Search Results

Search found 15661 results on 627 pages for 'protected mode'.

Page 361/627 | < Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >

• Any way to stop VMWare workstation from dropping SSH connections?

  - by oljones

  I have VMWare workstation 8 with a few Linux guests. I have had problems maintaining an active SSH connection to my VMs when they are in bridged mode. I first read that the onboard realtek network cards were not well supported so I bought a Intel Pro/1000 GT card. This supposedly had support. But this made no difference. Connections via SSH are active for about the first 3 minutes then hang and die. I have changed the TCP Checksum offload on the Intel and Realtek NICs, but this only works some of the time and even then not for very long. The best I could do was about 20 minutes before the connection was dropped. Any ideas?

  Read the article

• PC boots on then off & 30 sec. later on again, it wiil shut off on itself mostly in idle or just unexpecticly

  - by Jody

  This problem started w/ my sons desktop, it would just shut off after a bit of work or stay on for a long time & to get it to unfreeze is to cold boot it, i put a new HDD in & I still have the same issue, RAM is good power supply fan is moving quite as well as all the rest of the fans it has stayed fairly dust free, i'm at a loss ,I have defaulted all the factory settings changed battery & ungraded to a new OS. I still have the same problem. the power light stays on after it has shut down & when upon starting it goes straight to safe mode option page, I start in last good config. reboots again takes 30 sec. to boot & will work again for a while, the only other thing I haven't tried was a graphic card replace, i'm onboard video now & have been.

  Read the article

• Google Chrome doesn't stay logged in to Google sites when using pinned tabs

  - by Nick T

  Despite checking "stay logged in" or the like on Gmail or Docs, Chrome refuses to do so when I close and re-open it with Google sites pinned. If they're not pinned, it works fine. The "Clear cookies and other site and plug-in data when I close my browser" checkbox in the settings is not checked, and I don't have any cookie exceptions. All settings are defaults. Nor is the incognito mode being used. This occurs on all my computers using Chrome. I have deleted my cookies file (%userprofile%\AppData\Local\Google\Chrome\User Data\Default\Cookies) with no effect (other than losing the logins that ordinarly work fine). Of note is that when I relaunch Chrome with Gmail pinned and it asks me to log in, doing so once will fail (does nothing; no errors), then it will work on the second attempt. If I refresh the window before doing so, it will work on the first attempt.

  Read the article

• Cinema4D for game development tutorials anyone ?

  - by George Profenza

  Hi, I started to learn Cinema 4D. I've noticed it's really easy to use for motion graphics, but I want to use it for modeling for games/realtime 3d engines. Before I used 3dsmax and it was easy to estimate how a model would look/behave in a 3d engine. The two main things I did was displaying Polygon triangles and displaying the Polygon Count. I've found the Total Polygons tick in HUD settings in Cinema 4D, but I can't find any display mode that will show triangles. Is there there a way to display triangle faces/not quads in Cinema4D ? If so how ? There is a Triangulate function, but I'd rather not Triangulate/Untriangulate all the time, especially since it's converting back and forth between the two doesn't always produce the same result.

  Read the article

• How to get full write permission on my second drive after dual boot?

  - by Shaul

  I had a WinXP installation on my hard drive. Then I bought a 2nd drive and installed Win7. Dual boot working fine. But when I'm in the Win7 environment, it appears that I don't have full admin permission on the "D" drive (that's the drive with WinXP). Even though the user I'm logged in as has admin permissions, I have to run my apps with administrator privileges in order to get write access to the D drive. This is not the case when I do stuff on the C drive. I could just get into running those apps that access the D drive in admin mode, but that seems like overkill. Is there some secret switch I can flip so that my D drive acts like my C drive, security-wise?

  Read the article

• How to ask Debian not to check last mount time of its file system?

  - by Landy

  I'm using Debian 6.0.5. To test a feature of my product, I need to modify the system date&time back and forth frequently. Once a time I set the system date back to one month ago, then I reboot the system, and it reported the last mount time of the file system is in the future and enter the maintenance mode automatically. I had to run the fsck to make sure the file system is not broken to boot into Debian. Is there any way to ask Debian stop checking the last mount time of its file system when booting? Thanks.

  Read the article

• Windows 8 store freezes when searching for updates

  - by Roger

  I'm running Windows 8 Pro (x64) on my home desktop. Everything is working well (very very differently, but well) except for the Store application. Several days ago, I got an update notification that listed 8 application updates. I hit the link to install the updates, but only six of them installed. Now I have Updates(2) showing in the store's notification area, and whenever I try to look for the updates the Store goes into "searching" mode (the circles/dots animation) and never finishes the search. Is there any way that I can reset the Store app? I have tried re-downloading it with no success.

  Read the article

• Fujitsu Siemens V6535 laptop doesn't wake up - crash when going into standby?

  - by marc

  I'm having trouble with my laptop (Fujitsu Siemens model V6535). It runs Windows 7, and after I upgraded from Vista I've noticed something that makes me really angry. When my laptop goes into Standby, the power LED changes to red and starts blinking (standby mode). When I push the power button to wake it up it, the blinking LED changes to green but nothing else happens. Nothing on the display, no HDD sound. When I press the power button for a few seconds and then try turn it on again, it doesn't display anything. I have to unplug the charger, shut it off, and power it on again without the power cable. Then it starts working. A few days ago I upgraded the BIOS to the newest version, but it doesn't help. Does anyone have any idea what can be wrong?

  Read the article

• GPU Computing - # of GPUs supported

  - by TehTypoKing

  I currently have a desktop with 6 GPUs ( 3x HD 5970s ) in non-crossfire mode. Unfortunately, it seems that Windows 7 64bit only supports up to 4 GPUs. I have not been able to find a reliable source to deny or confirm this. If windows 7 has this limitation, is there a Linux flavor that supports more than 4 GPUs? In-case you are wondering, this is not for gaming but high-speed single precision computing. With this current setup ( if I can find 6gpu support ) I am looking to reach 13.8 Teraflops. Also, my motherboard does support 3 16x pci-xpress gen2 slots... and I have a 1500w powersupply plugged into a 20amp outlet. Windows is able to detect all 6 cores.. although, 2 of which displays the warning "Drivers failed to load". To recap: - Can windows support 6 GPUs? - If not, does Linux? Thank you.

  Read the article

• Is there any way to use devices like mp3 players when they are charging?

  - by GeoB

  The question is simple I think. All we have encounter gagets that they don't fuction while they are in charge, like cameras or mp3 players. But, we know that cell phones or laptops can have full function, when they charge with a charger, like USB connector. Is it in the programming? Why this happens? Can we change that with some device e.g. controlling the charging? I want to use a portable USB charger for my mp3, but I can't wait 3 hours for it to charge, because I cannot listen to music. It notices the charger, and gets in charge mode. Nothing functions until I unplug it. Thanks a lot

  Read the article

• puppet agent doesn't retrieve files from master

  - by nicmon

  I have a very basic question regarding to Puppet 3.0.1 configuration. I setup a puppet master server (CentOS) with 2 agents (CentOS and Windows 7), all 3 can ping and access each other. There is no error at all. I have copied a file under /etc/puppet/files/test2.txt my site.pp (/etc/puppet/manifests) contains these lines: node default { include test file { "/tmp/testmaster.txt": owner => root, group => root, mode => 644, source => "puppet:///files/test2.txt" } } but there will no file be created on agent servers under /tmp/ once I run "puppet agent --test" here is the output: [root@agent1 ~]# puppet agent --test Info: Retrieving plugin Info: Caching catalog for agent1.mydomain.com Info: Applying configuration version '1354267916' Finished catalog run in 0.02 seconds "puppet apply /etc/puppet/manifests/site.pp" creates the testmaster.txt under /tmp/ on master.

  Read the article

• Ubuntu server 12.04.03 not checking disk partitions on reboot?

  - by jamesc

  My MOTD is showing: *** /dev/md2 will be checked for errors at next reboot *** *** /dev/md1 will be checked for errors at next reboot *** *** /dev/md3 will be checked for errors at next reboot *** However, a standard sudo shutdown -r now does not appear to check the disks and the message remains. My guess is that the partitions 'should' be checked and that they are not being... so how can I get Ubuntu to check the partitions at reboot and keep things nice and safe? Update - this is the output of cat /etc/fstab proc /proc proc defaults 0 0 none /dev/pts devpts gid=5,mode=620 0 0 /dev/md/0 none swap sw 0 0 /dev/md/1 /boot ext3 defaults 0 0 /dev/md/2 / ext4 defaults 0 0 /dev/md/3 /home ext4 defaults 0 0 Update 2 - One message gone... Using @christianwolff's suggestions... sudo rm /var/lib/update-notifier/fsck-at-reboot sudo touch /forcefsck sudo shutdown -r now And now the motd is down to *** /dev/md1 will be checked for errors at next reboot *** *** /dev/md3 will be checked for errors at next reboot *** So 'md2(ext4)' has been checked and the message updated.

  Read the article

• Netcat UDP File Transfer Between Two Servers Times Out?

  - by Mark Bowytz

  I'm testing file transfer speeds between two Red Hat servers that are connected to the same switch within the data center and I decided to use netcat to eliminate protocol overhead as much as possible. Testing in TCP mode went well and I was wondering how UDP might fare. On my receiving (client) end, I ran this: nc -u -l 11225 -v > myfile.out And then on the sending (server) end I ran the following: cat myfile.out | nc -u myserver.foo.zzz.com 11225 -v The file I'm testing with is 38 GB but the transfer seems to stop at around 15 GB (one time at 14.9, another at 15.6). I've tested by adding a "-w 5000" just in case it's timing out but no joy. Adding the -v doesn't show anything except acknowledging that the connection occurred. No errors. So - any suggestions as to why would the transfer cease?

  Read the article

• CentOS-Like configuration of Vim on Ubuntu

  - by matejkramny

  Whenever I use a CentOS System, there's always a pleasant configuration of vim which mainly does the following: Remembering position of closed files Colour mode (!!!) Bash has colours There's lots more, just not something i can recall on the spot. Then, i go to ubuntu and its all black and white, no nice vim config etc. I have to use Ubuntu, and I hate ubuntu because of this. I know I can all configure it by myself, so my question is: How can I configure the Ubuntu system to behave (aesthetically) like CentOS? PS to future self: I will be stoned to death for asking such a question.

  Read the article

• My iPhone is stuck at screen with USB cable and iTunes logo

  - by alex

  I just tried updating the iPhone's firmware, and things went haywire. iTunes informed the update had failed and linked me to this page. The iPhone is stuck on the image from the top of that page. I held down the sleep and home buttons until it turned off and turned it back on, and then went through the iPhone's 'restore' mode. It then error'd again and I'm stuck back with the logos on the iPhone. Does anyone know how to fix this? Thanks

  Read the article

• Windows 2008 Server Unable to activate with other methods

  - by matt king

  I'm trying to activate windows 2008 server SP2 today since the activation trial is done. I do not have an internet connection with this server so I can not activate online, and with the other servers in this farm I've been able to run the slmgr -ipk xxxxx-xxxxx-xxxxx-xxxxx-xxxxx and then it would open up the activate by phone method and we would just activate that way. I say again, I don't have an internet connection so I can not do the online activate. If I do the slui 4 it brings up the activation window but show me other ways to activate is still greyed out. I've disabled the NIC on this Hyper-V server and I still can not get the other way to activate to show up... Anyone have any ideas? This computer is one of my AD servers so.. it being in notification mode kind of sucks. Thanks.

  Read the article

• WSS "Cannot connect to the configuration database"

  - by Tim

  I have 64-bit WSS 3.0 installed on a 64-bit Windows 2003 Server. After installing WSS 3.0 I switched IIS to run in 32-bit emulation mode as we have some applications that require this. I'm getting a "Cannot connect to the configuration database" trying to get to the Central Admin page and wondered if: a. The setup I have won't work and I'm wasting my time trying to figure this out. or b. If anyone has any suggestions for resolving the database connection issue? The identity of the app pool that WSS runs under has all the required permissions in SQL so far as I can tell. Any help would be appreciated!

  Read the article

• AWS:EC2:: Could not connect FTP client?

  - by heathub

  My Server OS: Amazon Linux I am trying to set up ftp. I have: Installed vsftpd open port 20-21 open port 1024 - 1048 Basically, I followed every of these steps Start vsftpd service (the status indicate [ok]) I use filezilla for my ftp client. Here is my setting/configuration: Host: ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Port: -(blank, but I have tried 20 and 21 though) Server Type: FTP - File Transder Protocol Logon Type: Normal Username: (tried root and ec2-user) Transfer mode: Tried passive and active I always has this error: Status: Waiting to retry... Status: Resolving address of ec2-XX-XX-XXX-XX.compute-1.amazonaws.com Status: Connecting to XX.XX.XXX.XX:21... Error: Connection timed out Error: Could not connect to server Have I missed any configuration/settings? EDIT After execute the /sbin/iptables -L -n Here is the result: Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Can GNU sed (for Windows) handle Unicode? If so, is it a code-page/locale issue, or a switch?

  - by Peter.O

  I've been using GNU SED on and off for a couple of years now. It spins me out a bit sometimes, but it does a good job... for single-byte char sets! I now and then notice references to GNU SED being Unicode-aware, but the closest I've seen of this is its "binary" mode.. and binary is not Unicode. Can GSED process a Unicode text file at CodePoint resolution, including and especially \r\n (Windows)... and if it can, does it expect UTF-8, UTF-16, or what? and how does SED detect the encoding?

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Cisco RV016 dual WAN and VPN setup

  - by sklr

  I have a VPN of several RV016 routers and I want to set some of them with 2 ISPs. I plug the two ISP cables in WAN 1 and 2 ports and configure the router to "Intelligent Balancer(Auto Mode)". It works ok like that, but the VPNs that I set use the public IP of the provider. For example if I have 5 VPNs set for ISP1 (WAN1) and the balancer sends the request trough WAN2 it can't use any of the configured VPNs because the public IP is different. How do I deal with this problem?

  Read the article

• Default audio device gives an error on WINDOWS 7 (x64) when triing to run VLC from CMD (VideoLAN, VL

  - by Ole Jak

  I use WINDOWS 7 (x64) (Russian) I want to stream life audio from my default audio capture device (microphone) When I set up VLM settings using visual enviroment instruments - VLM settings it all works fine. But when I export created settings/configuration *.vlm file and try to inport it into VLM it gives me nothing I opened that .vlm there is some text... so now I try to run VLC with default settings like this: vlc -i dshow:// --dshow-adev= :sout=#transcode{acodec=mp3,ab=128,channels=2,samplerate=44100}:std{access=http,mux=raw,dst=127.0.0.1:8084} but it dies giving me errors...=( So what shall I do to do live MP3 streaming from my default audio input device using VLC in non UI mode?

  Read the article

• What would you use to keep track of all the random information about your LAN/Enviroment?

  - by agnul

  Say you work in your average anarchy... no appointed IT guy, no Office-Manager whatsoever, just developers working in free-for-all mode and a couple of non technical people around for admin (non IT) stuff. What would you use to keep track of Hardware / Software inventory Backups of OS images, Drivers, and all that LAN configuration information Passwords for all the systems Currently I'm thinking of having some sort of wiki + web server on our only ''server-class'' machine, but then I fear I'd be the only one who would go through the hassle of adding information in the wiki... So, have you been through that? What would you suggest?

  Read the article

• Cannot write, format, nor erase flash drive

  - by Baruch

  I have a 4gig flash drive, which I can read from but not write on, erase, nor format in any computer (tried in 7 different computers including xp, vista, and win7). I want to erase all the data inside because it is useless. Once I erase something, it erases it and gives me an error that it can't find the file. Once I refresh the folder, the file comes back. I tried holding Shift + Del. I also tried to use the command to format it in safe mode, but it says "access denied". I don't have a write protection button or whatever it is on my flash drive. It's just a simple small 4 gig one.

  Read the article

• How to check use of userva boot option on Win 2K3 server

  - by Tim Sylvester

  I have some 32-bit Win2K3 servers running an application that fails now and then apparently due to heap fragmentation. (Process virtual bytes grows, private bytes does not) I do not have access to the source code or build process of this application. I have modified the boot.ini file on one of these servers to include /userva=2560, half way between the normal mode of operation and the /3GB option. Normally it takes weeks to reach the point of failure, but I'd like to see right away whether this has actually had any effect. As I understand it, this option limits the kernel to the remaining address space (1536MB instead of 2048), but does not necessarily give an application the extra address space, depending on the flags in the application's PE header. How can I determine whether the O/S is allowing a particular application, running in production, to access address space above 2GB? Additionally, what's the best way to monitor the system to ensure that the kernel is not starved for address space, and more generally how should I go about finding the optimal value for this setting?

  Read the article

< Previous Page | 357 358 359 360 361 362 363 364 365 366 367 368  | Next Page >