Search Results

Search found 16106 results on 645 pages for 'custom channel'.

Page 393/645 | < Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >

• Error - "IR Hardware not detected" - but it's installed/working

  - by Robert

  I am trying to do: Settings-TV-Set up TV signal. During this process I am getting the error "IR Hardware not detected." With the remote, I can select the "try again" button (to re-detect) and it tries again, so the remote works. Plugging in the "IR blaster" doesn't change anything. (I wouldn't expect any difference, but I read a post which said you needed that. I will get Media Center to change channels if I can get that working - but first things first.) I was able to do the setup months ago when I had cable. and everything was fine. I just got DirecTV. (BTW - During the above process, Media Center detects the signal coming in on channel 3. Windows XP Media Center SP3. The TV Tuner card is a Pinnacle TCTV HD PCI. Everything - and I mean everything - has the latest firmware and drivers - as of 4 months ago when I fixed a different problem. So I DON"T WANT TO HEAR the standard answer to check drivers/firmware. THANK YOU.) Thanks for any help.

  Read the article

• GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Alternative software for Pinnacle PCTV 100e

  - by Stijn Sanders

  I have a Pinnacle PCTV 100e external USB cable television receiver. I've been using Pinnacle's software that came with the card (TVCenter Pro) to record things at given times. Things I don't like is an extremely high CPU load, and that it doesn't seem to halt the screensaver from running when watching in full screen. Also, I was away the last two weeks, and the schedules went terribly bust. Some items were recorded hours before or after the actual scheduled time (and now I missed some shows), and some recurring schedules weren't converted into the next occurrence correctly! Is there good alternative software that would work with my PCTV 100e? (Preferalby cheap or free) I've tried VLC Player, which gets video, but no audio. I've tried MediaPortal, which crashes when trying to scan for channels. When I select a channel manually, the stored mpg has big errors in encoding and is also missing audio. There's VirtualDub, but that doesn't have ready-made scheduled-recording options. This I can conjure some scheduled scripts for, but I've noticed the sync gets awfully wrong after some time. I've tried Windows Media Center, but it doesn't seem to support the PCTV 100e.

  Read the article

• How to use WPA2 client mode in the Linux-based Cisco WAP4410N access point

  - by joechip

  I have a Cisco WAP4410N access point that I want to use as a client to connect to a WPA2 wireless network (for WLAN service monitoring purposes). Supposedly this access point supports a "Wireless Client/Repeater" mode that allows to do this. The Repeater function is optional (I have that box unchecked so that nobody can connect to this access point wirelessly). I have verified through SSH that the access point gets configured as a client and not as a Master. But it never associates to the SSID I ask it to. This is what iwconfig shows: ath04 IEEE 802.11ng ESSID:"myownssid" Mode:Managed Channel:0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/3 Retry:off RTS thr:off Fragment thr:off Encryption key:off Power Management:off Link Quality=0/94 Signal level=161/162 Noise level=161/161 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 Although I've never done this from the command line, I suppose I could use wpa_supplicant or wpa_client to associate it, but I don't know how to do that without editing configuration files and the filesystem is readonly. Besides, I would have to run those commands manually after every reboot. I'd like to know how to do this the Cisco way, if possible. If not, any trick to make this work would be useful. Edit: This is with the latest firmware, 2.0.4.2. And I found that not all of the filesystem is readonly, since /var and /tmp are mounted with type ramfs.

  Read the article

• SSH client not showing prompt after successful login

  - by user431949

  I'm having problems with my SSH client on Ubuntu 10.10. When I switch on my computer and open a Terminal and execute the command ssh user@host, it gives me a password prompt after which I enter the right password, I then get a prompt to execute my commands on the remote computer. Now the problem is, after a little while (probably around 10 minutes), the terminal window stops accepting commands (No matter what I type, nothing shows). Once this happens, I close the Terminal window and try to start all over again by opening another Terminal window. But this time around, after entering the right password, I don't get a welcome message or prompt. The cursor just keeps blinking on a new line. I ran the ssh command with -v parameter and the message I get after a successful login is: debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_GB.utf8 Still the cursor keeps blinking on a new line without a prompt. However, Putty SSH client works perfectly on the same machine. Thank you very much for your time. Your help would be greating appreciated.

  Read the article

• Connecting jconsole using SOCKS to Amazon EC2

  - by freshfunk

  I'm trying to use jconsole to view stats on an EC2 instance by using a socks proxy created by SSH. I've tried the various scripts mentioned in the links below but to no avail: http://simplygenius.com/2010/08/jconsole-via-socks-ssh-tunnel.html http://gabrielcain.com/blog/2010/11/02/using-ssh-proxying-to-connect-jconsole-to-remote-cassandra-instances/ I'm running ssh -f -ND 8123 myuser@mymachine and verified that at least Firefox goes through it as a proxy. I then run jconsole -J-DsocksProxyHost=localhost -J-DsocksProxyPort=8123 service:jmx:rmi:///jndi/rmi://ec2-XX-XX-XXX-XXX.compute-1.amazonaws.com:8080/jmxrmi I run netstat -n on my EC2 instance and I see a connection created by my machine. However, the connection eventually disappears and I get a 'channel 2: open failed: connect failed: Operation timed out' from my ssh tunnel. I've opened the jmx port through the security group and I've checked the port on the EC2 instance to make sure it's open (by telnet-ing to it). I'm not sure where to look next. Are there some properties in sshd_config or ssh_config I need to enable for tunneling? Or anything in Mac OS X? I feel like a serious noob but sys administration is really not my strong point. I've spent several hours and can't get this to work.

  Read the article

• pppd disconnects from 3G, doesn't reconnect, w/ persist set

  - by bytenik

  I am trying to configure pppd to connect to a 3G network (Sprint, in this case) and then stay connected, reconnecting automatically if the remote connection is terminated. I have enabled the persist option. My configuration file is as follows: hide-password noauth connect "/usr/sbin/chat -v -f /etc/chatscripts/cellular" debug /dev/cell 921600 defaultroute noipdefault user " " persist maxfail 0 lcp-echo-failure 10 lcp-echo-interval 60 holdoff 5 However, when the peer disconnects the connection, pppd often waits a long time (substantially more than my holdoff) to reconnect the modem -- if it ever reconnects at all! An example log showing this: May 23 05:17:24 00270e0a8888 pppd[2408]: rcvd [LCP TermReq id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: LCP terminated by peer May 23 05:17:24 00270e0a8888 pppd[2408]: Connect time 60.1 minutes. May 23 05:17:24 00270e0a8888 pppd[2408]: Sent 0 bytes, received 0 bytes. May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down started (pid 2456) May 23 05:17:24 00270e0a8888 pppd[2408]: sent [LCP TermAck id=0x26] May 23 05:17:24 00270e0a8888 pppd[2408]: Script /etc/ppp/ip-down finished (pid 2456), status = 0x0 May 23 05:17:24 00270e0a8888 pppd[2408]: Hangup (SIGHUP) May 23 05:17:24 00270e0a8888 pppd[2408]: Modem hangup May 23 05:17:24 00270e0a8888 pppd[2408]: Connection terminated. May 23 05:17:24 00270e0a8888 pppd[2408]: Terminating on signal 15 May 23 05:17:24 00270e0a8888 pppd[2408]: Exit. May 23 06:08:07 00270e0a8888 pppd[2500]: pppd 2.4.5 started by root, uid 0 May 23 06:08:10 00270e0a8888 pppd[2500]: Script /usr/sbin/chat -v -f /etc/chatscripts/cellular finished (pid 2530), status = 0x0 May 23 06:08:10 00270e0a8888 pppd[2500]: Serial connection established. May 23 06:08:10 00270e0a8888 pppd[2500]: using channel 11 The disconnect at the request of the peer occurs at 5:17, but the reconnect didn't happen until 6:08. I had a friend monitoring the server so I'm not certain that this wasn't a manual reconnection. Either way, it either took almost an hour to reconnect or never reconnected. Shouldn't persist + holdoff 5 cause this to automatically reconnect after 5 seconds of the link terminating?

  Read the article

• Connection refused in ssh tunnel to apache forward proxy setup

  - by arkascha

  I am trying to setup a private forward proxy in a small server. I mean to use it during a conference to tunnel my internet access through an ssh tunnel to the proxy server. So I created a virtual host inside apache-2.2 running the proxy, the proxy_http and the proxy_connect module. I use this configuration: <VirtualHost localhost:8080> ServerAdmin xxxxxxxxxxxxxxxxxxxx ServerName yyyyyyyyyyyyyyyyyyyy ErrorLog /var/log/apache2/proxy-error_log CustomLog /var/log/apache2/proxy-access_log combined <IfModule mod_proxy.c> ProxyRequests On <Proxy *> # deny access to all IP addresses except localhost Order deny,allow Deny from all Allow from 127.0.0.1 </Proxy> # The following is my preference. Your mileage may vary. ProxyVia Block ## allow SSL proxy AllowCONNECT 443 </IfModule> </VirtualHost> After restarting apache I create a tunnel from client to server: #> ssh -L8080:localhost:8080 <server address> and try to access the internet through that tunnel: #> links -http-proxy localhost:8080 http://www.linux.org I would expect to see the requested page. Instead a get a "connection refused" error. In the shell holding open the ssh tunnel I get this: channel 3: open failed: connect failed: Connection refused Anyone got an idea why this connection is refused ?

  Read the article

• Are These Parts compatible?

  - by ell

  I have never assembled a PC before, although I have taken an old one apart and replaced a few parts in others here and there so I have (very) limited experience. I have been looking to make a pc and here are the parts I might buy: Foxconn P45AL Intel P45 (Socket 775) DDR2 Motherboard (with onboard sound I believe) Gigabyte GeForce GTX 460 OC 768MB GDDR5 PCI-Express Graphics Card Already have 2 1gb sticks of dual channel DDR2 memory Intel Core 2 Quad Q8400 LGA775 'Yorkfield' 2.66GHz 4MB-cache Processor Samsung SpinPoint F3 1TB SATA-II 32MB Cache Hard Drive Antec Dark Fleet Series DF10 Gaming Enclosure – Black I already have monitor, mouse, keyboard and DVD/CD drive Akasa Freedom Power 1000W Modular Power Supply I have never done this before so feel free to laugh at me for getting something obvious wrong, forgetting a vital component etc. but is all of this compatible? And have I gone overkill on the PSU, if so, please recommend one. Thanks in advance, ell. EDIT: Added PSU which I forgot to mention EDIT: I would be using this to surf the internet, write e-mails, chat, word process, play games such as team fortress 2 & spring rts (at highest graphics hopefully), some 3d modelling in blender, some opengl programming, and image editing in GIMP.

  Read the article

• Home network with two isolated separate subnets, running on cablemodem/router and WRT-router.

  - by Johan Allgoth

  I have a new connection with a nice new router/cable-modem. I'd like to setup it up optimally and needs some pointers. I am a complete n00b when it comes to routing. I want to end up with two separate subnets, 10.1.2.0/24 and 192.168.1.0/24 each available on their own wireless channel/SSID. Both firewalled. I want my wired computers on the gigabit switch, optimally with public ips. I want to be able to reach 192.168.1.0/24 from 10.1.2.0/24, but not vice versa. Everyone should have internet access. Hardware and capabilities: Netgear CG3100. Handles cable connection. Gigabit switch. 802.11n. Can do DHCP, firewall, NAT etc. Can choose subnet. Can turn of NAT and if so hand out up to 4 public ips. Somewhat challenged when it comes to configuration. WRT-router. Runs DD/Open-WRT very stable. 100 Mbit switch. 802.11.g Can do DHCP, firewall, NAT etc. Can choose subnet. Highly configurable. I hope to be able to keep 10.1.2.0/24 on the CG3100, for speed reasons and 192.168.0.0/24 on the WRT-router for quota and user control reasons. On my 10.1.2.0/24 network I plan on running servers for various services. Should I turn of NAT on the WRT-router? Or on the cable modem? Activate what in that case? Is double NAT always f-ed up?

  Read the article

• Decyphering Seagate drive model numbers?

  - by Stefan Lasiewski

  I'm comparing Seagate's Enterprise and Desktop drives for a variety of old and new servers. These servers come from different generations, so options like size (73GB, 2TB) and interface (SATA vs SAS 3.0Gbps vs SAS 6Gbps vs SCSI Ultra320) are widely variable. I'm trying to compare the sizes, speeds and interfaces, but I'm getting thrown off by different models. Also, their website is not the best. Does anyone know of a documented explanation of the Seagate model numbers? And is there a single spreadsheet which compares the features for all drives (or all 'Enterprise' drives?). Seagate drives have model numbers like this: Model ST3600057SS 6-Gb/s SAS 600 GB None at Cheetah® 15K Hard Drives Model ST373455LW Ultra320 SCSI 73.4 GB 68-Pin LW at Cheetah® 15K Hard Drives Model ST32000644NS SATA 3Gb/s 2 TB None at Constellation™ ES Hard Drives Model ST973452SS 6-Gb/s SAS 73 GB None Savvio® 15K Hard Drives Model ST9200011FS SATA 3Gb/s 200 GB Pulsar™ Solid State Drives I understand the model numbers read something like this: ST - SOMETHING1 - SIZE - SOMETHING2 - INTERFACE Where the fields mean something like this: ST : For 'Seagate'? 'Seagate Technoligies'? SOMETHING1 - This field has number, but I'm not sure what that represents. SIZE - Size in Gigabytes. This is a number like '73' or '300' or '2000' SOMETHING2 - This field also has a number, but I'm not sure what it means. INTERFACE - This field seems to indicate the Interface. 'SS' means SAS, 'FC' means Fibre Channel, but I don't see how to distinguish between 6Gbps SAS and 3Gbps SAS, or different SATA or FC speeds. I don't see a field which indicates the RPM (15K , 10K, 7.2K) etc. Is this part of the model number?

  Read the article

• Photoshop CS4. How do I make sure my color stays the same in my different .psd files? (could be RGB

  - by Kris

  I asked 2 photoshop experts I know but they haven't got a clue because all my settings are exactly the same, in both files. (except the RGB type !! I'm not sure. Please read on) I use RGB color, 72DPI, 8 bits / channel. No adjustments (filters, like greyscale, etc ...) are selected / used. The layers are both normal, and opacity and fill are 100% (yes, in both files). I took two screenshots, and you can see the difference: http://www.flickr.com/photos/30465871@N05/4623864297/ http://www.flickr.com/photos/30465871@N05/4624469754/ Both colors are ff795d, but that doesn't matter, any color I use gives me the same problem: they both look different. Now, I know the CMYK settings (see screenshots) are different, but when the settings are the same the color changes. Why is this happening and how do I solve this problem? My guess is I'm working with different a type of RGB. It's sRGB IE61966 - 2.1 in the file I created (file info raw data) but I can't find that in the file that started with a screenshot. If that's the problem, how do I change / convert the RGB, once the file is already open? Thank you.

  Read the article

• Why Is Volume Shadow Copy Services stopping?

  - by David Mackintosh

  I am running Windows 7 Professional, 64-bit. I am running a backup-over-the-internet software client which depends on the Volume Shadow Copy Services running. Since I installed Service Pack 1 (or rather, didn't object when Windows Update forced Service Pack 1 on me) the backup service is failing to back everything up because VSC isn't running. Most of the time it fails to back up such noise as the Security Essentials database or the Messenger Live contact list -- stuff I really don't care about -- but I don't want to fall into the trap of accepting an Error-state backup as "normal". At the recommendation of the backup software, I have set the VSC service startup mode to be Automatic. When I look in the Event Log, System channel I can see at boot time: The Volume Shadow Copy service entered the running state. ...and then two or three minutes later: The Volume Shadow Copy service entered the stopped state. How do I figure out why VSC is stopping? At the suggestion of the backup vendor, I have already followed the suggestions from http://support.microsoft.com/default.aspx/kb/940184 net stop SENS net stop EventSystem net start EventSystem net start SENS net stop COMSysApp net stop SwPrv net stop VSS cd /d C:\Windows\system32 regsvr32 ole32.dll /s regsvr32 oleaut32.dll /s regsvr32 vss_ps.dll /s vssvc /register /s regsvr32 /i swprv.dll /s regsvr32 /i eventcls.dll /s regsvr32 es.dll /s regsvr32 stdprov.dll /s regsvr32 vssui.dll /s regsvr32 msxml.dll /s regsvr32 msxml3.dll /s regsvr32 msxml4.dll /s net start SwPrv net start VSS net start ProtectedStorage ...and per http://support.microsoft.com/kb/940184 I have deleted the key tree HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\EventSystem\{26c409cc-ae86-11d1-b616-00805fc79216}\Subscriptions I have also run chkdsk /F and chkdsk /R on both permanent hard disks. (I had a similar problem with another computer (same OS, same failure, same start point after SP1 install) but the problem went away when I forced Volume Shadow Copy Services to Automatic startup rather than Manual. I did not have to resort to following the Microsoft KB instructions.)

  Read the article

• VMWare Raw Device Mapping Not Working

  - by George H. Lenzer

  While I'm waiting for VMWare support to get back to me, I thought I'd ask here. I have a 400 gig LUN presented from a fiber channel SAN to my VMWare host. It's legacy from another virtualization platform and I need to keep it as is to avoid a long period of downtime. I formatted my VMFS3 datastore with 4 meg blocks to allow up to 1 TB disks. Then I tried adding my 400 gig disk as a raw device in physical compatibility mode. I get the error: "File is larger than the maximum size supported by datastore 'Base Test'. [Base Test]VMTEST01/VMTEST01_2.vmdk Originally I had the VMFS datastore formatted with 1 meg blocks which was the cause of this problem since the largest disk allowed would be 256 gigs. But I deleted the data store and then reformatted with 4 megs blocks. I've also tried using virtual compatibility mode for the raw device but it still fails. Does anyone have any suggestions? I've been waiting for a little over a week for VMWare, but that's fine because I'm not yet a paying customer. I'm still in the eval phase.

  Read the article

• Which upgrade path for disk IO bound postgres server?

  - by user41679

  Hi all, We currently have a Sun x4270 with 2xquad core Xeon Nehalmen 2.93ghz cores (16 threads), 72 gig of ram and 16 x 10k SAS disks split between the os raid 1, a partition for the Write Ahead Logs which is raid 10 and a partition for the database tables and indexes which is also raid 10, all xfs. I'm currently evaluating which path to go down in terms of upgrades. We'll be sharding the DB at some point soon, but for now I need to focus on hardware upgrades specifically. The machine is not CPU or memory bound at all at the moment, just IOWait is become an issue. The machine is mostly write access as we have a heavy caching layer. We're seeing about 300 write IOPS average on both the database partitions. We don't have any additional storage infrastructure like a Fiber Channel or ISCSI network. Budget isn't too much of a concern, something inline with the size of this server (i.e no $1m IBM machines) Space is ok on the DB side of things, we're running out obviously but there's also some reduction we can do. Additional space would be good though. My current thoughts are either: * ISCSI SAN, possible with 10Gbit network that has solid state acceleration. * FusionIO card / Sun F20 card (will the FusionIO card work in the Sun box? * DAS shelf (something like this http://www.broadberry.co.uk/das-direct-attached-storage-servers/cyberstore-224s-das) which a combination of 15k sas disks and some Intel X25-E drives for DB indexes etc) what would I need to put in the x4270 to add a DAS shelf? I think it's a SAS HBA card, do I have to use Sun's own card or will any PCI Express card work? Anything else??? what would you guys do from your experience? I appreciate it's a lot of questions, but I haven't expanded a DB machine for a number of years and the landscape has changed dramatically since then! Any advice or feedback would be very much appreciated. Let me know if there's anything else I can clarify. Thanks in advance!

  Read the article

• Multi-WAN bonding across different media

  - by Tom O'Connor

  I've recently been thinking again about a product that Viprinet provide, basically they've got a pair of routers, one that lives in a datacentre, Their VPN Multichannel Hub and the on-site hardware, their VPN multichannel routers They've also got a bunch of interface cards (like HWICs) for 3G, UMTS, Ethernet, ADSL and ISDN adapters. Their main spiel seems to be bonding across different media. It's something that I'd really like to use for a couple of projects, but their pricing is really quite extreme, the hub is about 1-2k, the routers are 2-6k, and the interface modules are 200-600 each. So, what I'd like to know is, is it possible with a couple of stock Cisco routers, 28xx or 18xx series, to do something similar, and basically connect a bunch of different WAN ports, but have it all presented neatly as one channel back to the internet, with seamless (or nearly) failover if one of the WAN interfaces should fail. Basically, If i got 3x 3G to ethernet modems, and each on a different network, I'd like to be able to loadbalance/bond across all of them, without having to pay Viprinet for the privilege. Does anyone know how I'd go about configuring something for myself, based around standard protocols (or vendor specific ones), but without actually having to buy the Viprinet hardware?

  Read the article

• Troubleshooting wireless client-bridged networks between two DD-WRT routers?

  - by KronoS

  I recently purchased a Buffalo N600 wireless router which came with DD-WRT pre-installed. I want to take my old wireless router a Linksys WRT54GL, also with DD-WRT pre-installed, and use it as a wireless bridge for my HTPC and Blu-Ray Player in the other room. I other words, I'm trying to connect to WIRED networks via the wireless on the routers. I followed eactly the instruction from DD-WRT's manual for 'Client Bridged' however I'm still not able to connect to two routers correctly, when the encryption is enabled (WPA2-Personal Mixed) however I am able to connect the two routers when there is NO encryption. I've checked, double checked, and triple checked that EVERYTHING is the same on BOTH routers: Routers 1 & 2 Encryption: WPA2-Personal Mixed Wireless Mode: G-Only Wireless Channel: 6 Subnet Mask: 255.255.255.0 Subnet: 192.168.1.0/254 SSID: Krono$ Primary Router #1 (Buffalo N600) IP Address: 192.168.1.1 Firewall: Enables w/ defaults DCHP: Enabled as DHCP Server Secondary Router #2 (Linksys WRT54GL) IP Address: 192.168.1.2 Firewall: Disabled as per DD-WRT instructions I'm looking for any configurations that I may have missed, or settings that may need to happen in order for this work.

  Read the article

• Controller Error: Do I need to worry?

  - by Kryten

  I have a HP Pavillion dv5224ea Laptop with Windows 7 on it. Recently I discovered a Error in Event Viewer: The driver detected a controller error on \Device\Ide\IdePort1. (more details): - System - Provider [ Name] atapi - EventID 11 [ Qualifiers] 49156 Level 2 Task 0 Keywords 0x80000000000000 - TimeCreated [ SystemTime] 2010-03-07T12:43:07.090197600Z EventRecordID 30198 Channel System Computer Alistair-Win7 Security - EventData \Device\Ide\IdePort1 0000100001000000000000000B0004C002000000850100C00000000000000000000000000000000000000000000000000000000004100000 -------------------------------------------------------------------------------- Binary data: In Words 0000: 00100000 00000001 00000000 C004000B 0008: 00000002 C0000185 00000000 00000000 0010: 00000000 00000000 00000000 00000000 0018: 00000000 00001004 In Bytes 0000: 00 00 10 00 01 00 00 00 ........ 0008: 00 00 00 00 0B 00 04 C0 .......À 0010: 02 00 00 00 85 01 00 C0 ......À 0018: 00 00 00 00 00 00 00 00 ........ 0020: 00 00 00 00 00 00 00 00 ........ 0028: 00 00 00 00 00 00 00 00 ........ 0030: 00 00 00 00 04 10 00 00 ........ Event Viewer is recording A LOT of these errors (sometimes 13, one after the other!). Do I need to worry? What does this error mean? What device could "\Device\Ide\IdePort1" be? What is a ATAPI Error? Do I need to re-install Windows? I generally find the occurs when I try to backup my machine (using Windows Backup) or when using a program that uses Volume Shadow Copy. I have run "sfc", no problems. There are no Device Errors in Device Manager. I have also run "vssadmin list writers", no problems. Whats going on??? Would it be a good idea to re-install Windows 7?

  Read the article

• GA 8KNXP Rev1.0: 4GB installed, only 3.5 recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4GB. The specs from the manual say: Maximum memory support: 4GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Computer does not boot after ram upgrade

  - by Calmarius

  I have a Dell Optiplex GX520 desktop (it's abount 5 yr old) PC with 512 MB DDR2 RAM. Since my computer always swapping I thought I should upgrade my RAM. I bought a Kingmax 2GB DDR2 RAM. But my system does not boot. The status leds are on 2 and 4. The user manual says 'video card failure' wtf? I put back the original module and everything works. I tried many combinations. When I leave the old 512 RAM in and put the 2GB next to it to the other socket my system completes the POST and I'm able to enter the BIOS menu. It says my system has 2.5 GB installed, one 0.5GB and one 2GB in dual asymmetric channel mode. It's seemingly right. Exiting the BIOS setup GRUB loads successfully, but when I try to boot Ubuntu it crashes with kernel panic immediately. Trying to load Windows XP does not get past the loading screen, it crashes with 0x8E stop error. Does this mean the ram I bought is faulty? Or is it just mean that the memory module I bought is too new to be handled my computer? I this case I may exchange the RAM with my friends. No other computer is in my house (my very old box has DDR1 ram, my systers new box has DDR3 ones. I can't plug my memory in neither one.) I'm going to return the RAM to store to replace it with a better one tomorrow. Is there any hope to get this new module work?

  Read the article

• Too many concurrent connections Exchange 2010. What else is there to check?

  - by hydroparadise

  I thought that I had this under control before. But for some reason during our last email marketing promo, I start receiving from our mass email client (built in house).. The message could not be sent to the SMTP server. The transport error code is 0x800ccc67. The server repsonse was 421 4.3.2 The maximum number of concurrent connections has exceeded a limit, closing transmission channel again. There's several places I've checked to make sure that wouldn't be an issue. First I checked that receive connector was set to receive an adequate number of connections on our relay connector (1000 connections). Then, I would later find out about Throttling Policies. I created one and set all the properties I knew to set in terms of the policy following properties to 1000; EWSMaxConcurrency, OWAMaxConcurrency, CPAMaxConcurrency, and CPAMaxConcurrency. Still, the email client starts receiving the error shortly after 100 has been sent and takes about 15-30 seconds. The process is then repeatable, but still the error gets received at the same spot everytime. Is there a rate setting that I am missing? Was there a windows update that I missed looking at? Should the software have it's own throttling feature?

  Read the article

• SBD killing both cluster nodes when there are even small SAN network problems

  - by Wieslaw Herr

  I am having problems with stonith SBD in a openais-based cluster. Some background: The active/passive cluster has two nodes, node1 and node2. They are configured to provide an NFS service to users. To avoid problems with split-brain, they are both configured to use SBD. SBD is using two 1MB disks available to the hosts via an multipath fibre-channel network. The problems start if something happens with the SAN network. For example, today one of the brocade switches got rebooted and both nodes lost 2 out of 4 paths to each disks, which resulted in both nodes committing suicide and rebooting. This, of course, was highly undesirable because a) there were paths left b) even if the switch would be out for 10-20 seconds a reboot cycle of both nodes would take 5-10 minutes and all NFS-locks would be lost. I tried increasing the SBD timeout values (to 10sec+ values, dump attached at the end), however a "WARN: Latency: No liveness for 4 s exceeds threshold of 3 s" hints that something isn't working as I would it expect to. Here is what I would like to know: a) Is SBD working as it should killing nodes when 2 paths are available? b) If not, is the multipath.conf file attached correct? The storage controller we use is an IBM SVC (IBM 2145), should there be any specific configuration for it? (as in multipath.conf.defaults) c) How should I go about increasing the timeouts in SBD attachements: Multipath.conf and sbd dump (http://hpaste.org/69537)

  Read the article

• Wireless does not work on Ubuntu 9.04

  - by Yongwei Xing

  Hi all I install the Ubuntu 9.04 my old Lenovo Y520 laptop, the wirless does not work.My Wireless card is Intel Pro/wireless 2100 card. But I can not enable it. My wired card is working well. Does anyone meet it before. the ifconfig output is eth0 Link encap:Ethernet HWaddr 00:0a:e4:5f:6c:30 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:973 errors:0 dropped:0 overruns:0 frame:0 TX packets:1025 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:574701 (574.7 KB) TX bytes:169249 (169.2 KB) Interrupt:10 eth1 Link encap:Ethernet HWaddr 00:0c:f1:58:79:b5 UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:10 Base address:0x8000 Memory:d0202000-d0202fff lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:8 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:480 (480.0 B) TX bytes:480 (480.0 B) the output of iwconfig is eth1 unassociated ESSID:off/any Nickname:"ipw2100" Mode:Managed Channel=0 Access Point: Not-Associated Bit Rate:0 kb/s Tx-Power:off Retry short limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 I have another question. When my OS is 9.04, there is a icon about network connection on the panel at the top. After I upgraded to 9.10, that icon disappeared. How can I get that back? Best Regareds,

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

• nginx: dump HTTP requests for debugging

  - by Alexander Gladysh

  Ubuntu 10.04.2 nginx 0.7.65 I see some weird HTTP requests coming to my nginx server. To better understand what is going on, I want to dump whole HTTP request data for such queries. (I.e. dump all request headers and body somewhere I can read them.) Can I do this with nginx? Alternatively, is there some HTTP server that allows me to do this out of the box, to which I can proxy these requests by the means of nginx? Update: Note that this box has a bunch of normal traffic, and I would like to avoid capturing all of it on low level (say, with tcpdump) and filtering it out later. I think it would be much easier to filter good traffic first in a rewrite rule (fortunately I can write one quite easily in this case), and then deal with bogus traffic only. And I do not want to channel bogus traffic to another box just to be able to capture it there with tcpdump. Update 2: To give a bit more details, bogus request have parameter named (say) foo in their GET query (the value of the parameter can differ). Good requests are guaranteed not to have this parameter ever. If I can filter by this in tcpdump or ngrep somehow — no problem, I'll use these.

  Read the article

< Previous Page | 389 390 391 392 393 394 395 396 397 398 399 400  | Next Page >