Search Results

Search found 10313 results on 413 pages for 'hardware sharing'.

Page 367/413 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

• Can't install Hyper-V in Windows 8 Pro. Causes boot loop, pain & suffering

  - by Nick

  Hardware: Intel i7 2600K (not overclocked, SLAT compatible, virt. features enabled in bios) Asus Maximus IV Extreme-Z (Z68) 16Gb RAM 256Gb SSD Other non-trivial working parts Adding Hyper-V is causing a boot loop resulting in an attempt at automatic repair by Windows 8 after the second or third loop: I'm trying to get the Windows Phone 8 SDK installed and I've narrowed down my troubles to the Hyper-V feature in Win8. This is required to run the WP8 emulator and there are no install options to omit this feature. My first attempt completely borked the OS as I did not have a recent restore point or system image, so I did a completely clean install and made plenty of backups/restore points. I skipped the SDK install and went straight for the windows feature add-on for Hyper-V. This confirmed that Hyper-V is the issue as the same behavior resulted. I cannot find any hint in the Event Logs. Cancelling automatic recovery causes the same behavior to repeat. I don't have any other VM products installed. My only recourse is to use a restore point, try something else, install it again, and see what happens. No luck so far. I'm on my 10th attempt here. Any help would be much appreciated.

  Read the article

• Offloading backups to secondary network

  - by user1467163

  I'm trying to solve a problem- Currently, we are constantly backing up and have no budget for additional servers. Our production network is still a 10/100 and handles voip, SQL plus our backup traffic, and I'd like to offload the backup traffic onto a secondary network- all of our servers have secondary NIC's that are not in use, and all support gigabit (Our switching hardware does not- a topic for another day). I'd like to move my backups off the production network, but I am having a hard time getting the computers to communicate. I am using a Netgear GS724T switch for the backup network- Chosen for cost and because I have used them extensively on networks saturated with ghosting traffic, so I know it's up to the task. I have defined a VLAN, with ports that are not members of any other VLAN. All traffic is untagged on the VLAN. I have set the servers with 192.168.1.10 and 192.168.1.11 addresses, 255.255.255.0 netmask and I have tried a blank GW, using the local IP of the server 192.168.1.whatever address, and I have tried using the switch's production-side IP as the GW. The machines cannot find each other. DNS addresses are blank because I am going purely by IP for now... Any ideas how to get these machines to talk? they are Windows machines, running Server 2008R2 and 2003R2. Thanks!

  Read the article

• using i7 "gamer" cpu in a HPC cluster

  - by user1219721

  I'm running WRF weather model. That's a ram intensive, highly parallel application. I need to build a HPC cluster for that. I use 10GB infiniband interconnect. WRF doesn't depends of core count, but on memory bandwidth. That's why a core i7 3820 or 3930K performs better than high-grade xeons E5-2600 or E7 Seems like universities uses xeon E5-2670 for WRF. It costs about $1500. Spec2006 fp_rates WRF bench shows $580 i7 3930K performs the same with 1600MHz RAM. What's interesting is that i7 can handle up to 2400MHz ram, doing a great performance increase for WRF. Then it really outperforms the xeon. Power comsumption is a bit higher, but still less than 20€ a year. Even including additional part I'll need (PSU, infiniband, case), the i7 way is still 700 €/cpu cheaper than Xeon. So, is it ok to use "gamer" hardware in a HPC cluster ? or should I do it pro with xeon ? (This is not a critical application. I can handle downtime. I think I don't need ECC?)

  Read the article

• What are good systems for managing PHP/MySQL infrastructure?

  - by sbrattla

  I work in a company which is about to migrate most applications from in-house custom built Java/Tomcat applications to Drupal. Due to company policies, applications and websites need to run on in-house servers. This means that we need infrastructure for Drupal (PHP/MySQL) applications. This must have been solved a million times already. I believe this is what web-hosting companies does every day. Even though we work on a much smaller scale than web-hosting companies, i assume it would make sense to look at the task as if we're going to have an internal small-scale web-hosting company. This means that the guys in IT operations could be "responsible" for "offering" web-hosting, while developers could use these "services". We have three environments; dev(elopment), test and prod(uction). It would make sense that developers could log in to a system and create/edit/delete dev and test sites as they'd like. Production sites should be available through the same system, but only available to IT ops. We need to work with clusters of web servers, meaning that an administration system should be capable of creating/editing/deleting sites across multiple servers. I know there's no "this is it" answer to my question; but what would be a good place to start to get going with this? Apart from the actual hardware, what would be a good administration system for this?

  Read the article

• Why does my computer sometimes not identify my wireless network, or others, that it always connects to?

  - by Emile Erasmus

  I have a vista operating system. Sometimes my computer will not connect to the wireless network (internet) when I start up my laptop. This happens at different places on occasion, and it is very random. It tries to connect, but can not identify the network (it does recognize the wifi name). So at the end it connects, but with limited connectivity. It can not be the hardware because all other computers connect to it fine at the same time. And it happens at different places, mostly home, but sometimes at coffee shops, etc. And then in a day or two when I start up my laptop it is all of a sudden working again. (restart does not solve the problem). I have tried all the trouble shooting options windows offers, restarting the notebook, switch modem on and off, switch laptop wifi on and of, deleted the wifi memory from the laptop and reconnected with the password as if it was the first time, everything. If it does not work at one place it does not mean it won't work at another. Example it won't work at home, then I go to coffee shop and it works, then get back home and it don't. Anyone encountered this before?

  Read the article

• Mac OS X will only upload zero-byte files through FTP

  - by tabacitu

  I'm using Mac OS X Lion and i've been having this problem with FTP (any FTP client, mind you. I tried Transmit, FileZilla, Cyberduck and the Terminal, all with the same result) I can browse files in my FTP Client, but when I upload files, the client hangs for a few seconds, then thinks it uploaded the files successfully, but it only creates a new file with one blank line in it. Sometimes, it manages to upload 4-5 lines. It then returns: 226 - Error during read from data connection 226 Transfer aborted But 2xx is a success message. It is not a server issue, since any Windows machine will upload just fine using the same network. Can anybody figure out what the problem is? It renders my mac useless for web development. The problem persists with SFTP and FTP with SSL/TLS. Later edit: Solved! Ok, turns out the problem goes away when I take out my router and connect directly through PPPoE. So the problem is with the router, I thought. But no, the problem is with the mac that connects through a router that connects through a PPPoE and tries to upload using FTP. Pretty specific, I know. The problem is with the MTU (maximum transmission unit). Apparently, mac os x breaks the file into chunks that are too large for the router to send, because the router's MTU was set lower than Mac OS X's. My router's was 1492, which is ok, but my Mac's MTU was 1500, which is unacceptable. I don't even understand why it works directly with PPPoE. Anyway, if you encounter the same problem, this is how you diagnose and fix it: In terminal, run: ifconfig | grep mtu to see what the MTU is for en0 (or en1, mine was en0) If it's 1500, run sudo ifconfig en0 mtu 1300 This should solve it. If so, it may only be until the next restart. You can also change the MTU in System Preferences \ Network \ Ethernet - Advanced \ Hardware

  Read the article

• Dead Linux server - need help and options

  - by Choi S.

  All, I have a Dell PE 1950 w/ 2 SATA drives in a software RAID1. OS is CentOS 5.5 (2.6.18.x). Starting this afternoon we received HW errors (something on the bus is bad, E171F) and the machine became unresponsive. We hard booted and it came back up for about 5 hours but then it happened again. I'm trying to figure out our options. Unfortunately we do not have similar hardware but I have a small desktop that I can use. I was contemplating putting one of the drives into the desktop and then starting it up. My goal was to then P2V it using Vmware converter but apparently the free v5.x doesn't support hot cloning/converting on a RAID volume, only the Enterprise 4.x version of Converter does. My questions are: 1.) Is putting a single drive out of a RAID1 pair into another piece of HW is safe? Based on my research and understanding it appears to be but would like confirmation. 2.) Is there any work around to the Vmware Converter not supporting RAID volumes during a hot clone/convert session? 3.) Are there other options I'm overlooking? Thanks in advance for reading and responding. --Choi S.

  Read the article

• How to improve Samba performance on VirtualBox machine?

  - by ColinM

  I am running a Windows 7 64bit host and Ubuntu 9.04 32bit guest inside of VirtualBox 4.0.0 on a laptop which has internet connectivity via Wifi. The main use is writing code for which I use Netbeans. My dev environment is hte virtual machine and I use Samba on the VM to share the code directory so that I can use Netbeans on the host as my IDE. Unfortunately Netbeans does a lot of disk access and due to the poor Samba performance it makes the IDE hardly usable. How can I improve performance of the Samba share? On my desktop it isn't so bad but I don't know what the difference would be since they are similar setups (Win 7 hosts, cloned guests, SSDs, Vbox guests using SATA in AHCI mode, etc..). With Bridged networking is the performance between the host and guest limited by the physical hardware (Intel 6200 AGN on laptop)? I switched to Host-only and it didn't seem to improve performance at all. To clarify bad performance, I used 7zip to zip a project directory and got 19kbs to 500kbs depending on the size of the files being zipped. On my desktop it was in the ~10mbs range. Any tips for VirtualBox/Samba configuration to get improve the performance? I am using Samba 3.3.2. Hopefully Samba with SMB2 support will be released soon..

  Read the article

• Why can't a PC with 2 network cards be accessed by hostname?

  - by lewis

  I set up PC with 2 network cards, connected to the same LAN. I can connect to this PC (e.g. by remote desktop) only via ip-addresses. Accessing by hostname does not work. Why is this the case? UPDATE: Full environment 1. PC with 2 hardware network adapters. 2. On this PC installed VMWare Workstation. Created 3 VM's, networked by "bridged" network setting in VMWare. 3. In LAN all ip-addresses given from DHCP. 4. Win2k8 on all hosts (both physical and vitrual). As result: 1. PC has 2 ip-address (e.g. 192.168.1.71 and 192.168.1.72). PC available in LAN by ip-addreses, but not avail by hostname. 2. VM's has own ip-addr on each (e.g. 192.168.1.73, *74, *75 etc). They are available from LAN by their ip's, BUT not by their hostnames. How can I access to PC and to VM's by hostname?

  Read the article

• RAID degraded on Ubuntu server

  - by reano

  We're having a very weird issue at work. Our Ubuntu server has 6 drives, set up with RAID1 as follows: /dev/md0, consisting of: /dev/sda1 /dev/sdb1 /dev/md1, consisting of: /dev/sda2 /dev/sdb2 /dev/md2, consisting of: /dev/sda3 /dev/sdb3 /dev/md3, consisting of: /dev/sdc1 /dev/sdd1 /dev/md4, consisting of: /dev/sde1 /dev/sdf1 As you can see, md0, md1 and md2 all use the same 2 drives (split into 3 partitions). I also have to note that this is done via ubuntu software raid, not hardware raid. Today, the /md0 RAID1 array shows as degraded - it is missing the /dev/sdb1 drive. But since /dev/sdb1 is only a partition (and /dev/sdb2 and /dev/sdb3 are working fine), it's obviously not the drive that's gone AWOL, it seems the partition itself is missing. How is that even possible? And what could we do to fix it? My output of cat /proc/mdstat: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [raid10] md1 : active raid1 sda2[0] sdb2[1] 24006528 blocks super 1.2 [2/2] [UU] md2 : active raid1 sda3[0] sdb3[1] 1441268544 blocks super 1.2 [2/2] [UU] md0 : active raid1 sda1[0] 1464710976 blocks super 1.2 [2/1] [U_] md3 : active raid1 sdd1[1] sdc1[0] 2930133824 blocks super 1.2 [2/2] [UU] md4 : active raid1 sdf2[1] sde2[0] 2929939264 blocks super 1.2 [2/2] [UU] unused devices: <none> FYI: I tried the following: mdadm /dev/md0 --add /dev/sdb1 But got this error: mdadm: add new device failed for /dev/sdb1 as 2: Invalid argument Output of mdadm --detail /dev/md0 is: /dev/md0: Version : 1.2 Creation Time : Sat Dec 29 17:09:45 2012 Raid Level : raid1 Array Size : 1464710976 (1396.86 GiB 1499.86 GB) Used Dev Size : 1464710976 (1396.86 GiB 1499.86 GB) Raid Devices : 2 Total Devices : 1 Persistence : Superblock is persistent Update Time : Thu Nov 7 15:55:07 2013 State : clean, degraded Active Devices : 1 Working Devices : 1 Failed Devices : 0 Spare Devices : 0 Name : lia:0 (local to host lia) UUID : eb302d19:ff70c7bf:401d63af:ed042d59 Events : 26216 Number Major Minor RaidDevice State 0 8 1 0 active sync /dev/sda1 1 0 0 1 removed

  Read the article

• High-performance Academic Server [closed]

  - by PHPsmith

  Suppose I want to build a server for the university's academic interests. The server is dedicated only to a site, where users (students and lecturers) just view and fill the academic data. But at a time (e.g. once a semester), about 12,000 students will access the site simultaneously. Due to limitation of resources, I have to build the server using free software (except for the operating system Windows 7, the university has been prepared). The hardware is also limited to the usual 4-core computers (eg, Ivy Bridge Intel Core i7-3770) with approximately 16GB of memory (DDR3 1600 MHz), equipped with an RJ-45 port (Intel 82 579 Gigabit Ethernet). With all these limitations, I have to choose the software (web server, database, etc) are appropriate for this purpose is achieved. I decided to create a site in PHP. Please help me by answering the following questions based on your expertise. (my prime candidate software to consider after googling) Web server which is faster & stable & secure, when implemented and optimized for PHP? And why? (nginx) PHP accelerator which is faster & stable & compatible with the selected web server? And why? (APC with Zend Optimizer+) Database which is faster & stable & secure, when implemented and optimized for selected web server and selected PHP accelerator? (MySQL) Are there any errors that have been or will be happening from my condition is? If there is, please enlighten me? Is there anything else I need to know in order to achieve this goal? If there is, please enlighten me? I understand that the performance also depends on the implementation of source-code program, so I assume it will create a site with the best efficiency (e.g. using AJAX).

  Read the article

• No sound out of headphone port

  - by Thanatos

  I cannot get sound out of the headphone port. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller

  Read the article

• How To Monitor Home Wireless Network Connected Devices Bandwith

  - by GWLlosa

  (Originally posted on SuperUser, not sure if it might be better suited here) I have in my home a standard Comcast cable internet connection. I have it going from the wall to a cable modem, and from the modem to a late-series Linksys router, which provides wired and wireless networking. The vast majority of the users are wireless connections. For day-to-day tasks, this connection is fully sufficient for all my needs. However, on regular occassions, we have social gatherings that involve many people bringing laptops and other PCs and using the network and internet simultaneously, frequently for gaming. I have no administrative oversight over these machines; they have been known to be riddled with spyware and/or bloatware or be running torrents, legal or otherwise. The only reason I care is that on a regular basis, one of the machines will flatline my internet bandwith, and consume it all in order to upload/download/spam people/whatever. When this happens, the latency of the connections for gaming and the like becomes unacceptable, and everyone suffers. My question is: Is there a system I can set up whereby I can easily monitor the various systems connected to my wireless connection, see how much bandwith each one is using, and for what ends? That way, at a glance, I can spot the offending machine and kick it from the connection, without having to go from machine to machine, checking each one's "bandwith used" properties manually, and dealing with the owner's indignant protests all the while. I understand this will likely involve 3rd-party software and/or hardware; my issue is I don't even know where to begin.

  Read the article

• Decrease in disk performance after partitioning and encryption, is this much of a drop normal?

  - by Biohazard

  I have a server that I only have remote access to. Earlier in the week I repartitioned the 2 disk raid as follows: Filesystem Size Used Avail Use% Mounted on /dev/mapper/sda1_crypt 363G 1.8G 343G 1% / tmpfs 2.0G 0 2.0G 0% /lib/init/rw udev 2.0G 140K 2.0G 1% /dev tmpfs 2.0G 0 2.0G 0% /dev/shm /dev/sda5 461M 26M 412M 6% /boot /dev/sda7 179G 8.6G 162G 6% /data The raid consists of 2 x 300gb SAS 15k disks. Prior to the changes I made, it was being used as a single unencrypted root parition and hdparm -t /dev/sda was giving readings around 240mb/s, which I still get if I do it now: /dev/sda: Timing buffered disk reads: 730 MB in 3.00 seconds = 243.06 MB/sec Since the repartition and encryption, I get the following on the separate partitions: Unencrypted /dev/sda7: /dev/sda7: Timing buffered disk reads: 540 MB in 3.00 seconds = 179.78 MB/sec Unencrypted /dev/sda5: /dev/sda5: Timing buffered disk reads: 476 MB in 2.55 seconds = 186.86 MB/sec Encrypted /dev/mapper/sda1_crypt: /dev/mapper/sda1_crypt: Timing buffered disk reads: 150 MB in 3.03 seconds = 49.54 MB/sec I expected a drop in performance on the encrypted partition, but not that much, but I didn't expect I would get a drop in performance on the other partitions at all. The other hardware in the server is: 2 x Quad Core Intel(R) Xeon(R) CPU E5405 @ 2.00GHz and 4gb RAM $ cat /proc/scsi/scsi Attached devices: Host: scsi0 Channel: 00 Id: 32 Lun: 00 Vendor: DP Model: BACKPLANE Rev: 1.05 Type: Enclosure ANSI SCSI revision: 05 Host: scsi0 Channel: 02 Id: 00 Lun: 00 Vendor: DELL Model: PERC 6/i Rev: 1.11 Type: Direct-Access ANSI SCSI revision: 05 Host: scsi1 Channel: 00 Id: 00 Lun: 00 Vendor: HL-DT-ST Model: CD-ROM GCR-8240N Rev: 1.10 Type: CD-ROM ANSI SCSI revision: 05 I'm guessing this means the server has a PERC 6/i RAID controller? The encryption was done with default settings during debian 6 installation. I can't recall the exact specifics and am not sure how I go about finding them? Thanks

  Read the article

• Rescue system running TFS that BSODs, into vmware esxi

  - by 3molo

  Hi, After moving to new facilities, one of our old Dell servers running Windows Server 2003 R2 on PowerEdge 2650 HW BSODs with 0x8e. The server runs Team Foundation Server, so we have a few guys dependent on it. No one here knows TFS, so we have no idea how difficult it would be to setup from scratch. We have the MSSQL database(s) backed up, recent and fresh copy. Tried removing/refitting memory modules, but with no success. The system boots into safe mode but hangs occasionally. I booted a linux livecd and did a dd of both c: and d:, so I have all the data in compressed images on a vmware machine. For the guest, I created a 38G (actually it became 40GB) partition to act as C:, and booted a live cd. I then uncompressed the compressed disk image of c: and dd'd it to the new c: using 'gunzip -dc c.img.gz | dd of=/dev/sda1 bs=1M'. The operation ran for about 1000 seconds, and completed successfully. I assumed it would at least try to boot windows (but most likely BSOD due to not having correct drivers), but the Vmware ESXi guest does not seem to recognize it as a bootable disk. We don't have the vmware enterprise license, so the vmware converter cold cloning is not an option. Did I do something wrong in my dd's etc with the ISOs, or why would it not (try to) boot? Am I wasting my time? What other approach is there? Will continue to try to remove services and drivers to make the physical machine at least work reasonably well in safe mode. What do you suggest? 1. Continue to get the dd'd images to the virtual disk and get it to boot. 2. Install a new windows server, get team foundation server and restore from backup. 3. Focus on the old problematic hardware Any help appreciated

  Read the article

• Latitude D600 USB port problem

  - by Moab

  Both USB ports stopped communicating on my D600, they have power, my optical mouse still lights up, no device works on the ports, everything is fine in Device manager in Dual boot XP and W7. Checked the bios, not much in there for USB. No usb device shows up when I use the F12 boot device menu either, so it must be some hardware issue. I have another hard drive with Ubuntu on it, popped it in and USB does not communicate with it either. Appears to have 5v but no communication, any Ideas besides another motherboard or USB card for the pcmcia slot (these don't work to well from my research)? I mostly use them for mass storage devices and pcmcia slots don't supply enough power for these devices. Thanks to all who answer with last ditch efforts. I hate to give up on it, its been good to me and still runs rather well for its vintage. EDIT: I did inspect the ports with a flashlight and did a partial disassembly of the laptop in an attempt to check the solder joints, but would require complete motherboard removal to see them, that is where I stopped. .

  Read the article

• My new SSD is causing issues. How can I solve them?

  - by Allan

  Computer specs 1 TB harddisc 120 GB 520intel SSD 8 GB DDR3 RAM Athlon Phenom II x64 955 3. 2ghz DK DFI Lanparty FX7900 M3H3 motherboard ASUS ATI RADEON HD6970 2 GB I have bought a new SSD (Intel 520, 120 GB), and wanted to use this as my system disc. I removed the other harddisc, and installed the SSD with the newest firmware. And then Windows 7 I updated Windows 7 with no problems and then put back my old harddrive. I formatted that old harddrive just to clean up at the same time... So at this stage everything was perfect. My new SSD was set as Master 0 Primary it boots on it and I have 1 TB emptyu harddrive I can use for whatever I want. So far no errors at all Now here is the problem, I installed a few games and everytime I tried to play the computer would say Windows must restart because DCOM server process launcher service terminated, or it says Windows must now restart because the Plug and Play service terminated unexpectedly Most commonly this error is caused by a rootkit virus, well I have tried formatting my entire computer, and running every antivirus I could find, so that shouldn't be it. I've also read somewhere it might happen when there are hardware issues. That on the otherhand would make sense, as I just put in a new SSD. I don't expect you to know this error. I haven't found anyone who knew it yet. maybe you can me guide through what might have gone wrong when I placed in the SSD? What have I checked regarding the SSD? It displays the right name when the computer starts up It has the newest firmware Did a 'sfc /scannow' which told me everything was fine I don't know what to do from here. Everything seems to work great with the drive. when I start playing games my computer crashes.

  Read the article

• What is the solution to enable Dymo Turbo 400 Label Printer to work on Win 7 / 64-bit?

  - by mdpc

  It's Christmas time and time for printing labels for all those Christmas cards. I've upgraded to Windows 7 64-bit from XP. I've been unsuccessfully attempting to get the connected Dymo 400 Turbo label USB printer to work again. The latest manufacturer drivers have been successfully loaded and installed. The drivers are supposed to work on Windows 7/64-bit. The Win 7 system(s) in question are patched and up-to-date on that score. The Windows Update site responds with a driver when the USB cable is connected to this printer. The printer queue seems to be established correctly. What happens is that I submit a job to the printer (either using the DYMO s/w or not), it delays for a period of time, and then I get the message 'printing error'. Can't seem to locate the appropriate error in the new and improved event log. Several combinations of rebooting, re-installation and power cycling components fail to make the printer work. Sometimes during some type of reset it spits out the last thing to be submitted, but that seems intermittent. I have tried different USB cables and different USB (2.X) ports as well. I have run the Windows 7 troubleshooter it tries to fix the problem but alas it doesn't. Interestingly, trying the USB printer (and its associated manufacturer drivers and s/w) on another Windows 7 64-bit system has the identical failures noticed on the original system. I did not find anything on the manufacturers' site concerning this problem. The printer has no hardware problems or issues.

  Read the article

• Intel Motherboard Lightning Victim Dies Hard

  - by Stetson RDT

  Today, I have a more hardware-related question. I have an Intel board, and I really do not know which board it is, I built the machine for a relative, but he forgot to keep the documentation. Long story short, the computer was disconnected during a lightning storm, but a lightning strike travelled in via the ethernet cable (It was directly connected to a power brick commonly seen on those long distance ISP Wireless transmitters), and the motherboard was shocked. I am attempting to get this PC going. The problem is as follows: The computer will randomly reboot, just in the middle of anything as it pleases. May load to EFI (or whatever BIOS is nowadays), may load to bootloader, may even get to the OS. But before 5 minutes is up, the system will always die. Out of curiosity, I plugged my voltmeter in to a molex connector. On the 5V side, it gets a good, consistant +5.13V. On the 12V side, it fluctuates, as follows: Upon immediate startup, it soars to 12.11-12.13V. It will now do one of two things: it will immediately jump down to 12.04-12.05V, or hover for about a minute at 12.11-12.13, then jump down. It seems the longer the voltage stays at 12.11-12.13, the shorter the machine will stay running. Also, post codes, whenever the machine locks up, but does not die hard, seem to be between "AA" and "AC". Does this make any sense to anybody? Do you all think this motherboard is salvageable? It was an expensive bugger, and I'd prefer to not replace it.

  Read the article

• Obtaining clear cable signal with Hauppage 1191-950Q TV Tuner

  - by Kyle B.

  I bought a Hauppauge 1191 WinTV-HVR-950Q TV Tuner a while back, and I am attempting to use it to watch TV in Windows Media Center. I do not have cable TV, however I used to have Comcast. Through experimentation, I found that connecting my coax cable into my TV, I was able to view television (i.e. 2-1 = CBS, 5-1 = NBC, etc). This also works on a second TV I use in another room. When I connect the coax cable to my TV Tuner stick and scan TV channels in Windows Media Center, it only picks up 1 station (like 81 or something). My only conclusion on this is somehow the hardware in the television is decrypting a signal that the TV tuner stick is not able to. Is that possible? Should I try a different TV tuner? Any assistance would be appreciated. I also bought a Terk HD Indoor Antenna but my reception has been flakey, so I would rather go this route if possible.

  Read the article

• DRBD as a block device for XEN VM (Centos 5.3)

  - by SaberTooth

  Hi all, I have setup a drbd resource between 2 server nodes - everything works correctly when doing sync tests between the two. (I want to create a HA cluster using drbd,xen and heartbeat) However, when I try and create a XEN VM with Centos as guest operating system, I get through to the partitioning screen on the install but when I select a partitioning type the next screen gives me the following error : "An error has occurred - no valid devices were found on which to create new file systems. Please check your hardware for the cause of this problem." This is the first time attempting create a setup like this and searching Google does not help much... my config files for DRBD and XEN.... DRBD (just the section that is pertinent) on xennode0 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; flexible-meta-disk internal; } on xennode1 { device /dev/drbd0; disk /dev/sda5; address X.X.X.X:7788; meta-disk internal; } XEN kernel = "/boot/xeninstall/vmlinuz" ramdisk = "/boot/xeninstall/initrd.img" extra = "text" name = "VM" maxmem = 3000 memory = 3000 vcpus = 4 on_poweroff = "destroy" on_reboot = "restart" on_crash = "restart" vfb = [ ] disk = [ "phy:/dev/drbd0,sda1,w", "tap:aio:/srv/xen/xenswap.img,sda2,w" ] vif = [ "mac=00:16:3e:11:67:ae,bridge=xenbr0" ] root = "/dev/sda1 ro" Thanks in advance!

  Read the article

• SBS DC DNS entries going missing?

  - by Chris W

  I've been looking at a problem on a friends SBS (2003) server where the client PC's aren't able to connect to the server with a variety of errors reported. Checking the server itself the only indicator of an issue is an error 5782: Dynamic registration or deregistration of one or more DNS records failed with the following error: No DNS servers configured for the local system. Running a dcdiag reports that there are no DNS records registered for the DC so I fixed the problem by doing a netdiag /fix after which the dcdiag comes back clean and clients are ok again. It happened a few weeks ago as well and the same fix solved it. What are the possible causes of the DC DNS entries going missing? Is this a config option that needs tweaking or could it be solved by something simple like scheduling the SBS server to re-boot periodically? The only change they can think of that was made near to the time of the first instance of this problem occurring is that RRAS was started up to allow for a VPN connection from a home user. NB - The server is setup with a pair of NICs in a team so the server has a single virtual NIC providing both LAN/WAN connections to it. An external hardware firewall is in use rather than the windows firewall.

  Read the article

• Microsoft Deployment Toolkit 2012 Error

  - by Jacob Schaer

  I just started with MDT2012 recently in hopes of eventually getting away with using Ghost to deploy all of our department computers. When I test deploy in VirtualBox, it deploys the OS properly, but stops because of a network driver failure (it gets the "could not allocate resources" issue). On physical hardware (Latitude E6500, Optiplex 980, and an older Latitude) it gets through the multicast and stops immediately after with: "Setup was unable to create a new system partition or locate an existing system partition. See the Setup log files for more information" I've looked at the logs and never see anything really of note. Originally I was using DriverPacks from DriverPacks.net, but thinking it was a driver issue, I switched over to using Dell's cab driver packs. Still the same issue. I check and it did the HDD is all fine - it was properly partitioned, set to bootable, and was loaded with all the proper OS installer files. I'm using a flash drive to do the install - when I make changes to the deployment share I rebuild and copy the ISO to the drive, then use YUMI multiboot to start the ISO (probably irrelevant).

  Read the article

• Installed Windows 7 Ultimate on D Drive and previous Windows 7 Enterprise on C Drive has stopped starting up

  - by teenup

  Please please help! I have installed Windows 7 Ultimate on same hard drive on D Drive on my laptop and the previous Windows 7 Enterprise which was installed on C Drive is not booting up now. When I turn on my laptop, I see two Windows 7 on the screen, when I select newer one, it starts, but when I select older one which is Enterprise edition, system won't start and I get the DOS black screen with this error message: Windows Boot Manager Windows failed to start. A recent hardware or software change might be the cause. To fix the problem: Insert your Windows installation disc and restart your computer. Choose your language settings, and then click "Next." Click "repair your computer." Info: The boot selection failed because a required device is inaccessible. I notice that when I run the newer OS installed, the previous OS's drive (Which is D: now instead of C:) has become unusable and when I double click it, it asks me to format the drive. The data, that I had on my D Drive (Which is now C Drive for new OS), I had copied it to a network path and it is available. It was containing Windows 7 Users folder which I copied at that time when installing new windows. I have copied that Users folder again to the new OS's C Drive thinking it would run again, but of no use. Please please please...if someone can help...It is extremely required for me. Thanks a lot in advance.

  Read the article

• why would resetting the Netgear N300 router fix my Win 7 laptop's slow wifi?

  - by rjnagle

  In the past day the wifi download speeds of my Win 7 HP 64 bit laptop have slowed considerably. I am trying to troubleshoot the problem and to figure out whether it's hardware related (i.e., is the Intel(R) Centrino(R) Wireless-N 2230 the problem?) or router related. I have a Netgear N300 router connected to my modem. I'm using Speedtest to measure my speed. First, during my problem state, my ipad can download and upload at normal speeds. It's only my Win 7 laptop which is having problems. Because my ipad downloads at normal speeds, that would tell me that the problem is specific to the laptop (either HW or SW). But when I restarted my Netgear router, the laptop wifi problems disappeared. That just doesn't make sense. If we know that one device can connect properly to the router, why would a laptop have problems? What are some possible reasons why this might happen? Also, during my problem state, I noticed that on my laptop upload speeds were faster than my download speeds. Anybody have a guess about what might cause upload speeds on one device to be faster than another? Is there any actions i could take (or options to enable) so this problem won't occur. (I initially thought my problem might be software related or memory related -- Norton AV or browser plugins. But even after I disabled everything and made sure memory footprint was minimal, the slowdown was still occurring -- and it solved itself altogether when the router was reset).

  Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >