Search Results

Search found 21955 results on 879 pages for 'self host'.

Page 381/879 | < Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >

• ESXi Guests will not boot on IBM x3550 M3

  - by Adrian

  I have a problem with Guests not booting under VMWare ESXi 5.0 on my IBM x3550M3 server. VM Host Server: IBM x3550 M3 7944AC1 server w/ 2x Intel Xeon E5607 2.27Ghz CPUs ESXi 5.0.0 Build 623860, built for IBM Hardware downloaded from IBM Storage: 2x500GB SAS local storage 8GB RAM Vt is verified to be ENABLED Server Health Status: Normal The ESXi host boots just fine. The Client connects just fine. Guests can be configured but do not successfully boot. The initial guest memory consumption jumps up to 560MB and drops down to 40MB after a few seconds. Initial CPU usage is 1 full CPU (3000Ghz per the chart) and immediately drops downm to 29Mhz. Guests do not display any output in the Console tab but show a state of 'Powered On'. VMs are listed as Version 7 and the behavior is duplicated across all availabled Guest OS flavors. Problem also duplicated when server is booted up in Legacy Only mode. Logs do not contain anything particularly suspucious. Edit: No firewalls, routers, or VLANs in between the client and server. Edit 2: We have tried to Boot Guest into BIOS screen at Next Boot checkbox in the Guest Setting. Was not successful. Edit 3: 500GB datastore with 1 40GB VM on it. Plenty of space.

  Read the article

• Add IPv6 support to DirectAdmin server

  - by George Boot

  I just set up an new DirectAdmin, and I want to prepare it for IPv6 use. My ISP have gave me an range of IPv6 addresses that I can use. Lets say that address is 2a01:7c8:**:1f::. My neworkadapter user DHCP to resolves its IP-addresses. When i type ifoncig eth0 I get the following result: eth0 Link encap:Ethernet HWaddr 52:**:**:**:ce:f3 inet addr:37.**.**.44 Bcast:37.**.**.255 Mask:255.255.255.0 inet6 addr: 2a01:7c8:****:1f::/64 Scope:Global inet6 addr: fe80::5054:ff:fe87:cef3/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:38941 errors:0 dropped:0 overruns:0 frame:0 TX packets:29439 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:3779534 (3.6 MiB) TX bytes:5089379 (4.8 MiB) As you can see, I have an IPv6 address set, but I can't ping6 an IPv6 host. I get the error: connect: Network is unreachable. I decided that I needed an gateway, so I tryed to add one: ip -6 route add default via 2a01:7c8:****::1 dev eth0 (2a01:7c8:**::1 is the gateway of my ISP). But it trows an error: RTNETLINK answers: No route to host. Does somebody know what to do, and how to solve this issue? Thanks a lot!

  Read the article

• Why Virtual Box won't give me option to create 64 bits guests?

  - by Eduardo Born

  My host is x64 bits Windows 8.1. I downloaded the latest Virtual Box (4.3) and I'm trying to create a VM with a 64 bits Ubuntu OS (ubuntu-12.04.3-desktop-amd64). When I go to New VM wizard, it doesn't give me option to select "Ubuntu (x64)" as I have seen in other people's screenshots, only just "Ubuntu". As a result, the ISO can't boot. I tried in another PC and Virtual Box gives the x64 variants to most listed OS... Control Panel shows x64 OS, x64 processor. My host laptop is a Sony Vaio VPCZ22UGX/N, Intel® Core™ i7-2640M processor. CPUz shows Vx-t is available on my processor, of course. Here is what I tried so far: I enabled IO APIC as required in the docs. I have virtualization enabled in the BIOS. It works fine in VMware. Check that Hyper-V is not running or even installed on my Windows. Same for VMware. I also tried running the command: VBoxManage modifyvm [vmname] --longmode on for that VM, but no change.. I think the issue is really that I can't select x64 variant of the Ubuntu OS for that VM. Other people seem to indicate that's a requirement, but I don't get that option for some reason. I spent a lot of time and can't find what's wrong... Anyone knows what could be missing here? Thank you very much!! Eduardo

  Read the article

• nginx: SSI working on Apache backend, but not on gunicorn backend

  - by j0nes

  I have nginx in front of an Apache server and a gunicorn server for different parts of my website. I am using the SSI module in nginx to display a snippet in every page. The websites include a snippet in this form: For static pages served by nginx everything is working fine, the same goes for the Apache-generated pages - the SSI include is evaluated and the snippet is filled. However for requests to my gunicorn backend running a Python app in Django, the SSI include does not get evaluated. Here is the relevant part of the nginx config: location /cgi-bin/script.pl { ssi on; proxy_pass http://default_backend/cgi-bin/script.pl; include sites-available/aspects/proxy-default.conf; } location /directory/ { ssi on; limit_req zone=directory nodelay burst=3; proxy_pass http://django_backend/directory/; include sites-available/aspects/proxy-default.conf; } Backends: upstream django_backend { server dynamic.mydomain.com:8000 max_fails=5 fail_timeout=10s; } upstream default_backend { server dynamic.mydomain.com:80; server dynamic2.mydomain.com:80; } proxy_default.conf: proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; What is the cause for this behaviour? How can I get SSI includes working for my pages generated on gunicorn? How can I debug this further?

  Read the article

• vDS - vCenter Problem

  - by rbmadison

  We are implementing a vSphere farm and are using a distrubuted switch. The VC is a VM within the farm connected to the distrubuted switch. We had a SAN issue and all of our VMs were down. When the SAN recovered and we restarted the ESX host containing the VC the VC couldn't connect to the network through the vDS. We had to remove a NIC from the vDS on that host and create a regular vswitch and then connect the VC to that before the VC would connect to the network. Is this typical behavior? If the VC goes down does all vDS networking stop on all the hosts? That seems to be a very bad thing. I thought networking would work even though the VC is down because the hosts have the vDS configuration cached. Is there a better way to configure it to prevent this from happening. We want to keep the VC as a VM for HA and recoverabilty purposes. Can anyone offer suggestions or explanations? I appreciate the help. Thanks, Rick

  Read the article

• BackupPC - why does it use rsync --sender --server ... ?

  - by Jakobud

  I'm in the process of experimenting with BackupPC on a CentOS 5.5 server. I have everything pretty much setup with default values. I tried setting up a basic backup for a host's /www directory. The backup fails with the following errors: full backup started for directory /www Running: /usr/bin/ssh -q -x -l root target /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Xfer PIDs are now 30395 Read EOF: Connection reset by peer Tried again: got 0 bytes Done: 0 files, 0 bytes Got fatal error during xfer (Unable to read 4 bytes) Backup aborted (Unable to read 4 bytes) Not saving this as a partial backup since it has fewer files than the prior one (got 0 and 0 files versus 0) First of all, yes I have my ssh keys setup to allow me to ssh to the target server without requiring a password. In the process of troubleshooting, I tried the above ssh command directly from the command line, and it hangs. Looking at the end of the debug messages for SSH I get: debug1: Sending subsystem: /usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/ Request for subsystem '/usr/bin/rsync --server --sender --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive --ignore-times . /www/' failed on channel 0 Next I started looking at the rsync flags. I did not recognize --server and --sender. Looking at the rsync man pages, sure enough, I don't see anything about --server or --sender in there. What are those in there for? Looking at the BackupPC config I have this: RsyncClientPath = /usr/bin/rsync RsyncClientCmd = $sshPath -q -x -l root $host $rsyncPath $argList+ And for the arguments, I have the following listed: --numeric-ids --perms --owner --group -D --links --hard-links --times --block-size=2048 --recursive Notice there is no --server, --sender or --ignore-times. Why are these things getting added in? Is this part of the problem?

  Read the article

• Can't connect to Synology DiskStation through HTTPS when using Windows 7 Import

  - by LeonidasFett

  a little background to my problem: I have a Synology DiskStation 213j that I use as a backup/data storage solution. When I'm at work, I would like to push and pull files from my DiskStation but I can't use VPN which is forbidden for outgoing connections. So I wanted to try to use HTTPS so I can at least connect securely to the web interface. I mostly use Chrome which uses the Windows Certificate Store. So I tried importing a self-signed certificate into it, without success. I still get a warning in Chrome telling me the connection is not secure because it can't be verified. When I import the certificate into Firefox though, it works and I can connect through HTTPS. I checked my domain on this site: http://www.sslshopper.com/ssl-checker.html It shows no errors, only a warning that the certificate is self-signed. Which is OK in this case. Any got any idea why importing the certificate into Windows 7 doesn't work? I tried Right-Click domain.mydomain.de.crt File --> Install certificate --> Next --> both options here (in case of "Place certificate in following store:" I selected "Third Party Root Certificate Authorities") to no avail.

  Read the article

• Kernel Logging disabled?

  - by Tiffany Walker

  uname -a Linux host 2.6.32-279.9.1.el6.i686 #1 SMP Tue Sep 25 20:26:47 UTC 2012 i686 i686 i386 GNU/Linux And start ups: ls /etc/init.d/ abrt-ccpp certmonger dovecot irqbalance matahari-broker mdmonitor nfs proftpd rpcbind single ypbind abrtd cgconfig functions kdump matahari-host messagebus nfslock psacct rpcgssd smartd abrt-oops cgred haldaemon killall matahari-network mysqld ntpd qpidd rpcidmapd sshd acpid cpuspeed halt ktune matahari-rpc named ntpdate quota_nld rpcsvcgssd sssd atd crond httpd lfd ma tahari-service netconsole oddjobd rdisc rsyslog sysstat auditd csf ip6tables lvm2-lvmetad matahari-sysconfig netfs portreserve restorecond sandbox tuned autofs cups iptables lvm2-monitor matahari-sysconfig-console network postfix rngd saslauthd udev-post But when I installed CSF/LFD I am getting nothing. LFD does not create lfd.log and nor are any blocks being logged in /var/log/messages either from the firewall. This is not natural. I looked for klogd but maybe I am looking in the wrong place for it to see if it is enabled? ls /etc/init.d/syslog ls: cannot access /etc/init.d/syslog: No such file or directory Also noticed no syslog? Also noticed this: csf -d 84.113.21.201 Adding 84.113.21.201 to csf.deny and iptables DROP... iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. I've never seen this before and this is a dedicated box. Also: ./csftest.pl Testing ip_tables/iptable_filter...OK Testing ipt_LOG...OK Testing ipt_multiport/xt_multiport...OK Testing ipt_REJECT...OK Testing ipt_state/xt_state...OK Testing ipt_limit/xt_limit...OK Testing ipt_recent...OK Testing xt_connlimit...OK Testing ipt_owner/xt_owner...OK Testing iptable_nat/ipt_REDIRECT...OK Testing iptable_nat/ipt_DNAT...OK RESULT: csf should function on this server iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination Chain FORWARD (policy ACCEPT) target prot opt source destination Chain OUTPUT (policy ACCEPT) target prot opt source destination

  Read the article

• Nagios command not transmitting all arguments

  - by markus

  I'm using the following service to monitor our postgres db from nagios: define service{ use test-service ; Name of servi$ host_name DEMOCGN002 service_description Postgres State check_command check_nrpe!check_pgsql!192.168.1.135!test!test!test notifications_enabled 1 } On the remote machine I've configured the command: command[check_pgsql]=/usr/lib/nagios/plugins/check_pgsql -H $ARG1$ -d $ARG2$ -l $ARG3$ -p $ARG4$ In the syslog I can see that command is executed, but there is only one argument transmitted: Oct 20 13:18:43 DEMOSRV01 nrpe[1033]: Running command: /usr/lib/nagios/plugins/check_pgsql -H 192.168.1.134 -d -l -p Oct 20 13:18:43 DEMOSRV01 nrpe[1033]: Command completed with return code 3 and output: check_pgsql: Database name is not valid - -l#012Usage:#012check_pgsql [-H <host>] [-P <port>] [-c <critical time>] [-w <warning time>]#012 [-t <timeout>] [-d <database>] [-l <logname>] [-p <password>] Oct 20 13:18:43 DEMOSRV01 nrpe[1033]: Return Code: 3, Output: check_pgsql: Database name is not valid - -l#012Usage:#012check_pgsql [-H <host>] [-P <port>] [-c <critical time>] [-w <warning time>]#012 [-t <timeout>] [-d <database>] [-l <logname>] [-p <password>] Why are arguments 2,3 and 4 missing?

  Read the article

• Apahe configuration with virtual hosts and SSL on a local network

  - by Petah

  I'm trying to setup my local Apache configuration like so: http://localhost/ should serve ~/ http://development.somedomain.co.nz/ should serve ~/sites/development.somedomain.co.nz/ https://development.assldomain.co.nz/ should serve ~/sites/development.assldomain.co.nz/ I only want to allow connections from our local network (192.168.1.* range) and myself (127.0.0.1). I have setup my hosts file with: 127.0.0.1 localhost 255.255.255.255 broadcasthost ::1 localhost fe80::1%lo0 localhost 127.0.0.1 development.somedomain.co.nz 127.0.0.1 development.assldomain.co.nz 127.0.0.1 development.anunuseddomain.co.nz My Apache configuration looks like: Listen 80 NameVirtualHost *:80 <VirtualHost development.somedomain.co.nz:80> ServerName development.somedomain.co.nz DocumentRoot "~/sites/development.somedomain.co.nz" DirectoryIndex index.php <Directory ~/sites/development.somedomain.co.nz> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <VirtualHost localhost:80> DocumentRoot "~/" ServerName localhost <Directory "~/"> Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> <IfModule mod_ssl.c> Listen *:443 NameVirtualHost *:443 AcceptMutex flock <VirtualHost development.assldomain.co.nz:443> ServerName development.assldomain.co.nz DocumentRoot "~/sites/development.assldomain.co.nz" DirectoryIndex index.php SSLEngine on SSLCipherSuite ALL:!ADH:!EXPORT56:RC4+RSA:+HIGH:+MEDIUM:+LOW:+SSLv2:+EXP:+eNULL SSLCertificateFile /Applications/XAMPP/etc/ssl.crt/server.crt SSLCertificateKeyFile /Applications/XAMPP/etc/ssl.key/server.key BrowserMatch ".*MSIE.*" \ nokeepalive ssl-unclean-shutdown \ downgrade-1.0 force-response-1.0 <Directory ~/sites/development.assldomain.co.nz> SSLRequireSSL Options Indexes FollowSymLinks ExecCGI Includes AllowOverride All Order allow,deny Allow from all </Directory> </VirtualHost> </IfModule> http://development.somedomain.co.nz/ http://localhost/ and https://development.assldomain.co.nz/ work fine. The problem is when I request http://development.anunuseddomain.co.nz/ or http://development.assldomain.co.nz/ it responds with the same as http://development.somedomain.co.nz/ I want it to deny all requests that do not match a virtual host server name and all requests to a https host that are requested with http PS I'm running XAMPP on Mac OS X 10.5.8

  Read the article

• postfix is unable to send emails to external domains

  - by BoCode

  Whenever i try to send an email from my server, i get the following error: Nov 13 06:37:21 xyz postfix/smtpd[6730]:connect from unknown[a.b.c.d] Nov 13 06:37:21 xyz postfix/smtp[6729]: warning: host X.com[x.y.z.d]:25 greeted me with my own hostname xyz.biz Nov 13 06:37:21 xyz postfix/smtp[6729]: warning: host X.com[x.y.z.d]:25 replied to HELO/EHLO with my own hostname xyz.biz Nov 13 06:37:21 xyz postfix/smtp[6729]: 2017F1B00C54: to=<[email protected]>, relay=X.com[x.y.z.d]:25, delay=0.98, delays=0.17/0/0.81/0, dsn=5.4.6, status=bounced (mail for X.com loops back to myself) this is the output of postconf -n: address_verify_poll_delay = 1s alias_database = hash:/etc/aliases alias_maps = body_checks_size_limit = 40980000 command_directory = /usr/sbin config_directory = /etc/postfix connection_cache_ttl_limit = 300000s daemon_directory = /usr/libexec/postfix data_directory = /var/lib/postfix debug_peer_level = 1 debugger_command = PATH=/bin:/usr/bin:/usr/local/bin:/usr/X11R6/bin ddd $daemon_directory/$process_name $process_id & sleep 5 default_delivery_slot_cost = 2 default_destination_concurrency_limit = 10 default_destination_recipient_limit = 1 default_minimum_delivery_slots = 3 default_process_limit = 10000 default_recipient_refill_delay = 1s default_recipient_refill_limit = 10 disable_dns_lookups = yes enable_original_recipient = no hash_queue_depth = 2 home_mailbox = Maildir/ html_directory = no in_flow_delay = 0 inet_interfaces = all inet_protocols = ipv4 initial_destination_concurrency = 100 local_header_rewrite_clients = mail_owner = postfix mailq_path = /usr/bin/mailq manpage_directory = /usr/share/man master_service_disable = milter_default_action = accept milter_protocol = 6 mydestination = $myhostname, localhost.localdomain, localhost, $mydomain mydomain = xyz.biz myhostname = xyz.biz mynetworks = 168.100.189.0/28, 127.0.0.0/8 myorigin = $mydomain newaliases_path = /usr/bin/newaliases non_smtpd_milters = $smtpd_milters qmgr_message_active_limit = 500 qmgr_message_recipient_limit = 500 qmgr_message_recipient_minimum = 1 queue_directory = /var/spool/postfix queue_run_delay = 300s readme_directory = /usr/share/doc/postfix.20.10.2/README_FILE receive_override_options = no_header_body_checks sample_directory = /usr/share/doc/postfix.2.10.2/examples sendmail_path = /usr/sbin/sendmail service_throttle_time = 1s setgid_group = postdrop smtp_always_send_ehlo = no smtp_connect_timeout = 1s smtp_connection_cache_time_limit = 30000s smtp_connection_reuse_time_limit = 30000s smtp_delivery_slot_cost = 2 smtp_destination_concurrency_limit = 10000 smtp_destination_rate_delay = 0s smtp_destination_recipient_limit = 1 smtp_minimum_delivery_slots = 1 smtp_recipient_refill_delay = 1s smtp_recipient_refill_limit = 1000 smtpd_client_connection_count_limit = 200 smtpd_client_connection_rate_limit = 0 smtpd_client_message_rate_limit = 100000 smtpd_client_new_tls_session_rate_limit = 0 smtpd_client_recipient_rate_limit = 0 smtpd_delay_open_until_valid_rcpt = no smtpd_delay_reject = no smtpd_discard_ehlo_keywords = silent-discard, dsn smtpd_milters = inet:127.0.0.1:8891 smtpd_peername_lookup = no unknown_local_recipient_reject_code = 550 what could be the issue?

  Read the article

• tcp msl timeout

  - by iamrohitbanga

  The following is given in the book TCP IP Illustrated by Stevens Quiet Time Concept The 2MSL wait provides protection against delayed segments from an earlier incarnation of a connection from being interpreted as part of a new connection that uses the same local and foreign IP addresses and port numbers. But this works only if a host with connections in the 2MSL wait does not crash. What if a host with ports in the 2MSL wait crashes, reboots within MSL seconds, and immediately establishes new connections using the same local and foreign IP addresses and port numbers corresponding to the local ports that were in the 2MSL wait before the crash? In this scenario, delayed segments from the connections that existed before the crash can be misinterpreted as belonging to the new connections created after the reboot. This can happen regardless of how the initial sequence number is chosen after the reboot. To protect against this scenario, RFC 793 states that TCP should not create any connections for MSL seconds after rebooting. This is called the quiet time Few implementations abide by this since most hosts take longer than MSL seconds to reboot after a crash. Do operating systems wait for 2MSL seconds now after a reboot before initiating a TCP connection. The boot times are also less these days. Although the ports and sequence numbers are random but is this wait implemented in Linux?

  Read the article

• Local DNS and Apache Server Configuration Interferring - example.com / www.example.com

  - by nicorellius

  I have a domain for my site: example.com I am also running local DNS with these lines: www IN CNAME server.<host_provider>.com. dev IN CNAME server.<host_provider>.com. So www.example.com and dev.example.com go to production and development sites, respectively, that are hosted by a host company. In my Apache configuration for the main site, I'm running a rewrite rule like this: RewriteEngine ON RewriteCond %{HTTP_HOST} ^example\.com$|!dev\.example\.com$ [NC] RewriteRule ^(.*)$ http://www\.%{HTTP_HOST}/$1 [R=302,L,NE] This rule seems to work, as when you are off the network and go to example.com in the browser, you get redirected to www.example.com. The problem is when I'm on the network, and I go to example.com I get an error page, saying page can't be found. No server errors; just a page can't be found, as if the local DNS is causing it to stop looking at that point. I'm also using Nettica for DNS service and have this A record in place: example.com Host (A) Default xxx.xx.xxx.xx This handles the external DNS, but my problem seems to be related to my internal DNS. For example, inside my network, I can go to servers on the network with addresses like this: server.example.com server1.example.com server2.example.com These are configured in my local DNS. I'm just not sure how to get past the "empty" subdomain and go to example.com. Adding to this since it might not be clear. If I'm out side the example.com network, on another network, like example123.com, then when I go to example.com I'm redirected to www.example.com as expected, eg, the Apache rewrite rule is working. Thanks in advance for any information.

  Read the article

• GRE Tunnel over IPsec with Loopback

  - by Alek

  Hello, I'm having a really hard time trying to estabilish a VPN connection using a GRE over IPsec tunnel. The problem is that it involves some sort of "loopback" connection which I don't understand -- let alone be able to configure --, and the only help I could find is related to configuring Cisco routers. My network is composed of a router and a single host running Debian Linux. My task is to create a GRE tunnel over an IPsec infrastructure, which is particularly intended to route multicast traffic between my network, which I am allowed to configure, and a remote network, for which I only bear a form containing some setup information (IP addresses and phase information for IPsec). For now it suffices to estabilish a communication between this single host and the remote network, but in the future it will be desirable for the traffic to be routed to other machines on my network. As I said this GRE tunnel involves a "loopback" connection which I have no idea of how to configure. From my previous understanding, a loopback connection is simply a local pseudo-device used mostly for testing purposes, but in this context it might be something more specific that I do not have the knowledge of. I have managed to properly estabilish the IPsec communication using racoon and ipsec-tools, and I believe I'm familiar with the creation of tunnels and addition of addresses to interfaces using ip, so the focus is on the GRE step. The worst part is that the remote peers do not respond to ping requests and the debugging of the general setup is very difficult due to the encrypted nature of the traffic. There are two pairs of IP addresses involved: one pair for the GRE tunnel peer-to-peer connection and one pair for the "loopback" part. There is also an IP range involved, which is supposed to be the final IP addresses for the hosts inside the VPN. My question is: how (or if) can this setup be done? Do I need some special software or another daemon, or does the Linux kernel handle every aspect of the GRE/IPsec tunneling? Please inform me if any extra information could be useful. Any help is greatly appreciated.

  Read the article

• Combining URL mapping and Access-Control-Allow-Origin: *

  - by ksangers

  I am in the progress of migrating an old banner system to a new one and in doing so I want to rewrite the old banner system's URL's to the new one. I load my banners via an AJAX request, and therefore I require the Access-Control-Allow-Origin to be set to *. I have the following VirtualHost configuration: <VirtualHost *:80> ServerAdmin [email protected] ServerName banner.studenten.net # we want to allow XMLHTTPRequests Header set Access-Control-Allow-Origin "*" RewriteEngine on RewriteMap bannersOldToNew txt:/home/user/banner.studenten.net/banner-studenten-net-to-ads-all4students-nl-map # check whether a zoneid exists in the query string RewriteCond %{QUERY_STRING} ^(.*)zoneid=([1-9][0-9]*)(.*) # make sure the requested banner has been mapped RewriteCond ${bannersOldToNew:%2|NOTFOUND} !=NOTFOUND # rewrite to ads.all4students.nl RewriteRule ^/ads/.* http://ads.all4students.nl/delivery/ajs.php?%1zoneid=${bannersOldToNew:%2}%3 [R] # else 404 or something ErrorLog ${APACHE_LOG_DIR}/banner.studenten.net-error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog ${APACHE_LOG_DIR}/banner.studenten.net-access.log combined </VirtualHost> My map file, /home/user/banner.studenten.net/banner-studenten-net-to-ads-all4students-nl-map, contains something like: # oldId newId 140 11 141 12 142 13 Based on the above configuration I was expecting the following: GET /ads/ajs.php?zoneid=140 HTTP/1.1 Host: banner.studenten.net HTTP/1.1 302 Found ... Access-Control-Allow-Origin: * Location: http://ads.all4students.nl/delivery/ajs.php?zoneid=11 But instead I get the following: GET /ads/ajs.php?zoneid=140 HTTP/1.1 Host: banner.studenten.net HTTP/1.1 302 Found ... Location: http://ads.all4students.nl/delivery/ajs.php?zoneid=11 Note the missing Access-Control-Allow-Origin header, this means the XMLHttpRequest is denied and the banner is not displayed. Any suggestions on how to fix this in Apache?

  Read the article

• Exchange 2010 Hub cannot deliver to Exchange 2007 Hub - "451 5.7.3 Cannot achieve Exchange Server authentication"

  - by Graeme Donaldson

  We have an existing Exchange 2007 server in Site A (exch07). I've installed an Exchange 2010 server in Site B (exch10). Both servers have the CAS, Mailbox and Hub roles. Messages sent via SMTP on exch10 which are destined for mailboxes on exch07 are queued with the "Last Error" reported in Queue Viewer as '451 4.4.0 Primary target IP address responded with: "451 5.7.3 Cannot achieve Exchange Server authentication." Attempted failover to alternate host, but that did not succeed. Either there are no alternate hosts, or delivery failed to all alternate hosts.' I've found that some people have resolved this by creating new Receive Connectors which are scoped specifically to apply to connections from the remote hub/s, but I have had no luck doing this. Specifically I created new receive connectors on both servers with the following settings: Remote IP = IP/s of remote server Authentication = "Transport Layer Security (TLS)" and "Exchange Server authentication" Permission Groups = "Exchange servers" and "Legacy Exchange Servers" This made no difference, I see the same error message. What am I missing? Update: We noticed that the Application log had this error message from MSExchangeTransportService: Microsoft Exchange could not find a certificate that contains the domain name exch07.domain.local in the personal store on the local computer. Therefore, it is unable to support the STARTTLS SMTP verb for the connector exch10 with a FQDN parameter of exch07.domain.local. If the connector's FQDN is not specified, the computer's FQDN is used. Verify the connector configuration and the installed certificates to make sure that there is a certificate with a domain name for that FQDN. If this certificate exists, run Enable-ExchangeCertificate -Services SMTP to make sure that the Microsoft Exchange Transport service has access to the certificate key. It turns out that the default self-signed certificate was no longer enabled for the SMTP service for some reason. After enabling the self-signed certificate for SMTP, we no longer get the error in the event logs, but delivery is still failing with the same error message. Update 2: I put a mailbox on exch10 and attempted to deliver a message via SMTP on exch07 and I get the same error.

  Read the article

• PDU management interface has low availability - product flaw or isolated issue

  - by DeanB

  Our colocation provider has supplied us with APC AP7932 switched 0U PDUs as part of several cabinets they provide us. We have had a lot of trouble with the network management aspect of these PDUs, which I'll describe below. We are moving to cage space in the same datacenter, and plan to provide our own PDUs, so I'd like to determine which enterprise-grade PDUs have been reliable performers from a remote management perspective. Our colo-provided PDUs are configured to support management via an SSL web UI and via telnet. We updated the firmware on all of them to the current version as of NOV2011. They respond to pings reliably, and we have no reason to suspect a network layer issue. However, we experience frequent hangs, timeouts, disconnects, and general unavailability from the embedded management host in all of the PDUs. We occasionally have to restart the microcontroller on the PDU to recover from what appears to be an occasional hard fault. The outlets stay powered (thankfully), but the management aspect is so unreliable that it has become an ops liability - we can't be confident that we could get into the PDU to power cycle a host if we needed to. We have 3 PDUs that all exhibit identical behavior. There are many manufacturers of enterprise-grade 0U switched PDUs, all with comparable features. If I looked at the datasheet for our current PDUs, they would appear to be a good fit -- only with the benefit of suffering through using them do we know to avoid them. I'd like to avoid picking a PDU that looks fine on paper, but has similar reliability issues. What has been others' experience with switched PDUs? Is this level of flakiness normal?

  Read the article

• ntop to analyse bandwidth usage on multiple ASA 5505

  - by dunxd

  I have set up a netflow server at our data centre, which is connected via VPN to ~40 remote offices using Cisco ASA 5505. The aim is to analyse usage data and find out exactly how the remote connections are being used. I followed through http://techowto.files.wordpress.com/2008/09/ntop-guide.pdf to set up ntop and https://supportforums.cisco.com/docs/DOC-6114 to set up the ASAs. I can see from the Plugin Netflow Statistics page that netflow packets from my ASAs are being received - the counter is increasing. However, I am not seeing any breakdown on the Global Traffic Statistic page after switching to the Netflow interface. I'm just seeing a pie chart showing 100% traffic for eth0. The interfaces and documentation are a little hard to follow so I am not sure I have got things configured correctly. When setting up my NetFlow-device.2 I can specify Virtual NetFlow Interface Network Address - the web UI says This value is in the form of a network address and mask on the network where the actual NetFlow probe is located. is this a Network address (e.g. 192.168.0.0/24) or an actual host IP address (192.167.0.1/24)? If that should be a network address, is this the network in which one of my ASAs is or the network in which my ntop server is? If a host IP address, is this the IP address used by eth0 on my ntop server, the IP address of an ASA, or something else? Do I need a separate virtual interface for each ASA I am collecting netflow data from? Any guidance would be greatly welcome.

  Read the article

• SSHing thru an HTTP proxy

  - by Siler

  Typical scenario: I'm trying to SSH thru a corporate HTTP proxy to a remote machine using corkscrew, and I get: ssh_exchange_identification: Connection closed by remote host Obviously, there's a lot of reasons this might be happening - the proxy might not allow this, the remote box might not be running sshd, etc. So, I tried to tunnel manually via telnet: $ telnet proxy.evilcorporation.com 82 Trying XX.XX.XX.XX... Connected to proxy.evilcorporation.com. Escape character is '^]'. CONNECT myremotehost.com:22 HTTP/1.1 HTTP/1.1 200 Connection established So, unless I'm mistaken... it looks like the connection is working. So, why then, doesn't it work via corkscrew? ssh -vvv [email protected] -p 22 -o "ProxyCommand corkscrew proxy.evilcorporation.com 82 myremotehost.com 22" OpenSSH_6.6, OpenSSL 1.0.1f 6 Jan 2014 debug1: Reading configuration data /etc/ssh/ssh_config debug1: /etc/ssh/ssh_config line 19: Applying options for * debug1: Executing proxy command: exec corkscrew proxy.evilcorporation.com 82 myremotehost.com 22 debug1: permanently_set_uid: 0/0 debug1: permanently_drop_suid: 0 debug1: identity file /root/.ssh/id_rsa type -1 debug1: identity file /root/.ssh/id_rsa-cert type -1 debug1: identity file /root/.ssh/id_dsa type -1 debug1: identity file /root/.ssh/id_dsa-cert type -1 debug1: identity file /root/.ssh/id_ecdsa type -1 debug1: identity file /root/.ssh/id_ecdsa-cert type -1 debug1: identity file /root/.ssh/id_ed25519 type -1 debug1: identity file /root/.ssh/id_ed25519-cert type -1 debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_6.6p1 Ubuntu-2ubuntu1 ssh_exchange_identification: Connection closed by remote host

  Read the article

• Mysql master-master not replicating

  - by frankil

  I'm setting up a master-master mysql replication on two servers (db1 and db2). I started with setting up db2 as a slave to db1 and that works fine. But when I set up db1 as a slave to db2 it isn't replicating. On the face of it everything looks fine but the data isn't replicating. There are no errors in either of the error logs. The slave status is updating the bin log position. I have used mysqlbinlog to examine both the binlog on the db2 and the relay log on db1 and all of the queries are going in there, but not being executed to db1. "show slave status" on both servers shows that both the slave io and sql threads are "Yes" and that the relay log position is updated by the sql thread. Also on both servers: >echo "show processlist" | mysql | grep "system user" 166819 system user NULL Connect 3655 Waiting for master to send event NULL 166820 system user NULL Connect 3507 Has read all relay log; waiting for the slave I/O thread to update it NULL Relevant config for db1: server-id = 1 log-slave-updates replicate-same-server-id = 0 auto_increment_increment = 4 auto_increment_offset = 1 master-host = db2 master-port = 3306 master-user = slaveuser master-password = *** skip-slave-start sync_binlog = 1 binlog-ignore-db=mysql Config for db2 server-id = 2 log-slave-updates replicate-same-server-id = 0 auto_increment_increment = 4 auto_increment_offset = 2 master-host = db1 master-port = 3306 master-user = slaveuser master-password = *** sync_binlog = 1 relay-log=mysql-relay-bin binlog-ignore-db=mysql What else can I look for to make sure db1 executes the queries from db2?

  Read the article

• Using %v in Apache LogFormat definition matches ServerName instead of specific vhost requested

  - by Graeme Donaldson

  We have an application which uses a DNS wildcard, i.e. *.app.example.com. We're using Apache 2.2 on Ubuntu Hardy. The relevant parts of the Apache config are as follows. In /etc/apache2/httpd.conf: LogFormat "%v %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog In /etc/apache2/sites-enabled/app.example.com: ServerName app.example.com ServerAlias *.app.example.com ... CustomLog "|/usr/sbin/vlogger -s access.log /var/log/apache2/vlogger" vlog Clients access this application using their own URL, e.g. company1.app.example.com, company2.app.example.com, etc. Previously, the %v in the LogFormat directive would match the hostname of the client request, and we'd get several subdirectories under /var/log/apache2/vlogger corresponding to the various client URLs in use. Now, %v appears to be matching the ServerName value, so we only get one log under /var/log/apache2/vlogger/app.example.com. This breaks our logfile analysis because the log file has no indication of which client the log relates to. I can fix this easily by changing the LogFormat to this: LogFormat "%{Host}i %h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" vlog This will use the HTTP Host: header to tell vlogger which subdirectory to create the logs in and everything will be fine. The only concern I have is that this has worked in the past and I can't find any indication that this has changed recently. Is anyone else using a similar config, i.e. wildcard + vlogger and using %v? Is it working fine?

  Read the article

• Rsync: Only preserve meta (time, group, etc) on files and sub-directories, not root directory

  - by Svish

  I am copying some files (all except hidden ones) using rsync from one place to another using this command: rsync -Cav --delete --exclude=.* /Some/Directory/ other-host:/Other/Directory It works nice except that I get the following errors: rsync: chgrp "/Other/Directory/." failed: Operation not permitted (1) rsync: failed to set times on "/Other/Directory/.": Permission denied (13) That is understandable because I do in fact not have those permissions, and I also do not want to change the group of that directory. I only want to do this for all the files and directories that are in that directory. Is there any way to solve this? Tried to --exclude=. and --exclude=./, but those didn't work. Any ideas? I have no idea how to fix this... More details: This is on Mac OS X, and the directories I am syncing is from a local mounted volume to the /Users/Shared/ directory on the other host. That directory has user root and group wheel. The files inside it has user admin and group staff and so does the local source directory.

  Read the article

• Can I use CNAME with ip address? Why If works (sometimes)?

  - by Maciek Sawicki

  I believe that the easiest answer for the first question is "No, You have "A" for this", but I accidentally setup some subdomain using CNAME pointing to ip address and it worked on few computers in my office. I wonder how it was possible? Now, when I'm checking it from home I have following error: beast:~ viroos$ host somesubdomain.somedomain.com Host somesubdomain.somedomain.com not found: 3(NXDOMAIN) I'm 100% it used to work at my office (currently it looks like it doesn't, but I'm checking it on different machine). Therefore I'm not 100% if it worked due to some special network setup or because I tested it just after adding DNS entry. I know this story sounds, a little crazy/incredibly, but can someone help me solve this puzzle. //edit: I'm adding dig output ; <<>> DiG 9.6-ESV-R4-P3 <<>> somesubdomain.somedomain.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NXDOMAIN, id: 60224 ;; flags: qr rd ra; QUERY: 1, ANSWER: 1, AUTHORITY: 1, ADDITIONAL: 0 ;; QUESTION SECTION: ;somesubdomain.somedomain.com. IN A ;; ANSWER SECTION: somesubdomain.somedomain.com. 67 IN CNAME xxx.xxx.xxx.xx1. ;; AUTHORITY SECTION: . 1800 IN SOA a.root-servers.net. nstld.verisign-grs.com. 2012040901 1800 900 604800 86400 ;; Query time: 72 msec ;; SERVER: 8.8.8.8#53(8.8.8.8) ;; WHEN: Tue Apr 10 00:11:01 2012 ;; MSG SIZE rcvd: 136

  Read the article

• guest crash on long backup via rsync

  - by ToreTrygg

  I recently upgraded host to Ubuntu 9.10 with vmware server 2.0.2, i had two guest machine. One is a sme server i had several crash during a session of backup with rsync to another pc. Normal activities run regularly. The other guest is up without problem since 25 days. I found in the log a lot o f row like these Dec 20 05:29:27.445: vcpu-1| VLANCE: Ethernet0 skipped 2560 time(s) Dec 20 05:29:27.445: vcpu-1| VLANCE: 66 12 5 8 2 3 3 0 1 0 0 1 0 1 2 0 Dec 20 05:29:27.445: vcpu-1| VLANCE: 0 0 1 0 1 0 0 0 1 0 0 0 0 1 0 2452 Dec 20 05:29:27.651: vmx| ide0:0: Command WRITE(10) took 1.947 seconds (ok) Dec 20 05:29:37.945: vmx| ide0:0: Command WRITE(10) took 1.033 seconds (ok) when the vitual machine crash the log report, I paste here only some part to limit the lenght of the message Dec 27 01:48:05.686: Worker#2| Caught signal 6 -- tid 700 Dec 27 01:48:05.686: Worker#2| SIGNAL: eip 0x460422 esp 0xb124c024 ebp 0xb124c03 Dec 27 01:48:05.712: Worker#2| SymBacktrace12 00000000 eip 0x39d7ee in function clone in object /lib/tls/i686/cmov/libc.so.6 loaded at 0x2d1000 Dec 27 01:48:05.719: Worker#2| Unexpected signal: 6. Dec 27 01:48:05.720: Worker#2| Core dump limit is 0 KB. Dec 27 01:48:05.762: Worker#2| Child process 10455 failed to dump core (status 0 x6). Dec 27 01:48:05.762: Worker#2|SymBacktrace13 00000000 eip 0x39d7ee in function clone in object /lib/tls/i686/cmov/libc.so.6 loaded at 0x2d1000 Dec 27 01:48:05.779: Worker#2|Msg_Post: Error Dec 27 01:48:05.780: Worker#2|http://msg.log.error.unrecoverable VMware Server unrecoverable error: (Worker#2) Dec 27 01:48:05.780: Worker#2|Unexpected signal: 6. I have no idea how to solve the problem with this installation, I think to dowgrade the host to a version more compatible with vmware server 2. I read a lot of post about difficult of installation I think the problem of compilation during install could be related to my problem. Excuse me if the post isn't very clear, it's my first post here. Any help or suggest will be appreciated. Thanks

  Read the article

• Cannot Connect To VMWare Guest OS Using Either RDP or VNC

  - by Humanier

  Hi, I have a PC (Windows XP SP3) with VMWare Workstation 7 installed. The VMWare hosts Windows Server 2003 Enterprise Edition R2. RealVNC (4.1.3) is installed on both OS'es. Both of them use Hamachi2. Host OS (WinXP) also runs ZoneAlarm Firewall. Hamachi network is set as trusted. My goal is to allow RDP and VNC connections to be made to the guest OS (Windows Server 2003). Both options work absolutely fine if I connect from the host OS. However I have problems when other computers from our Hamachi network try to connect the guest OS (Win2K3). 1) RDP connections. RDP window opens, shows black content and after 15-20 seconds displays following error: http://lh6.ggpht.com/_yQhsRRimgKU/TArRrtiteQI/AAAAAAAABZA/e96za-y9wzo/rdp_error.JPG 2) RealVCN connections. Users are able to connect but all they see is a black screen inside VNC window. At the same their input (keystrokes or mouse moves/clicks) are visible when looking at the console window of the Win2K3. I really appreciate any ideas on how to resolve mentioned problems. Thank you in advance.

  Read the article

< Previous Page | 377 378 379 380 381 382 383 384 385 386 387 388  | Next Page >