Search Results

Search found 10748 results on 430 pages for 'disk encryption'.

Page 384/430 | < Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >

• Will these instructions work when turning of journaling on an ext4 SSD?

  - by snowlord

  I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

  Read the article

• Boot drive not found issue after cloning using Apricorn EZgig

  - by TomWilsonFL

  A couple days ago I cloned a drive for someone using the EZgig software. Usually this goes without a hitch, but this particular drive I was cloning is quite old. When I restarted with the new drive I received the typical bootable disk not found message, so I turned it off, messed with the BIOS, restarted and it came up fine. That night I was working remotely on the computer and had to restart it. It didn't come back up; not a good sign. When the user came to the computer in the morning it was giving the same message. I have found that to make the computer boot, all I have to do is go into the BIOS and "Load Defaults", then restart. It will boot and runs great. Any thoughts on what is causing this situation? Is it MBR corruption? Are some settings being saved in the CMOS? A couple points of mention: I have already attempted looking for a BIOS update for the computer, but the newest is already installed (from 2003). When the computer reboots it either shows "None" for Primary Master, or sometimes it will just not show anything. Thanks, Tom

  Read the article

• How to migrate WinXP from failing old HD to new one

  - by Péter Török

  Following this issue, we have all our important data backed up now. I also bought and installed a new replacement hard disk (WD 160GB PATA) as secondary (slave) drive. I created two primary NTFS partitions on it: a 40 GB system partition, and a 110GB data partition. In theory I could start reinstalling WinXP from scratch on the new system partition, then copying over all user data from the old drive to the new data partition. Once this is done, I could even throw away the old drive, or keep it just to see what happens. (Note: I don't want to clone the whole drive as it contains a dual boot setup with an old Linux installation which I don't need anymore, and anyway, a fresh reinstall would do WinXP good to get rid of many years' clutter.) However, I am lazy :-) The old HD is still functioning, the problem has not manifested again since. So I feel there is no need to hurry with a complete OS reinstall. What I don't know though is whether I will be able to install WinXP on the new system partition at a later stage without affecting the contents of the data partition on the same drive. If this is possible, I can just move over all our data to the new data partition to have it safe, then continue running WinXP from the old drive as long as it works. Does anyone see any problems/risks with this plan?

  Read the article

• Empty rewrite.log on Windows, RewriteLogLevel is in httpd.conf

  - by ripper234

  I am using mod_rewrite on Apache 2.2, Windows 7, and it is working ... except I don't see any logging information. I added these lines to the end of my httpd.conf: RewriteLog "c:\wamp\logs\rewrite.log" RewriteLogLevel 9 The log file is created when Apache starts (so it's not a permission problem), but it remains empty. I thought there might be a conflicting RewriteLogLevel statement somewhere, but I checked and there isn't. What else could cause this? Could this be caused by Apache not flushing the log file? (I closed it by hitting CTRL-C on the httpd.exe command ... this caused the access logs to be flushed to disk, but still nothing in rewrite.log) My (partial) httpd-vhosts.conf: <VirtualHost *:80> ServerAdmin webmaster@localhost ServerName my.domain.com DocumentRoot c:\wamp\www\folder <Directory c:\wamp\www\folder> Options -Indexes FollowSymLinks MultiViews AllowOverride None Order allow,deny allow from all <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule . everything-redirects-to-this.php [L] </IfModule> </Directory> </VirtualHost>

  Read the article

• Formatting a memory stick with two partitions?

  - by Marius

  I have a 16GB memorystick which used to have a Linux partition. It therefore has two partitions; 2GB FAT32 and 14GB linux boot drive. The linux part stopped working, so I decided to reinstall it. But windows can't see that partition. I tried formatting the whole disk, but I can only format one partition (the FAT32). There seems to be no way to combine the two partitions into one big one, and there seems to be no way for windows to partition the large part of the memorystick to but Linux on it. In the windows partition manager, windows sees the large unused partition, and it let me delete it. But once I have deleted it, I'm not allowed to format it. Also I cannot delete or resize the small partition. So, to summarize: I have a memorystick with two partitons. Windows only sees one of them, and won't let me use the other one. I would like to combine the two partitions so I can install Linux on the memory stick again.

  Read the article

• virtual machines, dual booting and data disks on SSD

  - by stevemarvell

  This is in planning, so if I've got the strategy wrong, please let me know. There are multiple questions here, but I think they all degenerate to the same answers. The hardware is a laptop with a single SSD. I'm trying to not lose the performance of the SSD. I plan a native dual booting Windows (plus cygwin) and Linux machine which is my BYOD and represents the development environment. I keep the codebase on a shared partition (though sometimes this is an external thunderbolt SSD) which can be natively "mounted" by whichever OS is in operation. I boot into one or the other environments depending on the task in hand. Sometime I have to develop with windows tools, but generally, Linux is my preferred development environment. It would be ideal if I could VM the other OS and run either in either. I'm going to assume, because I've not found a sensible VM based solution, that I have get samba involved to share the code partition between VMs. Is this going to blow my SSD performance in the VM? The client also supplies me with a VM for the target environment, usually linux. This is not often suited to development and is used for testing only. I normally keep two copies of this, one as a sandbox and one which I deploy to using the client's preferred method. I keep these VM snapshots on the shared partition. The latter is interacted with over the network and so has no disk sharing requirements. However, it would be useful for the sandbox to be able to "mount" the code base from the natively running OS. Is this samba or nfs again, depending on the native OS? Am I missing a trick which allows this to all work smoothly with all four environments running at once without loosing the SSD performance?

  Read the article

• How to stop Firefox on an SSD from freezing when using the search box or submitting a form?

  - by sblair

  Firefox usually freezes for about a second whenever I search for something from the toolbar search box, when submitting a form, or when clearing the search box history. I suspect it has something to do with the auto-complete feature. Using Windows 7's Resource Monitor, the problem seems to be from the file: C:\Users\<username>\AppData\Roaming\Mozilla\Firefox\Profiles\<profile>\formhistory.sqlite-journal I believe this is a temporary file which caches database writes. The following screenshot shows the very high response times from six different searches, and that the queue length on drive C shoots off the scale: My Firefox profile is on an Intel X25-M G2 SSD. The problem doesn't seem to occur if I create a new profile on a hard disk drive. However, I'd like to know why the problem exists on the SSD in the first place (because it's an annoying problem which contradicts the reason I bought an SSD, and it might happen with other applications too), and how to prevent it. It still occurs if Firefox is started in safe mode, and with the recent beta versions. Updates: VACUUMing the Firefox profile databases does not help with this problem. The SSD Optimizer in the Intel SSD Toolbox does not help either.

  Read the article

• Windows 7 starts getting sluggish over a few days

  - by munrobasher

  Myself and the other developer are running Windows 7 Enterprise 64 bit with 8GB RAM on different Gigabyte motherboards with Quad core Intel CPUs. Most of the time, it runs like a dream. We use VMware workstation a lot (hence the 8GB) and that works well. Except... now and then, after the PCs have been on for a few days, the whole system starts getting really sluggish doing certain tasks. The other's developer's system is far worse than mine with it taking up to a minute to launch IE. Today, mine has gone sluggish but nowhere near as bad. For example, normally when I click on a new tab in IE, it's instant. Today, there's an obvious delay. Right-clicking in this window to trigger iSpell is normally instant, right now it takes about five seconds. I've got resource monitor open on my second monitor and when I did that right-click, there was no obvious peak in CPU, disk or memory. A reboot does fix it so it does sound like a resource issue but haven't a clue what might be to blame. The two computers have similarities (same spec) but also differences (like motherboard, RAM & CPU models). So I guess the question is, any pointers on diagnosing why a PC is sluggish? What could cause such a right-click slow down in IE for example? It sounds like such a simple operation. NOTE: whilst typing this message alone, it was fine performance wise. I can click around the page no problem but right-click still is noticeable slow. Will reboot over lunch... Cheers, Rob.

  Read the article

• What is the best private cloud storage setup

  - by vdrmrt

  I need to create a private cloud and I'm searching for the best setup. These are my 2 most important requirements 1. Disk and system redundant 2. Price / GB as low as possible The system is going to be used as backup setup which will receive data 24/7 over SFTP and rsync. High throughput is not that important. I'm planning to use glusterfs and consumer grade 4TB hard-drives. I have worked out 3 possible setups 3 servers with 11 4TB HDD Setup up a replica 3 glusterfs and setup each hard drive as a separate ext4 brick. Total capacity: 44TB HDD / TB ratio of 0.75 (33HDD / 44TB) 2 servers with 11 4TB HDD The 11 hard-drives are combined in a RAIDZ3 ZFS storage pool. With a replica 2 gluster setup. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) 3 servers with 11 4TB consumer hard-drives Setup up a replica 3 glusterfs and setup each hard-drive as a separate zfs storage pool and export each pool as a brick. Total capacity: 32TB (+ zfs compression) HDD / TB ratio of 0.68 (22HDD / 32TB) (Cheapest) My remarks and concerns: If a hard drive fails which setup will recover the quickest? In my opinion setup 1 and 3 because there only the contents of 1 hard-drive needs to be copied over the network. Instead of setup 2 were the hard-drive needs te be reconstructed by reading the parity of all the other harddrives in the system. Will a zfs pool on 1 harddrive give me extra protection against for example bit rot? With setup 1 and 3 I can loose 2 systems and still be up and running with setup 2 I can only loose 1 system. When I use ZFS I can enable compression which will give me some extra storage.

  Read the article

• How do I force a restore over an existing database?

  - by Ian Boyd

  I have a database, and i want to force a restore over top of it. I check the option: Overwrite the existing database (WITH REPLACE) But, as expected, SSMS is unable to overwrite the existing database. Of course i don't want different filenames; i want to overwrite the existing database. How do i force a restore over an existing database? And for Google search crawler: File '%s' is claimed by '%s'(4) and '%s"(3). The WITH MOVE clause can be used to relocate one or more files. RESTORE DATABASE is terminating abnormally. (Microsoft SQL Server, Error: 3176) Update The script (before i deleted the database, because i needed to get it done) was: RESTORE DATABASE [HealthCareGovManager] FILE = N'HealthCareGovManager_Data', FILE = N'HealthCareGovManager_Archive', FILE = N'HealthCareGovManager_AuditLog' FROM DISK = N'D:\STAGING\HealthCareGovManager10232013.bak' WITH FILE = 1, MOVE N'HealthCareGovManager_Data' TO N'D:\CGI Data\HealthCareGovManager.MDF', MOVE N'HealthCareGovManager_Archive' TO N'D:\CGI Data\HealthCareGovManager.ndf', MOVE N'HealthCareGovManager_AuditLog' TO N'D:\CGI Data\HealthCareGovManager.ndf', MOVE N'HealthCareGovManager_Log' TO N'D:\CGI Data\HealthCareGovManager.LDF', NOUNLOAD, REPLACE, STATS = 10 I used the UI to delete the existing database, so that i could use the UI to force an overwrite of the (non)existing database. Hopefully there can be an answer so that the next guy can have an answer. No, nobody was in the context of the database (The error message from other connections is quite different from this error, and i only got to see this error after i killed the other connections).

  Read the article

• Should I keep my ex-employer's data?

  - by Jurily

  Following my brief reign as System Monkey, I am now faced with a dilemma: I did successfully create a backup and a test VM, both on my laptop, as no computer at work had enough free disk space. I didn't delete the backup yet, as it's still the only one of its kind in the company's history. The original is running on a hard drive in continuous use since 2006. There is now only one person left at the company, who knows what a backup is, and they're unlikely to hire someone else, for reasons very closely related to my departure. Last time I tried to talk to them about the importance of backups, they thought I was threatening them. Should I keep it? Pros: I get to save people from their own stupidity (the unofficial sysadmin motto, as far as I know) I get to say "I told you so" when they come begging for help, and feel good about it I get to say nice things about myself on my next job interview Nice clean conscience Bonus rep with the appropriate deities Cons: Legal problems: even if I do help them out with it, they might just sue me for keeping it anyway, although given the circumstances I think I have a good case Legal problems: given the nature of the job and their security, if something leaks, I'm a likely target for retaliation Legal problems: whatever else I didn't think about I need more space for porn. Legal problems. What would you do?

  Read the article

• Photoshop CS5 performance over network drive (cifs)

  - by grub

  Hello Everyone I did install a QNAP NAS TS410 for a customer (professional photographer) with 3 Hitachi Deskstar 7200rpm 2TB disk configured as RAID5. The NAS and the workstations are connected over a Gigabit network. He and his co-worker are accessing the photos (about 1TB of photos) over a mapped network drive from their windows machines (Windows XP - 32bit and Windows 7 Ultimate - 32bit). Both are using Photoshop CS5 to edit the photos. The problem is that to save a edited photo takes a really long time, it takes about 3 times as long to save a photo as to open it. After some tests I can exclude the network, the NAS and the windows machines as source of the issue. I think the problem is the Photoshop software and its handling of the network drives. Officially network drives are not supported by Adobe. I do not have any experience with the Adobe products, especially with Adobe Photoshop CS5. What are your recommendation to solve the performance issue? Should my customer copy the photos to the local drive, edit them and upload them again to the network drive or is Adobe Drive or Adobe Version Cue the answer? One requirement is that the photos need to be accessible / editable from both computers even when one of them is offline. Adobe Version Cue needs a dedicated service running to be usable, so this solution is not possible as far as I understand the Cue software. Thank you for your input to this issue and have a nice day :-) Greetings grub

  Read the article

• Flash Backed Write Cache (FBWC) without capacitor pack

  - by Martyn

  I brought a HP Smart Array P410 controller and it is installed and working fine in a HP Prolient Microserver with 4 drives in two RAID 1 arrays. I didn’t realise however that it came without any cache so would only work by directly writing straight to the disk, and the performance was horrible. So I then brought the 512MB Flash Backed Write Cache (FBWC) memory module as I was under the impression that with FBWC I would not need a battery. I got this idea from a forum post. "What do you guys think of the choice between 'BBWC' (battery backed write cache) and 'FBWC' (flash backed write cache)? The flashed based ones use non-volitile memory so need no battery." After installing the cache module however the server pretty much won’t boot. The P410 has a flashing amber light on it, and from the manual that doesn’t sound good. I’ve managed to get to the on board BIOS once and even managed to get to boot to the HP Array Configuration Utility (ACU) CD once, but every other time the Server continuingly reboots once it get to the POST screen and reads ARRAY INITILIZING %%%. The one time I reached the ACU, it reported a problem with the Cache Module. To me, it seems like the cache module is faulty, however the supplier tells me “Do you have an FBWC battery pack, p/n 587324-001, because that is required for the cache to work. If you have it, please complete an RMA form and we'll send a replacement / credit.” Does this sound right to you? I’ve been ordering the parts from the US and I don’t want to spend $77 + $40 p&p on a battery, wait a week for the shipping to find the card is faulty, and I don’t want to send back a working card?

  Read the article

• Why is windows not able to create a system partition?

  - by hughes

  I'm reinstalling Windows 7 64 bit, and I encountered an issue I've never seen before. I have a legit copy of Win 64 Professional, and I've installed it probably a half dozen times on this machine in the past without a problem. Googling the error only brings me to issues with people who are upgrading to win7. The drive itself seems to not have a problem. I can mount it on other systems and I can create an NTFS partition on it on other machines. I can install Ubuntu on it without any issues. Additionally, if I try using my alternate backup hard drive, the installer gives the same error. I have run diskpart from the setup page and clean seems to report that all is well. However, I cannot get past the screen below, which says Setup was unable to create a new system partition or locate an existing system partition. This happens regardless of whether or not the disk space is already allocated. What is causing this? How do I solve or get past this?

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• Weird Apache behaviour and with files again

  - by afifio

  Hi and thanks for stopping by. I have read Weird Apache problem with file, I have read Weird Apache problem with file ...and its not the problem Setup single XAMPP installation on Windows, single windows user, 2HD, 1 is a portable USB. All is fine, until I move the xampp to new portable HD Symptom Old php files - works fine, new one doesnt http://127.0.0.1/Ajax/index.php - yay http://127.0.0.1/test2/t.php - display the source code http://127.0.0.1/Ajax/test2/t.php - display the source code http://127.0.0.1/Ajax/t.php - display the source code Extra Info IIS+MS Web Development stuff, .NET4, Asp, etc is being installed and still hast reboot yet. .htaccess also seems doesnt work Apache2 conf file was modified to Averride All and still it doesnt care. One of the directory supposed to treat .htm as php yet got text, created another directory and edit a phpinfo, still another text, browse to phpmyadmin, viola, works fine Suspect Does Apache honour XP security and permission ? If so, this is a single user computer. Does Apache dont like my new hard disk/new place ? Why it doesnt execute the php in new directory but happily execute in old folder ? Thanks for the riddle answers

  Read the article

• Ubuntu 9.04: Ripping CDs with grip?

  - by chris

  I tried to rip a CD tonight, and couldn't figure out how to configure grip - /dev/cdrom doesn't seem to be the mount point for music CDs any more. How can I configure grip to find CDs? Update: /etc/fstab has /dev/scd0 /media/cdrom0 udf,iso9660 user,noauto,exec,utf8 0 0 But there's nothing visible in /media/cdrom0 (or /media/cdrom, which is a symlink to cdrom0) There's an icon on the desktop labeled "Audio Disk" and opening it shows the .wav files on the CD. The location is cdda://sr0/, but grip doesn't like that either. Trying to manually mount /dev/sr0, I get $ sudo mount -t auto /dev/sr0 foo/ mount: block device /dev/sr0 is write-protected, mounting read-only mount: you must specify the filesystem type Update 2: Tried to change the media handling preferences (From a file browser, Edit-Preferences, Media, CD Audio) to "Do Nothing". CD Still doesn't mount. Update 3: With an audio CD in the drive: $ ls -l /dev/ | grep cd lrwxrwxrwx 1 root root 3 2009-09-15 22:13 cdrom1 -> sr0 lrwxrwxrwx 1 root root 3 2009-09-15 22:13 cdrw1 -> sr0 drwxr-xr-x 2 root root 60 2009-09-15 22:13 pktcdvd lrwxrwxrwx 1 root root 3 2009-09-15 22:13 scd0 -> sr0 crw-rw----+ 1 root cdrom 21, 2 2009-09-15 22:13 sg2 brw-rw----+ 1 root cdrom 11, 0 2009-09-15 22:13 sr0

  Read the article

• "What happens?" server performance monitor

  - by AlexAtNet

  Hello! After reviewing some thread about server monitoring software I end up with a simple question: Which of the server monitoring tools should I use for automatic detection of "abnormal" situations with recommendations on how to fix them? I look for software that checks the system performance after installation and calculate some average load values (memory, CPU, etc). And when something happens (CPU load is increased to 20%) then it tries to detect a reason for this. If it is apache, it should check for access logs. If mysql, it should check mysql logs and tell me what happens. It this is because some user decodes a lot of images, I'd like to know which command is executed, when and user name. The same for disk usage, memory, number of processes, threads and so on. Ideally, this software should periodically checks the system and report problems: errors in PHP error log, outdated packages, security vulnerabilities. In other word I'm looking a software that will keep my simple Debian/Apache/PHP/MySQL server without forcing me to monitor the charts every day. I hope that such program exists. Thanks, Alex

  Read the article

• Old scheduled task still being started, but can't find it.

  - by JvO

  System: Windows XP Home Summary: Some scheduled task is still being started by Windows, but I can't find it, nor determine where its configuration has been stored. This is turning into a mystery for me... I set up a Windows XP Home machine to run a task at 7:00 AM, using the Task manager. This was a clean install, no users defined, so you got straight to the desktop after starting the machine. The filesystem uses NTFS. Later on, I needed to introduce users, so I created one (named Sam) with administrator privileges. After this I noticed that the scheduled task failed, most likely due to privilege errors (i.e. can't write to a network drive). So I want to delete the old task, and add it again with the correct user credentials. However.... I can't find the old task!! I know it is still being executed at 7:00 AM, but there's no mention anywhere on the system of this task. I've looked in c:\windows\tasks for .job files, but there's only the "MP Scheduled Scan.job" from Security Essentials. I've searched the whole disk for mention of the batch file that is being run, but can't find it. So why is this old task still running, and more importantly, why can't I find it? Would it have something to do with introducing users on XP?

  Read the article

• What's throttling the database?

  - by Troels Arvin

  Hardware: Intel x86_64 with 192GB of RAM. OS: CentOS 5.4 x86_64. DBMS: DB2 v. 9.7.1 64 bit. During certain special workloads (e.g. parallel REORGs/RUNSTATs), I've seen the server transporting 450MB/s with 25000IO/s (yes, there is probably some storage system caching happening here) while all CPU cores were happily working in an even mix of usermode/wait. And disk benchmark tools can also bring some very satisfying bandwith and IO/s numbers to the table. On the other hand, we also have another scenario: A single rather complex query with at least one large table scan. db2's "list applications" reports that the query is Executing (not locked). IO: At most 10MB/s, 500 IO/s; CPU: two cores in 99.9% wait state, all other cores 100% idle. The tables which the query reads from have been altered to have LOCKSIZE=TABLE, so I would think that lock list work is zero. What's going on in such a situation? What tools/snapshots/... can I use to gain better insight in such a case?

  Read the article

• Windows based development environment: HyperV, VMWare, or VirtualBox on development machine?

  - by bleepzter

  I am a software engineer with a little bit of an informal "support" functionality... I am trying to figure out what is the best possible approach to employing virtualization technologies into our development process. Since the code we develop is server-centric, testing it often requires a VM with specific software requirements. I used to use VM Ware player (free version) to run my VM's until both of my laptops started exhibiting issues with corrupted windows 7 services and dying hard drives. All leads pointed to VMWare, which by the way seems to be a solid product if you pay for the Workstation edition ($300). On a side note, I have always been a fan of the Windows Server product line. I think it makes for one of the best development environments out there - it is highly scalable, highly reliable, and very efficient. So to be fair I replaced the drives of the laptops and installed Windows Server 2008R2, VS2010 Ultimate SP1, SQL Server 2008R2, TFS Server 2010 and all other tools and API's needed do do my work properly. So now I am stuck with a bunch of VMWare VMs. I don't want to repeat of what happened before, and I certainly don't want to bog down my machine with an inefficient hypervisor or services that are not needed. Futhermore the VMDK hard-disk format used by VMWare is not compatible with the VHD format of Hyper V. It is my understanding that converting from one format to the other can only happen by Microsoft System Center Virtual Machine which I have downloaded from MSDN and ready to install. I guess the question at this point is: Does SCVM run as another service in Windows? Is it a memory hog? What is a better virtualization technology - Hyper-V or Virtual Box in terms of efficiency ease of use and most importantly - memory footprint? (Keep in mind the development environment already has a ton of services running such as TFS Server, SQL Server, IIS, etc...) How would you advise to proceed at this point so that the VMs are still used in the test process? Thanks Martin

  Read the article

• How can I upgradge from Ubuntu Intrepid Ibex 8.10 to Jaunty 9.04 when old-releases no longer has the necessary packages?

  - by tommy chheng

  I changed my sources.list to: deb http://old-releases.ubuntu.com/ubuntu/ intrepid main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/ intrepid-updates main restricted universe multiverse deb http://old-releases.ubuntu.com/ubuntu/ intrepid-security main restricted universe multiverse I tried installing sudo apt-get install update-manager-core but i get this error: 1 upgraded, 3 newly installed, 0 to remove and 40 not upgraded. Need to get 2506kB/2555kB of archives. After this operation, 4346kB of additional disk space will be used. Do you want to continue [Y/n]? Y Err http://old-releases.ubuntu.com intrepid-updates/main update-manager-core 1:0.93.34 404 Not Found Err http://old-releases.ubuntu.com intrepid-security/main dpkg 1.14.20ubuntu6.3 404 Not Found Failed to fetch http://old-releases.ubuntu.com/ubuntu/pool/main/d/dpkg/dpkg_1.14.20ubuntu6.3_amd64.deb 404 Not Found Failed to fetch http://old-releases.ubuntu.com/ubuntu/pool/main/u/update-manager/update-manager-core_0.93.34_amd64.deb 404 Not Found E: Unable to fetch some archives, maybe run apt-get update or try with --fix-missing? Running apt-get update or --fix-missing returns the same errors. How can I successfully upgrade from Intrepid Ibex to Jaunty 9.04?

  Read the article

• NFS-shared file-system is locking up

  - by fredden

  Our NFS-shared file-system is locking up. Please feel free to ask any questions you feel relevant. :) At the time, there are a lot of processes in "disk sleep" state, and the load averages on our machines sky-rocket. The machines are responsive on SSH, but our the majority of our websites (apache+mod_php) just hang, as does our email system (exim+dovecot). Any websites which don't require write access to the file-system continue to operate. The load averages continue to rise until some kind of time-out is reached, but for at least 10-15 minutes. I've seen load averages over 800, yet the machines are still responsive for actions which don't require writing to the shared file-system. I've been investigating a variety of options, which have all turned out to be red-herrings: nagios, proftpd, bind, cron tasks. I'm seeing these messages in the file server's system log: Jul 30 09:37:17 fs0 kernel: [1810036.560046] statd: server localhost not responding, timed out Jul 30 09:37:17 fs0 kernel: [1810036.560053] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:37:17 fs0 kernel: [1810036.560064] lockd: cannot monitor node2 Jul 30 09:38:22 fs0 kernel: [1810101.384027] statd: server localhost not responding, timed out Jul 30 09:38:22 fs0 kernel: [1810101.384033] nsm_mon_unmon: rpc failed, status=-5 Jul 30 09:38:22 fs0 kernel: [1810101.384044] lockd: cannot monitor node0 Software involved: VMWare, Debian lenny (64bit), ancient Red Hat (32 bit) (version 7 I believe), Debian etch (32bit) NFS, apache2+mod_php, exim, dovecot, bind, amanda, proftpd, nagios, cacti, drbd, heartbeat, keepalived, LVS, cron, ssmtp, NIS, svn, puppet, memcache, mysql, postgres Joomla!, Magento, Typo3, Midgard, Symfony, custom php apps

  Read the article

• Replace Linux Boot-Drive | ext3 to btrfs

  - by bardiir

  I've got a headless server running Debian Linux currently. Linux vault 3.2.0-3-686-pae #1 SMP Mon Jul 23 03:50:34 UTC 2012 i686 GNU/Linux The root filesystem is located on an ext3 partition on the main harddrive. My data is located on multiple harddrives that are bundled to a storage pool running with btrfs. UUID=072a7fce-bfea-46fa-923f-4fb0827ae428 / ext3 errors=remount-ro 0 1 UUID=b50965f1-a2e1-443f-876f-578b5f93cbf1 none swap sw 0 0 UUID=881e3ad9-31c4-4296-ae60-eae6c98ea45f none swap sw 0 0 UUID=30d8ae34-e2f0-44b4-bbcc-22d761a128f6 /data btrfs defaults,compress,autodefrag 0 0 What I'd like to do is to place / into the btrfs pool too. The ideal solution would provide the flexibility to boot from any disk in the system alike, so if the main drive fails I'd just need to swap another one into the main slot and it would be bootable like the main one. My main problem is, everything I do needs to result in a bootable system that is open to ssh logins via network as this server is 100% headless so there is no possibility to boot it from a live cd or anything like that. So I'd like to be extra sure everything works out fine :) How would I best go about this? Can anybody hint me to guides or whip something up for these tasks? Anything I forgot to think about? Copy root-data into btrfs pool, adjust mountpoints,... Adjust GRUB to boot from btrfs pool UUID or the local device where GRUB is installed Sync GRUB to all harddrives so every drive is equally bootable (is this even possible without destroying the btrfs partitions on the drives or would I need to disconnect the drives, install grub on them and then connect them back with a slightly smaller partition?)

  Read the article

• External HDD incorrectly detected as internal - how change to enable hot swap/eject?

  - by Sam

  I have win 7 x64 Home Prem. The HDD is a seagate barracuda, 7200.7 ST3120827AS. 3.5", Serial: 3ms006n6, Firmware: 3.42 (no further updates) NexStar CX External case (drivers installed). I have three drives: WD320 with OS installed WD750 data storage (internal) seagate 120 (external) - connected via esata board connected to sata on motherboard (MSI p43 neo) Tried uninstalling HDD in device manager to no effect. Also the internal WD750 is detected as an external drive and win taskbar icon allows for it to be ejected (unlike the seagate). All drives are configured - Online, Simple, Basic, NTFS, Active, Primary Partition (except c drive). The seagate was previously used as a primary disk with XP operating system so I deleted the volume and created/reformatted (not quick). HDD is no longer "Active". But did not fix problem. Background Originally, I installed win 7 with the bios set to IDE and forgot to install the chipset drivers. Then I changed win 7 to install the AHCI drivers, changed the bios to AHCI and rebooted. Win 7 loaded drivers but WD HDD gave problems/crashed. I installed chipset drivers and latest intell storage matrix software thingie (in safe mode). Everything worked fine after that except for the problem of not corrrectly detecting the external drive] I have noticed that under the driver properties (and similarly in the registry) the two drives are configured differently (e.g. in driver details property capabilities for the WD the value is set to 0000006, CM_DEVCAP_REMOVABLE & EJECTSUPPORTED - whereas the seagate shows 0000080 & CM_DEVCAP_SURPRISEREMOVALOK). Any easy way to configure things? I tried physically swapping the sata connections on the mainboard without success So far I have found that a solution to my problem might be to perform some reg changes: How do I remove the option to eject SATA drives from the Windows 7 tray icon?

  Read the article

< Previous Page | 380 381 382 383 384 385 386 387 388 389 390 391  | Next Page >