Search Results

Search found 11685 results on 468 pages for 'intel core i5'.

Page 389/468 | < Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >

• A lots of Apache processes are using my CPU uses always more than 70%

  - by Barkat Ullah

  I am running a plesk panel in 1and1. I have 120 sites running and all are using pligg cms, each site has 600 visitors per day. Please see the details of my server below: HDD-1000GB RAM-16GB Processor-6 Core I always see a lot of apache processes running in my # top view, so the server seems overloaded. If I can reduce the amount apache processes I think the server will be ok. But I don't know why too many apache processes are running. Please see the link below for the screenshot of my # top view: http://dl.dropbox.com/u/26967109/%23Top-2.jpg Sometimes I saw too many connection error in my plesk control panel, so I added the below line in my [mysqld] section: set-variable=max_connections=416 But I didn't find a solution yet. I have also added maxclients and serverlimit 416 in the config /etc/httpd/conf/httpd.conf But no solution yet. I am researching around more than 7 days but don't get any solution. Please help me to solve the problem. In peak hours my sites are taking too much time to load, but off-peak hour it is ok. Please help me to find out the actual problem.

  Read the article

• Nginx + php-fpm - recv() error

  - by Ilya Biryukov

  I get the follow error in the nginx log [error] 17734#0: *6643 recv() failed (104: Connection reset by peer) while reading response header from upstream, client: [cut], server: [cut], request: "GET /venues HTTP/1.1", upstream: "fastcgi://127.0.0.1:9000", host: "[cut]" I have a dedicated box with 8 gb ram, quad core chip. Good server. Nginx, php-fpm & mysql all latest versions running under ubuntu 10.04 I only get this when I stress test the server with siege. If I increase the number of concurrent connections to 100, I can get up to 20% of all requests to fail. Furthermore, I don't get this on pages that have no mysql queries. And only a few failures on pages with moderate number of queries. Bit, I'm not sure if that's got to do anything with it. I have a feeling this is something to do with php. But I can't figure it out. Any suggestions of where to even start looking? Update: and the php error log is silent. No record of anything going wrong

  Read the article

• Outlook 2007 "Mark as Not Junk" Dialog Confusion

  - by David

  Outlook 2007's "Not Junk" button opens the "Mark as Not Junk" dialog. The dialog works correctly if I keep the "Always trust e-mail from <email address>" option checked. That is, the message is removed from the Junk folder and returns to the Inbox. However, if I uncheck the "Always trust" box, pressing OK dismisses the dialog, but nothing else happens. Why not? According to Outlook help, "When you mark a message as not junk, you are given the option of adding the sender or the mailing list name to your Safe Senders List or Safe Recipients List." That sure makes it sound like this is just an option, and not necessary for the core functionality of the action. I really don't want to trust a (possibly forged) From: address, but I do want my mail back in the Inbox. I could manually drag it, but I'm assuming that marking a message as not junk also trains some kind of bayesian filter. Am I mistaken? Thanks.

  Read the article

• MacBook Pro and Backtrack 5R1 Configuration

  - by user119346

  I have a Macbook pro Quad core (2.2/8gb ram/750gb hdd). I have went through tons of forums on the Internet, but none of them seemed to be updated for the current Backtrack 5R1, or the question of getting it to correctly work on the MBP. Can anyone help? I don’t have a USB Dongle, and I want to be able to use the internal airport extreme wireless of the MBP to use BT 5R1. I have downloaded Backtrack 5R1 onto VMWare Fusion, and got it up and running, but to no avail. It keeps recognizing my card as a Ethernet connection. Kismac wont recognize the card either. So what I am asking for is this: The proper “download method.” for Backtrack 5R1 to my MacBook Pro. (YES I AM WILLING TO RE-DOWNLOAD BT 5R1). The Complete process from start to finish, UP TO DATE, from someone who has done this using an MBP Running Lion OSX. The proper tweaks, settings, or commands to get my airport extreme wireless card to work (it is BROADCOM 4331 I think). The wireless connection I need to use the tools on both Backtrack 5R1 and Kismac. I mainly need to test WEP cracking on my network for security. The difference between running BT 5R1 on VMWARE Fusion and running from downloading it directly to the MBP, if there is, How to download it directly to the MBP?

  Read the article

• Dedicated virtual setup is slow with WordPress

  - by kovshenin

  Hey. I'm running a Fedora linux server on the Amazon EC2 platform. I'm pretty sure there's something wrong with my configuration as it seems to be very slow. SSH sometimes takes over 30 seconds to connect, a WordPress generated web page could take 5 seconds to load, and it could take 20 seconds to load, which is pretty awkward. MySQL queries are all executed in less than a second, so I don't think that's the case. I'm not really sure where the issue lies, but a simple page written in PHP loads instantly. A fresh WordPress installation starts lagging. Same works perfect on grid hosting at MediaTemple for instance, so I'm pretty sure I missed something. If you could please direct me to the right tools and articles which would help me out. Thanks so much! Fedora Core 8, php 5.2.6, MySQL 5.0.45, OpenSSH 4.7p1, OpenSSL 0.9.8b. PHP is configured as a module to Apache 2.2.9, all websites based on virtual hosts. I have some on-going php scripts running from time to time in the background via cron. Thanks.

  Read the article

• Ubuntu purple splash screen with blinking pixels?

  - by joxnas

  I had ubuntu 9.10 I upgraded to 10.04 after solving some problems (freeze at boot). Since then, I don't have the ubuntu's logo showing up when I boot, but a purple screen with some blinking pixels. I didn't care much about it... but today my computer took too long at that screen (normally it was just 1/4 second, but today it was like a minute..). And it happened like 4 or 5 times in a row (Only at the 5th time I realised that it was not freezing up, but it simply would took more time) After a reboot, it is again 1/4 second of purple screen but I don't want this problem to return.. so I want to get rid of the purple screen (I think it is an indicator of the problem) Well, I already installed the graphic drivers (going to system admnistration hardware drivers). But it didn't solve anything. (I don't know if it is even related) I searched in google, found something old (2006) and I think it maybe has some relation with my problems .. http://ubuntuforums.org/archive/index.php/t-294692.html But couldn't understand the conversation (i'm a linux novice) Sorry for my horrible english.. I would appreciate any help! My hardware: ATI Mobility Radeon 4650 HD P7450 2.13Ghz Core 2 Duo

  Read the article

• IIS6 Multiple SSL websites to a single HTTP website?

  - by docflabby

  Running a IIS6 server on Windows 2003. All the websites use ASP.NET I have a number of websites all running separate HTTP websites: www.domain1.com www.domain2.com www.domain3.com I have a separate HTTPS website www.secure.com These websites are all running on the same server. I now wish to intergrate the content of www.secure.com into each of the domains in a transparent way. Such that each website despite having its own SSL connection displays the same website. The complicatrion is www.secure.com needs to know which website the connection has come from to apply the appropriate branding. The idea behind this is to have only one website, and location, but it keeps the core website brand. https://domain1.com looks alot better from a marketing point of view (and avoids users getting confused about what our secure website is) SSL www.domain1.com/secure - displays www.secure.com (branded domain1) SSL www.domain2.com/secure - displays www.secure.com (branded domain2) SSL www.domain3.com/secure - displays www.secure.com (branded domain3) How would the best way of achieving this, i'm open to using additional software if necessery. Would a reverse proxy be sutible for this situation?

  Read the article

• Error compiling PHP 5.5.9 on CentOS 6.5 during make command

  - by Chris Mancini

  Here is the error message: cc: internal compiler error: Killed (program cc1) Please submit a full bug report, with preprocessed source if appropriate. See <file:///usr/share/doc/gcc-4.6/README.Bugs> for instructions. make: *** [ext/fileinfo/libmagic/apprentice.lo] Error 1 The very last thing make was processing is apprentice.lo which appears to be part of the image manipulation libraries (maybe?). I am using Ansible to provision my instance. It is a Digital Ocean single core 512MB VM. I have been using vagrant / ansible with the same config locally for dev and it has compiled fine, this is the first cloud VM I am attempting to provision. The only difference is the base image for my DO server is coming from DO and for my local dev, I built my own Vagrant box via VirtualBox from a stock CentOS basic server install. I pull it down from my DropBox. The problem has been experienced by others and reported as a php bug report My php ansible role up to the error: --- - name: Download php source get_url: url={{ php_source_url }} dest=/tmp register: get_url_result - name: untar the source package command: tar -xvf php-{{ php_version }}.tar.gz chdir=/tmp when: get_url_result.changed or php_reinstall - name: configure php 5.5 command: > ./configure --prefix={{ php_prefix }} --with-config-file-path={{ php_config_file_path }} --enable-fpm --enable-ftp --enable-mbstring --enable-pdo --enable-soap --enable-sockets=shared --enable-zip --with-curl --with-fpm-group={{ nginx_group }} --with-fpm-user={{ nginx_user }} --with-freetype-dir=/usr/lib64/ --with-gd --with-jpeg-dir=/usr/lib64/ --with-libdir=lib64 --with-mcrypt --with-openssl --with-pdo-mysql --with-pear --with-readline --with-tidy --with-xsl --with-zlib --without-pdo-sqlite --without-sqlite3 chdir=/tmp/php-{{ php_version }} when: get_url_result.changed or php_reinstall - name: make clean when reinstalling command: make clean chdir=/tmp/php-{{ php_version }} when: php_reinstall - name: make php command: make chdir=/tmp/php-{{ php_version }} when: get_url_result.changed or php_reinstall Thanks in advance for any help. :)

  Read the article

• Trouble with nginx and serving from multiple directories under the same domain

  - by Phase

  I have nginx setup to serve from /usr/share/nginx/html, and it does this fine. I also want to add it to serve from /home/user/public_html/map on the same domain. So: my.domain.com would get you the files in /usr/share/nginx/html my.domain.com/map would get you the files in /home/user/public_html/map With the below configuration (/etc/nginx/nginx.conf) it appears to be going to my.domain.com/map/map as noticed by this: 2011/03/12 09:50:26 [error] 2626#0: *254 "/home/user/public_html/map/map/index.html" is forbidden (13: Permission denied), client: <edited ip address>, server: _, request: "GET /map/ HTTP/1.1", host: "<edited>" I've tried a few things but I'm still not able to get it to cooperate, so any help would be greatly appreciated. ####################################################################### # # This is the main Nginx configuration file. # ####################################################################### #---------------------------------------------------------------------- # Main Module - directives that cover basic functionality #---------------------------------------------------------------------- user nginx; worker_processes 1; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; #---------------------------------------------------------------------- # Events Module #---------------------------------------------------------------------- events { worker_connections 1024; } #---------------------------------------------------------------------- # HTTP Core Module #---------------------------------------------------------------------- http { include /etc/nginx/mime.types; default_type application/octet-stream; log_format main '$remote_addr - $remote_user [$time_local] "$request" ' '$status $body_bytes_sent "$http_referer" ' '"$http_user_agent" "$http_x_forwarded_for"'; access_log /var/log/nginx/access.log main; sendfile on; keepalive_timeout 65; server { listen 80; server_name _; #access_log logs/host.access.log main; location / { root /usr/share/nginx/html; index index.html index.htm; } location /map { root /home/user/public_html/map; index index.html index.htm; } error_page 404 /404.html; location = /404.html { root /usr/share/nginx/html; } error_page 500 502 503 504 /50x.html; location = /50x.html { root /usr/share/nginx/html; } } include /etc/nginx/conf.d/*.conf; }

  Read the article

• VLAN ACLs and when to go Layer 3

  - by wuckachucka

  I want to: a) segment several departments into VLANs with the hopes of restricting access between them completely (Sales never needs to talk to Support's workstations or printers and vice-versa) or b) certain IP addresses and TCP/UDP ports across VLANS -- i.e. permitting the Sales VLAN to access the CRM Web Server in the Server VLAN on port 443 only. Port-wise, I'll need a 48-port switch and another 24-port switch to go with the two existing 24-port Layer 2 switches (Linksys); I'm looking at going with D-Links or HP Procurves as Cisco is out of our price range. Question #1: From what I understand (and please correct me if I'm wrong), if the Servers (VLAN10) and Sales (VLAN20) are all on the same 48-port switch (or two stacked 24-port switches), afaik, the switch "knows" what VLANs and ports each device belongs to and will switch packets between them; I can also apply ACLs to restrict access between VLANs at this point. Is this correct? Question #2: Now lets say that Support (VLAN30) is on a different switch (one of the Linksys) switches. I'm assuming I'll need to trunk (tag) switch #2's VLANs across to switch #1, so switch #1 sees switch #2's VLAN30 (and vice-versa). Once Switch #1 can "see" VLAN30, I'm assuming I can then apply ACLs as stated in Question #1. Is this correct? Question #3: Once Switch #1 can see all the VLANs, can I achieve the seemingly "Layer 3" ACL filtering of restricting access to Server VLAN on only certain TCP/UDP ports and IP addresses (say, only permitting 3389 to the Terminal Server, 192.168.10.4/32). I say "seemingly" because some of the Layer 2 switches mention the ability to restrict ports and IP addresses through the ACLs; I (perhaps mistakenly) thought that in order to have Layer 3 ACLs (packet filtering), I'd need to have at least one Layer 3 switch acting as a core router. If my assumptions are incorrect, at which point do you need a Layer 3 switch for inter-VLAN routing vs. inter-VLAN switching? Is it generally only when you need that higher-level packet filtering ability between your departments?

  Read the article

• SQLSTATE[HY000]: General error: 2006 MySQL server has gone away

  - by Barkat Ullah

  Server details: RAM: 16GB HDD: 1000GB OS: Linux 2.6.32-220.7.1.el6.x86_64 Processor: 6 Core Please see the link below for my # top preview: I can often see the error mentioned in title in my plesk panel and my /etc/my.cnf configuration are as below: bind-address=127.0.0.1 local-infile=0 datadir=/var/lib/mysql socket=/var/lib/mysql/mysql.sock user=mysql max_connections=20000 max_user_connections=20000 key_buffer_size=512M join_buffer_size=4M read_buffer_size=4M read_rnd_buffer_size=512M sort_buffer_size=8M wait_timeout=300 interactive_timeout=300 connect_timeout=300 tmp_table_size=8M thread_concurrency=12 concurrent_insert=2 query_cache_limit=64M query_cache_size=128M query_cache_type=2 transaction_alloc_block_size=8192 max_allowed_packet=512M [mysqldump] quick max_allowed_packet=512M [myisamchk] key_buffer_size=128M sort_buffer_size=128M read_buffer_size=32M write_buffer_size=32M [mysqlhotcopy] interactive-timeout [mysqld_safe] log-error=/var/log/mysqld.log pid-file=/var/run/mysqld/mysqld.pid open_files_limit=8192 As my server httpd conf is set to /etc/httpd/conf.d/swtune.conf and the configuration is as below: at prefork.c: <IfModule prefork.c> StartServers 8 MinSpareServers 10 MaxSpareServers 20 ServerLimit 1536 MaxClients 1536 MaxRequestsPerChild 4000 </IfModule> If I run grep -i maxclient /var/log/httpd/error_log then I can see everyday this error: [root@u16170254 ~]# grep -i maxclient /var/log/httpd/error_log [Sun Apr 15 07:26:03 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting [Mon Apr 16 06:09:22 2012] [error] server reached MaxClients setting, consider raising the MaxClients setting I tried to explain everything that I changed to keep my server okay, but maximum time my server is down. Please help me which parameter can I change to keep my server okay and my sites can load fast. It is taking too much time to load my sites.

  Read the article

• Is it possible for a faulty processor to cause audio static/noise?

  - by Tom

  I have a Core 2 Extreme processor I received from a friend and have set up an XBMC box using it. However, I constantly get audio static whenever playing any music or videos. Here is a video of the sound: http://www.youtube.com/watch?v=SqKQkxYRVA4 I have tried replacing everything short of the case and the processor, including cables, audio interfaces, operating systems, ram, etc, leading me to think it might be either the case shorting out the motherboards I have tried or a faulty processor. Is it possible for a faulty processor to cause audio static/noise? Any feedback would be appreciated. Edit - Here's a list of things I have tried: Reinstalling OS Installing/upgrading/repairing PulseAudio/Alsa Installing alternate OSes, straight Ubuntu, Lubuntu, Xubuntu, Arch, Mint, Windows 7 Switching audio from the external card to internal Optical, audio out through HDMI, audio out through headphones Different ports on receiver (my main desktop sounds fine on the same sound system) Different optical cables Unplugging everything unnecessary from the motherboard (1 HD, 1 Stick of Ram, 1 Keyboard) Swapping out ram Swapping out the motherboard Replacing the Graphics Card (was replaced due to fan being noisy, not specifically for this problem) Different harddrives Swapping power supply Disabling onboard audio Switching Power Cable Plugging in through surge protector Plugging into different outlet on separate circuit

  Read the article

• High latency due to non-presence of a transit provider in my country

  - by nixnotwin

  My ISP, a state owned incumbent, buys bandwidth from different transit providers. Whenever it buys transits it announces only a specific prefix (in most cases a hitherto unused) through the new transit AS. For e.g. if it runs out of bandwidth, it buys bandwidth from a new transit and announces a new prefix through it, while the same prefix is not announced (or announced with lowest metrics, so that the routes are very rarely used) via the old transits which continue to provide bandwidth to it. I am a business customer, so I have a fiber based link to the ISP and a tiny subnet is given to me. The subnet which is provide to me is part of a prefix which is announced by the AS of a transit who, it seems, do not have a presence in my country. So when I do a trace the packets, when they leave my ISP's AS, they take about 275ms to reach the transit providers core router, which is located in USA (half the world away). Also for upstream traffic my ISP uses a transit provider (tier 1) who has a presence in my country. But the return path is always through the transit which is in USA. So, average latency is 400ms. All the users of other ISPs in my country discover my subnet via USA. Even the traffic from neighboring countries, from Europe (which is much nearer) follows the path via USA. Sites using CDNs also resolve to ips in USA. I have informed the ISP NOC about the issue and I have asked them to provide an ip subnet belonging to a prefix announced by a local transit (preferably a tier 1 transit provider) and I am waiting for a reply. My question: Is it a serious issue that I must follow up to get it resolved? When I compared the latency on other providers in my country, it is, in most cases, less than half of my ISPs latency. Why my ISP doesn't announce all its prefixes to all of its transit providers, so that the packets can take efficient and nearest routes to reach prefixes that originate within its network?

  Read the article

• HP DL185 - very slow disk read speed

  - by fistameeny

  Hi, I have a HP DL185 G6 Server (12 disk model) with the following spec: Quad Core Xeon 2.27GHz 6GB RAM HP P212 RAID controller with battery backup 2 x 128GB 15K SAS 3.5" (RAID-1 for the operating system) 4 x 750GB 7.5K SAS 3.5" (RAID-5 for the data, 2TB usable space) The operating system is Ubuntu Server 9.10. Both drives have been formatted as EXT4. We are finding that read speed of the RAID-5 array is poor. Disk test results below: sudo hdparm -tT /dev/cciss/c0d1p1 /dev/cciss/c0d1p1: Timing cached reads: 15284 MB in 2.00 seconds = 7650.18 MB/sec Timing buffered disk reads: 74 MB in 3.02 seconds = 24.53 MB/sec For info, the RAID-1 array performs as follows: sudo hdparm -tT /dev/cciss/c0d0p1 /dev/cciss/c0d0p1: Timing cached reads: 15652 MB in 2.00 seconds = 7834.26 MB/sec Timing buffered disk reads: 492 MB in 3.01 seconds = 163.46 MB/sec We thought this was because with no battery, read/write cache is disabled. We have bought and installed the battery backup and have used the HP bootable CD to change the cache settings to 50% read / 50% write and check cache is enabled on the drives and the controller. Is there something I'm missing?

  Read the article

• Desktop Provisioning for a Small Linux Software Development Team

  - by deakblue

  Goal: Get a small team using a standard development image rather than 4 software devs setting up their own environments. Why: it takes a day or days to install a distro, build-specific libraries, tools like editors and IDEs, mysql, couchdb, java, maven, python, android-sdk, etc. It's a giant PITA that when repeated 4 times by 4 developers (not sys admins) wastes time and generates annoying divergences that crop up later (it-builds-on-my-box syndrome). There's no sharing of productivity, settings, tricks, scripts, set-ups. Some of this is helped by segregating the build systems into headless virtualbox images. This doesn't really address tooling though or the GUI-desktop dev that needs doing. So I see three basic strategies, ghosting, virtualization, and finally creating a kind of in-house linux distro (I guess Google does something like this). The target dev environment is based on Debian OpenBox and must allow a mix of 3rd gen Core i7 notebooks 8GB-minimum to work both single and multihead. Important, the lappies are not the same, but a mix of 2012 macbooks and PCs. So: virtualization: is doing all of your work within a VM, like VirtualBox, practical on this hardware or annoying. ghosting: will laptops from different manufacturers make this impractical. DIY distro: short of scripting a bunch of package installs, I don't know if there's any "distro-maker" that could keep this from being an epic project of scripting package installs. So any advice?

  Read the article

• Intermittent extrememly long response times when downloading documents

  - by pap

  I have a Java web application running om Tomcat 7 with an Apache httpd 2.2 fronting with mod_jk/AJP. One part of the application is serving files (up to 4mb size). Now, normally this all runs very smooth with stable, low response-times. However, in rare instances (<0.1% of downloads), the downloadtime will go beyond 1 minute. After activating the ThreadStuckValve in Tomcat, I can see that the long responses seem to be stuck at org.apache.tomcat.jni.Socket.sendbb(Native method) i.e network I/O. At most, these long-running downloads take 5 minutes, which I strongly suspect is because of the default 300 second timout in Apache 2.2 (http://httpd.apache.org/docs/2.2/mod/core.html, "TimeOut directive"). To me, this looks like network problems. The Apache timeout (if that is what is kicking in at the 5 minute mark) indicates that ACK packets are not being transmitted correctly. My questions are what could be causing this? Closed browser at receiving end but socket not signaled as closed properly? Packet loss or some other network failure in transit? Where would I start troubleshooting this? We're running Tomcat and Apache on Windows server 2008-R2 in a vmware virtualized server.

  Read the article

• Windows Server 2008 R2 running at a snail's pace

  - by Django Reinhardt

  Really weird problem here. Our main web server has started running at a snail's pace, for absolutely no reason we can discern. Even after restarting the machine, when there's no little or no ram usage and CPU usage is fluctuating between 0 and 30%, simple tasks, like opening Internet Explorer, or waiting for My Computer to open, take forever. There are no processes hogging system resources that we can see... the machine itself is just exhibiting extremely slow behaviour. I've never seen a machine do this. A lot of security updates had built up, so we decided to let Windows install them. When we looked through the history upon restarting, though, they had failed with error code 800706BA. I don't know if this could be related or not. Any help in this matter would be greatly appreciated. As mentioned in the title, we're running a Windows Server 2008 R2 machine. It's also running SQL Server and IIS. It has 16GB of RAM and a decent Quad Core processor. It's also been fine until now -- and we haven't changed a thing. Thanks for any help.

  Read the article

• Faking a Linux environment without chroot

  - by Pascal

  For a university project I want to test a C++11 program on a 32-core machine. Unfortunately the machine has Ubuntu 12.04 with GCC 4.6 installed (we need GCC 4.7 because of some C++11 threading features). In such an environment I would normally run a chroot with a custom linux (say a debootstrap with Ubuntu 12.10). Since we don't get root access on the machine we can't use chroot. So far I have prepared a run-time environment using debootstrap for our code, I compiled it in the debootstrap environemnt. Then copied it onto the server (using rsync). In order to run our C++ code I set the LD_LIBRARY_PATH to export LD_LIBRARY_PATH=~/debootstrap/usr/lib/:~/debootstrap/lib64/:~/debootstrap/usr/lib/x86_64-linux-gnu/:~/debootstrap/lib/x86_64-linux-gnu/:$LD_LIBRARY_PATH and so far our code seems to run. I'm however stuck with our python code. It doesn't seem to be sufficient to set the paths manually. export PYTHONPATH=~/debootstrap/usr/lib/python2.7/dist-packages:~/debootstrap/usr/lib/python2.7:~/debootstrap/usr/lib/python2.7/plat-linux2:~/debootstrap/usr/lib/python2.7/lib-tk:~/debootstrap/usr/lib/python2.7/lib-dynload:~/debootstrap/usr/local/lib/python2.7/dist-packages:~/debootstrap/usr/lib/pymodules/python2.7:~/debootstrap/usr/lib/python2.7/dist-packages/PIL:~/debootstrap/usr/lib/python2.7/dist-packages/gtk-2.0:~/debootstrap/usr/lib/python2.7 Executing our script results in ImportError: No module named _path Is there an easier way to accomplish a "fake"-chroot than just overriding and creating environment variables? Note I need python since we created a custom C++-Python module in order to run our tests. Maybe I should create two questions from this.

  Read the article

• Debian Bluetooth headphones not working

  - by cYrus

  Hardware Headphones Bluetooth dongle Maybe not exactly these models. Setup I tried to follow some guides, here's what I've done so far: Install software: sudo apt-get install bluez-utils bluez-alsa Reboot (just to be sure): $ dmesg | grep -i bluetooth [ 20.268212] Bluetooth: Core ver 2.16 [ 20.268230] Bluetooth: HCI device and connection manager initialized [ 20.268233] Bluetooth: HCI socket layer initialized [ 20.268235] Bluetooth: L2CAP socket layer initialized [ 20.268239] Bluetooth: SCO socket layer initialized [ 20.284685] Bluetooth: RFCOMM TTY layer initialized [ 20.284692] Bluetooth: RFCOMM socket layer initialized [ 20.284693] Bluetooth: RFCOMM ver 1.11 [ 20.335375] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 20.335378] Bluetooth: BNEP filters: protocol multicast The deamon is running: $ /etc/init.d/bluetooth status [ ok ] bluetooth is running. Plug the dongle: $ dmesg | tail [...] [23108.352034] usb 5-2: new full-speed USB device number 2 using ohci_hcd [23108.571131] usb 5-2: New USB device found, idVendor=0a12, idProduct=0001 [23108.571136] usb 5-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0 [23108.629042] usbcore: registered new interface driver btusb Put the headphones in pairing mode, and try scanning: $ hcitool scan Scanning ... Found nothing. What's next? What should I try? I'll update this answer as soon as you provide me hints.

  Read the article

• Virtualization in Ubuntu 9.10

  - by Jeff Dege

  I have an existing Centos 5 installation. I would like to upgrade to Ubuntu. Thing is, I don't want to be down for as long as it will take to get my entire environment moved over - software installed, connectivity configured, etc. I'd like to take it one step at a time. But I don't really want to keep rebooting back and forth from the new OS to the old OS. That's what I did last time I upgraded to a new OS, and it got old real fast. So, since my new MB is virtualization-ready (AMD Phenom II 945 quad-core), I figured I could create a virtual machine, under the new OS installation, that ran the old OS installation. The problem is that the documentation I've been able to find has been pretty sparse. I've found a lot of possibilities, and little info on which would be capable of doing what I want. I have a new Ubuntu 9.10 installation, and a second disk containing the Centos 5 installation. And I don't know where to go next. Any help would be appreciated.

  Read the article

• Server Recovery from Denial of Service

  - by JMC

  I'm looking at a server that might be misconfigured to handle Denial of Service. The database was knocked offline after the attack, and was unable to restart itself after it failed to restart when the attack subsided. Details of the Attack: The Attacker either intentionally or unintentionally sent 1000's of search queries using the applications search query url within a couple of seconds. It looks like the server was overwhelmed and it caused the database to log this message: Server Specs: 1.5GB of dedicated memory Are there any obvious mis-configurations here that I'm missing? **mysql.log** 121118 20:28:54 mysqld_safe Number of processes running now: 0 121118 20:28:54 mysqld_safe mysqld restarted 121118 20:28:55 [Warning] option 'slow_query_log': boolean value '/var/log/mysqld.slow.log' wasn't recognized. Set to OFF. 121118 20:28:55 [Note] Plugin 'FEDERATED' is disabled. 121118 20:28:55 InnoDB: The InnoDB memory heap is disabled 121118 20:28:55 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121118 20:28:55 InnoDB: Compressed tables use zlib 1.2.3 121118 20:28:55 InnoDB: Using Linux native AIO 121118 20:28:55 InnoDB: Initializing buffer pool, size = 512.0M InnoDB: mmap(549453824 bytes) failed; errno 12 121118 20:28:55 InnoDB: Completed initialization of buffer pool 121118 20:28:55 InnoDB: Fatal error: cannot allocate memory for the buffer pool 121118 20:28:55 [ERROR] Plugin 'InnoDB' init function returned error. 121118 20:28:55 [ERROR] Plugin 'InnoDB' registration as a STORAGE ENGINE failed. 121118 20:28:55 [ERROR] Unknown/unsupported storage engine: InnoDB 121118 20:28:55 [ERROR] Aborting **ulimit -a** core file size (blocks, -c) 0 data seg size (kbytes, -d) unlimited scheduling priority (-e) 0 file size (blocks, -f) unlimited pending signals (-i) 13089 max locked memory (kbytes, -l) 64 max memory size (kbytes, -m) unlimited open files (-n) 1024 pipe size (512 bytes, -p) 8 POSIX message queues (bytes, -q) 819200 real-time priority (-r) 0 stack size (kbytes, -s) 8192 cpu time (seconds, -t) unlimited max user processes (-u) 1024 virtual memory (kbytes, -v) unlimited file locks (-x) unlimited **httpd.conf** StartServers 10 MinSpareServers 8 MaxSpareServers 12 ServerLimit 256 MaxClients 256 MaxRequestsPerChild 4000 **my.cnf** innodb_buffer_pool_size=512M # Increase Innodb Thread Concurrency = 2 * [numberofCPUs] + 2 innodb_thread_concurrency=4 # Set Table Cache table_cache=512 # Set Query Cache_Size query_cache_size=64M query_cache_limit=2M # A sort buffer is used for optimizing sorting sort_buffer_size=8M # Log slow queries slow_query_log=/var/log/mysqld.slow.log long_query_time=2 #performance_tweak join_buffer_size=2M **php.ini** memory_limit = 128M post_max_size = 8M

  Read the article

• What is the best cloud technology to use for MongoDB/GridFS database servers

  - by Nerian

  We are going to launch a service that will require between 1 and 2 GB for file storage per paid user. I am going to use GridFS for storing files. GridFS is a module for MongoDB that allows to store large files in de database. I am pondering the different options for storing the database. But since I am unexperienced at deployment and it is my first time with Mongodb I need your experience. Criteria: I want to spend my time developing my core business, that is, my own application. I am a Ruby on Rails developer. I do not like to mess with server configuration. Hence, I would like a fully managed hosting solution. But I would like to know about any other option, if you think it is worth it. It should be able to scale. Cloud style. Pay as you go. The lower the price, the better. So far I known of these services: https://mongohq.com/pricing https://mongomachine.com/pricing https://mongolab.com/about/pricing/ http://cloudcontrol.com/add-ons/mongodb/ And they seem to be OK for common needs, that is no file storage. But I am going to use GridFS, so the size matters. These services seems to scale, in price, quite poorly. MongoHQ: The larger plan max storage is 20 GB. Seems like a very little storage, for GridFS. MongoMachine: Flat price, 2.5$ per GB. I didn't found the limit. Seems like a good price, comparing the others. MongoLab: 3.984 GB max, which I don't think I will hit, so perfect. 8$ per GB, quite costly. CloudControl: The larger plan is 20 Gb. The custom service starts at 250€ plus some unspecified charge per GB. What is your experience with these services? Any downtimes? Other possibilities? Edit: Added meaning of GridFS

  Read the article

• Windows 8 x64 with VMWare Workstation or inside ESXi

  - by Dommer

  I need to run several virtual machines on a core i7-920 box with 12GB or RAM and a 256GB SSD to host the VMs. It also has a Highpoint RocketRaid 2720SGL RAID controller with a 12TB RAID 5 array. I want one of my VMs to run Windows 8 x64, to have access to the RAID array as a native disk (not as networked drives and it needs to run at full speed) and to be able to send files quickly across the network. Initially I thought I'd try to do this using ESXi 5, but I have been unable to find any working RAID drivers for the RR2720SGL and it is not on the HCL for ESXi 5. In light of this, I have installed Windows 8 x64 on the hardware and am thinking of installing VMWare Workstation and running my VMs inside there. I guess my questions are these: How does VMWare Workstation 9 perform compared to ESXi 5? In the real world I mean? Presumably installing Win 8 as the host OS will give me way better performance for that Win 8 machine than Win 8 running under ESXi? I should stick with Windows 8 x64 as the host OS, right? If I install a domain controller VM inside my Win 8 box and join the Win 8 machine to that domain, am I insane (I would guess the Win 8 machine wouldn't see the domain controller until it finished starting everything up, but I don't think that matters)?! is it feasible to give metrics like this and if so, what is the likely value of x? 25%? 50%? 75%? Win 8 under ESXi runs x% as fast as Win 8 installed bare metal.

  Read the article

• GUI interfaces to ATI card behave weirdly out of the box and after updates.

  - by jdk

  My Lenovo W500 came with an ATI Mobility FireGL V5700 and both the Catalyst control center software and Vista display manager display four monitors. What's really annoying is the behaviour. My two active displays (laptop display + my external monitor) are always #s 3 and 4 respectively which doesn't make sense. This is out of the box. Additionally dragging & dropping is jumpy and displays #1 and 2 (always inactive because they don't exist to the software) are often preventing me from dragging #3 and 4 to the rightmost side. They also auto-snap to weird positions and certain sensible positions like position one directly over top of the other are not possible. The exact same annoyances are present when using the Windows Display manager too. In other words the interface is crap and I'm looking for a fix that's not wishing I had gone with nVidia instead. I've updated drivers, and Catalyst control centre. Have latest Windows and AMD/ATI updates. Any thoughts? Graphics Software Driver Packaging Version 8.563.2.1-090401a-079160C-Lenovo Provider ATI Technologies Inc. 2D Driver Version 7.01.01.849 2D Driver File Path /REGISTRY/MACHINE/SYSTEM/ControlSet001/Control/Class/{4D36E968-E325-11CE-BFC1-08002BE10318}/0001 Direct3D Version 7.14.10.0630 OpenGL Version 6.14.10.8306 Catalyst® Control Center Version 2009.0401.1328.22301 Graphics Hardware Primary Adapter Graphics Card Manufacturer Powered by ATI Graphics Chipset ATI Mobility FireGL V5700 Device ID 9591 Vendor 1002 Subsystem ID 2126 Subsystem Vendor ID 17AA Graphics Bus Capability PCI Express 2.0 Maximum Bus Setting PCI Express 2.0 x16 BIOS Version 010.088.000.021 BIOS Part Number BK-ATI VER010.088.000.021.034663 BIOS Date 2009/09/30 Memory Size 512 MB Memory Type DDR3 Core Clock in MHz 600 MHz Memory Clock in MHz 700 MHz

  Read the article

• Compressing and copying large files on Windows Server?

  - by Aaron

  I've been having a hard time copying large database backups from the database server to a test box at another site. I'm open to any ideas that would help me get this database moved without having to resort to a USB hard drive and the mail. The database server is running Windows Server 2003 R2 Enterprise, 16 GB of RAM and two quad-core 3.0 GHz Xeon X5450s. Files are SQL Server 2005 backup files between 100 GB and 250 GB. The pipe is not the fastest and SQL Server backup files typically compress down to 10-40% of the original, so it made sense to me to compress the files first. I've tried a number of methods, including: gzip 1.2.4 (UnxUtils) and 1.3.12 (GnuWin) bzip2 1.0.1 (UnxUtils) and 1.0.5 (Cygwin) WinRAR 3.90 7-Zip 4.65 (7za.exe) I've attempted to use WinRAR and 7-Zip options for splitting into multiple segments. 7za.exe has worked well for me for database backups on another server, which has ~50 GB backups. I've also tried splitting the .BAK file first with various utilities and compressing the resulting segments. No joy with that approach either- no matter the tool I've tried, it ends up butting against the size of the file. Especially frustrating is that I've transferred files of similar size on Unix boxes without problems using rsync+ssh. Installing an SSH server is not an option for the situation I'm in, unfortunately. For example, this is how 7-Zip dies: H:\dbatmp>7za.exe a -t7z -v250m -mx3 h:\dbatmp\zip\db-20100419_1228.7z h:\dbatmp\db-20100419_1228.bak 7-Zip (A) 4.65 Copyright (c) 1999-2009 Igor Pavlov 2009-02-03 Scanning Creating archive h:\dbatmp\zip\db-20100419_1228.7z Compressing db-20100419_1228.bak System error: Unspecified error

  Read the article

< Previous Page | 385 386 387 388 389 390 391 392 393 394 395 396  | Next Page >