Search Results

Search found 59849 results on 2394 pages for 'windows embedded 7'.

Page 356/2394 | < Previous Page | 352 353 354 355 356 357 358 359 360 361 362 363  | Next Page >

• IBM x226 server with Windows 2003 freezing and showing one HDD degraded

  - by Zvonko Telefonko

  We have an IBM x226 server with Windows 2003 running on it. For weeks it's been very slow and it freezes at least once each day. At the boot it show message "degraded" for one HDD and optimal for other HDDs. We have 4 HDDs in it set up in Raid 1. HDD 1 - HDD 2, HDD 3 - HDD4. It seems that HDD2 is the one who is causing problems (showing degraded status). There's an amber led blinking on it together with the green one. We installed ServerRAID manager downloaded from IBM and it gave us option for "rebuild". But the server froze at some point and now it's rebuilding from start again. I've done some Googling and it says that it could be to failing HDD or some cache battery. How can we verify what is the cause of this?

  Read the article

• IPv6 6to4 on Windows Server

  - by Graham Wager

  I'm looking for a relatively simple guide to setting up an IPv6 tunnel properly. This network currently has a server (Windows Server 2008R2) running RRAS that establishes connectivity to the internet using a demand-dial PPPoE connection and handles the NAT. It also hosts a DNS server and DHCP. My ISP does not support IPv6, but I have a static IPv4 address. I've read about 6to4 and signed up at tunnelbroker.net, but quickly felt out of my depth. How do I configure my network to use it, and how I should configure my DHCP server with regards to IPv6 addresses?

  Read the article

• What Windows licenses are required to run additional terminal service sessions

  - by John P

  We need to build out a server running Windows 2008 R2 Standard that can allow up to 10 simultaneous RDP/Terminal Services connections and I'm a little confused about how the CAL licenses work. From one source I was told I needed 10 "server CALs" and an additional 10 "RDP CALs" (total of 20 CALs). From another, I was told I just needed the 10 "RDP CALs", which implicitly came with the server CAL. The Microsoft licensing website (http://www.microsoft.com/windowsserver2008/en/us/licensing-rds.aspx) seems to support scenario #1, but it is still not real clear what those server CALs are needed for. Also, can we use the 2 "built-in" RDP clients, meaning we only need to purchase 8 CALs to reach a total of 10?

  Read the article

• Windows 7 Bootcamp to see data doubler SATA SSD in Optical Bay Connector

  - by bumble_bee_tuna

  Hi I purchased a OWC data doubler http://eshop.macsales.com/item/OWC/DDAMBS0GB/ ... Long story short it lets you add a second HD to your macbook pro in place of the cd/dvd drive (which is useless anyway, impossible to get stuff out when stuck). My current setup is 600gb intel SSD bootdrive 100gb partition for OSX / 500gb for Windows 7 Prof from Bootcamp (use 99 % of time). My desire is to have a second 300gb SSD to run disk intensive VM's off of. So I added a second 300gb intel SSD (again, NO desire to boot off of) on the sata optical port. I can see the drive no problem if I boot in to OSX, however, can't see it in disk management on Win7 ??? Any ideas similar experience ... Funny thing is I can see it in "Device Manager Disk Drivers" but not Disk Management ??? Also no I don't want to use Fusion/Parallels this is a waste of resources for me.

  Read the article

• Windows Home Server Passwords Do Not Match

  - by Ben Fulton

  I have a Windows Home Server that chunks along just fine most of the time. I've never bothered to put it on a UPS and so it's vulnerable to power outages that happen a few times a year. This most recent time, it came back and seemed to be fine, but whenever I try to access a shared folder I get "Passwords do not match". They matched before the power went out, and I couldn't update the WHS password since I apparently didn't know the old one. How do I fix this? (I asked this on ServerFault and they recommended it be asked here instead)

  Read the article

• Do most "normal" people use metro or desktop in Windows 8

  - by ihateapps

  Just curious since I don't fit the definition of a "normal" computer user nor have my friends or relatives upgraded to Windows 8 yet. Are most people in the "wild" (i.e. the "guy in starbucks" or "your friend who works as an auto tech". not you since you are on SU) using metro apps regularly to the point where the desktop is pointless or are they sticking with the desktop? I've gotten mixed statistics from Google. I'm asking for your personal anecdotal opinion based on what you notice in the wild.

  Read the article

• Windows Server 2008 R2 backup includes volume with MSSQL data

  - by J F

  I'm using wbadmin to schedule image backup every night on a Windows Server 2008 R2 Standard server. Ever since installing MS-SQL 2008 Express R2, wbadmin wants to also backup the volume where the MS-SQL data files are located (L:). I'm using -allCritical to make sure bare metal restore will work. command-line: wbadmin start backup -backupTarget:\\myserver\backup$\myserver\%DATE% -include:C: -allCritical -quiet I don't want to do this, because I'm backing up MS-SQL manually elsewhere. It worked just fine only taking C: before I installed MS-SQL.

  Read the article

• How do I minor upgrade MySQL on Windows?

  - by TruMan1

  I currently have MySQL 5.1.35 installed on a Windows 2008 server via the MSI installer. I need to upgrade to the latest 5.1.44 to fix a bug, but docs were not clear on how to do this. I ran the MSI installer, but it did not give me any upgrade option so I quit it. I am weary because it's a production machine with many PHP websites running on it. Also, my data directory is not the default one, it's kept on another partition. How can I upgrade it? Thanks for any help.

  Read the article

• Windows Media Player 11 Not Detecting Autoplaylists

  - by tuna

  Every time I open Windows Media Player it fails to detect my autoplaylists stored in <my music library dir>\Playlists. This appears to lead to sync problems since I (exclusively) use autoplaylists to sync music to my mobile. As WMP 11 fails to find the any sync autoplaylists it infuriatingly seems to decide that I want no music at all on my phone and proceeds to delete all my music off my phone. I guess these are two seperate problems but it seems to me they are related. If anyone can shed any light on a fix, that would be much appreciated. Many thanks

  Read the article

• Windows Server 2008 R2 stuck at System Recovery Options

  - by Magnus

  One of my Windows Server 2008 R2 server has started to go into System Recovery Options at reboot. I have tried to let it go through a System Image Recovery, which it says completes successfully. But after reboot it again wants to do a system recovery. Safe mode doesn't work; it still wants to do a system recovery. Putting in the install DVD trying to do a repair actually brings up the very same System Revoery dialog again. Nothing has changed configuration wise. Any ideas?

  Read the article

• Windows Server 2008 R2 stuck at System Recovery Options

  - by Magnus

  My Windows Server 2008 R2 has started to go into System Recovery Options at reboot. I have tried to let it go through a System Image Recovery, which it says completes successfully. But after reboot it again wants to do a system recovery. Safe mode doesn't work; it still wants to do a system recovery. Putting in the install DVD trying to do a repair actually brings up the very same System Revoery dialog again. Nothing has changed configuration wise. Any ideas?

  Read the article

• Windows 2008 VPS always crashes when out of disk space

  - by Pickels

  Hello, I am renting a Windows server 2008 dc SP2 VPS for hosting my Asp.Net projects. Now for the second time this month my VPS ran out of disk space. The first time it was a log file that got to big and yesterday it was my mistake for uploading a website without noticing the lack of space on my VPS. Now the side effect this has is that my VPS corrupts some files when trying to write them. Last time it was Plesk that stopped working yesterday it was IIS. So I was wondering is this normal behavior? I called my service provider to ask if they could restore a back-up and to ask if this is normal and they ensured me it was. I am not trying to blame them and I know it's mostly my fault for not monitoring my VPS better or for not setting better defaults.

  Read the article

• Changing Administrator password on a Windows 2008 web server

  - by Nick

  I've just taken over the administration of a Windows 2008 web server from a previous employee on a temporary basis. I need to change the Admin password as soon as I can but I've noticed that quite a few of the services also run under this account. So: Is there a quick way to find out which services will be affected by me changing the password or is it a question of going down the list? It doesn't seem right to me that the Admin account is used in this manner; should I create a different account for these services, or is using the Admin a/c standard practice? I realize everyone's servers / networks are set up differently, but are there any other items I should be aware of when changing the Admin password? Thanks

  Read the article

• suggestions for migrating a windows 7 install to a new 4K sector disk

  - by myCubeIsMyCell

  Hi, I'm looking to upgrade the disk on a windows 7 box to a new larger drive. In the past for such migrations I'd just hook both drives up and use a linux boot disk and use dd to copy from one disk to the next... boot up the new drive & expand the partition. The drive I just purchased however is a western digital using 4k sectors... not sure if there'd be any complications using my old method moving from a 512b sector drive. Current plan is to try the migration by doing a win7 system image backup to an external drive... then restore the image to the new drive via system restore boot disk. Any suggestions or recommendations on how to best complete this migration would be greatly appreciated. Thanks!

  Read the article

• How to create NTFS partition in Linux to install Windows 7 from USB?

  - by Michal Stefanow

  I messed up with my computer and need help. Generally: install Windows 7 from USB. Problem: "setup was unable to create a new system partition" When first attempt to install Windows 7 failed I tried Linux live USB, installed distro to HDD, and erased all the existing partitions. Current state (fdisk -l): [writing from other computer so no copy and paste] /dev/sda1 305GB Linux /dev/sda2 7GB Extended /dev/sda5 7GB Linux Swam / Solaris To create a new, NTFS partition: fdisk /dev/sda n (for new) p (for primary) 3 (for partintion number) "No free sectors available" All the HDD was formatted couple of minutes before so there is a lot of free space but how to resize a parition? I cannot find an option for resizing in man fdisk. Some people say I should use gparted but my distro doesn't not contain this package. And my distro doesn't support wireless drivers so I have serious problems with downloading stuff. I tried also using cfdisk but any command results in: "cfdisk bad primary partition 1 partition ends in the final partial cylinder" I tried also removing partition 1 and then creating a new one (so there is no "no free sectors"). I'm receiving a warning: "Re-reading the partition table failed with error 16: Device or resource busy. The kernel still uses the old table. The new table will be used at the next reboot." After restating: "grub rescue, no known filesystem" It may indicate that some changes have been made BUT when running Windows 7 installed some another error: "Windows cannot be installed to Disk 0 Partition 1" More detailed: "Windows cannot be installed to this hard disk space. Windows must be installed to a partition formatted as NTFS." So formatting drive using Windows 7 installer BUT this time yet another error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information" Apparently I cannot access logs (how?) and I am back to drawing board with my live USB (this time showing partition as HPFS/NTFS). Any suggestions how to install Windows 7? Should I reinstall Linux to HDD, erase existing partitions once again, and use Parted rather than gparted (parted is included in the distro). Or maybe should I create another bootable USB such as PartedMagic to painlessly create partitions? I just want to install Windows 7 from USB, my laptop is semi-operational and I am ready to receive some help regarding fdisk and creating NTFS partitions. UPDATE: I did as suggested (removed all the partitions) and tried to install in unallocated space. Tried to create a new partition and format it. Same error: "setup was unable to create a new system partition" Came to the conclusion it may have something to do with TrueCrypt I have recently installed. Right now trying to FIX MBR (as I haven't got possibility to create rescue disc without optical drive)

  Read the article

• How can I get Windows 7 to remember program windows size and position?

  - by Ben

  I can open Outlook and it fills about half of the screen. I then maximize it to read some mail and then minimize it to do some other work. When I click on it again in the taskbar, it is back to the original size that it opened at. I have tried Ctrl-close and Ctrl-maximize but neither seems to work. This also happens with Explorer windows, AutoCAD, Revit, and other programs that I work with. Shouldn't a minimize and a maximize bring the window back to the last size and position?

  Read the article

• Problem opening files with Gvim on Windows 7

  - by Oscar Duignan

  Just installed gvim on windows 7 for the first time, and I'm having a problem opening some files. When I open files vim seems to flash up a cmd window for a few second before closing it (too quickly to make out the contents,) and I end up with a C:/Program folder, and a /Files/vim/vimfiles/doc/ in the directory of the file I just opened. I can see it's trying to access C:/Program Files/vim/vimfiles/doc, which is where vim is installed, however it's choking on the space, and I'm not familiar enough with gvim to work out why. Any and all ideas are greatly appreciated.

  Read the article

• How to access Windows Registry from DOS

  - by SEARAS

  How to access Windows Registry from DOS? I need to access registry from DOS, while I boot from DOS bootable disk. I've searched all the internet, and found only Offline NT Password and Registry Editor, which can not be used in DOS, as I understand. Also I've found RegView (from many mirrors), which isn't working too (I've tried many instructions). Is there any easy-in-usage tool, like reg.exe, which is able to load registry hives, so that I can change registry values?? Or any working instructions ?? Note: I already have a bootable drive, which can read/write to NTFS drives. Thanks in advance!

  Read the article

• Timeouts when connecting to SQL Server since installing SP1 for Windows 7

  - by Julien

  Hi, I just installed SP1 for windows 7 and I have severe performance degradation when connecting to SQL Server 2005 since then. Establishing connection takes more than 30 seconds while it's instantaneous on another computer. Firewall is disabled and I didn't make any change to the configuration. It happens both when trying to connect with a hostname and with an ip address. Everything else seems to be fine (for instance, I'm have no issue connecting to other computers with remote desktop) What can cause such a problem? Thanks in advance! Edit : uninstalling the SP1 solves the issue instantly.

  Read the article

• Windows 7 taskbar items not grouping properly

  - by Joel in Gö

  I don't understand the Windows 7 taskbar behaviour. For some programs it will not group the running instances, or will groups some of them but not all. I have set taskbar items to "always combine", but this has not helped. It seems to possibly be two issues: with an app that has a different taskbar icon when running than for its launcher; and for VisualStudio, when starting by double clicking a project it groups separately from when starting the IDE from the .exe. Is there any way to force the items to combine? I quite like the Win7 taskbar, and would like it to work consistently...

  Read the article

• Changing the passphrase of a private key in Windows

  - by janos

  I have a private key in Windows, created by puttygen.exe. I used default options to save it, the tool automatically gave it a .ppk extension, and it looks like this: PuTTY-User-Key-File-2: ssh-rsa Encryption: none Comment: rsa-key-20130627 Public-Lines: 4 AAAAB3NzaC1yc2EAAAABJQAAAIBnvvAhyMs4rdlQd4OdajDw4jIPi6vIjrWjt4l4 5C3wHOSxyQQdtSA8XT3K0rSBnNtZRJTb5mfix67qQe3pHCTMSNsYIaBi8xQJHZRa RxdY+1VtGnSlEma8KO2We9eDNCGiwrRTUzqvTiGCnzU0pF1MXxu3ObISJcpqv+sQ 1GB0cw== Private-Lines: 8 AAAA.......... Private-MAC: XXXXXXXXX Now I need to change the passphrase, and reading from the docs it seemed simple enough: puttygen.exe -P key.ppk But this pops up a window with this error: PuTTYgen Error: Couldn't load private key (unable to open file) I also tried to change the passphrase using ssh-keygen that comes with Git Bash: ssh-keygen.exe -p -f key.ppk It asks for my old passphrase, but then it gives me the error Bad passphrase. Which is not true, because I can add the key in pageant.exe, and I am not mistyping the passphrase... Anything else I can try to change or drop the passphrase?

  Read the article

• Adding a Windows Server 2012 Essentials server to an existing domain, without migrating the AD

  - by TiernanO

  I have an existing Active Directory in house, a mix between a Win2K8R2 and Win2K3 domain, and i would like to test out Windows Server 2012 Essentials BETA on the network. When walking though the install, it gives me the option of a new domain, or migrating from an existing domain. when clicking existing, it tells me i can only have one SBS server running on a domain at a time... So, i dont have any existing SBS servers in house (both are full standard or enterprise editions) but i do plan on keeping at least one of these extra servers running... So, how do i get a 2012 Essentials server to join a domain, and not migrate the existing domain? or if i do migrate, can i still get one of the other boxes to act as secondary controllers?

  Read the article

• Windows application shortcut icon cannot be removed

  - by Claudiu Constantin

  I recently installed an application on my Windows 7 desktop. After the install this application created a strange icon on my desktop which cannot be removed/deleted or renamed. I find this quite intrusive and I keep wondering if this is a normal/legal case... Is an application allowed to do this? I don't remember having an option to allow this "Chuck Norris" icon on my desktop. Any information on this will be highly appreciated. Edit: What this icon does is when you drag over a file it applies some "deep removal" of it. It's context menu is limited to "Open" (which does nothing) and "Create shortcut"

  Read the article

• Eventlog entry for allowed connection in Windows Firewall

  - by Jaap

  I was seeing a lot of entries in the eventlog: The Windows Filtering Platform has permitted a connection. Application Information: Process ID: 4 Application Name: System Network Information: Direction: Inbound Source Address: 10.xxx.xxx.xxx Source Port: 80 Destination Address: 10.xxx.xxx.xxx Destination Port: 31773 Protocol: 6 Filter Information: Filter Run-Time ID: 67903 Layer Name: Receive/Accept Layer Run-Time ID: 44 We have a loadbalancer which checks every second to see if the application is still running (a health check). The logs contain large amounts of this kind of entries, which makes the Event Viewer slow and it's difficult to find the more interesting logs. How do I make sure these messages don't end up in the event logs?

  Read the article

• Windows 7 freezing unexpectedly

  - by Thomas Deutsch

  I have a Windows 7 computer here, which is freezing between 2 times a day and 1 time every second day. I see no problem, no special drivers, no special Apps are open, no encryption or something like that. Apps usually open then are Firefox, Thunderbird, Eclipse and maybe Office. Computer is just freezing. No Reboot, no shutdown, no bluescreen and no error. User has to hardreset it. Eventlog shows me an kernel error saying it has been unexpected rebooted due to an fatal error, but no statement about what kind of error happended. Anyone an idea what it can be? Chkdisk should be ok (currently, I run it a second time).

  Read the article

< Previous Page | 352 353 354 355 356 357 358 359 360 361 362 363  | Next Page >