Search Results

Search found 13151 results on 527 pages for 'performance counters'.

Page 354/527 | < Previous Page | 350 351 352 353 354 355 356 357 358 359 360 361  | Next Page >

• Is it wise to use SSHDs (Solid state hybrid drives) on a server?

  - by Seb

  I have a bunch of servers with very heavy I/O that currently use SATA3/SAS drives, but do suffer from I/O wait on the SATA drives, and I have just been alerted to the existence of SSHDs which cost the same for 1TB as the 1TB SATA drives that we currently use. However, previously (until Seagate shipped their first 3.5" SSHD in March) they seemed to be exclusively for Netbooks/Notebooks, which leads me to suspect they're not exactly built for the heavy I/O they'd be in for with my servers. So, would an SSHD give me a performance boost over my SATA3 drives in a heavy I/O environment (such as multiple very large high speed file transfers) or is it best to stick with SATA3 with I/O wait??

  Read the article

• RewriteRule in htaccess in subdirectory

  - by Jay

  Windows server, running Apache. In my Apache conf, I have AllowOverride None for the root of a site and then I have a subdirectory set to AllowOverride All: <Directory /> AllowOverride None </Directory> <Directory "/safe/"> AllowOverride All </Directory> However, when I try to set up a rewrite rule in the subdirectory's htaccess file, nothing happens, I just get a 404 page not found error. Example: RewriteEngine On RewriteRule (.*) /blah?test=$1 [R=302,NC,NE,L] Rwewriting URLs are working fine from the root via the Apache conf. I don't understand why the rule is ignored. I don't want to do the URL re-writing within the conf because for this case I may need to be changing the redirects constantly and don't want to reload the server every time a change is made. I also don't want to affect server performance by enabling htaccess files site-wide, just in the subdirectory I need it.

  Read the article

• Camtasia on remote computer?

  - by daughtkom

  I have a need to use one laptop for a live presentation (with projector, etc.), but record that presentation on another laptop -- similar to what I can do with Camtasia, only with the recording happening on another laptop. Is this possible? What do I need to do this? Some VGA device that goes between the presenting machine and the projector? Some USB device? My ideal requirements: The machines must be "standard" laptops (so I can't just add a new card to a desktop, etc.). I prefer a hardware solution, but cannot involve studio type equipment. I'd prefer not to install Camtasia (or similar) on the presenting machine for two reasons: licensing issues performance issues (sometimes the presentations are machine intensive and I don't want the recording software to interfere with the presentation) I'd appreciate any tips. Thanks.

  Read the article

• Copy & Paste Images Wiki functionality?

  - by Jakub

  I was discussing this with some coworkers, they would like a wiki, but are turned off by the need to constantly [browse] and [upload] files. They like the functionality of Lotus Notes that they can copy & paste screenshots (or crops etc) directly into Notes databases / libraries. But they are not fans of Lotus notes behond that (performance, etc,) Anyone work with a free (open source hopefully) wiki of documenting application that just allows copy & paste of text & image content? Would be great to have one internally installed that we could use for documentation without constantly uploading/attaching files. Not sure if I am asking for functionality that is not available in a browser.

  Read the article

• Bigger ProjectServer farm is performing worse

  - by MSPS DBA

  I am using Project Server 2007 sp3 with SharePoint 2007 sp3 and SQL Server 2008 r2. I have recently moved my farm from 2 servers (1 DB and 1 App/Web) to a very big farm having Many Servers, Clustered Database, Load Balancer, Powerful processors and Large RAM. This Farm has more than one Web Servers, Project App Servers, SharePoint App Servers and a separate Index Server. But the performance of Project Server in the new Farm has been downgraded. Views are taking even more time to load data and Project publishing time has also been increased. I am also facing deadlock problems which are causing the project server queue jobs to fail. Could anyone inform me that what would be the reason of this problem and what should be the starting point to look into the issue? Is it mainly because now the application server needs to communicate with other application servers which were not needed in the previous farm? Thanks!

  Read the article

• When is it time to buy a new hard drive, and what considerations go into buying a new hard drive?

  - by user1125620

  I've had my current hard drive for about 4-5 years now, and I've never had a problem with it before, but now it's making whirring noises. It's done this before and, last time, the noise did go away the next day, but I have accumulated quite a bit of information that I wouldn't want to lose on the drive. HD Tune Pro and Berlac Advisor both said the drive was healthy, and I wouldn't want to get a new one unless it was absolutely necessary or was going to show drastic performance improvements. My only knock against the drive would be that Visual Studio takes longer to load than I'd like it to. HD Tune Pro says the average read speed is 54.3MB/s. I'm not sure if that's good or bad, but it seems about average compared to similar drives on http://www.hdtune.com/testresults.html. Model #: WDC WD5000AAJS-22YFA0 So, should hard drives be replaced after a certain amount of time? Has mine reached that point? Would a new hard drive be any faster?

  Read the article

• What is the Optimal Server Configuration for Split-Path Testing?

  - by doug

  I am far from an expert on Apache or any server for that matter, so i apologize if this question is poorly worded, which it likely is. We have always relied on a vendor for split-path testing (aka "AB Testing"). If you're not familiar with that term, it's a form of marketing research in which you slightly modify one of your web pages (usually one nearest the point of conversion), say for instance, by changing the position of the "Buy Now" button or its color/contrast/texture, then serving one of those two pages to a given user based on random selection. By doing split-path testing ourselves, I suspect we can do it far more cheaply and increase cycle times as well. What is the optimal set-up for these tests? "Optimal" is based on the following criteria: how quickly/easily new tests can be set-up and put online; and minimal disruption to overall site performance

  Read the article

• OPTIONS * HTTP/1.0 APACHE

  - by Abby E

  I been noticing a lot lately in my /server-status the OPTIONS * HTTP/1.0 has been coming up lately a lot. I'm running Ubuntu 12.04 with the latest apache/php/MySQL. I'm not sure what they're for but I would like to see if it would effect performance by some how turning it off. I host some stuff that is accessed a lot that uses PHP/MySQL (600 rps). I'm not sure what it's there for but I do see the local 127.0.0.1 IP, so I assume it's something running local. What is it? How do your turn it off? If turned off how would it effect performance? The list below is a small example of it. (127.0.0.1 REMOVED.(null) hostname has been removed) 211-0 - 0/0/1035 . 24.28 240189 0 0.0 0.00 0.18 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 212-0 - 0/0/51274 . 677.97 202960 0 0.0 0.00 8.99 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 213-0 - 0/0/419 . 11.85 240424 0 0.0 0.00 0.07 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 214-0 - 0/0/240 . 7.96 240552 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 215-0 - 0/0/309 . 9.29 240492 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 216-0 - 0/0/98510 . 1258.25 177391 0 0.0 0.00 17.29 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 217-0 - 0/0/338 . 10.18 240464 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 218-0 - 0/0/345 . 10.27 240469 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 219-0 - 0/0/118538 . 1507.99 168914 0 0.0 0.00 20.80 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 220-0 - 0/0/98452 . 1259.10 177412 0 0.0 0.00 17.29 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 221-0 - 0/0/384 . 10.84 240453 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 222-0 - 0/0/331 . 10.03 240477 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 223-0 - 0/0/314 . 9.04 240493 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 224-0 - 0/0/75193 . 975.24 188845 0 0.0 0.00 13.18 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 225-0 - 0/0/362 . 10.62 240457 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 226-0 - 0/0/125773 . 1593.26 165647 0 0.0 0.00 22.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 227-0 - 0/0/82541 . 1063.89 185092 0 0.0 0.00 14.48 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 228-0 - 0/0/409 . 11.50 240436 0 0.0 0.00 0.07 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 229-0 - 0/0/219 . 7.38 240581 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 230-0 - 0/0/357 . 10.48 240458 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 231-0 - 0/0/469 . 12.39 240411 0 0.0 0.00 0.08 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 232-0 - 0/0/394 . 11.32 240445 0 0.0 0.00 0.07 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 233-0 - 0/0/276 . 9.00 240510 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 234-0 - 0/0/245 . 8.51 240536 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 235-0 - 0/0/215 . 7.45 240555 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 236-0 - 0/0/370 . 11.00 240443 0 0.0 0.00 0.06 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 237-0 - 0/0/400 . 10.96 240446 0 0.0 0.00 0.07 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 238-0 - 0/0/266 . 8.51 240531 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 239-0 - 0/0/304 . 9.81 240499 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 240-0 - 0/0/446 . 12.47 240421 0 0.0 0.00 0.08 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 241-0 - 0/0/19741 . 282.90 230130 0 0.0 0.00 3.45 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 242-0 - 0/0/98503 . 1259.43 177404 0 0.0 0.00 17.28 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 243-0 - 0/0/251 . 7.93 240551 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 244-0 - 0/0/273 . 8.42 240534 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 245-0 - 0/0/118485 . 1508.14 168950 0 0.0 0.00 20.79 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 246-0 - 0/0/294 . 9.35 240509 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 247-0 - 0/0/413 . 12.34 240437 0 0.0 0.00 0.07 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 248-0 - 0/0/258 . 8.55 240529 0 0.0 0.00 0.04 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0 249-0 - 0/0/303 . 9.77 240485 0 0.0 0.00 0.05 127.0.0.1 REMOVED.(null) OPTIONS * HTTP/1.0

  Read the article

• What does motherboard RAM slot colors mean?

  - by totymedli

  I always saw that the motherboard RAM slots are colored in pairs, but never know what does it means. I just put the 2 RAM in, and after a few tries it always worked. But after I tried to install a third one it always throws me a blue screen of death. Is there an order how should I install RAM to the borad? What does the colors mean? Does they indicate performance boost opportunity or are they just a guide for installation?

  Read the article

• Apple Airport Extreme Wireless Card M8881 Connectivity Issue

  - by Carlosfocker

  I bought a Apple Airport Extreme Wireless Card M8881 with the antenna for my old Power Mac G5 1.6 Ghz. The computer is running OS X 10.4. The card works and I can connect to my dlink 802.11g wireless router using WPA2/AES encryption. The problem is that the connection has intermittent connectivity issues. When the issue occurs the signal bars for the connection drop to one or two bars and the performance of the connection suffers greatly. The computer isn't far from the wireless router. I have a laptop at the desk where the mac is and it does not have any issues. I'm not sure what it might be? Updated drivers? Firmware? Let me know if I forgot any important information.

  Read the article

• misaligned raid partition in Ubuntu 10.04

  - by Linux Jedi

  I attached two identical hard drives to my linux machine. Then using gparted I formated the first 1024 mb at the beginning of each drive as linux swap space. Then I went into system-administration-disk utility. In there I went to file-create-RAID array. I selected the remaining space in each of the two identical hard drives and created a striped raid array. After the array was created, a warning message appeared. It said "The partition is misaligned by 522240 bytes. This may result in very poor performance. Repartitioning is suggested." What do I do now? As far as I can tell, the partitions are identical.

  Read the article

• How do you explain ethernet cable problems to non networking people?

  - by Bryan McLemore

  We've recently been doing a large network migration in our datacenter. We've had a few cables in this start to deliver really bad pings (in excess of 500ms on a LAN) before they could be replaced. The cables we were replacing weren't made the best. They where all hand made and the runs were so short on some of them that the bend radius was definitely too tight. Some of them ran in bundles right in front of the heat exhaust of the power supplies. The cables were running ok until we started pulling the ones surrounding them out. Then a few started having the problem I mentioned above degrading performance and causing reliability issues. I'm trying to figure out the best way to explain this to non networking people. Is there any documentation that people could recommend or other methods?

  Read the article

• Windows script to create directories of 3,000 files

  - by uhpl1

  We have some email archiving that is dumping all the emails into a directory. Because of some performance reasons with the server, I want to setup an automated task that will run a script once a day and if there is more than 3,000 (or whatever number) of files in the main directory, create a new directory with the date and move all the main directory files into it. I'm sure someone has already written something similar, so if anyone could point me at it that would be great. Batch file or Powershell would both be fine.

  Read the article

• Apache CPU usage stays at 100% even when there are no requests

  - by Leirith

  Hi, I've been running the Apache HTTP server benchmarking tool (ab) on my new Apache server to test performance. I noticed that with a command like the following: ab -n 100000 -c 1000 http://www.mysite.com/ The CPU is used 100% by the apache2 processes during the testing. When the test concludes, usually with the following error just before the last requests are made: apr_poll: The timeout specified has expired (70007) Total of 99960 requests completed the CPU usage remains at 100%, and it's all being consumed by apache. I am using the worker MPM with and running PHP with mod_fcgid. Any advice as to why this is or what can be done to stop it would be appreciated.

  Read the article

• Why are there so few Wireless N Dual Band adapter PCI cards, only USB adapters instead?

  - by daiphoenix

  There has been several Wireless N Dual Band routers/APs out in the market for quite some time now, and there are several Wireless N Dual Band USB adapters out there. But as for PCI/PCI-X card adapters, there seems to be only one (the Linksys WMP600N). Why is that? I find it very strange. Is it because the USB adapters are easier to install, and can be used on multiple computers? But if so, why isn't it the same case with single band (2.4 Ghz) wireless N adapters? Because for these ones there as many PCI card adapters as there are USB adapters. Also, can the USB adapters, despite the lack of external antenna, offer the same level of performance as a card with external antennas?

  Read the article

• How do I fix "Setup did not find any hard disk drives installed in your computer" error during Win XP Pro install?

  - by CT.

  I just bought a nettop. It came with WinXP Home. I first installed Win 7 on it. I wasn't that happy with the performance so I decided to go back to XP. I am using an external dvd drive and a Win XP Pro disc. I boot from the dvd drive and during the install get this error: Setup did not find any hard disk drives installed in your computer. Make sure any hard disk drives are powered on and properly connected to your computer, and that any disk-related hardware configuration is correct. This may involve running a manufacturer-supplied diagnostic or setup program. Setup cannot continue. To quit Setup, press F3. This is the nettop in question: http://www.newegg.com/Product/Product.aspx?Item=N82E16883103228

  Read the article

• ESXi with non-headless VM

  - by Mike

  I'm going to receive a Xeon Server/Workstation soon and I was thinking about installing ESXi to host some server applications that I want (ex: SVN server, Web server, media server, etc). Most of these will be headless VM's. My question is: on top of all these headless VM's, is it possible for ESXi to have another VM that would be non-headless (so that it will output video through the VGA/DVI port)? Or are all VM's within ESXi only accessible through remote connections? I'll be using this non-headless VM like a regular workstation: browsing, development, media, gaming maybe. The other alternative I was thinking about is to install a very lightweight operating system and have the headless VM's running in Virtualbox. If it is possible to have have a non-headless VM, what would be the performance compared to a regular workstation? Noticeable or not when gaming?

  Read the article

• What are my X client options for MS Windows?

  - by Nick Bolton

  I need to connect to a headless X Windows server (running on Ubuntu) from my MS Windows 7 computer over a 100 Mbit network. I could use VNC (or any other remote viewer) but the 3D graphics performance would be lousy I imagine. I used to have it hooked up to a monitor, but that's broken now and I can't afford a new one. A friend advised that I could try and use an X client, and that the 3D graphics wont suffer too much over 100 Mbit. Cygwin seems to be an option, but I was wondering if there were any more lightweight options.

  Read the article

• Using a CF card as an IDE HDD

  - by dartacus

  I have an old Sony laptop (Vaio TR1-MP) that I like. The HDD has died and since it's a hard-to-find 1.8" IDE hard drive I'm considering buying one of those little CF card adaptors and a 16gb CF card. The total cost of that is about £30 and replacement HDDs for this model are far pricier. Has anyone replaced their HDD with a CF card in this way, and, crucially, is the performance utterly horrible afterwards? ;-) I've seen a couple of threads which hint it's possible but the advice eventually given was just to buy a SSD, but I'm not even sure if its possible to get a 1.8" SSD with an IDE connector that'll fit my laptop. (I freely admit that the most sensible thing to do would be to bin it and just buy a cheap netbook which would be smaller, faster and lighter than the sony, but it does have a very nice widescreen display and dammit I just like it !) Thanks, G

  Read the article

• Need hard disk recommendation for linux home server.

  - by neotracker

  Hello, I'm planing to build a little linux homeserver. It will mainly be used for storage and maybe as an media pc. I plan to build a software raid5 with 4 1.5TB or 2TB hard drives. I already decided to use the Western Digital Caviar Green 1.5 TB drive, but then I read about some problems with the WD green series about many drives failing and that they are not recommended for raid anyway. Of course, I couldn't find much facts on the issues so I thought I just ask here ;-) What hard drives would you recommended for a software raid5 setup? As I only need it for storage, the whole thing doesn't have to be too fast. So I prefer a cheap price and silence to great performance.

  Read the article

• Which modules can be disabled in apache2.4 on windows

  - by j0h

  I have an Apache 2.4 webserver running on Windows. I am looking into system hardening and the config file httpd.conf. There are numerous load modules and I am wondering which modules I can safely disable for performance and / or security improvements. Some examples of things I would think I can disable are: LoadModule cgi_module others like LoadModule rewrite_module LoadModule version_module LoadModule proxy_module LoadModule setenvif_module I am not so sure they can be disabled. I am running php5 as a scripting engine, with no databases, and that is it. My loaded modules are: core mod_win32 mpm_winnt http_core mod_so mod_access_compat mod_actions mod_alias mod_allowmethods mod_asis mod_auth_basic mod_authn_core mod_authn_file mod_authz_core mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_dav_lock mod_dir mod_env mod_headers mod_include mod_info mod_isapi mod_log_config mod_cache_disk mod_mime mod_negotiation mod_proxy mod_proxy_ajp mod_rewrite mod_setenvif mod_socache_shmcb mod_ssl mod_status mod_version mod_php5

  Read the article

• How do I find the source of soft page faults?

  - by David Robison

  I have Windows 7 x64 computer that according to Performance Monitor has 70,000 page faults / second when idling. That's seems like a lot to me (every other computer I check has basically 0 page faults / second when idling). If I use Resource Monitor or Process Explorer to check hard faults, I see that they are basically 0. So all the page faults are soft. Normally, soft page faults are not a problem, but I suspect they might be causing issues for this computer given there are so many. I would like to identify what programs are causing the soft faults. Are there any tools that exist the display the number of soft page faults for each process?

  Read the article

• Just how slow should my VPN be?

  - by David Heggie

  I have a VPN setup between a remote office with 2 ADSL connections (8Mb downstream, 512Kb upstream) and a main office with a 10Mb EFM connection (10Mb both up and down). The VPN is an IPSec connection using a DrayTek 2930 router for the ADSL and a DrayTek 3200 router at the EFM end. However, I'm unable to get speeds over this connection (tested with iperf) of anything over 600Kb or so down from the main office (traffic will pretty much always be from the main office to the remote office) Whilst I realise that there is an overhead and I'm never going to get the "full" bandwidth available over this VPN, I'd like to think that there's something I should be looking at that may help improve it. I've tried using the DrayTek's built-in "VPN Trunking" features which are supposed to load-balance connections, but this doesn't seem to improve matters much. I guess my question is - is this the kind of performance I should expect from this kind of setup and I'll just have to live with it, or should I be able to squeeze something more out of it through some VPN magic?

  Read the article

• Video problem with Windows 7 Games

  - by Jordan 1GT

  I have a Dell xps M1330 which originally ran Vista, but I upgraded to Windows 7. When I try to run a Win 7 game like spider solitaire I receive the following message: "The game is running in software rendering mode. Hardware acceleration is either disabled or not supported by your video card driver which could slow down game performance. Make sure you have the latest video card driver installed and that hardware acceleration is turned on." I confirmed that hardware acceleration is turned on. When I go to Dell's site, I'm told there is no later video driver. When I run the game it runs very choppy. I wouldn't care, but I loaded a .pptx file which is doing strange things in normal view and I suspect may be related to the same video problem. Any ideas?

  Read the article

• Cached css/javascript files on Sun Java System Web Server

  - by Derp

  I'm doing front-end web development in a Solaris 10 / Sun Java System Web Server 7.0U2 environment. I have noticed that changes to static css or javascript files often do not take effect immediately, whereas changes to static html files always do. My best guess is that a default setting in the web server causes it to cache certain file types in order to provide reasonable performance out of the box. I don't have the admin server running--I'll need to edit the config files by hand. What change(s) can I make so that all of my css and javascript edits take effect immediately? Thanks!

  Read the article

< Previous Page | 350 351 352 353 354 355 356 357 358 359 360 361  | Next Page >