Search Results

Search found 18364 results on 735 pages for 'nova network'.

Page 365/735 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

  • Cisco Catalyst 3750 connected to Cisco ASA 5505 and dropping packets

    - by Bo102010
    (Cross posted from Super User per suggestion there) At the office, I have inherited a network that I am still trying to fully comprehend. I have a problem today with a new connection between: A port on a Cisco Catalyst 3750 [WS-C3750G-48TS-S running C3750-IPSERVICESK9-M version 12.2(53)SE1] A port on a Cisco ASA 5505 [ASA Software version 8.3(2)] The 3750 is home to a Vlan that has a few ports assigned to it. interface Vlan3 description Internal network (172.18.160.0/24) ip address 172.18.160.1 255.255.255.0 I have a host (outside of my control) that needs to be in this VLAN (i.e it must have an address 172.18.160.something/24) that also needs to access the Internet. To accomplish this, I ran a link from the Catalyst (Gi1/0/13) to the ASA (Ethernet 0/5). I configured the Catalyst port like so: interface GigabitEthernet1/0/13 description To ASA, 172.18.160.69 switchport access vlan 3 switchport mode access speed 100 duplex full I configured the ASA like so: interface Vlan1 nameif inside security-level 100 ip address 172.18.160.69 255.255.255.0 interface Ethernet0/5 speed 100 duplex full Then I plugged the host into Ethernet 0/4 on the ASA and instructed its owner to make its default gateway 172.18.160.69. I made a NAT rule in the ASA and set up some rules, and it's able to access the Internet without issue. However, I noticed that the Catalyst reports a ton of packets being dropped toward the ASA. Catalyst3750#show interfaces GigabitEthernet 1/0/13 | include counters|drops Last clearing of "show interface" counters 00:28:13 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 136909347 This is a huge number of drops, since there's not much traffic on this VLAN at all. I tried these things: Make sure speed and duplex agree on both sides (100 Mbps / Full) Set no cdp enable on the Catalyst Gi10/13 Set no keepalive on the Catalyst Gi10/13 Checked for excessive CPU usage on both Checked for excessive traffic on both Am I missing something? Any help would be appreciated.

    Read the article

  • Split Tunnel VPN using incorrect Tunnel

    - by Brian Schmeltz
    Our company has a handful of field offices that have recently been setup with a regular internet connection after we removed the T1 and router that connected them directly to our network. Now, when the users are in the office, they log in to the VPN to be able to connect to the network. For the sake of them being able to print and scan from the local multi-function we have setup a split tunnel VPN. We currently have about 15-20 users using this setup around the country without any problems. Recently one of our users started having problems accessing internal programs/sites when connecting from both home and the office. There are three other users in the same office and they do not have this problem. I assumed that it was something with the computer and went ahead and replaced it with another of the same model. The computer worked fine in our home office; however, when the user received it, she had the exact same problem both at home and in the field office. Thinking it may be a NIC driver issue I sent her another computer, this time a different model, same problem occurred. If I update the host file to point to the correct paths, things will work, and if I connect via a normal VPN connection everything works, but the user cannot scan or print - which is a problem. Have tried to find ways to create another tunnel on a normal VPN and have tried to find ways to force the correct tunnel on the split tunnel VPN. It appears that there is something related to the ISP because if I connect to Comcast or Verizon it is fine but once she connects to Insite then she has problems. I have been unable to get any support from Insite as they don't feel the issue is with them. We use a Nortel VPN client. Any thoughts or ideas would be appreciated.

    Read the article

  • How to prevent getting infected by rogue security applications

    - by Ieyasu Sawada
    My computer never got infected with a virus before, because I'm using Web of Trust browser plugin, sandboxie and Avast Free antivirus. But today, it got infected with a rogue security application called antivirus.net. I have already removed it using MBAM, SAS, and Kaspersky Virus Removal Tool. And by the way, I was using MSE when my laptop got infected. Seems like the rogue application just killed off the MSE process. And I never even got a warning. I was using the wi-fi from our school, which I think is the cause since most of the computers in our laboratory has rogue applications on it. My question is, how do I prevent this from happening again? It took me about 6 hours to disinfect my computer and I don't want it to happen again. Please enlighten me if these rogue applications really just pop out of nowhere. Note I'm not dumb enough to agree with installing rogue security applications. It just came out of nowhere. I'm happy with MSE, well not after it let antivirus.net penetrate my computer. I've done a little bit of research and it says that it needs the permission of the user to actually install it in the computer: http://www.net-security.org/malware_news.php?id=1245 http://en.wikipedia.org/wiki/Rogue_security_software Is it possible that other computers in our school network have agreed to install those? Or maybe the network admin?

    Read the article

  • Rapidly changing public IP addresses on certain networks?

    - by zenblender
    I run/develop an online game where many of our users are in southeast asia. I recently went to southeast asia and made an alarming discovery. Anywhere I got internet access, whether it was via 3G, a LAN in a hotel, or wifi in a cafe, both in Singapore and the Philippines, I noticed that my IP address was changing CONSTANTLY. I mean the public IP address, not the private one. I could load a page like whatismyip.com and just hit reload and see a new IP address show up every 5-10 seconds! This has lots of consequences for my online game, as many things "break" if the IP address changes for a given user. Basically, I would like to know more about this. Is there a name for the kind of network or router or paradigm that causes this, so I can read up on it? I don't understand WHY a network would function this way. Does it do this on purpose? Is it for security reasons? Is it to anonymize and protect the identity of the users? Or is it just an "old" method that is mostly obsolete in the rest of the world? Thanks for any info that will help me to understand.

    Read the article

  • Drive Mapped On Amazon EC2 Instance Startup Disconnected After Logon

    - by jsn
    I am launching an Amazon EC2 instance (Windows Server 2012), and on startup (though User Data field), it runs this powershell script: <powershell> NET CONFIG SERVER /AUTODISCONNECT:-1 # clear all prior connections net use * /delete /y > C:\delLog.txt 2>&1 # mount new drive net use R: \\dbHost\share /user:username pass /persistent:yes > C:\useLog.txt 2>&1 ipconfig /all > C:\ipLog.txt </powershell> When it launches and I connect to it through RDP, it shows in explorer "Diconnected Network Drive (R:). If I double click it, error message displays "R:\ is not accesible. Access id denied". Normally, it would ask me for credentials to reconnect. I need for this drive to be connected through the duration of the instance. delLog.txt contents: You have these remote connections: T: \\dbHost\share Continuing will cancel the connections. The command completed successfully. useLog.txt contents: The command completed successfully. ipLog.txt contents as expected. The net use commands works fine by itself, it connects. Anyone have any idea what could be wrong? There is only one account on these machines - Administrator. It is a samba share to a Linux server on a private network.

    Read the article

  • Connecting to IPv6 hosts when mobile and on a Surface?

    - by Cerebrate
    Specifically, at my usual location, I have an IPv6 network which connects to the Internet via a static tunnel set up to Hurricane Electric's tunnel broker ( http://www.tunnelbroker.net/ ). This works essentially perfectly, allowing inbound and outbound connectivity. Now, however, I need to connect back to host(s) on that network over IPv6 from mobile tablet(s); meaning the conditions are such that there is no guarantee or even likelihood of native IPv6 support where it happens to be at any given time, and the IPv4 address of the tablet will change on a fairly regular basis. The native Teredo support, as configured by default, functions well enough to let me ping my target hosts, but appears to have neither the reliability nor the throughput to support anything else; I have been unable to make any actual connections (trying a number of TCP-based protocols) using it. I had considered setting up an independent tunnel for the tablet(s), and using scripts to update the client endpoint IP address when it changes, but since both (a) many of the locations will be behind NAT devices over which I have no control, and (b) the option over which I do have control is an AT&T Unite hotspot which does not offer protocol 41 forwarding or respond to ICMP on its public address, this approach does not seem viable. I am additionally constrained as the mobile tablet(s) in question are Surface RTs, and as such are incapable of running, for example, AICCU client software. What is my best option to pursue to obtain IPv6 connectivity in this scenario?

    Read the article

  • Why can a local root turn into any LDAP user?

    - by Daniel Gollás
    I know this has been asked here before, but I am not satisfied with the answers and don't know if it's ok to revive and hijack an older question. We have workstations that authenticate users on an LDAP server. However, the local root user can su into any LDAP user without needing a password. From my perspective this sounds like a huge security problem that I would hope could be avoided at the server level. I can imagine the following scenario where a user can impersonate another and don't know how to prevent it: UserA has limited permissions, but can log into a company workstation using their LDAP password. They can cat /etc/ldap.conf and figure out the LDAP server's address and can ifconfig to check out their own IP address. (This is just an example of how to get the LDAP address, I don't think that is usually a secret and obscurity is not hard to overcome) UserA takes out their own personal laptop, configures authentication and network interfaces to match the company workstation and plugs in the network cable from the workstation to their laptop, boots and logs in as local root (it's his laptop, so he has local root) As root, they su into any other user on LDAP that may or may not have more permissions (without needing a password!), but at the very least, they can impersonate that user without any problem. The other answers on here say that this is normal UNIX behavior, but it sounds really insecure. Can the impersonated user act as that user on an NFS mount for example? (the laptop even has the same IP address). I know they won't be able to act as root on a remote machine, but they can still be any other user they want! There must be a way to prevent this on the LDAP server level right? Or maybe at the NFS server level? Is there some part of the process that I'm missing that actually prevents this? Thanks!!

    Read the article

  • Problems starting autossh on boot [ubuntu]

    - by Ken
    I'm trying to automatically start an SSH tunnel to my server on boot from a ubuntu box. I have an ubuntu box that's mounted on an 18-wheeler and is networked behind an air card. The box hosts a mysql database that i'm trying to have replicated when the aircard is connected. As I can never be sure of my IP and how many or which routers I'm behind I'm connected to my replication server with an SSH tunnel. I got that working using the following command: ssh -R 3307:localhost:3307 [email protected] Now I'd like that to start whenever the box is, and be alive all the time, so I installed auto-ssh and setup this little script: ID=xkenneth HOST=erdosmiller.com AUTOSSH_POLL=15 AUTOSSH_PORT=20000 AUTOSSH_GATETIME=30 AUTOSSH_DEBUG=yes AUTOSSH_PATH=/usr/bin/ssh export AUTOSSH_POLL AUTOSSH_DEBUG AUTOSSH_PATH AUTOSSH_GATETIME AUTOSSH_PORT autossh -2 -fN -M 20000 -R 3307:localhost:3306 ${ID}@${HOST} I've tried putting this scrip in /etc/init.d/ and using a post-up command in /etc/network/interfaces as well as putting it in /etc/network/if-up.d/. In both situations the script starts on boot, but the tunnel doesn't appear to be correctly established. The script works when run manually.

    Read the article

  • Adding 2008 Server to 2008 Domain

    - by Phillip
    Hello, I'm trying to create a lab for testing before I deploy solutions, I'm no experienced IT Administrator, and therefore I come here for help. I'm running 2 Virtual Servers on the same machine on a local connection between those two. They'are able to ping each other. Their names is TSDATA1 and TSDATA2 where TSDATA1 is the Domain Controller. I am able to ping between those two, on both "ping TSDATA1" and "ping 10.0.0.1" which is the IP address of TSDATA1. The IP address of TSDATA2 is 10.0.0.2. I'm trying to join the domain with TSDATA2 both I'm getting this error when trying: Note: This information is intended for a network administrator. If you are not your network's administrator, notify the administrator that you received this information, which has been recorded in the file C:\Windows\debug\dcdiag.txt. The following error occurred when DNS was queried for the service location (SRV) resource record used to locate an Active Directory Domain Controller for domain tsdata.local: The error was: "DNS name does not exist." (error code 0x0000232B RCODE_NAME_ERROR) The query was for the SRV record for _ldap._tcp.dc._msdcs.tsdata.local Common causes of this error include the following: The DNS SRV records required to locate a AD DC for the domain are not registered in DNS. These records are registered with a DNS server automatically when a AD DC is added to a domain. They are updated by the AD DC at set intervals. This computer is configured to use DNS servers with the following IP addresses: 10.0.0.1 One or more of the following zones do not include delegation to its child zone: tsdata.local local . (the root zone) For information about correcting this problem, click Help. I've figured out it has something to do with DNS lookup, but I have no clue what to do. Can anyone help?

    Read the article

  • ProCurve 1800 switch issue

    - by user98651
    I recently deployed ProCurve 1800-24G switches in place of some older ProCurve 2424M switches in my network. However, I'm having a serious problem with the switch connected to the router. It seems, every night when our Windows 2008 R2 server (off site) runs a backup to a iSCSI target (on site) [facilitated through a PPTP tunnel] the LAN loses connectivity with the router. To clarify, there is only one router which is connected to the switch affected by this problem. The only way to resolve the issue is to either reboot the router or pull the ethernet cable that goes to the router and plug it back in. During the outage, clients cannot receive DHCP requests, DNS requests, ping, or do anything else with the router in this state. Now, neither the switch or router are configured extensively and the issue only seems to have surfaced with the new switch in place. I have tried a number of things including replacing cables, rebooting and checking the switch configuration (it is literally as basic as you can get at this point-- flat LAN, no trunking). Interestingly, the router shows (accessed externally) no changes in configuration or status during this state but similarly cannot ping or access other hosts on the network. This issue occurs in different stages of backup (ie, different amounts transferred). I've also dumped packets from the switch into WireShark but cannot seem to find any anomaly yet (I'm looking at packets around the time the issue appeared and at the time when I reset the NIC). Any suggestions for what to look for? Ideas on what could be causing this? I'm seeing some transmit/receive errors on the NIC from both the router and switch side but nothing serious when compared to the total packet counts. I'm seriously doubting hardware at this point, as I have tried another switch, different cables, and a different NIC on the router.

    Read the article

  • VPN Trunk Between Cisco ASA 5520 and DrayTek Vigor 2930

    - by David Heggie
    I'm a bit of a VPN newbie, so please go easy on me ... I'm trying to use the VPN trunking capabilities of the DrayTek Vigor 2930 firewall to bond two IPSec VPN connections to a Cisco ASA 5520 device and I'm getting myself tied in knots and hope someone here with more knowledge / experience can help. I have a remote site with two ADSL connections and the DrayTek box. The main office site has the Cisco ASA device. I am able to setup a single IPSec connection between the two sites on either of the ADSL connections' public IP addresses, but as soon as I try to use the VPN bonding, nothing works. The VPN tunnels are both still up, but the traffic is getting lost somewhere. I suspect it's due to the ASA not knowing how to route the traffic back over the VPN - one minute, traffic from my remote office's network is coming from public ip address #1, the next it's coming from public address #2 and it doesn't know what to do. Well, that's my newbie impression of what's going wrong, but I don't really know: If this is really what's happening If what I'm trying to do (bond two VPN connections from a single remote network to improve the bandwidth / resiliency) is possible with the kit I've got Could anyone help?

    Read the article

  • New AD-DC in a new Site is refusing cross-site IPv4 connections

    - by sysadmin1138
    We just added a new Server 2008 (sp2) Domain Controller in a new Site, our first such config. It's over a VPN gateway WAN (10Mbit). Unfortunately it is displaying a strange network symptom. Connections to the SMB ports (TCP/139 and TCP/445) are being actively refused... if the connection is coming in on pure IPv4. If the incoming connection is coming by way of the 6to4 tunnel those connections establish and work just fine. It isn't the Firewall, since this behavior can be replicated with the firewall turned off. Also, it's actually issuing RST packets to connection attempts; something that only happens with a Windows Firewall if there is a service behind a port and the service itself denies access. I doubt it's some firewall device on the wire, since the server this one replaced was running Samba and access to it from our main network functioned just fine. I'm thinking it might have something to do with the Subnet lists in AD Sites & Services, but I'm not sure. We haven't put any IPv6 addresses in there, just v4, and it's the v4 connections that are being denied. Unfortunately, I can't figure this out. We need to be able to talk to this DC from the main campus. Is there some kind of site-based SMB-level filtering going on? I can talk to the DC's on campus just fine, but that's over that v6 tunnel. I don't have access to a regular machine on that remote subnet, which limits my ability to test.

    Read the article

  • Networking Problem MrxSmb event 50 "Delayed Write Failed" errors occurring all of the sudden

    - by Johnny Musso
    JUST THIS MONTH, we have started getting reports from a number of very stable clients that MrxSmb event id 50 errors keep appearing in their system event logs. Otherwise, they do not appear to have any networking problems except that there is a critical legacy application which seems to either be generating the MrxSmb errors or having errors occur because of them. The legacy application is comprised of 16 bit and 32 bit code and has not been changed or recompiled in many years. It has always been stable on Windows XP systems. The customers that have the problem usually have a small (5 clients or less) peer to peer network with all Windows XP systems. All service packs are loaded on the XP machines. Note: The only thing that seems to correct the problem is disabling opportunistic locking. I don't like this solution because it seems to slow down the network and sometimes causes record locking issues between users (on some networks). Also, this seems to have just started happening - as if a Windows update for XP has caused it? However, I have removed recent updates and it did not correct the issue. Thanks in advance for any help you can provide.

    Read the article

  • Can't resolve offline file conflicts

    - by Bryan
    We use roaming profiles on our Server 2008 R2 domain, with folder redirection for 'desktop', 'my documents' and 'application data'. But as our network is split across two sites, we have one file server at each site, which are configured to use domain based DFS namespaces and DFS replication to keep things in sync. The DFS path for the replication folder is as follows: \\domain\folderredirection$\<username>\<redirected-folder-name> The real paths are \\site-1-server\folderredirection$\<username>\<redirected-folder-name> and \\site-2-server\folderredirection$\<username>\<redirected-folder-name> As our users all switch between sites (sometimes several time per day), our folder redirection policy has to redirect to the DFS roots rather than hardcoded to a specific server. Both DFS and DFS-R have been proven to be working perfectly. On our laptops, we use offline files for the redirected folders, and this also works fine, however the problem is as follows: When conflicts occur in offline files, it is impossible to resolve the conflicts. I'm given the usual conflict resolution options (i.e. 'Ignore', 'Keep Both', 'Keep network' and 'Keep local'), however, not one of these options will resolve any conflict, yet no error is produced. We only use offline files on laptops, which have either Windows XP Professional or Windows 7 Professional installed. The problem is not specific to any one laptop, it affects every laptop and every conflicting file in exactly the same way. I would have thought the set up we have is common for companies that have multiple sites, so I'm hoping someone will have seen this before?

    Read the article

  • Resource Monitor (resmon) in Windows Server 2008 R2

    - by Clever Human
    In Windows Server 2008 R2's Resource Monitor, is there a way to set the scale of the various graphs to be constant values instead of variable based on data? It seems to me that the utility of a graph is to get a quick overview glance at the values those graphs are showing. So if I look at the CPU graph and the line is up near the top, I can know immediately that something is using all my CPU and go investigate what. I don't really care if the CPU is jumping between .01% and 2%. Or if the network usage monitor is up near the top, I will know that all my bandwidth is being used up, and go figure out what. But the way things are now, the graphs are meaningless because the scales constantly shift. If you look at the network usage graph in one second it might have a scale out of 100kbps, and the next second have a scale based on 1mbps! So... is there a registry key or something that will peg the scale of these graphs to logical maximums? (the graph on the right hand side of the screenshot below):

    Read the article

  • Windows 7 hangs while loading desktop

    - by Joshua
    I am facing a weird problem. My computer hangs while loading the desktop, and only the background shows up; no icons or bars load. If I power the system on and off about 4-6 times, I may be able to use it normally. The desktop loads normally after rebooting or in safe mode; this only occurs when I start the system normally. I've tried several things to fix it, such as removing all start-up items, but it still doesn't solve the problem. What should I do? I found three major errors in Event Viewer: Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Microsoft-Windows-DistributedCOM Level: Error DCOM got error "1084" attempting to start the service WSearch with arguments "" in order to run the server: {7D096C5F-AC08-4F1F-BEB7-5C22C517CE39} Source: Service Control Manager Level: Error The Network List Service service depends on the Network Location Awareness service which failed to start because of the following error: The dependency service or group failed to start.

    Read the article

  • How can I manage AWS VPC ssh access accounts and keys across multiple instances?

    - by deitch
    I am setting up a standard AWS VPC structure: a public subnet some private subnets, hosts on each, ELB, etc. Operational network access will be via either an ssh bastion host or an openvpn instance. Once on the network (bastion or openvpn), admins use ssh to access the individual instances. From what I can tell all of the docs seem to depend on a single user with sudo rights and a single public ssh key. But is that really best practice? Isn't it much better to have each user access each host under their own name? So I can deploy accounts and ssh public keys to each server, but that rapidly gets unmanageable. How do people recommend managing user accounts? I've looked at: IAM: It doesn't like like IAM has a method for automatically distributing accounts and ssh keys to VPC instances. IAM via LDAP: IAM doesn't have an LDAP API LDAP: set up my own LDAP servers (redundant, of course). Bit of a pain to manage, still better than managing on every host, especially as we grow. Shared ssh key: rely on the VPN/bastion to track user activities. I don't love it, but... What do people recommend? NOTE: I moved this over from accidentally posting in StackOverflow.

    Read the article

  • Why do I have 55 local area connections in ipconfig?

    - by RMorrisey
    Windows Vista Home Premium. I should mention that I am having no problem whatever getting an internet connection. When I type "ipconfig" in the console, I get (55!) messages of 3 lines each, listing a ton of disconnected network connections. My PC only has one network card. Each message looks like this: Tunnel adapter Local Area Connection* 55: Media State . . . . . . . . . . . : Media disconnected Connection-specific DNS Suffix . : These don't cause a major problem; they make it a pain, though, to fish upward and find my IP address. How can I get rid of them? Edit: Actually, a few connection numbers are randomly missing from the sequence; so, it's really more like 30 or 40 connection messages, rather than all 55. Not sure why that is, either.

    Read the article

  • eee box "drobpox" server 24/7

    - by microspino
    I'd like to create a mini dropbox and print server on a small soho network of 5 users (all of them use windows XP desktops). The device need to run 24/7 or at least 12/7 (I can accept just workday hours too but the other two options would be better). Dropbox mini server: I mean I will have a 90gb dropbox on every computer on my network LAN syncing with It and the one onto It syncing to the web. Print Server: I have a Samsung A4 small laser printer, a HP500 Designjet Plotter, a Samsung Multifunction Machine (fax/print/scan/copy), a modern HP color A3 Deskjet printer and a HP laserjet A4 color printer. All of them need to be connected to this mini server. Fax/Scan server: since I have the above mentioned fax/print/scan/copy machine I would like to make people use It from/to their computers through the mini server. I thought to a recent EEEBOX machine because I heard good things about ATOM cpus and because It seems that a recent BIOS version could switch It off and on autonomously. I'd like to listen some advice from You. Best of all would be: - If You have something similar running for a long time - If You disagree with this hardware choice and If You would suggest some other device. - If You see any issues with my printing setup - Anything else ;) My budget is from Zero (using right sw to build something on top on a old PC) to 500€ max.

    Read the article

  • iptables: allowing incoming for 192.168.1.0/24 allowed incoming for all?

    - by nortally
    The internal side of my ISP router has three devices: ISP router 128.128.43.1 Firewall router 128.128.43.2 Server 128.128.43.3 Behind the Firewall router is a NAT network using 192.168.100.n/24 This question is regarding iptables running on the Server. I wanted to allow access to port 8080 only from the NAT clients behind the Firewall router, so I used this rule -A Firewall-1-INPUT -s 192.168.100.0/24 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPT This worked, but UNEXPECTEDLY ALLOWED GLOBAL ACCESS, which resulted in our JBOSS server getting compromised. I now know that the correct rule is to use the Firewall router's address instead of the internal network, but can anyone explain why the first rule allowed global access? I would have expected it to just fail. Full config, mostly lifted from a RedHat server: *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :Firewall-1-INPUT - [0:0] -A INPUT -j Firewall-1-INPUT -A FORWARD -j Firewall-1-INPUT -A Firewall-1-INPUT -i lo -j ACCEPT -A Firewall-1-INPUT -p icmp --icmp-type any -j ACCEPT -A Firewall-1-INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow ssh from all" -A Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 22 -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow https from all" -A Firewall-1-INPUT -m state --state NEW -m tcp -p tcp --dport 443 -j ACCEPT -A Firewall-1-INPUT -m comment --comment "allow JBOSS from Firewall" ### THIS RESULTED IN GLOBAL ACCESS TO PORT 8080 ### -A Firewall-1-INPUT -s 192.168.100.0/24 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPT ### THIS WORKED -A Firewall-1-INPUT -s 128.128.43.2 -m state --state NEW -m tcp -p tcp --dport 8080 -j ACCEPt ### -A Firewall-1-INPUT -j REJECT --reject-with icmp-host-prohibited COMMIT

    Read the article

  • Setup for a live (low-latency) audio video broadcast over Wi-Fi?

    - by Majal Mirasol
    The Upgrade We are capturing audio (from mixer) and video (from a camera) from a main auditorium and passing it to separate rooms within the building. We used to have done this via manual audio/video cables and wires. We wanted to "upgrade" the system and wirelessly broadcast the stream via Wi-Fi. The Problem In our current setup (Wirecast running on A10 on a Wireless-N network), we have the problem of delay. Our streams are delayed from a minute up to five minutes on the clients (laptop/iPad/Android). This had not been a problem from the previous wired connections. Since the wireless network is local, we thought that a delay of less than a second should be achievable. Our Question And so it goes. Anybody there who has any experience for a setup that has both low latency and at the same time user-friendly to clients streaming in the program? Any recommendations would be highly appreciated. (Our current setup in on Windows 7, but setup on a dedicated Linux box is preferred, if achievable.)

    Read the article

  • Compiling Gearman PHP Library for CentOS 5.8

    - by Andrew Ellis
    I've been trying to get Gearman compiled on CentOS 5.8 all afternoon. Unfortunately I am restricted to this version of CentOS by my CTO and how he has our entire network configured. I think it's simply because we don't have enough resources to upgrade our network... But anyways, the problem at hand. I have searched through Server Fault, Stack Overflow, Google, and am unable to locate a working solution. What I have below is stuff I have pieced together from my searching. Searches have told said to install the following via yum: yum -y install --enablerepo=remi boost141-devel libgearman-devel e2fsprogs-devel e2fsprogs gcc44 gcc-c++ To get the Boost headers working correctly I did this: cp -f /usr/lib/boost141/* /usr/lib/ cp -f /usr/lib64/boost141/* /usr/lib64/ rm -f /usr/include/boost ln -s /usr/include/boost141/boost /usr/include/boost With all of the dependancies installed and paths setup I then download and compile gearmand-1.1.2 just fine. wget -O /tmp/gearmand-1.1.2.tar.gz https://launchpad.net/gearmand/1.2/1.1.2/+download/gearmand-1.1.2.tar.gz cd /tmp && tar zxvf gearmand-1.1.2.tar.gz ./configure && make -j8 && make install That works correctly. So now I need to install the Gearman library for PHP. I have attempted through PECL and downloading the source directly, both result in the same error: checking whether to enable gearman support... yes, shared not found configure: error: Please install libgearman What I don't understand is I installed the libgearman-devel package which also installed the core libgearman. The installation installs libgearman-devel-0.14-3.el5.x86_64, libgearman-devel-0.14-3.el5.i386, libgearman-0.14-3.el5.x86_64, and libgearman-0.14-3.el5.i386. Is it possible the package version is lower than what is required? I'm still poking around with this, but figured I'd throw this up to see if anyone has a solution while I continue to research a fix. Thanks!

    Read the article

  • Java Swing over Remote Desktop - Strange, weird GUI squashing

    - by ADTC
    I thought this question fits SuperUser more than StackOverflow because it's not about actual Java programming, though programmers might be more likely to encounter the problem. Anyway, let me start of with some stats before I ask the actual question: Laptop: Windows 7 x32 Screen resolution 1024 x 768; Nvidia GeForce Go 6200 Connected to desktop via ad-hoc wireless network Access internet via desktop Desktop: Windows 7 x64 Screen resolution 1920 x 1080 Connected to laptop via ad-hoc wireless network Access internet via cable modem I'm connecting to my laptop via Remote Desktop from my desktop to take advantage of the large screen. I'm doing programming on my laptop (for portability reasons). Everything else runs smooth and fast over Remote Desktop as both computers are connected directly over the ad-hoc wireless. The only problem is this: Java Swing apps don't display the GUI properly. I acquired a Java Swing application and I'm debugging it in Eclipse. Here's what I got when I ran the app: Apparently there doesn't seem to be anything wrong with the GUI application I'm debugging, because the Java Control Panel exhibits the same problem. I've searched high and low in Google about this; the closest I came to a solution is this. But sadly, the use of -Dsun.java2d.nodraw=true has no effect at all. This only happens over Remote Desktop. I have tried locally and the GUI apps display properly. This isn't a dealbreaker for me as I can stop using Remote Desktop when developing Java Swing apps. However, I would like to know if anyone has encountered this and found any solution. PS: All software involved (Eclipse, Java JRE, etc.) are latest versions.

    Read the article

  • How to set up multiple DNS servers on an intranet

    - by Brent
    We have an Active Directory network, with a mixture of Windows DNS, linux BIND servers, and want to use OpenDNS as our external DNS provider. I am wondering What is the best way to set up these servers (regarding forwarders, recursion, etc.)? Active Directory is our main internal DNS for our domain, and has 3 redundant servers. DHCP and all our servers use these as their DNS servers. Then we have a legacy AD server from an old network that is still authoritative for a bunch of domains. Finally, we have a couple of Linux Bind servers that are authoritative for a bunch of websites we host. Should our main AD servers point to our legacy AD server, which points to one of our BIND servers, which points to the other BIND server, which finally points out to openDNS? Or should our main AD servers point to all of these directly? - or is there a better option? What happens if a domain is listed in 2 places? Does DNS process the forwarders in order? What about root servers - if I want to use OpenDNS for "everything else", do I just list them as the last forwarders, and delete the root servers from all my DNS servers? How does recursion work - in this scenario, should I be using recursion or not?

    Read the article

  • IIS6 intranet site using integrated authentication fails to load when accessed externally

    - by maik
    I've developed a couple of internal sites for my organization that use integrated authentication. Ultimately we want these sites to be accessible externally to users with domain-joined computers. The sites work as expected on domain computers while on the internal network. The problem comes when I take my laptop home and try to access those sites. IIS only has integrated authentication enabled for the two sites. When I browse to the site using IE8 I get a username/password prompt asking for domain credentials. I can put those in and it will work, but the goal is to use the cached token for integrated authentication. Next I reasoned that IE wouldn't response to an integrated auth request (is NTLM the right term for this?) unless the site was trusted. I tried adding the site to Trusted Sites but I get the same behavior as the before. I then added the site to Local Intranet sites and that is where things get weird. I get a generic error page from IE, no error code or anything. Just for funsies I loaded up Firefox (which I had previously set up to use integrated authentication) and I added this new site to network.automatic-ntlm-auth.trusted-uris. Much to my surprise I was able to load the pages up with no problem at all and saw exactly what I was expecting (including verification that the integrated authentication worked). My mind is a bit boggled at the moment as I'm not really sure where to go from here. I was hoping some of you may be able to provide some insight.

    Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >