABLISHED [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.210 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.210 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.210 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 ::Non-working System:: tcp 0 1 10.10.100.60:44737 10.10.9.90:3260 SYN_SENT tcp 0 1 10.10.100.60:55479 10.10.8.90:3260 SYN_SENT [root]? ip route show 10.10.8.0/24 dev eth2.6 proto kernel scope link src 10.10.8.60 10.10.9.0/24 dev eth3.7 proto kernel scope link src 10.10.9.60 10.10.100.0/22 dev eth0 proto kernel scope link src 10.10.100.60 169.254.0.0/16 dev eth0 scope link metric 1002 169.254.0.0/16 dev eth2.6 scope link metric 1006 169.254.0.0/16 dev eth3.7 scope link metric 1007 default via 10.10.100.1 dev eth0 And the result is still same: [root]? iscsiadm: Could not login to [iface: sw-iscsi-0, target: iqn.2011-12.dom.homer:01:lab-centos-servers-00001, portal: 10.10.8.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not login to [iface: sw-iscsi-1, target: iqn.2011-12.dom.homer:02:lab-centos-servers-00001, portal: 10.10.9.90,3260]. iscsiadm: initiator reported error (8 - connection timed out) iscsiadm: Could not log into all portals Update 01/08/2012: I believe I have been able to figure out the answer to my issue. It is quite obscure and I doubt this will happen to anyone else any time soon. It turns out that setting iface.iscsi_ifacename and iface.hwaddress in the interfaces configuration file is not legal. When one manually adds an iscsi target, such as below, all settings from the interface config file are copied into the node config file, that gets created by the below command. Result is parameters iface.iscsi_ifacename and iface.hwaddress together in the same config file. These parameters are seemingly mutually exclusive, which does not exactly make sense, or there is perhaps an oversight in the codepath. Perhaps I will investigate further. # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:01:lab-centos-servers-00001 -p 10.10.8.90,3260,2 -I sw-iscsi-0 # iscsiadm -m node --op new -T iqn.2011-12.dom.homer:02:lab-centos-servers-00001 -p 10.10.9.90,3260,2 -I sw-iscsi-1 Notice, below I commented out iface.hwaddress and iface.ipaddress, after which I re-added targets, with same command as above. All works just fine. [root]? cat * # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-0 iface.net_ifacename = eth2.6 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.8.60 iface.transport_name = tcp iface.vlan_id = 6 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD # BEGIN RECORD 2.0-872.33.el6 iface.iscsi_ifacename = sw-iscsi-1 iface.net_ifacename = eth3.7 #iface.hwaddress = XX:XX:XX:XX:XX:XX #iface.ipaddress = 10.10.9.60 iface.transport_name = tcp iface.vlan_id = 7 iface.vlan_priority = 0 iface.iface_num = 0 iface.mtu = 0 iface.port = 0 # END RECORD Again, chances of this happening to someone else are slim to none, so likely waste of time typing this up. But, if someone does encounter this issue, I hope this post will help.

Read the article
dead man's switch for remote networking interventions

- by ascobol

Hi, As I'm going to change the network configuration of a remote server, I was thinking of some security mechanisms to protect me from accidentally loosing control on the server. The level-0 protection I'm using is a scheduled system reboot: # at now+x minutes > reboot > ctrl+D where x is the delay before reboot. While this works relatevly well for very simple tasks like playing with iptables this method has at least two drawbacks: It's not very reactive, ie a connectivity problem should be detected automatically if for example an automatic remote ssh command fails does not work anymore for x seconds. It can obviously not work if one need to modify some configuration files and then reboot to test the changes. Are you guys using some tool for the second point ? I would love to have something able to revert the system configuration in a previously known stable state if I can't join the server X minutes after reboot. Thanks!

Read the article
Recommendations for screen-capture tool that retains menus and mouse pointer

- by Chris Farmer

There are several screen capture tool questions already on this site, but I think I have a slight tweak to the usual. I'd like a handy screen capture utility that can: Run in Windows 7 Capture a sub-region of the screen Show the current state of the mouse cursor and any active menus I'd like to use it for writing docs that refer to specific application menu items. I like the built-in snipping tool in Windows 7, but the act of using it dismisses my menus, and it doesn't get the mouse cursor either. Do any such tools exist? EDIT: Ahh, I wasn't familiar with the "delayed capture" options of these tools, but they all seem to fit the bill. Thanks!

Read the article
Tomcat IIS 7 Integration gives 503 errors on all requests.

- by Yvan JANSSENS

Hi, After many attempts to install Tomcat on IIS 7, I finally managed to get it working. At least I think so :-S. I finally got the 500 errors away, by setting the correct permissions. The only thing that doesn't work is ... serving stuff: neither regular stuff (like ASP, HTML files, or directory browsing) or Tomcat things work. Here are my configs: Worker.properties # The workers that your plugins should create and work with # worker.list=worker1 #------ DEFAULT ajp13 WORKER DEFINITION ------------------------------ #--------------------------------------------------------------------- # Defining a worker named ajp13 and of type ajp13 # Note that the name and the type do not have to match. # worker.worker1.port=8009 worker.worker1.host=127.0.0.1 worker.worker1.type=ajp13 URIWorkerMap.properties /|/*=worker1 # Exclude the subdirectory static: !/static|/*=worker1 # Exclude some suffixes: !*.html=worker1 !*.asp=worker1 Server.xml <?xml version='1.0' encoding='utf-8'?>   <Server port="8005" shutdown="SHUTDOWN">  <Listener className="org.apache.catalina.core.AprLifecycleListener" SSLEngine="on" />  <Listener className="org.apache.catalina.core.JasperListener" />  <Listener className="org.apache.catalina.core.JreMemoryLeakPreventionListener" />  <Listener className="org.apache.catalina.mbeans.ServerLifecycleListener" /> <Listener className="org.apache.catalina.mbeans.GlobalResourcesLifecycleListener" />  <GlobalNamingResources>  <Resource name="UserDatabase" auth="Container" type="org.apache.catalina.UserDatabase" description="User database that can be updated and saved" factory="org.apache.catalina.users.MemoryUserDatabaseFactory" pathname="conf/tomcat-users.xml" /> </GlobalNamingResources>  <Service name="Catalina">    <Connector port="8080" protocol="HTTP/1.1" connectionTimeout="20000" redirectPort="8443" />      <Connector port="8009" protocol="AJP/1.3" redirectPort="8443" />   <Engine name="Catalina" defaultHost="localhost">      <Realm className="org.apache.catalina.realm.UserDatabaseRealm" resourceName="UserDatabase"/>  <Host name="localhost" appBase="webapps" unpackWARs="true" autoDeploy="true" xmlValidation="false" xmlNamespaceAware="false">     </Host> </Engine> </Service> </Server> http://localhost:8080 is working, I can view the apps and configure them there... I'm quite new to IIS 7, I used to work with IIS 6. Thanks in advance, Yvan

Read the article
Server 2008 Web Edition IIS6 SMTP conflict

- by user219313

I'm using IIS6 Manager to setup the SMTP service on Windows Server 2008 Web Edition. There seems to be a conflict (port 25?) which means that I cannot start and stop the Default SMTP server within IIS6. I can start and stop it with the services.msc snap in and this is reflected in state of the SMTP server in IIS6 manager. I'm worried that none of the settings I want to get at within IIS6 (logging, authentication etc..) are having any effect. None of these settings are available within IIS7 in Web Edition.

Read the article
Disable "Windows Firewall with Advanced Security" for all profiles(Domain,Public,Standard) in local GP using script help! Windows 7 Clients

- by JoBo

We need Windows7 with windows firewall to be turned off , so the GOLD image has windows firewall turned off for all profiles(Domain,Public,Standard) and Windows Service disabled No the same GOLD image deployed with MDT (Apply local GPO) has enabled Windows Firewall under "Windows Firewall with Advanced Security" as part of task sequence Now we need to remove it. "These machines are now on Domain where in we have no rights/control on the domain level GPO", we have local admi rights on these machines We have a requirement do set the "Windows Firewall with Advanced Security" to "NOT Configured" or "OFF "on these machines In gpedit.msc if we manually go to "Windows Firewall with Advanced Security" after enabling Windows Firewall Services then can Clear the settings Do do the same manually on all machines is extra effort Changing values in registry will get reverted on machine restart as its getting applied from local GPO Also using GPMC can connect to remote computer and can manually or using wfw file we can make it not configured but we are looking for a script or a less effort method to accomplish this Please suggest NB: CIA has already reported similar issue//How do I turn off Windows 7 Firewall via script or through automation?// , but doing netsh advfirewall set allprofiles state off on already deployed machines did not make change (FW service on all machine is disabled in GOLd image)// Thanks and Regards Jose

Read the article
iPhone VPN with OpenSwan fails to reconnect

- by gilm

I have managed to configure VPN with iPhone and OpenSWAN on Linux 2.6. Though, when disconnecting the iphone and reconnecting, it times out. I have found that: 1) no packets are being sent when you disconnect iPhone from VPN. 2) when reconnecting, pluto picks up on the older socket and tries to use that state machine. which then fails and iPhone retransmits until times out. I'm using the latest version in git, including #1204 patch. I see the NAT-T patch debug lines in the logs. But still, no cookie. Help?

Read the article
Xen DomU on DRBD device: barrier errors

- by Halfgaar

I'm testing setting up a Xen DomU with a DRBD storage for easy failover. Most of the time, immediatly after booting the DomU, I get an IO error: [ 3.153370] EXT3-fs (xvda2): using internal journal [ 3.277115] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.336014] nf_conntrack version 0.5.0 (3899 buckets, 15596 max) [ 3.515604] init: failsafe main process (397) killed by TERM signal [ 3.801589] blkfront: barrier: write xvda2 op failed [ 3.801597] blkfront: xvda2: barrier or flush: disabled [ 3.801611] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801630] end_request: I/O error, dev xvda2, sector 52171168 [ 3.801642] Buffer I/O error on device xvda2, logical block 6521396 [ 3.801652] lost page write due to I/O error on xvda2 [ 3.801755] Aborting journal on device xvda2. [ 3.804415] EXT3-fs (xvda2): error: ext3_journal_start_sb: Detected aborted journal [ 3.804434] EXT3-fs (xvda2): error: remounting filesystem read-only [ 3.814754] journal commit I/O error [ 6.973831] init: udev-fallback-graphics main process (538) terminated with status 1 [ 6.992267] init: plymouth-splash main process (546) terminated with status 1 The manpage of drbdsetup says that LVM (which I use) doesn't support barriers (better known as tagged command queuing or native command queing), so I configured the drbd device not to use barriers. This can be seen in /proc/drbd (by "wo:f, meaning flush, the next method drbd chooses after barrier): 3: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r---- ns:2160152 nr:520204 dw:2680344 dr:2678107 al:3549 bm:9183 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 And on the other host: 3: cs:Connected ro:Secondary/Primary ds:UpToDate/UpToDate C r---- ns:0 nr:2160152 dw:2160152 dr:0 al:0 bm:8052 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 I also enabled the option disable_sendpage, as per the drbd docs: cat /sys/module/drbd/parameters/disable_sendpage Y I also tried adding barriers=0 to fstab as mount option. Still it sometimes says: [ 58.603896] blkfront: barrier: write xvda2 op failed [ 58.603903] blkfront: xvda2: barrier or flush: disabled I don't even know if ext3 has a nobarrier option. And, because only one of my storage systems is battery backed, it would not be smart anyway. Why does it still compain about barriers when I disabled that? Both host are: Debian: 6.0.4 uname -a: Linux 2.6.32-5-xen-amd64 drbd: 8.3.7 Xen: 4.0.1 Guest: Ubuntu 12.04 LTS uname -a: Linux 3.2.0-24-generic pvops drbd resource: resource drbdvm { meta-disk internal; device /dev/drbd3; startup { # The timeout value when the last known state of the other side was available. 0 means infinite. wfc-timeout 0; # Timeout value when the last known state was disconnected. 0 means infinite. degr-wfc-timeout 180; } syncer { # This is recommended only for low-bandwidth lines, to only send those # blocks which really have changed. #csums-alg md5; # Set to about half your net speed rate 60M; # It seems that this option moved to the 'net' section in drbd 8.4. (later release than Debian has currently) verify-alg md5; } net { # The manpage says this is recommended only in pre-production (because of its performance), to determine # if your LAN card has a TCP checksum offloading bug. #data-integrity-alg md5; } disk { # Detach causes the device to work over-the-network-only after the # underlying disk fails. Detach is not default for historical reasons, but is # recommended by the docs. # However, the Debian defaults in drbd.conf suggest the machine will reboot in that event... on-io-error detach; # LVM doesn't support barriers, so disabling it. It will revert to flush. Check wo: in /proc/drbd. If you don't disable it, you get IO errors. no-disk-barrier; } on host1 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.1:7792; } on host2 { # universe is a VG disk /dev/universe/drbdvm-disk; address 10.0.0.2:7792; } } DomU cfg: bootloader = '/usr/lib/xen-default/bin/pygrub' vcpus = '2' memory = '512' # # Disk device(s). # root = '/dev/xvda2 ro' disk = [ 'phy:/dev/drbd3,xvda2,w', 'phy:/dev/universe/drbdvm-swap,xvda1,w', ] # # Hostname # name = 'drbdvm' # # Networking # # fake IP for posting vif = [ 'ip=1.2.3.4,mac=00:16:3E:22:A8:A7' ] # # Behaviour # on_poweroff = 'destroy' on_reboot = 'restart' on_crash = 'restart' In my test setup: the primary host's storage is 9650SE SATA-II RAID PCIe with battery. The secondary is software RAID1. Isn't DRBD+Xen widely used? With these problems, it's not going to work.

Read the article
Windows 7 - cancel mirror synchronisation

- by Chris W

I've got basic disk OS managed disk mirroring setup in Windows 7 for a couple of volumes. After a power failure the mirrors are currently resynching. These are only small volumes of data but the sync has not completed after more than 24 hours. Is there any way to stop this as it's driving me nuts? I need to get the machine back to a usable state to get some work done but it's a bit of a dog whilst this synch is going on. I've tried removing the mirrors but it won't let me do that whilst the re-sync is in progress.

Read the article
Windows 7 - cancel mirror synchronisation

- by Chris W

I've got basic disk OS managed disk mirroring setup in Windows 7 for a couple of volumes. After a power failure the mirrors are currently resynching. These are only small volumes of data but the sync has not completed after more than 24 hours. Is there any way to stop this as it's driving me nuts? I need to get the machine back to a usable state to get some work done but it's a bit of a dog whilst this synch is going on. I've tried removing the mirrors but it won't let me do that whilst the re-sync is in progress.

Read the article
How can I free up disk space in my Ubuntu Hardy Heron install?

- by rvs

I'd like to make some room on /dev/sda1 without necessarily having to remove a whole bunch of applications (I've already gone through and deleted all frivolous apps). This is the state of /dev/sda1 currently: Dir: / Type: ext3 Total: 9.4GiB Free: 488.6MiB Available: 0bytes Used: 8.9GiB EDIT added du output from comments below: 769068 /var/lib/mysql 351208 /usr/lib 297060 /usr/local/bin/eclipse/plugins 184124 /usr/bin 175924 /usr/lib/openoffice/program 143940 /usr/local/bin/eclipsePHP/plugins 92520 /boot 81200 /opt/android-sdk-linux/add-ons/google_apis-6_r01/images 79964 /opt That's funny, because the tables in /var/lib/mysql are the reason that I ran out in the first place. But I need them, and room for many more possibly large db's.

Read the article
Exim 4.63 on CentOS: sending mail from server app through localhost - failed on authentication

- by Stas

Hi! I am trying to send mail from my java application simply connecting on localhost:25 with empty login and password (I have to state them due to API). Mail sending is failed then with 2010-03-21 12:20:01 login authenticator failed for localhost [127.0.0.1]: 535 Incorrect authentication data On the other hand, when I am sending mail with telnet by: $ telnet localhost 25 ehlo ... mail from:... rcpt to:... data: ... it works perfectly. Any clues?

Read the article
Connecting HDMI MediaCenter PC to Standard Def TV

- by Adam

I just purchased a ASRock ION 330-HT-BD to use as my new Media Center. Sadly I still have a crappy standard-def old tube TV for the foreseeable future. The TV has Coax & Composite (Red, White, Yellow) inputs, and my new MediaCenterr has HDMI & VGA outputs. So my question is, how do I hook up the two together! All of the HDMI-to-Composite cables I have found explicitly state that they can not be used to hook a PC up to a TV. Any ideas?

Read the article

< Previous Page | 347 348 349 350 351 352 353 354 355 356 357 358 | Next Page >