Search Results

Search found 9278 results on 372 pages for 'generic handler'.

Page 352/372 | < Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >

• Computer won't reboot without waiting for a while

  - by Benjamin

  I've got an unusual problem with my computer. When ever I reboot my computer it won't boot, I get a few beeps from the BIOS and nothing else, however if I wait for a few minuets the computer will boot perfectly. I tried to count the beeps and I get around 7-9 of them; the first two are noticeably closer together than the rest. [Edit: I'm now reasonably confident it's 1 long followed by 8 short beeps. That would be a display related issue: http://www.bioscentral.com/beepcodes/amibeep.htm] My BIOS is American Megatrends Inc and version P1.80, the Motherboard is an ASRock X58 Extreme (both according to dmidecode) Here's an output from LSPCI, I'm not sure what else might be useful but I can provide whatever's asked. 00:00.0 Host bridge: Intel Corporation 5520/5500/X58 I/O Hub to ESI Port (rev 13) 00:01.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 1 (rev 13) 00:03.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 3 (rev 13) 00:07.0 PCI bridge: Intel Corporation 5520/5500/X58 I/O Hub PCI Express Root Port 7 (rev 13) 00:14.0 PIC: Intel Corporation 5520/5500/X58 I/O Hub System Management Registers (rev 13) 00:14.1 PIC: Intel Corporation 5520/5500/X58 I/O Hub GPIO and Scratch Pad Registers (rev 13) 00:14.2 PIC: Intel Corporation 5520/5500/X58 I/O Hub Control Status and RAS Registers (rev 13) 00:14.3 PIC: Intel Corporation 5520/5500/X58 I/O Hub Throttle Registers (rev 13) 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 SATA controller: Intel Corporation 82801JI (ICH10 Family) SATA AHCI Controller 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03) 02:00.0 FireWire (IEEE 1394): VIA Technologies, Inc. VT6315 Series Firewire Controller 02:00.1 IDE interface: VIA Technologies, Inc. VT6415 PATA IDE Host Controller (rev a0) 03:00.0 SATA controller: JMicron Technology Corp. JMB360 AHCI Controller (rev 02) 05:00.0 VGA compatible controller: nVidia Corporation GT200b [GeForce GTX 285] (rev a1) ff:00.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture Generic Non-Core Registers (rev 05) ff:00.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QuickPath Architecture System Address Decoder (rev 05) ff:02.0 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Link 0 (rev 05) ff:02.1 Host bridge: Intel Corporation Xeon 5500/Core i7 QPI Physical 0 (rev 05) ff:03.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller (rev 05) ff:03.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Target Address Decoder (rev 05) ff:03.4 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Test Registers (rev 05) ff:04.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Control Registers (rev 05) ff:04.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Address Registers (rev 05) ff:04.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Rank Registers (rev 05) ff:04.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 0 Thermal Control Registers (rev 05) ff:05.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Control Registers (rev 05) ff:05.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Address Registers (rev 05) ff:05.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Rank Registers (rev 05) ff:05.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 1 Thermal Control Registers (rev 05) ff:06.0 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Control Registers (rev 05) ff:06.1 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Address Registers (rev 05) ff:06.2 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Rank Registers (rev 05) ff:06.3 Host bridge: Intel Corporation Xeon 5500/Core i7 Integrated Memory Controller Channel 2 Thermal Control Registers (rev 05) Update: ok I installed lm-sensors and here's the output. coretemp-isa-0000 Adapter: ISA adapter Core 0: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 1: +59.0°C (high = +80.0°C, crit = +100.0°C) Core 2: +58.0°C (high = +80.0°C, crit = +100.0°C) Core 3: +57.0°C (high = +80.0°C, crit = +100.0°C) it8720-isa-0a10 Adapter: ISA adapter in0: +0.93 V (min = +0.00 V, max = +4.08 V) in1: +0.06 V (min = +0.00 V, max = +4.08 V) in2: +3.25 V (min = +0.00 V, max = +4.08 V) +5V: +2.91 V (min = +0.00 V, max = +4.08 V) in4: +3.04 V (min = +0.00 V, max = +4.08 V) in5: +2.94 V (min = +0.00 V, max = +4.08 V) in6: +2.14 V (min = +0.00 V, max = +4.08 V) 5VSB: +2.96 V (min = +0.00 V, max = +4.08 V) Vbat: +3.28 V fan1: 1869 RPM (min = 0 RPM) fan2: 0 RPM (min = 0 RPM) fan3: 0 RPM (min = 0 RPM) fan4: 1106 RPM (min = -1 RPM) fan5: 225000 RPM (min = -1 RPM) temp1: +39.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp2: +56.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor temp3: +127.0°C (low = +0.0°C, high = +127.0°C) sensor = thermistor cpu0_vid: +1.650 V intrusion0: ALARM If it helps here's the summery from sensors-detect Driver `it87': * ISA bus, address 0xa10 Chip `ITE IT8720F Super IO Sensors' (confidence: 9) Driver `adt7475': * Bus `NVIDIA i2c adapter 3 at 5:00.0' Busdriver `nvidia', I2C address 0x2e Chip `Analog Devices ADT7473' (confidence: 5) Driver `coretemp': * Chip `Intel digital thermal sensor' (confidence: 9)

  Read the article

• Using LINQ to create a simple login

  - by JDWebs

  I'm an C# ASP.NET beginner, so please excuse anything that's... not quite right! In short, I want to create a really basic login system: one which runs through a database and uses sessions so that only logged in users can access certain pages. I know how to do most of that, but I'm stuck with querying data with LINQ on the login page. On the login page, I have a DropDownList to select a username, a Textbox to type in a password and a button to login (I also have a literal for errors). The DropDownList is databound to a datatable called DT_Test. DT_Test contains three columns: UsernameID (int), Username (nchar(30)) and Password (nchar(30)). UsernameID is the primary key. I want to make the button's click event query data from the database with the DropDownList and Textbox, in order to check if the username and password match. But I don't know how to do this... Current Code (not a lot!): Front End: <%@ Page Language="C#" AutoEventWireup="true" CodeFile="Login_Test.aspx.cs" Inherits="Login_Login_Test" %> <!DOCTYPE html PUBLIC "-//W3C//DTD XHTML 1.0 Transitional//EN" "http://www.w3.org/TR/xhtml1/DTD/xhtml1-transitional.dtd"> <html xmlns="http://www.w3.org/1999/xhtml"> <head runat="server"> <title>Login Test</title> </head> <body> <form id="LoginTest" runat="server"> <div> <asp:DropDownList ID="DDL_Username" runat="server" Height="20px" DataTextField="txt"> </asp:DropDownList> <br /> <asp:TextBox ID="TB_Password" runat="server" TextMode="Password"></asp:TextBox> <br /> <asp:Button ID="B_Login" runat="server" onclick="B_Login_Click" Text="Login" /> <br /> <asp:Literal ID="LI_Result" runat="server"></asp:Literal> </div> </form> </body> </html> Back End: using System; using System.Collections.Generic; using System.Linq; using System.Web; using System.Web.UI; using System.Web.UI.WebControls; public partial class Login_Login_Test : System.Web.UI.Page { protected void Page_Load(object sender, EventArgs e) { if (!Page.IsPostBack) { Binder(); } } private void Binder() { using (DataClassesDataContext db = new DataClassesDataContext()) { DDL_Username.DataSource = from x in db.DT_Honeys select new { x.UsernameID, txt = x.Username }; DDL_Username.DataBind(); } } protected void B_Login_Click(object sender, EventArgs e) { if (TB_Password.Text != "") { using (DataClassesDataContext db = new DataClassesDataContext()) { } } } } I have spent hours searching and trying different code, but none of it seems to fit in for this context. Anyway, help and tips appreciated, thank you very much! I am aware of security risks etc. but this is not a live website or anything, it is simply for testing purposes as a beginner. *

  Read the article

• Anything wrong with this function for comparing floats?

  - by Michael Borgwardt

  When my Floating-Point Guide was yesterday published on slashdot, I got a lot of flak for my suggested comparison function, which was indeed inadequate. So I finally did the sensible thing and wrote a test suite to see whether I could get them all to pass. Here is my result so far. And I wonder if this is really as good as one can get with a generic (i.e. not application specific) float comparison function, or whether I still missed some edge cases. import static org.junit.Assert.assertFalse; import static org.junit.Assert.assertTrue; import org.junit.Test; public class NearlyEqualsTest { public static boolean nearlyEqual(float a, float b) { final float epsilon = 0.000001f; final float absA = Math.abs(a); final float absB = Math.abs(b); final float diff = Math.abs(a-b); if (a*b==0) { // a or b or both are zero // relative error is not meaningful here return diff < Float.MIN_VALUE / epsilon; } else { // use relative error return diff / (absA+absB) < epsilon; } } /** Regular large numbers - generally not problematic */ @Test public void big() { assertTrue(nearlyEqual(1000000f, 1000001f)); assertTrue(nearlyEqual(1000001f, 1000000f)); assertFalse(nearlyEqual(10000f, 10001f)); assertFalse(nearlyEqual(10001f, 10000f)); } /** Negative large numbers */ @Test public void bigNeg() { assertTrue(nearlyEqual(-1000000f, -1000001f)); assertTrue(nearlyEqual(-1000001f, -1000000f)); assertFalse(nearlyEqual(-10000f, -10001f)); assertFalse(nearlyEqual(-10001f, -10000f)); } /** Numbers around 1 */ @Test public void mid() { assertTrue(nearlyEqual(1.0000001f, 1.0000002f)); assertTrue(nearlyEqual(1.0000002f, 1.0000001f)); assertFalse(nearlyEqual(1.0002f, 1.0001f)); assertFalse(nearlyEqual(1.0001f, 1.0002f)); } /** Numbers around -1 */ @Test public void midNeg() { assertTrue(nearlyEqual(-1.000001f, -1.000002f)); assertTrue(nearlyEqual(-1.000002f, -1.000001f)); assertFalse(nearlyEqual(-1.0001f, -1.0002f)); assertFalse(nearlyEqual(-1.0002f, -1.0001f)); } /** Numbers between 1 and 0 */ @Test public void small() { assertTrue(nearlyEqual(0.000000001000001f, 0.000000001000002f)); assertTrue(nearlyEqual(0.000000001000002f, 0.000000001000001f)); assertFalse(nearlyEqual(0.000000000001002f, 0.000000000001001f)); assertFalse(nearlyEqual(0.000000000001001f, 0.000000000001002f)); } /** Numbers between -1 and 0 */ @Test public void smallNeg() { assertTrue(nearlyEqual(-0.000000001000001f, -0.000000001000002f)); assertTrue(nearlyEqual(-0.000000001000002f, -0.000000001000001f)); assertFalse(nearlyEqual(-0.000000000001002f, -0.000000000001001f)); assertFalse(nearlyEqual(-0.000000000001001f, -0.000000000001002f)); } /** Comparisons involving zero */ @Test public void zero() { assertTrue(nearlyEqual(0.0f, 0.0f)); assertFalse(nearlyEqual(0.00000001f, 0.0f)); assertFalse(nearlyEqual(0.0f, 0.00000001f)); } /** Comparisons of numbers on opposite sides of 0 */ @Test public void opposite() { assertFalse(nearlyEqual(1.000000001f, -1.0f)); assertFalse(nearlyEqual(-1.0f, 1.000000001f)); assertFalse(nearlyEqual(-1.000000001f, 1.0f)); assertFalse(nearlyEqual(1.0f, -1.000000001f)); assertTrue(nearlyEqual(10000f*Float.MIN_VALUE, -10000f*Float.MIN_VALUE)); } /** * The really tricky part - comparisons of numbers * very close to zero. */ @Test public void ulp() { assertTrue(nearlyEqual(Float.MIN_VALUE, -Float.MIN_VALUE)); assertTrue(nearlyEqual(-Float.MIN_VALUE, Float.MIN_VALUE)); assertTrue(nearlyEqual(Float.MIN_VALUE, 0)); assertTrue(nearlyEqual(0, Float.MIN_VALUE)); assertTrue(nearlyEqual(-Float.MIN_VALUE, 0)); assertTrue(nearlyEqual(0, -Float.MIN_VALUE)); assertFalse(nearlyEqual(0.000000001f, -Float.MIN_VALUE)); assertFalse(nearlyEqual(0.000000001f, Float.MIN_VALUE)); assertFalse(nearlyEqual(Float.MIN_VALUE, 0.000000001f)); assertFalse(nearlyEqual(-Float.MIN_VALUE, 0.000000001f)); assertFalse(nearlyEqual(1e20f*Float.MIN_VALUE, 0.0f)); assertFalse(nearlyEqual(0.0f, 1e20f*Float.MIN_VALUE)); assertFalse(nearlyEqual(1e20f*Float.MIN_VALUE, -1e20f*Float.MIN_VALUE)); } }

  Read the article

• Are there supposed to be more restrictions on operator->* overloads?

  - by Potatoswatter

  I was perusing section 13.5 after refuting the notion that built-in operators do not participate in overload resolution, and noticed that there is no section on operator->*. It is just a generic binary operator. Its brethren, operator->, operator*, and operator[], are all required to be non-static member functions. This precludes definition of a free function overload to an operator commonly used to obtain a reference from an object. But the uncommon operator->* is left out. In particular, operator[] has many similarities. It is binary (they missed a golden opportunity to make it n-ary), and it accepts some kind of container on the left and some kind of locator on the right. Its special-rules section, 13.5.5, doesn't seem to have any actual effect except to outlaw free functions. (And that restriction even precludes support for commutativity!) So, for example, this is perfectly legal (in C++0x, remove obvious stuff to translate to C++03): #include <utility> #include <iostream> #include <type_traits> using namespace std; template< class F, class S > typename common_type< F,S >::type operator->*( pair<F,S> const &l, bool r ) { return r? l.second : l.first; } template< class T > T & operator->*( pair<T,T> &l, bool r ) { return r? l.second : l.first; } template< class T > T & operator->*( bool l, pair<T,T> &r ) { return l? r.second : r.first; } int main() { auto x = make_pair( 1, 2.3 ); cerr << x->*false << " " << x->*4 << endl; auto y = make_pair( 5, 6 ); y->*(0) = 7; y->*0->*y = 8; // evaluates to 7->*y = y.second cerr << y.first << " " << y.second << endl; } I can certainly imagine myself giving into temp[la]tation. For example, scaled indexes for vector: v->*matrix_width[5] = x; Did the standards committee forget to prevent this, was it considered too ugly to bother, or are there real-world use cases?

  Read the article

• Survey Data Model - How to avoid EAV and excessive denormalization?

  - by AlexDPC

  Hi everyone, My database skills are mediocre at best and I have to design a data model for survey data. I have spent some thoughts on this and right now I feel that I am stuck between some kind of EAV model and a design involving hundreds of tables, each with hundreds of columns (and thousands of records). There must be a better way to do this and I hope that the wise folks on this forum can help me. I have already searched various forums, but I couldn't really find a solution. If it has already been given elsewhere, please excuse me and provide me with a link so I can read it up. Some assumptions about the data I have to deal with: Each survey consists of 1 to n questionnaires Each questionnaire consists of 100-2,000 questions (please ignore that 2,000 questions really sound like a lot to answer...) Questions can be of various types: multiple-choice, free text, a number (like age, income, percentages, ...) Each survey involves 10-200 countries (These are not the respondents. The respondents are actually people in the countries.) Depending on the type of questionnaire, each questionnaire is answered by 100-20,000 respondents per country. A country can adapt the questionnaires for a survey, i.e. add, remove or edit questions The data for one country is gathered in a separate database in that country. There is no possibility for online integration from the start. The data for all countries has to be integrated later. This means for example, if a country has deleted a question, that data must somehow be derived from what they sent in order to achieve a uniform design across all countries I will have to write the integration and cleaning software, which will need to work with every country's data In the end the data needs to be exported to flat files, one rectangular grid per country and questionnaire. I have already discussed this topic with people from various backgrounds and have not come to a good solution yet. I mainly got two kinds of opinions. The domain experts, who are used to working with flat files (spreadsheet-style) for data processing and analysis vote for a denormalized structure with loads of tables and columns as I described above (1 table per country and questionnaire). This sounds terrible to me, because I learned that wide tables are to be avoided, it will be annoying to determine which columns are actually in a table when working with it, the database will become cluttered with hundreds of tables (or I even need to set up multiple databases, each with a similar yet a bit differetn design), etc. O-O-programmers vote for a strongly "normalized" design, which would effectively lead to a central table containing all the answers from all respondents to all questions. This table would either need to contain a column of type sql_variant type or multiple answer columns with different types to store answers of different types (multiple choice, free text, ..). The former would essentially be a EAV model. I tend to follow Joe Celko here, who strongly discourages its use (he calls it OTLT or "One True Lookup Table"). The latter would imply that each row would contain null cells for the not applicable types by design. Another alternative I could think of would be to create one table per answer type, i.e., one for multiple-choice questions, one for free text questions, etc.. That's not so generic, it would lead to a lot of union joins, I think and I would have to add a table if a new answer type is invented. Sorry for boring you with all this text and thank you for your input! Cheers, Alex PS: I asked the same question here: http://www.eggheadcafe.com/community/aspnet/13/10242616/survey-data-model--how-to-avoid-eav-and-excessive-denormalization.aspx

  Read the article

• Facebook iFrame APP not working in IE, works on every other browser

  - by Sean Ashmore

  So im getting a blank page when loading this page within an iFrame on Internet explorer, every other browser works fine.. I have also tried using p3p headers as other people have suggested, but to no avail. <?php require ("connect.php"); require ("config.php"); require ("fb_config.php"); ?> <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01//EN" "http://www.w3.org/TR/html4/strict.dtd"> <html> <head> <title>Login handler</title> <meta http-equiv="content-type" content="text/html; charset=iso-8859-1"> <link rel="stylesheet" href="css/login.css" type="text/css"> </head> <body> <?//=$user?> <?php if($user == 0) { echo "You are not logged into facebook. Nice try."; }else{ $query = "SELECT id,fb_id,login_ip,login_count,activated,sitestate FROM login WHERE fb_id='".mysql_real_escape_string($user)."'"; $result = mysql_query($query) or die(mysql_error()); $row = mysql_fetch_array($result); if (mysql_num_rows($result) == 0) { $sql = "INSERT INTO login SET id = '', fb_id ='" .mysql_real_escape_string($user). "', name = '" .rand(10000000000000000,99999999999999999999). "', signup =NOW() , password = '" .mysql_real_escape_string($pass). "', state = '0', mail = '" .mysql_real_escape_string($_POST['mail']). "',location='".mysql_real_escape_string($randomlocation)."',location_start='".mysql_real_escape_string($randomlocation)."', signup_ip='".mysql_real_escape_string($_SERVER['REMOTE_ADDR'])."',ref='".mysql_real_escape_string($_POST['ref'])."', activation_id = '" .mysql_real_escape_string($activation_link). "',activated='2', killprotection = '$twodayprot',gender='" .mysql_real_escape_string($_POST["gender"]). "'"; $res = mysql_query($sql); } //if($row['fb_id'] != $user){ //echo "Your facebook ID: $user is NOT in the MW DB."; //exit(); //}else{ if(empty($row['login_ip'])){ $row['login_ip'] = $_SERVER['REMOTE_ADDR']; }else{ $ip_information = explode("-", $row['login_ip']); if (in_array($_SERVER['REMOTE_ADDR'], $ip_information)) { $row['login_ip'] = $row['login_ip']; }else{ $row['login_ip'] = $row['login_ip']."-".$_SERVER['REMOTE_ADDR']; } } $update_login = mysql_query("UPDATE login SET login_count=login_count+'1' WHERE name='".mysql_real_escape_string($_POST['username'])."'") or die(mysql_error()); $_SESSION['user_id'] = $row['id']; $result = mysql_query("UPDATE login SET userip='".mysql_real_escape_string($_SERVER['REMOTE_ADDR'])."',login_ip='".mysql_real_escape_string($row['login_ip'])."',login_count='0' WHERE id='".mysql_real_escape_string($_SESSION['user_id'])."'") or die(mysql_error()); if ($row['sitestate'] == 0){ header("location: home.php"); } elseif ($row['sitestate'] == 2) { header("location: killed.php?id={$row['id']}&encrypted={$row['password']}"); } else { header("location: banned.php?id={$row['id']}&encrypted={$row['password']}"); } }// id check. ?> </body> </html>

  Read the article

• Regarding Sqlite Datbase connectivity in iphone

  - by Prash.......

  hi.. I am developing an application in iphone in which i have to do the database connectivity using sqlite. I have made a "clsDBManage" class which contains 4 functions open_database, close_database, is_database_open, getdatabase_connection, which are globally defined ,i have a screen called "user details" in which i am filling the user details such as name , mobileno , email-id , password, i want that when user feeds the info it should get connected with database and store the details entered and should authenticate the user the next time he logs in. (Just as we have yahoo login,gmail login screen) clsDBManage.h +(int) openDBConnection; +(int) closeDBConnection; +(BOOL) IsDatabaseOpen; +(sqlite3 *)getDBConnection; clsDBManage.m import "clsDBManage.h" import "Types.h" sqlite3 *DBConnection=nil; @implementation clsDBManage +(int) openDBConnection { NSArray *paths = NSSearchPathForDirectoriesInDomains(NSDocumentDirectory, NSUserDomainMask, YES); NSString *documentsDirectory = [paths objectAtIndex:0]; NSString *path = [documentsDirectory stringByAppendingPathComponent:@"iphone.sqlite"]; //Before if ([self IsDatabaseOpen] == YES) [self closeDBConnection]; // Open the database. The database was prepared outside the application. if (sqlite3_open([path UTF8String], &DBConnection ) == SQLITE_OK) { ifdef _DEBUG NSLog(@"Database Successfully Opened :)"); endif return CON_RET_SUCCESSFUL; } else { ifdef _DEBUG NSLog(@"Error in opening database :("); endif return CON_RET_ERROR; } } +(BOOL) IsDatabaseOpen { if(DBConnection != nil) { //add if condition to check database is in open state or close state return YES; } else { return NO; } } +(int) closeDBConnection { @try { if(DBConnection != nil) { sqlite3_close(DBConnection); DBConnection = nil; return CON_RET_SUCCESSFUL; } else { return CON_RET_ERROR; } } @catch (NSException * e) { NSLog([e reason]); } } +(sqlite3 *)getDBConnection { if ([self openDBConnection] == 1) return DBConnection; else return nil; } @end //classDBManage file is my handler class where i have written code to open database //my addprofile functions -(NSInteger)addProfile:(NSString *)mobileno:(NSString *)country:(NSString *)username:(NSString *)screenname:(NSString *)emailid:(NSString *)password:(NSString *)retypepassword { @try { sqlite3 *db =[clsDBManage getDBConnection]; if (db != nil) { sqlite3_stmt *statement =nil; const char *sql = "insert into SPCaccountdetails(MobileNo , Country , UserName , ScreenName, EmailId, Password, RetypePawssword) Values(?,?,?,?,?,?,?)"; if(sqlite3_prepare_v2(db, sql, -1, &statement, NULL) != SQLITE_OK) { //NSAssert1(0, @"Error while creating add statement. '%s'", sqlite3_errmsg(db)); } sqlite3_bind_text(statement, 1, [mobileno UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 2, [country UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 3, [username UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 4, [screenname UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 5, [emailid UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 6, [password UTF8String], -1, SQLITE_TRANSIENT); sqlite3_bind_text(statement, 7, [retypepassword UTF8String], -1, SQLITE_TRANSIENT); if(SQLITE_DONE != sqlite3_step(statement)) { NSAssert1(0, @"Error while inserting data. '%s'", sqlite3_errmsg(db)); } sqlite3_finalize(statement); } } @catch(NSException *e) { //[clsMessageBox ShowMessageOK:@CON_MESSAGE_TITLE_MESSAGE_USER_PROFILE :[e reason]]; } return CON_RET_SUCCESSFUL; } //button click event where i am calling addprofile function;_ [self addProfile:txtMobile :txtCountry :txtName :txtScreenname :txtemailid :txtpassword :txtretypepassword];

  Read the article

• How to make Net::Msmgr run?

  - by codeholic

  There's Net::Msmgr module on CPAN. It's written clean and the code looks trustworthy at the first glance. However this module seems to be beta and there is little documentation and no tests :-/ Has anyone used this module in production? I haven't managed to make it run by now, because it requires all event loop processing to be done in the application and as I've already said there is little documentation and no working examples to study. That's where I've gone so far: #!/usr/bin/perl use strict; use warnings; use Event; use Net::Msmgr::Object; use Net::Msmgr::Session; use Net::Msmgr::User; use constant DEBUG => 511; use constant EVENT_TIMEOUT => 5; # seconds my ($username, $password) = qw/[email protected] my.password/; my $buddy = '[email protected]'; my $user = Net::Msmgr::User->new(user => $username, password => $password); my $session = Net::Msmgr::Session->new; $session->debug(DEBUG); $session->login_handler(\&login_handler); $session->user($user); my $conv; sub login_handler { my $self = shift; print "LOGIN\n"; $self->ui_state_nln; $conv = $session->ui_new_conversation; $conv->invite($buddy); } our %watcher; sub ConnectHandler { my ($connection) = @_; warn "CONNECT\n"; my $socket = $connection->socket; $watcher{$connection} = Event->io(fd => $socket, cb => [ $connection, '_recv_message' ], poll => 're', desc => 'recv_watcher', repeat => 1); } sub DisconnectHandler { my $connection = shift; print "DISCONNECT\n"; $watcher{$connection}->cancel; } $session->connect_handler(\&ConnectHandler); $session->disconnect_handler(\&DisconnectHandler); $session->Login; Event::loop(); That's what it outputs: Dispatch Server connecting to: messenger.hotmail.com:1863 Dispatch Server connected CONNECT Dispatch Server >>>VER 1 MSNP2 CVR0 --> VER 1 MSNP2 CVR0 Dispatch Server >>>USR 2 MD5 I [email protected] --> USR 2 MD5 I [email protected] Dispatch Server <<<VER 1 CVR0 <-- VER 1 CVR0 And that's all, here it hangs. The handler on login is not being triggered. What am I doing wrong?

  Read the article

• Inconsistent accessibility

  - by user1312412

  I am getting the following error Inconsistent accessibility: parameter type 'Db.Form1.ConnectionString' is less accessible than method 'Db.Form1.BuildConnectionString(Db.Form1.ConnectionString)' //Name spaces using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Linq; using System.Text; using System.Windows.Forms; using Microsoft.VisualBasic; using System.Collections; using System.Diagnostics; using System.Data.OleDb; using System.IO; using System.Drawing.Printing; // namespace Db { public partial class Form1 : Form { public Form1() { InitializeComponent(); } public void SetBusy() { this.Cursor = Cursors.WaitCursor; Application.DoEvents(); } public void SetFree() { this.Cursor = Cursors.Default; Application.DoEvents(); } //connection string into parts struct ConnectionString { public string Provider; public string DataSource; public string UserId; public string Password; public string Database; } //Declare public string BuildConnectionString(ConnectionString connStr) ------> getting error here { string[] parts = new string[5]; parts[0] = "Provider=" + connStr.Provider; parts[1] = "Data Source=" + connStr.DataSource; parts[2] = "User Id=" + connStr.UserId; parts[3] = "Password=" + connStr.Password; parts[4] = "Initial Catalog=" + connStr.Database; return string.Join(";", parts); } // settings public bool IsValidConnectionForPrinting() { SetBusy(); ConnectionString connStr = new ConnectionString(); connStr.Provider = cboProvider.Text; connStr.DataSource = cboDataSource.Text; connStr.UserId = txtUserId.Text; connStr.Password = txtPassword.Text; connStr.Database = cboDatabase.Text; //connection string to database string connectionString = BuildConnectionString(connStr); OleDbConnection conn = new OleDbConnection(connectionString); try { conn.Open(); OleDbCommand cmd = conn.CreateCommand; cmd.CommandType = CommandType.TableDirect; cmd.CommandText = "vw_pr_DL"; cmd.ExecuteScalar(); cmd.CommandText = "vw_pr_VR"; cmd.ExecuteScalar(); //cmd.CommandText = "vw_pr_VR" //cmd.ExecuteScalar() conn.Close(); } //Exception messages catch (Exception ex) { SetFree(); if (ex.Message.StartsWith("Invalid object name")) { MessageBox.Show(ex.Message.Replace("Invalid object name", "Table or view not found"), "Connection Test"); } else { MessageBox.Show(ex.GetBaseException().Message, "Connection Test"); } return false; } SetFree(); return true; } // when user click testbutton private void btnConnTest_Click(object sender, EventArgs e) { if (IsValidConnectionForPrinting()) { MessageBox.Show("Connection succeeded", "Connection Test"); } }

  Read the article

• MySQL: How do I combine a Stored procedure with another Function?

  - by Laxmidi

  Hi I need some help in combining a stored procedure with another function. I've got a stored procedure that pulls latitudes and longitudes from a database. I've got another function that checks whether a point is inside a polygon. My goal is to combine the two functions, so that I can check whether the latitude and longitude points pulled from the db are inside a specific area. This stored procedure pulls latitude and longitudes from the database based on offense: DROP PROCEDURE IF EXISTS latlongGrabber; DELIMITER $$ CREATE PROCEDURE latlongGrabber(IN offense_in VARCHAR(255)) BEGIN DECLARE latitude_val VARCHAR(255); DECLARE longitude_val VARCHAR(255); DECLARE no_more_rows BOOLEAN; DECLARE latlongGrabber_cur CURSOR FOR SELECT latitude, longitude FROM myTable WHERE offense = offense_in; DECLARE CONTINUE HANDLER FOR NOT FOUND SET no_more_rows = TRUE; OPEN latlongGrabber_cur; the_loop: LOOP FETCH latlongGrabber_cur INTO latitude_val, longitude_val; IF no_more_rows THEN CLOSE latlongGrabber_cur; LEAVE the_loop; END IF; SELECT latitude_val, longitude_val; END LOOP the_loop; END $$ DELIMITER ; This function checks whether a point is inside a polygon. I'd like the function to test the points produced by the procedure. I can hard-code the polygon for now. (Once, I know how to combine these two functions, I'll use the same pattern to pull the polygons from the database). DROP FUNCTION IF EXISTS myWithin; DELIMITER $$ CREATE FUNCTION myWithin(p POINT, poly POLYGON) RETURNS INT(1) DETERMINISTIC BEGIN DECLARE n INT DEFAULT 0; DECLARE pX DECIMAL(9,6); DECLARE pY DECIMAL(9,6); DECLARE ls LINESTRING; DECLARE poly1 POINT; DECLARE poly1X DECIMAL(9,6); DECLARE poly1Y DECIMAL(9,6); DECLARE poly2 POINT; DECLARE poly2X DECIMAL(9,6); DECLARE poly2Y DECIMAL(9,6); DECLARE i INT DEFAULT 0; DECLARE result INT(1) DEFAULT 0; SET pX = X(p); SET pY = Y(p); SET ls = ExteriorRing(poly); SET poly2 = EndPoint(ls); SET poly2X = X(poly2); SET poly2Y = Y(poly2); SET n = NumPoints(ls); WHILE i<n DO SET poly1 = PointN(ls, (i+1)); SET poly1X = X(poly1); SET poly1Y = Y(poly1); IF ( ( ( ( poly1X <= pX ) && ( pX < poly2X ) ) || ( ( poly2X <= pX ) && ( pX < poly1X ) ) ) && ( pY > ( poly2Y - poly1Y ) * ( pX - poly1X ) / ( poly2X - poly1X ) + poly1Y ) ) THEN SET result = !result; END IF; SET poly2X = poly1X; SET poly2Y = poly1Y; SET i = i + 1; END WHILE; RETURN result; End $$ DELIMITER ; This function is called as follows: SET @point = PointFromText('POINT(5 5)') ; SET @polygon = PolyFromText('POLYGON((0 0, 0 10, 10 10, 10 0, 0 0))'); SELECT myWithin(@point, @polygon) AS result I've tested the stored procedure and the function and they work well. I just have to figure out how to combine them. I'd like to call the procedure with the offense parameter and have it test all of the latitudes and longitudes pulled from the database to see whether they are inside or outside of the polygon. Any advice or suggestions? Thank you. -Laxmidi

  Read the article

• Typesafe fire-and-forget asynchronous delegate invocation in C#

  - by LBushkin

  I recently found myself needing a typesafe "fire-and-forget" mechanism for running code asynchronously. Ideally, what I would want to do is something like: var myAction = (Action)(() => Console.WriteLine("yada yada")); myAction.FireAndForget(); // async invocation Unfortunately, the obvious choice of calling BeginInvoke() without a corresponding EndInvoke() does not work - it results in a slow resource leak (since the asyn state is held by the runtime and never released ... it's expecting an eventual call to EndInvoke(). I also can't run the code on the .NET thread pool because it may take a very long time to complete (it's advised to only run relatively short-lived code on the thread pool) - this makes it impossible to use the ThreadPool.QueueUserWorkItem(). Initially, I only needed this behavior for methods whose signature matches Action, Action<...>, or Func<...>. So I put together a set of extension methods (see listing below) that let me do this without running into the resource leak. There are overloads for each version of Action/Func. Unfortunately, I now want to port this code to .NET 4 where the number of generic parameters on Action and Func have been increased substantially. Before I write a T4 script to generate these, I was also hoping to find a simpler more elegant way to do this. Any ideas are welcome. public static class AsyncExt { public static void FireAndForget( this Action action ) { action.BeginInvoke(OnActionCompleted, action); } public static void FireAndForget<T1>( this Action<T1> action, T1 arg1 ) { action.BeginInvoke(arg1, OnActionCompleted<T1>, action); } public static void FireAndForget<T1,T2>( this Action<T1,T2> action, T1 arg1, T2 arg2 ) { action.BeginInvoke(arg1, arg2, OnActionCompleted<T1, T2>, action); } public static void FireAndForget<TResult>(this Func<TResult> func, TResult arg1) { func.BeginInvoke(OnFuncCompleted<TResult>, func); } public static void FireAndForget<T1,TResult>(this Func<T1, TResult> action, T1 arg1) { action.BeginInvoke(arg1, OnFuncCompleted<T1,TResult>, action); } // more overloads of FireAndForget<..>() for Action<..> and Func<..> private static void OnActionCompleted( IAsyncResult result ) { var action = (Action)result.AsyncState; action.EndInvoke(result); } private static void OnActionCompleted<T1>( IAsyncResult result ) { var action = (Action<T1>)result.AsyncState; action.EndInvoke( result ); } private static void OnActionCompleted<T1,T2>(IAsyncResult result) { var action = (Action<T1,T2>)result.AsyncState; action.EndInvoke(result); } private static void OnFuncCompleted<TResult>( IAsyncResult result ) { var func = (Func<TResult>)result.AsyncState; func.EndInvoke( result ); } private static void OnFuncCompleted<T1,TResult>(IAsyncResult result) { var func = (Func<T1, TResult>)result.AsyncState; func.EndInvoke(result); } // more overloads of OnActionCompleted<> and OnFuncCompleted<> }

  Read the article

• Nhibernate Migration from 1.0.2.0 to 2.1.2 and many-to-one save problems

  - by Meska

  Hi, we have an old, big asp.net application with nhibernate, which we are extending and upgrading some parts of it. NHibernate that was used was pretty old ( 1.0.2.0), so we decided to upgrade to ( 2.1.2) for the new features. HBM files are generated through custom template with MyGeneration. Everything went quite smoothly, except for one thing. Lets say we have to objects Blog and Post. Blog can have many posts, so Post will have many-to-one relationship. Due to the way that this application operates, relationship is done not through primary keys, but through Blog.Reference column. Sample mapings and .cs files: <?xml version="1.0" encoding="utf-8" ?> <id name="Id" column="Id" type="Guid"> <generator class="assigned"/> </id> <property column="Reference" type="Int32" name="Reference" not-null="true" /> <property column="Name" type="String" name="Name" length="250" /> </class> <?xml version="1.0" encoding="utf-8" ?> <id name="Id" column="Id" type="Guid"> <generator class="assigned"/> </id> <property column="Reference" type="Int32" name="Reference" not-null="true" /> <property column="Name" type="String" name="Name" length="250" /> <many-to-one name="Blog" column="BlogId" class="SampleNamespace.BlogEntity,SampleNamespace" property-ref="Reference" /> </class> And class files class BlogEntity { public Guid Id { get; set; } public int Reference { get; set; } public string Name { get; set; } } class PostEntity { public Guid Id { get; set; } public int Reference { get; set; } public string Name { get; set; } public BlogEntity Blog { get; set; } } Now lets say that i have a Blog with Id 1D270C7B-090D-47E2-8CC5-A3D145838D9C and with Reference 1 In old nhibernate such thing was possible: //this Blog already exists in database BlogEntity blog = new BlogEntity(); blog.Id = Guid.Empty; blog.Reference = 1; //Reference is unique, so we can distinguish Blog by this field blog.Name = "My blog"; //this is new Post, that we are trying to insert PostEntity post = new PostEntity(); post.Id = Guid.NewGuid(); post.Name = "New post"; post.Reference = 1234; post.Blog = blog; session.Save(post); However, in new version, i get an exception that cannot insert NULL into Post.BlogId. As i understand, in old version, for nhibernate it was enough to have Blog.Reference field, and it could retrieve entity by that field, and attach it to PostEntity, and when saving PostEntity, everything would work correctly. And as i understand, new NHibernate tries only to retrieve by Blog.Id. How to solve this? I cannot change DB design, nor can i assign an Id to BlogEntity, as objects are out of my control (they come prefilled as generic "ojbects" like this from external source)

  Read the article

• Converting OCaml to F#: F# equivelent of Pervasives at_exit

  - by Guy Coder

  I am converting the OCaml Format module to F# and tracked a problem back to a use of the OCaml Pervasives at_exit. val at_exit : (unit -> unit) -> unit Register the given function to be called at program termination time. The functions registered with at_exit will be called when the program executes exit, or terminates, either normally or because of an uncaught exception. The functions are called in "last in, first out" order: the function most recently added with at_exit is called first. In the process of conversion I commented out the line as the compiler did not flag it as being needed and I was not expecting an event in the code. I checked the FSharp.PowerPack.Compatibility.PervasivesModule for at_exit using VS Object Browser and found none. I did find how to run code "at_exit"? and How do I write an exit handler for an F# application? The OCaml line is at_exit print_flush with print_flush signature: val print_flush : (unit -> unit) Also in looking at the use of it during a debug session of the OCaml code, it looks like at_exit is called both at the end of initialization and at the end of each use of a call to the module. Any suggestions, hints on how to do this. This will be my first event in F#. EDIT Here is some of what I have learned about the Format module that should shed some light on the problem. The Format module is a library of functions for basic pretty printer commands of simple OCaml values such as int, bool, string. The format module has commands like print_string, but also some commands to say put the next line in a bounded box, think new set of left and right margins. So one could write: print_string "Hello" or open_box 0; print_string "<<"; open_box 0; print_string "p \/ q ==> r"; close_box(); print_string ">>"; close_box() The commands such as open_box and print_string are handled by a loop that interprets the commands and then decides wither to print on the current line or advance to the next line. The commands are held in a queue and there is a state record to hold mutable values such as left and right margin. The queue and state needs to be primed, which from debugging the test cases against working OCaml code appears to be done at the end of initialization of the module but before the first call is made to any function in the Format module. The queue and state is cleaned up and primed again for the next set of commands by the use of mechanisms for at_exit that recognize that the last matching frame for the initial call to the format modules has been removed thus triggering the call to at_exit which pushes out any remaining command in the queue and re-initializes the queue and state. So the sequencing of the calls to print_flush is critical and appears to be at more than what the OCaml documentation states.

  Read the article

• Suggestions on how to map from Domain (ORM) objects to Data Transfer Objects (DTO)

  - by FryHard

  The current system that I am working on makes use of Castle Activerecord to provide ORM (Object Relational Mapping) between the Domain objects and the database. This is all well and good and at most times actually works well! The problem comes about with Castle Activerecords support for asynchronous execution, well, more specifically the SessionScope that manages the session that objects belong to. Long story short, bad stuff happens! We are therefore looking for a way to easily convert (think automagically) from the Domain objects (who know that a DB exists and care) to the DTO object (who know nothing about the DB and care not for sessions, mapping attributes or all thing ORM). Does anyone have suggestions on doing this. For the start I am looking for a basic One to One mapping of object. Domain object Person will be mapped to say PersonDTO. I do not want to do this manually since it is a waste. Obviously reflection comes to mind, but I am hoping with some of the better IT knowledge floating around this site that "cooler" will be suggested. Oh, I am working in C#, the ORM objects as said before a mapped with Castle ActiveRecord. Example code: By @ajmastrean's request I have linked to an example that I have (badly) mocked together. The example has a capture form, capture form controller, domain objects, activerecord repository and an async helper. It is slightly big (3MB) because I included the ActiveRecored dll's needed to get it running. You will need to create a database called ActiveRecordAsync on your local machine or just change the .config file. Basic details of example: The Capture Form The capture form has a reference to the contoller private CompanyCaptureController MyController { get; set; } On initialise of the form it calls MyController.Load() private void InitForm () { MyController = new CompanyCaptureController(this); MyController.Load(); } This will return back to a method called LoadComplete() public void LoadCompleted (Company loadCompany) { _context.Post(delegate { CurrentItem = loadCompany; bindingSource.DataSource = CurrentItem; bindingSource.ResetCurrentItem(); //TOTO: This line will thow the exception since the session scope used to fetch loadCompany is now gone. grdEmployees.DataSource = loadCompany.Employees; }, null); } } this is where the "bad stuff" occurs, since we are using the child list of Company that is set as Lazy load. The Controller The controller has a Load method that was called from the form, it then calls the Asyc helper to asynchronously call the LoadCompany method and then return to the Capture form's LoadComplete method. public void Load () { new AsyncListLoad<Company>().BeginLoad(LoadCompany, Form.LoadCompleted); } The LoadCompany() method simply makes use of the Repository to find a know company. public Company LoadCompany() { return ActiveRecordRepository<Company>.Find(Setup.company.Identifier); } The rest of the example is rather generic, it has two domain classes which inherit from a base class, a setup file to instert some data and the repository to provide the ActiveRecordMediator abilities.

  Read the article

• System.Threading.Timer Doesn't Trigger my TimerCallBack Delegate

  - by Tom Kong

  Hi, I am writing my first Windows Service using C# and I am having some trouble with my Timer class. When the service is started, it runs as expected but the code will not execute again (I want it to run every minute) Please take a quick look at the attached source and let me know if you see any obvious mistakes! TIA using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Diagnostics; using System.Linq; using System.ServiceProcess; using System.Text; using System.Threading; using System.IO; namespace CXO001 { public partial class Service1 : ServiceBase { public Service1() { InitializeComponent(); } /* * Aim: To calculate and update the Occupancy values for the different Sites * * Method: Retrieve data every minute, updating a public value which can be polled */ protected override void OnStart(string[] args) { Daemon(); } public void Daemon() { TimerCallback tcb = new TimerCallback(On_Tick); TimeSpan duetime = new TimeSpan(0, 0, 1); TimeSpan interval = new TimeSpan(0, 1, 0); Timer querytimer = new Timer(tcb, null, duetime, interval); } protected override void OnStop() { } static int[] floorplanids = new int[] { 115, 114, 107, 108 }; public static List<Record> Records = new List<Record>(); static bool firstrun = true; public static void On_Tick(object timercallback) { //Update occupancy data for the last minute //Save a copy of the public values to HDD with a timestamp string starttime; if (Records.Count > 0) { starttime = Records.Last().TS; firstrun = false; } else { starttime = DateTime.Today.AddHours(7).ToString(); firstrun = true; } DateTime endtime = DateTime.Now; GetData(starttime, endtime); } public static void GetData(string starttime, DateTime endtime) { string connstr = "Data Source = 192.168.1.123; Initial Catalog = Brickstream_OPS; User Id = Brickstream; Password = bstas;"; DataSet resultds = new DataSet(); //Get the occupancy for each Zone foreach (int zone in floorplanids) { SQL s = new SQL(); string querystr = "SELECT SUM(DIRECTIONAL_METRIC.NUM_TO_ENTER - DIRECTIONAL_METRIC.NUM_TO_EXIT) AS 'Occupancy' FROM REPORT_OBJECT INNER JOIN REPORT_OBJ_METRIC ON REPORT_OBJECT.REPORT_OBJ_ID = REPORT_OBJ_METRIC.REPORT_OBJECT_ID INNER JOIN DIRECTIONAL_METRIC ON REPORT_OBJ_METRIC.REP_OBJ_METRIC_ID = DIRECTIONAL_METRIC.REP_OBJ_METRIC_ID WHERE (REPORT_OBJ_METRIC.M_START_TIME BETWEEN '" + starttime + "' AND '" + endtime.ToString() + "') AND (REPORT_OBJECT.FLOORPLAN_ID = '" + zone + "');"; resultds = s.Go(querystr, connstr, zone.ToString(), resultds); } List<Record> result = new List<Record>(); int c = 0; foreach (DataTable dt in resultds.Tables) { Record r = new Record(); r.TS = DateTime.Now.ToString(); r.Zone = dt.TableName; if (!firstrun) { r.Occupancy = (dt.Rows[0].Field<int>("Occupancy")) + (Records[c].Occupancy); } else { r.Occupancy = dt.Rows[0].Field<int>("Occupancy"); } result.Add(r); c++; } Records = result; MrWriter(); } public static void MrWriter() { StringBuilder output = new StringBuilder("Time,Zone,Occupancy\n"); foreach (Record r in Records) { output.Append(r.TS); output.Append(","); output.Append(r.Zone); output.Append(","); output.Append(r.Occupancy.ToString()); output.Append("\n"); } output.Append(firstrun.ToString()); output.Append(DateTime.Now.ToFileTime()); string filePath = @"C:\temp\CXO.csv"; File.WriteAllText(filePath, output.ToString()); } } }

  Read the article

• MVC design in Cocoa - are all 3 always necessary? Also: naming conventions, where to put Controller

  - by Nektarios

  I'm new to MVC although I've read a lot of papers and information on the web. I know it's somewhat ambiguous and there are many different interpretations of MVC patterns.. but the differences seem somewhat minimal My main question is - are M, V, and C always going to be necessary to be doing this right? I haven't seen anyone address this in anything I've read. Examples (I'm working in Cocoa/Obj-c although that shouldn't much matter).. 1) If I have a simple image on my GUI, or a text entry field that is just for a user's convenience and isn't saved or modified, these both would be V (view) but there's no M (no data and no domain processing going on), and no C to bridge them. So I just have some aspects that are "V" - seems fine 2) I have 2 different and visible windows that each have a button on them labeled as "ACTIVATE FOO" - when a user clicks the button on either, both buttons press in and change to say "DEACTIVATE FOO" and a third window appears with label "FOO". Clicking the button again will change the button on both windows to "ACTIVATE FOO" and will remove the third "FOO" window. In this case, my V consists of the buttons on both windows, and I guess also the third window (maybe all 3 windows). I definitely have a C, my Controller object will know about these buttons and windows and will get their clicks and hold generic states regarding windows and buttons. However, whether I have 1 button or 10 button, my window is called "FOO" or my window is called "BAR", this doesn't matter. There's no domain knowledge or data here - just control of views. So in this example, I really have "V" and "C" but no "M" - is that ok? 3) Final example, which I am running in to the most. I have a text entry field as my View. When I enter text in this, say a number representing gravity, I keep it in a Model that may do things like compute physics of a ball while taking in to account my gravity parameter. Here I have a V and an M, but I don't understand why I would need to add a C - a controller would just accept the signals from the View and pass it along to the Model, and vice versa. Being as the C is just a pure passthrough, it's really "junk" code and isn't making things any more reusable in my opinion. In most situations, when something changes I will need to change the C and M both in nearly identical ways. I realize it's probably an MVC beginner's mistake to think most situations call for only V and M.. leads me in to next subject 4) In Cocoa / Xcode / IB, I guess my Controllers should always be an instantiated object in IB? That is, I lay all of my "V" components in IB, and for each collection of View objects (things that are related) I should have an instantiated Controller? And then perhaps my Models should NOT be found in IB, and instead only found as classes in Xcode that tie in with Controller code found there. Is this accurate? This could explain why you'd have a Controller that is not really adding value - because you are keeping consistent.. 5) What about naming these things - for my above example about FOO / BAR maybe something that ends in Controller would be the C, like FancyWindowOpeningController, etc? And for models - should I suffix them with like GravityBallPhysicsModel etc, or should I just name those whatever I like? I haven't seen enough code to know what's out there in the wild and I want to get on the right track early on Thank you in advance for setting me straight or letting me know I'm on the right track. I feel like I'm starting to get it and most of what I say here makes sense, but validation of my guessing would help me feel confident..

  Read the article

• Lockless queue implementation ends up having a loop under stress

  - by Fozi

  I have lockless queues written in C in form of a linked list that contains requests from several threads posted to and handled in a single thread. After a few hours of stress I end up having the last request's next pointer pointing to itself, which creates an endless loop and locks up the handling thread. The application runs (and fails) on both Linux and Windows. I'm debugging on Windows, where my COMPARE_EXCHANGE_PTR maps to InterlockedCompareExchangePointer. This is the code that pushes a request to the head of the list, and is called from several threads: void push_request(struct request * volatile * root, struct request * request) { assert(request); do { request->next = *root; } while(COMPARE_EXCHANGE_PTR(root, request, request->next) != request->next); } This is the code that gets a request from the end of the list, and is only called by a single thread that is handling them: struct request * pop_request(struct request * volatile * root) { struct request * volatile * p; struct request * request; do { p = root; while(*p && (*p)->next) p = &(*p)->next; // <- loops here request = *p; } while(COMPARE_EXCHANGE_PTR(p, NULL, request) != request); assert(request->next == NULL); return request; } Note that I'm not using a tail pointer because I wanted to avoid the complication of having to deal with the tail pointer in push_request. However I suspect that the problem might be in the way I find the end of the list. There are several places that push a request into the queue, but they all look generaly like this: // device->requests is defined as struct request * volatile requests; struct request * request = malloc(sizeof(struct request)); if(request) { // fill out request fields push_request(&device->requests, request); sem_post(device->request_sem); } The code that handles the request is doing more than that, but in essence does this in a loop: if(sem_wait_timeout(device->request_sem, timeout) == sem_success) { struct request * request = pop_request(&device->requests); // handle request free(request); } I also just added a function that is checking the list for duplicates before and after each operation, but I'm afraid that this check will change the timing so that I will never encounter the point where it fails. (I'm waiting for it to break as I'm writing this.) When I break the hanging program the handler thread loops in pop_request at the marked position. I have a valid list of one or more requests and the last one's next pointer points to itself. The request queues are usually short, I've never seen more then 10, and only 1 and 3 the two times I could take a look at this failure in the debugger. I thought this through as much as I could and I came to the conclusion that I should never be able to end up with a loop in my list unless I push the same request twice. I'm quite sure that this never happens. I'm also fairly sure (although not completely) that it's not the ABA problem. I know that I might pop more than one request at the same time, but I believe this is irrelevant here, and I've never seen it happening. (I'll fix this as well) I thought long and hard about how I can break my function, but I don't see a way to end up with a loop. So the question is: Can someone see a way how this can break? Can someone prove that this can not? Eventually I will solve this (maybe by using a tail pointer or some other solution - locking would be a problem because the threads that post should not be locked, I do have a RW lock at hand though) but I would like to make sure that changing the list actually solves my problem (as opposed to makes it just less likely because of different timing).

  Read the article

• Reconciling a new BindingList into a master BindingList using LINQ

  - by Neo

  I have a seemingly simple problem whereby I wish to reconcile two lists so that an 'old' master list is updated by a 'new' list containing updated elements. Elements are denoted by a key property. These are my requirements: All elements in either list that have the same key results in an assignment of that element from the 'new' list over the original element in the 'old' list only if any properties have changed. Any elements in the 'new' list that have keys not in the 'old' list will be added to the 'old' list. Any elements in the 'old' list that have keys not in the 'new' list will be removed from the 'old' list. I found an equivalent problem here - http://stackoverflow.com/questions/161432/ - but it hasn't really been answered properly. So, I came up with an algorithm to iterate through the old and new lists and perform the reconciliation as per the above. Before anyone asks why I'm not just replacing the old list object with the new list object in its entirety, it's for presentation purposes - this is a BindingList bound to a grid on a GUI and I need to prevent refresh artifacts such as blinking, scrollbars moving, etc. So the list object must remain the same, only its updated elements changed. Another thing to note is that the objects in the 'new' list, even if the key is the same and all the properties are the same, are completely different instances to the equivalent objects in the 'old' list, so copying references is not an option. Below is what I've come up with so far - it's a generic extension method for a BindingList. I've put comments in to demonstrate what I'm trying to do. public static class BindingListExtension { public static void Reconcile<T>(this BindingList<T> left, BindingList<T> right, string key) { PropertyInfo piKey = typeof(T).GetProperty(key); // Go through each item in the new list in order to find all updated and new elements foreach (T newObj in right) { // First, find an object in the new list that shares its key with an object in the old list T oldObj = left.First(call => piKey.GetValue(call, null).Equals(piKey.GetValue(newObj, null))); if (oldObj != null) { // An object in each list was found with the same key, so now check to see if any properties have changed and // if any have, then assign the object from the new list over the top of the equivalent element in the old list foreach (PropertyInfo pi in typeof(T).GetProperties()) { if (!pi.GetValue(oldObj, null).Equals(pi.GetValue(newObj, null))) { left[left.IndexOf(oldObj)] = newObj; break; } } } else { // The object in the new list is brand new (has a new key), so add it to the old list left.Add(newObj); } } // Now, go through each item in the old list to find all elements with keys no longer in the new list foreach (T oldObj in left) { // Look for an element in the new list with a key matching an element in the old list if (right.First(call => piKey.GetValue(call, null).Equals(piKey.GetValue(oldObj, null))) == null) { // A matching element cannot be found in the new list, so remove the item from the old list left.Remove(oldObj); } } } } It can be called like this: _oldBindingList.Reconcile(newBindingList, "MyKey") However, I'm looking for perhaps a method of doing the same using LINQ type methods such as GroupJoin<, Join<, Select<, SelectMany<, Intersect<, etc. So far, the problem I've had is that each of these LINQ type methods result in brand new intermediary lists (as a return value) and really, I only want to modify the existing list for all the above reasons. If anyone can help with this, would be most appreciated. If not, no worries, the above method (as it were) will suffice for now. Thanks, Jason

  Read the article

• how use graphvis in C# application?

  - by ghasedak -

  i have a dot format file and i download graphvis for windows now how can i use graphvis to show a graph in my c# application? using System; using System.Collections.Generic; using System.ComponentModel; using System.Data; using System.Drawing; using System.Linq; using System.Text; using System.Windows.Forms; using VDS.RDF; using VDS.RDF.Parsing; using VDS.RDF.Query; using System.IO; using System.Windows; using System.Runtime.InteropServices; using VDS.RDF.Writing; using System.Diagnostics; namespace WindowsFormsApplication2 { public partial class first : Form { Graph g = new Graph(); string s1 = null; /**************************************DATA********************************************/ public first() { InitializeComponent(); } private void button1_Click(object sender, EventArgs e) { Stream myStream = null; var parser = new Notation3Parser(); var graph = new Graph(); OpenFileDialog openFileDialog1 = new OpenFileDialog(); openFileDialog1.Filter = "RDF files (*.n3)|*.n3"; openFileDialog1.FilterIndex = 1; openFileDialog1.RestoreDirectory = true; openFileDialog1.Multiselect = false; if (openFileDialog1.ShowDialog() == DialogResult.OK) { try { if ((myStream = openFileDialog1.OpenFile()) != null) { using (myStream) { string s = openFileDialog1.FileName.ToString(); string w= Directory.GetCurrentDirectory().ToString(); string Fname = openFileDialog1.SafeFileName.ToString(); File.Copy(s,Path.Combine(w,Fname),true); // Insert code to read the stream here. Win32.AllocConsole(); s1 = Path.Combine(w, Fname); insertNodeButton.Visible = true; delBut.Visible = true; simi.Visible = true; showNodes showNodes1 = new showNodes(s1); g = showNodes1.returngraph(); Console.Read(); Win32.FreeConsole(); // g.SaveToFile("firstfile.n3"); this.Show(); } } } catch (Exception ex) { MessageBox.Show("Error: Could not read file from disk. Original error: " + ex.Message); } } GraphVizWriter hi = new GraphVizWriter(); hi.Save(g, "c:\\ahmad.dot"); } private void button2_Click(object sender, EventArgs e) { string strCmdLine = Application.StartupPath + "\\Tools\\rdfEditor.exe"; //string strCmdLine = "DIR"; MessageBox.Show(strCmdLine); System.Diagnostics.Process process1; process1 = new System.Diagnostics.Process(); //Do not receive an event when the process exits. process1.EnableRaisingEvents = false; //The "/C" Tells Windows to Run The Command then Terminate System.Diagnostics.Process.Start(strCmdLine); process1.Close(); } private void Form1_Load(object sender, EventArgs e) { } private void insertNodeButton_Click(object sender, EventArgs e) { //Graph parentvalue = this.g; //String parentvalueadress = this.s1; addTriple a1 = new addTriple(); a1.G = g; a1.BringToFront(); a1.ShowDialog(); g = a1.G; g.SaveToFile("c:\\Hi.n3"); } this is my code i want to visul saly dot file format to show a graph with graphvis

  Read the article

• How to best propagate changes upwards a hierarchical structure for binding?

  - by H.B.

  If i have a folder-like structure that uses the composite design pattern and i bind the root folder to a TreeView. It would be quite useful if i can display certain properties that are being accumulated from the folder's contents. The question is, how do i best inform the folder that changes occurred in a child-element so that the accumulative properties get updated? The context in which i need this is a small RSS-FeedReader i am trying to make. This are the most important objects and aspects of my model: Composite interface: public interface IFeedComposite : INotifyPropertyChanged { string Title { get; set; } int UnreadFeedItemsCount { get; } ObservableCollection<FeedItem> FeedItems { get; } } FeedComposite (aka Folder) public class FeedComposite : BindableObject, IFeedComposite { private string title = ""; public string Title { get { return title; } set { title = value; NotifyPropertyChanged("Title"); } } private ObservableCollection<IFeedComposite> children = new ObservableCollection<IFeedComposite>(); public ObservableCollection<IFeedComposite> Children { get { return children; } set { children.Clear(); foreach (IFeedComposite item in value) { children.Add(item); } NotifyPropertyChanged("Children"); } } public FeedComposite() { } public FeedComposite(string title) { Title = title; } public ObservableCollection<FeedItem> FeedItems { get { ObservableCollection<FeedItem> feedItems = new ObservableCollection<FeedItem>(); foreach (IFeedComposite child in Children) { foreach (FeedItem item in child.FeedItems) { feedItems.Add(item); } } return feedItems; } } public int UnreadFeedItemsCount { get { return (from i in FeedItems where i.IsUnread select i).Count(); } } Feed: public class Feed : BindableObject, IFeedComposite { private string url = ""; public string Url { get { return url; } set { url = value; NotifyPropertyChanged("Url"); } } ... private ObservableCollection<FeedItem> feedItems = new ObservableCollection<FeedItem>(); public ObservableCollection<FeedItem> FeedItems { get { return feedItems; } set { feedItems.Clear(); foreach (FeedItem item in value) { AddFeedItem(item); } NotifyPropertyChanged("Items"); } } public int UnreadFeedItemsCount { get { return (from i in FeedItems where i.IsUnread select i).Count(); } } public Feed() { } public Feed(string url) { Url = url; } Ok, so here's the thing, if i bind a TextBlock.Text to the UnreadFeedItemsCount there won't be simple notifications when an item is marked unread, so one of my approaches has been to handle the PropertyChanged event of every FeedItem and if the IsUnread-Property is changed i have my Feed make a notification that the property UnreadFeedItemsCount has been changed. With this approach i also need to handle all PropertyChanged events of all Feeds and FeedComposites in Children of FeedComposite, from the sound of it, it should be obvious that this is not such a very good idea, you need to be very careful that items never get added or removed to any collection without having attached the PropertyChanged event handler first and things like that. Also: What do i do with the CollectionChanged-Events which necessarily also cause a change in the sum of the unread items count? Sounds like more event handling fun. It is such a mess, it would be great if anyone has an elegant solution to this since i don't want the feed-reader to end up as awful as my first attempt years ago when i didn't even know about DataBinding...

  Read the article

• How to make Net::Msmnr run?

  - by codeholic

  There's Net::Msmgr module on CPAN. It's written clean and the code looks trustworthy at the first glance. However this module seems to be beta and there is little documentation and no tests :-/ Has anyone used this module in production? I haven't managed to make it run by now, because it requires all event loop processing to be done in the application and as I've already said there is little documentation and no working examples to study. That's where I've gone so far: #!/usr/bin/perl use strict; use warnings; use Event; use Net::Msmgr::Object; use Net::Msmgr::Session; use Net::Msmgr::User; use constant DEBUG => 511; use constant EVENT_TIMEOUT => 5; # seconds my ($username, $password) = qw/[email protected] my.password/; my $buddy = '[email protected]'; my $user = Net::Msmgr::User->new(user => $username, password => $password); my $session = Net::Msmgr::Session->new; $session->debug(DEBUG); $session->login_handler(\&login_handler); $session->user($user); my $conv; sub login_handler { my $self = shift; print "LOGIN\n"; $self->ui_state_nln; $conv = $session->ui_new_conversation; $conv->invite($buddy); } our %watcher; sub ConnectHandler { my ($connection) = @_; warn "CONNECT\n"; my $socket = $connection->socket; $watcher{$connection} = Event->io(fd => $socket, cb => [ $connection, '_recv_message' ], poll => 're', desc => 'recv_watcher', repeat => 1); } sub DisconnectHandler { my $connection = shift; print "DISCONNECT\n"; $watcher{$connection}->cancel; } $session->connect_handler(\&ConnectHandler); $session->disconnect_handler(\&DisconnectHandler); $session->Login; Event::loop(); That's what it outputs: Dispatch Server connecting to: messenger.hotmail.com:1863 Dispatch Server connected CONNECT Dispatch Server >>>VER 1 MSNP2 CVR0 --> VER 1 MSNP2 CVR0 Dispatch Server >>>USR 2 MD5 I [email protected] --> USR 2 MD5 I [email protected] Dispatch Server <<<VER 1 CVR0 <-- VER 1 CVR0 And that's all, here it hangs. The handler on login is not being triggered. What am I doing wrong?

  Read the article

• WPF: Binding to ListBoxItem.IsSelected doesn't work for off-screen items

  - by Qwertie

  In my program I have a set of view-model objects to represent items in a ListBox (multi-select is allowed). The viewmodel has an IsSelected property that I would like to bind to the ListBox so that selection state is managed in the viewmodel rather than in the listbox itself. However, apparently the ListBox doesn't maintain bindings for most of the off-screen items, so in general the IsSelected property is not synchronized correctly. Here is some code that demonstrates the problem. First XAML: <StackPanel> <StackPanel Orientation="Horizontal"> <TextBlock>Number of selected items: </TextBlock> <TextBlock Text="{Binding NumItemsSelected}"/> </StackPanel> <ListBox ItemsSource="{Binding Items}" Height="200" SelectionMode="Extended"> <ListBox.ItemContainerStyle> <Style TargetType="{x:Type ListBoxItem}"> <Setter Property="IsSelected" Value="{Binding IsSelected}"/> </Style> </ListBox.ItemContainerStyle> </ListBox> <Button Name="TestSelectAll" Click="TestSelectAll_Click">Select all</Button> </StackPanel> C# Select All handler: private void TestSelectAll_Click(object sender, RoutedEventArgs e) { foreach (var item in _dataContext.Items) item.IsSelected = true; } C# viewmodel: public class TestItem : NPCHelper { TestDataContext _c; string _text; public TestItem(TestDataContext c, string text) { _c = c; _text = text; } public override string ToString() { return _text; } bool _isSelected; public bool IsSelected { get { return _isSelected; } set { _isSelected = value; FirePropertyChanged("IsSelected"); _c.FirePropertyChanged("NumItemsSelected"); } } } public class TestDataContext : NPCHelper { public TestDataContext() { for (int i = 0; i < 200; i++) _items.Add(new TestItem(this, i.ToString())); } ObservableCollection<TestItem> _items = new ObservableCollection<TestItem>(); public ObservableCollection<TestItem> Items { get { return _items; } } public int NumItemsSelected { get { return _items.Where(it => it.IsSelected).Count(); } } } public class NPCHelper : INotifyPropertyChanged { public event PropertyChangedEventHandler PropertyChanged; public void FirePropertyChanged(string prop) { if (PropertyChanged != null) PropertyChanged(this, new PropertyChangedEventArgs(prop)); } } Two separate problems can be observed. If you click the first item and then press Shift+End, all 200 items should be selected; however, the heading reports that only 21 items are selected. If you click "Select all" then all items are indeed selected. If you then click an item in the ListBox you would expect the other 199 items to be deselected, but this does not happen. Instead, only the items that are on the screen (and a few others) are deselected. All 199 items will not be deselected unless you first scroll through the list from beginning to end (and even then, oddly enough, it doesn't work if you perform scrolling with the little scroll box). My questions are: Can someone explain precisely why this occurs? Can I avoid or work around the problem?

  Read the article

• Why does Perl's Net::Msmgr hang when I try to authenticate?

  - by codeholic

  There's Net::Msmgr module on CPAN. It's written clean and the code looks trustworthy at the first glance. However this module seems to be beta and there is little documentation and no tests :-/ Has anyone used this module in production? I haven't managed to make it run by now, because it requires all event loop processing to be done in the application and as I've already said there is little documentation and no working examples to study. That's where I've gone so far: #!/usr/bin/perl use strict; use warnings; use Event; use Net::Msmgr::Object; use Net::Msmgr::Session; use Net::Msmgr::User; use constant DEBUG => 511; use constant EVENT_TIMEOUT => 5; # seconds my ($username, $password) = qw/[email protected] my.password/; my $buddy = '[email protected]'; my $user = Net::Msmgr::User->new(user => $username, password => $password); my $session = Net::Msmgr::Session->new; $session->debug(DEBUG); $session->login_handler(\&login_handler); $session->user($user); my $conv; sub login_handler { my $self = shift; print "LOGIN\n"; $self->ui_state_nln; $conv = $session->ui_new_conversation; $conv->invite($buddy); } our %watcher; sub ConnectHandler { my ($connection) = @_; warn "CONNECT\n"; my $socket = $connection->socket; $watcher{$connection} = Event->io(fd => $socket, cb => [ $connection, '_recv_message' ], poll => 're', desc => 'recv_watcher', repeat => 1); } sub DisconnectHandler { my $connection = shift; print "DISCONNECT\n"; $watcher{$connection}->cancel; } $session->connect_handler(\&ConnectHandler); $session->disconnect_handler(\&DisconnectHandler); $session->Login; Event::loop(); That's what it outputs: Dispatch Server connecting to: messenger.hotmail.com:1863 Dispatch Server connected CONNECT Dispatch Server >>>VER 1 MSNP2 CVR0 --> VER 1 MSNP2 CVR0 Dispatch Server >>>USR 2 MD5 I [email protected] --> USR 2 MD5 I [email protected] Dispatch Server <<<VER 1 CVR0 <-- VER 1 CVR0 And that's all, here it hangs. The handler on login is not being triggered. What am I doing wrong?

  Read the article

• New cast exception with VS2010/.Net 4

  - by Trevor

  [ Updated 25 May 2010 ] I've recently upgraded from VS2008 to VS2010, and at the same time upgraded to .Net 4. I've recompiled an existing solution of mine and I'm encountering a Cast exception I did not have before. The structure of the code is simple (although the actual implementation somewhat more complicated). Basically I have: public class SomeClass : ISomeClass { // Stuff } public static class ClassFactory { public static IInterface GetClassInstance<IInterface>(Type classType) { return (IInterface)Activator.CreateInstance(classType); // This throws a cast exception } } // Call the factory with: ISomeClass anInstance = ClassFactory.GetClassInstance<ISomeClass>(typeof(SomeClass)); Ignore the 'sensibleness' of the above - its provides just a representation of the issue rather than the specifics of what I'm doing (e.g. constructor parameters have been removed). The marked line throws the exception: Unable to cast object of type 'Namespace.SomeClass' to type 'Namespace.ISomeClass'. I suspect it may have something to do with the additional DotNet security (and in particular, explicit loading of assemblies, as this is something my app does). The reason I suspect this is that I have had to add to the config file the setting: <runtime> <loadFromRemoteSources enabled="true" /> </runtime> .. but I'm unsure if this is related. Update I see (from comments) that my basic code does not reproduce the issue by itself. Not surprising I suppose. It's going to be tricky to identify which part of a largish 3-tier CQS system is relevant to this problem. One issue might be that there are multiple assemblies involved. My static class is actually a factory provider, and the 'SomeClass' is a class factory (relevant in that the factories are 'registered' within the app via explicit assembly/type loading - see below) . Upfront I use reflection to 'register' all factories (i.e. classes that implement a particular interface) and that I do this when the app starts by identifying the relevant assemblies, loading them and adding them to a cache using (in essence): Loop over (file in files) { Assembly assembly = Assembly.LoadFile(file); baseAssemblyList.Add(assembly); } Then I cache the available types in these assemblies with: foreach (Assembly assembly in _loadedAssemblyList) { Type[] assemblyTypes = assembly.GetTypes(); _loadedTypesCache.AddRange(assemblyTypes); } And then I use this cache to do a variety of reflection operations, including 'registering' of factories, which involves looping through all loaded (cached) types and finding those that implement the (base) Factory interface. I've experienced what may be a similar problem in the past (.Net 3.5, so not exactly the same) with an architecture that involved dynamically creating classes on the server and streaming the compiled binary of those classes to the client app. The problem came when trying to deserialize an instance of the dynamic class on the client from a remote call: the exception said the class type was not know, even though the source and destination types were exactly the same name (including namespace). Basically the cross boundry versions of the class were not recognised as being the same. I solved that by intercepting the deserialization process and explicitly defining the deseriazation class type in the context of the local assemblies. This experience is what makes me think the types are considered mismatched because (somehow) the interface of the actual SomeClass object, and the interface of passed into the Generic method are not considered the same type. So (possibly) my question for those more knowledgable about C#/DotNet is: How does the class loading work that somehow my app thinks there are two versions/types of the interface type and how can I fit that? [ whew ... anyone who got here is quite patient .. thanks ]

  Read the article

• Creating a custom module for Orchard

  - by Moran Monovich

  I created a custom module using this guide from Orchard documentation, but for some reason I can't see the fields in the content type when I want to create a new one. this is my model: public class CustomerPartRecord : ContentPartRecord { public virtual string FirstName { get; set; } public virtual string LastName { get; set; } public virtual int PhoneNumber { get; set; } public virtual string Address { get; set; } public virtual string Profession { get; set; } public virtual string ProDescription { get; set; } public virtual int Hours { get; set; } } public class CustomerPart : ContentPart<CustomerPartRecord> { [Required(ErrorMessage="you must enter your first name")] [StringLength(200)] public string FirstName { get { return Record.FirstName; } set { Record.FirstName = value; } } [Required(ErrorMessage = "you must enter your last name")] [StringLength(200)] public string LastName { get { return Record.LastName; } set { Record.LastName = value; } } [Required(ErrorMessage = "you must enter your phone number")] [DataType(DataType.PhoneNumber)] public int PhoneNumber { get { return Record.PhoneNumber; } set { Record.PhoneNumber = value; } } [StringLength(200)] public string Address { get { return Record.Address; } set { Record.Address = value; } } [Required(ErrorMessage = "you must enter your profession")] [StringLength(200)] public string Profession { get { return Record.Profession; } set { Record.Profession = value; } } [StringLength(500)] public string ProDescription { get { return Record.ProDescription; } set { Record.ProDescription = value; } } [Required(ErrorMessage = "you must enter your hours")] public int Hours { get { return Record.Hours; } set { Record.Hours = value; } } } this is the Handler: class CustomerHandler : ContentHandler { public CustomerHandler(IRepository<CustomerPartRecord> repository) { Filters.Add(StorageFilter.For(repository)); } } the Driver: class CustomerDriver : ContentPartDriver<CustomerPart> { protected override DriverResult Display(CustomerPart part, string displayType, dynamic shapeHelper) { return ContentShape("Parts_Customer", () => shapeHelper.Parts_BankCustomer( FirstName: part.FirstName, LastName: part.LastName, PhoneNumber: part.PhoneNumber, Address: part.Address, Profession: part.Profession, ProDescription: part.ProDescription, Hours: part.Hours)); } //GET protected override DriverResult Editor(CustomerPart part, dynamic shapeHelper) { return ContentShape("Parts_Customer", () => shapeHelper.EditorTemplate( TemplateName:"Parts/Customer", Model: part, Prefix: Prefix)); } //POST protected override DriverResult Editor(CustomerPart part, IUpdateModel updater, dynamic shapeHelper) { updater.TryUpdateModel(part, Prefix, null, null); return Editor(part, shapeHelper); } the migration: public class Migrations : DataMigrationImpl { public int Create() { // Creating table CustomerPartRecord SchemaBuilder.CreateTable("CustomerPartRecord", table => table .ContentPartRecord() .Column("FirstName", DbType.String) .Column("LastName", DbType.String) .Column("PhoneNumber", DbType.Int32) .Column("Address", DbType.String) .Column("Profession", DbType.String) .Column("ProDescription", DbType.String) .Column("Hours", DbType.Int32) ); return 1; } public int UpdateFrom1() { ContentDefinitionManager.AlterPartDefinition("CustomerPart", builder => builder.Attachable()); return 2; } public int UpdateFrom2() { ContentDefinitionManager.AlterTypeDefinition("Customer", cfg => cfg .WithPart("CommonPart") .WithPart("RoutePart") .WithPart("BodyPart") .WithPart("CustomerPart") .WithPart("CommentsPart") .WithPart("TagsPart") .WithPart("LocalizationPart") .Creatable() .Indexed()); return 3; } } Can someone please tell me if I am missing something?

  Read the article

< Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >