Search Results

Search found 10388 results on 416 pages for 'hardware selection'.

Page 362/416 | < Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• 100% CPU when doing 4 or more concurrent requests with Magento

  - by pancake

  Currently I'm having trouble with a server running Magento, it's unbelievably slow. It's a VPS with a few Magento installations on it used for development, so I'm the only one using them. When I do 4 request all 2 seconds after each other I'm finished in 10 seconds. Slow, but still within the limits of my patience. When I do 4 "concurrent" requests, however (opening 4 tabs in a row, very quickly) all four cores go to 100% and stay there for like a minute. How is this possible? I know that there are a lot of possibilities here, so any tips on how to make an Apache/PHP server go faster are also welcome. It used to go a lot faster before, and I've also tried APC, but it kept causing problems (PHP errors, something with memory pools) so I've disabled it. By the way, the Magento cache is off and compiling is also off. I know this makes Magento slower than usual, but I don't think a 60 second response time is normal for any Magento installation. Virtual hardware: 4 Cores and 4096MB RAM Swap is never used (checked with htop) 100GB disk space, of which 10% is in use Software: Debian 6 DirectAdmin and apache custombuild PHP 5.2.17 (CLI) If you need more info, please tell me how to get it, because I probably don't know how. I do know how to use the command line in linux and the usage of quite a few commands, but my experience with managing a server is limited.

  Read the article

• How to minimize the risk of employees spreading critical information?

  - by Industrial

  Hi everyone, What's common sense when it comes to minimising the risk of employees spreading critical information to rivalling companies? As of today, it's clear that not even the US government and military can be sure that their data stays safely within their doors. Thereby I understand that my question probably instead should be written as "What is common sense to make it harder for employees to spread business critical information?" If anyone would want to spread information, they will find a way. That's the way life work and always has. If we make the scenario a bit more realistic by narrowing our workforce by assuming we only have regular John Does onboard and not Linux-loving sysadmins , what should be good precautions to at least make it harder for the employees to send business-critical information to the competition? As far as I can tell, there's a few obvious solutions that clearly has both pros and cons: Block services such as Dropbox and similar, preventing anyone to send gigabytes of data through the wire. Ensure that only files below a set size can be sent as email (?) Setup VLANs between departments to make it harder for kleptomaniacs and curious people to snoop around. Plug all removable media units - CD/DVD, Floppy drives and USB Make sure that no configurations to hardware can be made (?) Monitor network traffic for non-linear events (how?) What is realistic to do in a real world? How does big companies handle this? Sure, we can take the former employer to court and sue, but by then the damage has already been caused... Thanks a lot

  Read the article

• using i7 "gamer" cpu in a HPC cluster

  - by user1219721

  I'm running WRF weather model. That's a ram intensive, highly parallel application. I need to build a HPC cluster for that. I use 10GB infiniband interconnect. WRF doesn't depends of core count, but on memory bandwidth. That's why a core i7 3820 or 3930K performs better than high-grade xeons E5-2600 or E7 Seems like universities uses xeon E5-2670 for WRF. It costs about $1500. Spec2006 fp_rates WRF bench shows $580 i7 3930K performs the same with 1600MHz RAM. What's interesting is that i7 can handle up to 2400MHz ram, doing a great performance increase for WRF. Then it really outperforms the xeon. Power comsumption is a bit higher, but still less than 20€ a year. Even including additional part I'll need (PSU, infiniband, case), the i7 way is still 700 €/cpu cheaper than Xeon. So, is it ok to use "gamer" hardware in a HPC cluster ? or should I do it pro with xeon ? (This is not a critical application. I can handle downtime. I think I don't need ECC?)

  Read the article

• glusterfs mounts get unmounted when 1 of the 2 bricks goes offline

  - by Shiquemano

  I have an odd case where 1 of the 2 replicated glusterfs bricks will go offline and take all of the client mounts down with it. As I understand it, this should not be happening. It should fail over to the brick that is still online, but this hasn't been the case. I suspect that this is due to configuration issue. Here is a description of the system: 2 gluster servers on dedicated hardware (gfs0, gfs1) 8 client servers on vms (client1, client2, client3, ... , client8) Half of the client servers are mounted with gfs0 as the primary, and the other half are pointed at gfs1. Each of the clients are mounted with the following entry in /etc/fstab: /etc/glusterfs/datavol.vol /data glusterfs defaults 0 0 Here is the content of /etc/glusterfs/datavol.vol: volume datavol-client-0 type protocol/client option transport-type tcp option remote-subvolume /data/datavol option remote-host gfs0 end-volume volume datavol-client-1 type protocol/client option transport-type tcp option remote-subvolume /data/datavol option remote-host gfs1 end-volume volume datavol-replicate-0 type cluster/replicate subvolumes datavol-client-0 datavol-client-1 end-volume volume datavol-dht type cluster/distribute subvolumes datavol-replicate-0 end-volume volume datavol-write-behind type performance/write-behind subvolumes datavol-dht end-volume volume datavol-read-ahead type performance/read-ahead subvolumes datavol-write-behind end-volume volume datavol-io-cache type performance/io-cache subvolumes datavol-read-ahead end-volume volume datavol-quick-read type performance/quick-read subvolumes datavol-io-cache end-volume volume datavol-md-cache type performance/md-cache subvolumes datavol-quick-read end-volume volume datavol type debug/io-stats option count-fop-hits on option latency-measurement on subvolumes datavol-md-cache end-volume The config above is the latest attempt at making this behave properly. I have also tried the following entry in /etc/fstab: gfs0:/datavol /data glusterfs defaults,backupvolfile-server=gfs1 0 0 This was the entry for half of the clients, while the other half had: gfs1:/datavol /data glusterfs defaults,backupvolfile-server=gfs0 0 0 The results were exactly the same as the above configuration. Both configs connect everything just fine, they just don't fail over. Any help would be appreciated.

  Read the article

• Faster, secure, protocol/code required for long-distance transfer.

  - by Chopper3

  I've ran into a problem and I'm looking for a new secure protocol/client/server that's faster over a 1Gb/s fibre link - let me tell you the story... I have a pair of redundant, diversely-routed, 1Gb/s links over a distance of around 250 miles or so (not dark fibre but a dedicated point to point link, not a mesh). At the 'client' end I have a HP DL380 G5 (2 x dual-core 2.66Ghz Xeon's, 4GB, Windows 2003EE 32-bit), at the 'server' end I have a HP BL460c G6 (2 x quad-core 2.53Ghz Xeons, 48GB, Oracle Linux 5.3 64-bit). I need to transfer around 500 x 2GB files per week from the client to the server machines per week - but the transfer NEEDS to be secure. Using both iPerf or regular FTP I can get ~80MB/s of transfer pretty consistently, which is great. Using WinSCP or Windows SFTP I can't seem to get more that ~3-4MB/s, at this point the server's CPU is 3% busy while CPU0 of the client goes to ~30% utilised. We've tried editing various TCP window sizes with little success. Both ends are connected to quite low-usage Cisco Cat6509's with Sup720's. I can replace the client machine with a newer machine and/or move it to Linux - but this will take time. Clearly these single-threaded secure Windows clients are introducing too much latency doing their encryption. So a few questions/thoughts; Are there any higher performing secure protocols or client software for Windows that I could try? I'm pretty protocol-gnostic so long as it'll work between Windows and Linux. Should I be using hardware to do the encryption, either in the client or the network parts? If so what would you recommend? I'm not convinced that just swapping the server would be that much faster, the CPU was only at 30% but then again that's higher than I'd have expected given the load - moving to Linux at the client end may be a better idea but would be quite disruptive. Am I missing a trick? Thanks in advance.

  Read the article

• Recommended Smartphone for Reading PDFs [closed]

  - by mika

  This is as much a software than a hardware question. I use a lot of public transport and perhaps the best way to spend your time there is to read while listening to music. Currently I use Nokia E90 and Adobe Reader LE 2.5 (full version). I was wondering if there are any better alternatives? Requirements: at least 640px wide screen, preferably 800px physical size of the LCD display matters, it should be large, but the phone itself should be as small as possible. This favors touchscreen models PDF reader should be of high quality. It should render most PDFs correctly. Other important features include: full screen mode, keyboard controls for Page Down and page change, multiple zoom levels to adjust to the screen, opening recent documents at the last page read Downsides of E90 + Adobe Reader LE Phone is large compared to the display It is hard to read the display at sunlight Adobe Reader crashes the phone regularly, zoom could have more levels, doesn't remember last page EDIT: Switched to iPhone and GoodReader. Smaller physical screen width compared to E90 is a disimprovement, but other than that I'm happy. GoodReader is the highest quality smartphone PDF reader I've seen so far.

  Read the article

• CentOS Installation on a Cisco MCS 7800

  - by William

  Hello, I'm having some problems installing CentOS 5.5 Final (i386) Onto my server, a Cisco MCS 7800. The problem comes very early into the installation. When the welcome screen comes up ans gives you the option on how to boot into the DVD, Ill press enter to go into the graphical installer. The Screen will then have a blinking cursor in the top left of the screen and will never go away (I thought that it just might need time but I let it sit for over 5 hours.) I then booted into it again and tried using Linux Text thinking it was a problem with graphical installer. That didn't work, same problem. Then I tried a DVD of RHEL 5 and got the same problem, both graphical and Linux text. At this point i think its a hardware problem. The Server has 2GB of ECC RAM, 1 Pentium 4 CPU @ 3.06GHZ and 2 WD Hard Drives (80GB) Configured for RAID 0. ( Also there is a option in the BIOS for what OS type and that is set to Linux.) If anyone has any idea what is going on, it would be helpful. ================Edit================== ooshro, typing "text" doesn't change a thing. still stuck at the blinking cursor. I looked it up and its really the same thing as typing "linux text", which as stated in the first part of my question, i've already done.

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• Disk Activity Alert Windows SBS 2003 on Dell PowerEdge 830 with Raid

  - by Ron Whites

  Background: I have a Dell PowerEdge 830 Server running Windows SB Server 2003. It has 4gbs of RAM and a ATA CERC SATA 6CH controller with 3 160gb drives in a Raid 5 configuration. The Problem I am seeing Admin ---"Disk Activity Alert on Server" emails These often occur when disk backups, de-frag or high disk usage is going on. Generally the server isn't over stressed. The Disk Alert emails say in part ... The following disk has low idle time, which may cause slow response time when reading or writing files to the disk. Disk: 0 C: F: D: Review the Disk Transfers/sec and % Idle Time counters for the PhysicalDisk performance object. If the Disk Transfers/sec counter is consistently below 150 while the % Idle Time counter remains very low (close to 0), there may be a problem with the disk driver or hardware. The Questions I have: With what utility can I review the Disk Transfers/sec and Idle Time? It appears there is no utility for that on the server! I think I may need to download a very large (two DVD) Dell "OpenManage" utility to be able to monitor the raid system and see what is a problem is that true?

  Read the article

• High-performance Academic Server [closed]

  - by PHPsmith

  Suppose I want to build a server for the university's academic interests. The server is dedicated only to a site, where users (students and lecturers) just view and fill the academic data. But at a time (e.g. once a semester), about 12,000 students will access the site simultaneously. Due to limitation of resources, I have to build the server using free software (except for the operating system Windows 7, the university has been prepared). The hardware is also limited to the usual 4-core computers (eg, Ivy Bridge Intel Core i7-3770) with approximately 16GB of memory (DDR3 1600 MHz), equipped with an RJ-45 port (Intel 82 579 Gigabit Ethernet). With all these limitations, I have to choose the software (web server, database, etc) are appropriate for this purpose is achieved. I decided to create a site in PHP. Please help me by answering the following questions based on your expertise. (my prime candidate software to consider after googling) Web server which is faster & stable & secure, when implemented and optimized for PHP? And why? (nginx) PHP accelerator which is faster & stable & compatible with the selected web server? And why? (APC with Zend Optimizer+) Database which is faster & stable & secure, when implemented and optimized for selected web server and selected PHP accelerator? (MySQL) Are there any errors that have been or will be happening from my condition is? If there is, please enlighten me? Is there anything else I need to know in order to achieve this goal? If there is, please enlighten me? I understand that the performance also depends on the implementation of source-code program, so I assume it will create a site with the best efficiency (e.g. using AJAX).

  Read the article

• vSphere education - What are the downsides of configuring virtual machines with *too* much RAM?

  - by ewwhite

  VMware memory management seems to be a tricky balancing act. With cluster RAM, Resource Pools, VMware's management techniques (TPS, ballooning, host swapping), in-guest RAM utilization, swapping, reservations, shares and limits, there are a lot of variables. I'm in a situation where clients are using dedicated vSphere cluster resources. However, they are configuring the virtual machines as though they were on physical hardware. In turn, this means a standard VM build may have 4 vCPUs and 16GB or more of RAM. I come from the school of starting small (1 vCPU, minimal RAM), checking real-world use and adjusting up as necessary. Some examples from a "problem" cluster. Resource pool summary - Looks almost 4:1 overcommitted. Note the high amount of ballooned RAM. Resource allocation - The Worst Case Allocation column shows that these VMs would have access to less than 50% of their configured RAM under constrained conditions. The real-time memory utilization graph of the top VM in the listing above. 4 vCPU and 64GB RAM allocated. It averages under 9GB use. Summary of the same VM What are the downsides of overcommitting and overconfiguring resources (specifically RAM) in vSphere environments? Assuming that the VMs can run in less RAM, is it fair to say that there's overhead to configuring virtual machines with more RAM than they need? What is the counter-argument to: "if a VM has 16GB of RAM allocated, but only uses 4GB, what's the problem??"? E.g. do customers need to be educated? What specific metric should be used to meter RAM usage. Tracking the peaks of "Active" versus time?

  Read the article

• Linux kernel - can't access sda16 & sda17

  - by osgx

  I can't access sda16 sda17 and higher partitions from my linux. This linux is rather debian (very old); kernel 2.6.23. So, I know that so old linux kernel can't access 16 partitions on single sata disk. What version of kernel should I use to be able access sda16, sda17 etc? I want to update only a kernel, not a whole Linux distribution. PS. There is an WindowsNT kernel which can access and format 16, 17 or higher partition, but my intention is to use sda16 and sda17 from linux (I want Linux Kernel). PPS: dmesg: sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 > sd 2:0:0:0: [sda] Attached SCSI disk sd 4:0:0:0: [sdb] xxx 512-byte hardware sectors ... So, there is no mapping of sda16, sda17, ... to sdb. Sdb is the second physical hard drive.

  Read the article

• Windows 8 using as a webserver

  - by Jason

  I have a few hobby websites that I currently host on CentOS 6. Apache, mail serving, PHP, MySQL nothing special. In the past I used Windows XP to do this same task, for years, and I was OK. I switched to Linux and for the last few years it has been such a pain. updates break, certain apps only support certain distros without compiling from source. It prevents me from working on my hobby sites more because I am always fixing something. With Windows I locked it down, I run a hardware firewall and packet analyser, kept up on updates and A/V and never had a problem. I dont allow RDC from outside the local LAN, no FTP open, run OpenSSH on an obscure port.. I am considering switching to Windows 8 (since it is a cheaper license now that Windows 7) and running apache, HMailServer, PHP, MySQL, just like my CentOS install. My questions: I am not familiar with Windows 8, can the above be done like XP? No new security restrictions or the OS preventing this from happening? The machine is a Athlon 64-bit X2 with 32GB of RAM. Will Windows 8 see all of the RAM? Technically the machine came with Windows 7, and there is a serial number on it but I am sure I wiped away the Windows 7 recovery partition when I switched to Linux....

  Read the article

• Obtaining clear cable signal with Hauppage 1191-950Q TV Tuner

  - by Kyle B.

  I bought a Hauppauge 1191 WinTV-HVR-950Q TV Tuner a while back, and I am attempting to use it to watch TV in Windows Media Center. I do not have cable TV, however I used to have Comcast. Through experimentation, I found that connecting my coax cable into my TV, I was able to view television (i.e. 2-1 = CBS, 5-1 = NBC, etc). This also works on a second TV I use in another room. When I connect the coax cable to my TV Tuner stick and scan TV channels in Windows Media Center, it only picks up 1 station (like 81 or something). My only conclusion on this is somehow the hardware in the television is decrypting a signal that the TV tuner stick is not able to. Is that possible? Should I try a different TV tuner? Any assistance would be appreciated. I also bought a Terk HD Indoor Antenna but my reception has been flakey, so I would rather go this route if possible.

  Read the article

• Alfa AWUSO36H 1W dysfunctional driver

  - by BrainStorm

  I recently purchased an Alfa AWUSO36H 1W wireless USB adapter for my notebook, in order to improve signal strength and quality. I'm currently using Linux Mint 11, and the it uses the RTL8187 driver for this adapter, I'm also using a 4dbi antenna, though I have others. The problem is that this adapter does exactly the opposite of what it should, actually my internal Broadcom BCM4313 adapter works way better than the alfa. Browsing is slow, some network applications don't even work, pings against Google.com on the internal adapter runs smooth, while in the alfa it gets like 25% packets lost or more! I'm less them 50 feet from my AP, the internal adapter gets 44/70 link quality, and the alfa gets around 60/70 (iwconfig output). Also the system always sets alfa power to 20dbm(100mw), then I have to do sudo iw set reg B0 to make it 30dbm(1000mw), but apparently no significant change. I've installed wireless-compat drivers, no change either. And worst of all, in Windows 7 it works way more smoothly for browsing, though I couldn't test it properly there. I hope its a driver problem, even if it's a pain to find/compile Linux drivers for a starter, I prefer it to a hardware problem where I would need to buy another adapter, since I have no money left (except for the cantenna pieces).

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• HTC Diamond Touch sync problem

  - by Anders

  I have a HTC Diamond Touch with all my contacts etc. on it. Did however not use it for 6mo while being abroad. When I start the phone now I realize that the touch screen has stopped working. I have tried restarting, soft resetting, shutting it off etc but the touch just wont follow commands. However, I can manage the phone by buttons so it's not frozen. Hence I can get into the phone and watch contacts but not use it to call etc. The problem is, how do I get my 300 contacts out of the thing!? When I'm plugging in the phone, it lets me choose between "Sync with Outlook" and "Use as storage device". It automatically selects "Use as storage device". Now, I cannot choose to sync it with the buttons. I can not change this option afterwards either. In short, I have a phone with all of my contact data and am completely unable to get that out of it. Any tips/help/suggestions? If possible, preferably one that does not including sending the phone to a hardware workshop for three weeks in order to get it fixed:)

  Read the article

• How to monitor bandwidth use of each device on wifi network

  - by GWLlosa

  I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Two screens hooked to one laptop

  - by mplacona

  Hi, I'm thinking of getting rid of my desktop, and using my (much better) laptop instead. I'm only wondering if I would be able to hook the two screens I have with it, so I'd end up with three screens. I've seen people doing it to desktops, but am not sure the same could be accomplished with a laptop. My laptop is a sony vaio, and it's got both a VGA output, and an HDMI output. It'd be great is I could simply hook two screens to it, and have three independent screens (not mirrored). on my desktop, I have pretty much the same thing, but with an extra DVI port. I connect the DVI to one screen, and the VGA to an older one. Trying to connect anything to the HDMI simply mirrors whatever is on the DVI (I've tried it a long time ago) So I was wondering if with the laptop I'd be able to do it, and end up with three independent screens. I don't know if there's anything else I could be using instead (i.e. any extra hardware), so recommendations are more than welcome. Thanks in advance, Marcos

  Read the article

• Two screens hooked to one laptop

  - by mplacona

  Hi, I'm thinking of getting rid of my desktop, and using my (much better) laptop instead. I'm only wondering if I would be able to hook the two screens I have with it, so I'd end up with three screens. I've seen people doing it to desktops, but am not sure the same could be accomplished with a laptop. My laptop is a sony vaio, and it's got both a VGA output, and an HDMI output. It'd be great is I could simply hook two screens to it, and have three independent screens (not mirrored). on my desktop, I have pretty much the same thing, but with an extra DVI port. I connect the DVI to one screen, and the VGA to an older one. Trying to connect anything to the HDMI simply mirrors whatever is on the DVI (I've tried it a long time ago) So I was wondering if with the laptop I'd be able to do it, and end up with three independent screens. I don't know if there's anything else I could be using instead (i.e. any extra hardware), so recommendations are more than welcome. Thanks in advance, Marcos

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• Windows 7 using llt for ipv6

  - by Seoman

  The question asked below is based on the specific implementations of the Os not the RFC. Looking on a way to be able to assign a fixed ip address to a host, before it boots I found that Centos 6 works fine with no modifications and Windows 7 does not work at all. As defined in enter link description here exists 3 valid ways of generate a DUID: 1 Link-layer address plus time 2 Vendor-assigned unique ID based on Enterprise Number 3 Link-layer address Looking at the centos, that works fine, I can see the following autogenerated DUID: option dhcp6.client-id 0:1:0:1:19:60:25:f1:52:54:0:6b:b9:9e; and the MAC address for this host is: ifconfig eth1 | grep HWaddr eth1 Link encap:Ethernet HWaddr 52:54:00:6B:B9:9E As you can see, the DUID containts the MAC address. I can assign a fixed ip address to this host by including an entry on my dhcp server similar to: host vm { hardware ethernet 52:54:00:6B:B9:9E; fixed-address6 2001:db8:0:1::200; if packet(0,1) = 1 { log(debug,"VM Request match!"); } } And the Centos 6 gets his ip. On the windows side, I faced a common problem explained on this other link enter link description here As summary, Win7 uses the option 2 of the DUID generation or a variation of this one. On the link explains how to move it to a llt (link layer + time) but is not working fine. If I modify the DUID to one that looks like the one generated on Centos (but with the right MAC) it works as expected. Question 1 How Can I change the DUID generation for Windows 7 to be based on MAC as Centos 6 does? Thanks

  Read the article

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• Automatic o/s reset on a dedicated internet browsing Windows 7 pc.

  - by camelCase

  I have just purchased a new Acer Revo nettop PC for dedicated internet browsing. It will be the only pc on a home network. My original plan was to install one virtual PC for family browsing, another for remote web based server administration and ban browser use from the host Windows 7 o/s. The idea was that I could recover to a fresh VHD image once a week to eliminate any build up of malware inside the browser VMs. However now I am looking for alternative solutions since the Intel Atom cpu does not have hardware VT support which Windows Virtual PC requires. Would it be possible to engineer some type of routine overnight host o/s wipe and recovery? I guess cyber cafes do something like this? The only user data that would need to be retained across a recovery would be browser bookmarks but these could be exported to remote service. Edit 1: I am thinking the o/s reset could be done via some disk image recovery process. Edit 2: Just had a brainwave. Routine browsing could be done via the new Google Chrome O/S. I have just seen a video of the Google Chrome o/s booting off a usb pen drive in seconds.

  Read the article

< Previous Page | 358 359 360 361 362 363 364 365 366 367 368 369  | Next Page >