Search Results

Search found 21072 results on 843 pages for 'thin client'.

Page 365/843 | < Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >

• Problem with PXE boot

  - by user70523

  I followed the following link for PXE boot, http://www.howtoforge.com/setting-up-a-pxe-install-server-on-ubuntu-9.10-p3 and I was able to ping the client from the server and also when I booted up the client It is getting the IP address from the server. But later,I got this error PXELinux 3.82 2009-06-09 . . . [other informations] !PXE Entry point found (we hope) at 9D3B:0109 via plan A UNDI code segment at 9D3B len 16C2 UNDI data segment at 933B len A000 Getting cached packet 01 02 03 . . . [other informations] TFTP prefix: Trying to load: pxelinux.cfg/ec5db4c0-74fe-d511-b9e7-3d9235afe5a1 Trying to load: pxelinux.cfg/01-00-17-31-b6-5e-a8 Trying to load: pxelinux.cfg/0A64491E Trying to load: pxelinux.cfg/0A64491 Trying to load: pxelinux.cfg/0A6449 Trying to load: pxelinux.cfg/0A644 Trying to load: pxelinux.cfg/0A64 Trying to load: pxelinux.cfg/0A6 Trying to load: pxelinux.cfg/0A Trying to load: pxelinux.cfg/0 Trying to load: pxelinux.cfg/default Unable to locate configuration file Boot failed: press a key to retry or wait for reset I have put all the files mentioned in the link in tftpboot. Can anyone explain what could be the problem. Thanks in advance

  Read the article

• ESXi Guests will not boot on IBM x3550 M3

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. VM Host Server: IBM x3550 M3 7944AC1 server w/ 2x Intel Xeon E5607 2.27Ghz CPUs ESXi 5.0.0 Build 623860, built for IBM Hardware downloaded from IBM Storage: 2x500GB SAS local storage 8GB RAM Vt is verified to be ENABLED Server Health Status: Normal The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspucious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space.

  Read the article

• How to set up a VPN Incoming connection with Windows to tunnel Internet traffic?

  - by Mehrdad

  I want to set up a VPN on a remote server to route all my Internet traffic for privacy reasons. I can set up an incoming connection and connect to it successfully. The problem is, I can just see the remote computer and no other Web sites will open. I want the remote server to act like a NAT. How can I do that? Note that I don't want to split Internet traffic. I actually want to send all the traffic to the remote server but need to make it relay the traffic. For the record, my remote server is Windows Web Server 2008 which does not have routing and remote access service. Clarification I'm mostly interested in server configuration. I don't have any problems configuring the client. By the way, Windows Web Server 2008 seems to have the same VPN features built in client OSes (like Vista) and specifically, it doesn't include the RRAS console in MMC. I'm also open to suggestions regarding third party PPTP/L2TP daemons available, if they are free.

  Read the article

• How to connect to Oracle DB via ODBC

  - by Mat

  I am attempting to connect to a remote Oracle DB via ODBC. I am totally inexperienced and fail to connect. What I have installed: Oracle 'ODBC Driver for RDB' A program I want to connect from (Altova Mapforce, an ETL) What I do: Under Administrative tools I open the Windows "ODBC Data Source Administrator I click 'Add..' and select the Oracle ODBC Driver The Window 'Oracle RDB Driver Setup' opens. I fill in: Data source name: free choice Description: I leave blank Transport: I choose TCP/IP Server: I input the IP address of the server Service: I leave 'generic' UserID: I enter the user name (that belongs to the password I have) Attach Statement: no idea what do do here?? Upon choosing 'OK', the 'Oracle RDB ODBC Driver Connect' opens and I am prompted the password. I enter the password and the connection fails. Questions Do I need further programs on my computer, e.g. the Oracle client of Instant client? I am never prompted the port of the server - isn't this relevant? I am never prompted SID - isn't this relevant? I connected from SQL developer easily - it prompted only server IP, port, username, password and SID.

  Read the article

• Running multiple sites on a LAMP with secure isolation

  - by David C.

  Hi everybody, I have been administering a few LAMP servers with 2-5 sites on each of them. These are basically owned by the same user/client so there are no security issues except from attacks through vulnerable deamons or scripts. I am builing my own server and would like to start hosting multiple sites. My first concern is... ISOLATION. How can I avoid that a c99 script could deface all the virtual hosts? Also, should I prevent that c99 to be able to write/read the other sites' directories? (It is easy to "cat" a config.php from another site and then get into the mysql database) My server is a VPS with 512M burstable to 1G. Among the free hosting managers, is there any small one which works for my VPS? (which maybe is compatible with the security approach I would like to have) Currently I am not planning to host over 10 sites but I would not accept that a client/hacker could navigate into unwanted directories or, worse, run malicious scripts. FTP management would be fine. I don't want to complicate things with SSH isolation. What is the best practice in this case? Basically, what do hosting companies do to sleep well? :) Thanks very much! David

  Read the article

• LDAP authentication issue with Kerio Connect

  - by djk

  Hi, We have Kerio Connect (mail server) running on a Windows Server 2003 server on a domain. In the webmail client, users are able to change their domain password. This functionality used to work fine until a user tried to change their password a few days ago, when every password they'd try would result in the webmail client claiming their password was "invalid". I spoke to Kerio about this and they claim that this error is returned by the domain controller, which supports my initial investigations. The error that the DC is logging when an attempt is made to change the password is this: "80090308: LdapErr: DSID-0C090334, comment: AcceptSecurityContext error, data 52e, vece" The "data 52e" part indicates that this is an "invalid credentials" error. I don't see how this can be as I've tried (in the Kerio Connect configuration) various accounts that have privileges to modify accounts, including my own as I am a domain admin. I have ran 'dcdiag' (all tests) on the DC and it came back passing every single one of them. I've searched high and low for an answer to this and came up empty. Does anyone have any idea why this may have suddenly started happening? Thanks! Edit: I should mention that the passwords we are changing to do comply with the complexity policy.

  Read the article

• Adobe Acrobat Reader don't zoom out the page enough in "one page" mode

  - by mbaitoff

  I'm using Adobe Acrobat Reader version 9.4 under Debian Lenny. I'm experiencing a problem: when I push the "Show one page at a time" button, I expect the page to zoom such that pressing PgUp/PgDn would turn to the next/previous page. However, the zoom seems to be not enough - very thin bottom portion of the page doesn't fit inside the reader window, and pressing PgUp/PgDn gives the jitter of the same page, and I have to push twice to get to the next page. It is even worse in continuous page mode - a roll of pages begin to be non-synced with window boundaries, ending up with page break right in the middle of the view after several turns of the pages. This behaviour doesn't occur on windows version - I have a page properly zoomed in single/continuous modes, so that turning the pages is performed as page-at-once, as intended. How to make the Acrobat Reader fit the page to window properly? Thats how it looks before pressing PgDn (notice the bottom edge of the "paper" hidden beneath the bottom window edge): Thats how it looks after pressing PgDn (notice the "paper" bottom edge emerged from beneath the window edge, while the "paper" upper edge hides behind the upper window edge, showing that the document window size is not enough to contain the whole page):

  Read the article

• Bluehost Emails Getting Blocked

  - by colithium

  A site for my client has the run-of-the-mill "website with users" email pattern. Create an account, get an activation email. Get an email when a subscription is expiring, etc. The site is hosted on Bluehost and currently it uses php's mail() function. There isn't much configuration that is allowed (as far as I know). The trouble is, about a third of these emails disappear into the void. They aren't in spam or junk folders, there's no bounce message, they just cease to exist. I've read about Bluehost email troubles but I can't figure out what my options are for fixing it. These aren't marketing emails, ie they have user-specific information contained within them. I suppose if a solution offers a good templating system that would be fine. What are my options? Excerpt of headers when delivered to a Gmail address: Received-SPF: neutral (google.com: 00.000.000.000 is neither permitted nor denied by best guess record for domain of domain@box###.bluehost.com) client-ip=00.000.000.000; DomainKey-Status: good Authentication-Results: mx.google.com; spf=neutral (google.com: 00.000.000.000 is neither permitted nor denied by best guess record for domain of domain@box###.bluehost.com) smtp.mail=domain@box###.bluehost.com; domainkeys=pass [email protected]

  Read the article

• SSH traffic over openvpn connection freezes when I cat a file

  - by user42055

  I have an openvpn (version 2.1_rc15 at both ends) connection setup between two gentoo boxes using shared keys. it works fine for the most part. I use mysql, http, ftp, scp over the vpn with no problems. But when I ssh from the client to the server over the vpn, weird things happen. I can login, i can execute some commands. But if i try to run an ncurses application like top, or i try to cat a file, the connection will stall and I'll have to sever the ssh session. I can, for example, execute "echo blah; echo .; echo blah" and it will output the three lines of text over the ssh session fine. But if i execute "cat /etc/motd" the session will freeze the moment I press enter. I compiled openvpn 2.1.1 on my mac and copied over my config directory from my gentoo client. The mac connected and ssh sessions worked fine without freezing. I then compiled it on my older gentoo box (2.6.26 kernel) which I am retiring due to a dying hard drive, and ssh over it also works perfectly. Why does it fail on my brand new gentoo box ? I've tried compiling three different kernels in case it was that, but other than that there should be no difference between my older and my newer gentoo boxes that I can think of. Any suggestions on what's wrong ?

  Read the article

• CentOS centralised logging, syslogd, rsyslog, syslog-ng, logstash sender?

  - by benbradley

  I'm trying to figure out the best way to setup a central place to store and interrogate server logs. syslog, Apache, MySQL etc. I've found a few different options but I'm not sure what would be best. I'm looking for something that is easy to install and keep updated on many virtual machines. I can add it to a VM template going forward but I'd also like it to be easy to install to keep the VM complexity down. The options I've found so far are: syslogd syslog-ng rsyslog syslogd/syslog-ng/rsyslog to logstash/ElasticSearch logstash agent in each log "client" to send to Redis/logstash/ElasticSearch And all sorts of permutations of the above. What's the most resilient and light from the log "client" perspective? I'd like to avoid the situation where log "clients" hang because they are unable to send their logs to the logging server. Also I would still like to keep local logging and the rotation/retention provided by logrotate in place. Any ideas/suggestions or reasons for or against any of the above? Or suggestions of a different structure entirely? Cheers, B

  Read the article

• How do I hook into Tar with BASH?

  - by orb

  Long Story Short I am working with Tar archives that contain PNG images in base64 encoding. I would like to use BASH (or whatever else works) to hook into the extraction function of Tar to decode PNG images from base64 encoding to standard PNG encoding after the files are unpacked. A simple cat $input-file | base64 -d >$output-file will successfully decode the images. Is there a way I can hook into tar -xf so that users do not have to do any (or minimal) extra work to decode the images? In the GNU Tar documentation (http://www.gnu.org/software/tar/manual/html_chapter/Backups.html#SEC97) I found that there are in fact variables reserved to hold the names of functions I desire to be hooked into various moments in Tar program execution. However, the documentation explains that these variables, along with other variables that can be set to configure Tar, are located in a file named backup-specs. Unfortunately, the path to this file is not given. Further, running sudo find / -name backup-specs tells me that this file is not present on my Ubuntu version 13.04 system. Background Information not included in the Long Story Short I have been working on a browser-based (WebGL) particle effect creation application (http://www.particleeffect.org), (https://github.com/cgrabowski/webgl-particle-effect-editor), (https://github.com/cgrabowski/webgl-particle-effect). I have began to write a client-side-only solution for saving and loading effect data as a tar archive. However, since client-side JavaScript has limited capability to process binary data, the images used as textures in the effect are saved with base64 encoding. I have been able to implement saving effect data as a Tar archive (haven't pushed that to Github yet). However, the images present in said Tar archive cannot be manipulated unless they are decoded from base64 encoding.

  Read the article

• Problem setting up HP PhotoSmart C4783

  - by ProfKaos

  I am trying to get several PC's on a network to connect to my client's new wireless printer, the C4783. I initially installed the whole HP 'tsumami of software' the comes with the printer onto my laptop, connected to the printer over USB, and corrected it's networking config. My laptop now also can connect to and print on the printer over the wireless network, as is intended for all PC's. However, when I try and install the HP software on my client's netbook, the HP software cannot find the printer. Firewall was turned off during this time, so doesn't play a role. I tried re-installing all software, but I initially only got a "Repair" or "Uninstall". Choosing Uninstall triggers a lengthy process that ends with a sudden and forceful restart, after which the same "Repair" or "Uninstall" choices are present. Looks like uninstall doesn't. Any suggestions as to how I can begin diagnosing why my laptop has no problem connecting to the printer, but two others do? Wireless is unsecured, and no, nobody has to know where I am right now. :-)

  Read the article

• Using mod_rewrite to mask /cgi-bin/abc as /def

  - by Alois Mahdal

  I have a seemingly easy task, but somehow I just can't get it to work: Some interesting lines from my httpd.conf: ... DocumentRoot "D:/opt/apache/htdocs" ... ScriptAlias /cgi-bin/ "D:/opt/apache/cgi-bin/" ... <Directory "D:/opt/apache/htdocs"> Options Indexes FollowSymLinks ExecCGI AllowOverride None Order allow,deny Allow from all </Directory> <Directory "D:/opt/apache/cgi-bin/"> AllowOverride None Options ExecCGI Order allow,deny Allow from all </Directory> (I know it's dumb but it's only a testing machine :D.) Now, I have d:\opt\apache\cgi-bin\expired.pl and I expect GET /licensecheck.php?code=123456. And I wish to fake client into thinking it speaks with /licensecheck.php, but actually return data by \expired.pl. What I tried was setting following at the end of http.conf: RewriteEngine on RewriteRule ^/licensecheck.php$ /cgi-bin/expired.pl [T=application/x-httpd-cgi,L] ...but it keeps 404-ing me, looking for cgi-bin directory (not cgi-bin\expired.pl) in my DocumentRoot! [error] [client 127.0.0.1] script not found or unable to stat: D:/opt/apache/htdocs/cgi-bin /cgi-bin/expired.pl and all other scripts in /cgi-bin/ work as expected, Only way I could make it work was actually putting the \expired.pl to DocumentRoot, but I don't want this, I want my cgi-bin neatly separated :)

  Read the article

• How to use the correct SSH private key?

  - by Dail

  I have a private key inside /home/myuser/.ssh/privateKey I have a problem connecting to the ssh server, because i always get: Permission denied (publickey). I tried to debug the problem and i find that ssh is reading wrong file, take a look at the output: [damiano@Damiano-PC .ssh]$ ssh -v root@vps1 OpenSSH_5.8p2, OpenSSL 1.0.0g-fips 18 Jan 2012 debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for vps1 debug1: Applying options for * debug1: Connecting to 111.111.111.111 [111.111.111.111] port 2000. debug1: Connection established. debug1: identity file /home/damiano/.ssh/id_rsa type -1 debug1: identity file /home/damiano/.ssh/id_rsa-cert type -1 debug1: identity file /home/damiano/.ssh/id_dsa type -1 debug1: identity file /home/damiano/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.8p1 Debian-7ubuntu1 debug1: match: OpenSSH_5.8p1 Debian-7ubuntu1 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.8 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Server host key: RSA 74:8f:87:fe:b8:25:85:02:d4:b6:5e:03:08:d0:9f:4e debug1: Host '[111.111.111.111]:2000' is known and matches the RSA host key. debug1: Found key in /home/damiano/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /home/damiano/.ssh/id_rsa debug1: Trying private key: /home/damiano/.ssh/id_dsa debug1: No more authentication methods to try. as you can see ssh is trying to read: /home/damiano/.ssh/id_rsa but i don't have this file, i named it differently. How could I tell to SSH to use the correct private key file? Thanks!

  Read the article

• I have added a port to the public zone in firewalld but still can't access the port

  - by mikemaccana

  I've been using iptables for a long time, but have never used firewalld until recently. I have enabled port 3000 TCP via firewalld with the following command: # firewall-cmd --zone=public --add-port=3000/tcp --permanent However I can't access the server on port 3000. From an external box: telnet 178.62.16.244 3000 Trying 178.62.16.244... telnet: connect to address 178.62.16.244: Connection refused There are no routing issues: I have a separate rule for a port forward from port 80 to port 8000 which works fine externally. My app is definitely listening on the port too: Proto Recv-Q Send-Q Local Address Foreign Address State User Inode PID/Program name tcp 0 0 0.0.0.0:3000 0.0.0.0:* LISTEN 99 36797 18662/node firewall-cmd doesn't seem to show the port either - see how ports is empty. You can see the forward rule I mentioned earlier. # firewall-cmd --list-all public (default, active) interfaces: eth0 sources: services: dhcpv6-client ssh ports: masquerade: no forward-ports: port=80:proto=tcp:toport=8000:toaddr= icmp-blocks: rich rules: However I can see the rule in the XML config file: # cat /etc/firewalld/zones/public.xml <?xml version="1.0" encoding="utf-8"?> <zone> <short>Public</short> <description>For use in public areas. You do not trust the other computers on networks to not harm your computer. Only selected incoming connections are accepted.</description> <service name="dhcpv6-client"/> <service name="ssh"/> <port protocol="tcp" port="3000"/> <forward-port to-port="8000" protocol="tcp" port="80"/> </zone> What else do I need to do to allow access to my app on port 3000? Also: is adding access via a port the correct thing to do? Or should I make a firewalld 'service' for my app instead?

  Read the article

• Why won't dhclient use the static IP I'm telling it to request?

  - by mike

  Here's my /etc/dhcp3/dhclient.conf: request subnet-mask, broadcast-address, time-offset, routers, domain-name, domain-name-servers, domain-search, host-name, netbios-name-servers, netbios-scope, interface-mtu; timeout 60; reject 192.168.1.27; alias { interface "eth0"; fixed-address 192.168.1.222; } lease { interface "eth0"; fixed-address 192.168.1.222; option subnet-mask 255.255.255.0; option broadcast-address 255.255.255.255; option routers 192.168.1.254; option domain-name-servers 192.168.1.254; } When I run "dhclient eth0", I get this: There is already a pid file /var/run/dhclient.pid with pid 6511 killed old client process, removed PID file Internet Systems Consortium DHCP Client V3.1.1 Copyright 2004-2008 Internet Systems Consortium. All rights reserved. For info, please visit http://www.isc.org/sw/dhcp/ wmaster0: unknown hardware address type 801 wmaster0: unknown hardware address type 801 Listening on LPF/eth0/00:1c:25:97:82:20 Sending on LPF/eth0/00:1c:25:97:82:20 Sending on Socket/fallback DHCPREQUEST of 192.168.1.27 on eth0 to 255.255.255.255 port 67 DHCPACK of 192.168.1.27 from 192.168.1.254 bound to 192.168.1.27 -- renewal in 1468 seconds. I used strace to make sure that dhclient really is reading that conf file. Why isn't it paying attention to my "reject 192.168.1.27" and "fixed-address 192.168.1.222" lines?

  Read the article

• memcache fast-cgi php apache 2.2 windows 7 creating problems

  - by Ahmad

  hi, i am trying to run memcache, fast-cgi with apache 2.2 + php on a windows 7 machine. if i dont use memcache everything works fine. the moment i disable extension=php_memcache.dll in php.ini everything returns to normal. once i start apache, the apache logs say: [Wed Jan 12 18:19:23 2011] [notice] Apache/2.2.17 (Win32) mod_fcgid/2.3.6 configured -- resuming normal operations [Wed Jan 12 18:19:23 2011] [notice] Server built: Oct 18 2010 01:58:12 [Wed Jan 12 18:19:23 2011] [notice] Parent: Created child process 412 [Wed Jan 12 18:19:23 2011] [notice] Child 412: Child process is running [Wed Jan 12 18:19:23 2011] [notice] Child 412: Acquired the start mutex. [Wed Jan 12 18:19:23 2011] [notice] Child 412: Starting 64 worker threads. [Wed Jan 12 18:19:23 2011] [notice] Child 412: Starting thread to listen on port 80. and after accessing the page [the page just has echo phpinfo()]. i get this error in the error.log [Wed Jan 12 18:20:54 2011] [warn] [client 127.0.0.1] (OS 109)The pipe has been ended. : mod_fcgid: get overlap result error [Wed Jan 12 18:20:54 2011] [error] [client 127.0.0.1] Premature end of script headers: index.php i have php_memcache.dll in my ext directory and httpd.conf is like this: LoadModule fcgid_module modules/mod_fcgid.so FcgidInitialEnv PHPRC "c:/php" FcgidInitialEnv PATH "c:/php;C:/WINDOWS/system32;C:/WINDOWS;C:/WINDOWS/System32/Wbem;" FcgidInitialEnv SystemRoot "C:/Windows" FcgidInitialEnv SystemDrive "C:" FcgidInitialEnv TEMP "C:/WINDOWS/Temp" FcgidInitialEnv TMP "C:/WINDOWS/Temp" FcgidInitialEnv windir "C:/WINDOWS" FcgidIOTimeout 64 FcgidConnectTimeout 32 FcgidMaxRequestsPerProcess 500 <Files ~ "\.php$>" AddHandler fcgid-script .php FcgidWrapper "c:/php/php-cgi.exe" .php </Files> so the problem has to be related to memcache coz if i disable it, fast-cgi seems to be working fine. any possible reasons for this?? the memcache service is running.. i can check it through control panel-services

  Read the article

• Web based file search in the lan?

  - by Magnetic_dud

  I would like to search files in my lan easily. (over 500k files on SMB shares, it would take ages with other ways) I mean, i just need to do a quick search on file names, i don't care content indexing at all, as most of my files are in a proprietary format, and the file name is explicative enough. But, date range filters are a must for me. I just need a quick search like voidtools' everything can do, but in a network way The files are on a WHS box (lol, Videos and Music share names are not appropriate for a company, but a license for that win2003-based os is cheaper than an xp home one!) I tried: Lansearch pro: it is not good for me, as i need a quick index Network Search Engine: it would be perfect, but does not offer a date range filter Microsoft Search Server 2008 Express, but it is horrible! First, does NOT index filenames, and then, my Core2Duo is not powerful enough to run it smoothly. Google Desktop with a proxy on localhost to make it run on the lan, but i don't like the hacked result. The preinstalled Windows Search 4.0 but it sucks totally in choosing the relevance of data - uninstalled Docco... what's that? I am considering to try: Ibm omnifind DocFetcher (can it work as a client? did not investigated yet) Strigi (it looks like that it can work as a client, right?) Any ideas/suggestions?

  Read the article

• emails not sending from CentOS 5.6 VM on Win7 via PHP code

  - by crmpicco

  I am experiencing an issue where my CentOS 5.6 (Final) VM running on Windows 7 has stopped sending emails from my PHP code. I'm confident this isn't a coding issue as I have the exact same code running in my office and emails send correctly from there, hence why I believe this to be a networking/configuration issue. In my /etc/hosts/ file on my VM I have the following: 127.0.0.1 localhost.localdomain localhost 192.168.0.9 crmpicco.co.uk m.crmpicco.co.uk dev53.localdomain When I run setup on my VM the DNS configuration is set to dev53.localdomain and my Primary DNS is 192.168.0.1. In My /var/log/maillog files I see a lot of this sort of thing: Nov 19 14:36:58 dev53 sendmail[21696]: qAJEawI7021696: from=<[email protected]>, size=12858, class=0, nrcpts=1, msgid=<1353335817.9103820024efb30b451d006dc4ab3370@PHPMAILSERVER>, proto=ESMTP, daemon=MTA, relay=localhost.localdomain [127.0.0.1] Nov 19 14:36:58 dev53 sendmail[21693]: qAJEawvd021693: [email protected], [email protected] (48/48), delay=00:00:00, xdelay=00:00:00, mailer=relay, pri=42681, relay=[127.0.0.1] [127.0.0.1], dsn=2.0.0, stat=Sent (qAJEawI7021696 Message accepted for delivery) Nov 19 14:36:59 dev53 sendmail[21698]: qAJEawI7021696: to=<[email protected]>, delay=00:00:01, xdelay=00:00:01, mailer=esmtp, pri=132858, relay=mailserver.fletcher.co.uk. [213.171.216.114], dsn=5.0.0, stat=Service unavailable Is this likely to be a configuration issue?

  Read the article

• Why is OpenSSH not using the user specified in ssh_config?

  - by Jordan Evens

  I'm using OpenSSH from a Windows machine to connect to a Linux Mint 9 box. My Windows user name doesn't match the ssh target's user name, so I'm trying to specify the user to use for login using ssh_config. I know OpenSSH can see the ssh_config file since I'm specifying the identify file in it. The section specific to the host in ssh_config is: Host hostname HostName hostname IdentityFile ~/.ssh/id_dsa User username Compression yes If I do ssh username@hostname it works. Trying using ssh_config only gives: F:\>ssh -v hostname OpenSSH_5.6p1, OpenSSL 0.9.8o 01 Jun 2010 debug1: Connecting to hostname [XX.XX.XX.XX] port 22. debug1: Connection established. debug1: permanently_set_uid: 0/0 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa-cert type -1 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa type 2 debug1: identity file /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa-cert type -1 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3p1 Debia n-3ubuntu5 debug1: match: OpenSSH_5.3p1 Debian-3ubuntu5 pat OpenSSH* debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.6 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-ctr hmac-md5 none debug1: kex: client->server aes128-ctr hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host 'hostname' is known and matches the RSA host key. debug1: Found key in /cygdrive/f/progs/OpenSSH/home/.ssh/known_hosts:1 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: Roaming not allowed by server debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey debug1: Next authentication method: publickey debug1: Trying private key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_rsa debug1: Offering DSA public key: /cygdrive/f/progs/OpenSSH/home/.ssh/id_dsa debug1: Authentications that can continue: publickey debug1: No more authentication methods to try. Permission denied (publickey). I was under the impression that (as outlined in this question: How to make ssh log in as the right user?) specifying User username in ssh_config should work. Why isn't OpenSSH using the username specified in ssh_config?

  Read the article

• What does this mean: "SATP VMW_SATP_LOCAL does not support device configuration"?

  - by Jason Tan

  Can anyone tell me what this means in ESXi 5.1?: SATP VMW_SATP_LOCAL does not support device configuration I've googled it and I get a lot of results, but as yet all the pages that contain the string are discussing other matters. The storage array is a HDS HUS-VM and the hosts are HP b460c G8 blades with flex fabric and flex fabric VCs which I am in the process of commissioning and would like to get it started on the right foot - i.e. error and warning free! naa.600508b1001c56ee3d70da65f071da23 Device Display Name: HP Serial Attached SCSI Disk (naa.600508b1001c56ee3d70da65f071da23) Storage Array Type: VMW_SATP_LOCAL Storage Array Type Device Config: SATP VMW_SATP_LOCAL does not support device configuration. Path Selection Policy: VMW_PSP_FIXED Path Selection Policy Device Config: {preferred=vmhba0:C0:T0:L1;current=vmhba0:C0:T0:L1} Path Selection Policy Device Custom Config: Working Paths: vmhba0:C0:T0:L1 Is Local SAS Device: true Is Boot USB Device: false This is the same LUN: ~ # esxcli storage core device list -d naa.60060e80132757005020275700000016 naa.60060e80132757005020275700000016 Display Name: HITACHI Fibre Channel Disk (naa.60060e80132757005020275700000016) Has Settable Display Name: true Size: 204800 Device Type: Direct-Access Multipath Plugin: NMP Devfs Path: /vmfs/devices/disks/naa.60060e80132757005020275700000016 Vendor: HITACHI Model: OPEN-V Revision: 5001 SCSI Level: 2 Is Pseudo: false Status: degraded Is RDM Capable: true Is Local: false Is Removable: false Is SSD: false Is Offline: false Is Perennially Reserved: false Queue Full Sample Size: 0 Queue Full Threshold: 0 Thin Provisioning Status: unknown Attached Filters: VAAI_FILTER VAAI Status: supported Other UIDs: vml.020001000060060e801327570050202757000000164f50454e2d56 Is Local SAS Device: false Is Boot USB Device: false ~ #

  Read the article

• Cannot connect with Cisco VPN but can connect with ShrewSoft VPN

  - by rodey

  EDIT: We connected an air card to the computer to use a different Internet connection and using the Cisco software, we were able to successfully connect to our VPN server. I just don't understand why the ShrewSoft VPN client would connect but the Cisco connection won't. I'm not our network admin so sorry if I butcher some of the terminology. I have a computer at remote site that connects to our network through Cisco VPN. It uses the Cisco VPN software to do so. The problem is that the computer at this site cannot connect to our VPN because it is getting error "Reason 412: The remote peer is no longer responding." To see if perhaps something on their network was blocking the connection, I installed the ShrewSoft VPN client on the computer, imported our .pcf file and connected with no problem. I have tried two different versions of the Cisco VPN software (4.8.0.* and 5.0.03.*) and have the same problem. I installed Wireshark on the computer and have confirmed (while trying to connect through Cisco) that the computer is trying to contact the VPN server but is not receiving a response. We are not having any other problems regarding users not being able to connect. I'm at a loss at what else to check. I'll be monitoring this and have access to the computer at any time.

  Read the article

• IIS permission configuration issue

  - by Dan

  Sorry the title of this question is a little ambiguous but I don't really have any idea where the issue lies - I'm seeking some clarification of the server error logs. Basically, I had a dedicated server running Windows 2003 and Plesk (v8 I think). Last week the server hardware failed and the entire thing had to be rebuilt from scratch. New hardware was put in, new operating system (Win2008), new Plesk installation (v9.5), new software (MSSQL etc) then all data ported over manually from old C and D drives to restore all 30 client sites. It was hell! All has been okay for a couple of days now but about an hour ago POP! Suddenly all sites went down giving a 500 error. Restarting all services eventually brought everything back online, but I'm now living in total fear. It can - and probably will - happen again. The guys on support gave me the following errors from the server log: The Template Persistent Cache initialization failed for Application Pool 'ASP.NET v4.0 Classic' because of the following error: Could not create a Disk Cache Sub-directory for the Application Pool. The data may have additional error codes.. The worker process for application pool 'domain1.com(domain)(2.0)(pool)' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\domain1.com(domain)(2.0)(pool).config', line number '0'. The data field contains the error code. The worker process for application pool 'PleskControlPanel' encountered an error 'Cannot read configuration file ' trying to read configuration data from file '\\?\C:\inetpub\temp\apppools\PleskControlPanel.config', line number '0'. The data field contains the error code. The support guys are so ambiguous about this and it scares me horribly. Can anyone positively identify the cause of this error which lead to all client website going offline? What can be done to prevent it from happening again? Any pointers would be very much appreciated! Thanks folks...

  Read the article

• Apache 2.2 + mod_fcgid + PHP 5.4: (104) Connection reset by peer

  - by Michele Piccirillo

  On a Debian 6 VPS, I'm running PHP 5.4 via mod_fcgid on a couple of different virtual hosts, managed by Virtualmin GPL. At random, I get 500 Internal Server Errors; restarting Apache brings everything back to normality. Examining the logs, I find messages of this kind: [Thu Oct 04 15:39:35 2012] [warn] [client 173.252.100.117] (104)Connection reset by peer: mod_fcgid: error reading data from FastCGI server [Thu Oct 04 15:39:35 2012] [error] [client 173.252.100.117] Premature end of script headers: index.php Any ideas about what is happening? UPDATE: I found a similar question and the author reported to have solved the problem disabling APC. I tried following the advice, but I'm still getting the same errors. VirtualHost configuration SuexecUserGroup "#1000" "#1000" ServerName example.com DocumentRoot /home/example/public_html ScriptAlias /cgi-bin/ /home/example/cgi-bin/ DirectoryIndex index.html index.htm index.php index.php4 index.php5 <Directory /home/example/public_html> Options -Indexes +IncludesNOEXEC +FollowSymLinks +ExecCGI allow from all AllowOverride All AddHandler fcgid-script .php AddHandler fcgid-script .php5 FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php FCGIWrapper /home/example/fcgi-bin/php5.fcgi .php5 </Directory> <Directory /home/example/cgi-bin> allow from all </Directory> RemoveHandler .php RemoveHandler .php5 IPCCommTimeout 61 FcgidMaxRequestLen 1073741824 php5.fcgi #!/bin/bash PHPRC=$PWD/../etc/php5 export PHPRC umask 022 export PHP_FCGI_CHILDREN PHP_FCGI_MAX_REQUESTS=99999 export PHP_FCGI_MAX_REQUESTS SCRIPT_FILENAME=$PATH_TRANSLATED export SCRIPT_FILENAME exec /usr/bin/php5-cgi Package versions webmin-virtual-server/virtualmin-universal 3.94.gpl-2 apache2/squeeze 2.2.16-6+squeeze8 libapache2-mod-fcgid/squeeze 1:2.3.6-1+squeeze1 php5 5.4.7-1~dotdeb.0 php5-apc 5.4.7-1~dotdeb.0

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

< Previous Page | 361 362 363 364 365 366 367 368 369 370 371 372  | Next Page >