Search Results

Search found 27946 results on 1118 pages for 'output buffer empty'.

Page 375/1118 | < Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• Immediate logout after login with PAM, Kerberos, and LDAP

  - by Dylan Klomparens

  I've set up remote login on a computer using Kerberos and LDAP. I've also configured NFS to mount onto /home so that the user's home directory is the same wherever they login. Kerberos authentication seems to work fine. I can get a ticket using kinit user1 (assuming user1 is a remote user) and see the ticket with klist. I'm pretty sure LDAP is working because I see the proper output from getent passwd, which lists all the remote users. The contents of /home are present when I list the files. The problem is: when I try to login as a remote user the session is immediately ended. Why is it not letting me stay logged in? Here is the output from /var/log/messages after a login attempt: # /var/log/messages: Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: authentication succeeds for 'user1' ([email protected]) Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (establish credential) called Oct 9 10:57:53 tophat login[6472]: pam_krb5[6472]: pam_setcred (delete credential) called EDIT: The distro is openSUSE. Here are the common-* files in /etc/pam.d:   # /etc/pam.d/common-account account required pam_unix.so   # /etc/pam.d/common-auth auth sufficient pam_krb5.so minimum_uid=1000 auth required pam_unix.so nullok_secure try_first_pass   # /etc/pam.d/common-session session optional pam_umask.so umask=002 session sufficient pam_krb5.so minimum_uid=1000 session required pam_unix.so There doesn't appear to be a /var/log/auth.log file nor a /var/log/secure file.

  Read the article

• Adding custom service to nagiosgraph

  - by ravloony

  I have successfully added nagiosgraph to our nagios installation. I also added a memory checker plugin, from here : http://blog.vergiss-blackjack.de/2010/04/nagios-plugin-to-check-memory-consumption/. However I can't seem to get the graph of this service to be output by nagiosgraph. The plugin returns a single line like this: 31% (3785 of 11903 MB) used so i added a rule like this to the map file: /output:(\d+)% \((\d+) of (\d+) MB\) used/ and push @s, ['Mem', ['Percentage', 'GUAGE', $1], ['Used', 'GUAGE', $2], ['Total', 'GUAGE', $3] ]; I have also read this : http://www.mail-archive.com/[email protected]/msg36835.html and made sure that process_performance_data=1 in the nagios conf file. So far I have no graph for the Mem service on any host, and no rrd file either. I am unsure how to proceed to get this working. The documentation is rather difficult to follow and I haven't managed yet to understand it enough to do this. Can anyone point me to a tutorial, or some documentation which explains the steps needed to get a service noticed and graphed by nagiosgraph?

  Read the article

• Blocking an IP in Webmin

  - by Dan J

  I've been checking my /var/log/secure log recently and have seen the same bot trying to brute force onto my Centos server running webmin. I created a chain + rule in Networking - Linux Firewall: Drop If source is 113.106.88.146 But I'm still seeing the attempted logins in the log: Jun 6 10:52:18 CentOS5 sshd[9711]: pam_unix(sshd:auth): check pass; user unknown Jun 6 10:52:18 CentOS5 sshd[9711]: pam_succeed_if(sshd:auth): error retrieving information about user larry Jun 6 10:52:19 CentOS5 sshd[9711]: Failed password for invalid user larry from 113.106.88.146 port 49328 ssh2 Here is the contents of /etc/sysconfig/iptables: # Generated by webmin *filter :banned-ips - [0:0] -A INPUT -p udp -m udp --dport ftp-data -j ACCEPT -A INPUT -p udp -m udp --dport ftp -j ACCEPT -A INPUT -p udp -m udp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport 20000 -j ACCEPT -A INPUT -p tcp -m tcp --dport 10000 -j ACCEPT -A INPUT -p tcp -m tcp --dport https -j ACCEPT -A INPUT -p tcp -m tcp --dport http -j ACCEPT -A INPUT -p tcp -m tcp --dport imaps -j ACCEPT -A INPUT -p tcp -m tcp --dport imap -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3s -j ACCEPT -A INPUT -p tcp -m tcp --dport pop3 -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp-data -j ACCEPT -A INPUT -p tcp -m tcp --dport ftp -j ACCEPT -A INPUT -p tcp -m tcp --dport domain -j ACCEPT -A INPUT -p tcp -m tcp --dport smtp -j ACCEPT -A INPUT -p tcp -m tcp --dport ssh -j ACCEPT -A banned-ips -s 113.106.88.146 -j DROP COMMIT # Completed # Generated by webmin *mangle :FORWARD ACCEPT [0:0] :INPUT ACCEPT [0:0] :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed # Generated by webmin *nat :OUTPUT ACCEPT [0:0] :PREROUTING ACCEPT [0:0] :POSTROUTING ACCEPT [0:0] COMMIT # Completed

  Read the article

• AviSynth ChangeFPS: combining videos with different framerates

  - by Daniel Saner

  I have two video recordings of the same scene, but with different framerates, that I would like to combine using an AviSynth script. One video is recorded at 30fps, the other at 120fps. What I would like to do is to keep them temporally synchronised, meaning that for each frame of the 30fps video, the output should display 4 frames from the 120fps video. I would like the final output video to play at 30fps so that the duration is 4 times the original recordings. From AviSynth's documentation, it seems ChangeFPS is the function I'll need, since it removes and duplicates frames, while 'AssumeFPS' just changes the playback speed (and my plan is basically to quadruple every frame of the 30fps clip). However, the filter does not seem to do what it says. If I try: clip30 = AviSource("0326.avi").ChangeFPS(120) clip120 = AviSource("0326-120fps.avi") it doesn't affect the playback speed or frame count of the 30fps clip at all, but removes every fourth frame from the 120fps clip, which is not at all what I want. Unfortunately, appending .ChangeFPS(7.5) to the clip120 instead does not have the same inverse effect—in that case, it does exactly what's to be expected. Alternatively, if I try: clip30 = AviSource("0326.avi").AssumeFPS(7.5) clip120 = AviSource("0326-120fps.avi") there is no effect at all, both clips are played back at 30fps, meaning that only a quarter of the 120fps clip has been shown by the time the 30fps clip is over. So how can I combine these two clips in the manner I want? I was unable to find any other internal or external filters that would help me do that. It seems to me that if ChangeFPS did what the manual says, it would be the right one for the job.

  Read the article

• Local Apache Web server works only when connected to the net

  - by Jean

  Hello, I installed Ubunut and got the LAMP stack installed too. Now the problem is I have to be connected to the internet for the local apache webserver to work, else it does not. I changed the IP address on the dnshost, in the apache2.conf file, got the servername in the httpd.conf, which was empty. Any ideas guys. Thanks Jean

  Read the article

• FFmpeg convert video w/ dropped frames, out of sync

  - by preahkumpii

  I recorded a video using Bandicam with the MJPEG encoder to get the least amount of lag. Now, I am trying to convert that massive file to a h264 avi using ffmpeg. I know there are dropped frames in the video stream...more than 100 in the first two minutes, which I assume is simply because Bandicam dropped some when it couldn't keep up. So, when I convert the file to h264, the video and audio are out of sync, and appear to be more and more out of sync as output video progresses. Here is my basic command in ffmpeg: ffmpeg -i "C:\...\input.avi" -vcodec libx264 -q 5 -acodec libmp3lame -ar 44100 -ac 2 -b:a 128k "C:\...\output.avi" I have tried EVERYTHING I can think of including: -itsoffset [-]00:00:01 Tried this before and after input file. This doesn't work because as the video progresses it becomes more and more out of sync. -async 1 Doesn't work. -vsync 1 Doesn't work, but it does show dropped frames being duplicated. Two inputs of same file with mapping using -map 0:0 -map 1:1. Doesn't work. The source plays just fine. Any ideas how to convert it with ffmpeg and keep the audio and video synced? Thanks.

  Read the article

• VPN access configuration with ForeFront TMG

  - by Yang

  I am trying to configure VPN Client access with ForeFront TMG. When I try to add domain groups to allow access to them, under Group column I can only see the SID of the domain group. And the Domain column ends up empty. ForeFront TMG is joined to the domain. Can you think of a reason?

  Read the article

• Can't connect to vsftpd on Ubuntu 10.04

  - by Johnny

  I started the vsftpd on Ubuntu 10.04, but can't connect to it. The error says(FTP Client): Status: Connecting to 124.205.xx.xx:21... Error: Connection timed out Error: Could not connect to server I've checked the server status, and vsftpd is running: $ ps ax | grep vsftpd 23646 ? Ss 0:00 /usr/sbin/vsftpd 23650 pts/1 S+ 0:00 grep --color=auto vsftpd port 21 is under listening as well: $ netstat -tlnp | grep 21 (No info could be read for "-p": geteuid()=1000 but you should be root.) tcp 0 0 0.0.0.0:21 0.0.0.0:* LISTEN - I can connect to localhost: $ ftp localhost Connected to localhost. 220 (vsFTPd 2.2.2) Name (localhost:jlee): 331 Please specify the password. Password: 230 Login successful. Remote system type is UNIX. Using binary mode to transfer files. ftp> Here is iptables output $ sudo iptables -vL Chain INPUT (policy ACCEPT 191 packets, 144K bytes) pkts bytes target prot opt in out source destination Chain FORWARD (policy ACCEPT 0 packets, 0 bytes) pkts bytes target prot opt in out source destination Chain OUTPUT (policy ACCEPT 124 packets, 28502 bytes) pkts bytes target prot opt in out source destination What's the problem here?

  Read the article

• unable to recover data from failed hdd

  - by Eslam Elyamany

  my hdd failing (or maybe totally dead) i've connected the hdd via USB but it doesn't appear in fdisk Disk /dev/sda: 500.1 GB, 500107862016 bytes 255 heads, 63 sectors/track, 60801 cylinders, total 976773168 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 4096 bytes I/O size (minimum/optimal): 4096 bytes / 4096 bytes Disk identifier: 0xe9fb38fb Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 40959999 20376576 7 HPFS/NTFS/exFAT /dev/sda4 40962046 976771071 467904513 5 Extended Partition 4 does not start on physical sector boundary. /dev/sda5 82913280 86910975 1998848 82 Linux swap / Solaris /dev/sda6 86913024 394113023 153600000 7 HPFS/NTFS/exFAT /dev/sda7 40962048 82913279 20975616 83 Linux /dev/sda8 394122708 976768064 291322678+ 7 HPFS/NTFS/exFAT Partition 8 does not start on physical sector boundary. no sdc appears here , BUT it's appears on /dev/ rootghost-lap:/home/ghost# ls /dev/sd* /dev/sda /dev/sda2 /dev/sda5 /dev/sda8 /dev/sdb /dev/sdc1 /dev/sdc2 /dev/sdc6 /dev/sdc8 /dev/sda1 /dev/sda4 /dev/sda6 /dev/sda9 /dev/sdc /dev/sdc10 /dev/sdc5 /dev/sdc7 /dev/sdc9 also it appears in proc Code: rootghost-lap:/home/ghost# cat /proc/partitions major minor #blocks name 8 0 488386584 sda 8 1 102400 sda1 8 2 20376576 sda2 8 4 1 sda4 8 5 1998848 sda5 8 6 153600000 sda6 8 8 291322678 sda8 8 9 20975616 sda9 11 0 1048575 sr0 11 1 99136 sr1 8 32 244198583 sdc 8 33 14651248 sdc1 8 34 1 sdc2 8 37 15380480 sdc5 8 38 4153344 sdc6 8 39 48829536 sdc7 8 40 48829536 sdc8 8 41 110374551 sdc9 8 42 1975963 sdc10 and dmesg : [10604.777168] end_request: I/O error, dev sdc, sector 1 [10604.817238] sd 26:0:0:0: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [10604.817243] sd 26:0:0:0: [sdc] Sense Key : Aborted Command [current] [10604.817248] sd 26:0:0:0: [sdc] Add. Sense: No additional sense information [10604.817253] sd 26:0:0:0: [sdc] CDB: Read(10): 28 00 00 00 00 02 00 00 06 00 ok now , let's see what i've tried testdisk to check for partitions -- failed dd to copy data from /dev/sdcX -- provide strange output size for example /dev/sdc1 is about 15G , the output for dd is 62G+ so i had to cancle it safecopy successfully made an image for partitons , but can't fix images, can't mount it, can't do any thing with it and some other tools i've tried and all failed , so any idea ?

  Read the article

• Postfix SMTP-relay server against Gmail on CentOS 6.4

  - by Alex

  I'm currently trying to setup an SMTP-relay server to Gmail with Postfix on a CentOS 6.4 machine, so I can send e-mails from my PHP scripts. I followed this tutorial but I get this error output when trying to do a sendmail [email protected] Output: tail -f /var/log/maillog Apr 16 01:25:54 ext-server-dev01 postfix/cleanup[3646]: 86C2D3C05B0: message-id=<[email protected]> Apr 16 01:25:54 ext-server-dev01 postfix/qmgr[3643]: 86C2D3C05B0: from=<[email protected]>, size=297, nrcpt=1 (queue active) Apr 16 01:25:56 ext-server-dev01 postfix/smtp[3648]: 86C2D3C05B0: to=<[email protected]>, relay=smtp.gmail.com[173.194.79.108]:587, delay=4.8, delays=3.1/0.04/1.5/0.23, dsn=5.5.1, status=bounced (host smtp.gmail.com[173.194.79.108] said: 530-5.5.1 Authentication Required. Learn more at 530 5.5.1 http://support.google.com/mail/bin/answer.py?answer=14257 qh4sm3305629pac.8 - gsmtp (in reply to MAIL FROM command)) Here is my main.cf configuration, I tried a number of different options but nothing seems to work: alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases command_directory = /usr/sbin config_directory = /etc/postfix daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 2 html_directory = no inet_interfaces = localhost inet_protocols = ipv4 mail_owner = postfix mailq_path = /usr/bin/mailq.postfix manpage_directory = /usr/share/man mydestination = $myhostname, localhost.$mydomain, localhost myhostname = host.local.domain myorigin = $myhostname newaliases_path = /usr/bin/newaliases.postfix queue_directory = /var/spool/postfix readme_directory = /usr/share/doc/postfix-2.6.6/README_FILES relayhost = [smtp.gmail.com]:587 sample_directory = /usr/share/doc/postfix-2.6.6/samples sendmail_path = /usr/sbin/sendmail.postfix setgid_group = postdrop smtp_sasl_auth_enable = yes smtp_sasl_password_maps = hash:/etc/postfix/sasl_passwd smtp_sasl_security_options = noanonymous smtp_sasl_tls_security_options = noanonymous smtp_sasl_type = cyrus smtp_tls_CAfile = /etc/ssl/certs/ca-bundle.crt smtp_use_tls = yes smtpd_sasl_path = smtpd unknown_local_recipient_reject_code = 550 In the /etc/postfix/sasl_passwd files (sasl_passwd & sasl_passwd.db) I got the following (removed the real password, and replaced it with "password"): [smtp.google.com]:587 [email protected]:password To create the sasl_passwd.db file, I did that by running this command: postmap hash:/etc/postfix/sasl_passwd Do anybody got an idea why I can't seem to send an e-mail from the server? Kind Regards Alex

  Read the article

• Utility to optimally distribute files onto multiple DVDs?

  - by Alex R

  I have a bunch of media files which I want to record to DVD, but since each DVD only fits 4.5GB, I have to find the optimal way to organize the files to use the minimum number of DVDs (otherwise the empty space left in each DVD can easily add up). Are there any tools to help with this? Many years ago there was a DOS utility to do this with floppy disks.

  Read the article

• Flash drive suddenly died. Why? Can I recover it?

  - by mg

  Hi, I have a flash drive that I used not too much but, after few month of inactivity, it died. I know that flash drives have a limited write cycles but I am sure that this is not the problem. I tried to create a new partition table and format the drive nothing worked. This is the output of mkfs.ext2. marco@pinguina:~$ sudo LANG=en.UTF-8 mkfs.ext2 -v -c /dev/sdc1 [sudo] password for marco: mke2fs 1.41.11 (14-Mar-2010) fs_types for mke2fs.conf resolution: 'ext2', 'default' Calling BLKDISCARD from 0 to 4001431552 failed. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) Stride=0 blocks, Stripe width=0 blocks 244320 inodes, 976912 blocks 48845 blocks (5.00%) reserved for the super user First data block=0 Maximum filesystem blocks=1002438656 30 block groups 32768 blocks per group, 32768 fragments per group 8144 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Running command: badblocks -b 4096 -X -s /dev/sdc1 976911 badblocks: Input/output error during ext2fs_sync_device Checking for bad blocks (read-only test): done Block 0 in primary superblock/group descriptor area bad. Blocks 0 through 2 must be good in order to build a filesystem. Aborting.... Is there something I can do to recover it?

  Read the article

• windows 7 Libraries corruption

  - by Pablo

  I've provided an image to show the issue that im currently having. So basically the libraries work fine on windows explorer works fine, but trying to access from a browser, to upload file for example, the libraries just don't work they seem to be empty. Looking at the image, the window on the left is from the chrome browser and the windows on the right is from windows explorer. Image Link *Can't post images yet Any ideas? i've also tried creating new libraries with no luck.

  Read the article

• Fedora 15: em1 recently dissapeared and hostapd no longer serves internet to wirelessly connected devices

  - by Daniel K

  I have a laptop running hostapd, phpd, and mysql. This laptop uses an Ethernet connection to connect to the internet and acts as a wireless access point for my workplace's wifi devices. After installing some software and reconnecting my Ethernet elsewhere, my "em1" device is no longer present and wirelessly connected devices can no longer reach the internet. The software I recently installed is: pptp, pptpd, and updated some fedora libraries. I have also recently moved my desk and laptop to another location and thus had to reconnect the Ethernet elsewhere. Wifi devices no longer have access to the internet. Wirelessly connected devices are able to successfully log into the laptop, showing full strength, correct SSID, and uses the proper password. However, when I tried to connect to a site like google, the request times out. The device "em1" also no longer appears on my machine. Running: # ifup em1 will give me the following output: ERROR : [/etc/sysconfig/network-scripts/ifup-eth] Device em1 does not seem to be present, delaying initialization. And running: # dhclient em1 has the following output: Cannot find device "em1" When I run # dmesg|grep renamed, I get the following: renamed network interface eth0 to p4p1. I've tried to connect to the internet through p4p1 directly from the laptop and was successful. However, my wireless devices connected to my laptop are not able to connect to the internet. I have uninstalled pptp and pptpd using # yum erase ... but the problem still persists. To install pptp I used: # yum install pptp To install pptpd I did the following: # rpm -Uvh http://poptop.sourceforge.net/yum/stable/fc15/pptp-release-current.noarch.rpm # yum install pptpd To update my fedora libraries I used: # yum check-update # yum update EDIT: Running # route produces the following results: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 10.11.200.1 0.0.0.0 UG 0 0 0 p4p1 10.11.200.0 * 255.255.252.0 U 0 0 0 p4p1 172.16.100.0 * 255.255.255.0 U 0 0 0 wlan0

  Read the article

• converting to MXF using ffmpeg

  - by Prakash

  I have been trying to use FFmpeg utility to convert a avi file using DNxHD to mxf format. I am using "FFmpeg" with params as following: ffmpeg -i ccvt_box.avi -vcodec dnxhd -video_size 1920x1080 -r 24 -b:v 115m ex.mxf The error it is giving : ffmpeg version N-43737-g76c3fff Copyright (c) 2000-2012 the FFmpeg developers built on Aug 20 2012 18:50:42 with llvm-gcc 4.2.1 (LLVM build 2336.11.00) configuration: libavutil 51. 70.100 / 51. 70.100 libavcodec 54. 53.100 / 54. 53.100 libavformat 54. 25.104 / 54. 25.104 libavdevice 54. 2.100 / 54. 2.100 libavfilter 3. 11.101 / 3. 11.101 libswscale 2. 1.101 / 2. 1.101 libswresample 0. 15.100 / 0. 15.100 Input #0, avi, from 'ccvt_box.avi': Duration: 00:00:10.00, start: 0.000000, bitrate: 691 kb/s Stream #0:0: Video: indeo5 (IV50 / 0x30355649), yuv410p, 340x344, 10 tbr, 10 tbn, 10 tbc Metadata: title : bob.avi [dnxhd @ 0x7fcd60818e00] video parameters incompatible with DNxHD Output #0, mxf, to 'ex.mxf': Stream #0:0: Video: dnxhd, yuv422p, 340x344, q=2-1024, 90k tbn, 24 tbc Metadata: title : bob.avi Stream mapping: Stream #0:0 -> #0:0 (indeo5 -> dnxhd) Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height

  Read the article

• User http does not have write permissions directory?

  - by dwieeb

  I have a bit of an odd set up, I think. I have groups for each domain my server hosts, and I add the user http to each domain group along with the users that should have access to the groups' domains. In my php script running from a directory 'public_html', I try creating a file: <?php $output = ""; print exec('touch test 2>&1', $output); But I get touch: cannot touch `test': Permission denied and the file is not created. But here, clearly stated, the group has all permissions on the directory: drwxrwxr-x 5 dwieeb example.com 1024 Feb 4 05:19 public_html And here are the permissions on the php file in public_html that is trying to use the exec function: -rw-rw-r-- 1 dwieeb example.com 59 Feb 4 05:19 test.php How is this possible if http is part of the example.com group (as seen from a cat on /etc/group) and the directory has full permissions for the group? ... example.com:x:1000:dwieeb,http I'm stumped. EDIT (since apparently I'm not cool enough to answer my own questions yet): Ah, I found the problem. Yes, I restarted Nginx, but the php-fpm daemon must be restarted as well when http is added to the group for my domain. On Arch Linux: rc.d restart php-fpm

  Read the article

• Will Windows XP work on a Hybrid Hard Drive?

  - by Ben Torell

  I'm looking into getting the Seagate Momentus XT hybrid hard drive, and I'm planning on dual booting between Windows 7 and Windows XP. I know 7 and Vista have native support for taking advantage of the SSD portion of a hybrid drive, and I assume XP does not have any such support, but will XP still work on the drive? I would think it will, but I wanted to be sure, and the Googles are coming up empty for me on this one. Thanks!

  Read the article

• Trancoding a video with vlc and the MPEG-4 codec with a video bit rate

  - by Nicolas

  When I try to trancode a video with vlc using the MPEG-4 codec and a video bit rate, I get the following error : Either both buffer size and max rate or neither must be specified Here is the command line I used : vlc -vvv myvideo.m2ts --sout-ffmpeg-strict=-2 --sout '#transcode{vcodec=mp4v,vb=2000,acodec=mp4a,ab=96}:standard{access=file,mux=mp4,dst=/path/file.mp4}' It seems that I can't specify a video bit rate with the MPEG-4 codec. (If I remove the vb option, it works). So how can I specify a video bit rate with the MPEG-4 codec ?

  Read the article

• Using udev to create a character device based on a driver being loaded

  - by SteveCB

  I'm in the process of setting up RAID monitoring for a number of Dell servers that use the PERC 6i integrated card. We're using Nagios at present and the check_megasasctl plugin seems to fit the bill. However, the plugin relies upon the existence of: /dev/megaraid_sas_ioctl_node This device node doesn't exist by default, you have to create it by hand using something like: mknod /dev/megaraid_sas_ioctl_node c 253 0 Now, to make the existence of this device node persistent across reboots, I thought I could write a udev rule, but as usual, I'm missing something. I thought I could create a file such as /etc/udev/rules.d/10-local/rules that contained: DRIVER=="megasas" NAME="megaraid_sas_ioctl_node" MODE="0600" But this doesn't work - no device node after a reboot. Dmesg output indicates the megasas driver is loaded and functional: megasas: 00.00.04.01-RH1 Thu July 10 09:41:51 PST 2008 megasas: 0x1000:0x0060:0x1028:0x1f0c: bus 1:slot 0:func 0 megasas: FW now in Ready state Further, I don't see any means to instruct udev on which type of device node to create: character or block. I suspect I'm failing to understand exactly how udev is meant to work. I realise I could just cheat and run MegaCLI in /etc/rc.local, redirecting output to /dev/null; it creates the megaraid_sas_ioctl_node device node as part of its execution. I just thought using udev rules would be a) cleaner and b) a useful learning exercise. Perhaps I should just dump the above mknod command in /etc/rc.local... So how do I get udev to create the /dev/megaraid_sas_ioctl_node device node based on the presence of the megasas driver? Cheers Steve

  Read the article

• Is it possible to add tcp autotuning to windows xp?

  - by Caspin

  I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

  Read the article

• Is it possible to add tcp autotuning to windows xp?

  - by Caspin

  I have a network application that needs to send messages at 60 times a second. The messages are usually 300-400 bytes, but can be as large as 1500. The default setting for SO_SNDBUF is too small and limits the number of message that can be sent if the network latency is anything greater then 100ms. The naive solution is to just bump the SO_SNDBUF size to to something large. However, depending on the latency and the packet size that could be anywhere from 64K to 8MB. One of Vista's new features is TCP autotuning. Autotuning monitors the tcp connection and dynamically adjust the buffer sizes to allow for optimal communication. I would like to use auto tuning on our windows xp machine so I don't need to guess what my buffers sizes should be. Is there a way to install either a microsoft or 3rd party tcp autotuner on windows xp?

  Read the article

• Hard Disk Not Counting Reallocated Sectors

  - by MetaNova

  I have a drive that is reporting that the current pending sectors is "45". I have used badblocks to identify the sectors and I have been trying to write zeros to them with dd. From what I understand, when I attempt writing data directly to the bad sectors, it should trigger a reallocation, reducing current pending sectors by one and increasing the reallocated sector count. However, on this disk both Reallocated_Sector_Ct and Reallocated_Event_Count raw values are 0, and dd fails with I/O errors when I attempt to write zeros to the bad sectors. dd works fine, however, when I write to a good sector. # dd if=/dev/zero of=/dev/sdb bs=512 count=1 seek=217152 dd: error writing ‘/dev/sdb’: Input/output error Does this mean that my drive, in some way, has no spare sectors to be used for reallocation? Is my drive just in general a terrible person? (The drive isn't actually mine, I'm helping a friend out. They might have just gotten a cheap drive or something.) In case it is relevant, here is the output of smartctl -i : Model Family: Western Digital Caviar Green (AF) Device Model: WDC WD15EARS-00Z5B1 Serial Number: WD-WMAVU3027748 LU WWN Device Id: 5 0014ee 25998d213 Firmware Version: 80.00A80 User Capacity: 1,500,301,910,016 bytes [1.50 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 3.0 Gb/s Local Time is: Fri Oct 18 17:47:29 2013 CDT SMART support is: Available - device has SMART capability. SMART support is: Enabled UPDATE: I have run shred on the disk, which has caused Current_Pending_Sector to go to zero. However, Reallocated_Sector_Ct and Reallocated_Event_Count are still zero, and dd is now able to write data to the sectors it was previously unable to. This leads me with several other questions: Why aren't the reallocations being recored by the disk? I'm assuming the reallocation took place as I can now write data directly to the sector and couldn't before. Why did shred cause reallocation and not dd? Does the fact that shred writes random data instead of just zeros make a difference?

  Read the article

• Gifsicle: How to set it to not overwrite the original GIF file if the resulting modified GIF file is larger than the original?

  - by galacticninja

  About Gifsicle: Gifsicle is a command-line tool for creating, editing, and getting information about GIF images and animations. One of its features is (from its website): Optimize your animations! This stores only the changed portion of each frame, and can radically shrink your GIFs. You can also use transparency to make them even smaller. Gifsicle’s optimizer is pretty powerful, and usually reduces animations to within a couple bytes of the best commercial optimizers. I call Gifsicle through this .BAT file in the Right Click - 'Send to' Menu: @echo off :compressFile "C:\Programs\Compression Scripts\gifsicle\bin\gifsicle.exe" --batch -V -O3 %1% echo. echo. SHIFT if exist %1% goto compressFile PAUSE This animated GIF file, however: http://i.minus.com/i7WdodY5Zwot3.gif, when its compression is optimized with Gifsicle with the above commands, results in a larger-filesized GIF file. Gifsicle overwrites the original GIF file with the resulting larger-filesized GIF file. Initial filesize: 7.57 MiB (7,942,886 bytes). After running through the above commands with Gifsicle: 7.64 MiB (8,017,622 bytes). Is there a way to prevent Gifsicle from overwriting the original file if its output file is larger than the original file, while still overwriting the original file if the output file is smaller? Details: OS: Windows 7 Gifsicle version: 1.63, from the binary provided here: http://www.lcdf.org/gifsicle/ Gifsicle manual

  Read the article

• Best grep-like tool

  - by e-satis

  I do in file search a lot, and used to love grep. Then I learn the existence of egrep, so I switched to benefit from the advanced regexp. Then I discovered the Eclipse search tool. Much easier to use that grep. Then I found ack : fast, easy, powerful. And now I use grin, which is smooth for pythonistas. I know there is also a couple of this kind of tools with a GUI. So what tool do you use, and why do you think it's the best. Practical features generally are : fast to fire and use; speedy processing; automatically ignore useless files; colored output; output lines, filename, context; allow complex regexp; allow a custom filtering and ouput; GUI + command line intergation; let you open an editor from the result set. There are some related posts on SO : http://stackoverflow.com/questions/87350/what-are-good-grep-tool-for-windows http://stackoverflow.com/questions/981601/colorized-grep-viewing-the-entire-file-with-highlighting http://stackoverflow.com/questions/1028107/is-there-some-unix-util-that-will-allow-me-to-grep-multiple-files-with-little-type http://stackoverflow.com/questions/1027906/unix-find-grep-syntax-vs-awk

  Read the article

< Previous Page | 371 372 373 374 375 376 377 378 379 380 381 382  | Next Page >