Search Results

Search found 7731 results on 310 pages for 'exit failure'.

Page 36/310 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

• Hard drive not detected after installing the Operating System

  - by Eka Anggraini

  After I failed to install SUSE Linux 10.0, I want to go back to the windows operating system again. but when I want to install windows, my hard drive is not detected, whereas in the BIOS in the detection / known. I was dizzy, his mistake about it. Where is. I was looking for, my problem is named after the Blue Screen of Death (BSOD) that is an error message from windows to prevent further damage, but with various types of error messages, one of them as I have *** STOP: 0X0000007B (0XF896A524, 0XC0000034, 0X00000000, 0X00000000) I do not know, where the system is broken. but why hard drive is not known ... at the time of going to re-install?

  Read the article

• Is U.P.S necessary to have for PC?

  - by Jitendra vyas

  otherwise can my PC component ( Monitor, Motherboard, RAM, HDD, CPU, SMPS) get damage dues to suddenly power gone and come and due to power fluctuation. or it's only needed to shut down windows Properly. Can i face both Hardware and Software problems without UPS?

  Read the article

• Dell Vostro Desktop error

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Power Outage Interrupted Upgrade from Windows Vista Ultimate to 7 Ultimate, Reverted to Vista, Now Vista is failing... What Next?

  - by tednewk

  I was in the midst of what seemed to be a successful upgrade from Vista Ultimate to 7 Ultimate when there was a brief blackout. The upgrade failed and Windows reverted back to Vista. Now Vista is very slow to boot, has problems waking back-up from inactivity and quickly loses it's wireless connection. The wake-up problem manifests itself as the mouse is clearly shown on a black screen but I have no access to the Desktop or Taskbar or Explorer. Even Alt-Ctrl-Delete doesn't seem to work. No task menu, no reboot. Hitting the reset button reboots the machine with the usual Black Screen warnings offering Safe Mode. I tried to do a system restore to a point before the upgrade. That didn't seem to work. My guess is that my system is a mutant with parts of Vista and parts of 7 crashing each other. I would like avoid a clean install if at all possible to avoid reinstalling other software. What should I try now? My thoughts are: My a system back-up to lock the computer in place Trying a second 7 upgrade If that appears to be working make another back-up If not reload back-up and try a repairing Vista from DVD. If that appears to work make another back-up, let system stablize about a week then try 7 install again If that doesn't work are there any other options to try before settling for a clean install? Another complication, I am doing this by "remote control". I'm traveling with my job and I'll be talking my son through it over the phone. (Kind of like the landing the 747 cliche from all the 70's adventure shows!) So is there a way of simplifying the steps? Thanks Ted

  Read the article

• Computer not POSTing "randomly"?

  - by smoth190

  I have a custom built PC that is exhibiting some...odd... behavior, something I've never seen before. It was working fine one day, and the next day, it wouldn't start. Seeing as I wanted an upgrade anyway, I purchased a new motherboard that was compatible with all my parts. While replacing the motherboard, I accidentally damaged the CPU. Well, I wanted a new one anyway... so I got a new one. Seeing as I was replacing a ton of parts already, I bought a new PSU because the old one was super loud. When I slapped it all together, it starts up, lights, fans, drives, they all start. But I get no display from the monitor. No beeps, which I believe means it doesn't POST. I figured it was the RAM, because after removing the sound card and graphics card, there was nothing else that I hadn't replaced. When I remove both sticks of RAM, I get a continuous beeping, and according to the mobo handbook, means no RAM. So I think the mobo is functional, or atleast partly. I bought new RAM, but it still didn't work. I tried 3 monitors, with both VGA and DIV. So it's probably not the monitor, either. Now, let me get to the random part. Every 20 or so boots (I should also mention, for about 3 out of 5 boots I have to unplug the PC because it won't powerdown via the button), it will POST and I'll get display. Then, after about 2 or 3 resets, it won't work again. This confuses me so much, because even when I change nothing, it will/will not work. My thought is that maybe it has something to do with the RAM not clearing or something. I also reset the CMOS battery, incase that had anything to do with it, but no eval. I found some weird suggestion online about holding the power button for 30 seconds while it was unplugged. That did nothing, but I didn't expect it would... I've replaced just about the entire computer, and all the parts are compatible. Done about everything I can think of, but nothing has worked. Hopefully someone can help me here. And as I side note: When I do get my computer to boot, it says my hardware has changed and I have to re-activate windows. But it says I have to call Microsoft to do it. So I get this fancy automated voice that asks me to enter in a code into windows, then it asks me "How many computers have you activated with this copy of Windows?". Well, I had it on my computer before I replaced everything, so I said 1. Then he yelled at me for violating my 1-use license. I dunno what's going on there, do I have to re-purchase Windows 7? And they wonder why people pirate software... That's just a bonus question, though. Specs: 8GB of DDR2 RAM (Corsair) AMD CPU (I don't know what GHz or model because I can't find the box... (I think its 4 cores of 2.8Ghz) ASRock A785GM-LE Motherboard

  Read the article

• Frequent freezes with constant disk activity on SSD netbook

  - by SamsLembas

  I am running Arch Linux on an HP Mini 1000 with a SSD. The machine is a little under a year old and fairly heavily used. About a month ago the machine started freezing up. During the freezes, the system is almost completely unresponsive, seemingly especially for disk-intensive tasks such as launching an application for the first time since reboot. The disk activity led is always constantly illuminated during the freezes. After somewhere between 30 sec and 3 minutes, the machine returns to normal operation. I am pretty sure that the SSD is the source or the problem. Iotop reports a disk transfer rate of 0 during the freezes, so I think it must be getting "stuck" and simply not performing any r/w during the time. I can't seem to find any information on these symptoms on the Internet, so any input on exactly what might be the cause of this would be greatly appreciated. The machine is under warranty, but I would rather not deal with HP until I actually know what is going on. Thanks.

  Read the article

• I have been told to accept one error with Memtest86+

  - by DustByte

  Bought a new computer back in August with 4x4 GB RAM. Had problems with the RAM. They sent me four new sticks, which also generated errors. Singled out four sticks (from the eight I now had) that didn't generate any errors. Discovered by coincident a new RAM error last week (this time no BSOD). Contacted the company. According to them there have been issues with a bad stock from last summer so I got two tested 8 GB sticks sent to me. Been running Memtest86+ over the weekend. After 20 hours I got an error (see attached photo). The test has now been running for 37 hours but so far only this one error. I contacted the company where I bought the computer. They wrote back: I wouldn't worry about hat one fail. We have had similar situations here whereby it passes numerous times but then fails once. We think it's an issue with memtest, after all memory is faulty or it isn't so you can't really have it pass a few times, fail the next time around and then pass again! Please trust me on this and continue with the memory we sent you and if your problems continue we'll look at getting it replaced again. I gather from other forum posts that many people do not accept a single error. What could this single error signify, faulty RAM or a glitch in the MEMTEST program (or other)? Update: From the helpful comments below I conclude that an occasional (and rare) "random" error could occur and be acceptable, but repeated errors at the same address would indicate malfunction. Memtest has now run for 45 hours and I still have only one error. For everyone's information, I will keep running the test. In less than two days I am going away for a month. I will most likely leave Memtest running. As I do not have a UPS there is a risk that a power outage will ruin the experiment. The computer is a desktop so I cannot bring it with me (which would curiously have exposed it to more cosmic rays as I will be flying ;)).

  Read the article

• Dell Vostro Desktop error.

  - by goldenmean

  Faced a strange situation at work today. We have people sitting at a table on opposite sides, with power cables underneath the table. This morning when the person sitting opposite to me banged his feet on ground, it disturbed the power cable to my PC and it turned-off. So when I turned it on, it says, "No boot device found" Press F1 to setup or F5 to perform test... There was no physical impact/crash/fall of the desktop cabinet, which could have crashed/damaged the hard disk physically. EDIT: The OS is Windows 7 So I tried to recognize it in the Bios setup, but even there it could not find the SATA disk that is connected to this machine. So then I opened the cabinet, removed the power supply and plugged it back again. Tried to reboot, same error, "Boot device not found" It is not recognizing the hard disk. Any ideas about what might be wrong? Hard-disk crash, OS Crash(But it doesn't even go to the point of loading the disk after the initial Bios execution, so doubt this...) Any pointers about how I should proceed to troubleshoot/solve this error are welcome.

  Read the article

• Broken Motherboard Trace

  - by CoffeeBean

  When you're fairly certain that a motherboard trace is broken near the CPU (i.e.: you suspect heatsink / fan was improperly inserted) is it advisable to attempt a repair? I've heard that it can be done using a substance for repairing embedded windshield defoggers. Has anyone had any experience with this?

  Read the article

• Unable to create a Windows 7 system image of a failing hard drive

  - by Rahul

  The hard disk of my one year old T400 Thinkpad has started failing periodic hardware tests. I get a "Targeted Read Test Failed" error. The "SMART short self test" times out. I am now trying to create a Windows 7 System image of the hard disk but it fails without giving any specific error messages. I tried using Comodo Backup but got an error (code 101117) there as well. I have copied the important files in Dropbox but would like to take a full System backup as I have plenty of software installed on the machine. Does anyone know why this is happening and how I can take a backup of the system image ?

  Read the article

• Laptop goes black after a minute or so

  - by ZEDA-NL

  I have a laptop that is behaving strangely. When I turn it on, it does everything what it is supposed to do, but after a minute or so I hear a Click and all goes black. It's like it turns off the power. It doesn't matter what the laptop is doing. It also happens when it's just waiting in the Bios setup menu. Has someone experienced this before? Can it be the power supply? Can it be a cooling problem? Any ideas? By the way, it's a Compaq Presario Laptop, maybe 3 years old already.

  Read the article

• Why has my computer started to make noises when I turn it on after I put it into sleep mode for the first time a week ago?

  - by Acid2

  I would usually have my pc on all day and fully shut it down at night time before I went to bed. I decided to put it into sleep mode instead the other day and everything was fine but when I woke it from sleep, I was presented with the blue screen of death and it started with some weird noise that sounded like some spinning part was off balance or possibly hitting something periodically. Sounds like it could be a fan or maybe the HDD. I'm not sure why sleep mode would mess up the hardware. Anyway, now sometimes, randomly, when I turn my computer on from a previous shut down, I still get to hear the noise but the start-up is normal. Sometimes I don't hear anything for the entire duration while I have it on and sometimes it goes away after a few minutes and sometimes it doesn't and I have to restart, like it isn't going away right now. I can hear the noise as I type this. Anyone got possible solutions? I don't want to open the system and mess up other stuff. I'm also not sure if I should take it somewhere to have it fixed - it might not make the noise then and work like normal and nothing would seem like needing to be fixed. Add: I'm running Windows 7, if that's of any relevance.

  Read the article

• My MacBook Pro (2011) is dead

  - by Dave

  I connected my Sony digital camera with the MacBook and the screen turned black. I wonder why because the Sony camera was not on at the time and technically could not be accessed. So I thought it might be temporary and I turned on my camera. Well, it did not work, but my MacBook Pro has been dead since then. It will not turn on - when I hold the power button for five seconds, nothing happens. When I connect the charger cable, the green light is very dim and blinks a little (with about 20% illumination). I wonder what the problem is. I have to call Apple Care, but just so that I know, what could be wrong? Is my MacBook permanently dead? It might be under warranty but I am not sure.

  Read the article

• Toshiba Equium A110-252 laptop won't boot Windows.

  - by Drew Gibson

  I have a Toshiba Equium A110-252 laptop (XP Pro) which stopped booting a couple of weeks ago. The symptoms are that the laptop would display its DOS Toshiba splash screen, then the Windows (XP) boot screen would display, then a very brief blue screen flash, then back to the boot options screen (offering safe mode, safe mode with networking etc, last known good config, etc... none of these work). I assumed a duff HD, and swapped it for a new one and reinstalled from a TrueImage backup. This worked until I installed windows updates I think (the backup was a few months old), and now the PC is doing the same thing. I have installed a third, old HD (60GB) with Ubuntu 11.04 on it, and everything is fine. PC boots and runs Ubuntu beautifully. I need Windows running on it though ! Given these symptoms, could it a windows update issue ? Or might I have a hardware fault still ?

  Read the article

• How can I detect hard drive failures?

  - by Francis

  I am in charge of a large number of Windows servers. Recently, many have been reporting hard drive errors with event codes 11 and 55. CHKDSK indicates that the drives are fine most of the time. What other diagnostic tools could I use to more accurately detect hard drive failures? Could these Windows events be false positives? I have already evaluated S.M.A.R.T., and it seems to have significant sensitivity and specificity issues.

  Read the article

• Weird RAM Upgrade Experience

  - by Axel Isouard

  I have a laptop, HP EliteBook 8540p having originally 4GB RAM and I've recently bought Corsair Value Select SO-DIMM 16 Go (2x 8 Go) DDR3 1333 MHz. It fits the required RAM specifications perfectly, and once I've inserted them, the BIOS recognizes the memory correctly, but my linux Gentoo running on kernel 3.1.6 SMP x86_64 crashes immediately when I'm running an app which consumes a lot of memory. The laptop crashes as if there's no more battery left, when the memory reaches at least 6000MB ram. Windows 7 doesn't want to run anymore, it shows a blue screen with the IRQ LESS OR EQUAL error if I set 8GB, and it doesn't boot at all if I set 16GB. Is there something I could do to fix this please ?

  Read the article

• Starting old computer - nothing shown on screen at boot

  - by Jonas

  I'm trying to start an about 10 years old PC computer. But nothing is shown on the screen, and it beeps everytime I press a key on the keyboard. I can press Ctrl+Alt+Del to reboot the computer. The monitor is newer and seem to work with other computers. I don't see anything from POST/BIOS at start or later. I have tried to change to another graphic card, but it didn't change anything. What can I do to solve this problem? Update: I have now tried with another computer (the one where the "another graphic card" came from) and I got the same problem. I doesn't show anything on the screen. Both these computers had a GeForce2 MX 400 graphic card. I tried with another computer screen it didn't work - it was showing "signal out of range". So is the graphic card GeForce2 MX 400 too old for newer TFT-monitors? I tried with a third computer so I know that the monitors are working, and both monitors work fine with that computer.

  Read the article

• New MOBO + old Harddrive = NO BOOT

  - by rm

  My old mobo died, i bought a new one and swapped it. Plugged my old Harddrive and fired it up. I get a POST screen, the Windows logo ... and then the system restarts. Any ideas?

  Read the article

• New harddrives failing within weeks.

  - by Jason Kealey

  I've experienced 8 hard disk failures in 3 months and have tried many things to solve the issue permanently but I have failed. I would like to know if you have any advice for me. System was running Win XP on an Asus P5W-DH Deluxe. I have setup a RAID-1 array. I started out with 2 x 500 GB 7200RPM Western Digital drives. One died. I took it out to RMA it. On the same day, the router was fried. Assumed a power surge occurred; connected an older UPS to protect the system. Once I got my hands on an identical disk, I installed it. The RAID array was rebuilt. A few days later, the other one died. Assumed the rebuild caused it to fail. Took it out for RMA. Before the other one arrived, the remaining one died. I then discovered I could re-enable them using the Intel Matrix Storage Manager. I re-enabled both and the system seemed fine for a week, until both died again. I got two new 1.5 TB 7200RPM Seagate drives and re-installed Windows 7. Also replaced the UPS and power supply. They both died again. The voltage on the plug is stable between 120 and 122V as per the UPS. None of the other devices have had any problems (monitors, etc.). At this point, I see two options: a) electrical issue in the house that was, for some reason, not blocked by the UPS. b) something else inside the system causing surges? motherboard? onboard raid controller? Failures happen fairly quickly, between 2 and 14 days after I fix the previous issue. I just gotten a new computer (Core i7) to replace it. If it is stable, I can determine that b) was the problem. If it fries its hard drive again, I can determine that it is an electrical issue in the house. Do you have any other thoughts? Any tools I can run on the drives that failed to get more information about the original SMART event history?

  Read the article

• HDD not detected whenever first power on (detected at BIOS level)

  - by Alvin Lim

  I am using Asus P8H61-M LX Motherboard with latest version of BIOS: 4401 One SATA-3 Western Digital Black Series 1.5TB is attached to SATA port 0 A Samsung 22x DVDRW SATA drive attached to SATA Port 1. ps/2 Logitech mouse and keyboard. CPU is i3 with DDR3 8Gb RAM. no other devices are installed. My problem is that when I turn on the computer, the WD HDD is not detected. ie cannot be booted. I have to press ctrl+alt+del in order to get it detected. I'd used the WD data lifeguard software to scan the HDD, the smart status is OK, the surface scan does not show any error at all. Where did I do wrong? Any advice is greatly appreciated.

  Read the article

• Laptop powering off after 10 mins or so

  - by Jack

  I have no OS installed, and I am trying to use a linux boot disc. However it is not a linux problem....if I just leave the computer on at the no operating system found message, it still turns off. I thought maybe it was overheating, but I am 90% sure that is not the problem. What else could cause this? I should have mentioned, it's a laptop.

  Read the article

• water cooler fan in my computer room............

  - by metal gear solid

  Is using water cooler fan in my computer room HARMFUL for the internal parts of the computer system?

  Read the article

• HP Pavillion dv6 laptop - 15 beeps on startup and a black screen?

  - by dunc

  Usual story - girlfriend's step-brother's laptop is broken. I don't know a huge amount about what occurred before it broke, but I do know the following: When you try to turn the laptop on, it beeps 15 times exactly. The screen remains black. The LED on the Caps Lock key flashes continuously. If left on, the laptop never boots - as far as I can see. If left on, on a stable surface with decent ventilation for a relatively short period of time, the laptop (below keyboard, but not where the RAM/HDD are) gets very hot. I've tried doing what most websites appear to recommend for similar problems, which is to disconnect AC and battery then hold the power button down for a minute before reconnecting the AC and trying to turn the laptop on - no difference. EDIT I've also tried re-seating the RAM, to no avail. Any ideas? Thanks in advance,

  Read the article

• How long until the chirping stops or what can I do to make it stop?

  - by MadBurn

  I know computers, I have been fixing them and building them for over a decade... but I don't know the exact electronics of them. My personal desktop PC is making an irregular, but constant, extremely high pitched chirping noise. I know this could be my hard drive, but I've heard that noise before and I believe this is a capacitor or part of the electronics. This noise is right at the edge of my hearing and I can feel it more than I can hear it. After a while, it starts to give me a headache and makes me physically sick. How long will this last? Is there anything I can do to fix it (short of replacing the entire motherboard)?

  Read the article

• T60 Screen/LCD gets black after some minutes with a highpitched sound rising and fading

  - by edelwater

  Just now my T60 screen got "black" (so no display). On my second monitor: no problems so the VGA output works. Symptom: Screen blanks / no display, but it works on the second monitor Steps to reproduce: - boot - wait (it does not matter what you do you do not have to login or anything) - (now the monitor of the laptop slowly begins to make a ssssssssHHHHHHHHHHHHHHHHHWOEOEssssssss noise of about 10 seconds) - right after the sounds ends, the monitor gets black. Sometimes it seems to be the same each time. Software: Installed no new software before/after, running ZoneAlarm and antivirus. Other: It does not feel hot in any place, there don't seem to be running processes with strange behaviour. Warranty: Out of warranty What was I doing: Typing text on a website and doing some PHP coding in a text editor. What can I do here other than buy a new laptop? Does it sound familiar to known cases? Update 1: Exactly the same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-Screen-Blackout/m-p/288772 and the second poster (garyj), http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Black-Screen-on-T60/m-p/235053#M48627 And here: "I have that same problem. I replaced the CCRL on mine and it works fine when the screen is not screwed in. Once the frame of the LCD screen (metal portion) touches the metal on the laptop which holds the screen the screen goes black. If the metal is touching the screen when you boot up it boots up with it being very dimmly lit. " from http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-screen-problems/m-p/205047#M44995 (it seems replacing the LCD display is no use, he tried it three times). Same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-black-screen/m-p/80604#M25914 Hmmm... not handy 3 or 4 months ago I ordered and installed a new fan. Now the LCD. Which does not seem the core issue but some electric issue so it seems replacing the LCD is not the thing to do here. If it is not the LCD that needs to be replaced (see other threads), which parts can I order to fix this? Is there any information which could lead me to identify the issue? I have read replacing the "inverter" AND the "backlightning" would that make sense? Update 2: I replaced the inverter with another inverter, but IO have the same problem. I DID notice that the inverter is the component that makes the sssssssssssssHHHHHHHHHH sound AND it becomes very hot in a few seconds. (So both the old and the test one) The problem is hmmm wat is then the thing that makes the inverter hot by (assumption) after which it shuts itself down. Is it either the input or the output? The output seems to me not, because the screen seems to function so it must be the electricity coming in. But what causes it to become so hot would it be the VGA card outputting some unusual high voltage seems unlikely? I am looking for the component to order / replace update 3: Great news. Ewendish gave me the hint to look in the BIOS. While I was in the BIOS I noticed that the screen did not switch off and there was not a high pitched sound. So I lowered some settings in the BIOS. I then noticed that with brightness turned to 0 (via FN End), it does not make a high pitched sound and does not turn off, with brightness turned up just three "stripes" it starts making the sound. So I could from now on work under lowest brightness modus or... see where the problem lies. So as stated below with either power management or display drivers / ATI Catalyst settings / Windows display settings. I'm trying to see where it lies, but I will google some first. Update 4: I wiped clean the Windows XP installation and installed Windows 7 on it. Unfortunately the problem remains: as soon as the brightness goes up the screen starts hissing. This means... back to original thought: it probably IS a hardware problem. Although ... again... if it is NOT the inverter, what is it? Could it be the backlightning component? I could try to switch that with a another T60... but this is quite tricky.

  Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >