Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 352/1221 | < Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >

• Windows Server 2008 R2 loses ability to connect to network share

  - by JamesB

  I could sure use some help with this one: I've got two Windows Server 2008 R2 x64 Terminal Servers, as well as several 2003 servers (DNS / Wins / AD / DC). On the two 2008 boxes, every now and then they will get in this mode where you can't map a drive to a random server. I say random server because it's not always the same server that you can't map to. Here is a summary of what I can and can't do: net view \\servername Sometimes this works, sometimes it does not. net view \\FQDN This always works. net view \\IPAddress This always works. ping servername Sometimes this works, sometimes it does not. ping FQDN This always works. ping IPAddress This always works. I've been looking all over for a solution to this. It sure seems like Microsoft would have a hotfix by now. The kicker to this is that it sometimes works great, especially after a reboot. It may run for 2 weeks just fine, but all of a sudden it will fail to resolve the remote server name. It will then be this way for a few days, then it might start working again. Also, while it's in the mode of not working, the other servers have no problem getting there. It's just these 2008 R2 Terminal Servers. Setting a static entry in the Hosts file and LMHosts does not make it work. All servers have static IPs and they are registered in DNS and Wins just fine. Here is a long thread on MS Technet of the exact same problem, but they don't have a good solution. Here is their workaround (It was from June of 2010): Good news - a hotfix is in the works and a workaround has been identified: Root cause is that since this is SMB1 all user sessions are on a single TCP connection to the remote server. The first user to initiate a connection to the remote SMB server has their logon-ID added to the structure defining the connection. If that user logs off all subsequent uses of that TCP session fail as the logon-id is no longer valid. As a workaround for now to keep the issue from happening you will want to have the user not logoff the Terminal Server only disconnect their sessions. Any word from anyone out there about a solution? Any help would sure be appreciated. Thanks, James

  Read the article

• I don't get any Internet when I connect connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 [on hold]

  - by Asif Akhtar

  I am using Cisco DPC3825 DOCSIS 3.0 Gateway as my modem and router right now and it works fine on a computer directly connected to Cisco DPC3825 DOCSIS 3.0 Gateway with wire but I am getting very low/poor signal strength on my wireless computer due to which I am looking to install DLink DIR-625 as my router but because when I connect Cisco DPC3825 DOCSIS 3.0 Gateway with DLink DIR-625 and connect my computer with wire to DIR-625 then I don’t get any Internet.(I get Internet when I connect my computer with wire with Cisco DPC3825 DOCSIS 3.0 and I know there is nothing wrong with DLink DIR-625).

  Read the article

• Transferring NMap scans between machines

  - by Andrew Bolster

  Anyone know if its possible to halt a running nmap scan and for another scan on a different machine to 'pick up where it left off'?

  Read the article

• Why is my iPhone WIFI so slow at home?

  - by John Fouhy

  When my iPhone is connected to my home wireless network, the internet is unusably slow. I installed the speedtest.net application; here are some results from tonight: Down: 0.0kB/s, Up: 0.0kB/s, ping: 2230ms Down: 2.5kB/s, Up: 40.5kB/s, ping: 2182ms Down: 0.0kB/s, Up: 20.0kB/s, ping: 197ms For comparison, here is the result from my iMac to the same server, which is on the same wireless network (and has no wired connection): Down: 139kB/s, Up: 53.8kB/s, ping: 182ms Neither my iMac nor the Dell laptop also on the network have experienced the wifi problems I get with my iPhone. On the other hand, I tried browsing a website on the wireless network at work with no problems. EDIT: SpeedTest at work gives me 156kB/s down. EDIT2: Girlfriend (owner of the Dell) reports actually the internet is sometimes very slow. Perhaps there is more going on. No problems with my iMac. My router is a ASUS WL-500g Premium V2 running OpenWrt Kamikaze with X-Wrt Extensions 8.09.

  Read the article

• How to connect a wifi router to a cable modem router?

  - by DavidD

  Here's the thing: I have a cable modem router (Thomson TCW710) with wifi-g that I rent from my cable company. I would like to use a wireless-n router (D-Link DIR-655, that I received for free) with it in order to take advantage of the faster wifi. I basically need advice on how to architecture my home network with these two beasts. What configuration should I need to apply on my old and new router to make it all work? The two routers will of course be connected together with a RJ-45 cable.

  Read the article

• Host ::1 resolves to remote IP

  - by thebuckst0p

  /etc/hosts files usually have this line, ::1 localhost. I thought ::1 was the equivalent of 127.0.0.1/localhost, and from my reading it seems to be the IPv6 version. So I was using it in Apache for firewalling, "Allow from ::1" and it only allowed local. Then suddenly that stopped working, so I pinged ::1 and got a remote IP address. I tracerouted it and it went through my ISP, through some Microsoft server, then another half dozen steps of asterisks... I'm not sure why this would be (the remote IP), but it doesn't seem good. I grep'd my hard drive for the remote IP and it doesn't appear anywhere. Is this some indicator that I'm being hacked, or normal behavior? Maybe my IPv6 settings are wrong? (This is a brand new MacBookPro with Snow Leopard.) Any ideas about this would be great - what is ::1 supposed to be, why would it be remote, should I be worried, how do I get it back to localhost? Thank you!

  Read the article

• netkit: why cant my router 4 pc4 ping my router 1 pc1 - how can I solve this please?

  - by donok

  Below I have four routers connected but my pc1 on r1 cannot ping my pc4 on r4 and also my pc2 on r2 cant ping my pc4 on r4 and vice versa. Below is a network diagram: and the configurations are below that, could anyone help me please on making them accessible? ![connecting 4 routers][1] I cant post my diagram on serverfault(less than 10 rep) so I did on stackoverflow and asked the same question. pc1: ifconfig eth0 195.11.14.5 netmask 255.255.255.0 broadcast 195.11.14.255 up route add default gw 195.11.14.1 dev eth0 pc2.start: ifconfig eth0 200.1.1.7 netmask 255.255.255.0 broadcast 200.1.1.255 up route add default gw 200.1.1.1 dev eth0 pc3: ifconfig eth0 195.20.14.9 netmask 255.255.255.0 broadcast 195.20.1.255 up route add default gw 195.20.14.1 dev eth0 pc4: ifconfig eth0 200.2.1.11 netmask 255.255.255.0 broadcast 200.2.1.255 up route add default gw 200.2.1.1 dev eth0 r1: ifconfig eth0 195.11.14.1 netmask 255.255.255.0 broadcast 195.11.14.255 up ifconfig eth1 100.0.0.9 netmask 255.255.255.252 broadcast 100.0.0.11 up route add -net 200.1.1.0 netmask 255.255.255.0 gw 100.0.0.10 dev eth1 route add default gw 100.0.0.10 lab.conf: if you need more on that Ill post it up but I think most of the info is there. Any help would be greatly appreciated especially trying to make a connection between pc4 and pc1, even if you think it does not make sense please explain why. Thank you.

  Read the article

• How do I set or remove a Windows SMB password?

  - by David Is Not Here

  I recently purchased a computer with the intention of using it as network-attached storage. It presently has no Windows password and only one account. Can I create two different shares (share two different folders) in different ways -- make one publicly accessible, and make another only visible to people with a certain username/password combination? Creating multiple users isn't a problem, I just can't figure out where to start within Windows.

  Read the article

• very slow internet with Linksys WRT54GL only in wireless mode (wired is OK)

  - by gojira

  I bought a new Cisco Linksys WRT54GL router to connect my laptop (running Windows 7) to the internet. I installed Tomato 1.28 firmware on the router. When I connect the laptop to the router via ethernet cable, everything is fine and I get extremely fast up- and download speeds. When I connect wirelesssly however, websites load extremely slow - it takes dozens of seconds to load a website! <-- This is my question, how can I fix the wireless speed issue? Gmail for example is unusable this way. I tried speedtest.net, but this always fails in the upload part of the test so I can't even test the bandwidth (could the fact that it fails in the upload part, not the download part, be an indication what the problem is?!). I have isolated the problem a bit, I am convinced it has to do either with the router itself, the router settings, or the settings of the wireless connection in Win 7. Because previously, I was using another router by Buffalo and I had no problems whatsoever. I have tried to reproduce the settings from the Bufallo router as closely as possible on the Linksys router (same channel, same encryption etc). The download speed problem only occurs with the Linksys router, and only in wireless mode! When I exchange the Linksys router with the Buffalo router I have here for testing, the wireless speed is up to normal again. Also, before I had installed the Tomato firmware I had exactly the same problem, so it has nothing to do with the firmware itself. Notes & things I already tried: Changing the channel: does not seem to affect anything, I am also on the same channel (10) which I was previously on when I had a Buffalo router. QoS is off. Ping to the router itself is OK, ~ 1 ms. Some current settings of the linksys router: WAN / Internet Type: DHCP Wirelesss Mode: Access Point B/G Mode: Mixed Broadcast: check Channel: 10 - 2.457 GHz Security: WPA2 Personal Encryption: AES

  Read the article

• Ubuntu getting wrong hostname from DHCP

  - by sam

  When provisioning new Ubuntu Precise (12.04) servers, the hostname they're getting seems to be generated from the DNS search path, not a reverse lookup on the hostname. Take the following configuration BIND is configured with the hostname, and reverse name Normal zone $TTL 600 $ORIGIN srv.local.net. @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. @ IN MX 5 mail.local.net. my-new-server IN A 10.32.2.30 And reverse @ IN SOA ns0.local.net. hostmaster.local.net. ( 2014082101 10800 3600 604800 600 ) @ IN NS ns0.local.net. $ORIGIN 32.10.in-addr.arpa. 30.2 IN PTR my-new-server.srv.local.net. Then DHCPD is configured to hand out static leases based on mac addresses like so subnet 10.32.2.0 netmask 255.255.254.0 { option subnet-mask 255.255.254.0; option routers 10.32.2.1; option domain-name-servers 10.32.2.1; option domain-name "util.of1.local.net of1.local.net srv.local.net"; site-option-space "pxelinux"; option pxelinux.magic f1:00:74:7e; if exists dhcp-parameter-request-list { option dhcp-parameter-request-list = concat(option dhcp-parameter-request-list,d0,d1,d2,d3); } group { option pxelinux.configfile "pxelinux.cfg/pxeboot"; host my-new-server { fixed-address my-new-server.srv.local.net; hardware ethernet aa:aa:aa:bb:bb:bb; } } } So the hostname should be my-new-server.srv.local.net, however when building a Ubuntu 12.04 node, the hostname ends up as my-new-server.util.of1.local.net When building Lucid (10.04) hosts, the hostname will be correct, it's only on Precise/12.04 nodes we have the problem. Doing a normal and reverse lookup on the host and IP returns the correct result Sams-MacBook-Pro:~ sam$ host my-new-server my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host my-new-server.srv.local.net my-new-server.srv.local.net has address 10.32.2.30 Sams-MacBook-Pro:~ sam$ host 10.32.2.30 30.2.32.10.in-addr.arpa domain name pointer my-new-server.srv.local.net. The contents of the hosts file is incorrect too 127.0.0.1 localhost 127.0.1.1 my-new-server.util.of1.local.net of1.local.net srv.local.net my-new-server So it looks like when it creates the hosts file, it puts the entire contents of the DNS search path into the local address so the FQDN according to the server is the short hostname as defined, then the first domain in the search path. Is there a way to get around this behaviour, or fix this so it gets the hostname correctly? It's picking up the first part of the hostname, then the rest is wrong.

  Read the article

• How configure 2 Lan cards in Windows 7/8 pc one to connect to Internet and other to Local Network

  - by Maharshi Raval

      I am about to install a dedicated VOIP server in our office. It is a 3CX pbx system on Windows 7/8 machine. The environment currently is a Windows SBS 2011 with 8 client machines. I want to use a dedicated broadband connection for the PBX (3CX) box, but the box also needs to be accessible in the local network as we will be using IP Phones and software IP phones. How configure two network cards on PBX box, so that one will be always used to connect to our SIP host over the Internet and the other will be connected to local network accessible from other client pc to connect to the pbx system. It must be noted that currently the Windows SBS 2011 acts as the Primary Domain Controller and gateway for all the client machines.     I cannot use a load balancer as it will conflict and cause issues within the current setup of our SBS2011 as it is also our Exchange Server. Any input is much appreciated. thanks in advance

  Read the article

• Does VoIP packets travel through the internet link in LAN calls?

  - by Jader Dias

  If both parties in a call are in the same LAN, does the SIP/Skype call voice packets travel in and out through the internet? How to avoid it? I want to save bandwidth and improve call quality.

  Read the article

• Asus EEE PC 1005HA (XP Home) refuses to connect to Virgin Mobile MiFi

  - by Dennis Wurster

  My client has an Asus EEE PC model 1005HA, and we're attempting to connect it to the WiFi network created by a VirginMobile MiFi unit. They also have a MacBook Pro with Snow Leopard that has absolutely no issue connecting to the MiFi. The specific symptom is that the netbook fails to lease an IP address from the MiFi unit. I supply the 12-digit numerical password (WPA) to the netbook, it throws a 'waiting for network' dialog with an indeterminate progress indicator, and then times out. Update: We've determined that this behavior has stopped when the EEE PC and the MiFi unit were taken out of the client's home, and to a different home that didn't have an existing wifi network. Similarly, when taken to a third location that didn't have wifi, the EEE PC and MiFi got along swimmingly. My current theory is that the existing wifi networks and the wifi leg of the MiFi unit are on the same channel and competing with one another. Perhaps the MacBook Pro has the capability to overcome this interference, while the EEE PC doesn't.

  Read the article

• Setup windows 2012 AD in Hyper-V for a Test environment

  - by hub

  Im trying to setup a Windos 2012 R2 test environment on my work computer (a laptop). I have a AD, DHCP and DNS server on server A, and a client connecting to the doman and that works. The client can ping the AD server and gets a valid IP adress. If I ping google.com from the client I get the IP adress but I dont get any responses (request time out). If i ping google.com from server A it works as it should. Server A have a connection to the Internet through a "external network switch" in hyper-v, which gets its internet from a router and the client is connected to a "internal network switch". May the poblem be that server A is behind a router? Can I make this solution to work regadless the network my laptop is connected to? At home i have one IP adress, at work its a totally different range. What I would like is to use my laptops internet connection, regardless wifi or wired, to act as incomming internet, is this possible?

  Read the article

• Why can't my networks reach each other?

  - by HOLOGRAPHICpizza

  We have two Buffalo WZR-HP-G300NH2 routers, with the default firmware, DD-WRT v24SP2-MULTI (10/31/11) std - build 17798. Each has a separate cable internet connection with a public static IP address. They are both in the 24.123.68.0/24 space. Both of them can contact pretty much the whole internet, and they can both be accessed out on the internet with no problem, but for some reason they can't talk to each other! When I try to ping one from the other I always get "Destination Host Unreachable". There are no strange routing or firewall rules in place. And they are both set to respond to pings, I can ping them from outside. Our main IT guy is going to call our ISP on Monday, but I'm impatient, so does anyone have any ideas?

  Read the article

• Local IP address same as Google's external

  - by GRIGORE-TURBODISEL

  I'm exampling Google's IPs, but you get the idea. What happens if somebody configures a router's LAN address pool to range from 62.231.75.2 to 62.231.75.255, then his computer's IP address to 62.231.75.232 and someone else on the network tries to access Google? Or better off, is there any case in which someone in that network can, by merely attempting to access Google, accidentally bump into another computer on the network?

  Read the article

• IP NAT pool range

  - by hfranco

  When is it necessary to setup a pool of more than one address? So if I have this ip pool range: ip nat pool demo 72.32.11.65 72.32.11.66 netmask 255.255.255.252 What's the difference if I just have one address? ip nat pool demo 72.32.11.65 72.32.11.65 netmask 255.255.255.252

  Read the article

• setup PXE (i.e. DHCP + TFTP) server on MacOSX

  - by Albert

  What is the easiest way to setup an PXE server (i.e. a DHCP server + TFTP server) on MacOSX? Is there maybe some easy-to-use tool which just comes with both servers builtin? I have done that in the past but I remember that it took me several hours of editing some config files of tftpd (I think) and different versions of dhcpd, many trials and errors until I got it working (mostly). Now I have a fresh MacOSX installation and I want to avoid any complicated setup.

  Read the article

• Sharing internet connection with WDS

  - by cornjuliox

  Is it possible to share an internet connection through WDS? I'm on the very edge of a wireless network, the spot that I'm in maintains a stable 22% according to XP with the help of a parabolic reflector crafted from a cheap pie tin. I was thinking I could grab another wireless router, use WDS to bridge the this router with the other one and share the 'net connection through it thus giving me a little bit more freedom but when I tried it it didn't work. WDS looks like it bridged the networks just fine, but I couldn't access anything on the internet. Do I need to do anything special or is this just not possible?

  Read the article

• Users and Groups management on 7 Home Premium

  - by AviD

  Recently upgraded the home pc from XP pro, to Windows 7 Home Premium. I'm looking for a solution for a few things that seem to be missing from this edition... Since Local Users and Groups is blocked on Home Premium, I can't figure out how to manage groups, or even do anything even slightly advanced to users (basically, create/group/picture is it). net localgroup, net users, net etc dont seem to work - getting "system error 5". While I'm on the topic, I cant activate (what was once) "Local Security Policy"... Looking for any help, advice, or even a new direction cuz things is differ'nt on Winnows7... To clarify, I'm looking to do some of the following, which were simply back in XP-land: remote user only (i.e. no local logon) Grant special privileges for specific user grant access to e.g. C$ share for specific remote user create custom groups for users, to be able to separate privileges of say, my wife's from my kids define quite specifically what each user can do (beyond just standard users) Harden OS (hmm, i guess maybe what i'm looking for is security hardening guide for 7...?)

  Read the article

• Can't ping IPs for devices not part of Windows Domain

  - by GiddyUpHorsey

  I have a home network with a Trendnet wireless router and a Windows Domain. The DNS server is on a Windows 2000 Server and is configured to forward queries to DNS servers provided by the ISP. The router provides DHCP and is configured with the Windows 2000 Server as the DNS server. When I connect iPhones to the network over WiFi, the router can ping the iPhones through its browser based admin interface, but Windows machines that are part of the Windows Domain cannot. A laptop was connected to the network over WiFi that wasn't joined to the domain and it could see the iPhones. All machines either have a fixed or DHCP allocated IP on the 192.168.0.* subnet. How do I configure the DNS server or the Windows Domain so that Windows machines can see the iPhones?

  Read the article

• Unable to connect to server after a certain amount of time

  - by Troy

  I am a business FIOS subscriber with 5 static IPs. I have the following network setup: Verizon provided ONT Dlink switch Dell server running Ubuntu 12.04 with iptables enabled and a static IP address. The makes/models of hardware are: FIOS ONT Alcatel-Lucent I-211M-H ONT D-Link D-Link Web Smart Switch DES-1228P Server Dell Optiplex 755 (Ubuntu 12.04 Server) I have iptables running on the server with http, https and ssh ports open. I can connect to a website on the server from an external computer, but after a certain amount of time (mins to hours), I can no longer connect. All I have to do to re-enable connectivity is connect to the server via SSH from a computer INSIDE the network. I don't have to actually login, I just have to establish a connection. I can then access the website externally again. I did some googling and it seems some of verizon's equipment had an ARP bug where the ARP entries would expire after a certain time period, but those issues all seem to be from back in 2009 - 2010. I know the switch has an 'auto learning Mac address' feature, but I'm not sure if that could be the problem or not. Does anyone have any ideas or advice on how I can troubleshoot this? Thanks!

  Read the article

• How do I share a complete XP disk so it can be seen from a Windows 7 system? (To move all files to a

  - by Ian Ringrose

  This should be easier! (both computers can see the internet etc so I know the network it’s self is working) I have a normal home network with a Windows XP machine on it and the new Windows 7 (64 bit) machine. So I can transfer the files to the new Windows 7 machine, I wish to share the complete disk (and all files) from the Windows XP machine and access them from the Windows 7 machine. Is there a step by step set of instructions for doing this anywhere? So fare I have: put both computers into the same workgroup put the windows 7 machine into work network mode so it can see the XP machine in the work group shared the XP disk as read only But when I try to access a lot of the folders on the XP disks, I am told I am not allowed to access them. (I was not asked for any passwords by the windows 7 machine when I accessed the XP machine. The XP machine just has its default account with no password set on it) The XP machine runs XP home and hence has "simple file shairing" turn on. So it seems that even if I create a admin account (with password) and connect with that account, it still comes in as "guest" on the XP machine. Chooseing to share the folder I want access to rather then the top of the disk drive seems to work, but is a pain as I need to share each user's folder with a different share name. If the new computer was not a laptop, I would just plug the hard disk from the old machine into it, but being a laptop I don't have that option.

  Read the article

• Trouble in Team Viewer VPN Connection

  - by Sumit Pal

  I have completed initial vpn connection setup. It has connected. I have tested with ping and it is ok. My problem is, when I want to start file transfer in VPN it asks for username & password. So what is the user name? I have tried giving Computer-Name/User-Name. I have found my Computer Name by going to Control Panel/System/ & clicking 'Computer Name' tab & username from user accounts or it is shown when I login in windows account (Please correct me if the above procedure is wrong). But what is the password? I have tried giving the account password but it always give 'The username or password is incorrect.' My Question: How to find the username & password? For Information: a) I have Team Viewer 7 installed in one Windows XP PC & one Windows 8 PC. I like to create a secure connection between these two PCs. b) The two PCs are connected in the same local network via a router. Please ask if you need additional information.

  Read the article

• Where are Wireless Profiles stored in Ubuntu

  - by LonnieBest

  Where does Ubuntu store profiles that allow it to remember the credentials to private wireless networks that it has previously authenticate to and used? I just replaced my Uncle's hard drive with a new one and installed Ubuntu 10.04 on it (he had Ubuntu 9.10 on his old hard drive. He is at my house right now, and I want him to be able to access his private wireless network when he gets home. Usually, when I upgrade Ubuntu, I have his /home directory on another partition, so his wireless profile to his own network persists. However, right now, I'm trying to figure out which .folder I need to copy from his /home/user folder on the old hard drive, to the new hard drive, so that he will be able to have wireless Internet when he gets home. Does anyone know with certainty, exactly which folder I need to copy to the new hard drive to achieve this?

  Read the article

< Previous Page | 348 349 350 351 352 353 354 355 356 357 358 359  | Next Page >