Search Results

Search found 14924 results on 597 pages for 'kernel mode'.

Page 373/597 | < Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >

• "Request not supported" in IPCONFIG (WinXP SP3)

  - by pablog

  In a customer PC (Windows XP SP3), suddenly the network went down: the network adapter appears with an error mark. I replaced the network card, but the new one does the same thing. When I enter IPCONFIG, XP shows this error (in standard and safe mode): Internal error occurred Request not supported Unable to query host name If I start the system with a boot cd the PC runs fine, so the problem seems to be in the XP installation. I tried: uninstalling and reinstalling the network card in the Device Manager disabling and reenabling the card netsh int ip reset netsh winsock reset catalog and a couple of "reset" programs (WinsockxpFix.exe, etc) with no luck. Is there any way to fix it without reinstalling XP? TIA, Pablo

  Read the article

• Is span monitoring on Cisco ASA 5520 possible?

  - by Brent

  From what I have read, you can use the switchport monitor command on ASA 5505's to setup a Span port due to the back of the ASA actually being a switch. On my 5520, I do not see the switchport command listed when issuing a ? via the CLI. How do people monitor traffic on non-5505's? My goal is to connect our IDS/IPS device that is running is promiscuous mode to a Ethernet port on the 5520 to monitor WAN traffic. I do not want to have to pass the WAN traffic through a switch as it would require me to get two (for redundancy) STP/switchport capable switches. Guide to setting up switchport access on a 5505: http://www.wr-mem.com/?p=66

  Read the article

• Is it possible to use the MMM tool without virtual IP capability?

  - by Artem

  We are on a host (Serverbeach) that does not support Virtual/floating IPs until you reserve at least a half-rack, which is just a little more than we are willing to spend per month right now. We do have 2 machines in one of their datacenters, and I am using these 2 machines right now in the Master-Master in Active-Passive Mode just like done by MMM -- http://mysql-mmm.org/. I have just set them up and I managing them manually, with manual switch on the Web frontend to tell it to connect to the correct (active) master. Is there any way to use MMM without virtual IPs? Any other comments on this setup?

  Read the article

• WinXP keyboard input repeat rate problem

  - by Victor Sorokin

  I have problem similar to http://superuser.com/questions/33981/problems-with-kvm-switch-and-keyboard-repeat-rate-on-windows-xp: When I press and hold some key it's repeated random number of times, after that repeat stops and I need to release key and press it again to make repeat continue. If there's simultaneous sound playback and repeat is stopped, sound's stuck while I hold key with unpleasant drumming as if there's some audio problem. This issue is reproducible in WinXP Safe Mode. On the same config under Linux there's no issue. My config: List item PS/2 Logitech Keyboard USB Mouse MB M3A/H-HDMI WinXP Pro English SP2 with added Russian layout (WinXP loads via GRUB2) Realtek audio drivers for AC97 Thanks for your suggestions J

  Read the article

• How to use Ralink RT2501/RT2573 as wifi access point in Debian Linux

  - by user60813

  Hi, I have a fit-PC server with Debian GNU/Linux (Lenny). I would like to use it as a wifi access point since my Linksys WRT54GS has become unstable. I have a USB Ralink wifi NIC. When I insert the card to USB I can see this with lsusb: Bus 001 Device 002: ID 148f:2573 Ralink Technology, Corp. RT2501/RT2573 Wireless Adapter I have tried following various HOWTOs on using wifi card as AP in Linux, however, it seems that the card cannot go into monitor mode. I believe this is because I must use a newer driver or upload non-free firmware or something like that. I have tried installed wicd, but it does not help. I bought this wifi adapter because I was told that it is one of the most common used Linux supported wifi cards that can be used as access point and a lot of other stuff. So my question is: How do I set up this USB wifi card as wireless access point in Debian Lenny?

  Read the article

• bluetooth doesn't turn off during sleep in Windows 7

  - by lajos

  I have a Bluetooth USB dongle on a Windows 7 laptop. I did not install any Bluetooth drivers, so I assume that the device is using the Microsoft stack. When the computer goes to sleep, the Bluetooth adapter stays on. I don't want Bluetooth devices to wake the computer, so I want sleep to turn off the dongle, but I can't find power management options for Bluetooth in the Control Panel and Device Manager. I also have an issue where the computer doesn't reach full sleep mode, I'm hoping that turning Bluetooth off will solve that problem, too. How can I turn off Bluetooth during sleep?

  Read the article

• Getting Correct Edition of Office 2007 from Serial Key

  - by Lloyd Sparkes

  I have been asked by a Client to refresh one of their Machines. To do this i managed to get Windows XP Setup to run in Repair mode, and while in setup i ran a serial key grabber, which grabbed the key for Office 2007 The only thing is that the key grabber didnt tell me what edition of Office 2007 was installed. I have aqquired a number of ISO's for the different editions (Home & Student, Standard, Professional, Ultimate) but the key doesnt work in any of them. Is there a way to get the edition from the Serial Key, or is there a generic ISO that will install any edition depending on the Serial Key?

  Read the article

• Carbonite Restore Error after Windows Update

  - by Rev

  I recently installed Windows 8 on my main machine, and I'm have an issue with Carbonite. I can't restore any files from my previous OS, only files that where backed up from the current OS. I can download them from the web service, but I can't restore them with the client. The error says "You don't have the necessary security permissions to restore this file." (The file on top was backed up from the new install, while the one on bottom was from the old install.) I'm also having another issue, where Carbonite doesn't think it's running in admin mode. I think it's probably related to this error. When I right click to restore a file, I can't choose a location to restore to. I contacted Carbonite, and they said it's a known issue that apparently happens when upgrade from XP to 7, but they wouldn't help me since I'm running a beta OS. Hopefully one of you fine folks will have an idea.

  Read the article

• SPAN/Port mirroring on Linksys switch

  - by Bastien974

  Hi all, I'm trying to deploy a Snort box in my LAN. I have a Linksys SRW248G4 and trying to configure Port mirroring so that Snort can listen everything on the network in promiscuous mode. So in ADMIN / Port Mirroring, I have 3 things: Source Port (e1,...e48, g1...g4) Type (Rx, Tx, Both) Target (e1...e48, g1...g4) Last time I played with it, I killed all traffic on the switch, I had to reboot it several times... so now I'm asking question before: Do I need to configure each Source Port (from 1 to 48) to forward to the single promiscuous port ? 48 rules !? Is that correct ? Thanks !

  Read the article

• SCO UNIX problem: "Cannot create /var/adm/utmp or /var/adm/utmpx"

  - by Maktouch

  Hey everyone, I have an old server that doesn't boot. I don't know the version of unix installed, but I see SCO UNIX. It stops with that error: UX:init: ERROR: Cannot create /var/adm/utmp or /var/adm/utmpx UX:init: ERROR: failed write of utmpx entry: " " UX:init: ERROR: failed write of utmpx entry: " " UX:init: INFO: SINGLE USER MODE After that message, it just stops. I cannot write or press anything. Even CTRL + ALT + DEL does not work. I cannot get into the system. I have tried booting with a DamnSmallLinux LiveCD but it does not recognize the file system on HDA. Is there a way to either log in as root or bypass this error? Thanks.

  Read the article

• fast opening and closing connection with a specific port

  - by michale

  We have a Main application named "Trevor" installed in 2008R2 machine named "TEAMER12" which is slow now. One more application named "TVS" also running in and found there were many connections per second occurring to port 5009. netstat tool mentions that some fast connection open/close seen for port 5009 So first it will be listening mode like shown below TCP 0.0.0.0:5009 TEAMER12:0 LISTENING then establishes connection like TCP 127.0.0.1:5009 TEAMER12:49519 ESTABLISHED TCP 127.0.0.1:5009 TEAMER12:60903 ESTABLISHED After that iwill become TIME_WAIT and i could see several entries like shown below TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT after that it will establish connection like TCP 127.0.0.1:60903 TEAMER12:5009 ESTABLISHED TCP 127.0.0.1:64181 TEAMER12:microsoft-ds ESTABLISHED again it will go several entries like TIME_WAIT TCP 127.0.0.1:49156 TEAMER12:5009 TIME_WAIT Finally it will establish like this TCP 172.26.127.40:139 TEAMER12:0 LISTENING TCP 172.26.127.42:139 TEAMER12:0 LISTENING TCP 172.26.127.42:5009 TEAMER12:64445 ESTABLISHED TCP 172.26.127.42:64445 TEAMER12:5009 ESTABLISHED Can any body tell me whats the reason behind why many connections per second occurring to port 5009 and why application slow?

  Read the article

• HAProxy NGInx SSL setup

  - by Niclas

  I've been looking around different setups for a server cluster supporting SSL and I would like to benchmark my idea with you. Requirements: All servers in the cluster should be under the same full domain name. (http and https) Routing to subsystems is done on URI matching in HA proxy. All URIs have support for SSL support. Wish: Centralizing routing rules ---<----http-----<-- | | Inet -->HA--+---https--->NGInx_SSL_1..N | | +---http---> Apache_1..M | +---http---> NodeJS Idea: Configure HA to route all SSL traffic (mode=tcp,algorithm=Source) to an NGInx cluster turning https traffic into http. Re-pass the http traffic from NGInx to the HA for normal load-balancing which performs load balancing based on HA config. My question is simply: Is this the best way to to configure based on requirements above?

  Read the article

• ESXi boot time with 9 iSCSI targets

  - by Myles Gray

  Our ESXi hosts have always been slow booting when it came to iscsi_vmk loaded successfully - sitting here for almost 5 minutes. In all a full server reboot takes almost 12 minutes. We have 9 iSCSI targets per host (5 SANs with redundant interfaces) configured as dynamic discovery targets. Has anyone experienced this? Can it be remedied with static discovery mode? Are there any debug steps we can work through to help diagnose this? (All our targets are accessible at boot so i'm assuming the host isn't stuck retrying to connect to a target)

  Read the article

• How to view bad blocks on mounted ext3 filesystem?

  - by Basilevs

  I've ran fsck -c on the (unmounted) partition in question a while ago. The process was unattended and results were not stored anywhere (except badblock inode). Now I'd like to get badblock information to know if there are any problems with the harddrive. Unfortunately, partition is used in the production system and can't be unmounted. I see two ways to get what I want: Run badblocks in read-only mode. This will probably take a lot of time and cause unnecessary bruden on the system. Somehow extract information about badblocks from the filesystem iteself. How can I view known badblocks registered in mounted filesystem?

  Read the article

• Software for formatting / web-publishing tutorial-type, technical articles

  - by gojira

  I want to put some of my own technical writing on the web: tutorials, how-to's, conceptual articles about programming etc. I write mostly for myself yet, but think others can benefit from it so I want to put it online, and I also have plans of making everything more coherent and turning it into a book. My articles are not meant as a blog, they're just meant as a collection of tutorials and how-to's, but I think a blog-type software would probably be the most appropriate mode of formatting that kind of stuff. Right now I am using the blog feature of cite u like, which is very low tech and I really need something better. On my wish list is, among other things: code snippets in scrollable boxes syntax highlighting for source code snippets tagging articles with graphical icons according to topic, like in slashdot of course users (i.e. readers) should be able to comment on articles Also, just more options than a super-simple blog should look slick! should not look wikipedia-like Is there any software you can recommend for this purpose?

  Read the article

• Custom firmware for Asus WL-520g

  - by Jaroslav Záruba

  What custom firmware works with Asus WL-520g? (Note this is not 520gU, 520gC, etc.) I failed to flash it with Tomato (Tomato_1_28_ND.zip) - the admin UI does not accept the file, and when trying to tftp the file as adviced for 520gU all I get is this: Transfering file tomato-ND.trx to server in octet mode... Error occurred during the file transfer (Error code = 0): Error in SendPacket() call. I just saved the router form rather unsuccessful flash to DD-WRT (after few hours the router fell into coma), and I'd like to keep it as a backup should the new one die or whatever. (Unfortunately the stock firmware does not support WOL.)

  Read the article

• How to share a VPN connection in a VMWare Guest VM with the Host

  - by Jonathan

  The need - This question is relevant for all of those who want to bypass their corporate's annoying VPN, and access their work/corporate network from their private computer, especially if the corporate VPN client software can't run on their private computer. Homework: this question is very similar to this one and this one, which aren't answered :( The challange - Can't run the corporate VPN client from the private computer, so converted the work laptop to a VMWare Virtual Machine. The VPN client is working fine inside the Guest VM, now we want to share it with the Host (the private computer) The specs: * The private computer (Host OS) is Mac OS X Lion 64bit * The corporate laptop (Guest VM) is WinXP 32bit, running in Bridged network mode * The VPN client on the Guest VM is is Checkpoint SecuRemote NGX R60 HFA03 * While the VPN is running in the Guest VM, the Host can still ping the Guest and vice versa

  Read the article

• Where is the encfs volume key stored?

  - by Waldorf

  I am trying to use encfs in reverse mode. I understand that the passphase is used to encrypt a key which is then stored encrypted into the encfs6.xml file. What I do not understand is the following. Create en encrypted virtual fs of a folder by using passphrase A unmount this folder. Delete all contents including the encfs6.xml file If you then try to do the same with another passphrse I would expect that a new encfs6.xml would be created. However I get the following error message: "Error decoding volume key, password incorrect" So I wonder, what volume key is incorrect, I thought it was in the encfs6.xml file ?

  Read the article

• Weird problem, special characters coming after formatting the hard drive, computer isn't starting 0_

  - by m3taspl0it

  Hya friends , Last night my computer was working fine. But today when i came back from college and started it , it was starting fine but after sometime it's getting restarted , again and again getting restarted at different points , so i tried to boot it in safe mode but same problem. Now after all this , i finally decided to format the drive C (it is in 80 GB) and load new OS windows XP3. After formatting (quick format) and loading xp3 sufficient files , when it was getting rebooted for copying the actual os files , it hung and a weird screen came. I've also attached the pic of error : http://www.postimage.org/image.php?v=gxz1vKS My specs : P4 3.0 Ghz 2 GB RAM (2x 512 mb and 1 GB) 3 hard drives { 80 GB (5 years old around) 320 GB ( 2 years old around) 500 GB ( recently bought) 256 MB graphics card any help is very appreciated , thanks

  Read the article

• Re-assembling the RAID-5 array reboots my CentOS-5 machine

  - by xraminx

  I have 3 HDD's, each divided into 3 partitions. I had created a RAID-1 for boot partition md0 created from sda0, sdb0 and had also created two RAID-5 arrays: md1 created from sda1, sdb1, sdc1 md2 created from sda2, sdb2, sdc2 It used to work fine but one day I had to power off the machine (cold reboot) to get any response from the machine. After that, when the system started booting, it tried for a while to reconstruct the RAID arrays but after a few minutes it crashed silently. I booted the system in linux rescue mode from the DVD and tried to re-assemble the RAID devices manually. I was able to re-assemble md0 and md1 using: mdadm --assemble --scan /dev/md0 mdadm --assemble --scan /dev/md1 But when I try to re-assemble md2 using: mdadm --assemble --scan /dev/md2 the system reboots silently again. How can I fix this problem?

  Read the article

• Wrong Sound Blaster's PCI ID within Windows

  - by pavian

  I own Sound Blaster X-Fi Titanium, it was working with no problems under Linux or Windows 7. It's original PCI ID is 1102:000b but now I see different within MS Windows. BIOS setup: 1102:000b GNU/Linux: 1102:000b Windows 7: 1102:000d Windows 8: 1102:000d In last days I'm experimenting with IOMMU PCI passthrough in Xen and I tried to pass this device to virtual Windows 7 and 8. Here I found this problem. I don't know if this is just coincidence or reason of my problem but it's wrong even in physical system. Windows detects 1102:000d as a High Definition Audio sound device (I guess this name, I have localized Windows, but this is general name, the same was with Realtek HDA before drivers), it's playing but it's unstable (Windows speaker testing can crash that application) and I can't install Creative software. Used driver is hdaudio.sys. Booting in BIOS or UEFI mode doesn't change anything. Nor CMOS clean. Someone met the same problem.

  Read the article

• Recover backup copy of a ubuntu linux installation on a usb stick using dd

  - by user10826

  Hi, I installed Ubuntu 10.04 on a usb stick in persistent install mode. So I could boot the laptop or my desktop computer with the stick, at boot time. Once I needed the 8GB stick for another purposes so I thought about coyping it to my desktop doing from mac os x: dd if=/dev/disks3s of=/Users/jack/Desktop/usb_copy Now I am trying to do the opposite, after having used the stick, which was formatted to NTFS, just doing dd if=/Users/jack/Desktop/usb_copy of=/dev/disks3s but although I can see that almost of the files are there, I can not boot again. IT is also strange the the file permissions are kind of strange, something like _user What can I do ? Thanks

  Read the article

• Recover backup copy of a ubuntu linux installation on a usb stick using dd

  - by user10826

  Hi, I installed Ubuntu 10.04 on a usb stick in persistent install mode. So I could boot the laptop or my desktop computer with the stick, at boot time. Once I needed the 8GB stick for another purposes so I thought about coyping it to my desktop doing from mac os x: dd if=/dev/disks3s of=/Users/jack/Desktop/usb_copy Now I am trying to do the opposite, after having used the stick, which was formatted to NTFS, just doing dd if=/Users/jack/Desktop/usb_copy of=/dev/disks3s but although I can see that almost of the files are there, I can not boot again. IT is also strange the the file permissions are kind of strange, something like _user What can I do ? Thanks

  Read the article

• Suppress EXT3-fs warning on mount

  - by STM

  I am familiar with output suppress on Unix machines, ie: cat /file/that/doesnt/exist > /dev/null 2>& However I can't seem to suppress the output of mount when an ext3 filesystem is mounted for the nth time, and it recommends an fsck. As it happens, fscks are run regularly by another machine, so these warning messages are needlessly interrupting the flow of output to my pretty bash script. These are the errors: # mount -t ext3 /dev/sda1 /mnt > /dev/null 2>& kjournald starting. Commit interval 5 seconds EXT3-fs warning: maximal mount count reached, running e2fsck is recommended EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal EXT3-fs: mounted filesystem with ordered data mode. Can anyone shed some light on this? I'm clearly blocking both fd's, but somehow output is still getting through. This is GNU Bash v2.05a

  Read the article

• can I force server to always use turboboost?

  - by javapowered

  I'm using HP DL360p Gen8 with 2 * Xeon E5-2640. I do not load CPU 100%, i load it only ~10% and so I guess turboboost is not activated. However I'm using my server for trading so I absolutely don't care about CPU loading but I always want to process my data asap. So I want server to operate using maximum 3 GHz. I.e. 90% of CPU time I don't have anything to process. 10% of CPU time I have data to process. But I need to process it ASAP. I need every single microsecond. So I want server to operate always at maximum "turboboosted" mode. Is it possible?

  Read the article

< Previous Page | 369 370 371 372 373 374 375 376 377 378 379 380  | Next Page >