Search Results

Search found 11331 results on 454 pages for 'resource monitor'.

Page 367/454 | < Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• will heavy network traffic affect other connections on HP ProCurve V1810-48G?

  - by nn4l

  I have a HP ProCurve V1810-48G switch with a few servers connected to it (everything in one rack). The switch is practically in its default configuration. During copying of a few hundred GByte of data from server_a to server_b (using tar cf - data | ssh server_b 'cd myhome; tar xf -'), essentially saturating the network capacity between those two servers, I noticed network related error messages on the console of server_c - as if server_c is no longer able to send/receive traffic to server_d. After canceling the copy command everything was normal again. I would understand this if the network connection would use a shared resource, for example if server_a and server_c are in one datacenter, server_b and server_d are in another datacenter and both datacenters are connected with a 100 MBit line. But all of the mentioned servers are connected to the same switch and are located in the same IP network. I always thought that a connection between two servers on one switch will not affect any other server connected to the switch. It is also possible that the network related error messages are caused by something else - but I can't risk a network problem for any other system on this switch. Please advise.

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• SNMP Access on Ubuntu

  - by javano

  I am trying to use SNMP to monitor a machine locally on its self and remotely. This is the snmpd.conf (Ubuntu 8.04.1): # sec.name source comunity com2sec readonly 1.2.3.4 nicenandtight com2sec readonly 5.6.7.8 reallysafe group MyROGroup v1 readonly group MyROGroup v2c readonly group MyROGroup usm readonly view all included .1 view system included .iso.org.dod.internet.mgmt.mib-2.system access MyROGroup "" any noauth exact all none none syslocation my house syscontact me <[email protected]> exec .1.3.6.1.4.1.2021.7890.1 distro /usr/bin/distro smuxpeer .1.3.6.1.4.1.674.10892.1 includeAllDisks 95% 1.2.3.4 is the local machines IP and everything is working locally. 5.6.7.8 is the remote machine and initially I am just trying to touch SNMPD with snmpwalk from the remote machine; snmpwalk -v 2c -c reallysafe 1.2.3.4 Timeout: No Response from 1.2.3.4 I have added to iptables as the very first rule; -A INPUT -p udp -m udp --dport 161 -j ACCEPT With such a loose iptables rule I can't see why I can't even touch the SNMPD on that Uubuntu Machine. There are more specific rules further down the table but as I couldn't connect I added the above. TCPDump shows the UDP packets coming in. What could be going wrong here?

  Read the article

• DRBD setup problem

  - by cuthieu

  I'm so new to DRBD, please help me fixing the problem below. Enclosed my drbd.conf. Many thanks [root@skonkwerks1 ~]# drbdadm create-md all open(/dev/hdb3) failed: No such file or directory Command 'drbdmeta /dev/drbd0 v08 /dev/hdb3 internal create-md' terminated with exit code 20 drbdsetup exited with code 20 [root@skonkwerks1 ~]# vi /etc/drbd.conf global { usage-count no; } resource repdata { protocol C; startup { wfc-timeout 0; degr-wfc-timeout 120; } disk { on-io-error detach; } # or panic # net { cram-hmac-alg "hdd1"; shared-secret "testing"; } syncer { rate 10M; } on skonkwerks1 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.1:7788; meta-disk internal; } on skonkwerks2 { device /dev/drbd0; disk /dev/hdb1; address 172.29.156.2:7788; meta-disk internal; } }

  Read the article

• SQL Server becomes slow after restart

  - by Tobi DM

  I already posted this one on stackoverflow but someone gave me the hint to that I might have more luck on serverfault. We use SQL Server 2005 on an Windwos Server 2008. Ther Server has 48 GB RAM. SQL Server is configured to use 40 GB RAM. There is only one database hosted (About 70 GB). The only app beside SQL Server is our App-Server which connects the clients to the database. Now we encounter the following problem: After a restart of the server our the performance is great. The server grabs the 40 GB RAM wich it is allowed to and then runs fast as hell. But after about 4 weeks the system becomes slower and slower. The execution of statements (seen in the profiler) is raising slowly. But I cannot see that there is something going wrong on the server. CPU usage is at about 20% I/O also seems to be no Problem The process monitor does also not show that there are strange apps or something like that. Eventlog does also have no interessting messages No open transactions or blockings to see We do not use cursors in our app We tried already the following things without effect: Droped the cache by using the statements DBCC FreeProcCache DBCC FREESYSTEMCACHE('ALL') DBCC DropCleanbuffers Restarted the Appserver we are using. Restart the sql server service But nothing did help exept restarting the whole server. Any ideas?

  Read the article

• CentOS 6.3 Virtual under OpenVZ cannot ping, host lookups, outbound connections while postfix running

  - by Paul Cravey

  My best theory is that some kernel limit is being hit preventing outbound connections. We have tried basically everything from tcpdumps to provisioning an entirely new virtual server (we do not have this problem on any other virtuals), however the problem somehow carried over, even with new postfix build (working). Emails work, and outbound connections work, so long as postfix does not have too much going on. /proc/user_beancounters shows no limits being hit (show below). Nevertheless, pings fail even to IP addresses. TCP stack appears healthy. Load is low. No iowait. Flushed iptables already. Has anyone experienced anything like this? uid resource held maxheld barrier limit failcnt 3: kmemsize 166216365 170262528 9223372036854775807 9223372036854775807 0 lockedpages 0 0 9223372036854775807 9223372036854775807 0 privvmpages 285727 351885 9223372036854775807 9223372036854775807 0 shmpages 16933 17605 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 numproc 150 303 9223372036854775807 9223372036854775807 0 physpages 314156 326191 0 1280000 0 vmguarpages 0 0 9223372036854775807 9223372036854775807 0 oomguarpages 165355 165355 9223372036854775807 9223372036854775807 0 numtcpsock 89 172 9223372036854775807 9223372036854775807 0 numflock 22 76 9223372036854775807 9223372036854775807 0 numpty 1 2 9223372036854775807 9223372036854775807 0 numsiginfo 0 75 9223372036854775807 9223372036854775807 0 tcpsndbuf 2733472 4371752 9223372036854775807 9223372036854775807 0 tcprcvbuf 1798336 5427296 9223372036854775807 9223372036854775807 0 othersockbuf 491120 1000760 9223372036854775807 9223372036854775807 0 dgramrcvbuf 0 238728 9223372036854775807 9223372036854775807 0 numothersock 361 505 9223372036854775807 9223372036854775807 0 dcachesize 135941831 136114679 9223372036854775807 9223372036854775807 0 numfile 2905 4990 9223372036854775807 9223372036854775807 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 dummy 0 0 0 0 0 numiptent 8 9 9223372036854775807 9223372036854775807 0 [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. --- 4.2.2.1 ping statistics --- 9 packets transmitted, 0 received, 100% packet loss, time 8493ms [root@bni /]# service postfix stop [root@bni /]# ping 4.2.2.1 PING 4.2.2.1 (4.2.2.1) 56(84) bytes of data. 64 bytes from 4.2.2.1: icmp_seq=1 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=2 ttl=53 time=8.62 ms 64 bytes from 4.2.2.1: icmp_seq=3 ttl=53 time=8.63 ms 64 bytes from 4.2.2.1: icmp_seq=4 ttl=53 time=8.66 ms Outbound connections of all sorts fail when postfix is running.

  Read the article

• Massive Memory Leaks?

  - by Mads

  Hi, I seem to have huge memory leaks, which are confusing me. I'm running fusion 3.1 / Windows 7 on Snow Leopard. It's a clean install with all upgrades applied. I've given fusion 8GB on a 14GB machine. I've installed VS2008 & Eclipse in Windows 7. Nothing unusual. Inside Task Manager in Windows 7, my memory footprint stays reasonable, at <2GB. But in OSX, Activity Monitor shows the footprint of vmware-vmx to be much larger. It starts at 2 GB, which seems fine, but whenever I'm actually doing anything in Windows, vmware-vmx's footprint grows at a few MB per second. After 20 mins or so it's using ~10GB and everything grinds to a halt. Throughout this, Task Manager still says I'm only using 2GB. And whatever I do in windows seems to increase vmware-vmx's memory footprint. Even closing down an application seems to make it go up. So is this par for the course in fusion? I was previously using parallels 3 / Vista under Leopard, and it worked fine. I'd assumed my new fusion config would work better, but this makes it completely unusable. (And apparently I can't even ask tech support unless I buy a support package...) Any advice much appreciated. Thanks

  Read the article

• Change Windows 7 Explorer's Details Pane limits

  - by Paul

  For some reason, MS decided to completely kill the status bar's functionality in Win7 (and maybe Vista, but I don't know for sure). I have tried all possible options such as Classic Shell and so on. Basically, the one thing I miss most is seeing at a glance the total size of my selected files. I know I can press Alt+Enter or whatever, but that's not the point. The point is that the so-called 'details' pane stops providing details if more than 15 files are selected! WTH? Cannot understand the reason behind such a stupid arbitrary limit, that doesn't seem to be user-configurable at all. Anyway, what I'm looking for is a way to change that limit, either via the registry or otherwise. If changing the limit isn't possible, would it be possible for some programming genius to create a very small optimized light-weight non resource-hungry (you get the idea!) program whose sole purpose will be to automatically click the "Show more details..." link in the details pane after every file selection? For bonus points, the program should wait for a second or two after file selection is complete to do this, so that selecting multiple files in quick succession doesn't hit the HDD repeatedly. Any takers for the challenge? :)

  Read the article

• Plone site randomly serving wrong content

  - by Chris Miller

  I have a Plone site that has begun to randomly serve up the wrong content. Any given content suddenly shows something else. Sometimes a JPEG loads a stylesheet instead or a stylesheet loads as a page or a page as an image. The images move around, some times our site logo shows a bullet, or one of the other site images. Fiddler shows the wrong content in the response, the apache logs show the content type of the incorrect file (so if the an image loads in place of a style sheet, apache shows that). We thought mod_proxy was the source of our grief, but we get the problem hitting Zope directly. I never get the wrong content using the Medusa Monitor to repeatedly hit the content. I do see ConflictErrors in the instance.log file, and they seem to be correlated to the problem, but not 100%. ZPublisher.Conflict ConflictError at \path\to\object: database conflict error (oid 0x3586, class BTrees._OIBTree.OIBTree, serial this txn started with blah, serial currently committed blah) (X conflicts (0 unresolved) since startup blah) I pulled that off the web, it's not from our logs, but it's the same message. This may be a red herring, it sounds like those messages are normal. We've updated to the 3.3.5, same problems. I'm at a loss. I'm wondering if there a good way to intercept what is being served? Secondly, is there a way to increase the verbosity of the access log to included the content-type? I've even seen the problem manifest in ZMI. It happens more often when we're authenticated. Sometimes it can take a thousand reloads to see the problem, other times it happens in different ways every time we reload. I believe we've seen this problem for a couple years, but it was very intermittent, a page would show the content of a GIF, then a reload later wouldn't happen for a long time. Now it's a huge problem.

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Windows Action Center notification icon says Backup in Progress when no backup is occurring

  - by allquixotic

  How can I get Windows Action Center's little flag in the notification area to stop saying "Backup In Progress" on Windows 8? It's driving me nuts. I disabled the Windows Backup service completely and turned off File Recovery. Nothing that I can tell is using any disk I/O whatsoever, by examining Task Manager's resource monitor. It's just a visual cue that seems totally wrong considering my disk is only using about 50 KB/s of sporadic writes for superfetch etc. This wouldn't be a problem for me, since I rely on the knowledge that the Backup service is disabled and there's no disk activity, but I am trying to support a more traditional user who relies on visual cues from the operating system and trusts them over low-level observations like "...but the Windows Backup service is disabled!" Therefore this user still thinks that the backup is going on, even after the service is disabled. Technically, I think this is a bug in Windows 8. It really should not be displaying "Backup in Progress" if ... you know ... a backup, is not, in progress. Which it isn't. Is there a workaround?

  Read the article

• Windows Server 2012 Hyper-V very slow

  - by Matt Taylor

  I have been running several Hyper-V VMs on Windows Server 2008 R2 for the past couple of years and enjoying perfectly adequate performance for my testing/development/r&d environments. I'm a software developer so my hardware knowledge is basic however I built the rig using: •Gigabyte GA-X58A-UD3R Intel X58 (Socket 1366) DDR3 Motherboard •Intel Core i7 960 3.20GHz (Bloomfield) (Socket LGA1366) •24GB triple channel RAM The host OS is running on an OCZ SSD and all the VMs are running on a 2TB Marvell SATA3 RAID 0 array consisting of 2 Western Digital Caviar Black 7,200rpm drives. I have tested the speed of the 2TB drive and appear to be getting less than 3Mbs but it can adequately run a 4 VM farm including a DC, (SQL) database and IIS application servers. I recently upgraded the SSD on which the host runs to a 256GB OCZ Vertex 4 and took the opportunity to upgrade to Windows Server 2012 and installed the Hyper-V role. I tried importing one of my existing Windows Server 2008 R2 VMs (and converted it to .vhdx) plus I have tried creating a brand new Windows Server 2008 R2 VM but both are running extremely slowly and I can see nothing obvious using the host and guest Task Manager/Resource Monitor tools. In both cases the VM has 8GB RAM (fixed), 4 CPUs, fixed size HD (not expanding) and is using an external virtual network running on a separate NIC to the host. I have upgraded the BIOS to the latest available version and checked the virtualization settings. I have run out of "obvious" (to a developer) things to check/configure and my next option will be to re-install the host OS but before I do I would very much appreciate any advice from any experts out there. Thanks

  Read the article

• Port 22 is not responding

  - by Emanuele Feliziani

  I'm trying to make the jump to VPS from shared hosting for better performances and greater flexibility, but am stuck with the fact that I can't access the machine via ssh. First of all, the machine is a CentOS 6.3 cPanel x64 with WHM 11.38.0. Sshd is running (it appears in the current running processes). Making a port scan I see that port 22 is not responding. Port 21 is, but I am not able to access the machine via ftp (I think it's a security measure, but I don't know where to disable/enable it). So, I'm stuck in WHM and have no way to access the configuration of the machine, neither via ssh nor with ftp/sftp. When trying to connect with ssh via Terminal I only get this: ssh: connect to host xx.xx.xxx.xxx port 22: Operation timed out I also tried to access with the hostname instead of the IP address and it's the same. There seem to be no firewall in WHM and I have whitelisted my home IP address to access ssh, though there were no restrictions in the first place. I have been wandering through all the settings and options in WHM for several hours now, but can't seem to find anything. Does anybody have a clue as to where I should start investigating? Update: Thanks everyone. It was in fact a matter of firewall. There was a firewall not controlled by the WHM software. I managed to crack into the console from the vps control panel (a terrible, terrible java app that barely took my keyboard input) and disabled the firewall altogether running service iptables stop so that I was able to access the console via ssh with the terminal. Now I will have to set up the firewall again because the command I ran looks like having completely wiped the iptables. Can you recommend any newby-friendly resource where I can learn how to go about this and what should I block? Or should I just go with something like this: http://configserver.com/cp/csf.html ? Thanks again to everyone who helped me out.

  Read the article

• How to re-add a RAID-10 failed drive on Ubuntu?

  - by thiesdiggity

  I have a problem that I can't seem to solve. We have a Ubuntu server setup with RAID-10 and two of the drives dropped out of the array. When I try to re-add them using the following command: mdadm --manage --re-add /dev/md2 /dev/sdc1 I get the following error message: mdadm: Cannot open /dev/sdc1: Device or resource busy When I do a "cat /proc/mdstat" I get the following: Personalities : [linear] [multipath] [raid0] [raid1] [raid6] [raid5] [raid4] [r$ md2 : active raid10 sdb1[0] sdd1[3] 1953519872 blocks 64K chunks 2 near-copies [4/2] [U__U] md1 : active raid1 sda2[0] sdc2[1] 468853696 blocks [2/2] [UU] md0 : active raid1 sda1[0] sdc1[1] 19530688 blocks [2/2] [UU] unused devices: <none> When I run "/sbin/mdadm --detail /dev/md2" I get the following: /dev/md2: Version : 00.90 Creation Time : Mon Sep 5 23:41:13 2011 Raid Level : raid10 Array Size : 1953519872 (1863.02 GiB 2000.40 GB) Used Dev Size : 976759936 (931.51 GiB 1000.20 GB) Raid Devices : 4 Total Devices : 2 Preferred Minor : 2 Persistence : Superblock is persistent Update Time : Thu Oct 25 09:25:08 2012 State : active, degraded Active Devices : 2 Working Devices : 2 Failed Devices : 0 Spare Devices : 0 Layout : near=2, far=1 Chunk Size : 64K UUID : c6d87d27:aeefcb2e:d4453e2e:0b7266cb Events : 0.6688691 Number Major Minor RaidDevice State 0 8 17 0 active sync /dev/sdb1 1 0 0 1 removed 2 0 0 2 removed 3 8 49 3 active sync /dev/sdd1 Output of df -h is: Filesystem Size Used Avail Use% Mounted on /dev/md1 441G 2.0G 416G 1% / none 32G 236K 32G 1% /dev tmpfs 32G 0 32G 0% /dev/shm none 32G 112K 32G 1% /var/run none 32G 0 32G 0% /var/lock none 32G 0 32G 0% /lib/init/rw tmpfs 64G 215M 63G 1% /mnt/vmware none 441G 2.0G 416G 1% /var/lib/ureadahead/debugfs /dev/mapper/RAID10VG-RAID10LV 1.8T 139G 1.6T 8% /mnt/RAID10 When I do a "fdisk -l" I can see all the drives needed for the RAID-10. The RAID-10 is part of the /dev/mapper, could that be the reason why the device is coming back as busy? Anyone have any suggestions on what I can try to get the drives back into the array? Any help would be greatly appreciated. Thanks!

  Read the article

• How to set up mysql storage for certain rsyslog input matches?

  - by ylluminate

  I'm draining various logs from Heroku to an rsyslog linux (ubuntu) server and am starting to have a little more to bite off than I can chew in terms of working with my log histories. I am needing to be able drill back in time based on more flexible details and more flexible access than what the standard syslog file(s) provide. I'm thinking that logging to mysql may be the correct approach, but how do I set this up such that it pulls only certain log entries into a table based on an identified? For example, I see a long hex string identifying each log entry from a certain Heroku app instance. I assume that I can just pipe those into the mysql socket vs ALL rsyslog input into mysql... Could someone please direct me to a resource that can walk me through the process of setting something like this up or simply provide some details that can help? I have 15+ years of Unix experience so I just need some nudging in the right direction as I've not really done a tremendous amount of work with syslog daemons previously in terms of pooling various servers into one. Additionally, I'd be interested in any log review tools that could make drilling through log arrangements like this more handy for developers.

  Read the article

• KeePass lost password and/or corruption due to Dropbox/KeePassX

  - by GummiV

  I started using Keepass about a month ago to hold my passwords and online accounts info. Everything was stored in a single .kdb file, only protected with a password. I'm using Windows 7. Now Keepass can't open my .kdb file with the error "Invalid/wrong key". I'm fairly confident I have the right password. Altough I might have mixed up a few letters I've tried about two dozen different combinations to minimize that possibility - but can't rule it out though. My guess is however that the .kdb file got corrupted, either due to Dropbox syncing (only using it on one computer though) or because I edited the file using KeePassX on Ubuntu (dual boot on the same computer, accessing a mounted Win7 NTFS partition), or possibly a combination of both. I have tried restoring older versions(even the original one) from Dropbox and trying out all possible passwords without any luck. (which does seem to rule out KeePassX as the culprit, since oldest copies are before I edited the file from Ubuntu) I have tried opening the file with the "Repair KeePass Database file" which always gives the "0xA Invalid/corrupt file structure" (the same error for when a wrong password is typed). I was wondering if there was any way for me to salvage my hard-gathered data. I know generally that brute force cracking is not feasible, but since I can remember probably more than half of the usernames/passwords, any maybe the fact that one of them does come up fairly often (my go-to pass for trivial stuff), that might simplify the brute force process to a doable time frame. Maybe the brute-force thing might incorporate the fact that I know the password length and what characters it's made from. (If we assume corruption, not a password-blackout on my part) I could do some programming if there are any libraries or routines that I could use. Other people seem to have had a similar probem http://forums.dropbox.com/topic.php?id=6199 http://forums.dropbox.com/topic.php?id=9139 http://www.keepassx.org/forum/viewtopic.php?t=1967&f=1 So hopefully this question will become a suitible resource for people when searching the web. Feel free to tell me if you think this should rather be a community wiki.

  Read the article

• Tomato/DD-WRT router to act as switch & only NAT some port

  - by fseto

  BACKGROUND: I have a device that must use a real IP address. Currently, my ISP uses DHCP and I can have up to 4 real IP address assigned. However, the cable modem only have 1 ethernet port and it's connected to my router (running Tomato, but can run DD-wrt or other Openwrt if required). Question stems from how I can connect the additional device, requiring a real IP? EASY SOLUTION: would be to get a switch and connect to the CM, Router, and Device. But alas, I want to avoid this route, since: my wiring cabinet in my home is drawing lots of power and heat already Device will be unprotected by any firewall unable to monitor the traffic to/from device. Besides, what would be the FUN in that? =) IDEA: So what I want to do is to configure the router, so that one of the switchport is removed from the normal br0 bridge. Instead, I want to make it behave like a switch on the WAN port. What's the best way of doing this? Should I create another bridge on the WAN & the device port? Can a single port belongs to two bridges? or would I need to create a subinterface first? Would I need a DHCP-relay? Am I expecting too much from my poor cheapie router? +------+ | CM | +--++--+ || +----WAN---------------+ | / \ Router | | BR1? BR0 | | | \ | | | {NAT} | | | / | | \ | +-P0----P1-P2-P3-Wifi--+ | +------+ |Device| +------+

  Read the article

• IP queue buffer

  - by summerbulb

  I seem to have an issue with IP queue. I have a linux machine that I am using to run some experiments. The linux machine is configured to be a router, having two NICs, connecting two other computers, and managing their network traffic. All incoming packages are captured, using iptables, and analyzed by a C application. The application analyzing the packets has a built-in delay, as part of the experiment. So I have one very fast computer sending packets through my linux-router and a (relatively) slow linux-router that analyses and deals with the packets, one by one. This situation leads to the fact that when I fire up a sender application on one of the computers connected to the linux-router, my IP queue on the linux-router gets filled up (almost) instantaneously. The IP queue's max length is currently set to 1024, and if it overflows, the packets are dropped. This is expected and i'm OK with it. But, (and this is where it gets interesting), every now and then I get the following error: "Failed to receive netlink message: No buffer space available" At start, I thought this was due to the IP queue overflow, but after some analysis i found that sometimes I get the error even if the IP queue buffer did not overflow, and sometime I DON'T get the message even though the buffer DID overflow. When I run > cat /proc/net/ip_queue, I get the following table (also used to monitor the IP queue overflow): Peer PID : 27389 Copy mode : 2 Copy range : 65535 Queue length : 0 Queue max. length : 1024 Queue dropped : 1166875 Netlink dropped : 2916 Looking at the last two values, Queue dropped seems to refer to packets that did not manage to get into the IP queue because the buffer was full. I can see this value rise as I bombard the linux-router. Netlink dropped ( as it's name implies :) ) seems to have to do with the error i'm getting. I did my best to search for material on this error, but wasn't able to find anything that seemed to point me in the required direction. Bottom line: Why am I getting this error and what can I do to avoid it?

  Read the article

• Can't display RSSI values in Wireshark

  - by Giovanni Soldi

  I am trying to analyze the up-link Wireless traffic generated by my Sony Ericsson phone and captured by my D-Link router, on which I installed the DD-WRT firmware. To do this, first I log in the router and enable the prism0 interface by typing the command: wl -i eth1 monitor 1 and then I start to capture the packets by typing: tcpdump -i prism0 ether src xx:xx:xx:xx:xx:xx -s0 -w /tmp/smbshare/sony_ericsson_test.pcap where xx:xx:xx:xx:xx:xx is the MAC address of my Sony Ericsson phone. After a while I transfer the sony_ericsson_test.pcap file to my computer and open it with Wireshark program. In order to display the RSSI values I follow this procedure: Edit - Preferences... - Columns - Press "Add" button - As "Field type" I choose "IEEE 802.11 RSSI" and finally I choose name "Power" and click on "Apply" button. The problem is that the column "Power" is empty with no RSSI values. Does Anyone has a clue on why are RSSI values not displayed? Maybe I am missing a passage. Looking forward to hearing from anyone of you! Thanks in advance for your help!

  Read the article

• Windows 7 notebook turn off by itself, how to check if it is due to CPU being too hot?

  - by Jian Lin

  I have a Dell Studio 15 notebook, and it just started turning off by itself yesterday. Could it be that the CPU is too hot? I have had several notebooks before and every one of them I can put them on the bed without any problem. This Dell Studio Notebook, however, seems like have the air / fan outlet pointed outward from the bottom back of the notebook, so I suspect that the air is partially blocked when it is on the bed. Are there Win 7 tools that can monitor the CPU temperature, or will some 3rd party tool be needed? (I try to stick to official tools nowadays). Also, it is running Win 7 Ulitmate, there is actually no utility or background service from Win 7 or from Dell that detects when the temperature is too hot (or 95% near the max), pop out a message box giving a warning and say that the computer will go into sleep mode in 1 minute, but instead just turn off the computer by brute force (cutting out the power) right then and there? Update: it turned off right in front of my eyes -- it is not doing any windows update or anything. just normal use and jooooop, it turned off.

  Read the article

• EC2 instances keep becoming inaccessible via SSH, can I use elastic loadbalancer to check SSH connectivity?

  - by Rick

  This is mainly an issue for my development ec2 server as it seems that my instance keeps becoming inaccessible via SSH. It happened yesterday so I killed that one and started a new one and happened again later today. The server still works, my web application is accessible in a web browser but whenever I try to connect via SSH I get a pemrission denied (public key) error message in my terminal. I am 100% sure I am doing nothing wrong as I can create a new instance of the exact same AMI (its a personal custom AMI), change absolutely nothing, including using the same .pem key, and then am able to SSH into that new instance using the exact same command as before (just changing the IP address). I understand that ec2 can have issues but having this happen every day seems a bit odd.. I am using an m2.xlarge instance so I don't know if these tend to be unstable, in the past I have used a small instance and had it running for months with no problems which is why I find this so odd. I am looking into using loadbalancing but it seems the only "health" checks they offer is for http or tcp so I'm not sure if I can make it monitor for SSH connectivity. This is important for development as I may make 1-2 new pushes of an application a day and use SSH to do this. I have a designer that needs to have the app always accessible as he works with the front-end files to test output with the live application. Anyways, any advice / info is appreciated

  Read the article

• Deploying ASP.NET MVC to Windows Server 2003

  - by pete the pagan-gerbil

  Hi, I have a problem with an MVC 2 website on Windows Server 2003 running IIS 6. It is externally hosted, but we have a 2003 server internally for testing. The internal server runs the website fine, the external server gives a 403 ("website declined to show this page") error when navigating to the root of the site, and a 404 if I try to navigate directly to a page resource. I have tried the wildcard ISAPI mapping and extension mapping, and a couple of other common checks (I forget exactly which now, most of them were already set correctly), but so far no joy. All the settings can be replicated on our internal server and the pages return properly. IIS logs just show exactly what the browser shows - 404 errors and 403s. I've read about a different level of trust required for an MVC application compared to a WebForms application - how can I check permissions and trust levels on the external and internal servers (assuming I am able to check that) and if that would cause these errors, what are the minimum levels that MVC require? Failing that, what else might be causing this error for me to try out?

  Read the article

• What is the optimum way to secure a company wide wiki?

  - by Mark Robinson

  We have a wiki which is used by over half our company. Generally it has been very positively received. However, there is a concern over security - not letting confidential information fall into the wrong hands (i.e. competitors). The default answer is to create a complicated security matrix defining who can read what document (wiki page) based on who created it. Personally I think this mainly solves the wrong problem because it creates barriers within the company instead of a barrier to the external world. But some are concerned that people at a customer site might share information with a customer which then goes to the competitor. The administration of such a matrix is a nightmare because (1) the matrix is based on department and not projects (this is a matrix organisation), and (2) because in a wiki all pages are by definition dynamic so what is confidential today might not be confidential tomorrow (but the history is always readable!). Apart from the security matrix, we've considered restricting content on the wiki to non super secret stuff, but off course that needs to be monitored. Another solution (the current) is to monitor views and report anything suspicious (e.g. one person at a customer site having 2000 views in two days was reported). Again - this is not ideal because this does not directly imply a wrong motive. Does anyone have a better solution? How can a company wide wiki be made secure and yet keep its low threshold USP? BTW we use MediaWiki with Lockdown to exclude some administrative staff.

  Read the article

• Very high-pitched noise when computer does something intense?

  - by Starkers

  "Intense" is the best word I can use to describe it because I'm not sure what it is, whether it's RAM, GPU or CPU. If I pan the camera in unity: A high pitched noise issues from the computer. The picosecond I start panning the sound starts. Stops the picosecond I stop panning. If I start an infinite loop: 2.0.0p247 :016 > x = 1 => 1 2.0.0p247 :017 > while x < 2 do 2.0.0p247 :018 > puts 'huzzah!' 2.0.0p247 :019?> end huzzah! huzzah! huzzah! An identical high pitched noise can be heard. I don't think it's the GPU due to this simple experiment. Or any monitor-weirdness (although the sound does sound like one of those old CRT monitors if you're old enough to be young when those things were about) The CPU? Or maybe my SSD? It's my first SSD and the first time I've heard this noise. Should I be worried? Regardless, what's causing this sound? I can't think what would cause such high frequency vibrations. I built the PC myself. Not enough heat paste on the CPU? Too much? Just no idea what's going on. Info: CPU Type QuadCore Intel Core i5-3570K, 3800 MHz (38 x 100) Motherboard Name Asus Maximus V Extreme Flash Memory Type Samsung 21nm TLC NAND Video Adapter Asus HD7770

  Read the article

< Previous Page | 363 364 365 366 367 368 369 370 371 372 373 374  | Next Page >