Search Results

Search found 12324 results on 493 pages for 'password encryption'.

Page 369/493 | < Previous Page | 365 366 367 368 369 370 371 372 373 374 375 376  | Next Page >

• Ubuntu 12.04 Freezes at Bootup

  - by Ryan Yu

  I have an Acer Aspire One Model AO722, that has a dual-boot configuration with Windows 7 Home Premium and Ubuntu 12.04. Processor: AMD C-50, 1.00GHz 2.00GB ram, 64-bit, AMD Radeon HD 6250 Graphics. I installed Ubuntu two days ago, and since then, loading it has been sporadic. Windows 7 still loads just fine, but Ubuntu will sometimes freeze. First time I booted Ubuntu up, it ran no problem. Worked with it for half an hour, then shut down the computer. The second time I booted it up, it froze after ten minutes when I was trying to set up Thunderbird. Third time, same thing. Fourth time, it froze about 5 minutes after bootup when I was trying to connect to my wifi. Fifth time, it ran no problems for about 5~ hours. Then, three consecutive times I've restarted (what is it, the 6th, 7th, and 8th times?) it has gotten to the login screen, I've entered my password, all the text on the page disappears as if its going to load my desktop, and it freezes. A minute ago when I booted Ubuntu up for the 9th time, it loaded the desktop fine. Who knows if it'll crash soon; probably, though. Any ideas?

  Read the article

• Ubuntu 12.04 desktop, VNC viewer not refreshing screen

  - by user73279

  I've had this issues across multiple machines and multiple versions of Ubuntu desktop (all 10.04 or later). Usually it happens with an old laptop I've put Ubuntu on but now it's happening on my primary dev machine (a quad-core PC recently upgraded to Ubuntu 12.04 desktop). The problem is this - I can connect to the machine and login with the password, the initial screen looks fine but never refreshes. I can see the monitor for the machine across the room and can see the mouse move and the menus pop up but the image of the screen on the PC in front me running the VNC viewer never updates. So the mouse and keyboard commands are working. Ubuntu 12.04 Desktop Ultra VNC Viewer (also seen with RealVNC's free VNC viewer) Desktop Sharing Static IP on eth0; Dynamic ID on eth1 I think it is an Ubuntu config issue because this PC used to work just fine with 9.04, 10.04, and 11.10 (over the past couple of years). I've also had a couple of laptops that used to have this issue with older Ubuntu's but don't with 12.04. Additional info: The Win7 PC I'm trying to use to control the Ubuntu PC is connected via 2 DLink 8-port gigabit routers. The Ubuntu laptop I usually control via VNC is typically only connected to the network via wireless. The screen refresh is choppy but usable. I've repeated the issue on a Win7 laptop which was connected via ethernet and wireless.

  Read the article

• Shooting Print Quality Pictures with a Camera Phone [Video]

  - by Jason Fitzpatrick

  Camera phones get a lot of grief for being underpowered but in this video tutorial the crew at SLR Lounge shows how basic technique and a good eye overcome all. Last year over at the photo blog FStoppers they put together a video showing off how you could use the iPhone as a fashion camera–essentially arguing that the camera wasn’t as important as the photographer. A lot of people said “Well yeah, but you had professional models and thousands of dollars in lighting equipment!” in reaction to the video. In turn the crew at SLR Lounge decided to make their own video showing that using only an iPhone camera and two reflectors (as well as an attractive but informal model). It of course helps to have some side kicks to help hold up your reflectors but the point still stands about modern camera phones being perfectly capable of good photos. The SLR Lounge iPhone Photo Shoot – A Follow Up Tribute to The FStoppers [YouTube] What is a Histogram, and How Can I Use it to Improve My Photos?How To Easily Access Your Home Network From Anywhere With DDNSHow To Recover After Your Email Password Is Compromised

  Read the article

• Network configuration problem

  - by Musti

  in my dorm I have to change network configuration and then if it is successfull, I have to enter a user name and password for wired internet connection. Anyway, I had many attempts but I couldnt achieve, and please look at my steps and tell me if there is something wrong and at the end there is an error, but I really dont have any idea about this error. (I am a new ubuntu user, and network is far away of my interests) 1) /etc/network/interfaces auto eth0 iface eth0 inet static address 172.030.014.038 netmask 255.255.255.252 network 192.168.2.0 broadcast 192.168.2.255 gateway 172.030.014.038 2) sudo gedit /etc/resolv.conf nameserver 010.050.001.001 nameserver 010.050.001.002 3) /etc/init.d/networking stop Deconfiguring network interfaces... [ OK ] 4) /etc/init.d/networking restart Running /etc/init.d/networking restart is deprecated because it may not enable again some interfaces Reconfiguring network interfaces... 172.030.014.038: Unknown host ifconfig: `--help' gives usage information. Failed to bring up eth0 Note: IP-address, netmask, gateway, Preferred DNS server and Alternate DNS server ara given by the management of Dorm. It wad very easy in windows but I couldnt achieve in Ubuntu. I also tried to edit from "edit connections" but the save button is gray and I cannot save it. Thanks in advance. / Musti

  Read the article

• unable to send mail from postfix on Ubuntu 12.04

  - by gilmad

  I'm trying to send an email through Google from my localhost. (via PHP5.3) But Google keeps on blocking my requests. I tried to follow the solutions given to a few similar questions, but for some reason they do not work. I followed these instructions to configure it - http://www.dnsexit.com/support/mailrelay/postfix.html Now for the config data: my main.cf file looks like that: relayhost = [smtp.gmail.com]:587 smtp_fallback_relay = [relay.google.com] smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = my sasl_passwd looks like that: [smtp.gmail.com]:587 [email protected]:password and that is how the mail.log rows look like: Dec 14 10:24:50 COMP-NAME postfix/pickup[5185]: 1C3987E0EDD: uid=33 from= Dec 14 10:24:50 COMP-NAME postfix/cleanup[5499]: 1C3987E0EDD: message-id=<[email protected] Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: 1C3987E0EDD: from=, size=483, nrcpt=1 (queue active) Dec 14 10:24:50 COMP-NAME postfix/smtp[5501]: 1C3987E0EDD: to=, relay=smtp.gmail.com[173.194.70.109]:587, delay=0.61, delays=0.19/0/0.32/0.1, dsn=5.7.0, status=bounced (host smtp.gmail.com[173.194.70.109] said: 530 5.7.0 Must issue a STARTTLS command first. w3sm8024250eel.17 (in reply to MAIL FROM command)) Dec 14 10:24:50 COMP-NAME postfix/cleanup[5499]: C20677E0EDE: message-id=<[email protected] Dec 14 10:24:50 COMP-NAME postfix/bounce[5502]: 1C3987E0EDD: sender non-delivery notification: C20677E0EDE Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: C20677E0EDE: from=<, size=2532, nrcpt=1 (queue active) Dec 14 10:24:50 COMP-NAME postfix/qmgr[5186]: 1C3987E0EDD: removed

  Read the article

• Can't get wireless working after installing ubuntu 12.10 on acer aspire 5560-7414

  - by markdel

  I have been struggling all day trying different solutions from different posts on how to get my wifi working but none have worked. Any help would be greatly appreciated. Below are some wireless preferences to help find the problem. mark@mark-Aspire-5560:~$ sudo rfkill list all [sudo] password for mark: 0: acer-wireless: Wireless LAN Soft blocked: no Hard blocked: no 1: brcmwl-0: Wireless LAN Soft blocked: no Hard blocked: no *-network description: Ethernet interface product: NetLink BCM57785 Gigabit Ethernet PCIe vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:01:00.0 logical name: eth0 version: 10 serial: 20:6a:8a:7f:63:82 size: 10Mbit/s capacity: 1Gbit/s width: 64 bits clock: 33MHz capabilities: pm msi msix pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.123 duplex=full firmware=sb ip=158.65.194.244 latency=0 link=yes multicast=yes port=twisted pair speed=10Mbit/s resources: irq:16 memory:f0000000-f000ffff memory:f0010000-f001ffff memory:f0050000-f00507ff *-network description: Wireless interface product: BCM43227 802.11b/g/n vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth1 version: 00 serial: 08:ed:b9:01:e0:8b width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.112 latency=0 multicast=yes wireless=IEEE 802.11bgn resources: irq:18 memory:f0100000-f0103fff

  Read the article

• this error appeared when upgrating 12.04 LTS to 12.10 [closed]

  - by habcity

  Possible Duplicate: How do I fix a “Problem with MergeList” error when trying to do an update? ryder@ryder-Q1500M:~$ do-release-upgrade Checking for a new Ubuntu release Get:1 Upgrade tool signature [198 B] Get:2 Upgrade tool [1,200 kB] Fetched 1,200 kB in 6s (6,988 B/s) authenticate 'quantal.tar.gz' against 'quantal.tar.gz.gpg' extracting 'quantal.tar.gz' [sudo] password for ryder: Reading cache A fatal error occurred Please report this as a bug and include the files /var/log/dist-upgrade/main.log and /var/log/dist-upgrade/apt.log in your report. The upgrade has aborted. Your original sources.list was saved in /etc/apt/sources.list.distUpgrade. Traceback (most recent call last): File "/tmp/update-manager-63XThv/quantal", line 10, in sys.exit(main()) File "/tmp/update-manager-63XThv/DistUpgrade/DistUpgradeMain.py", line 237, in main save_system_state(logdir) File "/tmp/update-manager-63XThv/DistUpgrade/DistUpgradeMain.py", line 130, in save_system_state scrub_sources=True) File "/tmp/update-manager-63XThv/DistUpgrade/apt_clone.py", line 146, in save_state self._write_state_installed_pkgs(sourcedir, tar) File "/tmp/update-manager-63XThv/DistUpgrade/apt_clone.py", line 173, in _write_state_installed_pkgs cache = self._cache_cls(rootdir=sourcedir) File "/usr/lib/python2.7/dist-packages/apt/cache.py", line 102, in init self.open(progress) File "/usr/lib/python2.7/dist-packages/apt/cache.py", line 145, in open self._cache = apt_pkg.Cache(progress) SystemError: E:Encountered a section with no Package: header, E:Problem with MergeList /var/lib/apt/lists/us.archive.ubuntu.com_ubuntu_dists_precise-backports_multiverse_i18n_Translation-en, E:The package lists or status file could not be parsed or opened.

  Read the article

• What went wrong with my curl install?

  - by Danjah

  I'm fresher than the prince to Linux, I've been following the instructions here: http://chrisfulstow.com/running-node-js-on-windows-with-virtualbox-and-ubuntu (the link tells what I am generally trying to do). I'm all up and running in VBox, and am at the curl install part, I may have done the curl part a week ago I forget. So I ran this command anyway: danjah@danjah-VirtualBox:~$ sudo apt-get install curl Result: [sudo] password for danjah: Reading package lists... Done Building dependency tree Reading state information... Done curl is already the newest version. 0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Then: $ curl http://npmjs.org/install.sh | sudo npm_install=rc sh Result: fetching: { gzip: stdin: unexpected end of file /bin/tar: Child returned status 1 /bin/tar: Error is not recoverable: exiting now It failed Should I be concerned? How can I test curl? How can I avoid these situations? Perhaps there's a generic way of checking to see if I've already installed packages/etc? Case specific answers and general advice most appreciated. cheers, d

  Read the article

• What is the disadvantage of using abstract class as a database connectivity in zend framework 2 instead of service locator

  - by arslaan ejaz

  If I use database by creating adapter with drivers, initialize it in some abstract class and extend that abstract class to required model. Then use simple query statement. Like this: namespace My-Model\Model\DB; abstract class MysqliDB { protected $adapter; public function __construct(){ $this->adapter = new \Zend\Db\Adapter\Adapter(array( 'driver' => 'Mysqli', 'database' => 'my-database', 'username' => 'root', 'password' => '' )); } } And use abstract class of database like this in my models: class States extends DB\MysqliDB{ public function __construct(){ parent::__construct(); } protected $states = array(); public function select_all_states(){ $data = $this->adapter->query('select * from states'); foreach ($data->execute() as $row){ $this->states[] = $row; } return $this->states; } } I am new to zend framework, before i have experience of working in YII and Codeigniter. I like the object oriented in zend so i want to use it like this. And don't want to use it through service locater something like this: public function getServiceConfig(){ return array( 'factories' => array( 'addserver-mysqli' => new Model\MyAdapterFactory('addserver-mysqli'), 'loginDB' => function ($sm){ $adapter = $sm->get('addserver-mysqli'); return new LoginDB($adapter); } ) ); } In module. Am i Ok with this approach?

  Read the article

• Computer becomes unreachable on lan after some time

  - by Ashfame

  I work on my laptop and ssh into my desktop. I use a lot of key based authentication for many servers for work but recently I couldn't login because ssh would pick up and try all the keys and it stops trying before ultimately falling back to password based login. So right now I am using this command: ssh -X -o PubkeyAuthentication=no [email protected] #deskto The issue is after sometime the desktop would just become unreachable from laptop. I won't be able to open its localhost through IP and today I tried ping'in it and found a weird thing. Instead of 192.168.1.4, it tries to ping 192.168.1.3 which I am sure is the root cause as it just can't reach 192.168.1.4 when its actually trying for 192.168.1.3 Ping command output: ashfame@ashfame-xps:~$ ping 192.168.1.4 PING 192.168.1.4 (192.168.1.4) 56(84) bytes of data. From 192.168.1.3 icmp_seq=1 Destination Host Unreachable From 192.168.1.3 icmp_seq=2 Destination Host Unreachable From 192.168.1.3 icmp_seq=3 Destination Host Unreachable From 192.168.1.3 icmp_seq=4 Destination Host Unreachable From 192.168.1.3 icmp_seq=5 Destination Host Unreachable From 192.168.1.3 icmp_seq=6 Destination Host Unreachable From 192.168.1.3 icmp_seq=7 Destination Host Unreachable From 192.168.1.3 icmp_seq=8 Destination Host Unreachable From 192.168.1.3 icmp_seq=9 Destination Host Unreachable ^C --- 192.168.1.4 ping statistics --- 10 packets transmitted, 0 received, +9 errors, 100% packet loss, time 9047ms pipe 3 Also the ping command message comes in multiple and not one by one. (izx answer's the weirdness I thought there was in ping command.) I did check for desktop, its local IP is still the same, so something is going on in my laptop. Any ideas? P.S. - Laptop runs Ubuntu 12.04 & Desktop runs Ubuntu 11.10 Laptop is connected through wifi to router and Desktop is connected through LAN to router. Update: Even after setting up static IP leases in router settings, I again ran into this issue.

  Read the article

• Is realtime validation of username good or bad?

  - by iamserious

  I have a simple form for the user to sign up to my site; with email, username and password fields. We are now trying to implement an ajax validation so the user doesn't have to post the form to find out if the username is already taken. I can do this either on keyup event or on text blur event. My question is, which of these is really the best way to do? Keyup From the user POV, it would be good if the validation is done as and when they are typing, (on key up event) - of course, I am waiting for half a second to see if the user stops typing before firing off the request, and user can make any adjustments immediately. But this means I am sending way more requests than if I validated the username on Blur event. Blur The number of requests will be much lower when the validation is done on blur event, But this means the user has to actually go away from the textbox, look at the validation result, and if necessary go back to it to make any changes and repeat the whole process until he gets it right. I had a quick look at google, tumblr, twitter and no one actually does username validations on keyup events, (heck, tubmlr waits for the form to be posted) but I can swear I have seen keyup validations in a lot of places too. So, coming back to the question, will keyup validations be too many for server, is it an unnecessary overhead? or is it worth taking these hits to give user a better experience? ps: all my regex validations etc are already done on javascript and only when it passes all these other criteria does it send a request to server to check if a username already exists. (And the server is doing a select count(1) from user where username = '' - nothing substantial, but still enough to occupy some resource) pps: I'm on asp.net, MS SQL stack., if that matters.

  Read the article

• Ubuntu won't load, freezes on purple screen

  - by kara

  Last time I restarted my computer, I could not get Ubuntu to load; the screen would either go black, or would hang at the purple screen indefinitely. I have had some graphics problems in the past, but had put 'nomodeset' after 'quiet splash' in the grub command line, which at least let Ubuntu load. That doesn't work now, and doesn't work if I remove it. I looked up some answers, such as this one: Purple start screen - no splash screen However, when I enter the root in recovery mode in grub, I always get errors when I run those command lines and it won't let me modify the files. Also, if I run in recovery mode and then choose 'resume normal boot', it will continue. But instead of getting a usual interface, I get a black screen that asks for my username and password. I enter these, and it tells me I'm in Ubuntu 12.04, but I'm still on a black screen with texts. It also informs me that there are updates to install. When I use the command 'sudo apt-get update', it starts to retrieve the information, but then the screen goes blank after a couple of seconds and I can't do anything anymore. Any ideas?

  Read the article

• wireless is disabled by hardware lenovo 3000g430

  - by sudheer

  sir i have problem with my wifi switch sir please tell me solution for my problem (wifi is disabled by hardware). output of sudo lshw -C network is sudo] password for sudheer: *-network DISABLED description: Wireless interface product: BCM4312 802.11b/g LP-PHY vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:06:00.0 logical name: eth2 version: 01 serial: 00:21:00:72:3a:93 width: 64 bits clock: 33MHz capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless configuration: broadcast=yes driver=wl0 driverversion=5.100.82.38 latency=0 multicast=yes wireless=IEEE 802.11bg resources: irq:19 memory:f4700000-f4703fff *-network description: Ethernet interface product: NetLink BCM5906M Fast Ethernet PCI Express vendor: Broadcom Corporation physical id: 0 bus info: pci@0000:07:00.0 logical name: eth0 version: 02 serial: 00:1e:68:ad:24:0b size: 100Mbit/s capacity: 100Mbit/s width: 64 bits clock: 33MHz capabilities: pm vpd msi pciexpress bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd autonegotiation configuration: autonegotiation=on broadcast=yes driver=tg3 driverversion=3.121 duplex=full firmware=sb v3.04 ip=172.16.52.79 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s resources: irq:47 memory:f4600000-f460ffff output of iwconfig is lo no wireless extensions. eth2 IEEE 802.11 Access Point: Not-Associated Link Quality:5 Signal level:0 Noise level:0 Rx invalid nwid:0 invalid crypt:0 invalid misc:0 eth0 no wireless extensions. sudheer@sudheer:~$ sudo iwlistscanning sudo: iwlistscanning: command not found ***sudheer@sudheer:~$ sudo iwlist scanning*** lo Interface doesn't support scanning. eth2 Failed to read scan data : Invalid argument eth0 Interface doesn't support scanning.

  Read the article

• Dual booted Windows 7 freezes after login screen

  - by Cathal

  First-time Linux user, using a Packard Bell Easy Note TS laptop. My problem arose after I dual boot installed Ubuntu 12.04 on Windows 7 via WUBI. I backed up all my data, and reinstalled Windows from factory settings on the recovery partition. When I first tried to install Ubuntu I mistakenly closed the lid at the start of the installation, stopping it. After that I rebooted, and my second installation attempt went without a hitch. Ubuntu works perfectly, the data on the partitions seem to be fine. My problem is I can't log back in to Windows 7. After selecting it in GRUB, and then in the Windows 7/ WUBI choice on boot, it loads up perfectly til the user log in screen. After the password is inputted, it stalls on the "Welcome" busy screen. This happens in Safe mode as well. Startup repair can't find a problem and neither can CHKDSK. System restore and Last known good config have no effect either. If anyone could help me out, I'd be real grateful. edit in response to the question below, since I don't know how to comment: Windows was installed first and its partitions are the first on the list. Should I move the windows partitions to after the Linux ones on the disk? Thanks for your help.

  Read the article

• Ubuntu won't start - blank screen with flashing white cursor

  - by loomy

  My laptop is dual-booted with Windows 8 on one partition and Ubuntu 12.04.3 on the other. I've searched for my issue already, but nothing I've found so far has solved the problem. Since last week, when I try to boot Ubuntu from GRUB, I am taken to a purple screen (as usual), but then to a black screen with a blinking white _ cursor. I've tried leaving it, but nothing else happens. When I hold Shift and edit the GRUB entry to change 'quiet slash' to 'text', the back screen instead asks for my login and password. When I put them in, it tells me the date of my last logon, and then waits for further commands. Being very very new to Ubuntu, I have no idea at all what to try out at this point. I tried to launch FailsafeX, but while that was beginning, it said "unable to run server /usr/bin/x" No such file or directory", then shortly after returned to the recovery mode menu. Pressing Ctrl+Alt+Delete goes through an Ubuntu loading screen, then the laptop then restarts. Any suggestions will be very appreciated, and apologies if this is a common issue that has been answered a million times before.

  Read the article

• Ubuntu won't log in after update

  - by Dave M G

  I just updated Ubuntu about 15 minutes ago on my desktop which is running 12.04. Within the set of updates, there were some kernel upgrades. It didn't say I needed to reboot after the update was finished, but I thought I would anyway. The computer successfully rebooted up to the login screen. However, after entering my password, the screen goes black for a moment, then it comes back to the login screen. I tried the suggestions in this question, but unfortunately they didn't help. In the accepted answer, the questioner vaguely says it was a "Unity problem". I'm using Gnome-classic with full Compiz effects. I tried uninstalling and reinstalling Compiz, but that didn't fix anything. So... I can't use my desktop computer until this is fixed. I hope there is some help soon. I've uploaded the output of cat /var/log/Xorg.0.log to Pastebin. A temporary solution of changing to gdm instead of lightdm was found with help in the chat room.

  Read the article

• Are Windows partitions gone?

  - by Gigili

  I had Windows 7 on my laptop (factory setting), because of some performance issues, I decided to use recovery options to restore it to its factory condition but I don't know what has happened or what I have done that the whole operating system was gone after playing around with recovery options from the boot menu. I couldn't find Windows, so I installed Ubuntu 11.04 on my laptop. Last time I had Ubuntu on it, it was not really compatible with laptop's configuration and I had a bit of problems trying to do normal tasks I used to do on Windows. Now I want to make sure that Windows and its drivers are gone so that I can try to install a newer version of Ubuntu or Windows. I tried the command sudo fdisk -l And the result shown was: myaccount@myaccount-VPCS116FG:~$ sudo fdisk -l [sudo] password for myaccount: Disk /dev/sda: 320.1 GB, 320072933376 bytes 255 heads, 63 sectors/track, 38913 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00025b5f Device Boot Start End Blocks Id System /dev/sda1 * 1 38409 308515840 83 Linux /dev/sda2 38409 38914 4052993 5 Extended /dev/sda5 38409 38914 4052992 82 Linux swap / Solaris Disk /dev/dm-0: 4150 MB, 4150263808 bytes 255 heads, 63 sectors/track, 504 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0xa668cfe8 Disk /dev/dm-0 doesn't contain a valid partition table Is it gone? If not, what command should I try to have access to Windows partitions? Thank you.

  Read the article

• eSTEP TechCast - December 2012

  - by uwes

  Dear partner, we are pleased to announce our next eSTEP TechCast on Thursday 6th of December and would be happy if you could join. Please see below the details for the next TechCast.Date and time:Thursday, 06. December 2012, 11:00 - 12:00 GMT (12:00 - 13:00 CET; 15:00 - 16:00 GST) Title: Innovations with Oracle Solaris Cluster 4 Abstract:Oracle Solaris Cluster 4.0 is the version of Solaris Cluster that runs with Oracle Solaris 11. In this webcast we will focus at the integration of the cluster software with the IPS packaging system of Solaris 11, which makes installing and updating the software much easier and much more reliable, especially with virtualization technologies involved. Our webcast will also reflect new versions of Oracle Solaris Cluster if they will be announced in the meantime. Target audience: Tech Presales Speaker: Hartmut Streppel Call Info:Call-in-toll-free number: 08006948154 (United Kingdom)Call-in-toll-free number: +44-2081181001 (United Kingdom) Show global numbers Conference Code: 803 594 3Security Passcode: 9876Webex Info (Oracle Web Conference) Meeting Number: 255 760 510Meeting Password: tech2011 Playback / Recording / Archive: The webcasts will be recorded and will be available shortly after the event in the eSTEP portal under the Events tab, where you could find also material from already delivered eSTEP TechCasts. Use your email-adress and PIN: eSTEP_2011 to get access. Feel free to have a look. We are happy to get your comments and feedback. Thanks and best regards, Partner HW Enablement EMEA

  Read the article

• How to Install WebLogic 12c ZIP on Linux

  - by Bruno.Borges

  I knew that WebLogic had this small ZIP distribution, of only 184M, but what I didn't know was that it is so easy to install it on Linux machines, specially for development purposes, that I thought I had to blog about it. You may want to check this blog, where I found the missing part on this how to, but I'm blogging this again because I wanted to put it in a simpler way, straight to the point. And if you are looking for a how to for Mac, check Arun Gupta's post.  So, here's the step-by-step: 1 - Download the ZIP distribution (don't worry if your system is x86_64)Don't forget to accept the OTN Free Developer License Agreement! 2 - Choose where to install your WebLogic server and your domain, and set as your MW_HOME environment variableI will use /opt/middleware/weblogic for this how to export MW_HOME=/opt/middleware/weblogicMake sure this path exists in your system. 'mydomains' will be used to keep your WebLogic domain. mkdir -p $MW_HOME/mydomain 3 - If you don't have your JAVA_HOME environment variable still configured, do it. Point it to where your JDK is installed. export JAVA_HOME=/usr/lib/jvm/default-java 4 - Unzip the downloaded file into MW_HOME unzip wls1211_dev.zip -d $MW_HOME 5 - Go to that directory and run configure.sh cd $MW_HOME ./configure.sh 6 - Call the setEnvs.sh script . $MW_HOME/wlserver/server/bin/setWLSEnv.sh7 - Create your development domain. It will ask you for username and password. I like to use weblogic / welcome1cd $MW_HOME/mydomain $JAVA_HOME/bin/java $JAVA_OPTIONS -Xmx1024m \ -Dweblogic.management.allowPasswordEcho=true weblogic.Server8 - Start WebLogic and access its web console(sh startWebLogic.sh &); sleep 10; firefox http://localhost:7001/consoleUsually, it takes only 10 seconds to start a domain, and 5 more to deploy the Administration Console (on my laptop). :-)Enjoy!

  Read the article

• sudoers - simple explanation requested

  - by Redsandro

  Everytime I want to be able to run something that requires me to be a sudoer too many times, I need to google for the formatting of /etc/sudoers to remind me again what exactly is the proper way to write it. Now I see different writing styles in my sudoers file, which is the consequence of different google results over the months. I've also noticed that the second example (below) seems to work in XFCE, but not in Cinnamon (Gnome 3). This could be totally unrelated, but nontheless I'd like to know once and for all, what is the correct grammar of the sudoer line, and what is the difference between the given examples? redsandro ALL=NOPASSWD:/path/to/command redsandro ALL=(ALL) NOPASSWD:/path/to/command redsandro ALL=(ALL:ALL) NOPASSWD:/path/to/command Also, what are all the ALL's for? One user, one command, yet I need to use the ALL keyword up to three times? Am I doing this wrong? Of course, omitting NOPASSWD: makes you enter your password before you are permitted to run the command, but one point of confusion is the usage of = and :, for the final command that is the subject of the line can be prepended by either =, :, , or ), confusing grammar for similar semantics.

  Read the article

• AppleTV - itunes store is temporarily unavailable - please check back later

  - by Ken

  When attempting to rent a movie on ATV, my wife received the error message above.  Alternately “server unavailable”.  When your wife is sick, the amount of IT support she needs goes up exponentially.  One piece of the puzzle was that she had changed her Apple ID password.  On her PC I ran iTunes and under account, there was only 1 device listed (not the ATV).  Even when signed out/back-in on the ATV under Settings>iTunes it still gave same error message.  What I suspect is it thinks she is trying to authorize the device to another Apple ID.  Some new 90 day rule limits when a device can be associated with another Apple ID.  Your iTunes store/account will show devices, and how long before they can be associated with a different Apple ID from the Account Information page in iTunes on your computer.  Apple must have no freaking idea why someone would want to know which ID is associated to the ATV (i.e. the vice versa), because it can’t be done. Solution: Try ATV settings>reset I swapped out ATV 1 for ATV 2 (used for music streaming downstairs).  I know it’s a cop-out solution, but remember I had a sick wife breathing down my neck.

  Read the article

• Incompleted ubuntu 12.04 install dual-boot xp

  - by Mike

  This weekend has been the 1st time i've tried to install ubuntu. On the initial install, (I am using a USB) the installation went all the way through and asked to restart when completed. I was not able to get grub to boot and kept going through windows. After some research I found some articles on updating/reinstalling grub, so I followed those. I finally got grub to load after a day but there was no windows option only the Ubuntu 12.04 which when I selected it only gave me a fatal error 17. I booted from the usb again and deleted the partitions and installed again. This time I got an error 15. I then booted through xp and downloaded the WUBI.exe and uninstalled ubuntu and reinstalled again. The installation went to the very end and then gave an error message (which I don't remember exactly what it said) something along the lines of checking my logs on my C drive. I then uninstalled ubuntu and removed the wubi.exe file and wiped my usb and did the download to the usb again. Booted through usb and ran the install process again. It again went through the install process but after creating username and password and hitting continue the installation dialogue box disappears and the mouse spinning wheel is displayed but I do not receive the prompt to restart. I can still access the side menu for ubuntu but the wheel keeps spinning. How to I get Ubuntu to install properly

  Read the article

• How to integrate a PHP CMS with paypal so that only users who completed a payment can register and authenticate?

  - by ibiza

  I am currently using a PHP CMS - cmsmadesimple - in order to create a website where services will be sold. I intend to use Paypal 'Buy Now' buttons in order to offer a few packages that will be renewable every 1-month or every 3-months and that grant access to the secure content of the website for a given period of time. Everything is going well so far but I am somewhat at loss for the user registration process as I have a few constraints I would like to use and it would be nice to automate the process if possible. Here are the constraints : User should be able to register to my website and choose a password himself Only users that paid should be able to register Access permissions should be disabled automatically after the service period if the package is not renewed And here is the process which I am thinking of : User clicks 'buy' on my website User is redirected on Paypal and completes the payment The paypal email used to pay should be returned to my server and somehow stored If it is a new email, user needs to register to my website (else if it is a returning customer, the deactivation flag for payment stopped should be removed to give back access) If a user does not renew his subscription, there should be a deactivation flag automatically set to the email used in order to lock access until next payment. Ideally, no human intervention is needed. What is the best way to implement all this? I am a bit at loss. I found this article that explained a few things and even has a nice code snippet, except that I'm not sure where to plug it. Thanks all

  Read the article

• SteamCMD can't add files to my home directory

  - by Angle O'Saxon

  I'm trying to clean up the administration of some game servers I run on a Ubuntu box, part of which has been finally setting permissions properly so I can run the Steam console tool that controls updates and such. I had been running it as root using sudo, but I changed the permissions so that I can start it as a regular user rather than root. That bit seems to work fine, but now when SteamCMD actually starts, it errors with the following output ./steam.sh: line 24: /home/angleosaxon/.steampid: Permission denied Installing breakpad exception handler for appid(steam)/version(1334262703) SteamUpdater: Error: Couldn't create directory /home/angleosaxon/Steam/package, got error 13 [ 0%] Download complete. [----] Verifying installation... unlinked 0 orphaned pipes [----] !!! Fatal Error: Steam failed to load: *SteamStartEngine(0xbfa7cfa0) failed with error 1: Failed to open logfile /home/angleosaxon/Steam/steam.log Leaving aside the question of why it wants to add this information to my home directory, why is it getting access denied errors? As I understand it, since it's being run by my account, it operates with my permissions, so it should be able to read/write from my home directory, shouldn't it? This is the command I'm using to run it: /opt/steamcmd/steam.sh "+login UserAccount \"This is not my actual password.\"" +force_install_dir $ServerDir "+app_update 215360 validate" +quit

  Read the article

• how do I fix ati driver issue

  - by Michael

  I have little knowledge about ubuntu, but I am learning. Recently, my ubuntu 12.04 required that I update. I noticed that it was updating xorg and other things, after the update I was asked to reboot. I did. now when I start that computer up, it cannot detect any display and refuses to boot from usb. I have no idea how to recover my computer. It simply starts in what is akin to the terminal program and ask for my username and password. After that, I can enter commands. The problem may be because I manually installed drivers by copy pasting from some instructional that I now have no idea where they are, but what it amounts to is that I "built" the drivers. They were working GREAT until this update. I did this because otherwise I was unable to have sound through my hdmi. After I hand built the drivers, they worked great. After this update Ka-blam! nothing... Also, I had okay-ed lots of update sources (though all of them [xorg and such] were the stable versions, not the unstable update sources) Please help and thank you in advance. (if this is posted incorrectly or misplace, please let me know what to do)

  Read the article

< Previous Page | 365 366 367 368 369 370 371 372 373 374 375 376  | Next Page >