Search Results

Search found 16287 results on 652 pages for 'browser refresh'.

Page 384/652 | < Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• ipv6 reverse DNS delegation

  - by user1709492

  I currently have 2001:1973:2303::/48 assigned to me and i'll be assigning /64's to customer's I'd like to have 1 zonefile for the /48 where i can essentially point / redirect query to different nameservers. Example ( Desired effect ) 2001:1973:2303:1234::/64 -> ns1.example.com, ns2.example.com 2001:1973:2303:2345::/64 -> ns99.example2.com, ns100.example2.com 2001:1973:2303:4321::/64 -> ns1.cust1.com, ns2.cust1.com Current /48 zonefile $TTL 3h $ORIGIN 3.0.3.2.3.7.9.1.1.0.0.2.ip6.arpa. @ IN SOA ns3.example.ca. ns4.example.ca. ( 2011071030 ; serial 3h ; refresh after 3 hours 1h ; retry after 1 hour 1w ; expire after 1 week 1h ) ; negative caching TTL of 1 hour IN NS ns3.example.ca. IN NS ns4.example.ca. 1234 IN NS ns1.example.com. NS ns2.example.com. 2345 IN NS ns99.example2.com. NS ns100.example2.com. 4321 IN NS ns1.cust1.com. NS ns2.cust1.com. Where am i going wrong ? My request seems simple to me atleast. To put it in terms of firewalling i want to redirect traffic client queries 2001:1973:2303:4321::1 - ns3.example.ca sees the request and redirects the query to ns1.cust1.com - ns1.cust1.com answers the query with omg.itworks.ca ( provided ns1.cust1.com is properly configured.

  Read the article

• Laptop Overheating with Windows 8

  - by Dany Khalife

  I recently installed Windows 8 on my HP G62 Laptop and i have been noticing a very strange problem with it. Let alone, for lets say 5 minutes, without even touching it, it starts to heat up and it reaches about 60 degrees (Celsius) with absolutely no applications open (not just on desktop but overall). I dug in a little deep and found out that Maintenance was running when the computer was Idle, so i turned that off From the System's Task Scheduler, and while there i also turned off other services i did not need hoping that would solve the problem. So after a few days, i noticed that the average temperature of my laptop dropped from 55 to 48 degrees while working on Visual Studio. And when i thought the problem had disappeared, it still did show up, only not after 5 minutes, but more like 10 minutes... Here is what i have done so far: Replacing the thermal paste on the CPU and the fan and cleaning the fan (this was like 6 months ago) Using a laptop cooler Running a virus scan (i just formatted my laptop so it would be really weird if i already caught something but who knows) Right now, i believe it has something to do with my gfx driver (Even though it IS up to date, looking closely at the screen, i can see the pixels slowly refresh (kinda like watching static on TV) which i wasn't able to do on Windows 7. If you have any ideas, let me know. Thanks

  Read the article

• Oracle: Getting ORA-01195 and ORA-01110 when attempting resetlogs

  - by MacAnthony

  I am trying to get our database to startup. When I login to sqlplus and do a startup, I get the message: Total System Global Area 534462464 bytes Fixed Size 2215064 bytes Variable Size 331350888 bytes Database Buffers 192937984 bytes Redo Buffers 7958528 bytes Database mounted. ORA-01589: must use RESETLOGS or NORESETLOGS option for database open So I do a shutdown, startup mount (which works fine) and then run: SQL> alter database recover using backup controlfile until cancel; alter database recover using backup controlfile until cancel * ERROR at line 1: ORA-00283: recovery session canceled due to errors ORA-19909: datafile 1 belongs to an orphan incarnation ORA-01110: data file 1: '/<path>/system01.dbf' SQL> alter database open resetlogs; alter database open resetlogs * ERROR at line 1: ORA-01195: online backup of file 1 needs more recovery to be consistent ORA-01110: data file 1: '/<path>/system01.dbf' I know I've used instructions to get me past this error before, but I seem to be having trouble tracking it down. A bit of history: We wanted to refresh the data in this from another db so we attempted to do a expdb/impdb into this instance. The impdb did not complete correctly and got an end of file error message in it and hung (I still have the message in a log if it's important). Since the instance would start at this point, we decided to use the hotbackup process we have to restore the db. The hotbackups are from another server/instance. We went through the same process 2 weeks ago. At the point of recreating the control file is where we got to the issue above.

  Read the article

• IE6 does not follow 302 redirect - displays 404 instead

  - by Dexter

  One of our clients has reported that they are experiencing 404 (file not found) errors when attempting to navigate a website that we support. The behaviour only appears to affect her - other users on the same machine can navigate the website fine, but the problem follows her from one PC to another. I've had a good look through the IIS server logs and have identified the requests in question. The normal request pattern is as follows: POST /page.aspx - 80 - ... 401 1 0 POST /page.aspx - 80 DOMAIN/user ... 302 0 0 GET /anotherPage.aspx Request=833f80a5-f34c-4b0e-addb-d73e1ee1663a 80 - ... 401 1 0 GET /anotherPage.aspx Request=833f80a5-f34c-4b0e-addb-d73e1ee1663a 80 DOMAIN/user ... 200 0 However, requests for the affected user do not include a request for the redirected page, nor an entry for the 404, i.e.: POST /page.aspx - 80 - ... 401 1 0 POST /page.aspx - 80 DOMAIN/user ... 302 0 0 ... other unrelated requests Can anyone suggest what might trigger this behaviour, and how I might investigate the cause or prevent it from occuring? I read here that the Allow META refresh option in IE6 might trigger this behaviour, but I have not been able to replicate the behaviour by modifying this setting only.

  Read the article

• VGA to S-Video/Video converter showing mashed up picture.

  - by Matthijs Wessels

  Earlier I asked this question: *http://superuser.com/questions/132374/does-the-lenovo-t60p-vga-port-support-an-s-video-signal As a result I acquired the following item: http://cgi.ebay.nl/ws/eBayISAPI.dll?ViewItem&item=250588098582&ssPageName=ADME:B:EOIBSA:NL:1123 Yea I'm a cheapass... Anyway, it just arrived and now I am trying to get it to work... The manual is not very informative other than telling me, this is the vga in, this is the vga out, this is the s/video out etc. Plus it tells me the system should support the following resolutions@refresh rate: 640x480@60/72/75Hz 800x600@60/75Hz 1024x768@60Hz I can connect it to my laptop and then I connect the S/Video and the Video to my tv which only gives me a blurred image (like when you set your monitor to a resolution it doesn't support). The VGA out however works fine to my tft monitor. The are two switches on the converter. I think one switches between s/video and video and the other between PAL and NTSC. But alas, no combination seems to give a better picture (it does give a different picture). Can anyone help me to solve this problem? I have downloaded this program called powerstrip, but I have no idea how to use it and if it can even solve my problem... Thanks in advance. I use Windows XP on a Lenovo t60p and I try to connect it to a Philips 32PFL7403D/12 LCD TV from VGA to a converter to S-video or video.

  Read the article

• Web browsing through SSH tunnel gets stuck/clogged

  - by endolith

  I use tools like Tunnelier to log into my home Tomato router through SSH, and then use it as a proxy for web browsing, tunnel for Remote Desktop/VNC, etc. Most days it works great, but some days every page I try to view gets stuck, like the tunnel is clogged. I load a web page and it seems to be loading, then stops, with the little loading icon spinning and nothing happening. I refresh the page, I reboot the router, I reboot the other computers on my home network and turn off any bandwidth-hogging services on them, I've turned on QoS on the router to prioritize SSH. I don't understand what's getting stuck. Rebooting or disconnecting/reconnecting the SSH tunnel improves responsiveness for a minute, but then it gets clogged again. It also seems to help if I don't do anything on the tunnel for a few minutes, then it will be responsive for a bit and then get clogged again. Trying to open a terminal console from Tunnelier is also unresponsive, so it's not just a web browsing problem. Likewise, connecting to http://192.168.1.1 in the browser (to the router's web config through its own tunnel) is also slow/laggy/halting. The realtime bandwidth reported by the router is nowhere near my DSL connection's limits, though it does show big spikes during the laggy times, and the connection is responsive when it shows low bandwidths. How do I troubleshoot something like this?

  Read the article

• Firefox will not remember local site cookie

  - by Campo

  This is a weird one. We have a production server (Server 2008) and two staging servers (Server 2008 and Server 2003) I have sites on all of these. They all use cookies. On the Production server when browsing to our site www.supernovainteractive.com there is a cookie that detects when you visted the site and it will not refresh the logo animation (top left hand side) on clicking to another page. This works for all browsers on the production server. I’m not sure what’s going on but for some reason cookies are not working on one site in the 2008 staging server only. This is when browsing using Firefox (3.6.3) they work fine on all other browsers (IE, Chrome, Safari, Opera) In addition, the 2003 staging server works fine. You can test on the Supernova Interactive site by noticing the logo in the top left corner. It uses a cookie to detect if you’ve already seen the animation. Once you’ve seen it once, it doesn’t animate again until tomorrow. Currently, it’s animating every time. I have opened an outside facing port so others can see the issue. Http://exchange.supernova.com:10009 Any ideas on this one? Firewalls are off on the server. Notice you do not get a cookie from Exchange.supernova.com.

  Read the article

• Using wildcard domains to serve images without http blocking

  - by iopener

  I read that browsers sometimes block waiting for multiple images from the same host, and I'm trying to do everything I can to speed up page load times. One caveat: I need to serve files over HTTPS. Any opinions about whether this is feasible: Setup a wildcard cert for *.domain.com. Whenever I need an image, generate an number based on a hash mod 5 of the filename, and append it to an 'img' subdomain (eg img1.domain.com, img4.domain.com, img3.domain.com, etc.); the hash will make any filename always use the same subdomain, and therefore the browser should be able to cache the images Configure a dynamic virtualhost record to point all img#. subdomains to /var/www/img I am looking for feedback about this plan. My concerns are: Will I get warnings when my page has https:// links to multiple subdomains? Is the dynamic virtualhost record I'm talking about even possible? Considering the amount of processing this would require, is it likely to even produce any kind of overall benefit? I'm probably averaging a half-dozen images per page, with only half being changed on each page refresh. Thanks in advance for you feedback.

  Read the article

• Adding 2nd DC to the domain from a different subnet over VPN.

  - by EagerToLearn

  I'm in the process of adding a second DC to our domain and just want to make sure I have all the steps right before proceeding. Info: DC1 is 2008 R2 Standard. DC2 is 2008 R2 Standard. Network1 is 192.168.39.x/24 Network2 is 10.0.0.x/24 VPN is Sonicwall. The 2 DC's will be at two different sites, but the networks are connected by hardware VPN. (Sonicwall). The main DC server will be on the 192.168.39.0/24 network. The 2nd DC will be on 10.0.0.0/24. Here are the steps I plan to take; please let me know if I'm missing anything. Part 1: AD Sites and Services on DC1, create a new site and subnet for DC2. (Or should I create a new one for both?) (Can I use the default IPSiteLink and not change anything in there other than refresh timer?) Part 2: Point the DNS of DC2 to DC1. Run /forestprep and /domainprep (on both, or just DC1?). Dcpromo and select "Additional Domain Controller for Existing Domain". Then continue with normal steps with default locations for databases. EDIT: Didn't realize this was like reddit and required two skipped lines to skip one :P EDIT 2: When DCPromo-ing DC2, do I need to have "Append primary and connection specific DNS" and "Append parent suffixes of the primary DNS suffix" checked?

  Read the article

• My DNS works! But, what is the simplest way to add something to it?

  - by Alex

  This is my current DNS example.com.db zone file. I followed a tutorial. It works, because when I point to this DNS from another server via resolve.conf, it will actually forward me to the right IP when I do "ping example.com". ; ; BIND data file for example.com ; $TTL 604800 @ IN SOA example.com. info.example.com. ( 2007011501 ; Serial 7200 ; Refresh 120 ; Retry 2419200 ; Expire 604800) ; Default TTL ; @ IN NS ns1.example.com. @ IN NS ns2.example.com. example.com. IN MX 10 mail.example.com. example.com. IN A 192.168.254.1 www IN CNAME example.com. mail IN A 192.168.254.1 ftp IN CNAME example.com. example.com. IN TXT "v=spf1 ip4:192.168.254.1 a mx ~all" mail IN TXT "v=spf1 a -all" Right now, ping example.com....goes to 192.168.254.1. That's great!!! it works! My question is--how can I add something do this file so that when my other servers: ping dbserver1....goes to 44.245.66.222 ping cacheserver1 ....goes to 38.221.44.555 I want to use it like a universal hosts file for my machines.

  Read the article

• Win7 'locking' process/files/folders?

  - by Dynde

  I've had a fair bit problems with sometimes files/folders/processes being 'locked' by Windows. The weird thing is, it's not like the traditional sense, I think, where tools like UnlockIT and wholockme would work. It seems that just giving it a little often helps - making me think it could either be the HDD, the memory, or something in Windows. A scenario: I go into a folder - don't open anything at all, go back up, cut or drag-move the folder to someplace else, it says "Action can't be completed because the folder or a file in it is open in another program". Waiting sometimes 20 seconds sometimes a little longer, and I can move it. Another scenario is deleting a bunch of files in a folder, and it appears that everything is gone, but then suddenly after a few seconds an .exe file pops back up, and I can't delete it. Waiting a few minutes, then pressing refresh and it's gone. I have the strangest feeling that there's a problem with either HDD or memory. I already tried disabling Windows indexing service with no luck. Does anyone have any ideas? EDIT: I should say, that I have a very fast system, 16 GB DDR3 RAM, i7-2600k CPU, SSD main HDD, so I really should not be experiencing any sort of problems, where one might say that it's "reasonable" for the system not to respond right away. Edit2: And I updated SSD firmware a couple months ago, so it shouldn't be bad release FW either

  Read the article

• Unable to load Windows after using EasyBCD to Reset bcd [duplicate]

  - by johnny

  This question already has an answer here: How can I repair the Windows 8 EFI Bootloader? 9 answers My windows installation was working perfectly fine until i clicked "Reset BCD" in EasyBCD in Windows 8. After clicking that EasyBCD told me to add Win 8 entry via Add Entry Menu so i did. After restart, win 8 would not start. Neither would recovery F11. Attempts i made to Restore : Ran boot-repair from ubuntu live cd several time. Used Win8 system recovery disc created via virtualbox with win 8 preview iso. Automated repair from Win8 system recovery disc Ran following commands from cmd started from Win8 system recovery disc bootrec /fixmbr Result : Success message bootrec /rebuildbcd Result : after hitting (Y) "The requested system device cannot be found" System refresh started from Win8 system recovery disc gives error that device is locked. System reset started from Win8 system recovery disc gives error that required partition or device is missing or not accessible. Used automated repair from EasyRE disc. It gave success message. Used Fix boot problem from Macrium reflect winPE repair disc. Copied Recovery partition to usb. Booting from usb gave this error Your PC needs to be repaired. Error Code : 0XC000000f Press Enter to try again Press F8 for Startup Settings F8 & Enter does nothing I cannot install WIn7 or Win 8, error it gives : "windows cannot be installed on this disk. The selected disk is of the GPT partition style."

  Read the article

• Is there any proper documentation for mod-evasive?

  - by Question Overflow

  mod_evasive20 is one of the loaded modules on my httpd server. I read good things about how it can stop a DOS attack and wanted to try it out on my localhost. A search for mod_evasive turns up a blog post by the author which briefly describes what it does. Other than that, I can't seem to find a reference or a documentation on the apache modules site. I was wondering whether it is a module recognised by Apache since there is no mention of it on its website. I have a mod_evasive.conf file sitting in the /etc/http/conf.d folder that contains the following lines: LoadModule evasive20_module modules/mod_evasive20.so <IfModule mod_evasive20.c> DOSHashTableSize 3097 DOSPageCount 2 DOSSiteCount 50 DOSPageInterval 1 DOSSiteInterval 1 DOSBlockingPeriod 10 </IfModule> My understanding from the setting is that if I were to click refresh or send a form more than two times in a one second interval, apache will issue a 403 error and bar me from the site for 10 seconds. But that is not happening on my localhost. And I would like to know the reason. Thanks.

  Read the article

• win 7 something is causing excessive disk usage, maybe chrome?

  - by camcam

  On my Win 7 computer, this happens: I work for several hours without problems, also using Chrome Suddenly, just after refreshing a page in Chrome, disk starts being used excessively (here I can close Chrome or not, no matter, the disk won't stop) Disk diod is on all the time and I hear it running like crazy, all computer is a little slowed down It last 5-10 minutes In the meantime, I go to Windows Task Manager and observe what processes are using disk and turn them off one by one - but no success in stopping the excessive disk usage After approximately 10 minutes everything stops I go to Chrome (or re-open it) and refresh the page with mixed results - sometimes the whole process repeats immediately, sometimes not Basically, it is almost always Chrome refreshing random page that starts the excessive disk usage, but killing Chrome process does not stop the disk. Going to the same page in Firefox is not causing problems. Windows Search is turned off. I would like to know what is really happening. Perhaps there is a utility which would allow me to see which process is really using the disk, so that I can disable the service ? (not chrome, because killing chrome does not change anything) or even better, perhaps there is a way to fix it?

  Read the article

• Safe use of Update-FormatData?

  - by Steve B

  In a custom PowerShell module, I have at the top of my module definition this code: Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") This is working fine as all .ps1xml files are loaded. However, the module is sometimes loaded using Import-Module MyModule -Force (actually, this is in the install script of the module). In this case, the call to Update-FormatData fails with this error : Update-FormatData : There were errors in loading the format data file: Microsoft.PowerShell, c:\pathto\myfile.Types.ext.ps1xml : File skipped because it was already present from "Microsoft.PowerShell". At line:1 char:18 + Update-FormatData <<<< -AppendPath "c:\pathto\myfile.Types.ext.ps1xml" + CategoryInfo : InvalidOperation: (:) [Update-FormatData], RuntimeException + FullyQualifiedErrorId : FormatXmlUpateException,Microsoft.PowerShell.Commands.UpdateFormatDataCommand Is there a way to safely call this command? I know I can call Update-FormatData with no parameters, and it will update any known .ps1xml file, but this would work only if the file has already been loaded. Can I list somewhere the loaded format data files? Here is a bit of background: I'm building a custom module that is installed using a script. The install script looks like : [CmdletBinding(SupportsShouldProcess=$true,ConfirmImpact="High")] param() process { $target = Join-Path $PSHOME "Modules\MyModule" if ($pscmdlet.ShouldProcess("$target","Deploying MyModule module")) { if(!(Test-Path $target)) { new-Item -ItemType Directory -Path $target | Out-Null } get-ChildItem -Path (Split-Path ((Get-Variable MyInvocation -Scope 0).Value).MyCommand.Path) | copy-Item -Destination $target -Force Write-Host -ForegroundColorWhite @" The module has been installed. You can import it using : Import-Module MyModule Or you can add it in your profile ($profile) "@ Write-Warning "To refresh any open PowerShell session, you should run ""Import-Module MyModule -Force"" to reload the module" Import-Module MyModule -Force Write-Warning "This session has been refreshed." } } MyModule defines, as first statement, this line : Update-FormatData -AppendPath (Join-Path $psscriptroot "*.ps1xml") As I updated my $profile to always load this module, the Update-Path command has been called when I run the install script. In the install script, I force import the module, which be fire again the module, and then, the Update-Path call

  Read the article

• How to Upgrade PHP 5.2 to 5.3 on Windows Plesk Panel 8.2

  - by Jagat Sheth

  I need to upgrade my server PHP version becasue of Wordpress New version not support PHP 5.2. On My server windows 2003 stansard edition x64 with SP1 installed, IIS 6.0, MySQL 4.1, Plesk Panel 8.2. I have follow listed steps on plesk KB. http://kb.parallels.com/6670 How to update PHP 5 on a Windows server with Parallels Plesk Control Panel 8.x and 9.x installed. In order to upgrade PHP 5 to the necessary version (other than shipped with Parallels Plesk), please perform the following steps: Stop Plesk services (‘Control Panel’ and all that are included in the ‘Plesk Run-Time’ section) Rename folder %plesk_dir%\Additional\PleskPHP5 to the orig_PleskPHP5 Create a new folder %plesk_dir%\Additional\PleskPHP5 Download necessary version of PHP, unzip its content, and copy it to the newly created folder PleskPHP5 Copy the file php.ini from the old folder orig_PleskPHP5 to the new one Make sure the permissions are inherited Start Plesk services Click the "Refresh" button in the Components Management section in Parallels Plesk Panel and check if you can see the new PHP version there After follow steps when I open a PHP info it shows me specified module could not be found. If anybody know solution Kindly help me is highly priority. I am very thankful if any one help me to solve this ASAP. Thanks and regards, Jagat Sheth

  Read the article

• HAProxy, health checking multiple servers with different host names

  - by Marco Bettiolo

  I need to load balance between multiple running servers with different host names. I cannot set-up the same virtual host on each one. Is it possible to have only one listen configuration with multiple server and make the Health Checks apply the http-send-name-header Host directive? I am using HAProxy 1.5. I came up with this working haproxy.cfg, as you can see, I had to set a different hostname for each health check as the health check ignores the http-send-name-header Host. I would have preferred to use variables or other methods and keep things more concise. global log 127.0.0.1 local0 notice maxconn 2000 user haproxy group haproxy defaults log global mode http option httplog option dontlognull retries 3 option redispatch timeout connect 5000 timeout client 10000 timeout server 10000 stats enable stats uri /haproxy?stats stats refresh 5s balance roundrobin option httpclose listen inbound :80 option httpchk HEAD / HTTP/1.1\r\n server instance1 127.0.0.101 check inter 3000 fall 1 rise 1 server instance2 127.0.0.102 check inter 3000 fall 1 rise 1 listen instance1 127.0.0.101:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.example.com server www.example.com www.example.com:80 check inter 5000 fall 3 rise 2 listen instance2 127.0.0.102:80 option forwardfor http-send-name-header Host option httpchk HEAD / HTTP/1.1\r\nHost:\ www.bing.com server www.bing.com www.bing.com:80 check inter 5000 fall 3 rise 2

  Read the article

• Google Apps: MX records for zonefile

  - by 23tux

  Hi everybody, I have a question about using Google Apps for handling emails. I don't want to set up a whole entire mail system on my server, so I decided to use Google Apps. The ownership of my domain is approved, and now I'm trying to change the MX records in the zone file of my domain. But I think I'm doing wrong, it doesn't work. I want to use mail.mydomain.com as a adress to the mail server for POP, SMTP and IMAP. My zone file looks like this: $TTL 86400 @ IN SOA ns1.first-ns.de. postmaster.robot.first-ns.de. ( 2011011700 ; serial 14400 ; refresh 1800 ; retry 604800 ; expire 86400 ) ; minimum @ IN NS robotns3.second-ns.com. @ IN NS robotns2.second-ns.de. @ IN NS ns1.first-ns.de. @ IN A 111.111.111.111 localhost IN A 127.0.0.1 www IN A 111.111.111.111 ftp IN CNAME www loopback IN CNAME localhost mail IN CNAME @ relay IN CNAME www @ IN MX 10 ALT1.ASPMX.L.GOOGLE.COM. @ IN MX 10 ASPMX3.GOOGLEMAIL.COM. @ IN MX 10 ASPMX2.GOOGLEMAIL.COM. @ IN MX 10 ASPMX.L.GOOGLE.COM. @ IN MX 10 ALT2.ASPMX.L.GOOGLE.COM. I hope someone can figure out, what's wrong with this configuration. When I start a ping on mail.mydomain.org I get an answer from 111.111.111.111 and not from the google server ALT1.ASPMX.L.GOOGLE.COM. thx, tux

  Read the article

• krenew command not working : Permission Denied

  - by prathmesh.kallurkar

  I am using a Linux server to perform my simulations. The login and the file-system of the server are protected using kerberos. The file-system is supported using NFS. Since my simulations take a lot of time to run, my ssh sessions used to hang regularly. So, I have started running my simulations in byobu (similar to screen). In order to make sure that my kerberos session remains active, I am using the krenew command. I have entered the following command in my .bash_profile file. (I am sure that it is called for every login) killall -9 krenew 2> /dev/null krenew -b -t -K 10 So everytime I ssh to the server, I kill the existing krenew command. Then, I spawn a new krenew command -b (which runs in background), -t (I forgot why I was using this option !), and -K 10 (It must run after every 10 minutes and refresh the kerberos cache). When I run the simulations, It runs for 14 hours and then suddenly, I am getting error for reading file Permission Denied Is the command that I am running incorrect ??

  Read the article

• 1080p monitor: connected through VGA - perfect, HDMI - awful

  - by develroot

  When I connect my 23" monitor (1920x1080) to my pc through HDMI, I encourage some problems. It's not full screen That's it. There are ~1cm black borders on right and left side and ~0,5cm black borders on the top and the bottom of the monitor. That's pretty frustrating. I tried adjusting overscan, but I can't mannualy type the % of overscan that I need. I can only select between ex. 8 and 10% in AMD Vision Engine Control center, but what I need is 9%. Next, even if i select 10% and the image fits all the corners, but after log off all the settings are lost and I have to do it again and again. Text, images, everything looks blurry That surprised me a lot. Should'nt HDMI quality be better than VGA's one? When connected through HDMI, the text isn't readable. It's like a very low refresh rate, although i'm running at 60Hz. Also the text has something like little shadows, very very annoying. Are there any tips to get the same quality as with VGA, with HDMI ? (running on integrated ATI Radeon HD4200, which, appearently, is the best card I have ever seen in terms of integrated ones)

  Read the article

• Running .NET code in XML file [closed]

  - by Stuart McIntosh

  We have 2 servers, 1 already configured with .net which works fine and a new one which appears to be configured the same but when I open an xml page in Internet Explorer it complains about the <% tag. We have IIS on win srvr 2003 SP2. The website is configured with .NET 1.1.4322. In ISAPI extensions have set the .XML extension to use c:\windows\microsoft.net\framework\v1.1.4322\aspnet_isapi.dll But the page: <property name="documentmaxage" value="0"/> <property name="documentmaxstale" value="0"/> <var name="m_Prompt_Path" /> <form id="InitVoiceXmlDoc"> <block> <assign name="m_Prompt_Path" expr="&quot;<% Response.Write(Request.QueryString["m_Prompt_Path"]); %>&quot;"/> </block> </form> gives the error: The XML page cannot be displayed Cannot view XML input using XSL style sheet. Please correct the error and then click the Refresh button, or try again later. The character '<' cannot be used in an attribute value. Error processing resource 'http://localhost:11119/fails.xml'. Lin... &quo... We have the same config on another server which works fine. So are there other options apart from the ISAPI extensions that I need to look at

  Read the article

• How to calculate unweighted averages in Excel PivotTable?

  - by yonatron

  I often make PivotTables in which each row contains a number of per-person average measures. I then want to look at the unweighted column average for each measure, and usually make some kind of chart from these. Because my individual cells are often averaged from different numbers of data points, the Grand Total row ends up being a weighted average, which I’m not interested in. So I usually make my own average row a few rows above the table to use for my charts. That’s not too much work, but there’s another problem. I often add a few more people’s worth of data to the PivotTables’ source, then refresh the tables. This means my average row needs to be updated to encompass more rows from the PivotTable. Not a huge deal with one table, but when I have lots of them across lots of sheets, I have to do find/replace on a whole bunch of formulas. So: is there a way to automatically get unweighted column averages in a PivotTable, such that when the table is refreshed, the averages don’t change locations and encompass the newly added (or removed) data Thanks

  Read the article

• Internet connection problem,ping ok , but outlook and browsers dont work

  - by Ashian

  Hi, From some days ago I have a big problem on my laptop( run windows xp sp3) When I connect to internet I can ping web sites but when try to browse them some times it work correctly and some times the connection to server intrupted and I have to refresh the page several times. in this case browser show a connection problem immediatly after I click on address bar or a link on page( wihtout any try to connect to server) I use FireFox and opera and both of them have this problem. try another ISP and still I have this problem. I didnt use any proxy server and check the proxy setting. In this case Outlook also can't connect to mail server. this problem anfter some time or after restart windows have been fixed for a while. I check for virus and can't find anything. Is there any idea how can I fix it? UPDATE: Thanks for your responses. I test them , also I use Open DNS setting and that dosent help me. last night I see that my local web application ( such as Adsl modem config web site , and sites that I set up on windows xo IIS ) aslo can't open and Internal Communication error apears ( Opera Message) that didnt relate to DNS settings or Internet connection.

  Read the article

• ASP.Net Session Timing Out Rapidly

  - by Zac

  We have an ASP.Net 3.5 website running on Windows Server 2008 with IIS7. The session timeout period for this site is configured to be 20 minutes - however, it is currently lasting for between 40 and 50 seconds. After researching the problem we investigated several configuration values which could be involved in the timeout period but none of them are set to less than 20 minutes. The areas we look are as follows: web.config system.web/sessionState element (20 minutes). web.config system.web/authentication/forms element (not present, defaults to 30 minutes). Sites/{website}/ASP/Session Properties/Time-out (20 minutes). Application Pools/{appPool}/Advanced Settings/Process Model/Idle Time-out (20 minutes). We've also noted that the CPU is staying around 0% and that RAM usage is flat-lining around 1.07 GB (of 8 GB available) - so there is no performance-based reason for IIS to be recycling the Application Pool as far as we can tell. Are there any settings we've overlooked which could cause the session timeouts to be expiring so quickly? EDIT A couple of additional points: This is not occurring in development, only on the server. The session is not sliding (i.e. if we refresh the page a few times it still times out approximately 40 - 50 seconds after the session was created.

  Read the article

< Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >