Search Results

Search found 15819 results on 633 pages for 'django errors'.

Page 375/633 | < Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >

• HDDs randomly falling off raid

  - by michael

  I really need help on this it's Saturday long weekend.No customer service help:( .I recently build new server/light duty desktop.Main purpose is only file sharing.Raid configuration :Adaptec 6805 ,8x 3TB HDD WD Red,Intel RES2SV240 expander,Raid 6,set in Intel mobo DZ 77GA-70K.I upgraded firmwares, but I'm having strange problem. During Build Verify segment 7 got missing.I just reinsert drive into hot swap bay and it started to rebuild Array.After rebuild was done another segments 0 and 5 gone missing while build/verify.I reinserted drives and now I'm praying that raid is going to rebuild successfully from remaining 6 drives,because i already transfer some data on it(I know it was bad idea).I checked S.M.A.R.T on missing drives , it only says link failure and aborted commands on one of them.No Errors on HDDs.Connections and cables are good.I added 2 fans blowing on RAID controller because it was getting too hot, so I guess overheating shouldn't be issue.What can be possibly wrong? Thank you for help.

  Read the article

• Apache stops serving requests when connections increase

  - by Gunjan

  The values for MaxClients, ServerLimit etc parameters are quite high (4000). Available RAM on the server is high too (~8G). Load average remains below 1 on a 24 core CPU. But when the number of visitors on the website increase apache just stops serving requests. The apache error log is blank and access log shows no more requests coming in. Restarting apache makes it work again until the number of requests increases again. Any ideas where to start looking? UPDATE Getting the below errors in apache error log on running it with LogLevel Debug [info] server seems busy, (you may need to increase StartServers, or Min/MaxSpareServers), spawning 32 children, there are 479 idle, and 1027 total children

  Read the article

• PcLinuxOs demands I use only one repository at time. Is it right?

  - by m33600

  I come to your presence with this question that is paralyzing my coding efforts. PclinuxOs was my distro of choice for reliability, but it is jealous and does not permit me to add repos from, say, Debian. The wiki is clear advising on using just one repo, and I end up not finding what I used to find on normal Debians. Multimon, the audio decoder, for example (my other question) is not there. When I try to install multimon with hammer and plies, it returns errors of all kinds. Is there a way to safely and temporarily add a repository, make the install and remove the repo, returning pclinuxos to its stable state?

  Read the article

• Screen tail -f window closes immediately

  - by t.heintz

  I have this in my ~/.screenrc file: startup_message off screen -t top 0 top screen -t log 2 tail -f /path/to/application/log/* screen -t action 1 #caption always "%?%F%{.R.}%?%3n %t%? [%h]%?" hardstatus alwayslastline "%-Lw%{= BW}%50>%n%f* %t%{-}%+Lw%<" When I start screen, it opens all three windows, but as soon as I try to switch to window 2, it closes immediately. I would assume there is a problem with the shell and it exits instantly, but I can't find anything wrong with it. I have tried using quotation marks around the path and the entire command, which only leads to "file not found" errors. The command works just fine when I enter it directly into a shell. The screen version is: Screen version 4.00.02 (FAU) 5-Dec-03 Help?

  Read the article

• Installing grub2 on ubuntu with software raid mirroring

  - by Marko

  Can someone help me out on this? I accidentally installed grub on usb flash drive during ubuntu server installation. Now I cant boot system without drive attached to server. I want to install grub on hard drive with grub-install but i don't know what to set as location for boot loader? my fstab looks like this: file system mount point type options dump pass proc /proc proc nodev,noexec,nosuid 0 0 /dev/mapper/pdc_jdbeghhjg1 / ext4 errors=remount-ro 0 1 /dev/mapper/pdc_jdbeghhjg5 none swap sw 0 0 and partition tables for hard drives as this: Device Boot Start End Blocks Id System /dev/sda1 2048 1215662079 607830016 83 Linux /dev/sda2 1215664126 1249998847 17167361 5 Extended /dev/sda5 1215664128 1249998847 17167360 82 Linux swap / Solaris Device Boot Start End Blocks Id System /dev/sdb1 1 75672 607830016 83 Linux /dev/sdb2 75672 77809 17167361 5 Extended /dev/sdb5 75672 77809 17167360 82 Linux swap / Solaris ?

  Read the article

• OpenVPN and brouting issue

  - by JavierMartinz

  I have a Guest XEN Machine in which I want to connect by OpenVPN to other network. But I have this problem: when I want to connect to that OpenVPN I get a lot of TLS handshake errors because I think that the packages did not come rightly. When, at the end, the guest machine achieve to connect (after several tries) I can't ping the other machines of the OpenVPN network. Except sometimes, where if I ping 20 times MAYBE i get ping-answer in 1-2 times. I think that this problem is related about how the HOST Xen machine 'filters' the packages to the bridge. I mean, I think that all the outgoing guest machines packages are good but the incoming traffic to the guests is not recognized well. How could I detect/solve the problem? Im using Debian Linux in both machines

  Read the article

• Can't delete folder in Windows 7

  - by user18526

  I'm trying to delete a folder in Windows 7 and get a perplexing error message: "Could not find this item: This is no longer located in G:\Graphics. Verify the item's location and try again. I can see the folder -- I can find it. I just can't delete it. I also get a second error message (sometimes) when I click on the folder: G:\Graphics 2009-11-17 refers to a location that is unavailable...this information might have been moved to a different location. I'm using Windows 7; this folder is on an external hard drive. I've emptied the folder (there were items in it); I've scanned that external hard drive for errors. Trying to rename the folder yields the same enigmatic error message. Is there a way to delete this folder?

  Read the article

• Internet Explorer 9 - website certificate expired

  - by user155504

  My Internet Explorer 9, for every page, shows this messege to me: There is a problem with this website"s security certificate. The security certificate presented by website has expired or is not yet valid. Security certificate problems may indicate an attempt to fool you or intercept any data you send to the server. We recommend that you close this webpage and do not continue to this website. Click here to close this webpage. Continue to this website (not recommended)" and afterwards it shows this : Internet Explorer blocked this website from displaying content with security certificate errors [show content] Please help me to resolve this problem!

  Read the article

• Request exceeded the limit of 10

  - by Webnet

  My logs are FULL of [Tue Jan 11 10:20:45 2011] [error] [client 99.162.115.123] Request exceeded the limit of 10 internal redirects due to probable configuration error. Use 'LimitInternalRecursion' to increase the limit if necessary. Use 'LogLevel debug' to get a backtrace., referer: https://www.domain.com/vehicles/Chevrolet/Uplander/2006 The problem is when I enable LogLevel debug we get HUGE error logs because all of our traffic is SSL. From what I can tell the file doesn't record these errors anymore, either that or it's so buried in SSL logs that I just can't find them. Here's my .htaccess Options -indexes RewriteEngine On RewriteRule ^battery/([^/]+)$ /browser/product?sku=BATTERY+$1&type=battery RewriteRule ^vehicles/([^/]+)/([^/]+)/([^/]+)/product([0-9]+)$ /browser/index.php?make=$1&model=$2&id=$3&%{QUERY_STRING} [L,NC] RewriteRule ^vehicles/([^/]+)/([^/]+)/([^/]+)/([0-9]+)$ /browser/product.php?make=$1&model=$2&year=$3&id=$4&%{QUERY_STRING} [L,NC] RewriteRule ^vehicles/([^/]+)/([^/]+)/([^/]+)$ /store/product/list.php?make=$1&model=$2&year=$3&%{QUERY_STRING} [L,NC] RewriteRule ^vehicles/([^/]+)/([^/]+)$ /vehicle/make/model/year/list.php?make=$1&model=$2&%{QUERY_STRING} [L,NC] RewriteRule ^vehicles/([^/]+)$ /vehicle/make/model/list.php?make=$1&%{QUERY_STRING} [L,NC]

  Read the article

• Debian Based Server not booting, soon after GRUB screen it restarts?

  - by Krauser

  I have tried running memtest, it start get about half way then abruptly restarts. I assume this is not a problem with the OS itself but rather a hardware issue, I have checked various logs when after about 10 reboots it starts ok, /var/log/kern.log /var/log/syslog /var/log/dmesg All I get is: EXT4-fs(sdc1): re-mounted. Opts: errors=remount-ro restart So I ran fcsk on the drive, to check if the fs was failing and it was fine. Really don't know how to find why the server is continuosly restarting andif I get lucky it will boot up.

  Read the article

• Windows 8: 100% disk active time, no actual data transferred

  - by fingerbangpalateclick

  Occasionally, like several times an hour, my hard drive will appear to lock up: Task Manager will show 100% active time with read and write speeds of 0. I can still switch between open windows, but anything that requires a disk access will stall for around a minute until the hard disk starts working properly again. It happens at apparently random intervals, and only happens in Windows 8. Not 7, nor Linux. It is probably not a problem with the disk itself: This is a relatively new hard drive, and S.M.A.R.T. is showing no errors. Only happens in Windows 8: not any other OS that has used the same partition, or different partitions. So, what is going on? How can I fix this? Note: this is a different problem then this one: Extremely high disk activity without any real usage My task manager would look similar, but Average Response Time, Read Speed, and Write Speed would all be 0.

  Read the article

• How can I run fsck on a disk image via Mac Terminal?

  - by mvizual

  I want to run fsck on a disk image before I use it to restore (replace) a corrupted volume. Using Terminal, what would be the proper command, syntax, and options for this operation? I've just recently become acquainted with Terminal and line commands, so syntax and specific options aren't part of my computing vocabulary. I'm using Terminal 2.1.2, bash, OS 10.6.8. Ultimately, I'm trying to restore an image to a secondary startup volume (external drive). The image is mounted on my desktop and I want to check it for errors before I use it. Disk Utility runs "repair disk" successfully but the integrity of the image is suspect.

  Read the article

• Could 11.5 Million 401's be causing bottlenecks?

  - by roviuser

  I'm going to preface this with a warning: My knowledge about servers and networking is VERY limited, and if you provide me with technical answers, I probably won't understand much until I research your answer further. I'm trying to expand my knowledge and learn about it, though. If the information that I am able to provide in this question is insufficient to answer the question, I understand, and it can be closed. We have a SharePoint 2007 system that is extremely slow, mostly from huge amounts of use. We've been told that the main speed bottleneck is the access to the sql databases. However, they do provide a statistics dashboard, so I did some poking around, and noticed that we have 11.5 million or more 401 - access denied errors every month. Could this be causing major speed/performance decreases? Authentication for sharepoint uses active directory.

  Read the article

• Has anyone seen an HTTP 500 error when HTTPS traffic going through Pound Proxy forwards to an HTTP page?

  - by scientastic

  We have Varnish as our load balancer and reverse proxy cache for normal HTTP traffic. For HTTPS traffic, we use Pound proxy to unwrap the SSL and forward to Varnish, which then forwards to the back-end servers. This is used for our "checkout" process to encrypt credit card info in transition. However, on the last stage of checkout, users are always getting an HTTP 500 (Internal Server) error. It doesn't seem to be due to our back-end app server, by all tests I've tried. Does anyone know anything about how that transition works-- the transition back from HTTPS to HTTP and the interaction between Pound and Varnish-- and why it might cause 500 errors?

  Read the article

• Network location is not on the Domain

  - by Kyle Brandt

  I have a computer joined to the domain, but it doesn't view the network "location" as being part of the domain. I have tried removing and rejoining the domain and this doesn't help: Other computers in the same network don't have this problem. I have also tried several different icons, including both the train and the airplane which doesn't seem to make a difference. At least using nslookup, the server seems to have connectivity with the DCs in the same site. There also seem to be some errors that suggest a NULL domain: Computer: OR-WEB05.ds.stackexchange.com Description: NtpClient was unable to set a domain peer to use as a time source because of failure in establishing a trust relationship between this computer and the '' domain in order to securely synchronize time. NtpClient will try again in 3473457 minutes and double the reattempt interval thereafter. The error was: The trust relationship between this workstation and the primary domain failed. (0x800706FD)

  Read the article

• Snapshots are disappearing from Time Machine. Why?

  - by AntonAL

  I have TimeMachine enabled for my external HDD. I'm triggering backups manually 2 times per week. I have noticed, that some snapshots, that i made, are gone. I noticed this behaviour several weeks later, but i had doubts. To make it sure, i've recorded screen video with listing snapshots in TimeMachine. After watching my screen recording today, I'm sure, that for Augusut i had 9 snapshots. Now, i have only 3 of them. What's happening ? I had no crash disk reports, errors etc

  Read the article

• SCCM Client Push FAIL - Win2000 box

  - by ajp

  When trying to install the SCCM client onto a Windows 2000 box, the install fails. The install script is run through a batch file (CONTENTS: \mdop\SCCM_client\ccmsetup.exe /mp:MDOP /logon smssitecode=MID smsslp=MDOP) hosted on a public area of the network. This script has worked for all machines (mostly Win2003 Server). I've tried enabling all the common services it requires (BITS, IIS Admin, Windows Installer), but it still only runs for a second or two then quits. Here's the piece of the log file where it errors out: [LOG[Couldn't get directory list for directory 'http://MDOP/CCM_Client/ClientPatch'. This directory may not exist.]LOG]! time="13:55:53.618+300" date="06-30-2009" component="ccmsetup" context="" type="0" thread="1676" file="ccmsetup.cpp:6054" Full Log: http://paste-it.net/public/gb11732/

  Read the article

• MS 2008 R2 Drops Remote Desktop Sessions in 10 seconds or less every time

  - by mike42

  I'm adding a new 64-bit server to our domain. Everything seems fine except when accessing the machine using remote desktop, after a few seconds the connection is lost. The error message is "This computer can't connect to the remote computer." "Try connecting again. If the problem continues, contact the owner of the remote computer or your network administrator." A similar result with Telnet on port 3389. I am able to connect but if I hit a key the connection to host lost. The event log shows the successful login. No errors. Any ideas?

  Read the article

• SSH tunnel doesn't work

  - by s1ck

  I am trying to use my server as a "proxy" with ssh. However, setting up tunneling with ssh -D localhost:8000 user@myserver does not work. I tested this on various machines with ssh and putty - It connects just fine, but when I set my browser settings accordingly, I just get an error "Connection has been reset". I tried monitoring the traffic with wireshark, but I didn't even see some tunnel-traffic. I explicitly set AllowTcpForwarding to "yes" but I still can't use the tunnel. When running ssh in verbose mode, I don't get any errors but debug1: Connection to port 8000 forwarding to socks port 0 requested. debug1: channel 3: new [dynamic-tcpip] debug1: channel 3: free: dynamic-tcpip, nchannels 4 What am I doing wrong?

  Read the article

• putty 0.61 : why do I see "Access Denied" message after I enter my login id?

  - by anjanbacchu

  I use putty to login to my RHEL 5.3 server. I'm prompted to enter my login as "login as " and I enter my login Id. as soon as I press ENTER, I see a "Access Denied" message following which I'm prompted with password. I successfully enter password and I'm through -- no problems. I tried the same with putty 0.60(as opposed to above putty 0.61) but in this version, I don't get any "access denied" error. What should I make of this ? Is putty 0.61 version buggy ? P.S : If I login using ssh.exe(from cygwin), then I'm fine -- I don't get any "access denied" errors. Thank you,

  Read the article

• What command line tools for monitoring host network activity on linux do you use?

  - by user27388

  What command line tools are good for reliably monitoring network activity? I have used ifconfig, but an office colleague said that its statistics are not always reliable. Is that true? I have recently used ethtool, but is it reliable? What about just looking at /proc/net 'files'? Is that any better? EDIT I'm interested in packets Tx/Rx, bytes Tx/Rx, but most importantly drops or errors and why the drop/error might have occurred.

  Read the article

• E2K7: Can't add jounaling mailbox to storage group

  - by Agent

  We just added a new SG to a standalone E2K7 server but Exchange pops an error when we try to enable journaling on it. The journal recipient mailbox was created a while back and as far as we can tell there are no issues with it. It's viewable in the GAL and accessible through OWA. The error is: Set-Mailboxdatabase Error:Obkect "domain.company.com/Journaling/Journal5" could not be found. Please make sure that it was spelled correctly or specify a different object. This Journal5 account is in a child domain (like all the other journaling mailboxes we have attached to other mailbox server SGs). We also tried attaching one of the working journaling mailboxes to this SG but they also popped back the same error. Event log is now showing any errors at all. We are running SP1 on this server. I've tried dismounting/remounting the store and bouncing the IS and SA services but that didn't help any. Any suggestions?

  Read the article

• Tar an gzip together, but the other way round?

  - by Boldewyn

  Gzipping a tar file as whole is drop dead easy and even implemented as option inside tar. So far, so good. However, from an archiver's point of view, it would be better to tar the gzipped single files. (The rationale behind it is, that data loss is minified, if there is a single corrupt gzipped file, than if your whole tarball is corrupted due to gzip or copy errors.) Has anyone experience with this? Are there drawbacks? Are there more solid/tested solutions for this than find folder -exec gzip '{}' \; tar cf folder.tar folder

  Read the article

• How to install stuff on Ubuntu

  - by Industrial

  Hi everyone, I have just launched my first EC2 instance and choosed a Ubuntu image to start from, since it's quite well documented. However, I am trying to install the Redis package: http://packages.ubuntu.com/lucid/redis-server Maybe I am not googling properly or just stupid since the weekend is approaching, but I'll keep getting errors: root@ip-10-229-123-199:~# sudo apt-get install redis-server Reading package lists... Done Building dependency tree... Done E: Couldn't find package redis-server I'll assume that I need to add a repository or something to Ubuntu to help it find the package I want, but how do I do it? I can only find graphical guides which doesnt help me too much since I am using SSH. Thanks alot!

  Read the article

• Get SMTP to work

  - by user664408

  We upgraded to exchange 2010 and this broke an old java based script that connected and sent out e-mail messages. Many hours later we still can't get exchange to work like exchange 2003 did. That hope was abandoned and we decided to create a linux postfix server to forward the e-mail from the old system to exchange, eliminating exchange on the java side. This still doesn't work with similar errors. I need help figuring out what is different between exchange 2003 with SSL and authentication and the new servers, both linux and exchange 2010. My guess is both have TLS and for some reason the java code won't revert back to the older version of SSL, instead it just fails. Can someone help me either setup exchange 2010 to work like 2003 used to, OR to setup postfix to mandate it use SSL 2.0 instead of TLS? unfortunately no one knows anything about the Java code and they can't decompile it apparently. Any help is appreciated.

  Read the article

< Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >