Search Results

Search found 30511 results on 1221 pages for 'linux networking'.

Page 374/1221 | < Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >

• Can't access certain web sites - reset router, any ideas?

  - by IniTech

  EDIT: This problem was resolved by my ISP - had to do with damaged fiber in one of their locations. Thanks to everyone that helped. Not sure if this is the right site (I'm a StackOverflow user) so I thought I'd give it a shot. I'm having trouble connecting to certain sites on any of the 3 machines that are on my LAN. The following sites are returning "Problem Loading Page - The connection has timed out" Sourceforge.net CNet.com Microsoft.com OpenDNS.com even my company's webiste I was worried about possible malware/virus, but I don't think that is the case (given the inability to access my company's site and the fact that all 3 machines are having the same issues.) I've tried with IE8, FF, and Chrome I have reset my router (WRT54G) and my machine(s) multiple times. EDIT: It is also worth noting that this page spins constantly and no avatars show up (I'm assuming it is trying to access gravatar.com with no success.) EDIT: I have the same issues directly connected to the modem. So, any router config is probably not the issue I'm a programmer, not a network guy - any ideas?

  Read the article

• Streaming a large file

  - by Rich

  quick question say i wanted to download a file of considerable size 10gb say and i sent the GET request to a web server to download that file question is, if the client stopped reading the TCP connection, would the entire file still be downloaded, or does it depend on the client sending back an ack or something to the circuit asking for the next packet hope that makes sense This question was originally asked involving the Tor network, but i just want to know how a standard internet connection would handle this Thanks

  Read the article

• Extremely poor WiFi reception on new desktop

  - by guy

  I just received a new desktop with a built-in WiFi card (Windows 7 Home Premium x64). However, I am only able to receive any WiFi signal when the computer is within 1-2 meters of a router. Even then, the signal is very weak (Windows 7 says it is "poor"). I have tried this with 2 different routers and see similar results. I have somewhere around a dozen other devices that can connect to both routers with greater signal strength (usually full strength) from much, much further away. When I tried calling support I was instructed to reinstall my drivers and attempt to change the WiFi channel of the router. Neither worked. I was then told that the problem was with my routers and that the computer was functioning normally and that it was certainly not a hardware problem. What would be the cause of this and is there anything I can do to fix it?

  Read the article

• Window 7 image in vmware will allow network connection out but not http

  - by Ormis

  I am currently trying to create a set of images to deploy on my network, but I've run in to a snag. When I create my own Windows 7 image I can successfully use NAT for connecting to the network but whenever I try to access a webpage I get nothing. To be more specific, All firewalls/iptables are disabled on my host machine, my virtual machine, and my network. I can do lookups and all addresses respond correctly (i'm even using Google's DNS). On the host OS i have full connectivity. On the virtual machine I can ping any device I want and all addresses resolve correctly. Within a browser I cannot reach any page via hostname or IP. I feel almost like port 80 is being blocked but i can't find any reason this would be the case. If anyone has had this occur before, I would love some insight to the problem. I initially asked this on stackoverflow and now my eyes are now opened up to superuser. Thank you for any help you can provide.

  Read the article

• Remotely port forward/launch process or a client-less remote desktop app?

  - by DC177E

  I have an XP box running Logmein at a remote location behind a linksys router, which was running well for a whole of four days, until we had a power failure. Our ISP gave us a new IP, the machine restarted, and logmein did not autorun (or, at least, it did not automatically sign in), and our service (which may or may not be a Minecraft server with non-backed-up save files) also did not run upon startup. Logmein does not register the new IP (it still displays the old one). I have a DDNS updater service, so I do know the new dynamic address. I have tried using the built in XP remote desktop service, but, as with almost all non-cloud-based remote desktop services, it requires a port forward. Thus, I would appreciate it if anyone has any ideas as to: A: Any way of accessing our router remotely to forward the remote desktop port. I've seen the Remote Management option (forwarding the setup page to port 8080), but I do not have it enabled. I've tried UPnP, but again, the setup page for our router is not forwarded. B: Any way of remotely launching a process that does not require port forwarding (or uses ports 255XX, 18XXX, or 9000.), such as a remote console service built into XP. I realize this is a near impossibility. C: A Way to remotely start logmein, and sign in, which is likely a definite impossibility. Sorry if this is too specific for Stackexchange, or if I've put it into the wrong section (is SuperUser the correct place for this?). Ideas would, again be much appreciated, as shot-in-the-dark-like this may be.

  Read the article

• Distributing Microsoft Office Template or Macro over the network

  - by zfranciscus

  We have around 400 users who use Word and we want to make their life easier by distributing templates and macros over the network. The easiest way to do this of course to setup a shared network folder and let them get the appropriate templates and macros. Of course, each user has to know where to copy these files to in their local PC, and we have to rely on constant email communication to let them know for newer version of the macro and templates. The next alternative is to ask them to configure Word to point to these network folder. But of course any disruption to the network means disruption to their work. We are thinking to setup a synchronization mechanism that downloads new templates to their local machine. We are also thinking to make this sync tool to prompt users that it will download new templates - you know just to give them visibility that they are receiving changes. We are wondering what is the best approach that people usually use in their workplaces ? Are there any specific tool that can make this task easier ?

  Read the article

• Wireless N extend G range?

  - by Sam

  I've searched all over the internet for an answer to this and I can't find one. If I purchase a wireless N router, with greater range than my current G router will the range of the wireless G signal go as far as the wireless N signal? I say this because Wireless N routers are supposed to be compatible with wireless G devices. Is the wireless G a lesser signal coming out of the router? Sorry if I confused you, I am a little confused myself.

  Read the article

• How much does a IPtables router slow down a connection?

  - by RayQuang

  Hi, I would like to know if introducing a new gateway in my network will slow things down. The question may sound unclear but here is an illustration: Before Installing gateway server Main Router <=> switches <=> servers after installing gateway Server Main Router <=> IPtables router <=> switches <=> servers My question is. How much will this delay incoming outgoing requests / file transfers. thanks, RayQuang

  Read the article

• How to link processing power of old computers together?

  - by redIago

  Hey all, I'm sitting on 8 old computers of varied sorts that are more or less useless at this point for any other purpose really. Is there a way I could link their hardware or processing power or whatever together over wifi and use one as like a central computer? Like it would be cool to distribute the processing of some video game or encryption generating program over the collective computers. Any way to do all this? Thanks.

  Read the article

• Cisco: changing VTP mode server/client to transparent

  - by J. Smith

  I have around 40 L2 switches (2960, 3560, 3500, 3750) running in VTP client mode and one L3 switch (6500) running in VTP server mode, all connected together. I would like to switch everything in VTP transparent mode without any interruption of service. I've already test on a poc version with 3 switches (Catalyst 2950, 3560 and 3750). Using serial and SSH connection, it is seems working but i'm not sure it is enough representative compare to the real network. Knowing that the VTP Pruning is enabled, I am wondering what would be the best procedure to proceed the changement. I've read that we could lost connection by keeping it enabled. Should I change the server or clients first? Is it important to change the VTP domain and VTP Pruning parameters?

  Read the article

• 2 Computers, same network, different outgoing speeds when uploading to internet?

  - by user117339

  I have 2 work machines in my office, a PowerMac G5 and a MacBook Air. Both behind an IPCop firewall. The PowerMac is connected through a gigabit switch, the MacBook Air is connected through a Netgear 802.11g access point that is then plugged into the gigabit switch. There is also a FreeNAS box, both machines are able to read and write files to it at close to their pipe speeds. The main problem is when I am trying to upload files to the internet at large. The G5 is only hitting 0.1 - 0.25 Mbps. The Macbook is able to hit 2-3 Mbps. The setup (G5 / IPCop / Network) has been the same for 5 years. The issues with the internet speed started about 3 months ago. I hadn't tested on the Macbook at this point. I had complained to the ISP, they said their modem needed a firmware update, did that nothing changed. Reset IPCop, turned off squid, etc. No changes. The ISP switched the office over to a better plan with a theoretical 6 Mbps up, still no change. At this point I tried testing the Macbook, and lo and behold there's the speed. But why? I have tried changing out everything, cables, switches, using another ethernet port on the G5, wiping the system, using DHCP, using manual IPs, changing DNS servers, etc. Nothing works. I figured that if there was something horribly wrong with the network, then internally I would find a similar issue, but that is perfect. iperf, ping, etc show no dropped packets and near saturation of the internal network. I'm at a loss as to what the heck is going on. Any ideas would be appreciated! Below are some screenshots of speedtest.net: G5: Macbook Air:

  Read the article

• How do I install Skype on computer so that anyone who logs in does NOT have to go through the initial config?

  - by Matt

  I installed Skype when logged on to the (local) admin account. Now, when I log off that, and log on as myname on the domain, I have to click through the intial setup steps (after you've already run the installer) of Skype. So, I have to click next to get through the mic setup/test, and it asks me if I want to take a pic. How do I get it so that any person who logs in can just open Skype and go straight to the login screen? Windows 7 64 bit, 2008R2

  Read the article

• VM connected to network but not to internet in VMware Player 6 on Windows 8.1 host

  - by user1257262

  So I am running Bitnami's MEAN stack in VMware Player 6.0.2 on Windows 8.1 and the VM connects just fine to the network: https://www.dropbox.com/s/xfdzohjuuepz52w/ifconfig.PNG However, I am having a great deal of trouble getting the VM to communicate with the internet. No matter what sort of action I take (even something as simple as apt-get update), the machine just sits there and eventually fails to connect. Here is my VM's Network Adapter configuration: https://www.dropbox.com/s/xfdzohjuuepz52w/ifconfig.PNG On my host Windows 8.1 computer, I actually have the VMware Bridge Protocol enabled but for VMware Network Adapters (VMnet1 and VMnet 8), but they are listed as having No Internet access in my Network and Sharing Center. I am not entirely sure if these adapters are relevant to connecting the VM to the internet, to be honest. This is the first time I have ever had an issue connecting a virtual machine to the internet. This problem is also happening with other VM's I am trying to run. Can someone tell me what I am doing wrong and how I can fix it?

  Read the article

• Windows 7 - ICS - Xbox360

  - by Hailwood

  I am trying to connect my xbox360 to the internet through ICS using my laptop. I have done this a few days ago using the exact same hardware(so no hardware problems) The laptop can browse the internet. The laptop gets its settings though DHCP. I have enabled ICS on the Wireless connection (where the internet is coming from) I have set the xbox and the Wired connection on the laptop to obtain settings automatically. The issue is that the Wired connection only shows 'Unidentified Network'. What could i be doing wrong?

  Read the article

• Network bandwidth usage dashboard?

  - by SkippyFlipjack

  I have a couple of wifi access points hooked up to my home network, one of which I keep unsecured for some development I do; there are only a couple other homes within range and they've got their own wifi so it's not a big concern. I also have a Sonos system, Tivo, Roku, a couple laptops, a couple phones, an iPad and a desktop machine, all of which are internet-smart. So when my internet bandwidth tanks and it takes five minutes to load a YouTube video, I want to know what's going on, and there are many potential culprits. I'd like to be able to plug my MacBook into the primary router and see a nice little dashboard of the units on the network and what kind of bandwidth each is using at that moment. I could figure this out from WireShark or tcpdump but figure there has to be an easier way. I've tried a few different commercial products but none really presented the right info. Suggestions? (This may be a question for superuser since my Apple Time Capsule's SNMP capabilities are limited, but I figure admins of small business networks would have dealt w/ the same issue..)

  Read the article

• Remote reboot of windows to knoppix

  - by user64452

  I am attempting to develop an Auditing application. This audit application will be employed on windows networks. The Audit will need to discover Hardware and software details of all machines attached to the network (including Printers) I do not want to have to install this application on each workstation. The audit app. needs to discover all the ip addresses of all the networked workstations. I have been prototyping this app for the last couple of months and have decided to try a new tack Is this possible? a). You have a windows network, min Windows XP sp3 and upwards b). Maximum of 100 Networked machines (if that matters) c). I need to remotely reboot each WINDOWS machine in turn on the entire network and get it to startup using UNIX, say knoppix for example! d). however the knoppix live cd is only available from one of the networked machines Questions... Morphology? Longevity? Incept dates? Cheers DD

  Read the article

• Would a switch be covered by a router's firewall

  - by Uh-yeah...

  So... Hopefully; this is the right place for this question. I need more Ethernet ports on my home network. Sadly, we already have an old router connected to the main router and we still need more ports. I feel dumb for asking; but, I just would like to double check. Would the devices connected to the switch be "protected" by the Main router's firewall? ? Up to this point I have assumed that was the case; but, a co-worker is convinced that is not the case [ I believe he is thinking of a situation in which the switch (un-managed) is before an access point]. [It would go modem to main router; main router then has the switch and old router connected to it.

  Read the article

• Establish direct cable connection between Windows 8 PCs in home network

  - by Marie. P.

  I'm running two PCs, a desktop and a laptop with Windows 8 Release Preview ("Build 8400"). They are connected to the same router in infrastructure mode, thereby having wireless internet. Due to often file synchronization between the machines I want to establish a cable connection that allows direct file transfer, without needing to use the wireless. When I plug in the cable (normal, not cross-over), I see in "Control Panel\Network and Internet\Network Connections": "Ethernet - unidentified Network" on both PCs. Transferring a file between both still only uses the WiFi via the Router. I noticed that when turning off the wifi on one PC, I can set up a shared internet connection that will work via Ethernet-cable, but since sometimes only one PC runs, sometimes the other one, I do not want to have the internet of one machine to be dependent on the other one being switched on. I do not have a crossover-cable, but since I did connect the PCs already successfully (just without both being on the internet), I'm sure that this should also work with a normal ethernet cable.

  Read the article

• 'hijacking' gui and mapping certain controls to certain functions. VNC. TouchOSC

  - by Nick

  I need a VNC LIKE application which rather than sharing the screen, can take control of a specific application and then share that functionality across a network to multiple clients. Obviously, VNC requires use of the mouse and therefore only one user can do something at one time, this is NOT what I am after. I am after something that can hijack the graphic user interface, map certain controls, and then display them in another piece of software (perhaps like TOUCHOSC) The software I would like to map and share is called YAMAHA STUDIO MANAGER and is used to control certain Yamaha audio hardware, and in my case a Yamaha LS9 and M7CL mixing console. Its free.

  Read the article

• Troubleshooting Network Speeds -- The Age Old Inquiry

  - by John K

  I'm looking for help with what I'm sure is an age old question. I've found myself in a situation of yearning to understand network throughput more clearly, but I can't seem to find information that makes it "click" We have a few servers distributed geographically, running various versions of Windows. Assuming we always use one host (a desktop) as the source, when copying data from that host to other servers across the country, we see a high variance in speed. In some cases, we can copy data at 12MB/s consistently, in others, we're seeing 0.8 MB/s. It should be noted, after testing 8 destinations, we always seem to be at either 0.6-0.8MB/s or 11-12 MB/s. In the building we're primarily concerned with, we have an OC-3 connection to our ISP. I know there are a lot of variables at play, but I guess I was hoping the experts here could help answer a few basic questions to help bolster my understanding. 1.) For older machines, running Windows XP, server 2003, etc, with a 100Mbps Ethernet card and 72 ms typical latency, does 0.8 MB/s sound at all reasonable? Or do you think that slow enough to indicate a problem? 2.) The classic "mathematical fastest speed" of "throughput = TCP window / latency," is, in our case, calculated to 0.8 MB/s (64Kb / 72 ms). My understanding is that is an upper bounds; that you would never expect to reach (due to overhead) let alone surpass that speed. In some cases though, we're seeing speeds of 12.3 MB/s. There are Steelhead accelerators scattered around the network, could those account for such a higher transfer rate? 3.) It's been suggested that the use SMB vs. SMB2 could explain the differences in speed. Indeed, as expected, packet captures show both being used depending on the OS versions in play, as we would expect. I understand what determines SMB2 being used or not, but I'm curious to know what kind of performance gain you can expect with SMB2. My problem simply seems to be a lack of experience, and more importantly, perspective, in terms of what are and are not reasonable network speeds. Could anyone help impart come context/perspective?

  Read the article

• I have a wireless Canon P560 and my computer can't find it

  - by ed

  The printer is wireless and I haven't connected it via USB. I set the configurations for the Wi-Fi access point in the printer and it connected to my Wi-Fi. I have AT&T as the service provider and the 2Wire router. When I access the router in the browser I see that the printer is connected but when I run the software to detect the printer the computer can't find it. I have a Mac with Snow Leopard. I tried to detect the printer with another device and it can't find it. Is there a port that needs to be open for wireless printers? Because I tried putting the routers firewall settings for the device to its lowest and the computer still can't find it. Let me know. Thnx.

  Read the article

• Newly installed DIR-615 - how to connect to the wireless?

  - by JK123

  I've just installed a D-Link DIR 615, but can't figure out how to connect to the wireless.. When I double click my wireless icon in the tray, it does show the new network. Its starts the "WiFi protected setup wizard" and the first thing it asks for is the "Device Ownership Password". I have no idea what that is - I've tried the PIN and the router password. On the next page it says: SSID: _(name)__ Security type: _wpa2 personal aes ccmp_ Password: _some long key that is not what I entered during router setup_ I change the key to the one I created when setting up the router. I've also tried leaving the key as it is shown in the dialog. But it does not connect either way. All it says is "Configuration failed" So how do I connect to the new wireless network??

  Read the article

• Where does Vista/Windows 7 store Wireless Connection Information?

  - by BEn

  I am attempting to clean out my dad's laptop, which is running Windows Vista. Somehow, he has managed to accrue 1,400 wireless networks in the "Manage Wireless Networks" control panel. Is there any easy way to clear this list short of reinstalling Windows?

  Read the article

• Network Table assistance

  - by mitchnufc

  I am designing a small network and have came up with the following table I am just wondering if this seems right, would appreciate some feedback, thanks. Network/Router First IP Last IP Subnet Host Broadcast Router 1 162.10.0.1 162.10.0.7 255.255.255.248 162.10.0.0 162.10.0.8 Network 1 162.10.1.1 162.10.2.253 255.255.254.0 162.10.1.0 162.10.2.254 Network 2 162.10.0.9 162.10.0.14 255.255.255.248 162.10.0.8 162.10.0.15 Router 2 162.10.0.17 162.10.0.18 255.255.255.252 162.10.0.16 162.10.0.19 Network 3 162.10.0.21 162.10.0.146 255.255.255.128 162.10.0.20 162.10.0.147 Router one is the IP assigned by the ISP

  Read the article

• TCP/IP communication between Hyper-V host and guests

  - by Tedd Hansen

  This may be a simple one. :) I have a simple Hyper-V setup with a few guest os running. The host has 1 physical network adapter with a static IP assigned to it. The guests have network adapters assigned to "Internet" (Hyper-V network) which is bound to the physical host network adapter (Hyper-V "External" connection type). I am not able to communicate (ping or anything else) between guests and host. I've checked firewall and it seems fine (ports open from anywhere still don't work). I'm trying to communicate with the hosts IP assigned to the same physical interface that the guests are sharing. Guests can communicate between them just fine. I can't seem to find any relevant setting (I might just be missing it). So my questions: How do I fix it so host and guests can communicate?

  Read the article

< Previous Page | 370 371 372 373 374 375 376 377 378 379 380 381  | Next Page >