Search Results

Search found 17749 results on 710 pages for 'connection pool'.

Page 376/710 | < Previous Page | 372 373 374 375 376 377 378 379 380 381 382 383  | Next Page >

• Cisco Routing through VPN

  - by Superman

  I am looking for a way to allow a client Win7 computer, which connects to our California office's Cisco ASA 5510 over an IPSec VPN connection to then be able to connect to a computer in our chicago office which is itself connected through another Cisco ASA router to california. It appears that we are unable to route client vpn connections between each other, and I cannot find any guidance on how to enable this. Let me know if this is possible / what needs to be done.

  Read the article

• How to get an unprivileged public status page showing in OpenWrt 12.09 or newer?

  - by lkraav

  For the use case where the WAN connection goes down, but employees can still access wifi, I'd like them to be able to check on some sort of a public router status page in their problem reports. This may have been available on DD-WRT at one point (or still is), I can't 100% recall anymore. Going through all LuCI's screens with a fine-toothed comb and googling a fair amount isn't producing results. Anyone have a solution?

  Read the article

• virtual machine doesn't recognise ip of the Machine it run on

  - by Muky

  Hi I am using virtualBox to create a virtual XP machine on my XP using Bridge connection. From my VM I am able to ping to any other IP on the network except for the IP which the VM is run on. any idea?

  Read the article

• Why is my SSH session timing out in less than a minute?

  - by John Smith

  Within a minute of connecting to my remote Linux server through SSH, my session times out and I cannot contact the server until a few seconds have passed. Meanwhile, I'm connected to other servers without interruption. This is only happening when I establish connection from an hotel wireless AP. When I connect from my phone's Internet, the problem does not occur. Does anyone know what might be causing these unusual timeouts?

  Read the article

• Cisco 1242 WAP Bridging

  - by DanWake

  I'm looking to connect two facilities with a a pair of Cisco 1242 access points and am looking for advice on configuration. We have multiple VLANs running that will need to be passed through the connection, but otherwise a fairly simple setup. Any advice on best practices from security, reliability, and speed points of views?

  Read the article

• Improve file transfer speed between Windows PCs and servers

  - by Geotarget

  I've setup a server which I've connected to multiple PCs in my workplace. Sadly, data transfer speeds are at max 3 MB/sec per connection which works out slow for file transfers, especially when transferring large files. I'm using Windows filesharing and the server is a Windows Server 2008 (2 Ghz CPU, 1 GB RAM) and the client PCs mostly running Windows 7. How can I detect bottlenecks in my network and improve file sharing speed within the network?

  Read the article

• PHP ssh2_fingerprint() does not match ssh-keygen -lf id_rsa.pub

  - by Justin

  I am using the lib ssh2 module with PHP and calling the function ssh2_fingerprint() to get the keys fingerprint. According to all resources on the internet, I can get the fingerprint of a public key by executing: ssh-keygen -lf id_rsa.pub Which outputs something like: 2048 d4:41:3b:45:00:49:4e:fc:2c:9d:3a:f7:e6:6e:bf:e7 id_rsa.pub (RSA) However, when I call ssh2_fingerprint($connection, SSH2_FINGERPRINT_HEX) in PHP with the same public key I get: dddddba52352e5ab95711c10fdd56f43 Shouldn't they match? What am I missing?

  Read the article

• are you supposed to be able to "ping" specific pages of websites, or just the domain name?

  - by Bec

  (sorry, i think my jargon is a bit off there, not sure) I'm trying to work out what's going on with my podcasts not downloading properly, to see whether it was my pod-catching software or the connection i tried doing a ping on the podcast URL e.g. www.abc.net.au/rn/podcast/feeds/ockham.xml and it failed (i got "could not find host"), it works for the first part of it though www.abc.net.au I can get to the xml page in a web browser though, and ping doesn't work on the podcasts which have been downloading right either.

  Read the article

• Automatically restore windows network drive (red "X") via batch file

  - by user33958

  i need check if a network drive is mapped and accessible. From time to time windows displays a red X on the drive, and i would need to manually click the drive in explorer to reconnect. I already found solutions which involve editing the registry which unfortunately isn´t possible. So i would need a batch file checking for connection, and (re-)mounting the drive. What i´m using at the moment: IF NOT EXIST z: net use z: \\10.211.55.5\test

  Read the article

• PHP ftp_connect

  - by Dude Lebowski

  I try to use the php ftp_connect fucntion on my dedicated server and I'm unable to establish a connection: $conn_id = ftp_connect($ftp_server, 21) or die("Unable to connect to $ftp_server") ; I'm sure the function is available as I test with : function_exists('ftp_connect') and it returns true When I ftp the server through the shell I can reach it so I guess it's not a firewall issue. Am I missing something else ? Thanks for your precious advices

  Read the article

• Routing between 2 different subnets on 2 different interfaces in SonicOS

  - by Chris1499

  I'm having a bit of a problem allowing traffic between two of my subnets. Here's the structure I've built. The X0 interface has our windows server on it and it handles DHCP/DNS, etc. X1 has the WAN connection. The Sonicwall is handling DHCP on X2. The X3 interface is connected to a different vlan on the 48 port switch. The Sonicwall is handling DHCP on this network as well. So here's what i want to do. The network on X2 is for our guest wireless; i don't want it to be able to access any of the other networks, just the internet, so i that all blocked in the firewall. No issues there. The X3 network is going to be for programmable controllers, and needs to be able to access the X0 network where our computers are. This is where my problem is. I'm not able to get between the 192.168.2.xxx and the 192.168.1.xxx on interfaces X0 and X3 respectively. I have these rules set up in the firewall. The Lan Primary Subnet is the 192.168.2.0 on X0. So if i'm not mistaken, this will allow traffic between the two through the firewall. Now this is where I'm a little confused. Do i need to use NAT to get the traffic from X0 to go to X3 (and vice versa), or a static route, or both? Currently i have both, though i doubt they're done correctly (also in screenshot). I've tried to ping between the two without luck. Any advice, or if you see what's wrong with my setup, is much appreciated. If you need some more information, let me know. Thanks all! EDIT: So i found that i don't neither either NAT or a static route, that the setting in the firewall is enough. I can now ping from the 192.168.1.xxx network, however i can't access the server on the 192.168.2.xxx network. When i try to access i get "An error occured while reconnecting to Z: to server Microsoft Windows Network: The local device name is already in use. This connection has not been restored. What am i missing?

  Read the article

• Windows Firewall + FTP Server on WS03

  - by kovu

  Hi, my OS is Windows Server 2003. I installed the FTP Service and configure it with the IIS 6.0 Console. When I deactivate my firewall, all its okay, but when not, I can't get a connection. Port 21 tcp + udp, port 22 tcp + udp and the whole FTP-Server Application is set as go trouhgt, but don't work. Of course, the FTP ruins on 21. Any ideas

  Read the article

• KVM-Guest does not boot: qemudParsePCIDeviceStrs

  - by markus

  I have a Server running Ubuntu 10.10 Server-Edition kvm, and libvirt (both ubuntu-native packages) HDD-Partitioning was done with LVM. Then I created some VMs with Virt-Manager and assigned LVM-Volumes to the VMs. Now the VMs do not boot. Virt-Manager shows a CPU-Usage of 100% for this Guest and the VNC-Connection states Booting from Hard Disk The VM-specific logfiles do not show any abnormality only syslog shows a warning warning : qemudParsePCIDeviceStrs:1422 : Unexpected exit status '1', qemu probably failed What can I do to find the error?

  Read the article

• unknown reciever Esmtp

  - by Morteza Soltanabadiyan

  I found this in my log server: sm-mta[11410]: r9BKb6YY021119: to=<[email protected]>, ctladdr=<[email protected]> (33/33), delay=2+07:24:18, xdelay=00:00:01, mailer=esmtp, pri=29911032, relay=mail1.mkuku.com. [58.22.50.83], dsn=4.0.0, stat=Deferred: Connection refused by mail1.mkuku.com. This message is repeated every 10-30 seconds with a different "to" address. What is this? Is my server being used to send spam?

  Read the article

• Sharing a USB wireless-g adaptor between two computers

  - by cornjuliox

  I've got two computers here that need to connect via wireless-g usb adapter to the same network for internet access but only one USB adapter. Both PCs are using Windows XP, and I have no crossover cables. I've got both computers wired up to a router, and the PC with the active internet connection has ICS enabled, but the second PC gets no internet. Any ideas?

  Read the article

• Windows Firewall + FTP Servier on WS03

  - by kovu

  Hi, my OS is Windows Server 2003. I installed the FTP Service and configure it with the IIS 6.0 Console. When I deactivate my firewall, all its okay, but when not, I can't get a connection. Port 21 tcp + udp, port 22 tcp + udp and the whole FTP-Server Application is set as go trouhgt, but don't work. Of course, the FTP ruins on 21. Any ideas

  Read the article

• Configuring an EH-WIC Card on Cisco 1941 Router

  - by Olanrewaju T

  I have a Cisco 1941 Router that has just two ports for Gigabit connection but wanted more so I got a four port Cisco EH-WIC Card and connected it to it. I have been trying to assign IP address to the port GigabitEtnernet 0/0/0 because I have a cable already connected to it whose device I want it facing the router directly because I dont want to NAT its address. I want to assign the physical address on the port. Kinldy help if you understand what I am saying. Regards

  Read the article

• Nautilus cannot handle "sftp" locations via x11

  - by blockhead

  I'm logging into my home computer (Ubuntu 10.04) via ssh, and now I want to open a remote connection (one that is stored in my bookmarks). Nautilus tells me "Nautilus cannot handle "sftp" locations via x11". Why might this be?

  Read the article

• How to connect laptop with telephone using WI-FI? (ethernet)

  - by rmaster

  What I did: 1)added new wireless network in wireless network settings and gave it SSID 2)gave laptop the IP like 192.168.0.1, mask: 255.255.255.0, gateway: 192.168.0.2 3)gave the telephone with wifi the same mask but IP and gateway rewersed But telephone can not find my new wireless network(it can find all other networks), computer also can not find it. where is error? how to make it visible and working? if my steps are wrong tell me correct way to establish this connection via wi-fi

  Read the article

• How to transfer files from windows 7 pc to vista

  - by Samuel C

  Tried using direct connection using Ethernet cable and using windows easy transfer, but no luck, also tried using ad-hoc, home group, and connecting through a router both wired and wireless but no luck, im getting a little frustrated as I need to transfer these files because im selling one of them this afternoon! All I need to do is transfer some documents and files. The windows 7 pc recognizes the vista pc but vista cant recognize the win 7.

  Read the article

• PPPoA Half Bridge Modems

  - by petebob796

  I am looking for a simple ADSL ethernet modem to plug into a DIR-825 router. Anyone know of one, it's for a PPPoA connection so I believe I need something capable of half bridge/zipb.

  Read the article

• HOw to enable shell login for particular user in one ip

  - by Master

  I have blocked FTP 21 port on server. NOw every connection will be via SFTP via ssh. Initially i had /etc/hosts.deny -- sshd:all But i had to remove that otherwise sftp was not working. How can i secure my shell login so that if someone login via root or userbac(root previleges) Then i need private key but not for other users Or any other to secure my system Thanks

  Read the article

• How come I can't redirect TCP ports on this wireless router?

  - by George Edison

  I am configuring a router to redirect TCP port 5900 (yes, this is for VNC) to a specific IP address on the network. Here is what I have: From a local computer on the same network, I can telnet to 192.168.1.64 (port 5900) just fine. However, when trying to telnet to the machine (port 5900) using its external IP address, it doesn't work. (The connection times out.) The router is a Gigaset SE567, if that helps.

  Read the article

• How to open port 25 on the server

  - by liuxingruo

  I'm using centOS. I want to implement a smtp mail server, and I have installed postfix and dovecot(both have been set correctly). I tried to telnet the 25 port, but it returns Unable to connect to remote host: Connection refused So, How can I open the 25 port? Thanks!

  Read the article

• Windows 7 & Virtual PC and Internet (gateway) problems on host PC

  - by Mufasa

  I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

  Read the article

< Previous Page | 372 373 374 375 376 377 378 379 380 381 382 383  | Next Page >