Search Results

Search found 15389 results on 616 pages for 'external js'.

Page 36/616 | < Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >

  • HDMI video output not working for external monitor

    - by user291852
    I have installed from scratch ubuntu GNOME 14.04 with gnome-flashback on my old HP HDX 16 laptop (core 2 duo p8600 + nvidia GT9600M + 4GB of ram) and I have problems with the HDMI output (I use it to extend my desktop on a dell U2412M 1920x1200 monitor). In the following I summarize the configurations that I have tried: Using the open source nouveau drivers, only the laptop monitor works, no signal from the external monitor connected to the HDMI output. However, the output of the xrandr command show that the HDMI output is connected with the correct resolution 1920x1200 (I find this thing really weird). Nouveau drivers with VGA connection works without problems on the external monitor, but the image is blurry compared to the HDMI connection. Using the nvidia drivers (I have tried different versions: nvidia-331-updates and the xorg-edgers versions nvidia-334 and nvidia-337) the HDMI output works, but I have system instabilities, random crashes and display freezes. I can't even enter in terminal mode with ctrl-alt-f1, so I have to manually shut down the laptop with the power button. I really would like to use the HDMI output with the nouveau drivers to avoid the system instabilities that I experienced with the nvidia drivers, but I can't figure out how to make it works. Alessandro

    Read the article

  • Can't access external hard drives or thumb drives

    - by calden
    I am not a complete linux noob but I don't know a lot either and would greatly appreciate some help with this. I just installed Ubuntu 10.10 onto my laptop. Everything is working great however USB devices such as thumb drives and external hard drives wont show up. I have been looking around a bit and when I run sudo fdisk -l it displays this: Disk /dev/sda: 250.1 GB, 250059350016 bytes 255 heads, 63 sectors/track, 30401 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00065684 Device Boot Start End Blocks Id System /dev/sda1 * 1 29255 234983424 83 Linux /dev/sda2 29255 30402 9212929 5 Extended /dev/sda5 29255 30402 9212928 82 Linux swap / Solaris Disk /dev/sdb: 16.0 GB, 16026435072 bytes 64 heads, 32 sectors/track, 15283 cylinders Units = cylinders of 2048 * 512 = 1048576 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x000df90d Device Boot Start End Blocks Id System /dev/sdb1 * 1 15283 15649776 7 HPFS/NTFS It does seem to display my 16 gig thumb drive but other then seeing it here I cant access it to read and write files to it. It does the same with my external hard drive. I know those devices work as I have tried them on my other computer and they are working fine. Also this is what is in fstab if this will help anybody help me: proc /proc proc nodev,noexec,nosuid 0 0 /dev/sdb1 / ext4 errors=remount-ro 0 1 /dev/sdb5 none swap sw 0 0 Thank you very much for the help everyone.

    Read the article

  • mount ext4 formated external drive->the drives green light won't stop flashing

    - by Gohlool
    I've installed kubuntu (after 10 years I am trying to play with linux) and manged to attach a external 1TB HDD drive over USB! The drive was formatted with NTFS and everything was working OK. I also changed the /etc/fstab here is my ntfs mount setting: /dev/sdb1 /media/samsung nts-3g auto,user,uid=1000,gid=1000,fmask=000,utf-8 0, 0 Now, I've reparationed the drive and formated it with ext4 filesystem! change my fstb like: /dev/sdb1 /media/samsung ext4 defaults,noatime 0, 0 now, when I plug my dive/or call sudo mount -a, my external drive's green light starts to flash and won't stop, but mount works .... What is the Problem? is this because of ext4? because with NTFS this won't happen! btw. after changing the owner of the /media/samsung and setting permissions 777, I can also access my drive like creating new folder atc. (although is's flashing constantly)! What is my mistake? btw. can you please let me know how to set the owner and the permissions for my /media/samsung directory in fstab for ext4 like I did it for NTFS? Thanks in advance

    Read the article

  • Removing spam external links after pharma hack?

    - by Beatchef
    Back in February my work's site was attacked by a pharma hack at the shared hosting end. I managed to find the placed file and the reference to run it in one of our files. I deleted this file, deleted and redownloaded all of the plugins and themes and reinstalled Wordpress. However I could never find the database entries no matter what I have read up on. Searching for known entries or for drug names backwards etc. On the Google and Bing end I have managed to deny and delete the entries and cache of most if not all of the bad links that the hack managed to instantly SEO to death (why don't these guys work legit and make more money?) However the one thing that is remaining is external links on the homepage that are invisible except when the site is viewed in google cache or scanned with unmaskparasites.com (and says that the external links are safe even though they're obviously not!). http://www.UnmaskParasites.com/security-report/?page=kmcharityteam.co.uk All sorts of website scans say there's nothing wrong with it and I can't find the source of the links in the header or footer or anywhere in the theme. I've searched for the links in the database but no use there either and they change every day so really I'd have to be looking for a generator? Does anybody have any advice or a solution for removing these links? Thanks!

    Read the article

  • Automatically revert to laptop screen when external monitor unplugged

    - by Ryan
    I regularly use an external monitor with my laptop, so when I use it, I usually have the laptop screen disabled when the monitor is connected, and this seems to cause problems when the monitor is disconnected. If the monitor is connected while the laptop screen is disabled, I can't get the X session to show up at all: I can Ctrl+Alt+F1 to open a terminal, and that works fine.. ..but Ctrl+Alt+F7 does nothing. The display is blank, and stays blank. The same thing happens whether I put the computer to sleep with the monitor connected, or if I disconnect while the computer is still awake. Rebooting the computer fixes the issue, as does killing Xorg and starting it again, but both of those are sub-optimal since I lose my current session. I'm currently using the open source graphics driver (xserver-xorg-video-ati). This question looks like it might answer my question, but unfortunately hwinfo is no longer available in the apt repository. Is there a way with current tools to automatically detect when the external monitor is disconnected and switch to the laptop display?

    Read the article

  • Upgrading to 12.10 on an external hard drive

    - by Tom Childers
    I did some googling on this and didn't find anything specific for my situation. I currently have 12.04 installed on an external USB hard drive. It's working great. I want to upgrade it to 12.10. My bandwidth is very limited so I have a friend who will download 12.10 for me and put it on a flash stik. Then I can upgrade without having to do the download myself. Which particular version of the 12.10 download file(s) should I get? Are there alternate 12.10 downloads that have all the packages? How do I set it up so when I upgrade 12.04 I can specify that it look in some local repository for the 12.10 files? Can I just dump the 12.10 files in some local directory? Or do I have do go thru some complex commands to create a local repository? I'm pretty new to Linux so a long process of complex terminal commands will probably be a show stopper for me. Remember that my 12.04 install resides on an external hard drive. And I have a laptop with multiple USB ports. Thanks! Advait

    Read the article

  • Js (+Mootools) - Why my script use over 60% of processor?

    - by Misiur
    On this site - LINK - i need to use 3 banner scrollers (2x vertical + 1x horizontal). I've tried to do it in flash, but then everyone web browsers shut down, or suspended. Now i want to do it in JS (i use mootools). All data come from MySQL. Here's the complete code (even if you don't know mootools, You should understand it) global $wpdb; $table = $wpdb->prefix.'part'; $sql = "SELECT * FROM $table"; $q = $wpdb->get_results($sql); $g = 0; if($wpdb->num_rows > 0) { ?> <script type="text/javascript"> window.addEvent('load', function(){ var totall = 0; var totalr = 0; $$('#leftCont0 .contElement').each(function(el){ var img = new Asset.image(el.getFirst('a').getFirst('img').get('src')); totall += img.height; }); $$('#rightCont0 .contElement').each(function(el){ var img = new Asset.image(el.getFirst('a').getFirst('img').get('src')); totalr += img.height; }); $$('.leftCont').each(function(el){ var h = parseInt(el.get('id').substr(8)); el.setStyle('top', h * totall); }); $$('.rightCont').each(function(el){ var h = parseInt(el.get('id').substr(9)); el.setStyle('top', h * totalr); }); var total = new Array(totall, totalr); move.periodical(30, null, total); }); function move(num, num2) { var h = 0; var da = false; var target = null; $$('.leftCont').each(function(el){ var act = el.getStyle('top'); var n = parseInt(act)+1; el.setStyle('top', n+"px"); if(el.getStyle('top') < h) { h = parseInt(el.getStyle('top')); alert(h); } if(parseInt(el.getStyle('top')) > 400) { da = true; target = el; } }); if(da) { var n = h - num; target.setStyle('top', n+'px'); } h = 0; da = false; $$('.rightCont').each(function(el){ var act = el.getStyle('top'); var n = parseInt(act)+1; el.setStyle('top', n+"px"); if(el.getStyle('top') < h) { h = parseInt(el.getStyle('top')); alert(h); } if(parseInt(el.getStyle('top')) > 400) { da = true; target = el; } }); if(da) { var n = h - num2; target.setStyle('top', n+'px'); } } </script> <?php $g = 0; $l = 0; $r = 0; $leftContent = array(); $rightContent = array(); $leftHeight = 0; $rightHeight = 0; foreach($q as $q) { if(($g % 2) == 0) { $leftContent[$l] = '<div class="contElement"> <a href="'.$q->aurl.'"><img src="'.$q->imgurl.'" alt="Partner" /></a> </div>'; $lHeight = getimagesize($q->imgurl); $leftHeight .= $lHeight[1]; $l++; } else { $rightContent[$r] = '<div class="contElement"> <a href="'.$q->aurl.'"><img src="'.$q->imgurl.'" alt="Partner" /></a> </div>'; $rHeight = getimagesize($q->imgurl); $rightHeight .= $rHeight[1]; $r++; } $g++; } $quantity = ceil(400 / $leftHeight) + 1; for($i = 0; $i < $quantity; $i++) { $str = ""; for($j = 0; $j < sizeof($leftContent); $j++) { $str .= $leftContent[$j]; } $leftContainer[$i] = '<div class="leftCont" id="leftCont'.$i.'">'.$str.'</div>'; } $quantity = ceil(400 / $rightHeight) + 1; for($i = 0; $i < $quantity; $i++) { $str = ""; for($j = 0; $j < sizeof($rightContent); $j++) { $str .= $rightContent[$j]; } $rightContainer[$i] = '<div class="rightCont" id="rightCont'.$i.'">'.$str.'</div>'; } ?> <div id="pcl"> <?php for($i = 0; $i < sizeof($leftContainer); $i++) { echo $leftContainer[$i]; } ?> </div> <div id="pcr"> <?php for($i = 0; $i < sizeof($rightContainer); $i++) { echo $rightContainer[$i]; } ?> </div> <?php }

    Read the article

  • Chrome extension Page Action JS

    - by Radek Šimko
    I'm trying to create an extension using this docs: http://code.google.com/chrome/extensions/content_scripts.html I want a part of JS code to run when document is ready (loaded). This is my manifest.json: { "name": "OwnExtension", "version": "0.1", "content_scripts": [ { "matches": ["https://my.site.eu/*"], "css": ["styles.css"], "js": ["main.js"] } ] } This is my main.js: alert(10); Am I doing sth wrong, that nothing happend when page https://my.site.eu/ loaded in browser?

    Read the article

  • embed js code issue from rails application

    - by Arpit Vaishnav
    I am on the ruby on rails application and trying to embed the code for js , added the whole code for embedding in Text box , But when i copy paste in other blogs where embed is poss , i am not getting the full js work , the code is given below <%= text_field_tag "text"," script src=\"/public/javascripts/calendarview.js\" script src=\"/public/javascripts/calendarview_init.js\" link rel=\"stylesheet\" href=\"/public/stylesheets/calendarview.css\" link rel=\"stylesheet\" href=\"/public/stylesheets/calendarview_init.css\" ",:size = 40 % I have just removed < for let it be seen in the coding window PLease help if poss List item

    Read the article

  • After Port Forwarding, how to get my external IP in Java ?

    - by Frank
    I set up a static IP and did port forwarding on my notebook, and now I have a static IP address, but it's relatively static, every time I re-start the machine, I get another address, and since I have a "static" IP I can now do Paypal IPN messaging. But how can I get this static IP from my Java program ? One way I can think of is to visit : http://portforward.com/ and on that page it tells me what my external IP is, so I can extract it with Java code, is there any other way that I can do in my Java code to get this info ?

    Read the article

  • SQL SEVER – Finding Memory Pressure – External and Internal

    - by pinaldave
    Following query will provide details of external and internal memory pressure. It will return the data how much portion in the existing memory is assigned to what kind of memory type. SELECT TYPE, SUM(single_pages_kb) InternalPressure, SUM(multi_pages_kb) ExtermalPressure FROM sys.dm_os_memory_clerks GROUP BY TYPE ORDER BY SUM(single_pages_kb) DESC, SUM(multi_pages_kb) DESC GO What is your method to find memory pressure? Reference: Pinal Dave (http://blog.sqlauthority.com) Filed under: Pinal Dave, SQL, SQL Authority, SQL Optimization, SQL Performance, SQL Query, SQL Scripts, SQL Server, SQL Tips and Tricks, T SQL, Technology

    Read the article

  • Great Free Courses on Building HTML5 apps using ASP.NET Web API, Knockout.js and jQuery

    - by ScottGu
    Pluralsight has developed some great training courses on the new .NET 4.5 and VS 2012 release, including two fantastic courses from John Papa that cover how to build HTML5 web apps using ASP.NET Web API, Knockout and jQuery: Single Page Apps with HTML5, Web API, Knockout and jQuery Building HTML5 and JavaScript Apps with MVVM and Knockout Free 1-Month Subscription to the Courses Pluralsight is offering a special promotion that allows you to get a free 1-month subscription to watch the above courses at no cost.  There is no obligation to buy anything at the end of the offer and you don’t need to supply a credit card in order to take part in it. To get access to the course you simply follow @pluralsight and @john_papa on Twitter and then visit this page and enter your Twitter name using the form on it.  Pluralsight will then send you a private twitter message containing the access code that you can use to subscribe to the courses (and download the course exercise files).  Once you are subscribed to the course you have one month to watch the course (and you can watch it as many times as you want during the month). Pluralsight is running the promotion through Sept 18th – so sign-up now to get access.  Once you are signed up you then have a month to watch the course. Hope this helps, Scott P.S. And if you are new to Twitter you can also optionally follow me: @scottgu

    Read the article

  • HFS+ hard drive being mounted as read only

    - by DNA
    This is a recurring problem and occurs a few times a week. I have an external hard drive which is hfs+. Every couple of weeks, for no obviuous reason, when I mount it by pluggin it in to my Ubuntu 11.10, it is read only and I can't copy any files into it. I gksudo nautlius and change the ownership and it magically works in some time. But returns to the read only state soon in a few hours-days without any rhyme or reason. Right now my fstab doesn't have any entry for my hard drive. What gives? What in the world is going on with Linux/HFS+? This is frustrating. I can't reformat my hard drive because I have almost a terrabyte of data in it and no receptacle to hold it while I reformat it.

    Read the article

  • libssh2 and simultaneous connections

    - by Florian Margaine
    I'm writing a node.js C++ module using the C library libssh2. The module is supposed to be a bridge to connect to SSH over HTTPS. Right now, I'm still in the design/learning phase of v8 API and C++, and I have a design question: libssh2 is a C library, all its methods are global. From what I see in the examples, libssh2 can only handle one connection at a time. If I want to allow simultaneous connections to different SSH servers, do I have to fork a process to completely separate the libssh2 "instances", or is forking a thread enough? I don't know enough of the separation limit used there. Any idea on how to handle this is appreciated.

    Read the article

  • Changing dual-monitor settings without closing the laptop lid on OS X

    - by hekevintran
    I have a Unibody MacBook hooked up to an external display. By default when I boot up, the system will go to dual-monitor mode. I want to use only the external display. The Apple supplied solution to this problem is to close the lid of the laptop which puts the machine into sleep mode and then move the mouse around to wake it up again. Because the machine is being woken up with the lid closed, when the displays are detected the system finds only the external. After the system is functional again, you can open the lid if you want and the laptop screen will be non-functional until you either tell the system to detect displays from the system preferences or you turn off the external display. Every time I want to use only the external display, I must reach my hand over to close the lid, wait for the machine to sleep, jigger the mouse, wait for the machine to wake up, and finally open the lid again because I don't want the machine to overheat. I feel that this is very stupid to have to do. Why is there no button or menu option that says "don't use this screen"? Is there any third-party software way to change the screen setup that does not involve physically closing the lid and playing a game of "are you sleeping" in order to switch such a simple software setting? We are in the 21st Century and honestly this is childish.

    Read the article

  • How to install NPM behind authentication proxy on Windows?

    - by Tobias
    I need to run the latest version of Node and NPM on Windows. I installed Node 0.5.8 and downloaded the sources of NPM from GitHub. The steps I followed to install NPM were listed on its GitHub site but I have a problem running the following command: node cli.js install npm -gf but it fails with the following error message: Error: connect UNKNOWN at errnoException (net_uv.js:566:11) at Object.afterConnect [as oncomplete] (net_uv.js:557:18) System Windows_NT 5.1.2600 command "...\\Node\\bin\\node.exe" "...\\npm\\cli.js" "install" "npm" "-gf" cwd ...\npm node -v v0.5.8 npm -v 1.0.94 code UNKNOWN I think that this is a problem because I need authentication at my proxy to connect to the Internet. But I found no way to tell the installer to use my credentials for login. Is there a possibility to provide my proxy IP and login information to npm installation maybe via command-line arguments? I can provide the full log (but seems to have no more relevant information) using pastebin if needed.

    Read the article

  • What are the best practices for rapid prototyping using exclusively HTML/CSS/JS

    - by charlax
    I'm developing a prototype of a web application. I want to only use HTML, CSS and Javascript. I prefer to use my text editor and not having to learn (or pay, for that matter) a new tool like Axure. What would be, to your mind, the best practices? To me there are many qualities for a good prototype: Quickly developed Easy to improve Fair fidelity as regards UX (this disqualifies tools like Omnigraffle or PowerPoint that are more dedicated to wireframing) I trying to learn as quickly as possible, but I would like to know, based on your experience, on how you managed to be both quick and agile. Reference: http://www.boxesandarrows.com/view/prototyping-with

    Read the article

  • How do I mount this HDD?

    - by Casval Deikun
    I have a Windows HDD attached to an external docking bay on my Ubuntu System, but the HDD brings up an error message: Mounting exited with exit code 14:windows is hibernated, refused to mount. Failed to mount '/dev/sde2':Operation not permitted. The NTFS partition is hibernated. Please resume and shutdown windows properly or mount the volume read-only with the 'ro' mount option, or mount the volume read-write with the 'remove_hiberfile' mount option. For example type in command line: mount -t ntfs-3g-o remove_hiberfile/dev/sde2/media/FE46D60C46D5C615 I am at a loss for exactly how to remove the hiberfile, or even mount it as read-only or read-write. I tried directly copy and pasting that exact command into my terminal, but it said: mount:only root can do that I do not know what to do at this point. I do need to get the information off of this drive, but I do not have a computer to put it in. Does anyone know what I should do from here?

    Read the article

  • does my js replace view?

    - by Milla Well
    I am writing a web application which is based on Codeigniter and jQuery. I primarily use ajax to call my controller functions and it turned out, that there are just 4 view*.php files, because most of my contoller functions return JSON data, which is processed in my jQuery. So my actual code is divided in kind of MVCC model: Codeigniter model (db, computations) Codeigniter controller (filtering, xss-cleaning, checking permissions, call model functions) jQuery controller (callback functions) jQuery view (adding/removing classes, appending elements,... ) So I violate the paradigm of not using the echo function in my Codeiginter controller and simply call echo json_encode($result); because it doesn't make any sense to me to create a view*.php file for one loc. Especially because all the regular view*.php stuff is covered in my jQuery view. I was wondering if I am missing something out, or if there is a way to integrate this jQuery-controller in my Codeigniter. I found some words on this topic, but this seems pretty handmade. Are there some neat solutions? Does a MVCC model make sense?

    Read the article

  • Remote Desktop Services Gateway Issue

    - by AVandelay05
    Alright fellow techies here's the rundown. I have installed Server 2008 r2 Remote Dekstop Services on a VM in my network. I installed the following RD role services: RD Session Host, Licensing, Connection Broker, Gateway, Web Access. When I set things up originally, the gateway server and RDWeb worked as it should locally. After getting things running locally (remoteserver.domainname.local) I wanted to test things externally. From the outside, I couldn't get things running (meaning I could connect to rdweb access externally, but when I tried to run an app I would get the message "can't connect/find computer"). Here's my setup for external access The VM has every RD Services role services installed on it, meaning it acts as gateway, rd web access, session host, licensing, the whole bit. I made a self-signed certificate on the gateway server (gateway.domainname.net is the cert name). Internally, I have a secondary forward-lookup zone called domainname.net with an A record gateway pointing to the local IP of the gateway server. On our public DNS (domainname.net) I have an A record gateway. This is to access the RDWeb externally. In IIS I have the following authentication settings RDWeb: All disabled except for anonymous authentication Rpc: All disabled except for basic and windows RpcWithCert: All disbled except for windows authentication I have the necessary web access config in our sonicwall tz210 (https and rdp, external ip pointing to local ip of rds server) RAP and CAP have the correct user and computer groups, authentication, and allowed devices After all of this, here's what happens accessing externally. I can login correctly to RDWeb Access (I've tried a bogus login, I can't login to it so that's working properly). I see the Apps for use. I click on an app, click connect, the credential window opens, I put in the correct user creds, it tries to connect to the gateway server, but then the cred window comes back in view. I tried to reach a limit of failed logins, but never reached one, haha. So from the same external client machine I try to connect to the gateway through a Remote Desktop connection. I put in the correct gateway settings in the RD window, try to connect and get the same results as I did in RDWeb access. I checked the event logs on the RD Services machine and saw the following event IDs around the time I tried to login externally: ID 6037 with the message "The program svchost.exe, with the assigned process ID 2168, could not authenticate locally by using the target name host/gateway.domainname.net. The target name used is not valid. A target name should refer to one of the local computer names, for example, the DNS host name. Try a different target name." ID 10 RADWebAccess "RD Web Access was unable to access gateway.domainname.net, which is the server that is specified as running the RemoteApp and Desktop Connection Management service. Ensure that the computer account of the RD Web Access server is a member of the TS Web Access Computers security group on gateway.domainname.net" ID 4625 "An account failed to log on. Subject: Security ID: NULL SID Account Name: - Account Domain: - Logon ID: 0x0 Logon Type: 3 Account For Which Logon Failed: Security ID: NULL SID Account Name: Administrator Account Domain: gateway.domainname.net Failure Information: Failure Reason: Unknown user name or bad password. Status: 0xc000006d Sub Status: 0xc000006a Process Information: Caller Process ID: 0x0 Caller Process Name: - Network Information: Workstation Name: USER-LAPTOP Source Network Address: External IP Source Port: 63125 Detailed Authentication Information: Logon Process: NtLmSsp Authentication Package: NTLM Transited Services: - Package Name (NTLM only): - Key Length: 0 This event is generated when a logon request fails. It is generated on the computer where access was attempted. The Subject fields indicate the account on the local system which requested the logon. This is most commonly a service such as the Server service, or a local process such as Winlogon.exe or Services.exe. The Logon Type field indicates the kind of logon that was requested. The most common types are 2 (interactive) and 3 (network). The Process Information fields indicate which account and process on the system requested the logon. The Network Information fields indicate where a remote logon request originated. Workstation name is not always available and may be left blank in some cases. The authentication information fields provide detailed information about this specific logon request. - Transited services indicate which intermediate services have participated in this logon request. - Package name indicates which sub-protocol was used among the NTLM protocols." I don't think the VM has a null SID. The SID of the VM and it's physical host have different SIDS. I can access the blank page for rpc externally using the external gateway name. It seems like authentication is a problem. Also, is it a problem that the external name of the gateway server doesn't match the local name? The external name (which the cert is based on) is gateway.domainname.net and the internal name is remoteserver.domainname.local. That's the only thing I can think of that would be the problem, but the external name has to be different from the local right? Internally, I ping gateway.domainname.net and it gives me the correct local IP of the server. Now, there isn't an actual computer name in AD, but I don't know how I would achieve that? I hope I've been clear....any help would be appreciated. I think I'm close to achieving this. :)

    Read the article

  • HAProxy is caching the forwarding?

    - by shadow_of__soul
    i'm trying to set up a server structure for an application i'm building in Node.js with socket.io. My setup is: HAProxy frontend forward to -> apache2 as default backend (or nginx, is apache in this local test) -> node.js app if the url has socket.io in the request AND a domain name i have something like: global log 127.0.0.1 local0 log 127.0.0.1 local1 notice maxconn 4096 user haproxy group haproxy daemon defaults log global mode http maxconn 2000 contimeout 5000 clitimeout 50000 srvtimeout 50000 frontend all 0.0.0.0:80 timeout client 5000 default_backend www_backend acl is_soio url_dom(host) -i socket.io #if the request contains socket.io acl is_chat hdr_dom(host) -i chaturl #if the request comes from chaturl.com use_backend chat_backend if is_chat is_soio backend www_backend balance roundrobin option forwardfor # This sets X-Forwarded-For timeout server 5000 timeout connect 4000 server server1 localhost:6060 weight 1 maxconn 1024 check #forwards to apache2 backend chat_backend balance roundrobin option forwardfor # This sets X-Forwarded-For timeout queue 50000 timeout server 50000 timeout connect 50000 server server1 localhost:5558 weight 1 maxconn 1024 check #forward to node.js app The problem comes when i made a request to something like www.chaturl.com/index.html it load perfectly but fails to loads the socket.io files (www.chaturl.com/socket.io/socket.io.js) why it redirect to apache (and should redirect to the node.js app that serve the files). The weird thing is that if i access directly to the socket.io file, after refreshing a few times, it loads, so i suppose is "caching" the forwarding for the client when it makes the first request and reach the apache server. Any suggestion of how this can be solved? or what i can try or look about this?

    Read the article

  • USB file transfer preparing to copy, but file count climbs indefinitely

    - by Alex
    I have downloaded Ubuntu 12.04 to back up my Windows machine that won't boot and am running Ubuntu from the CD. I copied and pasted a volume of about 160GB to my external HDD. The transfer has been stuck in the "preparing to copy" stage for several hours and is displaying a file/GB count about twice as high as the volume of data actually being copied! The number is now larger than the entire partition that's being copied from! However I know it's doing something because occasionally it pops up with a minor I/O error on this or that file which I then have to click through. I've not had this problem before so I can only assume it's a Linux/Ubuntu thing. More importantly what I want to know is is there any other way to copy it across that will actually work?

    Read the article

  • Possibility of recovering files from a dd zero-filled hard disk

    - by unknownthreat
    I have "zero filled" (complete wiped) an external hard disk using dd, and from what I have heard: people said you should at least "zero fill" 3 times to be sure that the data are really wiped and no one can recover anything. So I decided to scan the disk once again after I've zero filled the disk. I was expecting the disk to still have some random binary left. It turned out that it has only a few sequential bytes in the very beginning. This is probably the file structure type and other headers stuff. Other than that, it's all zeros and nothing else. So if we have to recover any file from a zero filled disk, ...how? From what I've heard, even you zero fill the disk, you should still have some data left. ...or could dd really completely annihilate all data?

    Read the article

< Previous Page | 32 33 34 35 36 37 38 39 40 41 42 43  | Next Page >