Search Results

Search found 11634 results on 466 pages for 'nested properties'.

Page 361/466 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

• Can't Configure IBM 8275-416 Switch Via Serial

  - by Sean M

  I am attempting to configure an IBM 8275-416 switch (I found a manual here) via serial connection. However, when I connect with HyperTerminal, the output contains a lot of garbage characters. It's pretty much unusable, because there's enough layout-breaking text-gunk that it's very difficult to determine what's actually being displayed. . I was able to reset the switch to factory defaults via the terminal interface, so I know that it's not entirely broken. It also performs basic functions all right (i.e., you plug in clients and Ethernet cables - they can connect to clients plugged into other ports) - but I'd like it to do more than that (VLANs yay). I don't know if its in-band UI is operational or not, because I can't get the terminal interface to behave well enough to properly turn on the web/SNMP UI. So that's not available. Things I've tried: - Changing the encoding: HyperTerminal lets me choose between Standard JIS and Shift-JIS. Neither setting fixes the issue. - Checking emulation settings: The manual demands VT100, 19200 baud, 8 data bits, and such: I have faithfully applied these settings, both in HyperTerminal's settings and in the properties of the COM1 port in Device Manager (connecting from a Windows machine). - Restoring to factory defaults: See above. Things that it could be, but that seem unlikely: - Cabling: Couldn't find a proper null-modem cable, so used two 232-to-RJ45 adapters. But if it was a problem with the cable, wouldn't it be more likely to not connect or do input at all, rather than just garble the text? Since I was actually able to perform the reset-to-factory defaults operation, I don't think it's this. - Device as a whole broken: It is a decade and change old, so it's possible that it's just dying slowly. Again, though, it seems like there would be more symptoms than just garbled text in the terminal. What else can I try to get a sane interface to this switch?

  Read the article

• Everyone can access my Windows 7 Homegroup file shares - Even Windows XP computers.

  - by adriangrigore

  Hi, I have 3 computers in my network, two running Windows 7 and one running Windows XP. I've set up a homegroup on both Windows 7 computers. Also, all computers are in the same Workgroup. The problem is that one of the Windows 7 computers makes all shares accessible to the entire Workgroup instead of just sharing to the Homegroup as it should be. I created the file share in Windows 7 via right-click in the explorer, then click on "Share For" - "Homegroup (Read/Write)" (translated from German, so the actual wording may be different). Also, when I look at the file sharing properties of that folder, Windows Explorer informs me that Users must have a valid account and password for this Computer to access drive shares. Unfortunately this is not true. Being in the same Workgroup is enough to get access. Homegroup restrictions work as expected on my other Windows 7 computer. When trying to browse those shares from the XP computer, I get a dialog asking for a login and password. What might cause homegroup restrictions to fail and how can I fix this?

  Read the article

• IIS virtual location path

  - by Worp

  Sorry in advance, for this seems to be a very noobish question and should be easily fixable, yet I can't work it out: I am setting up windows authentication for a website running on IIS 8.5: The Yii framework of the website takes input like http://localhost/mywebsite/index.php/site/loginand processes it, using the "login" action of the "site" Controller. I flipped on URL Rewrite to have nicer URLs, leaving the URL with /mywebsite/site/login. Now I need to set up windows authentication for this location. Very specifically ONLY for this very exact location. Only the /site/login location of mywebsite needs to have authentication. Every other location needs to have anonymous. Since it is a "virtual location", I don't know how to do it. I can set up win-auth for files, directories, virtual directories, etc. but not for virtual locations that do not map to any file but only to a Controller/Action in Yii. The working counterpart in Apache is but i can't "translate this into IIS". I have read that IIS does have the "~" symbol but I just couldn't make it work yet. Could it be used to achieve authentication on a location basis? I have looked around virtual directories as well, which seem to simply be a kind of "symlink" to actual folders on the harddrive. Can they be used differently to "create a virtual folder in a location that doesn't really exist to manage its properties"? Help is much appreciated.

  Read the article

• Known USB 2.0 devices don't install driver, but must be manually forced

  - by Darragh

  When a known USB 2.0 device is plugged in and detected, it doesn't install the driver correctly but shows a Code 28 error and lists the device under "Other Devices" in Device Manager. When view properties of this device , it shows the following status; The drivers for this device are not installed. (Code 28) There is no driver selected for the device information set or element. To find a driver for this device, click Update Driver. When updating the driver manually and selecting the appropriate driver Windows doesn't believes it's the correct driver, but you can force the installation and it works! The other condition the driver will auto-install is when the same USB device is plugged into a USB 3.0 port. Power related issues are not also causing this as I have tried vi a Docking station, USB hub. etc.. Devices tried; Jabra Headset USB-Mass Storage Device (flash disk and ext HD) MS Wireless Keyboard & Mouse USB Ethernet controller (USB-MAC controller) This is on a laptop part of a Domain with Windows 7 Ent 7601, I am logged in as a local administrator. There isn't any Group Policies blocking not signed driver or whitelisted devices on the domain. Any suggestions please feel free

  Read the article

• Group Policy for DNS Server Addresses

  - by John

  This question deals strictly with the methodology of using Active Directory to publish DNS settings and controlling the DNS server address order to domain attached clients. This is not asking about if this is the right function, role, or best use of group policy; but rather, how to make it work. I would like to be able to publish in group policy DNS addresses and possibly control the order in which the client consumes the addresses. I have tried following the information from this site without success. I set the following setting within group policy, but the client never shows the settings within the TCP/IP properties. Computer Configuration/Administrative Templates/Network/DNS Client/DNS Servers I did list them as a single space separated list. For example, the following: 192.168.0.1 192.168.10.3 192.168.34.2 192.168.2.67 192.168.56.99 192.168.99.23 This would be for Windows 7, Windows Server 2003, and Windows Server 2008 clients. I am not sure what I am doing wrong or how to get this to work. Am I missing a setting? Do I need to set something differently?

  Read the article

• ffmpeg: video file played OK on Ubuntu, but no sound on XP

  - by Andy Le

  I created a video clip using ffmpeg (vcodec: mpeg2video, acodec: AC3 5.1). The file can be played normally on Ubuntu, but when I play it on an XP machine, there is no sound. I can play AC3 files and other movies with AC3 sound. I already tried many codec packs and many players. When I compare the MediaInfo tab of the Properties window of the file with another playable movie, I see that the Audio Identifier of the audio stream in my file is 0x80 while it is 0x02 in the other movie. So I guess that's why players on XP can't recognize the audio codec. When I use an MKV container instead of MPEG (still mpeg2video codec), then the result is OK on both Ubuntu and XP (with the correct Audio ID). I really need MPEG though. Any idea? This is the command I used: ~/ffmpeg/ffmpeg/ffmpeg -loop_input \ -t 97 -r 30000/1001 -i v%4d.tga -i final.ac3 \ -vcodec mpeg2video -qscale 1 -s 400x400 -r 30000/1001 \ -acodec copy -y out6.mpeg 2 This is the output of mediainfo (on Ubuntu): General Complete name : out6.mpeg Format : MPEG-PS File size : 6.86 MiB Duration : 1mn 37s Overall bit rate : 593 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@Main Format settings, BVOP : No Format settings, Matrix : Default Format_Settings_GOP : M=1, N=12 Duration : 1mn 37s Bit rate mode : Variable Bit rate : 122 Kbps Width : 400 pixels Height : 400 pixels Display aspect ratio : 1.000 Frame rate : 29.970 fps Resolution : 8 bits Colorimetry : 4:2:0 Scan type : Progressive Bits/(Pixel*Frame) : 0.025 Stream size : 1.41 MiB (21%) Audio ID : 128 (0x80) Format : AC-3 Format/Info : Audio Coding 3 Duration : 1mn 36s Bit rate mode : Constant Bit rate : 448 Kbps Channel(s) : 6 channels Channel positions : Front: L C R, Side: L R, LFE Sampling rate : 44.1 KHz Stream size : 5.18 MiB (75%)

  Read the article

• Wake-on-lan only works so many times

  - by Chance

  I have Wake-on-lan configured on my Windows XP machine so that the computer will wake up from Standby. Waking the computer from Standby via network traffic seems to work a certain number of times, say 4 or 5, then it stops working. If I restart the computer it seems to reset this behavior so that I can use WOL a few more times before it starts working. I use the command "wol" on my other, Linux machine with the appropriate IP address and MAC address of the card. I looked at the network card to see if it had different lights when WOL worked and when it didn't. When it has a solid amber light where the ethernet cable connects, WOL seems to work. When it has a flashing amber light, WOL does not. It seems that the system seems to almost "shut off" the card when it falls to sleep, but I don't know if this is a function of time or number of standby/wakeups. I have a 3Com 3c920 network card. If I look at the properties in Device Manager, I have "Allow this Device to bring the Computer out of Standby" checked. In the Advanced tab I have anything related to RWU (Remote Wake Up) enabled. I also believe I have the appropriate settings in BIOS related to Remote Wake-Up and I have tried both S1 and S3 power configurations in the BIOS. Intuitively, I would think I would uncheck "Allow the Computer to turn off this device to save power", but doing so disables the "Allow this Device to bring the Computer out of Standby" option. Does anyone know what is happening here or if there is a way to fix it? I have an integrated network card; would getting one that goes into a slot be better? I am running Windows XP on a Dell Optiplex GX240 with a 3Com 3c920 network card.

  Read the article

• Windows 7 sharing folder from command line, selecting users and triggering the "Apply" of changes

  - by clintp

  I have a drive that doesn't get mounted until after I log in. (A Truecrypt thumbdrive device, and no, I'm not making it a "System Favorite" to get around this.) I'd like to construct a batch file to share it once I've gotten it mounted because the sharing info doesn't seem to stick through a reboot. From the GUI, I'd go into the folder Properties-Sharing. And then in Advanced Sharing I'd pick the name to share it as. And then under the "Share..." button I'd pick the users and the permissions I want to grant them. After "Apply" there's a pause -- I'm not sure what's happening here, but the dialog says "Sharing Items..." -- and then everything is okay. From the command line, I've done: net share MyFolder=F:\MyFolder cacls F:\MyFolder /G FirstUser:F cacls F:\MyFolder /G OtherUser:F And this almost works. I can see the share on the network then, but nobody has permissions to do anything. If I go into the GUI and change anything (and I can see my command-line changes in there already) and press "Apply" I get the: "Sharing Items.... This may take a few minutes" Dialog... and then Voila! It works. I get the "Your folder is shared" dialog with the command-line changes I made, along with the GUI change that I made to trigger the "Sharing Items..." dialog. Everything's peachy. Is a service being restarted? Which one? What's triggering the sharing to take effect? And -- more importantly -- how do I do it from the command line?

  Read the article

• TEMP environment variable occasionally set incorrectly

  - by Roger Lipscombe

  Occasionally, I find my TEMP and TMP environment variables set to C:\Windows\TEMP. They should be set to %USERPROFILE%\AppData\Local\Temp, and are configured correctly in System Properties. This manifests itself as error messages like the following: ---> System.InvalidOperationException: Unable to generate a temporary class (result=1). error CS2001: Source file 'C:\Windows\TEMP\gb_pz65v.0.cs' could not be found error CS2008: No inputs specified ...which occurs in various .NET applications (in particular Visual Studio 2010 or SQL Server Management Studio). Alternatively, SQL Server Management Studio will report: Value cannot be null. Parameter name: viewInfo (Microsoft.SqlServer.Management.SqlStudio.Explorer) If I run PowerShell elevated, then $env:TEMP is set correctly. If I run PowerShell non-elevated, then it's not. I believe that it should be set correctly in both cases. If not, it's the wrong way round. The same is true for CMD.EXE. Rebooting fixes it, temporarily, until something breaks it again. Presumably something loaded into Explorer.exe is messing with its environment variables, but what? The values in the registry are correct, even while this is happening: HKLM\SYSTEM\CurrentControlSet\Control\Session Manager\Environment has TEMP = %SYSTEMROOT%\Temp HKCU\Environment has TEMP = %USERPROFILE%\AppData\Local\Temp By setting a breakpoint on shell32!RegenerateUserEnvironment, I'm able to trap it when it happens, but I still don't know why explorer.exe is reading the wrong environment variables. I can reproduce it consistently by broadcasting a WM_SETTINGCHANGE message (I wrote a one-line C++ program to do this). Watching the activity in Process Monitor shows that explorer.exe doesn't even look at HKCU\Environment. What is going on?

  Read the article

• I get "An error occurred while Windows was synchronizing with [name of time server]." when trying t

  - by ChrisF

  Prompted by the answers to this question I decided to give the Windows built in time synchronisation another go. However, no matter what time server I use I get this error: "An error occurred while Windows was synchronizing with [name of time server]." The help suggests the following as reasons for failure: You are not connected to the Internet. Establish an Internet connection before you attempt to synchronize your clock. Your personal or network firewall prevents clock synchronization. Most corporate and organizational firewalls will block time synchronization, as do some personal firewalls. Home users should read the firewall documentation for information about unblocking network time protocol (NTP). You should be able to synchronize your clock if you switch to Windows Firewall. The Internet time server is too busy or is temporarily unavailable. If this is the case, try synchronizing your clock later, or update it manually by double-clicking the clock on the taskbar. You can also try using a different time server. The time shown on your computer is too different from the current time on the Internet time server. Internet time servers might not synchronize your clock if your computer's time is off by more than 15 hours. To synchronize the time properly, ensure that the date and time settings are set close to your current time in the Date and Time Properties in Control Panel. Now the first reason is clearly wrong - I am connected to the internet. I can see the 2nd being the most likely cause. I have Sygate Personal Firewall running, but it normally asks if something it trying to connect for the first time. Does anyone know I can unblock the NTP protocol - or at least check if it is blocked?. I don't think it's #3 or #4 as I've tried a number of different servers including the one currently used by Atomic Clock Sync. Though if someone knows the address of a UK time server I can double check this.

  Read the article

• Prevent Outlook 2010 Insert Picture resizing image

  - by Rup

  When I "Insert Picture" a JPEG in Outlook 2010 it automatically resizes the image and, I think, recompresses it too. I realise this would be useful for photographs or for people who try to email 1MB BMPs but I would like to email around an image at the original pixel size without recompression. Is there a way to turn this off, or better still choose settings for each image insert? I found this page in the Office help. It's for Word, PowerPoint and Excel not Outlook but points you at File, Options, Advanced, Image Settings. There's no equivalent section in Outlook. I know Outlook uses Word as its editor so I've looked at Word's settings but there isn't an 'original size' here: there's only 'turn off image recompression' and pick target DPI from 96, 150, 220. I guess Office is finding a DPI value in the JPEG file and scaling it up or down to match this setting. I can't find an equivalent option in Outlook's options menu but there's so many settings and pop-up dialogs I may have missed something. Picture Format, Reset image size resets the image to the rescaled version, not the original. I can't see a way to edit a pixel value into size values in the image properties after insert. Thanks! I realise I can probably achieve this by editing the image metadata in PhotoShop elements or similar but there ought to be a way without editing the file? This is new behaviour in Outlook 2010; 2007 didn't do this.

  Read the article

• How to host multiple FLEX applications in IIS7

  - by Devtron

  Hello, I manually deploy a FLEX application to my web server (IIS 7). There are two virtual directories, 1.) Default 2.) myFlexApp1. myFlexApp1 is where my working FLEX application resides. I now need to deploy a different FLEX application (let's call it myFlexApp2) to the same web server. I set up a virtual directory for [myFlexApp2] and it complains about the "bindings" using port 80, which is already used by [myFlexApp1]. I have tried to give them separate host names in their bindings properties. For example, myFlexApp1.mydomain.com and myFlexApp2.mydomain.com. I can never get [myFlexApp2] to show from an external browser. I was able to get only one or the other to display, but never could run both. Here is what I need: myFlexApp1.mydomain.com -- myFlexApp1 calendar.mydomain.com -- myFlexApp2 test.mydomain.com -- myFlexApp1 where test.mydomain.com is the default URL. Is this possible? What am I doing wrong? I even tried to edit the hosts file in [C:\Windows\System32\drivers\etc] but that didnt work either. How can I serve up two FLEX applications on IIS 7? It shouldn't be this hard!

  Read the article

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

• Virtual Machine Network Services causes networking problems in Vista Enterprise 64 bit install

  - by Bill

  I have a Quad-core/8GB Vista Enterprise 64-bit (SP2) installation on which I installed Virtual PC 2007. I have a problem that is opposite of all that I found searching around the Internet--everybody has problems making network connections from their guest VM. When Virtual Machine Network Services is enabled in the protocol stack for my network card across a reboot, it causes access problems to the network. The amount of time to login in using a domain credentialed account is upwards of 3 minutes, then after reaching the desktop the network and sharing center shows that my connection to the domain is unauthenticated. Disabling and re-enabling the Virtual Machine Network Services (uncheck in network properties/apply/recheck/apply) fixes the problem. And as long as I have the VMNS disabled when I shutdown the restart runs smoothly. I just have to remember to enable after login and disable before shutdown. I have un-installed and re-installed Virtual PC 2007 multiple times with restarts between. The install consists of the SP1 + a KB patch for guest resolution fix. Any help would be greatly appreciated. Some additional information... At one point during my hairpulling and teethgnashing with this, I tried to ping my primary DC and observed some weird responses: (Our DC is 10.10.10.25, my dynamic IP was 10.10.10.203) Reply from 10.10.10.203, Destination host unreachable. Request timed out. Reply from 10.10.10.25: ... This is not consistently repeatable, but thought it might strike a chord with someone.

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  Hi All, I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: http://superuser.com/questions/12955/how-do-i-remove-the-option-to-eject-sata-drives-from-the-windows-7-tray-icon

  Read the article

• Scripted forwarding for Outlook 2003

  - by John Gardeniers

  We have a staff member in sales who has gone onto a 4 day week (getting ready for retirement), so each Thursday afternoon her email needs to be forwarded to another user and each Friday afternoon it needs to be set back. I'm using the VBS script below to do this, run via the Task Scheduler. Although the script appears to do it's job, based on what I see when I view the user's Exchange settings, Exchange doesn't always recognise that the setting has changed. e.g. Last Thursday the forwarding was a enabled and worked correctly. On Friday the script did it's thing to clear the forwarding but Exchange continued to forward messages all weekend. I found that I can force Exchange to honour the changed setting be merely opening and closing the user's properties in ADUC. Of course I don't want to have to do that. Is there a non-manual way I can have Exchange read and honour the setting? The script (VBS): ' Call this script with the following parameters: ' ' SrcUser - The logon ID of the suer who's account is to be modified ' DstUser - The logon account of the person to who mail is to be forwarded ' Use "reset" to clear the email forwarding SrcUser = WScript.Arguments.Item(0) DstUser = WScript.Arguments.Item(1) SourceUser = SearchDistinguishedName(SrcUser) 'The user login name Set objUser = GetObject("LDAP://" & SourceUser) If DstUser = "reset" then objUser.PutEx 1, "altRecipient", "" Else ForwardTo = SearchDistinguishedName(DstUser)' The contact common name objUser.Put "AltRecipient", ForwardTo End If objUser.SetInfo Public Function SearchDistinguishedName(ByVal vSAN) Dim oRootDSE, oConnection, oCommand, oRecordSet Set oRootDSE = GetObject("LDAP://rootDSE") Set oConnection = CreateObject("ADODB.Connection") oConnection.Open "Provider=ADsDSOObject;" Set oCommand = CreateObject("ADODB.Command") oCommand.ActiveConnection = oConnection oCommand.CommandText = "<LDAP://" & oRootDSE.get("defaultNamingContext") & ">;(&(objectCategory=User)(samAccountName=" & vSAN & "));distinguishedName;subtree" Set oRecordSet = oCommand.Execute On Error Resume Next SearchDistinguishedName = oRecordSet.Fields("DistinguishedName") On Error GoTo 0 oConnection.Close Set oRecordSet = Nothing Set oCommand = Nothing Set oConnection = Nothing Set oRootDSE = Nothing End Function

  Read the article

• Disable or remove filter driver for single HID device

  - by snoopen

  Running Windows XP in a corporate setting here. I have an issue where a filter driver is interfering with the functionality of different USB HIDs. For example graphics tablets do not respond while the filter driver is in place. I've also had the issue with foot pedals used with transcription software. My question is really two fold: A) what makes Windows use a filter driver on one HID but not another? B) when a filter driver is causing conflicts how can I disable it on the affected devices? Background I've previously narrowed down the issue to the filter driver by uninstalling the software (Funk Proxy Host) responsible for the filter driver. The software is a type of RDP we use here at work. (I might have even booted into safe mode and renamed the file, I forget). I believe the filter driver is present to disable or modify the use of the local keyboard and mouse while admin staff are assisting users. Either way I don't have the authority to just go uninstalling this software. As far as I can tell the software versions are the same, however I'm not sure if the device driver definitions are all the same as I don't know where these things would be located. To check for the presence of the filter driver I locate the hardware device in Device Manager, click Properties Driver tab Driver Details.... It shows up as ph32ihid.sys. Even though all machines are meant to have the same SOE and do have Funk Proxy Host installed I don't always have issues with the same HIDs. A few machines here the foot pedals without any issues. I've not had any machines work with the graphics tablet without uninstalling Funk software. Driver details I've just read up a bit more about filter drivers and found the drivers description in the registry under "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\ProxyHostHIDFilter" There it's called "Kernel-mode HID filter driver for the Proxy Host". Presumably I could also disable it here but that would be system wide which is probably not desirable?

  Read the article

• SQL 2008 R2 replication error: The process could not connect to Distributor

  - by Lance Lefebure

  I have two servers running SQL 2008 R2 Standard, each with an instance named "MAIN". I have a small test database on my primary server (one table, 13 rows) that I want to replicate to a second server as a proof-of-concept for some larger databases that I want to replicate. I set up the primary server to be a publisher and distributor, and set the database to do transactional replication. I copied the data to the second server via a backup/restore, not via a snapshot (which I'll have to do with the larger databases due to database size and limited bandwidth). I followed the instructions here: http://gnawgnu.blogspot.com/2009/11/sql-2008-transactional-replication-and.html Now on the subscriber, I go under Replication / Local Subscriptions / Right click / Properties on my subscription to the DB. The status of the last synchronization shows a status of: "The process could not connect to Distributor 'PRIMARYSERVER\MAIN'." Data IS replicating from the primary to the secondary. Any record I add on the primary shows up on the secondary server within seconds. Is the Distributor part of the Snapshot system that I'm not using, or is it part of the transaction replication stuff? Thanks, Lance

  Read the article

• Why is my hg workbench & Adobe Reader toolbar icon a blank white page?

  - by Zasurus

  On my work's PC (windows 7 32bit) all Adobe Reader and hg Workbench icons on the toolbar (and general shortcuts for hg workbench) are just white pages (with the top left corner folded over). If you right click on the toolbar icon then right click on "TortoiseHg Workbench"(for hg workbench) then "Properties" then the "Change Icon..." button is greyed out (same for "Adobe Reader X"). Also the "Target:" is "TortoiseHg 2.4.0 (x86)" and is greyed out also the "Open File Location" is greyed out. This is the same for both Hg Workbench and Adobe Reader and seems to be the only thing that connects them. I have tried reinstalling to no avail. I also have local admin rights on the PC. I finally I have tried the following following questions without any luck (they aren't quite relevant to my issue but close): Adobe Reader program icon and pdf icons don't appear in Windows 7 Adobe PDF icon disappeared? Encase my description isn't enough to understand the issue here is a screenshot. As you can see the Hg Workbench icon (far left) and a pdf open in Adobe Reader X (second icon to from the left) are both blank and the shortcut is mainly greyed out.

  Read the article

• Menu command stuck on screen

  - by 280Z28

  For some reason, periodically when I select a menu command, the command label gets "stuck" on the screen and won't go away. I can close all open applications, including whichever one I was using when it got stuck, but it still won't go away. In the screenshot below, I opened an new instance of IE just to show how the label stays on top. The label was not created by this instance of IE. Edit with the source: The label that gets stuck is the first menu command I select in IE. If a label is already stuck, a new one does not get stuck (regardless of which instance(s) of IE are involved). Based on this knowledge, I now just open IE on my secondary monitor, carefully open the context menu so the Properties command is in the bottom corner, and click it. This is not a solution... The label never moves and is transparent to mouse input (if I click it, it's as if I clicked the item behind it). The label does not go away if I close all running applications. I haven't tried stopping services or closing system tray items like Live Mesh. The label does go away if I change the screen resolution and then change it back. Any ideas how I can stop this from happening? It's happened a half dozen times since yesterday and it's becoming quite disrupting to my work. Obviously I added the circle in MS Paint. That part isn't stuck. ;)

  Read the article

• Distributed storage and computing

  - by Tim van Elteren

  Dear Serverfault community, After researching a number of distributed file systems for deployment in a production environment with the main purpose of performing both batch and real-time distributed computing I've identified the following list as potential candidates, mainly on maturity, license and support: Ceph Lustre GlusterFS HDFS FhGFS MooseFS XtreemFS The key properties that our system should exhibit: an open source, liberally licensed, yet production ready, e.g. a mature, reliable, community and commercially supported solution; ability to run on commodity hardware, preferably be designed for it; provide high availability of the data with the most focus on reads; high scalability, so operation over multiple data centres, possibly on a global scale; removal of single points of failure with the use of replication and distribution of (meta-)data, e.g. provide fault-tolerance. The sensitivity points that were identified, and resulted in the following questions, are: transparency to the processing layer / application with respect to data locality, e.g. know where data is physically located on a server level, mainly for resource allocation and fast processing, high performance, how can this be accomplished? Do you from experience know what solutions provide this transparency and to what extent? posix compliance, or conformance, is mentioned on the wiki pages of most of the above listed solutions. The question here mainly is, how relevant is support for the posix standard? Hadoop for example isn't posix compliant by design, what are the pro's and con's? what about the difference between synchronous and asynchronous opeartion of a distributed file system. Though a synchronous distributed file system has the preference because of reliability it also imposes certain limitations with respect to scalability. What would be, from your expertise, the way to go on this? I'm looking forward to your replies. Thanks in advance! :) With kind regards, Tim van Elteren

  Read the article

• Frequency of RAM

  - by Vignesh Palani

  I have a very old system hp compaq dx2080. It had 1gb of RAM. I recently bought a EVM DDR2 1 GB PC RAM which had a clock rate of 667Mhz. I have dual booting windows 7 and 8. When I installed it, windows 7 was still using the older 1gb. It showed as 2 gb available and 1gb usable in system properties. I searched around and found that I can change it to max in the msconfig. I did so. I set it 2048. Still, it was using only 1gb. When, I switched to 8, it was using the 2gb. Now, for my question: My system only supported 553Mhz and 667Mhz RAM. In the BIOS, I saw that the new RAM was showing as 800Mhz. Rechecked using speccy and cpu-z. It showed different values between the two. The RAM is labeled as 667Mhz over it. No mistake in that. But, am I missing something? Please help. And, can I continue using it? My point again. There are only two slots.

  Read the article

• Why does the screen resolution of 1440x900 suddenly disappears from Intel GMA Control Panel?

  - by GeneQ

  I'm using a Vostro 1200 laptop with the Mobile Intel(R) 965 Express Chipset powering its graphics and running Vista 32-bit SP2 . I've been using the Vostro with a Dell SE198WFP LCD Monitor as the external display since day one for about two years without any problems. Recently, I plugged the Vostro into a couple of other monitors. The problem is, now the native resolution for my main monitor's (the SE198WFP) resolution of 1440x900 @ 60 Hz is no longer available. (See below) I've tried everything from uninstalling and reinstalling the Intel drivers as well as the monitor drivers to no avail. I've Goggled that this problem and it appears that this has happened to other people but all the answers involve people giving up in frustration or reinstalling; both terrible outcomes. Has anybody ever figured why this happens and have a good solution? Thanks. UPDATE: This dude has a complicated solution, which I haven't tried yet. His explanations for the problem was After an exausting search for an answer to the matter of why my brand new 19? widescreen monitor’s native resolution (1440×900) was unavailible (sic) in the display properties, I finally stumbled upon an article a person posted on Intel’s forums that basically explained what shannanigans Intel had been up to with their GMA 950 line of onboard graphic solutions. Not very comforting.

  Read the article

• Persistent PuTTY sessions for multiple windows

  - by Tgr

  I'm working in various Linux environments through PuTTY connections which break from time to time. I'm looking for a solution to make the PuTTY windows persist (e.g. if I was editing a file, then after reconnecting I should be in the same editor with the same file open at the same place), with the following requirements: it shouldn't require any manual setup at the beginning of the session or after reconnection (I don't want to type in screen or anything like that) I have several windows open to the same machine with the same user, which tend to disconnect at the same time the number/role of windows is not constant (it's not like I have an mc window, a mysql window and a "script runner" window; sometimes I use one window for search or for SVN commands, other times I need several at the same time) sometimes I need to change the properties of the windows for a task (large window for grepping/editing, small windows because I need to see two of them at the same time, red background because I am modifying the live database in MySQL etc), so I need to get the same console back in the same window after a reconnect Is there a way to achieve this? I suppose I should use screen or something equivalent, but how does it know which window I am reconnecting from? Is there some way to pass a unique window identifier to the shell from PuTTY?

  Read the article

• Parallels 6 - Is It Just Me or Does It Run Really Slowly?

  - by 5arx

  I've been running Parallels since version 2 with great success. I use it as my .Net development environment and over the last few years have converted so many others to the Parallels/Mac way of doing Windows/.Net development that I feel I should be getting perks/gifts and/or freebies from Parallels Corporation ;-) A month or so ago I upgraded to version 6 and ... immediately wished I hadn't. I'm currently running it on a laptop - a 2009 MacBook Pro (13"/2.53Ghz/4GB) while my MacPros at work and home are still running v5. I have seen nothing in v6 that makes me want to upgrade the install on those. The general problem is performance - upon starting or suspending a vm (always Windows 7 Ultimate), OS X slows down, quite often freezing for a minute or two at a time. The performance of the vms themselves are fine, but for me the point of this set-up is to be able to do web-browsing, email checking etc. on the OS X side of things while doing the stuff that can only be done on Windows (Visual Studio, SQL Server tools) on Windows. I have been using Parallels for a while so at least feel like I know what I'm doing so at the moment I am heading towards forming an opinion that its Parallels thats to blame. I've tweaked and tweaked all the vm configuration properties but to no avail. Support emails to the company have all received replies - there are no documented case of the issue you mention. Has anyone else seen this problem and if so, have you found a fix?

  Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >