Search Results

Search found 35708 results on 1429 pages for 'default copy constructor'.

Page 382/1429 | < Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >

• Is 50% download speed on a wireless G network normal?

  - by Bartlomiej Skwira

  I have a wired connection of about 36Mb/s, but my wireless speed is max at about 18-19Mb/s. I have a WRT54G-TM (T-Mobile, 802.11G) router with DD-WRT firmware - I've upgraded it to latest build. Done some settings changes: changed channel - 13 wireless network mode - G-only ACK Timing - 0 Fragmentation Threshold and RTS Threshold - 2304 Basic Rate - All Signal/Noise ratio: -46/-94, signal quality ~50-60%. Is this normal with G networks? Edit: The AP is located about 2 meters from laptop, no walls or metal objects, but its next to a TV. I've done a channel scan (had problems locating it, go to "Status - Wireless - Site survey" - lame naming) and everybody else is on channels 1 and 6. Switched to channel 11 but it didn't help. As for trasmit power I got best results with default 71mw. The antenna might be a factor, I'm using the default 2 antennas.

  Read the article

• How to stop Office 2010 changing " and ' to smart quotes

  - by fatherjack

  I have recently upgraded to Office 2010 at work and there are a few things that are a real problem for me. As a T-SQL developer and SQL Server DBA I copy and paste code to and from various applications and if Word gets involved it can has disastrous consequences. There is an option that appears to be defaulted to "on" that changes a straight quote to what Word describes as a smart quote - see the image below. Note - the single quote suffers from the same effect. Now, getting to the point that...(read more)

  Read the article

• ATI 9550 shows up as laptop in displays after update to 12.04, how do I fix this?

  - by D_H

  My guess is this is on here somewhere but I have searched and even tried looking at bunch of other similar video problems. My ATI 9550 shows up as laptop in displays after update to Ubuntu 12.04, how do I fix this? I found the following command on another post sudo lshw -c video. I get this when I run that command: *-display:0 UNCLAIMED description: VGA compatible controller product: RV350 AS [Radeon 9550] vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 32 bits clock: 66MHz capabilities: agp agp-3.0 pm vga_controller bus_master cap_list configuration: latency=32 mingnt=8 resources: memory:c0000000-cfffffff ioport:c000(size=256) memory:e5000000-e500ffff memory:e4000000-e401ffff *-display:1 UNCLAIMED description: Display controller product: RV350 AS [Radeon 9550] (Secondary) vendor: Hynix Semiconductor (Hyundai Electronics) physical id: 0.1 bus info: pci@0000:01:00.1 version: 00 width: 32 bits clock: 66MHz capabilities: pm cap_list configuration: latency=32 mingnt=8 resources: memory:d0000000-dfffffff memory:e5010000-e501ffff" This way more info than the command showed in he other post and as far as I can tell right. This doesn't look to me like a laptop video would list? I also see this command xrandr, it reports this: xrandr: Failed to get size of gamma for output default Screen 0: minimum 640 x 480, current 1280 x 1024, maximum 1280 x 1024 default connected 1280x1024+0+0 0mm x 0mm 1280x1024 0.0* 1024x768 0.0 800x600 0.0 640x480 0.0 This is what shows in displays for resolutions but only the 1280x1024 works the others produce tearing in the video. Also I should have mentioned 3D mode does not work. I have tried ATI/AMD drivers the new one won't load and older ones won't work. I found out the newer driver no longer supports the 9550.

  Read the article

• Help understanding the migrate wubi documentation?

  - by user110259

  I'm looking at the MigrateWubi page but I'm not sure if I need to change the partition directories to the ones I created, and if so, I'm not too sure which ones I need to change. Here are the partitions I've made: Should I just copy and paste: sudo bash wubi-move.sh /dev/sda5 /dev/sda6 into my terminal or something else? Also, do I enter just this one line or do i need to enter any other commands in there? Thanks!

  Read the article

• Bringing the xenbr0 interface up on XEN under Ubuntu 8.04

  - by iyl

  I installed XEN on Ubuntu 8.04 using this tutorial: http://www.howtoforge.com/ubuntu-8.04-server-install-xen-from-ubuntu-repositories but after I reboot with the XEN kernel, I don't have xenbr0 device. I see that network-bridge script runs and it creates peth0 device, but not xenbr0. I have a very basic IP setup, with a single static IP defined in /etc/network/interfaces. The only unusual thing is that my hosting (1&1) gave me a netmask 255.255.255.255, so I had to add the default gateway with this script: /sbin/route add -host 10.255.255.1 dev eth0 /sbin/route add default gw 10.255.255.1 Everything else is plain vanilla Ubuntu 8.04.

  Read the article

• Distribution upgrade freezes

  - by lugte098

  When upgrading from Ubuntu 10.04 to 10.10 the distribution upgrade program freezes after it notifies me of a change in /etc/apparmor.d/usr.bin.mysqld and asks me to keep the old file or accept the new changes (I accepted them). The terminal says: Configuration file `/etc/apparmor.d/usr.sbin.mysqld' ==> Modified (by you or by a script) since installation. ==> Package distributor has shipped an updated version. What would you like to do about it ? Your options are: Y or I : install the package maintainer's version N or O : keep your currently-installed version D : show the differences between the versions Z : start a shell to examine the situation The default action is to keep your current version. *** usr.sbin.mysqld (Y/I/N/O/D/Z) [default=N] ? y Installing new version of config file /etc/apparmor.d/usr.sbin.mysqld ... The program hasn't done anything after this for about 2 hours now and I have no idea what I should do at this point. Can I quit the program and restart it? Or is there another action I should take? It did however change the '/etc/apparmor.d/usr.sbin.mysqld' to the new version, but is still frozen...

  Read the article

• What do ptLineDist and relativeCCW do?

  - by Fasih Khatib

  I saw these methods in the Line2D Java Docs but did not understand what they do? Javadoc for ptLineDist says: Returns the distance from a point to this line. The distance measured is the distance between the specified point and the closest point on the infinitely-extended line defined by this Line2D. If the specified point intersects the line, this method returns 0.0 Doc for relativeCCW says: Returns an indicator of where the specified point (PX, PY) lies with respect to the line segment from (X1, Y1) to (X2, Y2). The return value can be either 1, -1, or 0 and indicates in which direction the specified line must pivot around its first endpoint, (X1, Y1), in order to point at the specified point (PX, PY). A return value of 1 indicates that the line segment must turn in the direction that takes the positive X axis towards the negative Y axis. In the default coordinate system used by Java 2D, this direction is counterclockwise. A return value of -1 indicates that the line segment must turn in the direction that takes the positive X axis towards the positive Y axis. In the default coordinate system, this direction is clockwise. A return value of 0 indicates that the point lies exactly on the line segment. Note that an indicator value of 0 is rare and not useful for determining colinearity because of floating point rounding issues. If the point is colinear with the line segment, but not between the endpoints, then the value will be -1 if the point lies "beyond (X1, Y1)" or 1 if the point lies "beyond (X2, Y2)".

  Read the article

• How to setup an Openvpn server with two gateways to internet

  - by fourat

  I have an openvpn server behind two wan interfaces: eth1 and eth2 where eth1 is the default gw and eth2 is where openvpn binds to. The problems my ovpn server is replying back to ovpn client via the default gw (through eth1) and the tcp negociation is lost before establishing any tunnel. Here's what's happening: wan client -----> eth2 ----> openvpn -----> eth1 ----> lost and not delivered back to client Is there a way to tell ovpn to stick on eth2 and consider it for all traffic ?

  Read the article

• Locale setting on a Red Hat box

  - by sasuke

  Hi all, Recently our organization got a couple of server boxes which are I guess present in some data-center in UK. The problem is that for some reason the default Locale representation in Java on that server returns en_US instead of the expected en_GB (I confirmed this by running a code on that server which simply outputs Locale.default()). I am pretty sure this has got something to do the way in which the boxes were set up. My question is: what would be the approach to fix this issue now that the OS has been installed? Is there any way I can for a given SSH session set the locale as en_GB instead of the current en_US? TIA, sasuke

  Read the article

• Keeping local folders synchronized

  - by Earthling

  After repeatedly losing data on encrypted drives due to some trivial combination of software and hardware failure, I would like to know if there is a simple tool that keeps local folders synchronized. Like a local "cloud" service that runs on one computer and synchronizes any changes in one folder to the other folder as soon as both folders are available. That way I can keep a copy of the most important files on a different hard-drive.

  Read the article

• Turn off write barriers on ext4 whiche FS is mounted

  - by user462982

  I am doing some IO intensive DB imports that run for several days now and the IO performance has dropped tremendously over times. The DB data files (log files) are on an ext4 formatted logical volume which is mounted with default options (did not specify something special in fstab). Since I just learned that ext4 enables write barriers by default: Q: Is there some way to disable write barriers online (i.e. while the file system is in use), because I cannot interrupt the import and don't want to restart it again. I am aware that write barriers might not be the only thing impeding performance it is a bad idea to have write barriers disabled on journalling file systems if data safty is important (e.g. on a production system)

  Read the article

• How to connect another computer to the router

  - by Call Me Dummy

  I already have a Windows 7 PC connected to my NETGEAR WGR614v10 router and I am able to use internet in that computer. Now I need to connect one of my old computer to the router to share the internet. It's also running Windows 7. I already connected it to the router via a CAT-5 cable but I am not able to use internet. The first computer was set up by a technician. Its IP address is 192.168.1.3, and the default gateway is 192.168.1.1. On the second PC, I changed the IPv4 to 192.168.1.4 and default gateway and preferred DNS to 192.168.1.1, but it's not working. What can I do?

  Read the article

• Nvidia drivers with GeForce 680M problem [closed]

  - by biofermin

  Possible Duplicate: There's an issue with an Alpha/Beta Release of Ubuntu, what should I do? I have a new Alienware M17x which I have installed 64-bit Ubuntu 12.10 (dual boot). I have tried various ways to install the Nvidia drivers for the GeForce GTX 680M (which they claim they are compatible with): from Ubuntu Software Centre (though Additional Drivers fails to detect the card.) using sudo apt-get install nvidia-current downloading the drivers from nvidia and manually installing them (ctrl + alt + F6, sudo service lightdm stop, sudo ./NVIDIA*, sudo reboot) (each with a clean install of Ubuntu) but in all cases, when I reboot after installing nvidia-setings claims that I am not using the driver and should sudo nvidia-xconfig from the terminal, which I do but this has no effect and I am stuck in crappy resolution until I rm /etc/X11/xorg.conf and reboot. The xorg.conf that nvidia-xconfig generates is: Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection Section "Files" EndSection Section "InputDevice" # generated from default Identifier "Mouse0" Driver "mouse" Option "Protocol" "auto" Option "Device" "/dev/psaux" Option "Emulate3Buttons" "no" Option "ZAxisMapping" "4 5" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" Identifier "Monitor0" VendorName "Unknown" ModelName "Unknown" HorizSync 28.0 - 33.0 VertRefresh 43.0 - 72.0 Option "DPMS" EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" EndSection Section "Screen" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 SubSection "Display" Depth 24 EndSubSection EndSection

  Read the article

• macports apache,php,db, how do I test on another device?

  - by brokenindexfinger

  My supervisor suggests using macports to install/manage different versions of apache and php, as well as both mysql and posgres databases. The idea is that we need to test our platform on different versions of each. So far I've just been using the default apache installation on osx lion, and the default postgres installation. My question is this: once I turn Web Sharing off, and proceed with a custom apache2 setup based in /opt/local/, how do I broadcast my machine's IP to other devices, for testing? With Web Sharing, I can get my machine's IP and use that to test with an iPad and iPhone. Will that still be the case, and if so, how do I do it?

  Read the article

• difference between success and failed event in auditd/aureport

  - by user112358132134

  The aureport command has two options that limit the list of displayed events to those that were successful and those that failed. Per the man page: --failed Only select failed events for processing in the reports. The default is both success and failed events. --success Only select successful events for processing in the reports. The default is both success and failed events. What does this mean? Is the failure/success with regard to the actual event (e.g., a syscall that returned non-zero) or does the failure/success apply to auditd and whether or not there was an issue in processing the event?

  Read the article

• What's the best way to install mod-wsgi for a specific version of python (2.7) on Debian (squeeze)?

  - by Pascal Polleunus

  System info: Debian Squeeze Python versions: 2.6.6 (default) & 2.7.2 mod-wsgi: 3.3-2 in /usr/lib/apache2/modules: mod_wsgi.so -> mod_wsgi.so-2.6 mod_wsgi.so-2.5 mod_wsgi.so-2.6 I've a virtualenv configured with Python 2.7 but my application runs 2.6.6, apparently because mod-wsgi is using the default version of the system. The way to go seems to configure mod-wsgi to use 2.7 (i.e. system-wide, not specific to a virtualenv). How can I install mod_wsgi.so-2.7? After installing that, I'll just have to change the symlink mod_wsgi.so to mod_wsgi.so-2.7.

  Read the article

• How to get headphones and speakers working at the same time?

  - by Borek

  I have a Gigabyte P55-UD3 motherboard which comes with a Realtek sound card and audio header for the front panel. My headset is permanently connected to the front panel (mic in, headphones in) and I also have speakers connected at the rear of the computer. What I want to achieve is that both the headphones and the speakers work at the same time. On my old PC with Realtek, I was able to do this by clicking "Device advanced settings" in the Realtek HD Audio Manager and then clicking "Make front and rear output devices playback two different audio streams simultaneously" and then doing some reassigning of front/rear settings in the Realtek Audio Manager (can't remember the details). But that doesn't seem to be working now - either the speakers play sounds or the headphones, not both at the same time. To pose the question differently, Windows plays the sounds on the "default device". I'd like to make both headphones and the speakers kind of like the default devices.

  Read the article

• How can I get magnet links for Ubuntu?

  - by badp

  Torrent files are being increasingly scrapped for magnet links, "mini torrent files" in concise and plain-text form that can be simply copy pasted around. Those link to the actual .torrent file "in the BitTorrent cloud", without relying on servers that may be temporarily overtaxed ("OMG NEW UNBUNT MUST GET NAO") or simply offline. Does Canonical offer magnet links for their Torrent distributions? Where can one find them?

  Read the article

• From the Coalface - 3 - Work as hard as you can to be as lazy as you can!

  - by TATWORTH

  The saga of the Change Log A recent conversation reminded me of the need for change logs within a database, to record when various change scripts were run. Creating such the required table is simple. A typical table for this consists of: Id - identity Integer primary key ChangeFileName - NVARCHAR(128) to hold the name of the file run. DateAdded - DateTime non-null with default value of getutcdate() Purpose - NVARCHAR(128) Rerunnable - Bit non-null default 0. By good design of the table only two data values normally need to be supplied. Two stored procedures, one for inserting data and one to list in reverse sequence the log complete the database essentials. The complete implementation can be found in the CommonData solution at http://CommonData.CodePlex.Com By including a call the add Change Log stored procedure, each script can log its name and purpose for posterity. The scripts that were applied to say the UAT system and their sequence of application can be readily identified for running on the Live system. Formatting XML XML is often produced as one continous string with no embedded CR/LF. To get it into human readable form, open it in visual studio, swap to another tab and back and click the format document button. The XML will then be nicely formatted!

  Read the article

• Running CopySourceAsHtml Add-in under Visual Studio 2010

  - by Marko Apfel

  Until now CopySourceAsHtml only supports Visual  Studio 2008 out of the box. But it is no problem to pimp up the config-file for supporting Visual Studio 2010. Copy all three files to "%userprofile%\Documents\Visual Studio 2010\Addins" Open CopySourceAsHtml.AddIn in a text editor and change both lines with <Version>9.0</Version> to <Version>10.0</Version> Run Visual Studio 2010 and CopySourceAsHtml works fine

  Read the article

• Per-user vhost logging

  - by kojiro

  I have a working per-user virtual host configuration with Apache, but I would like each user to have access to the logs for his virtual hosts. Obviously the ErrorLog and CustomLog directives don't accept the wildcard syntax that VirtualDocumentRoot does, but is there a way to achieve logs in each user's directory? <VirtualHost *:80> ServerName *.example.com ServerAdmin [email protected] VirtualDocumentRoot /home/%2/projects/%1 <Directory /home/*/projects/> Options FollowSymlinks Indexes IndexOptions FancyIndexing FoldersFirst AllowOverride All Order Allow,Deny Allow From All Satisfy Any </Directory> Alias /favicon.ico /var/www/default/favicon.ico Alias /robots.txt /var/www/default/robots.txt LogLevel warn # ErrorLog /home/%2/logs/%1.error.log # CustomLog /home/%2/logs/%1.access.log combined </VirtualHost>

  Read the article

• How to edit the Boot Graphics Resource Table / Edit windows 8 BOOT LOGO?

  - by user144773

  I want to edit the screen which is displayed when windows 8 (starts) loads (/loading). As for now it has the Toshiba logo, I want my custom logo or the windows default logo. I have found that UEFI has something called "Boot Graphics Resource Table" and that it overides the default logo if there is a image present (source) How can I edit the logo stored in UEFI firmware or Boot Graphics Resource Table? if it's in the "bootres.dll", which does UEFI use? My disk (spread across a few system/usefi/windows/etc partitions) has around twenty bootres.dlls. The bootres.dll is signed by Microsoft, but I don't have to worry because I can sign the file I edit myself with my own certificate.

  Read the article

• SEO Help - Advice For Small Biz Owners on How to Work Effectively With SEO Copywriters

  An SEO copy writer can be one of the best professional relationships you ever form. If you're a small business owner and you're thinking about hiring an SEO writer to produce content for your website or blog, following is how to get the most out of working with them.

  Read the article

• Get location of "true" GVFS path from Nautilus

  - by user946850

  I mount my Samba shares through Nautilus. I know that, behind the scenes, the share is fuse-mounted and Nautilus somehow does the translation between smb:// URLs and the actual location in the file system. Is it possible to retrieve the "true" path in the file system for a GVFS-mounted share, for a directory or a file? How? This is related, but does not answer my question: How to copy the current path from Nautilus?

  Read the article

• User cannot book a room resource

  - by bakesale

  Im having a problem with a specific user not being able to book a room resource. No error message is generated at all. The user attempts to add the room as a meeting resource and it simply doesnt register with the resources calendar. I have tested the resource with other accounts and other rooms for this user but it is only this room that is having issues for this user. This Exchange server was migrated from 2007 to 2010. All rooms except for the problem room were created back on Exchange 2007. This new room was created with Exchange 2010. Maybe this clue has something to do with the problem? This is a paste of the mailboxes folder permissions [PS] C:\Windows\system32Get-MailboxFolderPermission -identity cbr125:\calendar RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Default AccessRights : {Author} Identity : Default IsValid : True RunspaceId : 448ab44a-4c2a-4403-b46c-fce1106c0823 FolderName : Calendar User : Anonymous AccessRights : {None} Identity : Anonymous IsValid : True

  Read the article

< Previous Page | 378 379 380 381 382 383 384 385 386 387 388 389  | Next Page >